Getting Started with SADiE6 Software
Contents
1. SADIE Getting Started with SADiE6 Software Congratulations for purchasing SADiE6 software the finest Professional Audio Editing system in the world This short guide aims to help you install the software and get started on your first editing project Contents The SADIE6 software pack contains e The SADIE6 installation CD this includes installers for the software and for other software options plus documentation for the SADiE hardware platforms in PDF format and if ordered with a dongle the dongle key file e The SADiE6 USB memory stick optional containing the same files as the CD but in a handy USB stick format e Your SADiE6 USB Dongle Key optional which is used to authorise the SADiE6 software e This booklet Note If this pack is included with a Turnkey system where the software is already installed to the PC you can skip the next few sections but you may wish to read from page 5 which gives a quick start guide to the software To distinguish the USB memory stick from the dongle as both are USB devices the memory stick has pale blue round cover with a 6 logo on one side the dongle is a darker blue DO NOT INSERT THE DONGLE YET Pull on the chain to remove the memory stick from its circular cover in order to reveal its USB port Dongle Memory Stick Installing the Software The first step is to run the software installer NOTE If you have previously been usin2. will affect only those Clips selected 13 If you want to select more than one Clip either SHIFT select multiple Clips or rubber band them as you would do sections of text in a word processor To de select ALL clips just click in a blank area of the Playlist Note EDL ENTRIES don t be alarmed when you see the word entry This just means one of the clips in the EDL each clip is actually an entry in the edit decision list Renaming Clips within your EDL Right click over the Clip itself and select Edit Entry Name Razor Cut Ehe RAZOR CUT button on the main Playlist Tools toolbar or default Hot Key F5 in the Playlist divides the Clip s under the current time cursor into two at that point Ez also have the option of using the scissors to make cuts Whereas the RAZOR button always cuts at the current time cursor and across all Streams unless you have disabled them for cutting when you press the SCISSORS button on the main Playlist Tools toolbar the mouse pointer will change into a scissors icon with a cross to show the target point You can then make a freehand cut anywhere in the Playlist which will cut only the clip over which you clicked useful if you can see exactly where to cut from the waveform profile Cut Copy amp Paste These techniques can be used to remove move and add EDL Clips in the same way that text is manipulated in a word processor Note when cutting or copying
3. When moving around the Playlist to access different parts of your EDL you may want to change which part or how much of it is displayed These scrollbars work in the same way as any word processor You can also use the Hot Key default SHIFT Left Right Arrow to zoom in and out Playing Back the Audio Using the Time bar As well as using the transport controls and space bar for playing amp stopping SADIE you can also use the mouse in the time bar at the top of the Playlist window e Double click in the white time bar area to start playback immediately from that point e Single click anywhere in the time bar to stop playback e Single click in the time bar when playback is stopped to locate the current time cursor to that point e Keep double clicking in the time bar to play from that point to find something you are looking for You can set up SADIE so that you can double click anywhere in the Playlist rather than just the time bar to start and stop even on a clip itself Do this via the Setup window Manipulating Clips EDL Entries in the Playlist You can view the clips in the EDL as either blocks representing bits of tape or as profiles a graphic waveform display that accurately represents the original audio You manipulate Clip s by first clicking on it them so that they turn red Whatever you do next drag CTRL Drag to copy cut copy paste level change default Hot Key L Remove Gap delete etc
4. 17 Stream control buttons Mouse time display Current time cursor Stereo Clip on a stereo Stream 12 The Playlist The Playlist is a window that is used to create and manipulate your EDL Edit Decision List An EDL or in SADIE is basically like a word processor document you can cut copy paste add clips of audio amp save the file When you first start a new Project SADIE will open a Playlist window containing an empty EDL named after the Project You can then build up the EDL by recording directly into it or by pasting in Clips from the Clipstore and editing You can save this EDL as another within the same project if you wish by selecting Save As under the File dropdown menu All the EDLs in your Project can be opened via the Project Window Best Practice save your Project via Save Project under the Project dropdown menu This saves ALL the EDLs and indeed all other components at the same time This way you don t have to save each component separately and reduces the risk of forgetting to save anything Alternatively of course you may want open an existing Project and do further work on that EDL As SADIE is 100 non destructive editing you can work on an EDL made years before and simply continue to manipulate the edits Scrolling amp Zooming Click or Drag box Click either side of Zoom Zoom hold down for coarse box to scroll one Out In for fine scrolling window s width scrolling
5. Clips they are in fact loaded into a temporary store called the Paste Buffer This buffer is what is then pasted into the EDL at the point you wish So you can move Clips by Cutting amp Pasting them in somewhere else and you can repeat them by copying them and pasting the copy somewhere else This paste buffer continues to keep its contents until you cut or copy another selection or close SADIE Thus you can continue to paste the same content many times by just pasting again and again These tools are on the Playlist PASTE toolbar but you can also use the standard Windows Hot Keys CTRL X CTRL C CTRL V Cutting Removing Clips from the EDL LS ISelect the Entry Entries as described above then Press CUT ENTRIES TO PASTE BUFFER Copying EDL Clips to the Paste Buffer T the Entry Entries then Press COPY ENTRIES TO PASTE BUFFER Pasting clips into the EDL NOTE The Paste Buffer first needs to be loaded from cutting or copying EDL Clips as described above If it is not loaded its button picture will appear faint s Wilrress LOAD PASTE BUFFER TO CURSOR When you move your mouse pointer or cursor over the Playlist Streams you will see that it has changed to a reel of tape with a cross indicating where the in point of the Clip Clips will be positioned The mouse time display will give you the exact EDL time Click to paste the Clip Clips into the Playlist You can also paste by right c
6. Customising SADIE There are several things you can set up in SADIE to make it look and work the way you want Once these settings are set up you won t have to change them again even after you close down SADIE Basically these settings fall into three areas TEMPLATES There are two kinds of template you can set up one for the Playlist and one for the mixer The template is just a way of telling SADIE how many streams you want in your Playlist and whether they are to be stereo or mono Also included in the Playlist templates are any locators you may want pre set up and the sample rate For those wanting to make CDs there is a PQ stream that can be shown this is included in your template USER SETTINGS These belong to a specific user i e the one who logs onto SADIE at the beginning of a session The settings file or ini file is automatically loaded up as you log on and includes your favourite system settings such as default crossfades hot keys etc You change these from the SETUP window As you make a change the file is saved automatically 28 One of the settings however is the use of templates mentioned above This setting tells SADIE how you want to use the templates i e each time you create a new Playlist or mixer or that you don t want to use them at all i e stick with the default 16 mono streams amp 16 mono faders THE DESKTOP This is just a small file that you can set up from within SADIE that determ
7. and Mixer each named after this Project name These will start off in a default state and after use in the normal way can be saved closed and re opened as part of the Project Once you are working in SADIE the best way to save your work is by selecting Save Project from the Project drop down menu at the top of the screen This saves ALL your work i e all the EDLs Mixers Clipstores within your project in one go The Project Management Window You can also open the Project Management window at any time This is normally minimised at the bottom of your screen From within this window you can manipulate the project and create new EDLs Mixers amp Clipstores You can also import EDLs from other projects 27 Monty Funk 1 CERERE 12 07 10 10 08 EMM SADIEGWin7 Clusers sadieiwinfidocuments sadielprojects Monty Fun on Package 1 is the piece about ferrets Package 2 is Helen s piece when finished Package 3 is the music montage use the montage micer to play ft and wel bounce t down before putting it in the main programme Tip If you cannot find a window eg the Mixer because it is hidden or has been closed open the Project Management window Then just double click on the icon representing that window and it will open o create a new component EDL Mixer or Clipstore just click on the icon and give it a name A you need to import a component from another project then just click on this icon
8. comprise the basics EDLs Clipstores amp Mixers as many of these as you wish and can also include any other Windows document Word Docs PDFs pictures etc which may be of use in your work On top of this the Project Folder normally contains all the audio you use within a Project Although audio can be referenced to external locations it is advisable to keep it in the Project Folder and there is a function to do this so that copying and backing up becomes a simple Drag amp Drop process under Windows SADiE s Projects are created saved amp loaded again either as you first launch SADIE or from within the application itself EDL Edit Decision List An EDL is a file created using SADiE s Playlist window It shows the Clips joined together as you want them with all their basic levels cross fades automation data names and so on This file is the one we edit with the various tools of the Playlist window together with a number of hot keys and the hardware controllers if you are using them and is the window in which we spend most of our time editing and compiling The EDL basically tells SADIE which parts of which raw audio tracks to play in which order at which level etc It has to be saved if you are to use it again and is normally saved within the Project CLIP A Clip is a reference to all or any part of a raw track of audio It is the Clips that are edited and manipulated within
9. current time display and typing a new value e After positioning the cursor by scrubbing with the Edit section of the transport controls perhaps scrubbing to picture to find a visual synch point 15 Grouping Clips Any number of Clips may be grouped together They will be redrawn as a single block in the Playlist This may be for convenience of display for repeated operations to the same group or to avoid accidentally undoing edits You can rename a group and store it in a Clipstore so a heavily edited piece can be stored as if it were a single Clip Be select the Clips you want to group then press GROUP SELECTED EDL ENTRIES Hot Key G Groups may be further grouped with other Clips or other groups and a hierarchy is formed R any time you can break a group back down into its component parts by selecting it and pressing the UNGROUP button Hot Key U Undo amp Redo ad Gs Pressing UNDO can reverse the last change that you made to the EDL Press UNDO again to reverse the change before that and so on stepping back through the history of your actions The maximum number of undo levels is set in the Setup window and can be up to 50 REDO steps you back the other way after using undo You can of course use the standard Windows Hot Keys CTRL Z Undo and CTRL Y Redo Changing the Layout of Streams You may want more or fewer Streams than your current Playlist contains There is no limit to the number of Streams
10. fader at any time it will go into write mode for the period you hold the fader When you let go again the fader will auto return back to its original level This allows you to build up a basic mix and then go back and tweak it at any time by just touching the faders This of course works better with the SADiE Fader Panel as it has touch sensitive motorised faders but the function works perfectly well with just the mouse There is no need to save anything else other than the project as the automation data is now recorded into the clips which are on the EDL which gets saved with the project You can record pan EQ dynamics and VST automation in exactly the same way just click amp hold pan controls whilst playing The automation data has been written into the clips but you can switch off automation at any time by just hitting the automation yellow button again The data is still there just not commanding the faders to move You can turn it on and off as you wish Snapshot Automation B G his is a brilliant function if you want to change the level of a number of clips at the same time You simply select the clips you want click on the little camera button on the automation toolbar change the level of the fader that controls the stream the selected clips are on then click the camera again 24 The clips are set at the new level EQs amp Dynamics If you want to change the EQ of a stream you can do that within the mixer
11. folder ready for you to drag amp drop into the EDL EIU F D Cayo Track 0907 WAY These audio files are now part of your project and are once copied physically located in your project folder The audio will be represented as Source Tracks within the Clipstore Simply drag amp drop them into the Playlist window to start editing them Best Practice unless you really want to always choose Copy amp Import rather than just Import Source Tracks By Copy amp Importing the audio is actually duplicated and copied from its original location into your Project Folder so that you don t need the original drive to always be attached and keeps all your Project material together Copy amp Import also performs a Sample Rate Convert so that the imported audio matches the sample rate of your EDL Ingesting Audio 3 Importing Audio CDs You can import audio from a CD into SADIE 6 easily and quickly Here s how to do it 1 Insert your audio CD into the PC s CD drive 2 Open the Clipstore as with other importing 3 Right Click in within the Clipstore and select Import CD Tracks 4 All the tracks on the CD will appear you may have to wait for a few seconds for the CD to be read 5 All the audio tracks default to being selected so you may want to click on Deselect All and then tick the tracks you want You may also wish to click on Set Base Name and enter the name of the CD if
12. it doesn t contain CD Text SADIE will then title the audio in the Source Tracks Folder by that name 6 You can right click on a track in the list to audition it 7 Click the Start button and off it goes When it has finished importing close the CD Import window and remove the CD from the PC 8 You can now drag and drop the audio you want into your Playlist 10 Track 01 Track 02 Track 03 Track 04 Track 05 Track 06 Track 07 Track 06 Track 09 Track 10 Track 11 Track 12 Track 13 Track 14 Track 15 Track 16 Track 17 Track 13 IL iL oO oO E oO iL O Eg iL iL iL O O O O iL CD Import is actually a background task you can in fact close the CD Import window once you have started importing and carry on working within the EDL Note from within the Clipstore just drag and drop individual audio files not the CD icon itself SADIE Projects and Project Folders A Project in SADIE is the way to organise all the audio EDLs and other components of your SADIE work in one place This is normally achieved through SADiE s Project Manager window which simply manipulates the folder on the PC drive that is created when you create a new project This Project Folder contains all the components of your project EDLs Mixers Clipstores and all the audio you have ingested by either recording copying ripping a CD or internally bouncing It makes sense to work this
13. the linear parts of the Playlist where you place your clips building up the EDL that makes your production You can add or remove streams as necessary The streams have their own sets of controls that affect the clips on those streams such as mute solo record enable etc Streams can be mono stereo or multi track and can be changed whenever desired added to or removed by right clicking in the Stream control area S Best Practice select or create a stereo Stream to record stereo material so that the two channels remain in sync no matter how you manipulate them in SADIE How the audio on a Stream is played out of SADIE is determined by the relevant Stream s mixer channel this can determine the pan balance level EQ dynamics and so forth MIXER The Mixer is where you route audio around the SADIE system and generally balance the mix of your work Each Stream on the Playlist will normally have a mixer strip in the Mixer assigned to it enables you to control the level and pan position of all the Clips on that particular Stream Each of these mixer strips has its own EQ dynamics compression etc and auxiliary sends to the outside world hardware permitting as well as other tools including Direct X and VST plug ins these are all just inserted onto mixer strips Many of the mixer operations levels panning EQ aux sends can be automated so that your movements can be remembered and played back A Mixer is one of t
14. unaffected and places the new track into the current Clipstore PC Disk makes a bounce recording directly to your PC s hard disk The bottom section allows you to choose Bounce in non real time If this is selected the bounce will be performed as quickly as possible but will not be audible The other two options allow you to turn off automation and or the mixer for the bounce Press Start The process will start and during the bounce the ball icon in the Bounce button will bounce Be careful not to click on the time line in the Playlist or press transport buttons you will stop the bounce 31 Special Bounce Functions Multi Bounce with MULTI selected as the source for the bounce every entry in the EDL will be re recorded as a separate audio file on the audio drive If you want a group of entries to become a single audio track then simply group the entries a Group Entry is treated as 1 entry You must have Autotake selected the new tracks will be automatically named using this function Reverse bounce The reverse option in the Bounce window allows you to make a backwards copy of an EDL entry or entries Note also that right mouse clicking over an entry will initiate the Bounce window with Reverse enabled Otherwise the Bounce window works in the normal way Reverse cannot be used in conjunction with Resample Varispeed or Timemod Note that the Bounce records the Output of the mixer including any level changes or proce
15. up by that Clips duration If you paste a Clip with Slip enabled all subsequent Clips will move out of the way by the pasted Clips duration If you Remove Gap on a selected Clip with Slip Right enabled it will butt up accordingly bringing the rest of you EDL with it This is fundamental to radio programme making where you are not tied to a time code without it you would have to keep selecting all Clips in the EDL to the right of the clip you are moving and ensure they are all selected so that things don t go out of sync later To Enable Slip click on the Slip Enable icon in the Slip toolbar and MAKE SURE either Slip Left or Slip Right is also selected once you have first chosen Slip Left Right it will remain the selection each time you enable Slip so you only have to this once Generally Slip Right is the option to choose for radio and Podcasting work N Tip if you have the SADiE BBC Hot Keys loaded the Hot Key for Slip is S this will speed up your workflow enormously Snap To Cursor This is a very useful tool for synching up Clips Right click over the Clip you want to move and select Snap In Point to Current Time The Clip will jump to a new position with its in point on the current time cursor This is useful e On the fly whilst listening to music to run alongside speech A voice Clip can be snapped to cursor during playback e After positioning the current time cursor by double clicking on the
16. way as you then just have one folder which can be copied or moved around any Windows system for backing up or moving to other SADiE machines Note a project s EDL could refer to audio files not in the project folder but we need to ensure that this isn t the case by following the procedures for Copying and Importing audio files into our Project Folders in this guide Creating a New Project in SADiE Launch SADIE and select New Project in the Project Startup Menu that appears 11 it eee Monty Funk 1 Sample A ate 4a1kHz l Frame Fate 25s zl Document onty Funk 1 Browse Create Cancel Or from within SADIE if it is already running choose New Project from the Project drop down menu Best Practice Assuming SADIE has been setup appropriately the location you chose for creating your Project at the creation stage will be the place everything Project components and audio goes You can also setup SADIE to always look in a certain location for creating new Projects and this will be the place it first looks to open existing Projects NOTE It is possible to set SADIE to record audio to a different location though this is clearly not advisable in most circumstances as you could end up with Project components and audio on different drives Using the Playlist Mono clip on a Mone Stream E Monty Funk edl Modified a e SB mos r oS gi E ma q Fa pn 4A Piskan 47
17. SADIE never the original audio There can be many Clips in an EDL each referring to either different audio tracks different parts of the same track or even many clips referring to the same part of a track all playing back at the same time if you wish Clips can be duplicated many times without duplicating the original audio track CLIPSTORE The Clipstore component of a project contains clips that refer to the raw audio tracks on the hard drive s There is always a Source Tracks Folder within the project s main Clipstore this contains clips that refer to entire audio tracks so that they can be dragged into your Playlist and edited Other clips can be put into the Clipstore that have already been edited in the Playlist for repetitive use or use in the future A Clipstore is one of the components of a project and extra Clipstores can be imported form other Projects EDL ENTRY A Clip becomes an EDL entry when you place it into an EDL basically a SADiE EDL just sees a list of entries but displays them to us as Clips for easy editing and manipulation So when you see the term Entry referred to it simply means the Clip within the EDL AUDIO TRACK An audio track is the actual audio as it was originally ingested recorded imported ripped form CD or internally bounced into the project and put onto the hard disk You never edit this audio itself just the Clips that refer to it STREAM The streams are
18. Setup Window from the View menu We recommend that you use hardware with an ASIO driver SADIE is able use WDM drivers also but performance is much better with an ASIO driver Licences To run SADIE your software installation must be authorised The first time you install SADIE on a PC it will operate in trial mode for 30 days If you have the USB Dongle key you should install it now If not skip this section and move to Requesting a Licence Installing the Dongle The CD or USB memory stick that you installed the software from should still be inserted Don t insert the Dongle just yet If you are installing from the CD go back to the main menu of the CD wizard and click on Install a Dongle If you are installing from a USB memory stick navigate to the root directory of the stick and run the program SADiE_Dongle_Installer exe by double clicking on it Once again the software installation is automatic You may need to press enter to move through the installer A driver and a key file for your dongle will be installed to your PC At the end of the dongle installation you will be prompted to restart the PC There are two installers running to install the dongle so please wait until the full process is complete On re starting the PC connect the dongle to a USB port The installation of the driver for the dongle will be completed and you will be able to start SADIE The first plug and play of t
19. a Playlist may contain only to the number of Clips the system hardware can play back at the same time You can also merge any number of Streams so that they can be controlled together and reduced in height to save display space 16 Merge Into Stereo Stream Menge Selected Strearns Rename Stream Insert 2 Mono Streams After Insert Stereo Stream After Remove Stream Automatically Add Remove Mixer Strips Stream vertical zoom Selected Streams vertical zoom Automation Display Show hide stream and groups lists Horizontal PPMs Stereo Streams can be added to the Playlist or created by merging two mono Streams When you record onto a stereo Stream you actually create a stereo Audio Track whereas recording onto two mono Streams actually produces a two channel Audio Track Right click over the small Stream control buttons to e Merge Into Stereo Stream merges two adjacent Streams e Insert Streams will insert a pair of streams e Remove Stream will remove the one you clicked on and renumber them e Right clicking on merged Streams gives you options to change how they are displayed and to ungroup them again Editing SADIE provides a fast and intuitive interface for editing With stereo material the two channels are always edited simultaneously There are a number of ways of editing within SADiE For general editing the PLAYLIST EDITING mode provides a fast way of accessing the ins outs amp
20. ant and it will do just that keeping the original pitch These three processes will change the output of SADIE that is the whole EDL will change If you just want to process a single clip or group of clips then set up this process as you want it and Bounce Down the selection through the Bounce Window see notes Make sure you then switch off the process afterwards right click to the left of the process otherwise it will still be processing Project Management In SADIE the work we do is managed within a Project Basically this is a folder on your PC s hard disk that contains all the EDLs Mixers and Clipstores this folder to ALSO hold all the audio Each time you save you are updating these files When you first log into SADiE you are presented with a window as shown below 26 Open Monty Funk 1 Open an existing Project Create a new Project Restore a Project With this window you can either 1 Open the Project that was last worked on the current Project 2 Open an existing Project that you have previously saved 3 Create and name a new Project 4 Restore a Project that has been backed up to a storage device When you create a new Project 1 If SADIE detects more than one audio disk connected you will be asked which disk you want to use to record to 2 Then you will be asked to give the Project a name and the Project window will open SADIE will have created a new EDL Clipstore
21. e the file is updated automatically no need to save anything There are many settings you can make but there are a few that are crucial for efficient working Here are some essential suggestions If you have created templates for the Playlist amp Mixer see above then you tell SADIE to use them here in the setting window Double click on Project Management about half way down on the left side of the window On the right you will see three options Select Use Specified Templates and click on the select buttons chose the templates you saved earlier 29 E SADIE settings for user SADIEGWin7 j gt a pS Topics Sen ee Templates Audio Native Drivers sync Pre Post Roll E This t ates are used when a Playlist efe Trim a Mixer oO Clipstore nplat I cer creation time Undo Default Cross Fades a 9 Pin Channels i MIDI Controllers l Change s Transport Controls Auto Conform P Management Mixer i ates Change da PQ Settings l Hotkey setup Clip Details a Ed Conversion Bounce _ Use template sample rate and frame rate Trim Window Setup We suggest that you select trim window on the left side and make sure of the following Make sure Trim Slips Follow Playlist Slip is UN TICKED Bouncing Clips may be permanently grouped together by re recording them internally as a new track of audio The bounce button is on the Playlist Toolbar You may choos
22. e request file has been generated and saved to disk The license request file should now be e mailed to either your system administrator or directly to SADIE You may either 1 Send the e mail directly in which case SADIE will attemptto send itto the e mail address supplied below 2 Send the e mail yourself at a later time e mail address jiicense sadie com Send e mail directly Send the e mail myself Having saved this the file should be emailed to license sadie com SADIE will ask if you want to do this automatically or manually You will need an email client to be installed on your PC for the automatic operation to work Note If nothing happens when you press Send e mail directly then your email client is not working and so you should resort to the manual method To Send the e mail myself find the ARQ file it will usually be in your Documents folder and will be named something like Sadie6_yourcompany_yourpc arq then attach it to an email and send it to license sadie com The SADIE office will process this request as soon as possible and you will be sent a Licence Response file in the form of a ARP file which will usually include your company name and the name of the PC to which it is licensed To Install the Licence Response Once the Licence Response file has been sent back to you from the Help menu choose Manage Licences then from the next dialog box choose Install Licence Response Br
23. e to bounce entries down for a number of reasons e Convenience You want the mixed or processed result to always appear as a single EDL entry or you don t want to bother with setting the Mixer or Automation to process the required entries every time you play the EDL e There is not enough DSP power available to carry out the processing you require in real time and or play the number of simultaneous Entries you require Process the necessary entries through the Mixer and bounce down your selection Then you can use the processed versions in the full EDL e First select the clips in the EDL You normally re record these clips through the mixer so check the mixer balance is correct 30 Click on the bounce icon E open the Bounce Window You need to enter a name for the recording The first section of this window serves the same purpose as the Record tab of the Transport window Next tick Selected Clips in the Source section The Source section tells Bounce what to re record Complete EDL or Selected Streams are the other possibilities We must choose in the Destination section what s going to happen to the new track after re recording Stream tells Bounce to put it into the same EDL on streams specified in the pop up list Auto replace source clips only works in conjunction with Stream when this is ticked at the end of the bounce process the source clips are deleted Clipstore leaves the Playlist
24. earlier Clips fade out and alters the length of the later Clips fade in to match the earlier Clips fade out This results in a matched cross fade between the two Clips With two Clips in the window selecting either fade automatically selects them both Then the whole cross fade between two Clips can be moved easily in relation to the audio When you are happy with the adjustments WRITE BACK what you have done Writing Back the Finished Edit The Trim Editor is actually a temporary area for adjusting edits Once done the edit and any other changes you have made needs to be written back to a Playlist which will then be updated E you have loaded the Trim Editor from a Playlist press WRITE BACK TO SOURCE EDL to update that Playlist Other Trim Editor tools Ehhe four SNAPSHOT buttons allow you to store and recall four different arrangements of the Clips in the Trim Editor so you can compare different attempts at an edit Click once to take a snapshot and the button will turn blue to show it has a snap stored After making adjustments click on the button again to return the Trim Editor to the stored snap The button of the displayed snap will turn red To overwrite a button with a new snap hold Ctrl while clicking on it 21 Clipstore Every piece of audio on the hard disk is represented by a clip which can be accessed via the Clipstore When you make a recording within your project or otherwise ingest material a clip wi
25. eech say in the Playlist you can trim the join precisely merging the letters together For example if the result of your cut is So this cut saves us time and money and the joined up Clips are between this and saves you could end up with two s s By merging one s into the other you effectively get a more natural So thi saves us money This elision in speech has been crafted more naturally and therefore far more convincing that a straight butt edit assuming this is appropriate for your interviewers way of speaking Once you are happy with the many things you can do in the Trim Editor you then Write Back the edited version to the Playlist Opening the Trim Editor Select the Clips you want to load into the Trim Editor either side of the edit in question They do not have to be on the same Stream Press the OPEN TRIM EDITOR button on the Playlist toolbar A Trim Editor window will now appear containing the Clips that you loaded 19 In the example above two Clips have been loaded from the Playlist The main difference in the way the Clips are displayed here is that because each is drawn on a different line the profile of the whole Audio Track from which it comes can be shown The parts that are being used and will be played as Playlist Clips are in green or red when selected and the parts not being used are shown in grey This makes it possible to see what you are losing as wel
26. either for a whole stream or you can automate it to affect as much of it as you wish Above each channel strip you should see at least one little box which can contain a process To the left of the faders is a palate containing the processes lt Auxiliary send Low pass EQ High cut Low shelf EQ Band pass EQ bell High shelf EQ High Pass EQ Low cut 4 compressor Expander Gate M5 Decoder The last three items are used to drag across and insert new Mixer strips These can be mono without pan mono with pan or stereo strips You simply click amp hold on the process you want from the process palate and drag amp drop it into the little box above the fader The process is now active and waiting for you to use it You can drag amp drop more processes into these boxes If you need to see more just make the mixer larger Tip hold your mouse over the process palate and a message will tell you which process you are about to select Inline Process Compressor Inline Process High pass filter Low cut Inline Process Band pass bell Inline Process Auxiliary send Processing is being applied to Stream 4 To change the settings of a particular process once you have dropped it into your mixer strip simply click on it and its parameters will appear for use to manipulate If you want to automate the movements of th
27. ese processes you need to switch off the automation disable button in the top right of each process Then with the mixer automation switched on yellow button remember you can change the processes and these changes will be recorded 25 Bypass Process Disable Name automation Aux Send You can also send a level from the channel to the outside world via the aux send control Drag amp drop the aux process to a spare slot above the fader you want to send Click on the process and select the output to be a spare output of your SADIE You can then use this control to send a level from the stream to an external effects unit for example Deleting Processes To delete a process simply RIGHT CLICK on the process in the channel strip and select Delete Process Sample Rate Conversion Varispeed amp Timemod W is a very powerful feature of SADIE If you need to change the sample rate varispeed or timestretch an EDL you can do it with these processes Firstly open the Process window with this icon You will then have a representation of an effects rack Select the Sample Rate Converter from the toolbar at the top and drag it onto the rack You can then change the input amp output sample rates seee BUGS ob I J OONOO a the Varispeed and Timemod also In Timemod you can select a clip or number of clips and it will tell you the length of your selection you can then just type the new length you w
28. fades of individual clips on the Playlist However for the fine tuning of edits the TRIM EDITOR provides a way of accurately trimming between two clips With both methods you can manipulate the cross fades between Clips as well as Clip levels 17 The Trim Editor however provides an extremely powerful tool for de umming your work designing music edits and creating powerful cross fades that seem impossible at first Playlist Editing Mode Whenever you make a razor or scissors cut to divide an EDL Clip into two you will actually create a new fade out and fade in at that point In Playlist Editing mode when a Clip is selected in the Playlist it will change to a waveform profile and its in out amp fade points can be adjusted BB wivate Playlist Editing mode with this button on the Playlist toolbar 00 00 05 00 000 10 00 15 Ono anatomy A wearing fi Then with the mouse select the Clip you want to adjust its graphic profile will be shown in red Depending where you point the mouse over the Clip a handy little graphic at the mouse pointer will appear to tell you which bits of the Clip are going to move as follows Fades amp Cross fades There are four more mouse symbols which let you increase the length of the fades at the in and out points by dragging out the start or the end of each fade Overlapping them will create cross fades Hold the keyboard Ctrl key as you move the mouse over
29. g an earlier version of the SADIE software on this computer it is best to uninstall the old version first Go to the Start button Control Panel Add Remove Programs or Programs Uninstall a Program then select the older SADIE program and uninstall it Uninstalling the SADiE software does not alter data settings hotkeys or licences 1 Insert your software CD or the USB memory stick You may need to wait a moment while your computer is dealing with this 2 If installing from CD a menu will appear You will be asked to select your platform between Native and SADiE Hardware Platform and then press the Install button If installing from Memory Stick Navigate to the Software directory of the USB memory stick and run SADiE6_installer exe by double clicking on it 3 Follow the instructions on screen There will be a few messages with some configuration choices but if in doubt press enter to continue through the installer 4 Once the installer has finished you will see a SADiE6 icon on your desktop Double click on the icon to start the SADIE software Running SADiE6 Audio Hardware The first time you run SADIE if you are running without SADIE hardware you will see a message about the selection of audio hardware At the time of this first start SADIE chooses some hardware automatically but you can choose from available hardware in SADiE s Native Drivers setup page which can be found in the
30. have associated with it a Channel Strip fader in the mixer You use this fader to control the level of all the audio on that particular stream Where you have stereo streams you would normally have a stereo fader these are single faders that control both sides of the stereo stream together but you could have two mono faders panned left amp right if you prefer To change a pair of mono faders into a stereo fader simply RIGHT CLICK over one of the faders amp choose Make Stereo If you want to change the pan position of a mono stream to the centre Double click over the little pan control at the top of the fader then click on the tiny c button on the right this centres the pan control Levels amp Panning 23 Mudge Drag Centre Now you have your faders matching the Playlist you are able to control the levels of audio as they pass from the Playlist through the Mixer to the outside world To change the level simply click on the fader controlling the stream you want with the mouse hold it and move it up amp down To change the pan position within the stereo mix click amp hold the little pan button at the top of the fader If you wish you can double click on the pan control and move the little slider type in a figure double click on the little number use the amp keys plus a number click away from the slider and this new position is set for that stream To reset the fader to zero i e no change click on t
31. he components of a Project and saved amp loaded with that Project HOT KEYS These are user defined keyboard shortcuts to make your workflow faster You can create a Hot Key for virtually any function within SADIE There are default ones and user defined ones and you can load them up as desired from the Environment gt Hotkeys menu If you select Load you will find some pre defined ones and selecting the SADIE 5 using BB2 set will enable the BBC friendly key set referred to in this training guide Ingesting Audio 1 Recording with SADiE To make a recording in SADiE you need to have set up a few things first Once set up they will remain this way even when you exit SADIE unless you change them again You can do this via the Transport Window 00 04 15 09_00 3 LELG V Autotake Retake V Remain _ Properties Generally the quick key for this is F10 but you can also open it with the icon in the toolbar In this window click on the SETUP button at the bottom and you will go to SADiE s Audio Settings window In here you should change the audio source to either digital AES or analogue depending on where the source audio is coming In the Setup window you can also change whether SADIE 6 is using ASIO hardware internal Windows Media drivers or its own hardware if you have it connected see earlier in this section If you have selected Analogue as your input then you may need to change t
32. he dongle may take a while and you should be able to watch its progress in the Windows plug and play wizard If starting SADIE doesn t find the dongle wait just a while longer Subsequent re insertion of the dongle will be quicker The dongle will need to be present to start and run SADIE on that PC To be able to use SADIE on other PCs run the same procedure of a installing SADiE software and b installing the Dongle NOTE To install the Dongle on a PC you will need both the Dongle and its installer and its individual key file the Dongle alone is not enough Therefore it s important to keep the Dongle installer files safe Once the Dongle is correctly installed to a PC however just plugging in the Dongle will authorise SADiE operation that PC Lost dongles We must stress that it s important to insure your dongle for the full amount of the software that s licensed to it If a dongle is missing to replace it will cost the price of the dongle plus a full SADIE licence If a dongle is broken or faulty its licences can be moved to a new dongle once the faulty one has been returned to the factory We can provide users who have support contracts with temporary licences to bridge a period while a faulty dongle is being replaced or repaired Having installed the dongle there is no need to Request a Licence and so you can skip the next section Requesting a Licence If you haven t purchased a dongle SADIE is authorised to r
33. he little fader lock button This also locks the fader you can unlock it again amp the fader will stay put Automation Now the really clever bit is to be able to automate the movements of the fades amp pans as the EDL is played back through the Playlist Fla do this you need to enable the Automation function with this icon normally to the left of the faders When this button is active it lights up bright yellow to warn you every move you now make with the faders pans EQs Dynamics VSTs will be recorded into the clips on the Playlist Consequently if you then move a clip around or cut copy paste it the automation data will go with it There is no problem therefore in doing some automation and then continuing editing If you want to see what the automation looks like in your EDL switch on the Show All Automation Data button at the top left of the Playlist You will also then be able to manipulate it directly on the Playlist You will notice that when you first switch on automation there will be a little toolbar created with fader buttons and the red button will be active This is known as overwrite mode and when you move the fader it overwrites any fader automation data into the clips you are controlling When you stop playback the green button will be active This green button is auto update which means that the faders will playback according to how you first moved the faders but if you grab the
34. he sample rate at which SADIE will record the audio Make sure that this is the same as the rest of the audio within the project if possible NOTE If you have selected a digital input then when you hit the record button SADIE may ask you if you want the sample rate changed to reflect that of the digital source Always click yes if it asks you so that the profiles pictures of audio you see on screen will be properly matched Once this is set up close the settings window Back in the transport controls you should name the track of audio you are about to record Click to the right of where it says Track enter a name and then hit return V Best Practice though not essential to name your new recording SADIE will force you to do so unless Auto Take is enabled see below Auto Take you might want to turn on Auto Take This will put a number after the track name so you don t have to name each take With Auto Take enabled you could leave the name blank and SADIE will call the track Un named Track 01 and increment this number with each subsequent recording Next decide whether you want a mono or stereo recording For mono chose a mono stream to record on to choose a stereo stream for a stereo track 6 Click on the green record enable button in the stream controls to the left of the streams To get a level click on the pause button on the transport controls you may get a level as you hit the R button on
35. here you can find the audio you want to Copy amp Import On the left hand panel of this window double click on System to reveal My Computer and all the drives connected to it Import source track s GY system My Computer t Record Destinations E Proj EE 44K Songs BE bb taster sadic safeBB taster sadie AEROS AN Y_LONG VS BE v5 6 safe prj Aer tchenDi 19304 BE charie IRPLAI y 0025201 BE Espa a WJ BE fishys cat AIRPLAN VERHEADSIDI BE fishy ee RSPowerPack041601 BE Monty Funk 4 ah AIRPLA CUNSPowerPack040301 Be on TULES 4 BE The Laocoon jih ARPLA BE tracks T BE Webinar Finebox IC copy bin fa AF11 6 1 BATHROOM a API1 74 1 MOVEMENTS 3 Click on the Drive that contains the audio you want you may need to REFRESH if you have recently changed a drive or Flash Card to do this click on the little button at the bottom right of the window with the blue circular arrows Double click on this Drive to reveal the folders or files which shows up as little blue icons on the right hand side 4 If you want to audition your audio before copy and importing then select one of the little blue icons and click on the green arrow button next to the refresh button Select all the audio files you want by CONTROL or SHIFT clicking them and then click the OK button at the bottom of the window 5 The audio files you selected will then be COPIED and IMPORTED into your Source Tracks
36. ines the position of all the Windows It will also remember the icons toolbars you have set up their positions on the screen and the zoom settings you want Here s how you set it all up Log on to SADIE and create a new project In the Playlist window delete the Streams you don t want make them mono or stereo or create new Streams You do this by right clicking in the stream controls the area to the left of the streams themselves Next set the sample rate to the way you want it to be each time you create a new Playlist open the transport controls F10 then click on SETUP Next with the Playlist window the active window go to the File Menu and select Save Current Playlist As Template Call it something like Default Now go to the mixer and set it up how you wish If you made mono streams in the Playlist make the faders mono in the mixer and pan them to the centre Create stereo faders for the stereo streams again right click on the faders Next with the Mixer window the active window go to the File Menu and select Save Current Mixer As Template Also call it something like Default You now have two templates stored You now have to tell SADIE to use these templates when you create new Playlists or Mixers or when you create a new project SETTINGS This is very simple to achieve You go to the Set Up window under Windows menu In this window you can change the settings of SADIE As you make a chang
37. l as what you are keeping in which can aid editing decisions since the grey bits are always available to be pulled back into the green side of an edit point The Trim Editor has the following features in common with the Playlist e An EDL time bar which you can double click on to start and stop playback The current time cursor playback head is fixed in the middle of the window while the waveform profile of the audio scrolls past There is also a second time bar which shows time relative to the edit point e Scrollbars to move the display horizontally and vertically e Magnification buttons to zoom in or out of the display Greater magnification is possible here than in the Playlist Adjusting the Edit Once you have selected which parts to move simply click on them to move them as in the Playlist taTo hear the audio as it moves across the edit point press the audio scrub button Then click amp hold the clip and move the mouse left right to jog and up down to shuttle To hear the results of your adjustments you can e Start playback from any point in the Trim Editor s time bar double click e Use any one of the following preview buttons which have the advantage of playing you a pre set amount either side of the edit point and then returning the display to it 20 Plays up to the edit point plays through the edit point and plays from the edit point Note The play through preview is the one that lets you hear ho
38. licking the mouse at the point you want to past and select Paste 14 i essing the PASTE TO CURRENT TIME button will place the contents of the paste buffer into the Playlist at the current time Multiple Clips cut or copied from the EDL will be pasted back with the same time and Stream relationships between them NOTE To cancel pasting and drop the paste symbol from the mouse pointer press the button again or right click with the mouse To repeat one or more Clips either e Copy them and then paste them in at a new point as described above Or e Select them and then hold the Ctrl key whilst dragging a copy to the required position Remove Gap E is a useful tool on the main Playlist Tools toolbar for moving any selected Clip to the left so that it butts up to the previous Clip on that Stream The start of the selected Clip s fade in will be changed to coincide with the start of the preceding Clip s fade out Slip Keeping Everything in Sync Probably one of the most important functions of SADIE certainly for radio production is the Slip function When enabled this makes ALL clips to the right or left if desired of a selected Clip s move by the amount of that selected Clip Therefore if you select a Clip and move it everything that starts after the beginning of this Clip will move by that amount keeping all subsequent edits intact Similarly if you cut a selected Clip all subsequent Clips will move
39. ll appear in your Clipstore if you are actually recording it will also be drawn on the Playlist H Monty Funk1 cls EH You simply drag any clip from the Clipstore and drop it onto a stream on the Playlist If you need to get a piece of audio that wasn t recorded as part of your project it won t initially appear in your Clipstore however you can import audio at any time into your Clipstore by right clicking in the Clipstore This then takes you to a window where you can select a location then the folder then the specific audio track or tracks to import 22 When you then hit OK a clip will be drawn of the audio you chose and this clip will be put into your Clipstore The Mixer SADIE has a very powerful mixer to allow you to mix your work The normal procedure is to edit your clips on the Playlist and compile them into the right order positions Once you ve done that it s time to start mixing the sound Although the mixer is extremely powerful in normal operation there is basically nothing to set up Even if you create or take away streams from the Playlist the mixer will automatically create remove faders for each stream for you To manipulate the mixer open the mixer window which may be minimised at the bottom of the screen if it s not there open the project manager and double click on the mixer icon ae Audio unit Each stream on the Playlist will
40. owse to the arp file press OK and then SADIE will automatically install the option you have purchased If you wait until after the trial period has elapsed before requesting your licence you will not be able to open SADIE But you will be offered an option to allow you to make the licence request which follows the same procedure as above Getting Started with SADiE6 software SADiE6 Overview The following topics describe the fundamental functions in the SADIE6 software recording importing and editing There is further detailed explanation of these functions in the User manual itself which may duplicate some of this however it s recommended that you read these pages to help you master some of the simplest concepts and make your earliest tasks with SADIE run more smoothly and quickly You can view the SADiE User Manual either within the software itself by going to the Help menu and selecting Help on SADIiE6 or from the installation CD or the SADIE download page on our website where it is saved in PDF format as SADIE6 User Manual pdf Basic SADiE Terms amp Concepts PROJECT A Project is a folder located on a PC Drive where SADIE creates the files or project components that are used in the editing compilation and mixing process By managing the project you basically add remove name or update these components this is more easily done within SADIE itself via its Project Management Window The project components
41. ssing 32
42. the edit point 18 Mouse Graphic Click and Drag Start of the Fade in End of the Fade in a gt Start of the Fade out FY End of the Fade out If you want to alter the type of fade curve you can with Playlist editing still enabled simply hold down the ALT key Your mouse pointer will turn into a wavy line click and drag it to change the shape of the fade in or fade out That said greater flexibility for adjusting crossfades is possible with the Trim Editor Using the Trim Editor The Trim Editor is primarily intended for trimming the edit between two clips The Trim Editor is opened and loaded with the two Clips in question selected from the Playlist You then make precise and fine adjustments to the edit in the Trim Editor itself writing the result back to the Playlsit once you are happy As well as how tightly one Clip joins to another you can also adjust how they join for example how a piece of music fades down under a voice over how one piece of atmosphere cross fades into the next or how one word merges to the following one This timing and the quality of cross fade is crucial to the pace of the person speaking if you are editing speech the timing of the music if you are music editing or the flow of sound if you are merging atmospheres for sound design Because the Trim Editor is so precise you can easily trim between words parts of words letters and phonemes if you are speech editing Having cut out a chunk of sp
43. the stream controls depending on the set up of your SADIE When you are ready to start recording hit the RECORD button in the transport controls if you just hit the pause button again you will not be recording just playing though you can hit the RECORD button at any time to drop in to record whilst playing You will notice the Profiles pictures of the audio being created in the Playlist as you record Assuming you don t stop SADIE you can actually razor or scissor cut this audio rename it and move it from stream to stream select the Clip and CTRL Down Up Arrow whilst it is recording Recording Quick Guide Open the Transport Controls Hit SETUP confirm audio settings close Setup Window Name the Track to be recorded Arm the stream with the green LED button on stream controls Hit RECORD button Ingesting Audio 2 Importing Existing Material If you already have the material in the system because it already exists in another project exists on any other accessible Windows PC drive including the network or CD Rom was recorded onto a Compact Flash card using a portable recorder and you have it or a card reader attached then this audio can be Copied and Imported directly into your project folder This of course is very much faster than loading material in real time Here s the process 1 2 Open the Clipstore Select COPY AND IMPORT SOURCE TRACKS This will open a window w
44. un on a single computer You will need to request a licence send the licence request file to us by e mail then a licence response file will be sent back to you which unlocks SADIE on that PC It s not necessary to have email on the computer that is running SADIE the licence request is a file which can be copied to another computer that does have email To Request a Licence Go to the Help Menu in SADIE Choose the Manage Licences option If your licence has timed out you won t be able to start SADIE but you will see this next dialog box BD recto New Request ff instal License Response Select Create New Request SADIE License and Regi Pleae filin the following details Company name Gibert Sound i Firstname Humphrey Lastname Gilbert System name Humfiaptop E mail address humphrey gilbert gilbertsound com T Join the Prism Sound Recording Products mailing list To create a License Request please fil in the details above The system name can be any name that you choose but it should be unique Itis used to identify which computer your license is to be installed on if you have more than one computer create a License Request File which should be e mailed to license sadie com You will be asked for some registration details and then on pressing OK you will save a arq file the licence request file Remember where you have saved this The licens
45. w the edit will sound in the Playlist It also usefully resets the display to the edit point The up to and from previews are useful for determining which side of the edit unwanted sounds may be P review in context when pressed all previews will include the other audio in the source EDL as well as the current contents of the Trim Editor When you are happy with the adjustments WRITE BACK what you have done as described below Trim Editor Fades and Cross fades The fade lengths of Clips in the Trim Editor can be adjusted graphically with the mouse on the profile display as follows At each in out point there is actually a fade in or fade out however short and these fades have a start and an end Move the mouse pointer over the fade It will change to a double arrow You can then click amp hold to move the start of a fade to the left and the end of a fade to the right so lengthening the fade and setting it to where you want over the audio Fades are shown in lighter green on the profile and turn dark blue when selected to move The type of fade curve can be altered in the Clip Details window for the Entry by double clicking on the clip in question Once the fade out of one Clip overlaps with the fade in of the next Clip you have created a cross fade There is a useful tool available when there are two Clips in the Trim Editor e BB pircor amp Align Fades aligns the start of the later Clips fade in with the start of the
Download Pdf Manuals
Related Search