Installation Manual - Security Camera King
Contents
1. Please contact your local retailer if there is internal setup or maintenance requirement Weare not liable for any problems caused by unauthorized modifications or attempted repair Do not allow other object falling into the device Please make sure there is no metal or inflammable explosive substance in the speed dome The above mentioned objects in the device may result in fire short circuit or damage Please shut down the device and disconnect the power cable if there is water or liquid falling into the camera Please contact your local retailer ASAP Please pay attention to the camera Avoid the sea water or rain to erode the camera Handle carefully Do not allow this series product fall down to the ground Avoid heavy vibration Installation Environment Requirement This series speed dome should be installed in a cool dry place away from direct sunlight inflammable explosive substances and etc This series product shall be away from the strong electromagnetism radiant please keep it away from wireless power TV transmitter transformer and etc Daily Maintenance Please use the soft cloth to clean dust on the shell or you can use soft cloth with cleaning liquid to clean the shell and then use soft cloth to make it dry Do not use gasoline dope thinner or other chemical material to clean the shell It may result in shell transfiguration or paint flake Do not allow the plastic or ru2. complete firmly Figure 1 7 e After installation use hex wrench to fix the M6 stainless screws 3 in total for the last time to make sure these three M6 stainless screws have been completely fixed so that the intelligent dome could be completely installed to the bracket Important If it is not firm enough the dome may have a potential risk to fall down Stepb Fix the dome a Choose the wall to install the wall shall be thick enough to install expansion bolt b The wall shall be capable of bearing 8 times of the weight of accessories c Please refer to chapter 3 for detailed installation Step6 Wire connection Connect the multi functional composite cable to the corresponding power cable video output cable RS485 control cable alarm I O terminal then paste the insulating tape in the connection position to be waterproof Note The video port is covered the heat shrink tube of high shrinking ratio After the video connection please heat the tube to make sure the video port is damp proof and water proof Step7 Now the installation is completed Important After the installation please make sure The three stainless screws of the quick installation port are firmly secure The quick installation speed dome is fixed The speed dome is straight The steel wire connection is firm After your installation the interface is shown as below Figure 1 8 1 3 Initial Setup The default setup is Address 1 B
3. Please refer to user s manual for detailed information Please keep all package material well for future use Please keep speed dome package material well in case you need to send it back to your local retailer or manufacturer for maintenance work Non original package material may result in device damage during the transportation Check Accessories Before the installation please check the accessories one by one according to the packing list Please make sure all the components listed are includes Important The speed dome power is AC 24V 1 2 Installation Please note the speed dome includes the intelligent high speed dome IP intelligent speed dome and etc The speed dome has several types of installation brackets You can refer to the chapter 3 for detailed information Step1 Open the transparent cover and take out the packing material EPE around the speed dome driver Please remove the protective paster from the driver and take off the camera lens cap See Figure 1 1 Protective paster Figure 1 1 Step2 Set address and Baud Rate Now you can set the intelligent speed dome address and baud rate The speed dome interface is shown as below See Figure 1 2 There are two dial switches SW2 and SW3 Here you can set the address baud rate and etc Please refer to chapter 1 4 for detailed information Figure 1 2 Step3 Install the transparent cover You need to check the steel wire of the bracket is fir
4. See Figure 5 4 Figure 5 4 17 Please refer to chapter 1 2 for detailed installation information 18 6 APPENDIX I THUNDER PROOF AND SURGE PROTECTION This series speed dome adopts TVS lighting protection technology It can effectively prevent damages from various pulse signals below 1500W such as sudden lighting and surge While maintaining your local electrical safety code you still need to take necessary precaution measures when installing the speed dome in the outdoor environment The distance between the signal transmission cable and high voltage device or high voltage cable shall be at least 50 meters Outdoor cable layout shall go under the penthouse if possible For vast land please use sealing steel tube under the land to implement cable layout and connects one point to the earth Open floor cable layout is forbidden In area of strong thunderstorm hit or near high sensitive voltage such as near high voltage transformer substation you need to install additional high power thunder protection device or lightning rod The thunder protection and earth of the outdoor device and cable shall be considered in the building whole thunder protection and conform to your local national or industry standard System shall adopt equal potential wiring The earth device shall meet anti jamming and at the same time conforms to your local electrical safety code The earth device
5. Integrated Intelligent Speed Dome Installation Manual Version 1 0 Table of Contents 1 INTELLIGENT SPEED DOME INSTALLATION eene 1 1 1 Installation PreparatiOn eee eeee eere eere eere eere eere eere etna sense ense tn se ense ense ense esseesseeseeesseese L 1 2 E CH e T HU 1 3 Mitia SetU EE eise aasia 1 4 BIENES e ET RR M A 1 4 1 Communication protocol and Baud rate se seseeseseeseseseesesetseseeststsststsresestrsesteststesesessesesrrses 7 1 4 2 Address Setup nen E E E RR REG NR EHE E 8 2 BRACKET DIMENSIONS Qu sek KEEN KKK REENEN RENE KEREN EEN RENE KEREN KEREN 10 2 1 Wall Mount bracket e ett eer eee eno tei onse vo endo S Eee env deeso vo snoer to se sapevo dreisoni LO 2 2 Corner mount bracket oeste eot es tea ov cde ev ee ley yere eee y eege eege tastas iei eei LO 2 3 Pole mount bracket 15 reet rano e aoro ao eu pn nae e onn asta po aao inesse sse sus co on eet eedde eer eec zngec LAL 3 WALL MOUNT BRACKET INSTALLATION cc eeeeee nennen 12 3 1 Component InstallatiOn eee eeee esee eee eese eee eese ss senses sen seen ssesseesseesseeseeesseesseeseesse LD 3 2 DVS TAN ATOM P A ROLLE D 3 2 1 Installation Requirements nennen nnne ennt nne 12 3 2 2 Installation O ET S T E r A nente nnne terne nnne nnne nne 12 4 COR
6. NER MOUNT BRACKET INSTALLATION re 14 4 1 Component InstallatiOn oro ora oer aranea aranea aera ara ara nera aera nera ara aea aea aaa nane n anon 14 4 2 EA CITE de a E ES EE LA 4 2 1 Installation Requirements eene 14 4 2 2 Installation Steps sssssssssssssssssseseeseeeeene eene nnne nennt nennt enne 14 5 POLE MOUNT BRACKET INSTALLATION ener 16 5 1 iactu me LO Installation Requirements nennen nnne enne eerte nnne tnnt 16 ii 6 7 7 1 7 2 7 3 7 4 APPENDIX THUNDER PROOF AND SURGE PROTECTION 19 APPENDIX Il ABOUT RS485 BUS eese 20 R9485 Bus Main Feature 5 n etes e ete E E ee ere let avoue ere oo ee esee ege 20 RS485 Bus Transmission Distance cccccsscccsssesccesscseccsscscccessescccessccesessescesessesessssessees A The Problem in Practical Uee e dergege eeben gege sen eror sau ses soie nos ere eos ua reed o etes vius reves eser ee gg Zoe 20 iii Welcome Thank you for purchasing our speed dome Please read the following safeguards and warnings carefully before you install or use the product lv Important Safeguards and Warnings Safety Measures Qualified Engineer Needed The installation engineer or maintenance engineer shall have corresponding CCTV system installation certificate or mai
7. T INSTALLATION Pole mount bracket and its components are shown as below See Figure 5 1 Wall Bracket Figure 5 1 5 1 Installation Installation Requirements The corner mount speed dome can be installed in the hard construction wall in the indoor or outdoor environments Before the installation please make sure the pole bracket can sustain the 8X weight of the speed dome The diameter of the pole structure shall comply with the installation dimension of the clamp Default factory clamp is six inches for the column of 130 152mm It can work with the pole installation bracket You can adjust the diameter and the value clamp specification is p59 82mm q84 108mm q103 127mm q130 152mm q155 178mm q180 203mm q194 216mm The clamp is shown as in Figure 5 2 16 Figure 5 2 For special dimensions please contact us for more information Please refer to Figure 5 3 to install clamp and pole bracket Pull the cable out of the pole accessories and then use clamp to fix the pole accessories to the pole Finally you can use glass cement to the output hole to secure waterproof Clamp and pole bracket connection Pole bracket and the pole connection Figure 5 3 After you installed bracket and external cover loosen the captive screws and open the panel pull the power cable through the hanging bracket and then fix the hanging bracket to the wall Please pay attention to the waterproof between the bracket and the wall
8. aud rate 9600 Parity NONE e 1200 Matching resistor OFF 1 4 Dial Switch Setup Please set address baud rate and parity before controlling the dome The two dial switches of the speed dome are SW2 and SW3 These are to specify the speed dome parameter such as baud rate address parity and etc When the button is ON it is 1 In SW2 1 is the lowest bit and the 8 is the highest bit In SW3 1 is the lowest bit and the 4 is the highest See Figure 1 9 Figure 1 9 1 4 4 Communication protocol and Baud rate Figure 1 10 SW3 is used for baud rate setup and parity Baud rate Parity 1 2 3 4 Baud rate settings Please refer to the sheet below for detailed information 1 2 Baud rate ON ON 1200bps Parity settings Please refer to the sheet below for detailed information 3 4 Parity OFF OFF NONE ON OFF EVEN OFF ON ODD ON ON NONE 1 4 2 Address Setup The speed dome address setup interface is shown as below See Figure 1 11 1 2 3 4 5 6 7 8 Figure 1 11 SW2 is used for address setup The dome use dial switch to set address and
9. bber material to touch the shell for a long time It may result in paint flake vi 1 INTELLIGENT SPEED DOME INSTALLATION 1 1 Installation Preparation Basic Requirement e Allinstallation and operation here should conform to your local electrical safety codes Before installation please open the package and check all the components are included Please make sure the speed dome installation environment and installation mode can meet your requirement If there is special requirement please contact your local retailer for more information We assume no liability or responsibility for all the fires or electrical shock caused by improper handling or installation Check installation space and installation location intension Please make sure the installation environment has enough space to install the speed dome and its corresponding bracket Please make sure the ceiling wall and the bracket can support the speed dome and its corresponding installation component The safety factor shall be 8X About cable Please select the cable according to your transmission distance The minimum video coaxial cable requirement is e 75ohm Full cable with copper conductor 95 knitted copper shield International Model Max Distance Ft M RG59 U 750ft 229m RG6 U 1 000ft 305m RG11 U 1 500ft 457m Set dial switch button Set dial switch button according to control protocol and speed dome address
10. ected to Figure 1 14 2 BRACKET DIMENSIONS 2 1 Wall mount bracket The wall mount bracket dimensions are shown as below See Figure 2 1 p AD E XE 145 5 6 Uniform Figure 2 1 2 2 Corner mount bracket The corner mount bracket is shown as below See Figure 2 2 10 170 1 Figure 2 2 2 3 Pole mount bracket The corner mount bracket is shown as below See Figure 2 3 8 5 H 4 M8 e A0 9 oF 027 S S ss8 L L 64 AR E 1 ss 130 O ei Figure 2 3 11 3 WALL MOUNT BRACKET INSTALLATION 3 1 Component Installation Wall mount bracket is shown as below See Figure 3 1 Wall Bracket M6 Hexagon stainless screws Figure 3 1 3 2 Installation 3 2 4 Installation Requirements The wall mount speed dome can be installed in the hard construction wall in the indoor or outdoor environments Before the installation please make sure The wall is thick enough to install the expansion bolt The wall can at least bear the 8x weight of the speed dome 3 2 2 Installation Steps Please draw four holes position in the wall according to the hole of the bottom of the wall mount bracket Then you can dig four holes and insert the expansion bolts not provided Use four hex bolts and flat washer to fix the bracke
11. mly secure or not a b Please line up the captive screws to the quadrate groove of the bracket and then push the bracket into the internal enclosure Fix these two captive screws See Figure 1 3 Captive screw Bracket steel wire Quadrate groove of the bracket Bracket e sealing ring Captive screw Captive screw Figure 1 3 Step4 the installation steps of using wall mount bracket a Take the composite cable through the bracket b Lineup the straight edge of the internal enclosure of the intelligent speed dome to the straight edge of the wall mount bracket and then push the speed dome to the bottom of the bracket slowly The straight edge of wall mount bracket ght edge of internal enclosure of igent speed dome Mutiple function composite cable The strai the intel Figure 1 4 Turn the M6 16 hexagon stainless screw on the bracket to the 6 5 hole of the straight edge of the internal enclosure of the intelligent speed dome Use the Hex Wrench to fix these stainless screws firmly Important If it is not firm enough the dome may have a potential risk to fall down See the two figures below M6 16 hexagon stainless screw Cushion Multiple function composite cable 6 5 hole of the internal enclosure Figure 1 5 The M6 16 hexagon stainless screw must be screwed into the 06 5 hole very firmly Figure 1 6 d Usethe hex wrench to turn another two M6 10 hexagon stainless screws and cushions
12. ntenance qualification certificate The installation engineer or maintenance engineer shall have qualification certificate for work at height The installation engineer or maintenance engineer shall have the basic knowledge and operation technique for low voltage cable layout and low voltage electronic cable connection Please read the installation manual carefully and keep it well for future reference We are not liable for any problems caused by unauthorized modifications or attempted repair Lifting Appliance Requirement Please select the proper speed dome installation mode and use the lifting appliances at the safety environment e The lifting appliances shall have the enough capacity to reach the installation height The lifting appliances shall have safe performance Precautions Safety Transportation Heavy stress violent vibration or water splash are not allowed during transportation storage and installation This series product must use split type package during the transportation Weare not liable for any damage or problem resulting from the integrated package during the transportation When device is malfunction Shut down the device and disconnect the power cable immediately if there is smoke abnormal smell or abnormal function Please contact your local retailer ASAP Do not try to dismantle or modify the device There is risk of personal injury or device damage resulting from opening the shell
13. s is off Addterminal matching resistance smooth The distance between host and e Add RS485 distributor speed dome is too far Parallel connected too much speed domes Note e This manual is for reference only Slight difference may be found in the user interface e All the designs and software here are subject to change without prior written notice e If there is any uncertainty or controversy please refer to the final explanation of us e Please visit our website or contact your local service engineer for more information 21
14. shall not short circuit to N neutral line of high voltage power grid or mixed with other wires When connect the system to the earth alone the earth resistance shall not be more than 4O and earth cable cross sectional area shall below 25 mm2 See Figure 6 1 Video Lighting Rod Communication _ Lighting Rod Power Seq Lighting Rod The speed dome shall be installed within the 45 angel of the lighting rod Earth cable resistance shall be less than 49 Steel tube shield Figure 6 1 19 7 APPENDIX II ABOUT RS485 BUS 7 1 RS485 Bus Main Feature RS485 is semi duplex communication cable of impedance 1200 Its max load amount is 32 effective loads including main control device and devices to be charged 7 2 RS485 Bus Transmission Distance When we take 0 56mm 24AWG twisted pair as communication cable the max transmission distance theoretically are listed below according to different baud rates Baud Rate Max Distance 2400 BPS 1800M 4800 BPS 1200M 9600 BPS 800M In the following situations the max transmission distance shall become shorter accordingly The communication cable is a little bit thin The surrounding environment has strong electromagnetic interference There are too much devices connected to the RS485 bus And vice versa the max transmission distance shall become longer 7 3 The Problem in Practical Use In practical
15. t in the expansion bolts Figure 3 2 12 Finish the installation See Figure 3 3 Figure 3 3 Please refer to chapter 1 2 for detailed installation information 13 4 CORNER MOUNT BRACKET INSTALLATION 4 1 Component Installation Corner mount bracket and its components are shown as below See Figure 4 1 Wall Bracket MG Hexagon stainless screws Figure 4 1 4 2 Installation 4 2 4 Installation Requirements The corner mount speed dome can be installed in the hard construction wall in the indoor or outdoor environments where there is a 90 degrees angle Before the installation please make sure The wall is thick enough to install the expansion bolt The wall can at least bear the 8x weight of the speed dome 4 2 2 Installation Steps 14 Please draw four holes position in the wall according to the holes of the corner installation accessories See Figure 4 2 Installation hole Figure 4 2 Then you can dig four holes and insert the M8 expansion bolts Pull the power cable video control cable and the alarm cable through the centre hole of the bottom of the corner bracket the waterproof adhesive and the centre of the bracket Please reserve the enough cable connection length and then use the M8 expansion bolt to secure the corer mount bracket chassis on the wall See Figure 4 3 Figure 4 3 Please refer to chapter 1 2 for detailed installation information 15 5 POLE MOUNT BRACKE
16. the encode mode adopts binary system 1 to 8 is valid bit The highest address bit is 255 You can refer to the following sheet for more information Address 1 2 3 4 5 6 7 8 1 OFF OFF OFF OFF OFF OFF OFF OFF 1 ON OFF OFF OFF OFF OFF OFF OFF 2 OFF ON OFF OFF OFF OFF OFF OFF 3 ON ON OFF OFF OFF OFF OFF OFF 4 OFF OFF ON OFF OFF OFF OFF OFF 5 ON OFF ON OFF OFF OFF OFF OFF 6 OFF ON ON OFF OFF OFF OFF OFF 7 ON ON ON OFF OFF OFF OFF OFF 8 OFF OFF OFF ON OFF OFF OFF OFF 254 OFF ON ON ON ON ON ON ON 255 ON ON ON ON ON ON ON ON 1 4 3 Terminal matching resistor settings Terminal matching resistor is on power supply board and there are two ways to connect Please see the figure below for reference J6 1 2 2 3 1200 ON OFF Figure 1 12 The following figure shows the factory default mode You can see the jumper cap connection board is inserted into the socket NO 2 and NO 3 1200 resistance has not been connected to then Default jump settings 1200 resistance has not been connected to Figure 1 13 Pull the jumper cap off the socket NO 2 and NO 3 and then insert into socket NO 1 NO 2 if 1200 resistance is needed to be connected to the electric circuit See the figure below for reference Jump settings 1200 resistance has been conn
17. usage we usually adopt star type connection The terminal resistance shall connect to the furthest two devices Such as device 1 and device 15 in Figure 7 1 But this connection way does not conform to RS485 Bus standard When the distances between devices are too long the signal reflection occurs and anti jamming decreases thus the signal reliability becomes very low You can see speed dome is not under control or speed dome is running automatically and can not stop MUN E eN P di fg TS AS gs ud Main Control Device Figure 7 1 In this situation we recommend RS485 distributor This device can turn star type connection into the connection that conforms to RS485 bus industry standard which can avoid the above mentioned problems and enhance communication reliability See Figure 7 2 20 Figure 7 2 7 4 RS485 Bus FAQ Phenomenon Possible Reasons Solution Speed dome Host address baud rate and e Modify host or speed dome setup can run self speed dome address baud rate Switch RS485 positive end and diagnosis but I are not match negative end can not control Positive and negative end of e Fix connection cable firmly it RS485 Bus are misconnected Replace RS485 Bus e Connection cable is loose e RS485 Bus connection are cut off can control e RS485 Bus connection are not Connect RS 485 Bus again the speed good Replace RS485 Bus dome but is not e One RS485 bu
Download Pdf Manuals
Related Search