400AP LCR User Manual - Janus Remote Communications
Contents
1. AP Hardware Guide This is a more focused table pertaining to only the Routers usable interfaces Recommended Operating Conditions Parameter Minimum Nominal Maximum Unit Note Operating Temperature 30 80 C 1 Supply Supply amp Enable Input T 26 Volts 1 Peak Supply Power 12 5 Watts 1 Average Supply Current TBD Notes 1 Peak supply power specification is stated as the minimum amount of power the external power supply must supply during the TX burst of the embedded cellular radio Please refer to the Plug In User Manual for power supply characteristics of the embedded Plug In Module embedded in the 400AP Router 2 Average supply current specification is stated as the maximum average current the 400AP Router can draw while maintaining junction temperatures within the internal power supply IC s specification Getting started with the 400AP Router This section will take you through setting up the 400AP Router and creating a connection to the internet Before we begin If the 400AP Router is a GSM HSPA type you must insert a SIM card to the internal Plug in Modem for functionality The details on how to do that are as follows Step 1 To access the 400AP board remove the four TX 10 screws from the ruggedized aluminum enclosure These screws are located on the back panel of the 400AP where the DB9 and lock header are located Terminus 400AP LCR User Guide JAO7 UM_LCR Page6 Rev A01 Date 10 23 142. JAN U S REMOTE Copyright 2014 Janus Remote Communications Specifications subject to change without notice C MMUNICATI NS NEP All Rights Reserved See website for latest revision Not intended for life support applications Getting started with the 400AP Router continued Step 2 Slide out the back panel which will include the 400AP board Step 3 Locate the SIM Card slot on top of the Terminus Plug In board Step 4 To insert the SIM card in the SIM card slot slide the top of the cover back to unlock Insert the SIM card in the cover slot and close Slide back to original position to lock in place Step 5 Slide the back panel and 400AP board into the aluminum enclosure Replace the four TX 10 screws and tighten them back on to enclosure Terminus 400AP LCR User Guide JAO7 UM_LCR Page 7 Rev A01 Date 10 23 14 JAN U S REMOTE Copyright 2014 Janus Remote Communications Specifications subject to change without notice C MMUNICATI NS All Rights Reserved See website for latest revision Not intended for life support applications Getting started with the 400AP Router continued Configuring the router The router can be configured via a web GUI with the default address at 192 168 2 1 8080 Step 1 Ensure the following are connected to the 400AP Router e Ethernet cable to your computer e Power supply e Antenna Step 2 Apply power to the router you should see the red LED illuminate and the yellow LED illuminate eithe
3. Terminus 400AP LCR Products User Manual JANUS ee mor C MMUNICATI NS Bulletin __JA07 UM_LRC A01 Date 23 Oct 2014 TABLE OF CONTENTS TABLE OF CONTENTS and DISCLAIMER viscciscensanensnvsciwevaiwannswantnsannpaniavantktaabapaantonesuonsintnapeebenendussebaancowancpuaneebuampreeanswcaiaubaneee 2 ACOAP LOR General Descrip OR a ene aaa ee eee ney ee ee ne eer ee ee ee ee ne anes el eee ere ee ree ere errs 3 SO NT E TED E D Na ai a mae tenner sen tere er fre 3 User GLS LS Lei nane enaa E AAE AEA REA 4 6 DC Power Jack USB RS232 Ethernet SD Memory Card 20P Header Reset Mode LED Indicators Antenna Connection Ue URSS ea IOI PSP Ze 6 Getting Started with the 400AP LCR Router ccccsecceeeceeeeeseeeceneeeeeeeeseaseeseaaeeseaseeceasseeeaueeeeaseeeeseesesessansessoneessaneeees 7 12 Before We Begin Configuring the Router OPS INI STO AN esc cares EEE 13 ROC AIS OR a reer a ee ee en ae ein eet rm eer eee ne 13 DISCLAIMER The information contained in this document is the proprietary information of Connor Winfield Corporation and its affiliates Janus Remote Communication The contents are confidential and any disclosure to persons other than the officers employees agents or subcontractors of the owner or licensee of this document without the prior written consent of Connor Winfield is strictly prohibited Connor Winfield makes every effort to ensure the quality of the information it makes available Notwithstandin
4. e About The 400AP Router is preconfigured for use with a GSM GPRS EDGE CDMA UMTS and HSPA communication networks They were specifically designed to provide customers with cost effective products that are easily integrated into new and existing designs require limited customer certification resources and are completely interchangeable to allow for maximum network flexibility while removing the worry of product obsolescence Configure the cellular radio used by your router in this section The radio will use one of the following cellular radios GSM Quad band EGSM 850 900 1800 1900 MHz HSPA UMTS HSPA Penta Band 850 900 1700 1900 2100 MHz CDMA Dual band CDMA 800 1900 MHz EVDO Dual Band CDMA2000 1xRTT 1xEV D Rev A 800 1900 MHz Note For GSM and HSPA networks an Access Point Name APN is required You can also optionally enter a GPRS username and password if they are required by your service Router Reboot is REQUIRED to apply new settings Reboot Now Cellular Radio Config Step 4 On the main page you will be presented with a few tabs e Cellular Configuration This is for cellular network settings such as entry for the APN given by the provider e Router This is where you can set the host IP address name and DHCP settings e Port Forwards Set your port forwards as required for your local network e Administration Change port number restore the default configuration e About Version lookup a
5. e reboot the device so all settings take effect You can do this by clicking the Reboot Now button located in the upper right hand corner it appears on all tabs when prompted to do so Note After pressing the Reboot Now button you will be prompted that the router is rebooting with a wait screen Do not power off the device until this process completes 192 168 2 1 8080 router index login_success True v Ra Google Please wait The router is rebooting Step 10 Once rebooted if the APN and other network settings are correct the green LED will illuminate upon a successful PPP connection being made Once this LED illuminates open your browser and attempt a simple connection to www google com to test Terminus 400AP LCR User Guide JAO7 UM_LCR Page 12 Rev A01 Date 10 23 14 JAN U S REMOTE Copyright 2014 Janus Remote Communications Specifications subject to change without notice COMMUNICATIONS A bases All Rights Reserved See website for latest revision Not intended for life support applications Terminus 400AP LCR Products User Manual Ordering Information Ordering Information Description EVDO4OOAP LCR v2 0 EV DO Sprint EVDO400AP LCR v3 0 EV DO Verizon HSPA400AP LCR v1 0 HSPA AT amp T T Mobile Revision History Revision Revision Date Note A00 02 27 14 Advanced Release User Manual A01 10 23 14 Updates to Configurations and Miscellaneous edits JANUS z
6. ecifications subject to change without notice C MMUNICATI NS All Rights Reserved See website for latest revision Not intended for life support applications Getting started with the 400AP Router continued Configuring the router continued Step 5 On the Cellular Configuration page scroll to the bottom and find the Cellular Radio Config area Success Configuration saved Cellular Radio Config Radio HE910 Network N A APN web omwtoday com Username N A Password N A Janus Remote Communications 1970 If not already filled in and grayed through automatic detection select the cellular modem type GSM HSPA Based Unit HE910 Set the APN to what the provider has given you In this example we are utilizing i2gold If your account required a username and password enter it here most do not though CDMA EVDO CE910 DE910 Based Unit If available set the Network type to Sprint or Verizon There will be no APN Username Password required Click Save and continue It will warn of requiring a reboot which we will do at the end of this Terminus 400AP LCR User Guide JAO7 UM_LCR Page10 Rev AO Date 10 23 14 JAN U S REMOTE Copyright 2014 Janus Remote Communications Specifications subject to change without notice C MMUNICATI NS bases All Rights Reserved See website for latest revision Not intended for life support applications Getting started with the 400AP Router continued Config
7. evel access Ethernet 10 100 PHY The 400AP Router contains a single Ethernet port with activity LEDs Its implementation is compliant with IEEE802 3 IEEE802 3U 10BASE T 100BASE TX standards SD Memory Card The micro SD card socket is connected to the multimedia card interface MCI of the 9G20 processor but is unused while in the router configuration 20P Header The locking header connection breaks out many signals useful to the 400AP however in the router configuration it s largely unused save for power Reset The reset button is connected to the reset controller of the 400AP When pressed and released the 400AP is reset Terminus 400AP LCR User Guide JAO7 UM_LCR Page 4 Rev A01 Date 10 23 14 JAN U S REMOTE Copyright 2014 Janus Remote Communications Specifications subject to change without notice C MMUNICATI NS i f All Rights Reserved See website for latest revision Not intended for life support applications Interfaces continued Mode The Mode button is used to place the 400AP Router into different operational modes during boot It s only recommended to explore this if instructed to do so by Janus as by default the bootloader and router application are already in place Mode Entry Conditions Summary Method of Entry Normal Run Mode Condition 400AP powered Apply Power or use Reset Summary 2 Mode button is note pressed After reset is released the red light will illuminate Router application begins No
8. g the foregoing Connor Winfield does not make any warranty as to the information contained herein and does not accept any liability for any injury loss or damage of any kind incurred by use of or reliance upon the information Connor Winfield disclaims any and all responsibility for the application of the devices characterized in this document and notes that the application of the device must comply with the safety standards of the applicable country and where applicable with the relevant wiring rules Connor Winfield reserves the right to make modifications additions and deletions to this document due to typographical errors inaccurate information or improvements to programs and or equipment at any time and without notice Such changes will nevertheless be incorporated into new editions of this application note All rights reserved 2011 Connor Winfield Corporation Terminus 400AP LCR User Guide JAO7 UM_LCR Page2 Rev A01 Date 10 23 14 JAN U S REMOTE Copyright 2014 Janus Remote Communications Specifications subject to change without notice C MMUNICATI NS NEP bases All Rights Reserved See website for latest revision Not intended for life support applications 400AP LCR Open Platform General Description The 400AP Router is a simplified and focused version of our more open platform 400AP single board computer It s designed to give the user an easy up and run cellular routing connection configurable via web GUI it can be set up and
9. in use for the end user very quickly Powered by the Terminus Common Footprint the 400AP router can be utilized across various technologies depending on the user s needs Wired Ethernet N A T z R E W 4 L L JANUS Terminus 400AP LCR User Guide JAO7 UM_ LCR Page3 Rev A01 Date 10 23 14 REMOTE Copyright 2014 Janus Remote Communications Specifications subject to change without notice C MMUNICATI NS gt i NEET All Rights Reserved See website for latest revision Not intended for life support applications Operation Hardware Requirements The following hardware is required for proper operation and setup of the 400AP LCR e AOOAP LCR e 12Vdc Power Supply Janus Part Number MC 0004 e Cellular Antennas e CDMA EVDO Janus Part Number ANT 0073 e GSM HSPA Janus Part Number ANT 0003 e Cat 5 Patch Cable Janus Part Number CBL 0014 Interfaces DC Power jack The 2 1mm center conductor power jack accepts input voltages from 7 to 26VDC Pin Description Center Pin Supply Outer Conductor Supply Supply power can also be applied to the unit through the 30 Pin locking header USB There are two USB ports on the 400AP router one device port and one host port These by default are unused in the router configuration RS232 The 400AP Router has access to RS 232 through the front end DB9 debug port this port only contains RX and TX but can be used for debugging and lower l
10. istered searching for network Slow Blinking 0 3 sec on 2 7 sec off Registered to the network Green LED State Description Permanently OFF Router function is not ready Permanently ON IP address attained router function ready Cellular RF Port SMA Female Pin Description Center Pin Cellular Signal Outer Conductor Signal Ground Terminus 400AP LCR User Guide JAO7 UM_LCR Page5 Rev A01 Date 10 23 14 JAN U S REMOTE Copyright 2014 Janus Remote Communications Specifications subject to change without notice C MMUNICATI NS All Rights Reserved See website for latest revision Not intended for life support applications Electrical Specifications Absolute Maximum Ratings Parameter Minimum Nominal Maximum Unit Note Operating Temperature 30 80 C 1 Supply Supply amp Enable Input 36 36 Volts 1 VIN RS 232 Inputs 25 25 Volts 1 Notes 1 Operation of the device at these or any other conditions beyond those listed under Recommended Operating Conditions is not implied Exposure to Absolute Maximum Rating conditions for extended periods of time may affect device reliability 2 The supply inouts are protected from reverse voltage and transients beyond the Recommended Operating Conditions If transients persist the supply will be latched in a disabled state Once disabled the supply will need to be cycled off and on to reset 3 More verbose table information can be attained in the full 400
11. mor chose PB d LE Janus Remote Communications Europe Division of The Connor Winfield Corporation Bay 143 Shannon Industrial Estate Shannon Co Clare Ireland Phone 353 61 475 666 2111 Comprehensive Drive Aurora Illinois 60505 630 499 2121 e Fax 630 851 5040 www janus rc com
12. nd general information Edit View History Bookmarks Tools Help l l i l h 0 xi File Janus 4004P Bon ______ ales e 192 168 2 1 5080 router index login_success True Cc Janus 400AP Router Configuration admin Cellular Configuration Router Port Forwards Administration About The 400AP Router is preconfigured for use with a GSM GPRS EDGE CDMA UMTS and HSPA communication networks They were specifically designed to provide customers with cost effective products that are easily integrated into new and existing designs require limited customer certification resources and are completely interchangeable to allow for maximum network flexibility while removing the worry of product obsolescence Configure the cellular radio used by your router in this section The radio will use one of the following cellular radios e GSM Quad band EGSM 850 900 1800 1900 MHz e HSPA UMTS HSPA Penta Band 850 900 1700 1900 2100 MHz e CDMA Dual band CDMA 800 1900 MHz e EVDO Dual Band CDMA2000 1XRTT 1xEV D Rev A 800 1900 MHz Note For GSM and HSPA networks an Access Point Name APN is required You can also optionally enter a GPRS username and password if they are required by your service Router Reboot is REQUIRED to apply new settings 2eboot Now Terminus 400AP LCR User Guide JAO7 UM_LCR Page9 Rev A01 Date 10 23 14 JAN U S REMOTE Copyright 2014 Janus Remote Communications Sp
13. r permanently or blink Step 3 Go to your browser of choice in this demonstration we will be using Mozilla Firefox Enter the IP address 192 168 2 1 8080 you will be presented with a login page Username admin Password admin File Edit View History y AS 7 Google 192 168 2 1 8080 account login Janus 400AP Router Configuration Anonymous Login to the AP400 Router administrative control panel Login to your router using the username and password provided in the documentation Once logged in you ll be able to change your password and administer your router Both a username and password are required Username Username Password Janus Remote Communications 2014 The password can be adjusted in the drop down at the top You will be prompted for the old password and the new password you wish to use Terminus 400AP LCR User Guide JAO7 UM_LCR Page8 Rev AO Date 10 23 14 JAN U S REMOTE Copyright 2014 Janus Remote Communications Specifications subject to change without notice C MMUNICATI NS All Rights Reserved See website for latest revision Not intended for life support applications Getting started with the 400AP Router continued Configuring the router continued Fie E iew Hi Bookmarks T H 10 x D Janus 4004P x We Janus 400AP Router Configuration Administrator Logout Change Password Cellular Configuration Router Port rurwarus wiaynostics Administration Firmwar
14. t Start Stop e This is a port number or range of port numbers to forward Destination IP e The new destination of the session after the port forward Typically this is the internal machine like 192 168 1 100 Description or Rule e A description of this rule This is just for documentation If you are not entering any port forwards at this time you may move on If you are entering any port forwards click the Add button and fill in the information check the Enabled box and then click Save Terminus 400AP LCR User Guide JAO7 UM_LCR Page11 Rev A01 Date 10 23 14 JAN U S REMOTE Copyright 2014 Janus Remote Communications Specifications subject to change without notice C MMUNICATI NS bases All Rights Reserved See website for latest revision Not intended for life support applications Getting started with the 400AP Router continued Configuring the router continued Step 8 Go to the Administration tab and scroll down to find the available settings e 192 168 2 1 8080 router index login_success True v tig Router Reboot is REQUIRED to apply new settings Reboot Now Settings Allow Remote Management via WAN Configuration Portal Port Number 8080 Router Configuration Revert to Defaults Janus Remote Communications 1970 If you are not adjusting the default host port number you may move on Otherwise you can change it click Save and continue Step 9 Now w
15. te If no bootable media is found the processor will boot into SAM BA mode The green LED will not illuminate h Factory Default Condition 400AP Powered Red LED is illuminated 1 Apply Power wait for the red LED to Summary illuminate During runtime after the red light has illuminated 2 Press and hold the Mode button until you can use this to reset all fields to the factory default the red LED blinks Release Mode Note You must wait until the red light is on otherwise you may enter SAM BA mode on accident SAM BA Mode Condition 400AP powered 1 Press Mode button Summary 2 Apply power to device or use Reset Processor boots into SAM BA mode 3 Depress Mode after the Green LED and the green LED illuminates illuminates Note Using this method to enter SAM BA mode is supported when using the factory supplied bootloader that evaluates the Mode button If NAND flash has been erased this functionality will not exist The 400AP application note uploading files into flash explains how to write the bootloader to flash LED Indicators GPIO controlled LED stack In the 400AP Router configuration they give some quick feedback on the status of the device Red LED State Description Permanently OFF Router is unpowered Permanently ON Router is powered Yellow LED State Description Permanently OFF Cellular radio is off Permanently ON call is active Fast Blinking 0 5 sec on 0 5 sec off Unreg
16. uring the router continued Step 6 Go to the Router tab and scroll down to find the available settings rE Edit View History Bookmarks Tools Help 0 x Janus 4004P x 4 192 168 2 1 8080 router index login_success True Select a router profile to configure Available Configurations Basic Profile 1 Profile Name Basic Profile 1 IP Address 192 168 2 1 IP Subnet Mask 255 255 255 0 HostName 400AP DHCP Setup DHCPEnabled M Starting IP Address 192 168 2 10 Max Number of Users 10 In this example we are leaving the base IP address and hostname default with DHCP set If you are not changing this you may move on otherwise set to the desired information lf you changed the information click Save and continue Step 7 Go to the Port Forwards tab and scroll down to find the available settings There will not be any entries by default Incoming Incoming Destination Destination Destination Enabled Protocol Port Start Port Stop IP Address Port Start Port Stop Rule Description m TCP 1 6 192 168 1 1 1 6 Test Enable Port Forward e if checked the rule is enabled If unchecked the rule has no effect and is disabled Protocol e If TCP is selected then only TCP traffic will be forwarded to the destination host e If UDP is selected then only UDP traffic will be forwarded to the destination host e If Both is selected then both TCP and UDP traffic will be forwarded to the destination host Por
Download Pdf Manuals
Related Search