KH406 MAXI LIFT
Contents
1. Manufact urea of amp Mursing Home Equipment KH406 7 MAXI LIFT2. 2 4 The hoist can lie on its side without damage to the plastic cover but care must be taken when lowering raising You now have access to all the lubrication points ie pivot points leg lever and leg pivot Simply spray TAC 2 on all the pivot points for 2 seconds Leg Actuator Pivots Fig 7 Leg Pivots Fig 7 Tie Rod Pivot Points Fig 7 Fig 7 ARM AND ACTUATOR PIVOT POINTS The arm pivot points will need to be lubricated with TAC 2 or similar lubricant Simply spray for 2 seconds on each side of the recommended points monthly 3 1 Arm Pivot Fig 8 Actuator Pivots Fig 8 Fig 8 KH406 6 MAXI LIFT NOTE TAC 2 is a CRC product and is available from most automotive outlets or from Kerry Equipment GENERAL CLEANING 1 The KH 406 MAXI LIFT can be cleaned with a low strength detergent warm water and a soft textured cloth This includes All stainless steel Epoxy powder coated framework 2 SLING CARE Protect from direct sunlight Repair any cuts or fraying immediately Slings are machine washable 3 CAUTION Do not immerse any parts in water Do not allow water cleaning liquid to enter the battery or controller Clean up spills immediately Equipment Aust Pty Ltd r ABN 71 082 784 147 i v 4 Halley Road Balcatta Perth Equipment Australia 8021 Telephone 61 8 9240 2244 t Facsimile 61 89240 1488 A C Hills Company emailikernyedquiprernt com au vi Kerry equipment corr au
3. CARE AND CHARGING 4 1 CHARGING Before the KH 405 F can be operated the battery pack will need to be charged Please follow the instructions below 4 2 Plug the charger unit Fig 4 into the 240 Volt supply outlet The unit is now ready to accept a battery that requires charging a GREEN L E D ON will be displayed 4 3 charge the battery simply locate the battery on the mount bracket and clip into position The GREEN and ORANGE L E D on the front of the charger will be displayed The battery is fully charged when the ORANGE L E D is OFF and only the GREEN L E D is displayed 4 4 battery system is going to be used replace the first battery once charged with the second battery Charge using the same procedure as above NOTE A battery pack may remain on charge indefinitely without any detrimental effects to the battery or charging unit Fig 4 Charger unit shown without battery attached KH406 4 MAXI LIFT BATTERY CARE The KH 406 uses fully sealed lead acid batteries They are designed to be recharged on a regular basis To care for your batteries and obtain the maximum life DO NOT allow the batteries to run totally flat before recharging The controller is fitted with an audio low battery warning alarm When this warning alarm sounds complete the lift process then change the battery and recharge Kerry Equipment recommends that a 2 battery system be used this allows one battery to always be on charge whil
4. KH406 MAXI LIFT SHOWN WITH OPTIONAL WEIGHT SCALE OPERATING MAINTENANCE amp CLEANING MANUAL Kerry TM A Fills Company n 89726 KEIM 045 INDEX PAGE SPECIFICATIONS 2 SAFETY PRECAUTIONS 3 OPERATING INSTRUCTIONS 3 MAINTENANCE INSTRUCTIONS 5 CLEANING INSTRUCTIONS 7 SPECIFICATIONS DIMENSIONS Length 1445mm Wiath 0mm Height 1460mm Effective lift range 600mm 1880mm Leg gating inside 590mm 1090mm Lift reach 1140mm Under base clearance 60mm Base height 220mm Leg height from floor 130mm Turning radius 1340mm LIFT SPEED Slow 30mm per second LIFT DRY WEIGHT 70 Kg with battery LIFT CAPACITY Max load 300kg CASTORS 2150 Total lock rear polyurethane castor 275 Swivel front polyurethane castor Note Smaller castors available on request FINISH Epoxy powder coated Polyurethane legs and yoke PVC cover ELECTRICAL ITEMS Tested by Linak Australia to standards AS 3108 1990 and AS 3200 1 1990 KH406 2 MAXI LIFT SAFETY PRECAUTIONS 1 Always use the correct slings on the hoist 2 MAXIMUM safe working load is 300 Kg 3 EMERGENCY STOP This is the big RED switch located on the front of the controller If there is a need to use this simply depress the switch and it will automatically lock the position and cut all power to the electrical system To disengage the emergency stop switch after it has been depressed turn the switch in a clockwise direction and the switch sho
5. e the other is in use hence the hoist may never be out of service with a flat battery MAINTENANCE INSTRUCTIONS LUBRICATION The KH 406 MAXI LIFT requires periodical lubrication These points are 1 CASTORS It is always best practice to remove all hair and lint from the castors as soon as possible always allowing free movement of all the wheels The castors need to be lubricated monthly Use TAC 2 only This involves 1 1 The Castor head bearing will need lubricating Simply spray TAC 2 up into the bearing while rotating the castor Fig 5 1 2 The wheel also requires lubricating every couple of months To do this the wheel must be unbolted and removed from the castor frame TAC 2 can then be sprayed into the hub centre to lubricate the internal bearings Fig 6 Fig 5 Fig 6 BASE PIVOT POINTS All pivot points will need to be lubricated with TAC 2 or similar lubricant Simply spray for 2 seconds on each side of the recommended points monthly The hoist has to be turned onto its side for access to the following lubrication points To do this 2 people are required Follow the instruction below 2 1 Both people are to stand on one side of the hoist One near the push handle the other by the side of the hoist 2 2 person near the push handle locks the total lock castors KH406 5 MAXI LIFT 2 3 n conjunction with one another pull the hoist towards the side lowering the hoist onto its side on the floor
6. uld return to its original position 5 EMERGENCY LOWERING RAISING The emergency lowering raising buttons can be used to lower raise the hoist if there is a electrical or handset failure The switches are located on the controller under the big red emergency stop switch Simply press using a ball point pen or similar object 6 For safety precautions only properly trained personal should use the hoist OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS 1 INSTALLATION OF BATTERY PACK Before the MAXI LIFT can be operated the battery pack will need to be placed on charge See 2 1 2 For Charging Battery When the battery pack is fully charged remove the battery from the charger and place on the hoist Simply locate the battery on the mounting bracket and clip the release lever into the secure position The Maxi Lift is now ready for use Fig 1 Fig 2 2 HANDSET 2 1 RAISE LOWER The MAXI LIFT operates via a touch pad handset The top two switches on the handset are for raising and lowering To raise or lower the hoist simply press the required switch on the pad Fig 4 KH406 3 MAXI LIFT 2 2 LEG GATING To OPEN or CLOSE the Gate on the legs simply press the lower two switches on the handset Fig 2 shows the lower sets of switches are for the leg gate Open on the left close on the right 3 YOKE SLING MOUNTING POINT Fig 3 Refer to the fitting instructions supplied with your chosen sling Fig 3 4 BATTERY
Download Pdf Manuals
Related Search