Premier Reticle Heritage 5
Contents
1. PREMIEQQRETICLES Heritage 5 25 X 56 User Guide American Company American Product The Premier Heritage 5 25x56 carries a lifetime warranty If you have any questions or would like more information regarding your scope please contact us using the information below For a more comprehensive user manual one can be downloaded from our website Caution Ensure all manufacturer instructions are followed when mounting this optic to a rifle in order to prevent damage to the optic rifle and or operator Also do not look through the optic directly at the sun or laser light devices as doing so could result in permanent eye injury 175 Commonwealth Ct Winchester VA 22602 USA Phone 540 868 2044 Specifications Total Elevation Range 30 mrad 103 MOA Windage Knob 12 mrad 41 MOA Width 4 02 Diopter Range 3 to 2 5 Weight 39 oz Exit Pupil 11 2mm 2 24mm Click Value 0 1 mrad 36 100 yards Elevation Knob 28 mrad 96 MOA Gen II Mil Dot Reticle The Gen II Midot reticle is installed in the first focal allowing range estimation and trajectory compensation to be performed at any magnification level The cick values match the reticle meaning that ten clicks of the elevation or windage knob will equal one mil at any distance This can greatly reduce the time necessary to make corrections for zeroing or target engagement as the correction noted while looking through the scope is the correction that needs to2. to close If excessive pressure is necessary to close the toggle lift it and turn counter clockwise 1 16 of a tur then retry Too litle pressure on the toggle can result in the toggle becoming loose while tuming the knob which can result in no correction boing made despite audible clicks and clunks Lens Cleaning 1 Use a soft brush to remove dirt and dust from the lens 2 Use a lens pen or an optical quality solution to clean the lens using a spiral motion starting at the center and going out 3 Remove any left over residue or streaks trom the glass using a lens pen or piece of lens paper Premier Heritage Lever Lock Gen 2 Mildot and Gen 2 XR are all trademarks of Premier Reticles Ltd Gen 2 Mildot is protected under US Patent 16 729 062 MTC technology is used by permission and is the property of US Optics US Patent 7 415 731 ali rights reserved
3. be dialed in Below are some subtensions of the Gen I reticle Not To Scale ER A F S 0 2 mil Adjust Diopter 1 Loosen the ocular lock ring by tuming it counter clockwise 2 Look through the scope and adjust the ocular until the reticle comes into focus 3 Look away and look back at the reticle to ensure the image is stil crisp and clear from edge to edge 4 Tighten the ocular lock ring by turning it clockwise until snug The diopter will only focus the reticle to the eye Adjust Magnification 1 To increase magnification rotate the power adjustment ring counter clockwise 2 To decrease magnification rotate the power adjustment ring clockwise Mumination 1 Grasp the knob and pull away from the scope to enable the illumination function 2 Rotate the knob clockwise and select one of the eleven intensity settings The illumination will shut otf between intensity settings however the barrel cannot be pushed back in 3 To tum off the illumination rotate the knob counter clockwise until the knob hits the stop and then push the ilumination knob back in Battery Cover Changing the battery 1 Use a coin or similar object to insert into the slot on the battery cover 2 Rotate counter clockwise until the cover can be removed to expose the battery 3 Remove the battery and replace with a fresh CR2032 coin cell battery 4 Replace the battery cover and rotate clockwise until snug Parallax A
4. djustment The scope can compensate for parallax from 50 meters to infinity Adjust Parallax 1 To adjust the parallax for farther objects rotate the knob clockwise until the target and reticle are in focus To adjust the parallax for closer objects rotate the knob clockwise until the target and reticle are in focus ElevationWindage Knob Operation The elevation and windage knobs are single turn with 0 1 mrad clicks and a noticeable clunk every full mil The elevation knob also has a zero stop approximately 5 mil below 0 Elevation 1 To increase elevation adjustment rotate the elevation knob counter clockwise 2 To decrease elevation adjustment rotate the elevation knob clockwise Windage 1 For right windage rotate the knob counter clockwise 2 For left windage rotate the knob clockwise Zeroing out the knobs 1 Use a cartridge case or other object to lit the toggle on top of the elevation and windage knobs 2 Flip the toggle 180 so the toggle is upside down ww 3 Grasp the knob and reset it to zero While turning the knob it wil still have audible clicks and clunks however there will be no change in zero 4 Once the knob is reset to zero retum the toggle to the upright position The toggle will be in the optimal postion when steady pressure is needed to fully close it If the toggle is not in the optimal position then the toggle will not clase or it will require excessive pressure
Download Pdf Manuals
Related Search