dvr1a - Eclats antivols
Contents
1. DVR1A DIGITAL VIDEO RECORDER 1 Introduction 4 Thank you for choosing the DVR1A Read the manual carefully before bringing this device into service The DVR1A converts analogue NTSC or PAL video to digital images and records them on a removable hard disk drive Digitally recorded video has several advantages over analogue video recorded on tape There is no need to adjust tracking Digital video can be indexed by time schedule or events and you can instantly view video after selecting the time or event You can freeze frames fast forward fast reverse slow forward and slow reverse without image streaking or tearing It can be used as a replacement for a time lapse VCR in a security installation a Safety Prescriptions Handle this device with care Do not expose this device to direct sunlight Do not use this device near water and protect it against any possible contact with water Do not unplug the power connector before you ve correctly switched the device off Use this device solely with the included power adapter Unauthorised attempts to repair may result in fire electroshock or other hazards A qualified technician should service this device Do not switch the power ON and immediately 3 sec OFF again Use a type of power source as indicated on the manufacturer s label This device should be installed by a qualified person and conform to all local codes b Features This device replaces a traditional time2. it becomes low and will stop all alarm functionalities PIN 14 ALARM INPUT By connecting ALARM INPUT pin 14 to GND pin 9 the DVR1A will start recording and the buzzer will be on During normal functioning this signal is high when there is an incoming alarm signal it becomes low the device will start recording and the buzzer will be on PIN 15 Com During normal functioning COM is connected with NC and not with NO When there is an alarm trigger COM disconnects from NC and connects with NO DVR1A 6 GB 4 System Set up a Open Main Menu Password 0000 Press the MENU button on the front of the device The screen you see on the right will be displayed You will need to enter a password to access the main menu Press lt 4 or to change digits and A or W to change the value of the digit Press ENTER to confirm the password e g password 0000 default 0000 After entering the correct password and confirming it by pressing ENTER this display will appear b System Menu Press the MENU button on the front of the device enter the password and confirm it by pressing ENTER cf 4a Open Main Menu above Press A or Y until System is selected cf figure on the right System gt Buzzer On HDD Overwrite No Press ENTER to enter the system set up menu The screen as Date Display Y M D h iia Hone wil baclisnleved Date 2002 JUL 14 SUN SNOWN on the right will be displayed Time 22 38 29 New Passwo
3. switch pages 8 events per page and select the desired recording with A or Y Press ENTER to play the selected recording 4 Search a recording by time Press the search button and A or to select Time Search Press ENTER to obtain the search screen and a screen as shown on the right will be displayed Press lt 4 or to switch parameters and A or W to change the parameter value Press ENTER to play the selected recording If there is no recording available for the time provided the screen will display Time Not Found e Video Loss gt Last Record Full List Alarm List Time Search M 2002 JAN 01 01 02 03 M 2002 JAN 01 01 02 03 A 2002 JAN 01 01 02 03 T 2002 JAN 01 01 02 03 E 2002 JAN 01 01 02 03 M 2002 JAN 01 01 02 03 E 2002 JAN 01 01 02 03 T 2002 JAN 01 01 02 03 lt Page Up gt Page Down A 2002 JAN 01 01 02 03 A 2002 JAN 01 01 02 03 A 2002 JAN 01 01 02 03 A 2002 JAN 01 01 02 03 A 2002 JAN 01 01 02 03 A 2002 JAN 01 01 02 03 A 2002 JAN 01 01 02 03 A 2002 JAN 01 01 02 03 Play Time 2002 JAN 01 18 The screen will display Video Loss if the DVR1A does not receive a video signal f Key Lock Press MENU and ENTER simultaneously to lock the control keys Press MENU and ENTER simultaneously to unlock the control keys DVR1A 15 GB 6 Troubleshooting What may appear as a malfunction of the device may not be that serious at all and can be easily corrected Check the table below before co
4. time HH MM Press A or Y to set the recording end time 5 Press lt or to select the number the images per second IPS Press A or to set the number of IPS NTSC 1 2 4 8 15 30 60 PAL 1 2 3 6 12 25 50 OFF not activated REMARK Recording quality and format are determined in the Record menu 6 Press MENU to confirm current settings and ENTER to go to the next programming line 7 Press A or to select Timer Enable Yes to activate the programmed settings No to ignore the programmed settings Press MENU to confirm the current set up and return to the previous menu Press MENU again to exit and close the Timer menu o DVR1A 9 GB Press the MENU button on the front of the device enter the password and confirm it by pressing ENTER cf 4a Open Main Menu on p 7 Press A or Y until Record is selected cf figure on the right Press ENTER to enter the recording menu A screen as shown d Recording Mode Set Up 1 Enter Record menu Record on the right will be displayed gt Record IPS 60 oR PONS Ooch Record Quality Normal Record Mode Frame 2 IPS Set Up images per second Press A or W to select Record IPS and press ENTER to open the IPS set up Press A or to set the IPS recording speed 60 30 15 8 4 2 1 NTSC or 50 25 12 6 3 2 1 PAL Press MENU to confirm the current set up and return to the previous menu Press MENU again to exit and close the record m
5. 0 seconds before removing it DVR1A 16 GB
6. B it means that there is 32GB recording capacity left on the HDD DVR1A 13 GB 3 Programmed Recording The DVR1A will follow the timer set up to record and the 2002 JAN 01 01 02 03 recording speed amp quality will be as set in the TIMER menu TO OW T Timer recording 53 recording OW HDD overwrite 32GB if the OW location shows 32GB it means that there is 32GB recording capacity left on the HDD 4 Manual Recording 2002 JAN 01 01 02 03 MEG Ow M Manual recording G recording OW HDD over write 32GB if the OW location shows 32GB it means that there is 32GB recording capacity left on the HDD c Playback Press PLAY the DVR1A will go into play mode and will start playing the last recording 1 Fast Forward F F amp Fast Rewind F R e Press PLAY then press gt for fast forward searching Press once for double speed press twice for quadruple speed 3 times for 8x 4 times for 16x and 5x for 32x maximum speed e Press PLAY then press lt lt for fast rewind searching Press once for double speed press twice for quadruple speed 3 times for 8x 4 times for 16x and 5x for 32x maximum speed 2 Slow Forward S F amp Slow Rewind S R e Press PLAY then press SLOW for slow play Press gt B once for half speed press twice for quarter speed 3 times for 1 8x 4 times for 1 16x and 5x for 1 32x minimum speed e Press PLAY th
7. Menu on p 7 gt Event Press A or Y until Event is selected cf figure on the right Press ENTER to see the entire list of events A screen as PWR 2002 JAN 01 03 00 00 shown on the right will be displayed VLS 2002 JAN 01 01 02 04 HDD 2002 JAN 01 01 02 03 PWR 2002 JAN 01 01 02 02 Press lt 4 or to switch pages 8 events on 1 page and press VLS 2002 JAN 01 01 02 01 A or Y to select the desired event Press ENTER to play it HDD 2002 JAN 01 01 02 00 lt Page Up gt Page Down HDD HDD error time VLS video loss time PWR recovery time after power shutdown e g power shut down at 01 00 and power recovery at 03 00 The display indicates that the device restarted at 03 00 after a power shutdown DVR1A 12 GB 5 Operation a Power ON Before turning power ON make sure the HDD has been locked and the power LED is red After pressing the POWER button the POWER LED will turn to orange and all the other LEDs will turn RED except the LED for HDD The screen will display HDD Detecting power on period will be approx 5 to 15 seconds If HDD is set as master the screen will display HDD Master Connect If HDD is set as slave the screen will display HDD Slave Connect In order to shorten the power on running time we suggest setting the HDD as master by means of the jumper on the HDD itself When the DVR1A has powered on completely the POWER LED will turn to green b Recording Your DVR1A offers a variety
8. by pressing ENTER cf 4a Open Main Menu on p 7 Press A or Y until Remote is selected cf figure on the right Press ENTER to enter the remote menu A screen as shown on the right will be displayed Remote gt Remote Mode RS 232 2 Remote Protocol Mode Set Up Baud Rate 9600 ID 000 Press A or W to select Remote Mode and press ENTER Press Aor Yto select the protocol RS 232 or RS 485 Press MENU to confirm the current set up and return to the previous menu Press MENU again to exit and close the remote menu PANS 3 Remote Protocol Transmitting Baud Rate Set Up Press A or Y to select Baud Rate and press ENTER Press A or to set the baud rate 115200 57600 19200 9600 480 3600 2400 1200 Press MENU to confirm the current set up and return to the previous menu Press MENU again to exit and close the remote menu PAM 4 Remote Protocol ID Set Up You can use the RS232 remote protocol to control more than 1 DVR1A The ID number can range from 000 to 999 1 Press A or W to select ID and press ENTER 2 Press A or to set numerical number and press lt or to move digit location 3 digits 3 Press MENU to confirm the current set up and return to the previous menu 4 Press MENU again to exit and close the remote menu M g Event List Ss Record Press the MENU button on the front of the device enter the Sale password and confirm it by pressing ENTER cf 4a Open Main System
9. en press SLOW for slow play Press lt 4 lt 4 once for half speed press twice for quarter speed 3 times for 1 8x 4 times for 1 16x and 5x for 1 32x minimum speed 3 Pause Press PLAY then press PAUSE the image will be paused 4 Stop Press STOP and the DVR1A will stop all actions and display the incoming signal 5 Image by image e Press play then press PAUSE the image will be paused Then press gt to go to the next image Keep gt gt pressed for faster image progression e Press PLAY then press PAUSE the image will be paused Then press lt 4 lt to go to the previous image Keep lt 4 lt pressed for faster image progression DVR1A 14 GB d Search 1 SEARCH menu last recording Press the search button a screen as shown on the right will be displayed Press ENTER to play the last recording 2 Full list of recordings Press the search button and A or to select Full List Press ENTER to obtain the full list and a screen as shown on the right will be displayed Press lt 4 or to switch pages 8 events per page and select the desired recording with A or Y Press ENTER to play the selected recording M manual Recording A Alarm Recording T Timer Recording E External Recording 3 Recorded Video in Alarm List Press the search button and A or to select Alarm List Press ENTER to obtain the alarm list and a screen as shown on the right will be displayed Press lt 4 or gt to
10. enu 3 Recording Quality Set Up Press A or W to select Record Quality and press ENTER to open the record quality set up Press A or to set the recording quality level best high normal basic Press MENU to confirm the current set up and return to the previous menu Press MENU again to exit and close the record menu 4 Recording Mode Set Up Press A or Y to select Record Mode and press ENTER to open the recording mode set up Press A or to set the recording mode frame field Press MENU to confirm the current set up and return to the previous menu Press MENU again to exit and close the record menu DVR1A 10 GB Press the MENU button on the front of the device enter the password and confirm it by pressing ENTER cf 4a Open Main Menu on p 7 Press A or Y until Alarm is selected cf figure on the right e Alarm Set Up 1 Enter Alarm Menu Alarm gt Alarm Enable Yes Press ENTER to enter the alarm menu A screen as shown on Alarm Duration 1 MIN the right will be displayed Record IPS 60 Ooch ONES Em ORNS Ars PONS Record Quality Normal Record Mode Frame 2 Alarm Enable ON OFF Set Up Press A or W to select Alarm Enable and press ENTER to open the alarm enable set up Press A or Y to set the alarm ON or OFF Press MENU to confirm the current set up and return to the previous menu Press MENU again to exit and close the alarm menu 3 Alarm Duration Set U
11. f a test during which regular TV programs were recorded NTSC SYSTEM 24hr 48hr 180hr 360hr Normal 24hr 48hr 96hr 180hr 120GB PAL SYSTEM se o y as y a So e yo a S a2 S 1 rec quality 6 24hr 48hr 180hr 360hr 720hr quality j 101hr 203hr 405hr 608hr 1216hr 168hr 338hr 675hr 1013hr 2025hr HDD type 120GB DVR1A 4 GB b Control Panel Description 1 2 3 4 5 6 PAUSE Up ENTER SEARCH 1 HDD HDD is activated 2 HDD FULL HDD is full 3 ALARM alarm is armed when alarm is triggered LED is flashing 4 TIMER the device is programmed to record 5 PLAY recorded material is being reproduced 6 REC the device is recording 7 MENU Press MENU and enter the password default 0000 to access the main menu 8 ENTER Press ENTER to confirm data or a selection 9 SEARCH Press SEARCH to search a video fragment by recording time 10 SLOW Press SLOW to slow down the play speed 11 Controls for video playback gt PLAY to play recorded video E STOP to stop playback I PAUSE to pause the fragment 44 REW for fast rewind in PLAY mode or to go back to the previous image in PAUSE Speed can be adjusted by pressing the REW button several times gt FF Right for fast forward in PLAY mode or to move on to the next image in PAUSE Speed can be adjusted by pressing the REW button several times 12 REC Press this button to start recording 13 POWER Press this button to power on and press again to p
12. he DVR keypad DATA REMOTE PROTOCOL using 8 bit data 1 start bit 1 stop bit ACT COH ID FUNCTION STOP FFH 7FH FUNCTION CODE ASCII FUNCTION CODE ASCII MENU M DOWN STOP N M OO N ENTER ENTER LEFTJF F LOER Pose E SEARCH RIGHT F R SLOW PLAY UP PAUSE RECORD DVR1A 3 GB 3 Configuration a Installing HDD 1 HDD Description 2 1 3 4 1 Handle of the HDD tray 2 Tray lock In position A cf drawing on the right the tray is locked and cannot be removed A In position B the tray is unlocked and can be removed The key lock must be in position A before you switch on the device if not the hard disk drive cannot be used in a regular way Power indicator green LED lights up when the device is switched on B 4 HDD access indicator yellow LED oo 2 Installing the Hard Drive into the Tray Unlock the tray lock pull out the handle and pull the tray out of the device Push the release latch at the left OPEN to slide the top cover backwards and remove it Connect the DC power cable and IDE cable to the HDD Insert the HDD in the tray and secure the HDD through the screw holes in the sides Put the top cover back on the tray and slide it forward to secure it Slide the tray back into the device 3 Max Recording Time The recording time depends on the recording speed and quality Please refer to the tables below Note these data are the results o
13. igger recording terminal of a multiplexer in order to synchronise recording signals The default mode of this signal is low PIN 5 ERROR OUT When a HDD error occurs this pin will send a signal During normal functioning this signal is high when a HDD error occurs it becomes low PIN 6 REC START This pin can accept the trigger signal from an external device to start recording Normally this signal is high when it becomes low the DVR1A starts recording when it becomes high again the recording stops PIN 7 EXTERNAL ALARM NC PIN 8 EXTERNAL ALARM NO During normal functioning COM is connected with NC and not with NO When there is an alarm trigger COM disconnects from NC and connects with NO PIN 9 GND GROUND PIN 10 RS485 B PIN 11 RS485 A The device can be controlled remotely by an external device or control system such as a control keyboard using RS485 serial communications signals PIN 12 DISK FULL If you ve connected several DVR1A s and the hard disk of the operating one is full it will send a signal to the next device which will start recording During normal functioning this signal is high when the HDD is full it becomes low PIN 13 ALARM RESET By connecting ALARM RESET pin 13 to GND pin 9 you can disable the ALARM An external signal to ALARM RESET pin 13 can be used to reset both ALARM OUTPUT signal and DVR1A s internal buzzer During normal functioning this signal is high when the alarm reset is triggered
14. lapse VCR and is compatible with most multiplexers and quad processors Compatible with NTSC PAL systems Recording speed 1 60 images sec NTSC or 1 50 images sec PAL Recording quality best high normal basic resolution Quick search modes search a fragment by time event or alarm list Fast forward or reverse from 2X up to 32X and slow forward or reverse from 1 2X to 1 32X Adjustable time display format Password protection Automatic recording possible upon reception of an alarm signal or after detection of video loss Alarm output audio signal possible upon reception of alarm signal Programmed recording Power off protection the device cannot be switched off with the POWER button during recording RS232C control port you can connect the DVR1A to external devices through an RS 232C interface When the HDD is full the device stops recording In overwrite mode the device continues recording and overwrites the oldest recordings DVR1A 1 GB c Specifications Video Format HDD Storage Record Mode Search Function RS232 On Screen Display OSD Security Video Input Video Output Video Resolution Video Compression Display Refresh Rate Record Refresh Rate Alarm Input Alarm Output Video Loss Detection Time Display Format Power Source Power Consumption Dimensions Weight Operating Temperature 2 Installation a Contents HDD tray tray key power cable user manual single channel digital video
15. m load default system settings Late Boe a However Date Time amp Password set up will not be changed Date 202 JULA 4 SUN No not to reset the system Time 22 38 29 3 Press MENU to confirm the current set up and return to the previous menu New Password Xxxx Clear HDD No 4 Press MENU again to exit and close the system set up menu gt System Reset No Note If operation without any action until 60 seconds it will close the set up mode DVR1A 8 GB c Timer Programming 1 Enter Timer Menu Press the MENU button on the front of the device enter the password and confirm it by pressing ENTER cf 4a Open Main Menu on p 7 Press A or Y until Timer is selected cf figure on the right Timer Day Start End Daily 00 00 00 00 Daily 00 00 00 00 Press ENTER to enter the timer menu The screen as shown on Ra on ae oe the right will be displayed Daily 00 00 00 00 Daily 00 00 00 00 Daily 00 00 00 00 Timer Enable No 2 Timer Recording Set Up 1 Press ENTER to set the day selection of the first line 2 Press A or to select the day set up Daily every day SUN Sunday MON _ Monday TUE Tuesday WED Wednesday THU Thursday FRI Friday SAT Saturday MO FR Monday to Friday SA SU Saturday amp Sunday JAN 01 special date 3 Press lt 4 or to select the recording start time HH MM Press A or Y to set the recording start time 4 Press lt or to select the recording end
16. ntacting your DVR1A dealer SOLUTION Check power source cable connections Confirm that there is power at the outlet Check if it is under key lock mode Press MENU and ENTER simultaneously to skip the key lock mode No recorded video Check if the HDD has been installed properly Record enable does not working Check if record enable is set to YES No live video Check camera video cable and connections Check monitor video cable and connections ae Confirm that the camera is powered Check camera lens setting REC LED is ON but the device does not record Device is in Timer mode It will only record during assigned time 7 Compatible Brands a Compatible Multiplexers Manufacturer Model System Test Result AV TECH AVCTOIN NTSC AV TECH AVC707P PAL AV TECH AVCTOGN NTSC ROBOT Mx99e NTSC b Compatible HDD Brands Appendix B Manufacturer Model Capacity Rotation 7200rpm 7200rpm 7200rpm 7200rpm Maxtor DiamondMax Plus 9 Model 6Y120L 120GB 7200rpm Seagate Barracuda ATA IV ST340016A 40GB 7200rpm Barracuda ATA V ST3120023A 120GB 7200rpm Western Digital Caviar WD400BB 00BSA0 40GB 7200rpm Western Digital Caviar WD400EB 00CPFO 40GB 5400rpm DiamondMax 536DX 60GB 4W060H4 60GB 5400rpm Remarks e The listed brands have been tested and are compatible with the DVR1A Do not use other brands than these e In order to avoid damage to the HDD leave the device switched off during at least 6
17. of flexible recording modes You can set it up to record continuously or programmed or only to record events you can even set the recording speed and resolution All these options are set through the system menu If there should be a power cut during recording the device will automatically resume recording when the power returns The original recording set up will be respected There are 4 recording modes for your device alarm recording mode external trigger recording mode programmed recording mode and manual recording mode All recording modes are described here 1 Alarm Recording When the DVR1A receives an alarm input it will start to record immediately The recording speed amp quality will be as set in the alarm recording mode set up 2002 JAN 01 01 02 03 The screen will be as displayed on the right AGa OW A alarm trigger 53 recording OW HDD overwrite 32GB if the OW location shows 32GB it means that there is 32GB recording capacity left on the HDD 2 External Trigger Recording The DVR1A can be programmed to start recording when it receives a trigger from an external device When a REC START command is received RS232 pin 6 the recording will start The recording speed and quality will be as set in the recording mode set up The screen will be as displayed on the right 2002 JAN OT ee E External trigger recording oe O9 recording OW HDD overwrite 32GB if the OW location shows 32G
18. ower off c Back Panel Description 1 POWER connect the provided adapter to this connector and plug it into the mains 2 VIDEO IN to connect to a video source such as a quad a multiplexer or a camera 3 VIDEO OUT to connect to a monitor or the video input of a quad or multiplexer 4 AUDIO OUT to connect to a monitor 5 AUDIO IN to connect an audio source such as a microphone 6 External RS232 Alarm in and output the device can be controlled remotely by an external device or trigger mechanism The connections should be established as follows DVR1A 5 GB 25 pin COM port 9 pin COM port _ 1 COMPUTER F RS232 TX PED RX GND IRS R5232 RX RS485 B paa E VIDEO LOSS VIDEO LOSS R5485 A RS485 4 DISK FULL DISK FULL ERROR OUT ERROR OUT ALARM RESET ALARM RESET om REC STAR op ALARM INPUT ALARM INPUT O EXTERNAL ALARM NC EXTERNAL ALARM NC O 7 EXTERNAL ALARM COM EXTERNAL ALARM COM 15 Oe EXTERNAL ALARM NO EXTERNAL ALARM NO a8 eas PSS G8 Koy EE Oe PIN 1 RS232 TX RS 232 PIN 2 RS232 RX RS 232 This device can be controlled remotely by an external device or control system such as a control keyboard using RS 232 serial communications signals PIN 3 VIDEO LOSS When video loss occurs a signal is sent to trigger another device During normal functioning this signal is high when video loss occurs it becomes low PIN 4 SWITCH OUT Connect this pin to the VCR tr
19. p Option Press A or W to select Alarm Duration and press ENTER to open the alarm enable set up Press A or to set the alarm duration 1 min 3 min 5 min 10 min 30 min 1 hour always Press MENU to confirm the current set up and return to the previous menu Press MENU again to exit and close the alarm menu 4 Alarm Recording Speed Set Up IPS Press A or W to select Record IPS and press ENTER to open the IPS set up Press A or W to set the recording speed IPS 60 30 15 8 4 2 1 NTSC or 50 25 12 6 3 2 1 PAL Press MENU to confirm the current set up and return to the previous menu Press MENU again to exit and close the alarm menu 5 Alarm Recording Quality Set Up Press A or W to select Record Quality and press ENTER to open the recording quality set up Press A or to set the recording quality level best high normal basic Press MENU to confirm the current set up and return to the previous menu Press MENU again to exit and close the alarm menu 6 Alarm Recording Mode Set Up Press A or to select Record Mode and press ENTER to open the record mode set up Press A or W to choose the recording mode frame field Press MENU to confirm the current set up and return to the previous menu Press MENU again to exit and close the alarm menu DVR1A 11 GB f Remote Protocol Set Up 1 Enter Remote Menu Press the MENU button on the front of the device enter the password and confirm it
20. rd xxxx Clear HDD No System Reset No 1 Internal Alarm Buzzer ON FF Set Up Press A or W to choose Buzzer and the ENTER button to open the buzzer menu Press A or W to switch the alarm buzzer ON OFF On buzzer ON off buzzer OFF Press MENU to confirm the current set up and return to the previous menu Press MENU again to exit and close the system set up menu elon 2 HDD Overwrite Set Up Press A or W to choose HDD Overwrite and the ENTER button to open the HDD Overwrite menu 2 Press A or W to choose HDD Overwrite Yes No Yes HDD Overwrite on When the HDD is full the device will start overwriting the oldest data No HDD Overwrite off When the HDD is full the device will stop recording Press MENU to confirm the current set up and return to the previous menu 4 Press MENU again to exit and close the system set up menu w DVR1A 7 GB 3 On Screen Display for Date 1 Press A or W to choose Date display and the ENTER button to open the Date display menu 2 Select a format with A or W Y M D year month day M D Y month day year D M Y day month year or OFF date is not displayed Press MENU to confirm the current set up and return to the previous menu 4 Press MENU again to exit and close the system set up menu wo 4 System Date Set Up 1 Press A or W to choose Date and the ENTER button to open the system date menu 2 Press A or W to change the value and lt or to move
21. recorder NTSC EIA or PAL CCIR IDE type UTMA 66 or above 1 removable HDD supported manual alarm external timer Date amp time event alarm searching yes yes password protection 1 video input composite 1Vp p 75Q BNC 1 video output composite 1Vp p 75Q BNC 720 x 576 PAL 720 x 486 NTSC wavelet 60ips NTSC 50ips PAL 60ips NTSC 50ips PAL TTL input high 5V low GND COM NO yes yes AC 100 240V 10 switching adapter lt 27W 380 x 270 x 65mm W x L x H 5 2kg 10 40 C rack mounting kit optional demounted 15 pin connector b Connection with a single camera Video Camera 1 AUDIO IN DVR1A 2 GB c Connection with a multiplexer Video Camera 146 2 as A ey E Alarm Sensor Sa San PC eG Ea E y en Tee etre sere ce eae a RS232 l pe el vo VCR OUT RER e FA AUDIO IN 3 ENE 7 eG ti a a i Baa lt Bese cae is Se Smee ae VIDEO OUT VCR IN AUDIO OUT d Rack Mount Installation The device can be mounted in a rack with the optional mounting equipment Fix the smallest side of the mounting plates with the small holes to the device screw holes are provided at the sides and then fix the device to the rack e RS232 Remote Protocol You can use the PC keyboard to simulate t
22. to the previous or next value 3 Press MENU to confirm the current set up and return to the previous menu 4 Press MENU again to exit and close the system set up menu 5 System Time Set Up 1 Press A or to choose Time and the ENTER button to open the system time menu 2 Press A or W to change the value and lt or to move to the previous or next value 3 Press MENU to confirm the current set up and return to the previous menu 4 Press MENU again to exit and close the system set up menu 6 Change Password default password 0000 1 Press A or W to choose New password and the ENTER button to open the password menu 2 Press A or W to change the value and lt or to move to the previous or next value 3 Press MENU to confirm the current set up and return to the previous menu 4 Press MENU again to exit and close the system set up menu 7 Clear HDD Yes No Set Up 1 Press A or Y to choose Clear HDD and the ENTER button All Data in HDD 2 Press or lt to choose between Yes and No MIS ese eared i Are you sure Yes press to clear the HDD 4 No gt Yes No press lt NOT to clear the HDD 3 Press MENU to confirm the current set up and return to the previous menu 4 Press MENU again to exit and close the system set up menu 8 System Reset Set Up 1 Press A or Y to choose System Reset and the ENTER button System 2 Press A or W to choose system reset set up YES or NO Buzzer On Yes to reset the syste
Download Pdf Manuals
Related Search