GV300 User manual V1.09
Contents
1. 7 TERMS AND ABBREVIATIONS eec 7 PARTIO ae 9 DESCRIPTION OF 16 PIN CONNECTIONS 2 10 GV300 USER CABLE COLOUR DEFINITION eene 11 GPS ANTENNA SPECIFICATION 15 ELECTRICAL CHARACTERISTICS OF IGNITION DETECTION 16 ELECTRICAL CHARACTERISTICS OF THE DIGITAL INPUTS 16 ELECTRICAL CHARACTERISTICS OF DDIGITAL 5 18 DEFINITION OF DEVICE STATUS AND LED nenne 20 01 sia GV300 User manual FIGURE 1 FIGURE 2 FIGURE 3 FIGURE 4 FIGURE 5 FIGURE 6 FIGURE 7 FIGURE 8 FIGURE 9 FIGURE 10 FIGURE 11 FIGURE 12 FIGURE 13 FIGURE 14 FIGURE 15 FIGURE 16 FIGURE 17 FIGURE 18 Figure Index APPEARANCE GV Popp pU 8 THE 16 PIN CONNECTOR ON THE 00 10 Sign dU 12 E 12 SIM CARD INSTALLATION cx css csissereunasentscinbsestepsigansieiaqutaeaountsdintsautegeagentsvvasents 13 BACKUP BATTERY INSTALLATION eese eee eene nnn nennen 13 unos 14 GPS ANTENNA Cas i 14 TYPICAL POWER CONNEGTIGOIN 15 TYPICALIGNITION DETECTION PME PII P PUDE2. Optional 14 3 6 1 GPS Antenna Specificato 15 3 7 Power Contectigh e Me e De 15 3 8 uni HO 16 3 9 16 3 10 Aumnlog 5 48 17 3 11 Wigital Outputs 8f 29 5 18 Device Status LED a ANA o eoo rr 19 3 13 Serial Port 20 3 13 1 Connect With 22 24 2 2 21 4 300 22 4 1 CALI T 22 4 2 P I T T He 22 4 3 227 4 4 XC 22 01 3 GV3ODUermmal TABLE 1 TABLE 2 TABLE 3 TABLE 4 TABLE 5 TABLE 6 TABLE 7 TABLE 8 TABLE 9 TABLE 10 Table Index GV300 PROTOCOL REFERENCE ertet
3. 16 TYPICAL DIGITAL INPUT CONNECTION 9 28 eere 17 TYPICAL ANALOG INPUT CONNECTION eene rennen nennen nnne 17 DIGITAL OUTPUT INTERNAL DRIVE 18 TYPICAL CONNECTION WITH RELAY 55 5 2 18 TYPICAL CONNECTION WITETWED 5 19 GV300 LED ON THE 6 19 TYPICAL CONNECTION WITH RS232 2 22222 2 21 GV300 CONNECTION WITH GARMIN GPS SET eene 2l 01 5 GV300 User manual a 0 Revision History 1 01 2011 8 19 Owen Feng First review Leo Lei Vivi Zhu Add picture of new case V3 1 03 2011 09 27 Owen Feng Add Switch ON the Backup Battery Add new feature output with PTC over current protection 2011 10 10 Add page 7 add notes of FCC 2011 12 16 Add battery off position note 1 06 2012 04 10 Owen Feng 1 Change analog input range Me 2 Add user cable colour definition Add certification info Add uart Garmin connection 1 09 2014 01 26 Ricker Liu 1 gt Change user cable colour definition 2 Repair the relay connection figure 01 6 GV300 User manual SOLUTIONS 1 Introduction The GV300 15 a powerful GPS locator designed for vehicle or asset tracking It has sup
4. er and internal battery voltage is lower OFF note 2 than 3 35 V No external power and internal battery voltage is Slow flashing below 3 5 V External power in and internal battery is charging Fast flashing External power and internal battery is fully charged Note 1 GSM LED cannot be configured 2 GPS LED and PWR LED can be configured to turn off after a period of time using the configuration tool 3 Fast flashing is about 60ms 780ms OFF 4 Slow flashing is about 60ms ON 1940ms OFF 3 13 Serial Port UART Interface There are two lines dedicated to the Serial Port UART interface TXD and RXD TXD RXD are standard RS232 signal 01 20 2 GV3ODUermmal Female DB 9 Figure 17 Typical Connection with RS232 Port 3 13 1 Connect With Garmin GPS Set GV300 can communicate with Garmin GPS Set The following typical connection is using Queclink AG100 cable Figure 18 GV300 connection with Garmin GPS set Note GV300 some version maybe connects with Garmin GPS set by Garmin FMIIO FMIIS cable please consult with Queclink for detail information TRACGV300UMOOI 21 GV300 User manual 4 GV300 certification 4 1 FCC certification GV300 has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules This device complies with part 15B part 22 and part 24 of the FCC r
5. erior receiver sensitivity fast TTFF Time to First Fix supports Dual Band GSM frequencies 850 1900 its location can be monitored in real time or be periodically tracked by a backend server or other specified terminals The GV300 has multiple input output interfaces that can be used for monitoring or controlling external devices Based on the integrated Track protocol the GV300 can communicate with a backend server through the GPRS GSM network to transfer reports of Emergency geo fence boundary crossings low backup battery or scheduled GPS position as well as many other useful functions Users can also use GV300 to monitor the status of a vehicle and control the vehicle by its external relay output System Integrators can easily setup their tracking systems based on the full featured Track protocol 1 1 Reference Table 1 GV300 Protocol Reference GV300 Track Air Interface Protocol The air protocol interface between GV300 and backend server 1 2 Terms and Abbreviations Table 2 Terms and Abbreviations Abbreviation Description AGND Analog Ground AIN Analog Input DIN Digital Input DOUT Digital Output ND Ground MIC Microphone RXD Receive Data TXD Transmit Data SPKN Speaker Negative SPKP Speaker Positive 01 7 iy Gv3OUermaud HIS 2 Product Overview 2 1 Check Part List Before starting check all the following items have been included with your GV300 If anything 1s missi
6. ges rights reserved in the event of grant of a patent or the registration of a utility model or design specification supplied herein are subject to change without notice at any time Copyright Shanghai Queclink Wireless Solutions Co Ltd 2011 01 2 GV300User manual NI RETE SE soLutions Contents CO Me Tu 3 C VISION TSO MEET T TT 6 MM GUION tm 7 1 1 eiecit ps 7 1 2 Terms and ZO OC 7 5 m m 9 2d 9 2 2 quake 9 2 3 PIU TENERE 10 2 4 GV OO Dser able _______ __ _ 11 ME omm mE 12 3 c 12 222 Closing the 7 12 3 3 Installing a SIM 13 3 4 Installing the Internal Backup 13 219 Switch ON the Backup 7 9 Me 14 3 6 Installing the External GPS Antenna
7. iy JEL GSM GPRS GPS Tracker aV User Manual Application Notes 000 001 Revision 1 09 CDY IPELESS amp sales eddywireless com GV300 Operating Vollage DC B 32V FCC ID YOD FCC ID YOD GV300 C 0678 Doer omes ari ENTERA IMEI 862170013909997 THIS SIDE TOWARDS SKY GV300 User manual aa Document Title GV300 User Manual Document Control ID 000 001 General Notes Queclink offers this information as a service to its customers to support application and engineering efforts that use the products designed by Queclink The information provided is based upon requirements specifically provided to Queclink by the customers Queclink has not undertaken any independent search for additional relevant information including any information that may be in the customer s possession Furthermore system validation of this product designed by Queclink within a larger electronic system remains the responsibility of the customer or the customer s system integrator All specifications supplied herein are subject to change Copyright This document contains proprietary technical information which 15 the property of Queclink Limited copying of this document and giving it to others and the using or communication of the contents thereof are forbidden without express authority Offenders are liable to the payment of dama
8. m drain current is 150 mA Each output has the built in over current and recovery PTC fuse Figure 13 Digital Output Internal Drive Circuit Table 9 Electrical Characteristics of Digital Outputs Logical State Electrical Characteristics Enable lt 1 5V 150mA Disable Open drain Power line Figure 14 Typical Connection with Relay 01 18 GV300 User manual RETEST SOLUTIONS 8 to 32Vdc Resistor Figure 15 Typical Connection with LED Note 1 OUTI will latch the output state during reset 2 Many modern relays come with a flyback diode pre installed internal to the relay itself If the relay has this diode insure the proper relay polarity connected is used If this diode is not internal it should be added externally A common diode such as a IN4004 will work in most circumstances 3 12 Device Status LED GSM LED GPS LED POWER LED Figure 16 GV300 LED on the Case TRACGV300UMO001 19 GV300 User manual 2 Table 10 Definition of Device status and LED LED status GSM Device is searching GSM network Fast flashing notel Note3 Device has registered to GSM network Slow flashing Note4 SIM card needs pin code to unlock GPS GPS chip is powered off note 2 GPS sends no data or data format error Slow flashing GPS chip 16 searching GPS info Fast flashing GPS chip has gotten GPS info PWR No external pow
9. n Color Color AD1 IN3 OUTI White Black Green or Pink Gray Black 01 11 GV300 User manual SSARETESS ESE A 3 Getting Started 3 1 Opening the Case Figure 3 Opening the Case Insert the triangular pry opener into the gap of the case as shown below push the opener up until the case unsnapped 3 2 Closing the Case Figure 4 Closing the Case Place the cover on the bottom in the position as shown in the following figure Slide the cover against the direction of the arrow until it snapped TRACGV300UMOOI 12 GV 300 User manual IRELESB SOLUTIONS 3 3 Installing a SIM Card Open the case and ensure the unit is not powered unplug the 16Pin cable and switch the internal battery to off position Slide the holder right to open the SIM card Insert the SIM card into the holder as shown below with the gold colored contact area facing down taking care to align the cut mark Close the SIM card holder Close the case Figure 5 SIM Card Installation 3 4 Installing the Internal Backup Battery ets ag 102 10629 B 947 0 au Figure 6 Backup Battery Installation There is an internal backup Li ion battery TRACGV300UMOOI 13 GV300 3 5 Switch ON the Backup Battery To use the GV300 backup battery the switch must be at the ON position Switch on the case and ON OFF position are shown below Backup battery swi
10. ng please contact your supplier Figure 1 Appearance of GV300 TRACGV300UMOOI 8 GV 300 User manual 2 2 Parts List Table 3 Part List Name Picture GV300 Locator User Cable Extend Cable Optional GPS Antenna Optional DATA_CABLE_M Optional TRACGV300UMOOI 80 49 26 mm IRELESB SOLUTIONS 2 3 Interface Definition The GV300 has a 16 PIN interface connector It contains the connections for power I O RS232 microphone speaker etc The sequence and definition of the 16PIN connector are shown in following figure a 82522323 EN 8171615 C d mii nt 2 2955522 9 Figure 2 The 16 PIN connector on the GV300 Table 4 Description of 16 PIN Connections Comment MICP Single end 2 2 2k microphone internal bias AGND Analog ground Ignition input positive trigger UART RXD RS232 UART TXD RS232 6 GND Power and digital ground Open drain 150mA max 8 OUT2 Open drain 150mA max EARP l l Differential output 320hm 1 4w speaker External DC power input 8 32V Digital input negative trigger Digital input negative trigger Open drain 150mA max with latch circuit Multifunction input analog or digital input 0 16V 16 Analog input 0 3 16v 5 ADI IN3 01 10 GV300 User manua 2 4 GV300 User Cable Colour Table 5 GV300 User Cable Colour definition Definition PIN Definitio
11. tch Figure 7 Switch and ON OFF position Note 1 The switch must be on the OFF position when shipped on an aircraft 2 When the switch is on the OFF position the battery cannot be charged or discharged 3 6 Installing the External GPS Antenna Optional There is a SMA GPS antenna connector on GV300 The GV300 will automatically detect and use an external antenna when connected GPS Connector Figure 8 GPS Antenna of GV300 TRACGV300UMOOI 14 GV300 User manua 3 6 1 GPS Antenna Specification Table 6 GPS Antenna Specification GPS antenna Frequency 1575 42MHz Bandwidth gt 5 7 Beam width 2120 deg Supply voltage 2 7V 3 3V Polarization RHCP Gain Passive OdBi min Active 15dB Impedance 500 VSWR Noise figure 99 3 7 Power Connection PWR PINI2 GND PINO are the power input pins The input voltage range for this device is from 8V to 32V The device is designed to be installed in vehicles that operate on 12V or 24V systems without the need for external transformers 8V 32V Figure 9 Typical Power Connection 01 15 G300 Usermanual 3 8 Ignition Detection Table 7 Electrical Characteristics of Ignition Detection Electrical State 5 0V to 32V to or Open Vehicle switch Start 4th position Run 3rd posltlon Accesories 2nd position Off 1st position Fig
12. ules Operation is subject to the following two conditions 1 this device may not cause harmful interference 2 this device must accept any interference including interference that may cause undesired operation Power Output is ERP for Part 22 and EIRP for Part 24 End users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance GV300 FCC IDENTIFIER YQD GV300 4 2 European CE 0678 GV300 has been manufactured in accordance with the European R amp TTE directive This product complies with the European CE LVD Low Voltage Directive 2006 95 EC standard IEC 60950 1 2005 2nd Edition A1 2009 EN 60950 1 2006 A11 2009 A1 2010 4 3 certification GV300 has been awarded PTCRB certification PTCRB certification is an industry operator requirement needed to be met in order to sell GSM cellular communication products in the North American market 4 4 Anatel certification GV300 has been homologated tested Brazil and is ANATELG APPROVED for all installations in Brazil Anatel ID 0633 12 7782 TRACGV300UMO001 22
13. ure 10 Typical Ignition Detection IGN Pin3 is used for ignition detection It is strongly recommended to connect this pin to ignition key RUN position as shown up An alternative to connecting to the ignition switch is to find a non permanent power source that is only available when the vehicle is running For example the power source for the FM radio IGN signal can be configured to start transmitting information to backend server when ignition is on and enter power saving mode when ignition 15 off There are three general purpose digital inputs on GV300 They are all negative trigger 3 9 Digital Inputs Table 8 Electrical Characteristics of the digital inputs Logical State Electrical Characteristics Active OV to 0 8V Inactive The following diagram shows the recommended connection of a digital input TRACGV300UMO001 16 GV300 User manual Panic Button Figure 11 Typical Digital Input Connection 3 10 Analog Inputs There two analog inputs on GV300 the analog input voltage range is from 0 to 16V following diagram shows the recommended connection Figure 12 Typical Analog Input Connection Note PIN 15 is an multifunction pin it can be configured as a digital input or an analog input 01 17 GV300 User manual 3 11 Digital Outputs There are three digital outputs on GV300 are of open drain type and the maximu
Download Pdf Manuals
Related Search