User Manual - Better Life
Contents
1. 2 Repeat the same process to lower the other side of the basket 3 Make sure that both sides of the basket height adjustment mechanism are at the same level down or up 23 EN Adjusting the height of empty upper basket depends on the model You can adjust the height of the upper basket according to the size of the dish to be washed Use basket rollers to change the basket height 1 Turn the stoppers on the ends of the upper basket rails by turning them aside A 2 Take the basket out B 3 Change the position of the rollers place the basket into the rail and close the stoppers C 2 g JHA RR LNI Y YAW 11 WSS go SUIN NY BJA y I W B Starting Your Machine On Off Button Salt Indicator Rinse Aid Indicator Start Pause Cancel Button Display Or s Co IS 1 On Off Button It is used to power on the machine 2 Salt Indicator It is used to indicate that the salt in the salt container has depleted Refill the salt container with salt again when the indicator lights up See Adding Salt 3 Rinse Aid Indicator It is used to indicate that the rinse aid in the rinse aid container has depleted If you want to use rinse aid refill the rinse aid container with rinse aid again when the indicator lights up See Adding Rinse Aid 4 Start Pause Cancel Button It is used to startup pause or cancel the progra2. Anew machine has a peculiar odour It will fade out after a couple of washing Filters are clogged gt gt gt Check if the filter system is clean Clean the filter system regularly as illustrated in section Cleaning and Care Dirty dishes are kept in dishwasher for 2 3 days gt gt gt If you are not going to start the machine right after you have put the dishes into it remove the remnants on the dishes and run the Prewash programme without detergent every 2 days In such cases do not close the door of the machine completely in order to avoid odour build up in machine You can also use commercially available odour removers or machine cleaners 37 EN Rust discoloration or surface deterioration occurs on dishes Salt leakage exists gt gt gt Salt may cause deterioration and oxidation on metal surfaces Pay attention not to spill salt around the salt filling hole while adding salt Make sure that the salt reservoir lid is tightly closed after finishing the filling process Run the prewash programme to remove the salt that spilled inside the machine Since the salt granules that will remain under the lid will dissolve during prewash causing the lid loosen check the lid once again at the end of the programme Salty food remnants have remained on dishes for a long time gt gt gt f silverware soiled with such foods will be kept waiting in machine dirt must be removed by prewash or dishes must be washed without being
3. Pls Check the Filter Remove your filter and clean it under running water If there is remained water in the tank perform the Cancellation and have the water in the tank drained Clean any leftover deposits that have piled up in the bottom of the tank blocking the water path If the interior of your machine is dirty run it with or without detergent while it is empty Please always make sure that you scrape the large food remnants on your dishes into a dustbin using a fork paper towel or a napkin before placing them into the machine Clean your machine regularly by using machine cleaners that are specifically produced by the detergent producers 30 EN 08Z9 N3 9 Bulpoooe peinseew se pow uo 1J9 pue pow yo u UOAWNSUOD J MOd xxx p lie s sey wesbosd y 19e pasdej uun e 0 ay s eSIpui poled puodss y pue p uluu p s WesJGod ay Joye Bululewes uun 2Y Seyeoipul poled 4S1 L xx aluwesbojd s9 94 6 isn pue IOA1 S 1 ple suu IIn e pue JasUAadsip yes 1 u jos 1 JEA N e YPM JNO paleo q SNW ZpZoS NJ YM soUepsOIIe U s s ul s nii su Huss Jo 9WwwWeJHoId 990U919J9Y JOnNpoid y JO suonipuoo lueIqtue pue Besn y 0 Buipioooe Bueuo Aew s njea esey spiepue s JueA 1 BY JO siseq uo AJO eJOgGe y u p aurezqo ae onpoid y BUIUEQILI090P SIISUISOD paud y u 10 onpoid au Jo sBunueui y uo pazes sanek sinyesodw9 Ju iquue J Z pue anyesadwa EIU 1872M D G
4. 10 1 Tabletop depends on the model 2 Upper impeller 3 Lower basket 4 Lower impeller 5 Filters 6 Control panel 7 Door 8 Detergent dispenser 9 Lower impeller slot 10 Silverware basket 11 Salt reservoir lid 12 Upper basket rail 13 Upper basket with rack 14 Fan drying system depends on the model 3 EN Technical specifications Development production and sales stages of this product comply with the safety rules included in all pertaining European Community regulations 2006 95 EC 89 336 EC 93 68 EC IEC 436 DIN 44990 EN 50242 C This product complies with the following EU directives Power input 220 240 V 50 Hz Total power consumption 1900 2200 W Heater power consumption 1800 W Total current 10A Drain pump power 30 W consumption Water pressure 0 3 10 bar 3 100 N cm 0 01 1 0 Mpa GJ Technical specifications may be changed without prior notice to improve the quality of the product G Figures in this manual are schematic and may not match the product exactly G Values stated on the product labels or in the documentation accompanying it are obtained in laboratory conditions in accordance with the relevant standards Depending on operational and environmental conditions of the product these values may vary Note for test institutions Data required for performance tests shall be provided upon request Requests can be e mailed to the following addre
5. Drying hours minutes The remaining time is displayed in hours minutes For example 1 10 on the display means 1 hour and 10 minutes The time will countdown with steps of one minute allowing to follow up the time remaining to the end of the program End of program will be indicated by an audio signal and the End message Amounts of water and energy consumed are indicated in liters and kWhours respectively Note Very Lightly Soiled program structure will be activated automatically when you want to take the dust on your clean kitchenware in the chine cabinet or in the kitchen This program structure is the Fastest one of the 5 program structures on the machine defined on basis of the degree of soiling In this machine equipped with a fast program A drying level the 29 EN program time is longer then the other machines and models since they do not have drying step in fast programs Warning Messages Your machine will give you some important feedbacks while it is running You can find what to do from the following table when these informative massages are displayed Door is Open Close the door of your machine 1 Make sure that the water is not cut off 2 Make sure that the tap is open Ne Water 3 Call service if water is not cut off and the tap is open Call Service It is possible that your machine has taken in plenty of water due to various reasons Call the service
6. for 10 secs Settings will be displayed and countdown will start from 10 secs You will enter in the Settings menu at the end of the countdown and the language selection menu Language will be displayed Ref Program will be displayed when you press the Start Stop button once Press and hold the Start Stop button for 5 secs to enter the reference program menu Press the Start Stop button to display ON or OFF options Press and hold the Start Stop button for 5 secs to save your selection Saved will be displayed Turn off the machine by pressing the On Off button to exit the menu Turn on your machine by pressing the On Off button to return to the washing display e When you press Start Stop button reference program will start e After wash cycle ends if you want to run the reference program again apply the same procedure Key Lock Your machine is equipped with a key lock function in order to avoid anyone else but you particularly the children to interfere with and change the program flow while the machine is operating Key lock also functions as a safety system that prevents you from performing accidental operations by pressing a button unintentionally when you want to add or take out dishes from the machine Key lock is activated automatically in the following conditions e 30 seconds after the machine is turned on by pressing the On Off button and the program is started e If
7. want to add take out dishes to from the machine before determining the level of washing Then you can stop the washing by pressing the Start Pause Cancel key again In this case following messages will displayed consecutively Paused Press to continue Press the Start Pause Cancel button again to deactivate the key lock and resume the program if the key lock is EN activated after you have completed your operation Canceling a program You need to perform a canceling operation if you want to end a program before it is over To cancel a program Deactivate the key lock if it is active Paused is displayed if you press the Start Pause Cancel key when the key lock is deactivated If you continue to keeping the Start Pause Cancel key pressed the countdown of 5 seconds starts and the following messages are displayed consecutively Cancel 5 Cancel 4 Cancel 3 Cancel 2 Cancel 1 Cancel Release the key at the end of the countdown The message Cancelling is displayed for 45 seconds during the discharge operation Cancelled will be displayed when the operation is completed In this case you can turn off your machine with the On Off key or make it ready for the next cycle by pressing the Start Pause Cancel button WARNING There might be residues of detergent or rinse aid in the machine and or on the pieces already washed dependi
8. JO DIIBA ase s njea uonduinsuo5 sheleny i o xxx M pouu JHO poui uo 1J91 p Aouu li ae sjueuw POO uo s snp abie y saye y SAOWAL O yll Bunrem dey aie pinom noA yeu seysip uun JEU s usip JO JO 10 Al eIp uuuul Buoy e 104 Buem Al 1eIp uuuu Jo Ajayelpawiw paysem aq o ulydeu e s usiq jo d sued jdoy pue p ue j p ysem jou pue peysem jnq UNA pedesos 10 1 JEA Bunrem d y BulAy pue suedsones asd jou ae yey p ue jv d jou p ue lo id jou Butuuni sapun pauesjo ase yeu s usip Ajlep Ajlo saysip Ajlo pue saysip p lios AjlAeay ase yey Seysip udejgeu s usip Jose zey s ueuuu ipoo pajos uinip uu y pajios JIAB U J 10 Ayjeoyeuoyne io Ajpeonewoyne so Ajjeonewone abe ym seysip Jo 10 wesBoud Bulysem Ayjeonyewojne pal paddy paddy paddy Ayjeonewojne paddy jeolwouose soy nzes dw Hulyse uomeoipul Builios Jo 15 q p lioS llAB H p lioS A PS p lios Anu6i1 p lios nu6r1 SA Butllos Jo aeibaq 3o 02 3 OV OLNV s uslp ay Jo ulos Jo 16 p y uo peseq seinjonsjs WesGod 1lu l jiip u JO uo uni UBD BUIYOeW Inoy AyQUeNb szem pue uun inie1 duu ajeldosdde y uluuj p lleoneuuo ne pue Bulysem Buunp Jayem y JO Bullios Jo sasHap ayy 153 p IIIA JOSUaS ss ullue O O 02 9 OF OLNV jqeL s n eA uonduinsuooS BeJ AV pue eyeg weibolg 31 EN 6 Maintenance and cleani
9. functional before disposing of the product 10 EN EJ Prewashing Tips for energy saving Following information will help you use the product in an ecological and energy efficient manner e Wipe away any coarse food remnants on the dishes before putting them in the product e Operate the product after filling it completely e When selecting a programme refer to the Programme Table e Do not put more detergent than suggested on the detergent package Water softening system G The dishwasher requires soft water If the hardness of the water is above 6 dH the water must be softened and descaled Otherwise ions that create the hardness will accumulate on the surfaces of the dishes and may adversely affect the washing shining and drying performances of the product The product is equipped with a water softening system which reduces the hardness of incoming water This system softens the supply water that enters into the product to a level that will allow washing the dishes with the required quality Adjusting the water softening system Washing performance will increase when water softening system is adjusted properly Use the test stripe supplied with the product to determine the supply water hardness in order to adjust the system 11 EN Adding salt Water softening system needs to be regenerated in order for the product operates with the same performance continuously Dishwasher salt is used
10. to remove the salt that spilled inside the machine Since the salt granules that will remain under the lid will dissolve during prewash causing the lid loosen check the lid once again at the end of the programme Water hardness setting is low or salt level is insufficient gt gt gt Measure the hardness of the supply water appropriately and check the water hardness setting Dishes are not placed orderly in the machine gt gt gt When placing the glasses and other glassware into the basket lean them not against other dishes but the edges or racks of the basket or the glass support wire Striking of the glasses to each other or to other dishes due to the impact of water during washing can cause breaks or scratches on their surfaces 39 EN A smear remains on glasses that resembles milk stain which can not be removed when wiped by hand A bluish rainbow appearance occurs when the glass is pointed to light Excessive rinse aid is used gt gt gt Lower rinse aid setting Clean the spilled rinse aid when adding rinse aid Corrosion has occurred on glass due to soft water gt gt gt Measure the hardness of the supply water appropriately and check the water hardness setting If your supply water is soft lt 5 dH do not use salt Choose programmes that wash in higher temperatures e g 60 65 C You can also use glass protective detergents that are commercially available Foam forms in the machine Dishes are washed with h
11. DISHWASHER Please read this user manual first Dear Customer We hope that you get the best results from the product which has been manufactured in state of the art plants and passed through a strict quality control procedure Therefore please read the entire user manual carefully before using the product and keep it as a reference for future use In case of transferring the product to someone else give the manual as well The user manual will help you use your product in a fast and safe way e Read the user manual before installing and starting your product e Always follow the safety instructions e Keep this user manual within easy reach for future reference e Read also the other documents supplied with the product Remember that this user manual is also applicable for several other models Differences between models will be identified in the manual Explanation of symbols Throughout this User Manual the following symbols are used Important information or useful hints about usage Warning for hazardous situations with regard to life and property A Warning for electric shock CONTENTS 1 Dishwasher 3 2 Important safety instructions 5 General safety 5 Intended use 5 Children s safety 6 3 Installation 7 Appropriate installation location 7 Connecting water supply 7 Connection to the drain 8 Adjusting the feet 9 Aquasafe 9 Electrical connection 9 Initial use 9 Disposing of packaging material 10 Tr
12. an any spilled rinse aid outside the reservoir Rinse aid that spilled accidentally will cause foaming and it will eventually decrease washing performance 15 EN 4 Turn the rinse aid amount adjuster manually to a position between 1 and 6 4 If there are stains on tableware items after washing level must be increased and if there is a blue trace after wiping them by hand it must be decreased This is set to position 4 as factory default Items not suitable for washing in the dishwasher Never wash dishes soiled by cigarette ash candle remnants polish dyestuff chemicals etc in your dishwasher Do not wash iron alloy items in the dishwasher It can get corroded or leave stains on other items Do not wash silverware and cutlery with wooden or bone stems glued pieces or pieces that are not resistant to heat as well as copper and tin plated containers in the dishwasher Decorative prints of chinaware as well as aluminum and silver items may get discoloured or tarnished after washing in the dishwasher just as it happens in handwashing as well Some delicate glass types and crystals may become dull in time We strongly recommend you to check if the tableware you are going to purchase is suitable for washing especially in the dishwasher Placing the dishes into the dishwasher You can use your dishwasher in the optimum way with respect to energy consumption and washing and drying performanc
13. and wash detergent by hand but not rinsed before placing them into the machine gt gt gt Hand wash detergents do not contain antifoam There is no need to hand wash the dishes before placing them into the machine Removing the coarse soil on the dishes under tap water with a tissue paper or fork will be sufficient Rinse aid has spilled into the machine when adding rinse aid gt gt gt Take care that rinse aid is not spilled in the machine when you are filling it Clean any spilled rinse ait with the help of a tissue paper towel Lid of the rinse aid reservoir is left open gt gt gt Make sure that the lid of the rinse aid reservoir is closed after adding rinse aid Kitchen utensils are broken Dishes are not placed orderly in the machine gt gt gt Load the dishes as described in the user manual Baskets are overloaded gt gt gt Do not overload the baskets in excess of their capacity Water remains in the dishwasher at the end of the programme Filters are clogged gt gt gt Check if the filter system is clean Clean the filter system regularly as illustrated in section Cleaning and Care Discharge hose is clogged blocked gt gt gt Check the discharge hose If necessary remove the discharge hose clear the blockage and insert is as illustrated in the user manual G If you cannot eliminate the problem although you follow the instructions in this section consult your dealer or the Authorised Ser
14. ansportation of the product 10 Disposing of the old product 10 4 Prewashing 11 Tips for energy saving 11 Water softening system 11 Adjusting the water softening system 11 Adding salt 12 Detergent 13 Adding detergent 13 Tablet detergents 14 Rinse aid 15 Silverware basket 18 Silverware basket piece 18 Movable silverware basket 18 Collapsable lower basket wires 2 pieces 19 Collapsable lower basket wires 4 pieces 19 Lower basket bottle wire 19 Lower basket multipurpose height adjustable service rack 20 Upper basket height adjustable rack 20 Upper basket drawer 21 Upper basket glass support piece 21 Collapsable upper basket wires 21 Collapsable upper basket wires 22 Adjusting the height of loaded upper basket 22 Adjusting the height of loaded upper basket 23 Adjusting the height of empty upper basket 24 5 Operating the product 25 Keys 26 Preparing the machine 26 Programme selection 27 Adding an auxiliary function to the programme 27 Setting Time Delay function 27 Starting the programme 28 Child Lock 28 Programme follow up 28 Canceling a programme 28 Changing a programme 29 Salt indicator 29 Rinse Aid indicator 29 End of programme 30 6 Maintenance and cleaning 32 Cleaning the outer surface of the product 32 Cleaning the interior of the machine 32 Cleaning the filters 32 Cleaning the hose filter 33 Cleaning the impellers 33 7 Troubleshooting 35 El Dishwasher Overview 13 12 11
15. be heard when the lid is closed GJ In programmes with prewash and at high temperature in which you use tablet detergents make sure that the detergent dispenser lid is closed firmly G Use powder detergent in short programmes without prewash since the solubility of the tablet detergent changes depending on the temperature and time Excessive usage of powder detergents will cause the detergent not dissolve completely and will also cause scratches on the glassware Tablet detergents Table detergents exhibit water softening and or rinse aid effect in addition to detergent effect Some types of these detergents also contain special purpose washing chemicals such as glass and stainless steel protectors G Tablet detergents give satisfying results only under certain usage conditions The best washing performance in dishwashers is obtained by using detergent 14 rinse aid and water softening salt individually GJ Information about suitable places detergent dispenser basket etc in the dishwasher to place the tablet can be found amongst the usage instructions on the packages of the tablet detergents Tablet detergent types commonly found in the market 2in1 Contains detergent rinse aid or water softening salt 3in1 Contains detergent rinse aid and water softening salt 4in1 Contains glass protectors in addition to detergent rinse aid and water softening salt 5in1 Contains glass and stainless steel prote
16. can directly be connected to the drain hole or sink s drainage The length of this connection must be min 50 cm and max 100 cm from the floor 10 20 3 40 50 6 70 8 9 10 110 0 A discharge hose longer than 4 meters causes dirty washing Attach the water discharge hose to the drainpipe without bending it Tightly fix the water discharge hose to the drainpipe in order to prevent any dislocation of the water discharge hose during operation of the product EN Drainpipe must be connected to the sewage system and it should not be connected to any surface water Adjusting the feet If the door of the product cannot be closed properly or if the product swings when you push it slightly then you need to adjust the feet of the product Adjust the feet of the product as illustrated in the installation manual supplied with the product Aquasafe depends on the model Protect the Aquasafe system against water leaks that may occur at hose inlet Water contact with the valve box of the system must be prevented Otherwise electrical assembly will get damaged If the Aquasafe system is damaged unplug the product and call the Authorised Service Agent N As the hose set contains electrical connections and assemblies never shorten or lengthen the hose with extension hoses 3 4 9 Electrical connection Connect the product to a grounded outlet protected by a fuse complying w
17. ctors in addition to detergent rinse aid and water softening salt G Observe the instructions of the detergent manufacturer on the package when using tablet detergents When you switch to powder detergent from tablet detergent 1 Make sure that salt and rinse aid reservoirs are full 2 Set the water hardness to the highest level and perform an empty run 3 After the empty washing cycle review the user manual and readjust the water hardness level so as to suit the water supply 4 Make the appropriate rinse aid settings GJ Depending on the model salt indicator and or rinse aid indicator must be enabled again if they were disabled before EN Rinse aid g The rinse aid used in dishwashers is a special combination used to increase drying efficiency and prevent water or limescale stains on the washed items For this reason care must be paid to have rinse aid in the rinse aid reservoir and to use rinse aids produced specially for dishwashers only Check Rinse Aid Indicator to determine whether it is necessary to add rinse aid or not 3 Having a dark light on the indicator shows that there is sufficient amount of rinse aid in the dispenser If the colour of the indicator is light add rinse aid 1 Open the lid of the rinse aid reservoir by pressing its latch B 2 3 g Fill the reservoir until MAX level Close the lid of the reservoir by pressing on it lightly Wipe cle
18. d make sure that it is installed correctly Baskets are overloaded gt gt gt Do not overload the baskets in excess of their capacity Detergent is stored under unsuitable conditions gt gt gt If you are using powder detergent do not store the detergent package in humid places Keep it ina closed container if possible For ease of storing we recommend you to use tablet detergents Detergent is not sufficient gt gt gt f you are using powder detergent adjust the amount of detergent according to the soiling degree of your dishes and or programme definitions We recommend you to use tablet detergents for optimum results Rinse aid is not sufficient gt gt gt Check the rinse aid indicator and add rinse aid if necessary Increase the rinse aid setting if there is enough amount of rinse aid in the machine Detergent dispenser lid is left open gt gt gt Make sure that the detergent dispenser lid is closed tightly after adding detergent 35 EN Dishes are not dry at the end of cycle Dishes are not placed orderly in the machine gt gt gt Place your dishes in a way that no water will accumulate in them e Rinse aid is not sufficient gt gt gt Check the rinse aid indicator and add rinse aid if necessary Increase the rinse aid setting if there is enough amount of rinse aid in the machine e Machine is unloaded right after the programme is over gt gt gt Do not unload your machine right after washing process i
19. detergent dispenser and close its lid e Start the program by pressing Start Pause Cancel button WARNING Pay attention not to open the door of the machine when it is running Stop the machine by pressing Start Pause Cancel button if you have to open the door Then open the door There may be arush of vapor when you open the door of your machine Be careful Close the door and press Start Pause Cancel button again Program will resume running e Key lock will be activated 30 seconds after the program starts and Key Lock Activated will be displayed e Energy saving system will be activated 90 seconds after the program starts and the display is dimmed If you touch the button again display brightness returns to its original status e End will be displayed when the program is over The amount of 26 EN water and energy consumed will be displayed consecutively Press the On Off button to turn off your machine when the program is over Close the tap Unplug the mains plug from the wall socket Leave your dishes in the machine for about 15 minutes after they are washed in order to have them cooled down Your dishes will dry in a shorter time if you leave the door of your machine ajar during this period This will increase the drying effectiveness of your machine Selecting the Reference Program Press the On Off button to turn on your machine when its door is open Then press the Start Stop button
20. e Detergent You can use powder or tablet detergent in the machine G Only use in the machine the detergents produced particularly for use with dishwashers We recommend you not to use detergents that contain chlorine and phosphate as they are harmful for the environment G Contact the detergent producer if the dishes are wet and or if you notice limescale spots particularly on glasses after the washing programme is over Adding detergent G Refer to the Programme Table to determine the correct amount of detergent for the selected programme A Do not put solvents into the detergent dispenser There is the risk of explosion Put the detergent into the detergent dispenser just before operating the machine as illustrated below 1 Push the latch to right to open the detergent dispenser lid A 2 Put suggested amount of powder or tablet detergent in the dispenser GJ Inside the detergent dispenser there are level markings that help you use appropriate amount of detergent When brimful detergent dispenser will contain 40 cm of detergent Fill detergent up to 15 cm or 25 cm level marks in the detergent dispenser according to fullness of the machine and or soiling degree of the dishes 1 GJ If dishes have been waiting for a long time and have dried residues fill the 5 cm compartment too 5 13 EN 3 Close the detergent dispenser lid by pressing on it lightly A click will
21. e assembly C 4 Clean all three filters under tap water by means of a brush 5 Replace the metal plastic filter 6 Place the coarse filter into the microfilter Make sure that it is properly seated Turn the coarse filter clockwise until a click sound is heard Do not use the dishwasher without filter GJ Incorrect placement of the filters will reduce washing efficiency Cleaning the hose filter Damages on the machine that may be caused by impurities coming from the urban supply water or your own water installation such as sand dirt rust etc can be prevented by means of the filter attached to the water inlet hose Check the filter and the hose regularly and clean them if necessary 1 Turn off the tap and remove the hose 2 After taking out the filter clean it under running tap water 3 Place the cleaned filter back to its seat in the hose 4 Install the hose to tap Cleaning the impellers Clean the impellers at least once a week in order for the machine operates efficiently Lower impeller Check if the holes on the lower impeller 1 are clogged If they are clogged remove and clean the impeller Pull the lower impeller up to remove it A B 33 EN Upper impeller Check if the holes on the upper impeller 2 are clogged If they are clogged remove and clean the impeller Turn its nut to left to remove the upper impeller C D Make sure that the nut is ti
22. e only if you place the dishes in an orderly way e Wipe away any coarse food remnants bones seeds etc on the dishes before placing them in the dishwasher e Place thin narrow pieces in the middle sections of baskets if possible e There are two separate baskets in which you can place your dishes in the dishwasher Place the heavily soiled and bigger items in the lower basket and smaller delicate and light items in the upper basket e Place the hollowed dishes such as bowls glasses and pans upside down in the dishwasher Thus accumulation of water in deep hollows is prevented A To prevent possible injuries always place the sharp and pointed dishes such as service fork bread knife etc upside down so as their pointed ends will face down or they will lie horizontally on the dish baskets e Unload dishes in the lower basket first and then the dishes in the upper basket 16 EN Suggestions for loading the dishwasher Improper Loading Of Dishware fay ve i Ol HX JIN Z N WN Silverware basket Movable silverware basket depends on the model depends on the model Silverware basket is designed to wash Since the cutlery basket can be moved your dishes such as fork spoon and A B you can create a wide
23. e that the water inlet and discharge hoses are not folded pinched or crushed while pushing the product into its place after installation or cleaning procedures When placing the product pay attention not to damage the floor walls piping etc Do not hold the product from its door or panel to move it Appropriate installation location e Place the product on a solid and 7 flat floor that has sufficient load carrying capacity The product must be installed on a flat surface in order for the door to be closed comfortably and securely e Do not install the product at places where temperature may fall below 0 C e Place the product at least 1 cm away from the edges of other furniture e Place the product on a rigid floor Do not place it on a long pile rug or similar surfaces Do not place the product on the power cable e Make sure that you select a location that will allow you to load and unload the dishes in a fast and comfortable manner e Install the product in a place close to the tap and the drain hole Select the installation location by considering that it will not be changed after the connections are made Connecting water supply We recommend attaching a filter on the house apartment supply water inlet to protect the machine from damages that may arise from impurities sand dirt rust etc coming from the urban water supply system or from your own water system as well as to prevent complai
24. emained in the product due to the quality control processes in the production It is not harmful for the product Disposing of packaging material Packaging materials are dangerous to children Keep packaging materials in a safe place away from reach of the children Packaging materials of the product are manufactured from recyclable materials Dispose of them properly and sort in accordance with recycled waste instructions Do not dispose of them with normal domestic waste Transportation of the product A If you need to move the product do it in upright position and hold from the rear side Slanting the product onto its front side may cause the electronic parts in it get wet and damaged 1 Unplug the product before transporting it 2 Remove water drainage and water supply connections 3 Drain the remaining water in the product completely Disposing of the old product Dispose of the old product in Ke an environmentally friendly manner Some parts of the m product are manufactured from recyclable materials Along with a recycling symbol information about its nature PE PS POM etc is also provided on the material These materials should not be disposed as normal domestic wastes Refer to your local dealer or solid waste collection centre in your area to learn how to dispose of your product A For children s safety cut the power cable and break the locking mechanism of the door so that it will be non
25. et height adjustment mechanism are at the same level down or up To lower the basket 1 Press the latch on the basket adjustment mechanism right or left to lower the basket B Adjusting the height of loaded upper basket depends on the model Basket adjustment mechanism on the upper basket of the machine is designed to allow you create wider areas in the upper or lover section of the machine based on your requirements by adjusting the height 22 EN 2 Repeat the same process to lower the other side of the basket 3 Make sure that both sides of the basket height adjustment mechanism are at the same level down or up Adjusting the height of loaded upper basket depends on the model Basket adjustment mechanism on the upper basket of the machine is designed to allow you create wider areas in the upper or lover section of the machine based on your requirements by adjusting the height of the loaded basket in up or down directions without removing it from the machine To raise the basket 1 Grab one of the upper basket wires right or left and lift it up A 2 Repeat the same process to raise the other side of the basket 3 Make sure that both sides of the basket height adjustment mechanism are at the same level down or up To lower the basket 1 Press the latch on the basket adjustment mechanism right or left to lower the basket B
26. ever unplug by pulling on the cable always pull out by grabbing the plug The product must be unplugged during installation maintenance 5 cleaning and repairing procedures Always have the installation and repairing procedures carried out by the Authorised Service Agent Manufacturer shall not be held liable for damages that may arise from procedures carried out by unauthorised persons Never use chemical solvents in the product They bring forth risk of explosion When you pull the upper and lower baskets out completely the door of the product will bear all the weight of the baskets Do not put other loads on the door otherwise the product may tilt Never leave the door of the product open apart from loading and unloading procedures Do not to open the door of the product when it is running unless necessary Be careful for the rush of hot vapour when you need to open the door Intended use EN This product has been designed for domestic use It must be used to do the domestic type dishes only Only dishwasher safe detergents rinse aids and additives must be used The manufacturer waives any responsibility arisen from incorrect usage or transportation The service life of your product is 10 years During this period original spare parts will be available to operate the appliance properly This product should not be used by persons with physical sensory or mental disorders or unlearned or inexpe
27. for this purpose g g Use in your product only the special softening salts produced particularly for use in dishwashers We recommend using granular or powder softening salts Do not use salts containing insoluble substances such as table salt or common salt in the machine Performance of water softening system may deteriorate in time Salt reservoir will fill with water when you start the product Therefore add the softening salt before starting the machine First take the lower basket out to add softening salt Turn the salt reservoir lid in counter clockwise to open it A B Before initial use fill the water softening system with 1 litre of water C Fill the salt reservoir with salt by using salt funnel D To speed up dissolution rate of salt in water stir it with a spoon You can put about 2 kg of softening salt into the salt reservoir Replace the lid and tighten it securely when the reservoir is full 12 EN 5 If you will not start a washing programme immediately after adding the salt run the machine empty in the shortest programme to dissolve and wash away the scattered salt in the machine GJ Since different salt brands in the market have different particle sizes and since the water hardness may vary dissolution of the salt in water may take a couple of hours Therefore Salt Indicator remains on for a while after adding salt into the machin
28. ged during washing If you wish to place large volume pieces on the upper basket release the tab of the glass support piece from the upper basket wire it is hooked to Thus you can obtain a wider space III NCC ee pall eee PT L e STII Wow Collapsable upper basket wires depends on the model There are foldable wires on the upper basket of the machine that you can lay down when you need larger space for big dishes To bring the collapsable wires into horizontal position grab the first collapsable wire and push it in direction A or B Place your larger dishes into the area created To bring the wires back to vertical position just lift them up Collapsable wires will click into the latch again HI 21 EN Collapsable upper basket of the loaded basket in up or down wires directions without removing it from the depends on the model machine To bring the collapsable wires on the f upper basket of the machine into To raise the basket horizontal position press on the latch 1 Grab one of the upper basket wires right or left and lift it up A 1 Place your larger dishes into the area created 2 To bring the wires 2 Repeat the same process to raise back to vertical position just lift them the other side of the basket up 3 Make sure that both sides of the bask
29. ghtened well when installing the upper impeller BAN OS 4 gt q Do by ie 34 EN Troubleshooting Machine does not start Power cable is unplugged gt gt gt Check if the power cable is plugged in Fuse is blown gt gt gt Check the fuses in your house Water is cut gt gt gt Make sure that the water inlet tap is open Door of the machine is open gt gt gt Make sure that you have closed the door of the machine On Off button is not pressed gt gt gt Make sure that you have turned on the machine by pressing the On Off button Dishes are not washed clean Dishes are not placed orderly in the machine gt gt gt Load the dishes as described in the user manual Selected programme is unsuitable gt gt gt Select a programme with a higher temperature and cycle time Impellers are stuck gt gt gt Prior to starting the programme turn the lower and upper impellers by hand to make sure that they rotate freely Impeller holes are clogged gt gt gt Lower and upper impeller holes might be clogged with food remnants such as lemon pips Clean the impellers regularly as illustrated in section Cleaning and Care Filters are clogged gt gt gt Check if the filter system is clean Clean the filter system regularly as illustrated in section Cleaning and Care Filters are installed incorrectly gt gt gt Check the filter system an
30. hey have penetrated in deteriorated surfaces Desired washing performance can not be obtained at kitchen utensils with deteriorated surfaces and it is not suitable to use such utensils in terms of hygiene as well It is not recommended to wash such kitchen utensils in dishwasher Detergent is stored under unsuitable conditions gt gt gt If you are using powder detergent do not store the detergent package in humid places Keep it ina closed container if possible For ease of storing we recommend you to use tablet detergents 36 EN Lime traces remain on dishes and glassware gains a misty appearance Rinse aid is not sufficient gt gt gt Check the rinse aid indicator and add rinse aid if necessary Increase the rinse aid setting if there is enough amount of rinse aid in the machine Water hardness setting is low or salt level is insufficient gt gt gt Measure the hardness of the supply water appropriately and check the water hardness setting Salt leakage exists gt gt gt Pay attention not to spill salt around the salt filling hole while adding salt Make sure that the salt reservoir lid is tightly closed after finishing the filling process Run the prewash programme to remove the Salt that spilled inside the machine Since the salt granules that will remain under the lid will dissolve during prewash causing the lid loosen check the lid once again at the end of the programme There is a different odour in the machine
31. iod and analysing the correct program structure Filled boxes on the display indicate the degree of soiling One filled box indicates that the dishes are very lightly soiled while five filled boxes indicate that the dishes are heavily soiled You can find information about the program flows that can be followed depending on the degrees of soiling in Program Data and Average Consumption Values Table The amount of dishes that you load into your machine is determined with the load sensor and this helps to determine the amount of water to add The amount of dishes do not affect analysis It only affects the time that takes to analyse the degree of soiling of the dishes and the program flow that will be followed according to the analysis result Programme determined is displayed upon completion of the analysis and the program selected on basis of the degree of soiling is displayed WARNING You must not add dishes into the machine after the program is determined Washing program is determined on basis of the degree of soiling of the dishes in the machine Adding dishes into the machine after the washing program is determined can prevent to make an effective washing Following messages are displayed consecutively to indicate the program steps that are followed and the time remaining to the end of the program after the program structure is determined Washing hours minutes Rinsing hours minutes
32. ith the values in the Technical specifications table Manufacturer shall not be liable for any damages that will arise when the product is used without grounding in accordance with the local regulations e Connection must comply with national regulations e Power cable plug must be within easy reach after installation Unplug the product after the washing programme is over e The voltage and allowed fuse or breaker protection are specified in the Technical specifications section If the current value of the fuse or breaker in the house is less than 16 Amps have a qualified electrician install a 16 Amp fuse e The specified voltage must be equal to your mains voltage e Do not make connections via extension cables or multi plugs Damaged power cables must be replaced by the Authorised Service Agent If the product has a failure it should not be operated unless it is repaired by the Authorised Service Agent There is the risk of electric shock Initial use Before starting to use the product make sure that all preparations are made in accordance with the instructions in sections Important safety instructions and Installation e To prepare the product to do the dishes perform first operation in the shortest programme with EN detergent while the machine is empty During the initial use fill the salt reservoir with 1 litre of water prior to filling it with salt G Some water might have r
33. kept waiting Electric installation is not grounded gt gt gt Check if your machine is connected to the actual grounding line Otherwise the static electric created in the product causes arcs on the surfaces of metal items creating pores removing the protective cover on the surface and causing discoloration Intensive cleansers such as bleaches are used gt gt gt Protective cover on metal surfaces gets damaged and looses its efficiency in time when it gets in contact with cleansers such as bleach Do not wash your dishes with bleach Metal items particularly such as knives are used for purposes other then their intended uses gt gt gt Protective cover on the edges of knives may get damaged when they are used for purposes such as opening cans Do not use metal kitchen utensils out of their intended uses Silverware are made of low quality stainless steel gt gt gt Corrosion on such items is inevitable they should not be washed in dishwashers Kitchen utensils that are already corroded are washed in dishwasher gt gt gt Rust on a corroded item can migrate to other stainless steel surfaces and cause corrosion on those surfaces as well Such items should not be washed in dishwashers 38 EN Detergent remains in detergent dispenser Detergent dispenser was damp when adding detergent gt gt gt Make sure that the detergent dispenser is dried well prior to filling it with detergent Detergent is added long before the wa
34. m 5 Display It shows the program steps time remaining to the end of the program and warning messages ranguage Selection Press the On Off button to turn on your machine when its door is open Then press the Start Stop button for 10 secs e Settings will be displayed and countdown will start from 10 secs e You will enter in the Settings menu at the end of the countdown and the language selection menu Language will be displayed e The default language will be shown on the machine after you have pressed and held the Start Stop button for 5 secs e Proceed by pressing the Start Stop button to see the other languages e Press and hold the Start Stop button for 5 secs when the language you would like to select appears on the screen Saved will be displayed e Turn off the machine by pressing the On Off button to exit the language selection menu e Turn on your machine by pressing the On Off button to return to the washing display NOTE The key lock will not be activated when the door is open 25 EN and program cancellation will not be possible Starting Your Machine e Open the tap e Plug the mains plug into the wall socket e Open the door e Press On Off button e Check if the salt and rinse aid indicators light and add salt and or rinse aid if needed e Place the dishes e Check if the upper and lower impellers rotate freely e Put sufficient amount of detergent in the
35. ng Service life of the product extends and 1 Turn the micro filter 3 and frequently faced problems decrease if it coarse filter 2 assembly counter is cleaned at regular intervals clockwise and pull it out from its A Unplug the product and turn off the seating A tap before attempting any cleaning procedures GJ Do not use abrasive substances for cleaning GJ Clean the filters and impellers at least once a week Cleaning the outer surface of the product Clean the outer surface and door gaskets of the product gently with a mild cleaning material and damp cloth Wipe the control panel only with a damp cloth Cleaning the interior of the machine e Clean the interior of the machine and the tank by running a prewash programme without detergent or a long washing programme with detergent based on the degree of soiling e If water has remained in the machine drain the water by performing the procedures under the topic Canceling a programme If the water cannot be discharged clean any leftover deposits that have piled up in the bottom of the machine blocking the water path Cleaning the filters Clean the filters at least once a week in order for the machine operates efficiently Check if food residues are left on the filters If there are food residues on filters take them out and clean well under running water 3 Press the two pawls on the coarse filter inwards and separate the coarse filter from th
36. ng on the step the cancelled program was in at the end of such cancellation Program Step Follow up You can follow up the washing step of the current program by means of the warning notes on the display Washing is displayed for the steps at which the food remnants are removed or a washing with detergent is made The degree of soiling of the dishes is determined by measuring the degree of soiling in the washing water by means of the cleanliness sensor The cleanliness sensor determines what to do in the following steps by measuring the degree of soiling of the water regularly Washing temperature washing time washing pressures and water amount in adjusted on basis of the information received from the cleanliness sensor This program is developed to avoid unnecessary water and energy consumption by washing the dishes in the most appropriate conditions for the degree of soiling of the dishes Analysing is displayed during the decision steps The analyse is made during the first 10 30 minutes at the beginning of the washing depending on the temperature 28 EN of the mains water dissolution rate of the dirt and level of soiling of the dishes Analysis takes less time for lightly soiled dishes but more time for heavily soiled dishes Cleaning operation continues during the analysis steps In this stage the animation on the screen consisting of boxes indicates that the machine is in the decision per
37. nts such as yellowing or sludge accumulation at the end of washing EN There are two different types of water inlet hoses e Cold water inlet hose up to 25 C e Hot water inlet hose up to 60 C A Please check which one is applicable to your model A If you plan to connect your machine to natural energy resources or to the central hot water supply first check out the temperature values written on your water inlet hose to make sure that it is suitable for such usage If your hose is not suitable apply to your Authorised Service Agent to have it changed e Do not use old or used water inlet hose on the new product Use the new water inlet hose supplied with the product e Connect the water inlet hose directly to the water tap Pressure coming from the tap should be minimum 0 3 and maximum 10 bars If the water pressure exceeds 10 bars a pressure relief valve should be installed in between Use a screw on hose connector to connect the water inlet hose to a water tap with a inch external thread If required use a filter insert to filter deposits from the pipes g El 112 B 3 Sain 10 g 3 4 Sy OOOO e Open the taps completely after making the connections to check for water leaks 8 A For your safety close the water inlet tap completely after the washing programme is over Connection to the drain Water discharge hose
38. odel This accessory located at the lower basket of the machine allows you to easily wash pieces such as extra glasses long ladles and bread knives a gt Sinan Min Kf SS Veto To close the racks 1 Fold the rack A 2 Slide the rack up B 3 Put the rack in vertical position C 4 Slide the rack down and lock it with the tabs D i Perform the same process in reverse order to open the racks To adjust the height of the racks 1 Fold the rack E 2 Slide the rack up F 3 Open the rack at the desired level N Make sure that the impeller does not touch the dishes you placed on the racks Upper basket height adjustable rack depends on the model Use the lower and upper parts of the height adjustable racks in the upper basket of the machine by sliding them down or up according to the heights of the glasses cups or etc A B C Upper basket drawer depends on the model You can easily place additional desert spoons small forks and knives into the basket drawer installed to the upper basket of your machine Upper basket glass support piece depends on the model When placing long stemmed glasses or wine glasses do not lean them against other pieces but to the edge of the basket or to the rack 1 Do not lean long glasses against each other They can move and get dama
39. r space etc in a cleaner manner while placing your dishes to the lower basket and free up space for your dishes in different sizes Silverware basket piece depends on the model You can place your forks spoons and etc to upper basket with the additional piece in the figure 18 EN Collapsable lower basket wires spaces by folding each wire individually 2 pieces or all of them at once Lay the foldable depends on the model wires down by pressing on the latch The two piece foldable wires located A at the lower basket of the machine are designed for an easier placement of large pieces such as pans bowls etc 1 2 You can create larger spaces by folding each wire individually or all of them at once Lay the foldable wires down by pressing on the latch A Lower basket bottle wire depends on the model The bottle wire is designed for easier washing of long pieces with wide mouths You may take out the bottle wire from the basket when not in use by pulling it out from both sides H Collapsable lower basket wires 4 pieces depends on the model The four piece foldable wires located at the lower basket of the machine are designed for an easier placement of large pieces such as pans bowls etc 1 2 3 4 You can create larger Lower basket multipurpose height adjustable service rack depends on the m
40. rienced people including children unless they are attended by a person who will be responsible for their safety or who will instruct them accordingly for use of the product Children s safety Electrical products are dangerous for the children Keep children away from the product when it is in use Do not let them to tamper with the product Do not forget to close the door of the product when leaving the room where it is located Store all detergents and additives in a safe place away from the reach of the children 6 EN EI Installation Refer to the nearest Authorised Service Agent for installation of your product To make the product ready for use make sure that the electricity tap water supply and water drainage systems are appropriate before calling the Authorised Service Agent If they are not call a qualified technician and plumber to have any necessary arrangements carried out GJ Preparation of the location and electrical tap water and waste water installations at the place of installation is under customer s responsibility Installation and electrical connections must be carried out by the Authorised Service Agent Manufacturer shall not be held liable for damages that may arise from procedures carried out by unauthorised persons Prior to installation visually check if the product has any defects on it If so do not have it installed Damaged products cause risks for your safety Make sur
41. s completed Slightly open the door and wait for evacuation of the steam inside for a while Unload the dishes after the pieces cool down to a touchable level Start unloading process from the lower basket Thus dropping of water remained on a piece at upper basket onto the pieces at lower basket is prevented Selected programme is unsuitable gt gt gt Since rinsing temperature is low at programmes with short duration drying performance will also be low Select programmes with longer duration for a higher drying performance Surface quality of the kitchen utensils is deteriorated gt gt gt Desired washing performance can not be obtained at kitchen utensils with deteriorated surfaces and it is not suitable to use such utensils in terms of hygiene as well Also water can not flow easily on deteriorated surfaces It is not recommended to wash such kitchen utensils in dishwasher G Itis normal that drying complaints can be experienced with Teflon kitchen utensils It is associated with the structure of Teflon Since the surface tensions of Teflon and water are different water droplets will remain as beads on the Teflon surface Tea cafe or lipstick stains remain on dishes Selected programme is unsuitable gt gt gt Select a programme with a higher temperature and cycle time Surface quality of the kitchen utensils is deteriorated gt gt gt Tea and cafe stains or other dye spots may not be cleaned in dishwasher when t
42. shing process gt gt gt Pay attention to add detergent shortly before start up of the washing Opening of the detergent dispenser lid is prevented during washing gt gt gt Place the dishes in a way that will not prevent the detergent dispenser lid from opening and the water going into the machine from impellers Detergent is stored under unsuitable conditions gt gt gt f you are using powder detergent do not store the detergent package in humid places Keep it in a closed container if possible For ease of storing we recommend you to use tablet detergents Impeller holes are clogged gt gt gt Lower and upper impeller holes might be clogged with food remnants such as lemon pips Clean the impellers regularly as illustrated in section Cleaning and Care Decorations and ornaments on kitchen utensils are being erased GJ Decorated glasses and decorated luster porcelains are not suitable for washing in the dishwasher Manufacturers of glassware and porcelain tableware items do not recommend washing such kitchen utensils in the dishwashers either Dishes are scratched GJ Kitchen utensils that contains or are made of aluminum should not be washed in dishwasher Salt leakage exists gt gt gt Pay attention not to spill salt around the salt filling hole while adding salt Spilled salt can cause scratches Make sure that the salt reservoir lid is tightly closed after finishing the filling process Run the prewash programme
43. ss dishwasher standardloading com Do not forget to provide the code stock and serial numbers of the product to be tested in your request e mail along with your contact information Code stock and serial numbers of the product is located on the type label attached to the side of the door 4 EN 2 Important safety instructions This section contains safety instructions that will help to get protected from risk of personal injury or property damage Failure to follow these instructions shall void all warranties General safety Never place the product on a carpet covered floor otherwise lack of airflow beneath the product will cause electrical parts to overheat This will cause problems with your product Do not operate the product if the power cable plug is damaged Call the Authorised Service Agent Connect the product to a grounded outlet protected by a fuse complying with the values in the Technical specifications table Do not neglect to have the grounding installation made by a qualified electrician Manufacturer shall not be liable for any damages that will arise when the product is used without grounding in accordance with the local regulations The water supply and draining hoses must be securely fastened and remain undamaged Unplug the product when not in use Never wash the product by spreading or pouring water onto it There is the risk of electric shock Never touch the plug with wet hands N
44. the program does not start within 30 seconds after the machine is turned on by pressing the On Off button e If you wait more than 30 seconds when the machine is stopped during washing Key lock is deactivated automatically when the program is over If you press the touch key at the end of the program machine will display the Press to wash message If the machine is left to wait in this status key lock will be activated after 30 seconds and Key Lock Activated will be displayed If you press the button when the key lock is active Key Lock Active is 27 displayed and if you press the key for a second time Press for 5 sec is displayed You must press Start Pause Cancel key until the Key Lock Deactivated message is displayed to deactivate the key lock When you keep the Start Pause Cancel key pressed the countdown of 5 seconds starts and the following messages are displayed consecutively Unlock the keylock 5 Unlock the keylock 4 Unlock the keylock 3 Unlock the keylock 2 Unlock the keylock 1 Keylock deactivated Key will remain locked if you release the key before the Keylock deactivated is displayed Key lock is deactivated when the Keylock deactivated message is displayed You can press the Start Pause Cancel key to perform the operation you want after the key lock is deactivated Stopping the machine Deactivate the key lock first if you
45. vice Agent Never try to repair a nonfunctional product yourself 40 EN EN 17 7942 01 00_AC_TT
Download Pdf Manuals
Related Search