Manual - Gefen
Contents
1. DMI Over RGB EXT HDMI 5BNC User Manual ASKING FOR ASSISTANCE Technical Support Telephone 818 772 9100 800 545 6900 Fax 818 772 9120 Technical Support Hours 8 00 AM to 5 00 PM Monday thru Friday Pacific Time Write To Gefen LLC c o Customer Service 20600 Nordhoff St Chatsworth CA 91311 www gefen com support gefen com Notice Gefen LLC reserves the right to make changes in the hardware packaging and any accompanying documentation without prior written notice HDMI Over RGB is a trademark of Gefen LLC 2010 Gefen LLC All Rights Reserved All trademarks are the property of their respective owners Rev B1 CONTENTS Introduction Operation Notes Features Sender Panel Layout Sender Panel Descriptions Receiver Panel Layout Receiver Panel Descriptions Connecting And Operating The HDMI Over RGB Troubleshooting The HDMI Over RGB 0 Specifications ON Oo FWD 11 Warranty INTRODUCTION Congratulations on your purchase of the HDMI Over RGB Your complete satisfaction is very important to us Gefen Gefen delivers innovative progressive computer and electronics add on solutions that harness integration extension distribution and conversion technologies Gefen s reliable plug and play products supplement cross platform computer systems professional audio video environments and HDTV systems of all sizes with hard working solutions that are easy to implement and simple to o2. feature DIP switch 2 on the sending unit must be in the ON position The DIP switch bank is located on the underside of the sender unit and is covered with a piece of a metallic colored tape 1 Locate the DIP switch bank on the sender unit 2 Using a small pointed tool change the position of DIP switch 2 to the ON position 3 View the output device to see if the issue is resolved SPECIFICATIONS HDMI 1 3 Features Supported Video Amp Bandwidth 340 MHz up to 16 bit YUV 444 1080p Digtal AUTO tine eS Dolby TrueHD amp DTS Master Protocols Pass Through CEC Lip Sync Video Resolutions 2K 1080P 1920x1200 Input Video Sidnal 1 0 ur a res 1 2V p p Input DDG Sigrial 5V p p Coaxial Conrnectors ine e Hiei teen 5 x BNC male IR back channel 4 2 5222 Seesen IR blaster HDMI Connector sse em Type A 19 Pin Female Power Supply 5 2 5V DC Power Consumption esses 10 Watts per unit max DIMENSIONS 2 2 a bene 4 25 W x 1 25 H x 3 9 D Shipping Weight aea ee es E Mee Aisle etd 3 Ibs HDCP Compliant 10 WARRANTY Gefen warrants the equipment it manufactures to be free from defects in material and workmanship If equipment fails because of such defects and Gefen is notified within two 2 years from the date of shipment Gefen will at its option repair or replace the e
3. warranty jsp PRODUCT REGISTRATION Please register your product online by visiting Gefen s web site at http www gefen com kvm Registry Registration jsp 11 Rev B1 MA HDMI 5 8 6 20600 Nordhoff St Chatsworth CA 91311 1 800 545 6900 818 772 9100 fax 818 772 9120 www gefen com supportGgefen com Qu c amp E O gt This product uses UL listed power supplies
4. data to the receiving unit The cable used for this connection cannot be omitted Clock BNC Connector This connector will transmit the CLOCK signal data to the receiving unit The cable used for this connection cannot be omitted Receiver Power BNC Connector This connector will transmit the power needed to operate the receiving unit The cable used for this connection can be omitted when using a 4 BNC type of cable setup If this cable is omitted power must separately be supplied to the receiver by one of the included 5V DC power adapters RECEIVER PANEL LAYOUT Front Panel Back Panel 10 RECEIVER PANEL DESCRIPTIONS Locking 5V DC Power Supply Input When using a 5 BNC cable system this connector will not need to be used When using a 4 BNC cable system a second 5V DC power supply part EXT PS52AU must be purchased and connected to this input port IR Receiver This receiver is used for the IR Repeater feature This receiver will accept standard IR remote commands for transmission back to the sending unit and then to the connected IR emitter blaster HDMI Output Port Connect the HDMI capable display device to this output port A secure connection to this HDMI port can be made using Gefen Mono LOK cables IR Extension Port An IR receiver extension sold separately part EXT RMT EXTIR can be connected to this port to relocate the IR receiver This option is available so that the receiving unit can b
5. e HDMI Over RGB Adjustments can be made to the HDMI Over RGB in the event that video fails to appear on the output device On each unit sender and receiver a bank of DIP Switches are present These DIP switches help boost functions in each unit The sender unit contains a boost for the 5V that is being sent over the BNC cable to power the receiver and the receiver contains a boost for Hot Plug Detection HPD These DIP switches may need to be enabled when the signal between both units are weak Use the instructions below to enable these functions When there is no video on the output device first try to boost HPD by enabling DIP switch 1 on the receiver unit The DIP switch bank is located on the underside of the receiver unit and is covered with a piece of a metallic colored tape 1 Locate the DIP switch bank on the receiver unit 2 Using a small pointed tool change the position of DIP switch 1 to the ON position 3 View the output device to see if the issue is resolved Operational power can be supplied by either an additional power supply or by using 5 BNC cables power is sent through the BNC port marked RP When the distance between the sending and receiving units are too great the operational power may be degraded enough to the point that the receiver unit will fail to operate The sender unit features a DIP switch that will apply a 5V boost and ensure that enough power is being sent to the receiver unit To enable this
6. e placed out of sight while still retaining the usability of the IR Repeating feature Link LED Indicator This LED indicator will become active once a valid link has been established between the sending and receiving units If this LED does not activate there is a possible mis connection between the two units Red BNC Connector This connector will transmit the RED signal data to the receiving unit The cable used for this connection cannot be omitted Green BNC Connector This connector will transmit the GREEN signal data to the receiving unit The cable used for this connection cannot be omitted Blue BNC Connector This connector will transmit the Blue signal data to the receiving unit The cable used for this connection cannot be omitted Clock BNC Connector This connector will transmit the CLOCK signal data to the receiving unit The cable used for this connection cannot be omitted Receiver Power BNC Connector This connector will transmit the power needed to operate the receiving unit The cable used for this connection can be omitted when using a 4 BNC type of cable setup If this cable is omitted power must separately be supplied to the receiver by one of the included 5V DC power adapters CONNECTING AND OPERATING THE HDMI OVER RGB How to Connect the HDMI Over RGB 1 Connect the HDMI source device to the HDMI Over RGB sender unit using the supplied HDMI cable 2 The HDMI Over RGB sender and receiver can be used with ei
7. ed XV Color Supported Dolby TrueHD amp DTS Master Supported e Protocol Pass Through Package Includes 1 HDMI Over RGB Sender 1 HDMI Over RGB Receiver 1 6 Foot HDMI Cable M M 1 5V DC Power Supply 1 User s Manual SENDER PANEL LAYOUT Front Panel Back Panel SENDER PANEL DESCRIPTIONS Locking 5V DC Power Supply Input Connect the included 5V DC power supply to this input port HDMI Input Port Connect the HDMI source device to this input port A secure connection to this HDMI port can be made using Gefen Mono LOK cables IR Out Port An IR emitter blaster sold separately part EXT 2IREMIT must be connected to this port to use the IR Repeater feature Connect the emitter to this output port and then connect the emitter eye on or near the IR receiver of the equipment that is intended for control Link LED Indicator This LED indicator will become active once a valid link has been established between the sending and receiving units If this LED does not activate there is a possible mis connection between the two units Red BNC Connector This connector will transmit the RED signal data to the receiving unit The cable used for this connection cannot be omitted Green BNC Connector This connector will transmit the GREEN signal data to the receiving unit The cable used for this connection cannot be omitted Blue BNC Connector This connector will transmit the Blue signal
8. perate The Gefen HDMI Over RGB The Gefen HDMI over RGB Extender is a handy extension solution which takes an HDMI signal and extends it far away over legacy 4 or 5 connector coaxial cabling The HDMI over RGB Extender employes Gennum s ActiveConnect technology and is capable of delivering 1080p HDMI at distances up to 330 feet 100 meters This is the ideal system for existing installations that are using RGBHV wiring and would like to step up to a digital signal but not rip into the walls to rewire the installation How It Works Simply connect one end of the supplied HDMI cable to your HDMI video source Connect the other end of the supplied HDMI cable to the input side of the HDMI over RGB Sender unit Connect the HDMI over RGB Sender to the sending end of your 4 or 5 plug coaxial cable run If you are using a 5 cable configuration power will be supplied to the receiving unit If you have a 4 cable configuration a second 5V power supply sold separately needs to be connected to the receiver unit At the receiving end of your coaxial cable extension plug your HDMI over RGB Receiver unit into your coaxial cable endpoints then plug the HDMI over RGB Receiver into your HDMI display You will now see HDMI audio video at the remote location with perfect clarity and sound You can connect and place an optional Gefen IR Emitter Blaster on the IR receiver of equipment you wish to control from the remote location Note This HDMI product s
9. quipment provided that the equipment has not been subjected to mechanical electrical or other abuse or modifications Equipment that fails under conditions other than those covered will be repaired at the current price of parts and labor in effect at the time of repair Such repairs are warranted for ninety 90 days from the day of reshipment to the Buyer This warranty is in lieu of all other warranties expressed or implied including without limitation any implied warranty or merchantability or fitness for any particular purpose all of which are expressly disclaimed 1 Proof of sale may be required in order to claim warranty 2 Customers outside the US are responsible for shipping charges to and from Gefen 3 Copper cables are limited to a 30 day warranty and cables must be in their original condition The information in this manual has been carefully checked and is believed to be accurate However Gefen assumes no responsibility for any inaccuracies that may be contained in this manual In no event will Gefen be liable for direct indirect special incidental or consequential damages resulting from any defect or omission in this manual even if advised of the possibility of such damages The technical information contained herein regarding the features and specifications is subject to change without notice For the latest warranty coverage information please visit Gefen s Warranty web page at http www gefen com kvm aboutus
10. ther a user supplied 4 or 5 BNC cable system 5 BNC Cables Connect all 5 BNC cables to the R G B C and RP BNC connectors between the HDMI Over RGB sender and receiver units 4 BNC Cables Connect the 4 BNC cables to the R G B and C BNC connectors between the HDMI Over RGB sender and receiver units The RP BNC connector will not be used and a second power supply part EXT PS52AU will need to be purchased and connected to the receiver unit 3 Connect the HDMI capable display device to the HDMI Over RGB receiver unit using a user supplied HDMI cable 4 Connect the included 5V DC power adapter to the HDMI Over RGB sender unit NOTE If using a 4 BNC cable system a second power supply must be purchased and connected to the HDMI Over RGB receiver unit 5 Poweron the display first and then the source How to Operate the HDMI Over RGB The HDMI Over RGB does not require any configuration for standard operation IR Repeater Feature An IR emitter blaster sold separately part EXT 2IREMIT is required to send relayed IR commands to equipment at the sender s location Connect the IR emitter jack to the HDMI Over RGB sender unit and connect the IR eye on or near the IR receiver of the equipment that is intended for control Point the equipment s IR remote at the IR receiver on the HDMI Over RGB receiver unit and press buttons to relay commands back to the equipment device TROUBLESHOOTING THE HDMI OVER RGB Troubleshooting th
11. upports BOTH Audio and Video signals OPERATION NOTES READ THESE NOTES BEFORE INSTALLING OR OPERATING THE HDMI OVER RGB The HDMI Over RGB is designed for either 4 or 5 BNC cable type setups When 5 BNC cables are present and used a power supply on the HDMI Over RGB Receiver will not need to be used Power will be transmitted over the cables When a 4 BNC cable setup is used a second power supply part EXT PS52AU for the receiving unit will need to be purchased and connected HDMI 1 3 compliant Please see page 3 for a listing of supported HDMI 1 3 features HDCP compliant The HDMI Over RGB has an IR repeater feature that will send standard IR remote control commands from the receiver back to the sender This is useful for controlling equipment from a remote location IR commands cannot be relyed from the sender to the receiver Please see page 8 for more details Resolutions of up to 1080p Full HD are supported for HDTV use Resolutions of up to 1920 x 1200 are supported for computer use The HDMI Over RGB was designed for use with 75O coaxial cable FEATURES Features e Connects HDMI sources to remote HDMI displays over legacy RGBHV cabling Supports extension distances of up to 330 feet Supports resolutions up to 1080p 2K and 1920 x 1200 HDMI and HDCP compliant e Extends any IR device HDMI 1 3 Features e Lip Sync Pass Through e 340 MHz up to 16 bit YUV 444 supported 1080p Deep Color Support
Download Pdf Manuals
Related Search