IMPORTANT SAFETY INSTRUCTIONS DANGER
Contents
1. Cooking zone positioning Bio Deactivation of cooking zones Select the cooking zone you wish to switch off Press the corresponding button a dot lights up at the bottom right of the power level indicator Press the key to set the level to 0 To switch off instantly hold the zone selection button for 3 seconds The cooking zone switches off and the residual heat indicator H lights up Control panel lock This function locks the controls to prevent accidental switching on of the hob To activate the control panel lock function switch on the hob and hold button or the Automatic function Eco Booster button where present for three seconds an acoustic signal and a luminous indicator next to the padlock signal activation The control panel is locked except for the deactivation function To deactivate the control panel lock repeat the activation procedure The luminous dot goes off and the hob is active again The presence of water liquid spilled from pots or any objects resting on the button below the symbol can accidentally activate or deactivate the control panel lock function GB15 Timer mim The timer can be used to set cooking time for a maximum of 99 minutes 1 hour and 39 minutes for all cooking zones Lt ut Select the cooking zone to be used with the timer an illuminated dot appears to the bottom right hand side of the heat setting indicator on the O display press the button with the clock symbol the2. Belgium only 400 V 2N Holland only a m gt zL m z zL I Ss mt t L Ils p holley A a Pe be RR O SR t FF O un ae Nes LL l F Nd N N2 n e Important Based on the wiring diagram see figure either keep or remove the metal jumpers between the screws on the terminal block L1 L2 and N1 N2 If the cable is provided see the connection instructions attached to the cable Make sure all six screws on the terminal block are tightened after connecting the cables Example a present left or removed right See the wiring diagram for details the jumpers can be between L1 L2 and between N1 N2 GB14 Connect the yellow green earth wire to the terminal with the symbol This wire must be longer than the other wires 1 Remove the terminal block cover A undoing the screw and inserting the cover in the terminal block hinge B 2 Insert the power cable in the cable clamp and connect the wires to the terminal block as indicated in the connection diagram located near it 3 Secure the power cable with the cable clamp 4 Close the cover C and screw it on the terminal block with the previously removed screw Each time the power is connected the hob performs an automatic check for a few seconds If the hob already has a power cable follow the instructions attached to the cable Connect the appliance to the power supply by means of a multipole switch with minimum cont
3. be made by children without supervision A separator panel not supplied must be installed in the compartment under the appliance If the surface is cracked switch off the appliance to avoid the possibility of electric shock The appliance is not intended to be operated by means of an external timer or separate remote control system Unattended cooking on a hob with fat or oil can be dangerous and may result in fire NEVER try to extinguish a fire with water but switch off the appliance and then cover flame e g with a lid or a fire blanket Danger of fire do not store items on the cooking surfaces Do not use steam cleaners Metallic objects such as knives forks spoons and lids should not be placed on the hob surface since they can get hot After use switch off the hob element by its control and do not rely on the pan detector GB12 SAFEGUARDING THE ENVIRONMENT eal Disposal of packing The packing material is 100 recyclable and marked with the recycling symbol Ly The various parts of the packing must not be dispersed in the environment but disposed of in compliance with local regulations Disposal This appliance is marked in conformity with European Directive 2002 96 EC on Waste Electrical and Electronic Equipment WEEE By ensuring that this appliance is correctly disposed of the user can help prevent potentially negative consequences for the environment and the health of people The symbol Bt on the applianc
4. off Special functions Some models have special functions Fast boil function Booster This function only present on some cooking zones makes it possible to exploit the hob s maximum power for example to bring water to the boil very quickly To activate the function press the button until P appears on the display After 10 minutes use of the booster function the appliance automatically sets the zone to level 9 Automatic function The function automatically sets the power level to maintain a light boil Activate this function after bringing to the boil pressing first of all the cooking zone button followed by button Eco Booster With the hob on and the cooking zone selected press button E to activate the function The hob automatically activates a cycle that allows you to bring water to the boil and then keep it simmering with reduced energy consumption compared to the normal booster function The function is only provided for the two cooking zones identified by the symbol Z Demo Mode This hob is equipped with a demo mode which allows you to interact with the control panel without activating the corresponding cooking zones The activation and deactivation procedure must be carried out within 60 seconds of the appliance being connected to the power supply in the home To activate the demo mode hold the two external cooking zone selection buttons at the same time for at least 5 seconds dE appears on
5. IMPORTANT SAFETY INSTRUCTIONS YOUR SAFETY AND THAT OF OTHERS IS VERY IMPORTANT This manual and the appliance itself provide important safety messages to be read and always observed A This is the danger symbol regarding safety warning of potential risks to users and others All safety messages will be preceded by the danger symbol and the following words A DANGER Indicates a hazardous situation which if not avoided will result in serious injury MATAN h eg Indicates a hazardous situation which if not avoided could cause serious injury All messages relevant to safety specify the potential risk to which they refer and indicate how to reduce the risk of injury damage and electric shocks due to incorrect use of the appliance Make sure to comply with the following The appliance must be disconnected from the power supply before carrying out any installation operation Installation and maintenance must be carried out by a specialised technician in compliance with the manufacturer s instructions and the local safety regulations in force Do not repair or replace any part of the appliance unless specifically stated in the user manual The appliance must be earthed The power cable must be long enough for connecting the appliance fitted in the cabinet to the power supply For installation to comply with the current safety regulations an omnipolar switch with minimum contact gap of 3mm is required Do not use multi sockets
6. act gap of 3mm INSTRUCTIONS FOR USE ce Control Panel Description Control panel On Off Timer Control panel lock aa k C a G i A ge mjo o ajg olo INDUCTION alg l Cooking zone controls and corresponding display On Off Timer Control panel lock NS Automatic function AUTOMATIC FUNCTION S Ecobooster function oO IN DUC TION Oo 9909 98999 Cooking zone controls and corresponding display Switching the hob ON OFF To switch the hob on press the T button for approx 2 seconds until the cooking zone displays light up To switch off press the same button until the displays switch off All the cooking zones are deactivated If the hob has been in use the residual heat indicator H remains lit until the cooking zones have cooled down If within 10 seconds of switching on no function is selected the hob switches off automatically Switching on and adjusting cooking zones Once the hob is switched on and the pan is positioned on the chosen cooking zone select the zone using the corresponding button the display shows level 5 i T Each cooking zone has various power levels adjustable with the buttons going from 1 Selected cooking zone indication min power to 9 max power Some cooking zones have a fast boil function Booster shown on the display with the letter P Power indicator display
7. e or the accompanying documentation indicates that this product should not be treated as domestic waste but must be taken to an appropriate collection point for recycling WEEE Energy saving For optimum results it is advisable to Use pots and pans with bottom width equal to that of the cooking zone Only use flat bottomed pots and pans When possible keep pot lids on during cooking Use a pressure cooker to to save even more energy and time Place the pot in the middle of the cooking zone marked on the hob DECLARATION OF CONFORMITY C This appliance intended to come into contact with food products complies with Regulation C no 1935 2004 and has been designed manufactured and marketed in conformity with the safety requirements of Low Voltage Directive 2006 95 EC replacing 73 23 EEC as amended and protection requirements of EMC Directive 2004 108 EC BEFORE USE Opposite Place the pot on the required cooking zone before switching the hob on IMPORTANT The cooking zones will not switch on if pots are not the right size Only use pots bearing the symbol INDUCTION SYSTEM Figure EXISTING POTS AND PANS Use a magnet to check if the pot is suitable for the induction hob pots and pans are unsuitable if not magnetically detectable _ Make sure pots have a smooth bottom otherwise they could scratch the hob Check dishes Never place hot pots or pans on the surface of the hob s control panel This could re
8. n set the desired cooking time using the buttons and of the timer function see figure After a few seconds the timer begins the countdown an illuminated dot is visible next to the zone for which the timer has been activated Once the set time has elapsed an acoustic signal sounds and the cooking zone switches off automatically To deactivate the timer press the button until the display shows 0 0 or hold the button with the clock symbol for at least 3 seconds To set the timer for another zone repeat the points above The timer display always shows the timer for the selected zone or the shortest timer To change or switch off the timer press the zone selection button for the timer in question Control panel warnings Residual heat indicator The hob is fitted with a residual heat indicator for each cooking zone These indicators alert the user when cooking zones are still hot f the display showsH the cooking zone is still hot If the residual heat indicator of a given cooking zone is lit that zone can be used for example to keep a dish warm or to melt butter When the cooking zone cools down the display goes off Incorrect or missing pot indicator If you are using a pot that is not suitable not correctly positioned or not of the correct dimensions for your induction hob the message no pot will Li appear in the display see figure at side If no pot is detected within 60 seconds the hob switches
9. n the display consult the following table for instructions If the hob cannot be switched off after using it disconnect it from the power supply ERROR CODE DESCRIPTION POSSIBLE CAUSES ERROR ELIMINATION The control panel switches off p i The internal temperature of electronic Wait for the hob to cool down 81 C82 because of excessively high i o parts is too high before using it again temperatures The sensor detects a discrepancy Disconnect the hob from the F42 or F43 The connection voltage is wrong between the appliance voltage and mains and check the electrical that of the mains supply connection F12 F21 F25 F36 F37 F40 F47 F56 F58 F60 Call the After Sales Service and specify the error code NOISES MADE BY THE HOB Induction hobs can make whistling or crackling sounds during normal operation these actually come from the pots and pans as a result of the characteristics of the bottoms for example bottoms made of several layers of material or uneven bottoms These noises vary depending on the pots and pans used and the amount of food they contain and are not indicative of a defect of any kind In addition the induction hob is equipped with an internal cooling system to control the temperature of electronic parts as a result during operation and for several minutes after the hob has been switched off the noise of the cooling fan will be audible This is perfectly normal and indeed e
10. ng maintaining a light boil cooking and grilling for a medium period of time 10 20 g saut ing grilling minutes preheating accessories 4 5 Cooking st Sang Ideal for stewing maintaining a gentle boil cooking for a long period of time Creaming pasta grilling Medium power 4 Ideal for long cooking recipes rice sauces roasts fish with liquids e g water wines broth milk Cooking simmering creaming pasta thickening creaming Ideal for long cooking recipes less than a litre in volume rice sauces roasts fish with liquids e g 23 water wines broth milk i2 Ideal for softening butter gently melting chocolate thawing small products and keeping just cooked O 7 Melting defrosting keeping food warm e g sauces soups minestrone i food warm creaming Ideal for keeping just cooked food warm for creaming risottos and for keeping serving dishes warm 1 with induction suitable accessory OFF zero Support surface Hob in stand by or off mode possible end of cooking residual heat indicated by an H power NOTE When making quick cook foods that require perfect heat distribution e g pancakes on the 28 cm double cooking zone where present use pans no greater than 24 cm in diameter For delicate cooking for example melting chocolate or butter use the smaller diameter single zones GB18
11. on the underside of the appliance ELECTRICAL CONNECTION Disconnect the appliance from the power supply A WARNING Installation must be carried out by qualified personnel who know the current safety and installation regulations The manufacturer dedines all liability for injury to persons or animals and for damage to property resulting from failure to observe the regulations provided in this chapter The power cable must be long enough to allow the hob to be removed from the worktop Make sure the voltage specified on the dataplate located on the bottom of the appliance is the same as that of the home Connection to the terminal block For the electrical connection use an HOSRR F cable as specified in the table below i i 230 240 V Australia onl Wires Number x size 400V3N 30V a r eee y 20V 3x4mm 3 Li Li LI 230 240 V 3 X 4mm Australia only ts me a ITL ie T lcs s jr pR E i Je 230V3 4x15 mm I I lE Le BBB IRS 2 3 400V3N 5x1 5 mm ibe MJS O MS Lan ae Sn a 1 Jie 400V2N 4x15 mm N2 N2 N2 400 V 2N 230 V3
12. or extension cords Do not pull the appliance s power cable The electrical parts must not be accessible to the user after installation The appliance is designed solely for domestic use for cooking food No other use is permitted e g heating rooms The Manufacturer declines any liability for inappropriate use or incorrect setting of the controls The appliance and its accessible parts become hot during use Care should be taken to avoid touching heating elements Children less than 8 years old shall be kept away unless continuously supervised The accessible parts can become very hot during use Children must be kept away from the appliance and watched over to ensure they do not play with it Do not touch the appliance heating elements during and after use Do not allow the appliance to come into contact with cloths or other flammable materials until all the components have cooled sufficiently Do not place flammable materials on or near the appliance Overheated oils and fats catch fire easily Pay attention when cooking food products rich in fat and oil This appliance can be used by children aged from 8 years and above and persons with reduced physical sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand hazards involved Children shall not play with the appliance Cleaning and user maintenance shall not
13. ssential for proper functioning of the appliance AFTER SALES SERVICE Before contacting the After sales Service 1 See if you can solve the problem yourself with the help of the Troubleshooting guide 2 Switch the appliance off and then on again it to see if the problem has been eliminated If the problem persists after the above checks contact the nearest After Sales Service Always specify e abrief description of the fault the product type and exact model the Service number the number after the word Service on the rating plate located under the appliance on the metal plate your full address your telephone number SAAK 0000 000 00000 If any repairs are required contact an authorised After Sales Service Centre to ensure the use of original spare parts and correct repairs Spare parts are available for 10 years GB17 POWER LEVEL TABLE Power level Type of cooking Level use indicating cooking experience and habits Ideal for rapidly increasing the temperature of food to fast boiling in the case of water or rapidly Boost Fast heating heating cooking liquids 8 9 Frying boiling Ideal for browning starting to cook frying deep frozen products fast boiling 78 Browning saut ing boiling Ideal for saut ing maintaining a lively boil cooking and grilling for a short period of time 5 10 grilling minutes High power Browning cooking stewing Ideal for saut i
14. sult in damage RECOMMENDED POT BOTTOM WIDTHS 17 cm min 28 cm max 12 cm min 18 cm max 15cm min 21cm ma 10 cm min 14 5 cm max GB13 INSTALLATION After unpacking the product check for any damage during transport In case of problems contact the dealer or the After Sales Service For built in dimensions and installation instruction see the pictures in page 2 PREPARING THE CABINET FOR FITTING Install a separator panel under WARNING the hob The lower part of the product must not be accessible after installation Donot fit the separator panel if an undertop oven is installed min 5mm min 20 mm min 5 mm e The distance between the underside of the appliance and the separator panel must respect the dimensions given in the figure e Inorder to ensure the correct operation of the product do not obstruct the minimum required clearance between the hob and the top of the unit min 5 mm Ifan undertop oven is installed make sure the oven is equipped with a cooling system Do not install the hob above a dishwasher or washing machine so that the electronic circuits do not come into contact with steam or moisture which could damage them In the case of flush mounted installation call the After Sales Service to request assembly of screws kit 4801 211 00112 To remove the hob use a screwdriver not provided to prise off the perimeter clips
15. the central display You can now explore the control panel functions The Lock and Unlock function is active also in Demo Mode To deactivate Demo mode repeat the procedure remembering first of all to disconnect the hob from the mains and then reconnectit carrying out the procedure within 60 seconds of connection 5 Sec Activation deactivation of the acoustic signal After switching the hob on press and hold the button and the outermost selector button on the right simultaneously for at least five seconds control panel lock CLEANING Donot use steam cleaners A WARNING Before cleaning make sure the cooking zones are switched off and that the residual heat indicator H is not displayed IMPORTANT Do not use abrasive sponges or scouring pads Their use could eventually ruin the glass After each use clean the hob when it is cool to remove any deposits and stains due to food residuals Sugar or foods with a high sugar content damage the hob and must be immediately removed Salt sugar and sand could scratch the glass surface Use a soft cloth absorbent kitchen paper or a specific hob cleaner follow the Manufacturer s instructions TROUBLESHOOTING GUIDE Read and follow the instructions given in the section Instructions for use Check that the electricity supply has not been shut off Dry the hob thoroughly after cleaning it If when the hob is switched on alphanumeric codes appear o
Download Pdf Manuals
Related Search