5 Operational modes - Products4Engineers
Contents
1. Deactivate Activate Response Deactivate Response Turn output 1 off Output 1 turned on BOutput 1 turned off urn output 5 on Turn output 5 aff Output 5 turned an Output 5 turned aff Turn output B atf utput turned on Output 6 turned aff T a a Figure 37 Configuration of output activation and deactivation messages Once the messages are configured you only need to send the entered text to perform the desired action EX If we want to activate output 4 we send gt Turn output 4 lt Output 4 turned It is possible to repeat the same message to perform simultaneously multiple actions to activate and also deactivate outputs Take into consideration that if you place reserved names to turn on outputs like for example DINPUTS DOUTPUTS the name of the used function will have no effect Avoid using reserved words in customized messages 4 1 24 Report of Digital Inputs When the status of one of the digital inputs is modified an SMS is generated automatically informing about the event In the case of a customized messages we can define the text that will be sent when the event occurs either when the input produces a transition from 0 to 1 or vice versa The message is determined by means of the GTS Configurator in the configuration screen of Digital Inputs in custom mode www exemys com Rev 2 3 0 Dic 2011 33 GTS User s Manual Exemys Dig2. WWW exemys com Rev 2 3 0 Dic 2011 Description The GTS is turning on the internal modem The GTS is subscribed to the GSM network and is ready to operate Sending and receiving of SMS GTS Configurator connected The GTS could not detect the presence of the SIM card or the corresponding PIN is not configured The level of the detected signal is not sufficient for a correct operation Verify if the antenna is correctly placed GTS User s Manual Exemys Chapter 3 3 GTS Configurator Software Installation and Utilization The GTS Configurator is the software provided with the product used to configure the GTS This application was developed with the easy to use philosophy and allows the configuration and monitoring of the GTS device The GTS Configurator can be installed on the following platforms Windows 98 SE ME Windows 2000 NT4 Windows XP and Windows Vista 3 1 1 Installation To install the GTS Configurator follow these steps e To begin the installation of the program insert the GTS CD and execute setup exe e A welcome screen will appear in the monitor follow the installation instruction that will request the necessary information to complete the installation Click on Next to continue e Destination folder Select the folder where the application program will be installed e Wait for the installation program to finish copying all the necessary files to your hard disk and press Finish to e
3. Generates a pulse at the output 30 Report Messages 31 4 1 19 SERIAL Sends messages entering by the serial port 31 4 1 20 AINPUT Reports the status of analog alarms 31 4 1 21 DINPUT Reports the change of digital inputs 32 Customized Messages 32 4 1 22 Messages to or from the Serial Port 32 4 1 23 Handling of digital outputs 32 4 1 24 Report of Digital Inputs 33 4 1 25 Report of analog inputs 34 5 Operational modes 35 GTS operational modes 35 5 1 1 Standard mode 35 5 1 2 Custom mode 35 Operational modes of the Serial Port 35 5 1 3 Transparent mode 35 5 1 4 commands mode 36 6 Practical Applications 37 Simple home automation 37 Centralized control 37 Inputs Outputs Serial Tunnel 38 A Troubleshooting quick guide 39 B Stream format in By Commands mode 40 C Character table and decimal equivalent 41 D Hysteresis operation 42 E Factory default values 44 www exemys com Rev 2 3 0 Dic 2011 4 GTS User s Manual Exemys Chapter 1 1 Introduction 1 1 About this manual 1 1 1 Purpose of this manual The purpose of this manual is to provide the instructions to quickly and simply install and operate the GTS The manual begins with a general description of the product followed by the instructions for the correct installation of the hardware Configuration and operation of the device are detailed later 1 1 2 Conventions terms and abbreviations Convention Description Gel Indicates a mandatory parameter
4. 4 1 20 AINPUT Reports the status of analog alarms When any of the analog inputs enters in an alarm status or leaves the status a message is generated informing about the situation Maximum minimum limits hysteresis and name are configured by the GTS Configurator for more information see in chapter 3 Analog Inputs in stander mode This message is only sent in Standard mode AINPUT Name Number Status Name assigned in the GTS From 0 to 10 characters Configurator Input number From 1 to n Number of inputs for its mod el Alarm status MAXIMUM ALARM www exemys com Rev 2 3 0 Dic 2011 31 GTS User s Manual Exemys MINIMUM ALARM ALARM NORMALIZED Ex lt AINPUT Tank 2 MAXIMUM ALARM 4 1 21 DINPUT Reports the change of digital inputs When any of the digital inputs modifies its status a change report is generated automatically that will be sent to the configured recipient phone numbers Each one of the inputs can be enabled independently for more details see in chapter 3 Digital Inputs in standards mode This message is only sent in Standard mode DINPUT Name Number Status Name assigned in the GTS From 0 to 10 characters Configurator Input number From 1 to n Number of inputs for its model Input status ON OFF lt INPUT Sensor 5 ON Ex Customized Messages Those messages that are only sent in Standard mode have their equivalent in custom mode Here is the detail of how
5. Indicates a parameter that can be used not according to the case lt gt Indicates that is a hexadecimal value Abbreviation Description GSM Global System for Mobile Communications SMS Short Message System PIN Personal Identification Number SIM Subscriber Identify Module ASCII American Standard Code for Information Interchange General Description of the Product GTS is a wireless communication device via SMS It has a serial communications port analog and digital inputs and digital outputs according to the model By means of the GTS it is possible to send and receive messages through the serial port to act on the outputs to know the status of inputs and other functionalities that are covered in this manual Models The current existing models are detailed and the characteristics of each one are explained 1 1 1 GTS2001 GTS2001 has a serial communications port 16 digital inputs and 14 digital outputs The distribution of input and output terminals is shown below WWW exemys com Rev 2 3 0 Dic 2011 5 GTS User s Manual Exemys IET ZEE ef 555555559 5 5 35355 35 5 5 5 0O e A QNO D a oa ow a 2 amp ao o U Figure 1 Terminals 1 to 18 D T woo tT oH Or DDG E M IST tog Z 55 58S 58 58S 58 558 zz 85 5 5 5 5 5 rc E gt Joc sa ys eS Em A wvnmiie Figure 2 Terminals 19 to 36 1 1 2 GTS300
6. 2 3 0 Dic 2011 2 GTS User s Manual Exemys 4 1 6 DELSENDER Deletes a phone number to the Filter List By Phone Number Deletes a number from the telephone list If Filter List by Phone number is enabled GTS will prevent from erasing the phone number of the telephone that is performing this configuration It works in both modes DELSENDER Telephone number Pass Telephone Telephone number that From 1 to 10 numeric number will be deleted characters Pas Password optional Configured password Ex gt DELSENDER 25485 pass lt Sender deleted 4 1 7 ENSENDER Enables Disables Filter List By Phone Number Enables Disables Filter List By Phone Number The list is only enabled if whoever requests the action is on the list It works in both modes ENSENDER Status of the list Pass Status of the Indicates if one wants to ON OFF list enable or disable the list Password optional Places password EX gt ENSENDER ON pass lt Senders list enabled Monitoring Messages By means of the SMS it is possible to know the GTS configuration and the status of the inputs 4 1 8 LISTALL Requests the configuration Requests the current configuration values It doesn t contain parameters It works in both modes Ex gt LISTALL lt SERIAL 9600 8 N E MODE STD 4 1 9 LISTRECIP Requests the recipients list Requests the current recipients list It doesn t contain parameters It work
7. except those indicated between lt gt STX 0x02 Command SYN 0x16 Data ETX 0x03 STX Indicates the beginning of the transmission of the stream and is hexadecimal 2 Command It is a number formed by two characters and can go from 00 to 99 SYN This is a parameter separator and is a 16 hexadecimal Data These are data corresponding to each command it can contain multiple parameters ETX Indicates the end of the transmission of the stream and is hexadecimal 3 Available command Command 12 Send and receive SMS Send Destination SYN 0x16 Message number Destination number The telephone number to whom you want to send the message SYN separator 16 hexadecimal Message Message to be sent with a maximum of 120 characters Receive Source number SYN 0x16 Time Stamp SYN 0x16 Message Source number The telephone number that generated the message SYN separator 16 hexadecimal Time Stamp Number that represents the seconds since 1970 Message Message received Ex Send 0x02 12 0x16 1152454545 lt 0 16 gt Test message 0x03 Ex Receive 0x02 12 0x16 1152454545 0x16 1524866981 0x16 Message 0x03 WWW exemys com Rev 2 3 0 Dic 2011 40 GTS User s Manual Exemys Appendix C Character table and decimal equivalent WOON AU C NJ E N xXEccCHUZaOUOzzrzxu rommuoooocmmg TM 5 gt ce Z O 5
8. 4 Establishing the Communication with the GTS To establish communication with the GTS first connect the serial cable with the RS232 port It is necessary for the cable to have the connection for the flow control pins see Installation serial connection To establish the connection select in the menu the G7S communication gt Connect option or press the button e When the communication is correctly established you will be able to observe on the screen information about the device a GTS Configurator GTS3002 i T3002 Serial Number 56 24 30 CONNECTED Firmware Wersion 1 3 0 Hardware version CONNECTED COM Figure 22 Main screen WWW exemys com Rev 2 3 0 Dic 2011 16 GTS User s Manual Exemys 3 1 5 Organization The GTS Configurator is divided into two main fundamental components on one side we find the monitoring tools that will let you visualize the GTS operation and status On the other side we have the configuration tools that permit to select and determine the device operation GTS Configurator GTS3002 File GIS Communications Monitor Configuration Help Figure 23 Organization of the GTS Configurator If the GTS Configurator finds an unknown model it will not enable the configuration and monitoring buttons In this case contact soporte exemys com to obtain the updated software version Monitoring 3 1 6 SMS Monitoring To enter the SMS Monitoring sc
9. exemys com Rev 2 3 0 Dic 2011 26 GTS User s Manual Exemys added O Pas Password optional Configured password EX gt ADDRECIP 1165845968 pass c Recipient added 4 1 3 DELRECIP Deletes an SMS recipient Deletes a phone number where the SMS will be sent It works in both modes DELRECIP phone number Pass Phone number that will be From 0 to 15 numeric characters deleted Pas Password optional Configured password EX gt DELRECIP 1165845968 pass lt Recipient deleted 4 1 4 Password configuration Configures the password that will be required for some messages It works in both modes CPASS New password Pass New password New password to be From 0 to 8 numeric characters entered Pas Password optional Configured password Ex gt CPASS newpass pass lt Password configured If you want to erase the password you have leave two spaces between CPASS and the configured password 4 1 5 ADDSENDER Adds a phone number to the Filter List By Phone Number Adds another phone number to the list of authorized telephone numbers Remember that only 15 numbers are allowed It works in both modes ADDSENDER Telephone number Pass Telephone Telephone number to be From 1 to 10 numeric number added to the list characters Pas Password optional Configured password Ex gt ADDSENDER 25485 pass lt Sender Added www exemys com Rev
10. inputs standard mode Six fields are shown in the table of Analog Inputs Analog Indicates the number of analog input and is not editable Name Name assigned to the corresponding input Is the name that will be visualized when a change in the input is reported Minimum Lower threshold limit for the trigger of the minimum message Maximum Upper threshold limit for the trigger of the maximum message Hysteresis Margin to avoid false triggers For more information see Appendix D Operation of Hysteresis WWW exemys com Rev 2 3 0 Dic 2011 23 GTS User s Manual Exemys Enable Allows enabling the input that we want to use to avoid false triggers 3 1 10 1 3 Digital Outputs Digital Inputs gui Analog Inputs digital Outputs Digital Outputs tpt Folow Analog Alarm Output 4 DOutputi m Output podput3 Outputs Figure 33 Configuration of the digital outputs in standard mode Three fields are shown in the table of digital outputs Outputs Indicates the number of the output and is not editable Name Name assigned to the corresponding output Is the name to which reference can be made to control the status of such output Follow analog alarm Allows activation of the output so it can follow the status of analog inputs of another GTS For more information see chapter 6 Practical Applications 3 1 10 2 Configuration of Inputs and Outputs in cus
11. the messages operate in this mode 4 1 22 Messages to or from the Serial Port To send messages to the serial port in Standard mode you use the SERIAL command in custom mode this does not work Simply the work methodology is that all messages arriving at the GTS will be sent to the serial port except those messages that are reserved or that correspond to the activation or deactivation of outputs Similarly if you send a message through the serial port it automatically becomes an SMS and is sent to the configured receipt phone list In this case SERIAL will not be the prefix of the message text therefore the message is sent as it is to its destination Remember that if characters not corresponding to the ASCII standard are received or want to be sent through the serial port these are represented by their decimal equivalent between lt gt If you are working with the serial port in By Commands mode the operation is similar except that the port has a specific format stream For more information see chapter 5 Operational modes of the serial port 4 1 23 Handling of digital outputs First the messages to activate and deactivate the outputs must be configured by the GTS Configurator For this you must access the configuration of customized outputs and place the desired message to perform the action www exemys com Rev 2 3 0 Dic 2011 32 GTS User s Manual Exemys output activatemessage D ou
12. 0 un 4 x MA lt lt cernnaangvoodgrne Ta TDA MM O lt C C C O Os St gt D DM Or D x Se eee m Do D LP www exemyscon Rev 23 0 Dic2011 41 GTS User s Manual Exemys Appendix D The hysteresis of an analog inputs defines a band in which the previous alarm status is retained before changing the current alarm status D Hysteresis operation To understand its use the following change curves of an analog input is shown gt gt Analog signal MAXIMUM ALARM V4 hax imu rm Limits HYSTERESIS hax imum Limits HYSTERESIS NORMAL STATE Figure 43 Hysteresis in the maximum limit As an example we will assume that the maximum limit is 9 0V and the hysteresis is 0 5V In the previous figure you can see the MAXIMUM ALARM message is sent when the analog signal exceeds the maximum value in this case when the input exceeds the 9 0V the NORMAL STATUS is sent when the analog signal is below the maximum limit minus the hysteresis In this case it would be when it goes below the 8 5V Having a value of hysteresis prevents from sending repeated messages every time that passes through this limit is the analog signal is varying arround of maximum limit The value of hysteresis must adapt to your needs a very small value of hysteresis can produce repeated ala
13. 1 If the GTS Configurator shows the antenna crossed out LEDs flicker slowly and in alternate manner 2 1 1 The GTS has no signal Verify 2 1 1 1 That the antenna is correctly connected 2 1 1 2 That you are within your cell phone operator coverage area 2 2 The status of the SIM card indicates fault LEDs flicker fast and in a synchronized manner 2 2 1 The GTS cannot access the SIM 2 2 1 1 If the GTS Configurator indicates SIM Inaccessible Verify that the GTS has a SIM card in place 2 2 1 2 If the GTS Configurator indicates Enter PIN the SIM card has the PIN Security code activated configure the correct PIN in the GTS See Configuring the PIN of the SIM card 2 2 1 3 If the GTS Configurator indicates SIM blocked PUK the SIM card is blocked by PUK 2 3 No evidence of error 2 3 1 Verify if the SIM card placed in the GTS has credit 2 3 2 Verify if the SIM card has a subscription or account that lets you send SMS messages 2 3 3 Corroborate that the destination telephone number coincides with the number of the SIM card of the GTS 2 3 4 Ensure that the sent message is one supported by the GTS If the message begins with a word that the GTS cannot interpret it will not respond For more information on troubleshooting please contact support exemys com WWW exemys com Rev 2 3 0 Dic 2011 39 GTS User s Manual Exemys Appendix B B Stream format in By Commands mode All characters are in ASCII format
14. 2 File GIS Communications Monitor Configuration Help Identification Operation made Parse made Pazsweord pass Standard pan Custom Recipients phone number Modify FIM Basic Configuration CONNECTED COMf Figure 26 Basic configuration screen Every time a change is made in the configuration you must press the Apply button to transfer it to the GTS The changes are permanently stored when the communication ends with the GTS Configurator If a power outage takes place before this happens the changes made will be lost WWW exemys com Rev 2 3 0 Dic 2011 19 GTS User s Manual Exemys 3 1 8 1 Identification It is possible to put a password in the SMS to increase the security level It is possible to enter text of up to eight characters If the password is left empty it is considered as disabled When the password is enabled it must be included in the SMS at the end of the message 3 1 8 2 SIM card If the SIM is protected by a PIN the same must be informed to the GTS this is done by pressing the Modify PIN button which enables entering the PIN and its confirmation Once both fields are entered you must press the Apply button so changes are applied and the SIM card is enabled Sh carg Fil Confirm Modify PIN D
15. 2 The GTS3002 has a serial communications port 16 digital inputs 6 analog inputs of 0 to 10 volts and 6 digital outputs The distribution of input and output terminals is shown below Figure 3 Terminals 1 to 18 WWW exemys com Rev 2 3 0 Dic 2011 GTS User s Manual Exemys E um AUAI If Figure 4 Terminals 19 to 36 1 1 3 GTS3003 The GTS3003 has a serial communications port 16 digital inputs 6 analog inputs of a current of 0 to 20 mA and 6 digital outputs The distribution of input and output terminals is shown below 3 5 5 5 5 5 5 5 0 5 5 5 5 5 5 5 5 u a CO Oc OO z iD a a 3 23 23 23 uo amp UJ hM C amp oh oO U e ch e C T O um AUAI If Figure 6 Terminals 19 to 36 Technical Characteristics The minimum and maximum possible values in inputs as well as current and voltage outputs and consumption of GTS are detailed below www exemys com Rev 2 3 0 Dic 2011 GTS User s Manual Exemys 1 1 4 Power Supply Input voltage Consumption idle GTS to 30 Vdc GTS to 10 Vdc Consumption in GTS to 30 Vdc transmission GTS to 10 Vdc 1 1 5 Digital inputs In order to activate digital inputs an external continuous voltage must be applied This power supply has to share the GND terminal with the GTS power supply If necessary the same power supply used to power the GTS can be used The input is of a sinking type It accepts PNP sourcing type sensors or dev
16. DEVICES OF GSM SMS REMOTE COMMUNICATION GTS Family exemys www exemys com GTS User s Manual Exemys ISO 9001 2000 Certification CLIALITY Exemys products are in permanent evolution to satisfy the needs customers needs For this reason specifications and capabilities are subject to change without notice Please find updated information at www exemys com Copyright Exemys 2009 All Rights Reserved Rev 2 3 0 Dic 2011 www exemys com Rev 2 3 0 Dic 2011 GTS User s Manual 1 Table of Contents Exemys 1 Table of Contents 3 Figures iError Marcador no definido 1 1 About this manual 5 1 1 1 Purpose of this manual 5 1 1 2 Conventions terms and abbreviations 5 General Description of the Product 5 Models 5 1 1 1 GTS2001 5 1 1 2 GTS3002 6 1 1 3 GTS3003 7 Technical Characteristics 7 1 1 4 Power Supply 8 1 1 5 Digital inputs 8 1 1 6 Digital Outputs 8 1 1 7 Analog Inputs 9 2 Installation 11 Power supply connection 11 Serial connection 11 2 1 1 RS232 Connection 11 2 1 2 5485 and RS422 Connections 12 Installation of the SIM card 12 Configuring the PIN of the SIM Card 12 LED indicators 12 3 GTS Configurator Software 14 Installation and Utilization 14 3 1 1 Installation 14 3 1 2 General Description 14 3 1 3 Configuration of the connection with the GTS 15 3 1 4 Establishing the Communication with the GTS 16 3 1 5 Organ
17. h the GTS 1 1 7 1 GTS3002 Full scale Vdc Precision Vdc Tolerance of full scale Input impedance Two examples of how to connect a voltage analog input for a single power supply and for independent power supplies are shown below Analog Input re ee Analog Input O 10 7 f eS SSeS See accum O 10 de 10 30 10 a 30 de aH TLL alim aH am Figure 11 Analog for a single power supply Figure 12 Analog for a double power supply WWW exemys com Rev 2 3 0 Dic 2011 9 GTS User s Manual Exemys 1 1 7 2 GTS3003 Full scale mA Precision mA Tolerance of full scale Shunt resistance Q Two examples where you can see the connection of a 4 20 mA sensor sharing the power supply with the GTS for passive sensors or for an active sensors with independent power supply are shown below Analog Input Analog Input mm a 2 2 T LL F n 5 o o a a T a n 1 10 a 30 Vde 7 pose a 2 S 7 5 A 3 V m j T 5 J Figure 13 Analog Input for a passive sensor Figure 14 Analog Input for an active sensor WWW exemys com Rev 2 3 0 Dic 2011 10 GTS User s Manual Exemys Chapter 2 2 Installation Power supply connection 10 30 oO V Figure 15 Power supply terminals Serial connection 2 1 1 RS232 Connection RS232 w
18. ices Input impedance 2 Two examples of how to connect directly from the same power source of the GTS as well as external power supply where it can be seen that they must share a common terminal are shown P Digital Input P Digital Input T Du a 4 Im n t L Ory Contact Aj ur 0 Lr n us a i a n T c LD n i 10 28 vdac 10 a 30 dc LU E n n SPILL alim AIA am Figure 7 Digital input with single power supply Figure 8 Digital input with double power supply 1 1 6 Digital Outputs The digital outputs are open collector type The connected load must be supplied with and external power supply and they have to share the same GND terminal with the GTS power supply Use the same power supply to power the device if necessary The output is NPN sourcing type Open Collector Maximum voltage 45 Vdc Maximun current 50 mA www exemys com Rev 2 3 0 Dic 2011 GTS User s Manual Exemys Digital Output j AN T a n Load e n a un un ay T TY 1 10 a 30 1 10 a 30 dc 2 2 ML 5 D 3 n S 3 im z1 Figure 9 Digital output with single power supply Figure 10 Digital output with double power supply 1 1 7 Analog Inputs The analog inputs referenced to the GND terminal of the GTS so the power supply to power the sensor must share the GND terminal wit
19. ied This power supply has to share the GND terminal with the GTS power supply If necessary the same power supply used to power the GTS can be used The input is sinking type It accepts PNP sourcing type sensors or devices Two examples of how to connect directly from the same power source of the GTS as well as an external power supply where it can be seen that they must share a common terminal are shown P Digital Input Digital Input 2 z m Contact 7 Lf Contact M Ax T 3 5 a 28 We a us A n 5 n om 10 28 E e 7 9 d ILL alm Figure 37 Digital input with single power supply Figure 38 Digital input with double power supply www exemys com Rev 2 3 0 Dic 2011 46 GTS User s Manual Exemys Digital Outputs The digital outputs are open collector type The load to be connected must be supplied with and external power supply and they have to share the same GND terminal with the GTS power supply If necessary the same power supply to power the equipment can be used The output is of the NPN sourcing type Supported voltage 45 Vdc Current 50 mA Digital Output 10 a 30 Yde 10 a 30 Yde Cl 7 2 n a T i LE L4 5 LI i ei A TAVANU alm lin Figure 39 Digital output with single power supply Figure 40 Digital output with double power supply Digita
20. ing screen the GTS reports all received messages and the telephone number of the sender Please take into account that if switch screens while receiving messages they will be erased 3 1 7 Monitoring Inputs and Outputs To enter the Input and Outputs monitoring screen you have to access the menu of Monitor gt Inputs Outputs or press the Monitor IO s button Q a GTS Configurator GTS3002 File GIS Communications Monitor Configuration Help Digital Inputs Digital Outputs SETE Figure 25 Inputs and Outputs monitoring screen www exemys com Rev 2 3 0 Dic 2011 18 GTS User s Manual Exemys 3 1 7 1 Digital Inputs The GTS informs in real time the value of the digital inputs Take into consideration that the number of inputs can differ according to the GTS model 3 1 7 2 Digital Outputs The GTS informs in real time the value of the digital outputs It s also possible to act on them Take into consideration that the number of outputs can vary according to the GTS model 3 1 7 3 Analog inputs The GTS continuously informs the value of analog inputs Take into consideration that some models do not have analog inputs and according to the model they can be voltage inputs or current inputs Configuration 3 1 8 Basic Configuration To enter the basic Configuration screen you must access the menu in Configuration gt Basic or by pressing the basic configuration button a GTS Configurator GTS300
21. is is a very basic configuration in which the GTS report events to a cellular phone when the digital inputs or analog alarms change or receive data from the serial port It s also possible to send orders to modify the status of the outputs or messages to the serial port from a cell phone Digital Output Activation SMS to Serial Port Input Change Report SMS trom Serial Port Outputs Figure 40 Simple home automation layout In this case the GTS can be configured in custom mode and the messages corresponding to the output activation and the input events can be defined the serial port can be configured in Transparent Centralized control This is a layout where there is a data concentrator connected to an intelligent device that receives the remote GTS messages The remote GTS report the changes to a single GTS concentrator this one must be configured in custom mode and the serial port in By Commands mode This way it is possible to send orders to any of the remote GTSs and know the GTS number sending the report The remote GTS can be configured in custom mode and the serial port in Transparent mode configuring the recipient s phone of each one with the number of the GTS concentrator WWW exemys com Rev 2 3 0 Dic 2011 37 GTS User s Manual Exemys Dig hal o prt SMS D 5 Port o SMS Tom Serial Port Digital o pat actie SMS b Serial Port hpatc karge Repo
22. ital Inputs Analog E put 4 off on edge put 5 off on edge nput 7 aff an edge nput 8 aff an edge nput 9 aff an edge Digital Inputs Input High Low Edge Enable nput 1 on off edge put 2 on off edge put 3 on off edge nput 4 on off edge put 5 on off edge A a eee 33 T c c T un n 23 5 25 5 25 T c a b T un qu put on off edge put amp on off edge aut 3 on off edge niit nn nff edge otf Eige 3 3 3 33 33 5 5 3 3 T o S Po e e Po e 5 15 15151515 51515 S S Immical 1 cm iem o 3 Figure 38 Configuration of messages of events of digital inputs EX Event Transition from 0 to 1 of input 3 lt Input 3 off on edge 4 1 25 Report of analog inputs When the analog inputs change value and status is changed according to the configured maximum and minimum a message is generated automatically reporting the change The generated message can be configured by means of the GTS Configurator in the configuration of Analog Inputs in custom mode y Digital Outputs LI a Analog Inputs Minimum Maximum Hysteresis Minimum message Normal message Maximum message 10 Bo 05 10 B0 5 5 5 5 3 5 L B olojolo Ipt4 10 ao 5 below minumun Al 4 is normalized a0 05 a
23. ith flow control PC GTS mir DB9 Female Socket DB9 Female Socket P RxD 2 TxD 3 2 RxD RTS 7 8 CTS CTS 8 e RTS 3 TxD GND 5e GND Figure 16 RS232 cable pinout www exemys com Rev 2 3 0 Dic 2011 11 GTS User s Manual Exemys 2 1 2 RS485 and RS422 Connections R5485 PIN B TR PIN 7 TR 5422 T Fin Rs R548 5 PIM R Figure 17 RS485 and RS422 pinout Installation of the SIM card For the correct operation of the device the SIM card must meet the following requirements e installed card must have a subscription or contract providing the GSM services e Verify that the telephone number assigned to the SIM card is known e If the PIN security code of the SIM card is activated you must know it and enter into the GTS when requested Configuring the PIN of the SIM Card If you place a SIM card with the PIN activated the GTS will indicate the fault by a fast flashing of the 3 LEDs in a synchronized manner In this case the PIN must be entered through the GTS Configurator Sotware For more information see SIM card If the entered PIN is not correct the device will not allow sending or receiving SMS In case the PIN is correct the GTS will store the entered code and the will continue with the normal operation Important remember that if you enter 3 times the incorrect PIN number the SIM card wil
24. ization 17 Monitoring 17 3 1 6 SMS Monitoring 17 3 1 7 Monitoring Inputs and Outputs 18 Configuration 19 3 1 8 Configuration 19 3 1 9 Serial Port Configuration 21 3 1 10 Configuration of Inputs and Outputs 22 4 Configuration Monitoring and Control by SMS 26 4 1 Configuration Messages 4 1 1 4 1 2 WWW exemys com CSERIAL Serial port configuration ADDRECIP Adds an SMS recipient Rev 2 3 0 Dic 2011 GTS User s Manual Exemys 4 1 3 Deletes an SMS recipient 27 4 1 4 CPASS Password configuration 27 4 1 5 ADDSENDER Adds a phone number to the Filter List By Phone Number 27 4 1 6 DELSENDER Deletes phone number to the Filter List By Phone Number 28 4 1 7 ENSENDER Enables Disables Filter List By Phone Number 28 Monitoring Messages 28 4 1 8 LISTALL Requests the configuration 28 4 1 9 LISTRECIP Requests the recipients list 28 4 1 10 SIGNAL Requests the value of the signal 28 4 1 11 LISTSENDER Requests the list of authorized telephones 29 4 1 12 DINPUTS Requests the value of digital inputs 29 4 1 13 DOUTPUTS Requests the value of the digital outputs 29 4 1 14 AINPUTS Requests the value of analog inputs 29 4 1 15 VERSION Requests the hardware and firmware versions of the device 29 Control Messages 29 4 1 16 SERIAL Sends messages through the serial port 29 4 1 17 DOUTPUT Modifies the status of outputs 30 4 1 18 PULSE
25. l block To unblock it you will have to enter the card s PUK For more information please contact support exemys com Once the PIN is entered you will not need to enter it again unless you change the SIM card Important When you place or remove the SIM card verify that the device is not energized otherwise the SIM card could be irreversibly damaged LED indicators The GTS has 3 LED indicators Power SMS and Configuration The Power LED indicates the device is energized WWW exemys com Rev 2 3 0 Dic 2011 12 GTS User s Manual Exemys The SMS LED indicates the device managed to access the SIM that has an acceptable signal level and that is ready to operate this LED also indicates with a single flash the reception and sending of an SMS The Configuration LED indicates when the device is being accessed through the serial port by the GTS Configurator Software for its monitoring and configuration E 2 ut ha 8 8 Figure 18 LED in the front panel Power LED SMS LED Configuration LED Fast flashing _ MEME A single flash Turns 12 second and turns off 2 second Fast flashing in a Fast flashing ina Fast flashing in a synchronized synchronized synchronized manner manner with the manner with the with the other two other two LEDs other two LEDs LEDs Alternate flashing Alternate flashing Alternate flashing with the SMS LED with the SMS LED with the Power and Configuration LEDs
26. l output to drive a Relay When used one digital output is used to a relay is necessary add in the connection a protection diode to avoid damage in the equipment The diode must be connected in reverse the anode to the output terminal of the equipment and the cathode to the positive terminal that feeds the relay The relay must be feed using a external power supply sharing the GND terminal to the power supply of the equipment or if necessary you can use the same source which feeds the GTS Digital output Digttal output 10 a 30 Yde 10 30 Wde 45 Vode Gere ee ee 2 am UY am Figure 41 Output with relay single power suply Figure 42 Output whit relay double power suplly www exemys com Rev 2 3 0 Dic 2011 47 GTS User s Manual Exemys Analog Inputs The analog inputs are referred to the GND terminal of the GTS so the power supply to feed the sensor must share the GND terminal with the GTS GTS3002 Bottom of scale Vdc Precision Vdc Tolerance full scale Input impedance KQ Two examples of how to connect an analog input of voltage for a single power supply and for independent power supplies are shown below Analog Input O 10 Analog Input zi O 10 dc 10 a 30 dc 10 30 Wde ee SiS fe ee AIA alm ea um Figure 43 Analog for a single power supply Figure 44 Analog for a double power supply www exemy
27. llowing e Time window 0 1000ms once data are received the GTS will await in silence this time before sending the SMS To disable this criterion the time window must be configured in 0 ms e End character 0 255 Indicates the last character of a serial stream before sending the SMS Important if the end character criterion is enabled and the time window is disabled the GTS will store the received data for an indefinite time until it receives the configured character or until GTS storage capacity reaches its limit If both criteria are used the first condition to be fulfilled will cause the sending of the SMS 3 1 9 3 Serial Port mode There are two modes for the Serial Port Transparent and By Commands for more information see in chapter 5 Operational modes of the Serial port You must take into account that in the By command mode the end character and the Window Time make no sense and are disabled 3 1 10 Configuration of Inputs and Outputs To enter the Configuration screen for Inputs and Outputs you can access from the menu through Configuration gt Inputs Outputs or by pressing the IOs Configuration button EA In the configuration screen of Input and Outputs you can find two or three tabs corresponding to Digital inputs Digital outputs and Analog inputs as you can see in the following figure e A Analog Inputs i D Digital Outputs Digital Inputs Ir eui rt Frakle Figure 30 Config
28. lues The following screen lets you place values that will be permanently stored by the GTS Configurator and every time the Default Values button is pressed the indicated values will be automatically inserted www exemys com Rev 2 3 0 Dic 2011 20 GTS User s Manual Exemys Edit Defaults Values Parse mode Standard 7 Enable Filter List Figure 28 Default values edit screen 3 1 9 Serial Port Configuration To enter the serial port configuration screen you must access from the menu to Configuration gt Serial Port or by pressing the Serial Port Configuration button of the GTS GTS Configurator 53002 File GIS Communications Monitor Configuration Help Serial Port Baud Rate 3600 8 Transparent By Commands DaaBis Packing party 1 Time Window 40 ms Hardware Flow Control SUE 413 serial Port Configuration CONNECTED Figure 29 Serial Port configuration screen 3 1 9 1 Serial Port The GTS has a serial communications port that has different configurations among them we find Baud Rate Data Bits Parity and flow control WWW exemys com Rev 2 3 0 Dic 2011 21 GTS User s Manual Exemys 3 1 9 2 Packing The GTS will attempt to gather several data before sending a packet through the network this way it takes maximum advantage of each message and the communication costs are reduced The criteria implemented for the end of the packet are the fo
29. mp 5 bellow minuman 1 5 iz normalized A S over maximum an los AlE bellows minuman LAIG iz normalized AAG aver maximum 3 P 4 x om on E Figure 39 Configuration of messages of analog input events If for example we have an upper limit above 9 0V and the input exceeds that threshold the corresponding message is triggered automatically and sent to the configured recipients EX Event Analog input 4 changes from 8 9V to 9 1V lt over maximum Special attention must be paid to the configured value of hysteresis to avoid the system to send SMS continuously when the input is oscillating in the change threshold For more information see Appendix D Hysteresis operation WWW exemys com Rev 2 3 0 Dic 2011 34 GTS User s Manual Exemys Chapter S 5 Operational modes GTS operational modes The GTS has two operational modes standard mode and custom mode 5 1 1 Standard mode Under this operational mode the GTS allows the reporting of changes in the inputs acting on the outputs and also receives and sends SMS to or from the serial port respectively The special feature of this mode is that the messages received or sent have a Standard format which cannot be modified and you are restricted to This has the advantage that the messages can be interpreted by other GTS The Standard messages are detailed in chapter 4 Configuration Monitoring and Contr
30. n Monitoring and Control by SMS All special messages that the GTS can receive are shown in this chapter through them it is possible to know the configuration modify it and also know the status of the inputs and outputs or act on them Take into consideration that between every parameter being sent there must be only one space The messages send a confirmation that have been received and also if an error occurred in the format Some of the messages only work in the standard operation mode and not in the custom mode this is indicated in each one 4 1 Configuration Messages BY means of SMS it is possible to configure some of the characteristics of the GTS In the current chapter the messages and the required format for each one of the configuration messages is described 4 1 1 CSERIAL Serial port configuration Configures the parameters of the serial port It works in both modes CSERIAL Baudrate Data bits Parity Flow Control Pass Baud rate Speed of serial 1200 2400 4800 9600 19200 communication 57600 115200 Pari Parity error detection E Even O Odd N No pari flow control Pass _ Password optional Configured password EX gt CSERIAL 9600 8 pass lt Port configured 4 1 2 ADDRECIP Adds an SMS recipient Adds a phone number where the SMS will be sent It works in both modes ADDRECIP phone number Pass Phone number that will be From 0 to 15 numeric characters WWW
31. nd the installation process Once installed you will be able to see in its menu Programs a folder called Exemys which contains the links to software provided by the company In this folder you will find another folder called GTS Configurator this contains the links GTS Configurator and Uninstall GTS Configurator 3 1 2 General Description The following figure shows the GTS Configurator main screen with its different sections It has a menu a tool bar which is a quick access to the menu and in the lower part a status bar presenting contextual help the connection status of the GTS configurator and the selected COM port www exemyscom Rev 23 0 Dic2011 14 GTS User s Manual Exemys E GTS Configurator Fie Communications Monitor Configuration Help Figure 19 Main screen of the GTS Configurator 3 1 3 Configuration of the connection with the GTS Before being able to establish the communication it is necessary to configure the program so it uses the correct serial port Select in the menu G7S Communications gt Serial Port s GTS Configurator File GTS Communications Monitor Contig Connect Disconnect Serial Part Figure 20 COM Configuration And then indicate the serial port where the GTS will be connected WWW exemys com Rev 2 3 0 Dic 2011 15 GTS User s Manual Exemys Serial Port Choose Serial Port Figure 21 COM selection 3 1
32. nimum Lower threshold limit for the triggering of the minimum message Maximum Upper threshold limit for the triggering of the maximum message Hysteresis margin to avoid false triggers Minimum message Message that will be sent when the analog input changes from a normal state to minimum state Normal message Message that will be sent when the analog input changes from a state of minimum or maximum to a normal state Maximum message Message that will be sent when the analog input changes from a normal state to a maximum state Enable Allows enabling the input that we want to use to avoid false triggers 3 1 10 2 3 Digital Outputs 3 Digital inputs qui Analog inputs e Digtal outputs Digital Outputs Output Activate Deactivate Activate Response Deactivate Response output 1 Turn autput 1 aff Output 1 turned on output 1 turned ott Figure 36 Configuration of digital outputs in custom mode Three fields are shown in the table of digital outputs Output Indicates the number of digital outputs and is not editable Activate Message configured to activate the corresponding output Deactivate Message configured to deactivate the corresponding output Activate Response Message returned once the activation action is executed Deactivate Response Message returned once the deactivation action is executed WWW exemys com Rev 2 3 0 Dic 2011 25 GTS User s Manual Exemys Chapter 4 4 Configuratio
33. ol by SMS where the format of each of the Standard commands is shown To better understand about this mode see chapter 6 Practical Application where useful layouts are shown where this operational mode is applied 5 1 2 Custom mode In this mode the GTS allows reporting of changes in the input acting on the outputs as well as sending and receiving messages to or from the serial port respectively The special feature of the custom mode is that the sent messages can have any format This means that for example to activate one or more outputs it is possible to define the message we want and when the message is received the outputs will be activated the same happens to turn them off In the case of digital inputs it is possible to define the message to be sent when any of the inputs goes on or off In analog inputs it is possible to configure a message being sent when the input exceeds a maximum returns to the normal status or goes bellow the configured minimum Operational modes of the Serial Port The serial communication port has two operational modes that provide different options depending on the application to be resolved Transparent mode and By Commands mode 5 1 3 Transparent mode In the Transparent mode the serial communications port behaves like a tunnel that simply receives data through the port and generates an SMS that will be sent to the only to the configured recipients list Or receives an SMS from any source n
34. ont Change Figure 27 Entering the PIN 3 1 8 3 Parse mode There are two modes of parsing the SMS received by the GTS which can be Standard or Custom For more information see chapter 5 Modes of operation of the GTS 3 1 8 4 Recipients phone number The recipients phone number are the telephone numbers that will receive all the messages sent by the GTS either messages of the serial port change events or alarm reports 3 1 8 5 Filter List by phone number The GTS will allow you to define up to 15 telephone numbers that will be accepted this means that those telephones that send messages and do not belong to this list will be ignored Only those that are in the list can act on the GTS To enable the filter you must mark the Enable Filter List check box If you do not want to enter the whole telephone number you can only enter the last digits so GTS only compares against the last digits of the telephone number for example if the number 12345 is entered in the filter list those numbers ending in 12345 will be able to access the GTS If you want to be less restrictive enter 345 and all those ending with these three numbers will be able to access 3 1 8 6 Default values The Default Values button places in the corresponding boxes the values that have been previously loaded This way we avoid having to enter these three values each time To load default values we must enter the menu File gt Edit Default Va
35. r more information see Appendix C Table of characters and the decimal equivalents EX gt SERIAL 70 5 5 test message lt 13 gt pass 4 1 17 DOUTPUT Modifies the status of outputs Changes the status of any of the outputs it is possible to turn them on or off individually It only works in Standard mode DOUTPUT Number Status Pass Name assigned in the GTS From 1 to 10 characters Configurator Output number From 1 to n Number of outputs for the model Status in which we want ON or 1 to turn on to place the output OFF or 0 to turn off Pass Password optional Configured password It is possible to act on the output by placing only the name or number if both are placed it acts by the output number For more information see in chapter 3 Standard Digital Outputs Ex1 gt DOUTPUT Motor 3 ON lt DOUTPUT 3 ON po gt DOUTPUT Motor 1 lt DOUTPUT Motor 1 EX3 DOUTPUT 3 OFF DOUTPUT 3 OFF If you give the same name to multiple outputs and you act by name all outputs will perform the action 4 1 18 PULSE Generates a pulse at the output Generates a pulse of a determined duration in the message The generated pulses are first turning on and then turning off if the output is on it will turn off once the duration of the pulse has ended It only works in Standard mode PULSE Name Number Time Pass www exemys com Rev 2 3 0 Dic 2011 30 GTS User
36. reen you must access the menu with the following path Monitor gt SMS or by pressing the SMS monitor button GTS Configurator GTS3002 Seles File GIS Communications Montor Configuration agaa SiM card Signal _ _ 3M5 Reception Level 97 ORK Sending Phone number Message 100 Monitoring incoming SMS CONNECTED COMI Figure 24 SMS monitor screen WWW exemys com Rev 2 3 0 Dic 2011 17 GTS User s Manual Exemys 3 1 6 1 SIM Card The GTS tell us the status of the SIM card it can contain four possible states e SIM Card OK The SIM works perfectly e Inaccessible SIM The SIM is not correctly placed or it is damaged e Enter PIN The SIM has a PIN number that must be entered For more information see SIM Card e Blocked SIM PUK The SIM is blocked by PUK enter the PUK number placing the SIM in the cell phone 3 1 6 2 Signal The GTS indicates the quality of the signal at this moment and it is shown in dB and the device will have to count on a minimum signal to work correctly The range of values can vary from 113dB no signal to 51dB maximum signal 3 1 6 3 Sending SMS It is possible to send messages to any destination and with a maximum length of 100 characters by means of the GTS Configurator You only have to place the telephone number the message and then press Send 3 1 6 4 SMS Reception In the SMS monitor
37. rms by maximum and normal status on the contrary a very large value can produce a loss of events of a not so significant magnitude For the lower limit case the following figure shows the behavior in which you can clearly visualize that hysteresis is applied when the analog signal goes from its lower limit to a normal value www exemys com Rev 2 3 0 Dic 2011 42 GTS User s Manual Exemys NORMAL STATE Analog signal Minimum Limits HYSTERESIS HYSTERESIS hin imum Limits MINIMUM ALARM Figure 44 Hysteresis in the lower limit You must take into account that hysteresis must be less than the maximum minus the minimum this means that the value of hysteresis should not exceed the opposing configured limits Hysteresis lt Maximum limit Minimum limit www exemys com Rev 2 3 0 Dic 2011 43 GTS User s Manual Exemys Appendix E E Factory default values Password for the reception of SMS Standard Receipt telephones Telephone to which events are reported List filter Filter list by telephone number Filter activation Activates the filter list by telephone Deactivated number Speed of communication 9600 Data bits Number of bits of each datum sent or received Flow control Control of reception buffer Activated Serial port mode Determined the behavior of the serial port Time criterion for packing End character End character criterion for packing 10 disabled Input activation Deacti
38. rt Ms Thom eral Port Dig tal Opit actio SMS D Se ral Port lipsti Report SMS tom Se Port Figure 41 Centralized control layout Inputs Outputs Serial Tunnel This configuration works as a tunnel between the GTS Serial port data entering through one end goes out on the other end and vice versa The inputs of a GTS are reflected in the other s outputs It can choose to reflect the status of the analog inputs or the status of the digital inputs The main configuration to perform a tunnel is that both devices must be configured in Standard mode and each one must have configured the other one s number Input Tunna Senal Port Tunnel ee Output Tunnel Figure 42 Tunnel layout WWW exemys com Rev 2 3 0 Dic 2011 38 GTS User s Manual Exemys Appendix A A Troubleshooting quick guide 1 1 I press the connect button and it gives me an error instantaneously 1 1 1 Verify that the selected serial port exists 1 1 2 Verify that the port is not being used by another application 1 1 3 If you use USB adapters to the serial port be sure that it is correctly connected and configured 1 2 I press the connect button and attempts to connect but it cannot do it 1 2 1 Verify that the connection cable of the serial port to the GTS is a complete cable as the one indicated in the installation section 1 2 2 idi that the selected jn is the adequate one 2
39. s Manual Exemys Name Name assigned in the GTS From 1 to 10 characters Configurator Number Output number From 1 to n Number of output for its model Time Duration of the pulse in From 1 to 60 seconds seconds Pass Password optional Configured password It is possible to act on the output placing only the name or the number if both are placed it will act by the output number For more information see chapter 3 Digital Outputs In Standard Mode Ex1 gt PULSE Reset 4 10 pass lt Pulse in output 4 of 10 seconds Ex2 gt PULSE Reset 10 pass lt Pulse in output Reset Of 10 seconds Ex3 gt PULSE 4 10 pass lt Pulse in output 4 of 10 seconds If you place the same name to multiple outputs and it acts by name all outputs will perform the action Report Messages These messages are generated asynchronically by the GTS to report certain events and will be sent to the configured receipt phone numbers 4 1 19 SERIAL Sends messages entering by the serial port When data enter through the serial port and a packet is formed according to the packing criteria it is sent to the configured receipt phone numbers This message is only sent in Standard mode SERIAL Message Ex SERIAL Test message from the serial port You should take into account that those characters entering the serial port that are not ASCII will be transformed to its equivalent representation in decimals with the format
40. s com Rev 2 3 0 Dic 2011 48 GTS User s Manual Exemys GTS3003 Bottom of scale mA Precision mA Tolerance full scale R of shunt Q Two examples where you can see the connection of a 4 20 ma sensor sharing the power supply with the GTS for passive sensors or for active sensors with independent power supply are shown below Analog Input Analog Input el aj E 2 T x 5 c o i i ay n n IE i 10 3 20 wda 1 gt 10 a 30 dc 2 a 2 LU S T 5 x 3 S 1 7 5 J Figure 45 Analog for a passive sensor Figure 46 Analog for an active sensor WWW exemys com Rev 2 3 0 Dic 2011 49
41. s in both modes Ex gt LISTRECIP lt Recipients list 112053521 15248454548 1254454542 4 1 10 SIGNAL Requests the value of the signal Requests the value of the signal in the GTS at that instant It works in both modes Ex gt SIGNAL Signal 96 dB www exemys com Rev 2 3 0 Dic 2011 28 GTS User s Manual Exemys 4 1 11 LISTSENDER Requests the list of authorized telephones Requests the list of authorized telephones that can access the GTS the character in parenthesis indicates whether it is enabled E or disabled D It works in both modes Ex gt LISTSENDER lt Senders E 54854 1548548548 1236 4 1 12 DINPUTS Requests the value of digital inputs Requests the value of digital inputs at that instant this message can originate as a response one or two messages depending on the number of inputs that the model is using It works in both modes Ex gt DINPUTS c IN1 ON IN2 ON IN3 OFF IN4 ON Continues until it sends all the inputs 4 1 13 DOUTPUTS Requests the value of the digital outputs Requests the value of the digital outputs at that instant this message can originate as a response one or two messages depending on the number of outputs the model is using It works in both modes Ex gt DOUTPUTS lt OUT1 OFF OUT2 ON OUT3 OFF OUT4 OFF Continues until it sends all the outputs 4 1 14 AINPUTS Requests the value of analog inputs Requests the value of analog inp
42. tom Mode 3 1 10 2 1 Digital Inputs 5 Digital inputs quit Analog Inputs Digital outputs Digital Inputs Low High Edge High Low Edge Enable Input 1 aff an edge Input 1 on off edge L Figure 34 Configuration of digital inputs in custom mode v Lal v v Four fields are shown in the table of digital inputs Input Indicates the number of the input and is not editable Low High Edge Text that will be sent when input is activated High Low Edge Text that will be sent when input is deactivated Enable Allows enabling the input that we want to use to avoid false triggers WWW exemys com Rev 2 3 0 Dic 2011 24 GTS User s Manual Exemys 3 1 10 2 2 Analog inputs s Digital Inputs 2 A Analog Inputs D Digital Outputs Analog Inputs Analog Minimum Mazimum JAysteresis Minimum message Normal message Maximum message Enable Input 1 1 0 9 0 0 5 Ald bella minumun amp I 1 iz normalized Ald over maximum Input 21 090 05 M2helow minumun Al2 is normalized Input 10 80 5 Al3hellow minumun 13 is normalized Input 90 05 bellow minumun Al 4 is normalized Input S 90 05 5 below minumun A 5 is normalized 10 80 05 jAlBhellow minumun Al 6 is normalized Figure 35 Configuration of analog inputs in custom mode Fight fields are shown in the table of Analog Inputs Analog Indicates the number of the analog input and is not modifiable Mi
43. umber and sends it through the serial port The main advantage of this mode is that everything arriving to the serial port becomes automatically an SMS but with the disadvantage is that the message entering through the serial port can only be sent to the phones previously configured WWW exemys com Rev 2 3 0 Dic 2011 35 GTS User s Manual Exemys Remember that if the GTS is configured en standard mode the word SERIAL will be appended to the messages received on the serial port Also remember that will have to start your SMS with the word SERIAL when you wont to send messages to the serial port In the Transparent mode of the serial port only ASCII characters are sent those characters without valid ASCII representation are sent between lt gt 5 1 4 By commands mode In this mode the serial port must receive a data stream with a defined command to send a message Among other things this mode can be used to send a message to any destination and not only to the configured recipients list When a message is received it is also possible to know the source number of the message and the time stamp when the message was sent For more details see Appendix B Format of the stream in By commands mode www exemys com Rev 2 3 0 Dic 2011 36 GTS User s Manual Exemys Chapter 6 6 Practical Applications Here we list some practical applications that can show you how and where to use the GTS Simple home automation Th
44. uration tabs of IOs ae Digital Inputs Take into consideration that not all GTS models have Analog Inputs In this case the Analog Inputs tab will not be visualized There are two different configurations for Inputs and Outputs One configuration in Standard Mode and the other one in Custom mode www exemys com Rev 2 3 0 Dic 2011 22 GTS User s Manual Exemys 3 1 10 1 Configuration of Inputs and Outputs in standard mode 3 1 10 1 1 Digital Inputs Digital Inputs qui Analog Inputs digital outputs Digital Inputs Input Hame Enable Input 1 Dinputt LJ mtz meta o oo oDe Input 4 mputS 0 Qppmus 0 0 0 0 Input 0 pur 0 Dnpull SS Dinput1 1 Figure 31 Configurations of digital inputs in standard mode In the table of digital inputs three fields are shown Input Indicates the Input number and is not editable Name Name assigned to the corresponding input Is the name that will be visualized when a change in the input is reported Enable Allows enabling the input that we want to use to avoid false triggers 3 1 10 1 2 Analog Inputs Digital Inputs Analog Inputs e GO Digital Outputs Analog Inputs Analog Minimums Histerezis Enable Input 1 A nput1 1 0 9 0 5 Ainput3 0 Input4 Inputs Input 6 Figure 32 Configuration of analog
45. uts at that instant this message can originate as a response one or two messages depending on the number of analog inputs of the model being used It works in both modes EX gt AINPUTS lt AIN1 5 90v AIN2 6 02v AIN3 0 23v Continues until is sends all the inputs 4 1 15 VERSION Requests the hardware and firmware versions of the device Through this command it is possible to know the hardware and firmware versions of your device Ex gt VERSION GTS3002 HARDWARE V3 0 FIRMWARE V1 1 0 Control Messages By means of SMS it is possible to act on the GTS 4 1 16 SERIAL Sends messages through the serial port When you want to send data through the serial port you use this command that precedes the message that we will send It only works in Standard mode SERIAL Message Pass Message Message we want to send From 1 to 120 characters through the serial port WWW exemys com Rev 2 3 0 Dic 2011 29 GTS User s Manual Exemys Pass Password optional Configured password Ex SERIAL 77 5 is a test message pass The word pass will not go out the serial port if we have the password configured with this text that is as a result we will have in the output of the serial port This is a test message If we want to send through the serial port data not having ASCII representation for example an ENTER 0 00 at the end of the message we must send the decimal code of the character between lt gt Fo
46. vated Output name DoutputN Follow analog Activation to follow the analog input Deactivated Maximum Maxmumvalefortrigger 9 0 1 10 Off on edge Text in the event of off on edge Input N off on edge On Off edge Text in the event of on off edge Input N on off edge Input enabling disabled Text to activate an output Turn on N output Text to deactivate an output Turn off N output Response to activation Response text to activation of an Output N turned on output Response to deactivation Response text to deactivation of an Output N turned off output wwwexemyscom Rev 230 Dic2001 44 GTS User s Manual Exemys Minimum value for trigger Maximum value for Maximum value for trigger __ Trigger hysteresis Minimum message Message when it enters below the E N POE RUSO minimum minimum value maximum value Input enabling Disabled Only for models GTS3002 and GTS3003 WWW exemys com Rev 2 3 0 Dic 2011 45 GTS User s Manual Exemys Appendix F F Power Supply and Inputs Outputs connections The minimum and maximum admissible values in inputs as well as current and voltage outputs and consumption of GTS are detailed below Power Supply Input voltage Consumption idle GTS at 24 Vdc GTS at 12 Vdc Consumption in GTS at 24 Vdc transmission GTS at 12 Vdc Digital inputs In order to activate digital inputs an external continuous voltage must be appl
Download Pdf Manuals
Related Search