User manual ............... 2 ............... 25 Washing machine ZWH7120 P
Contents
1. Follow the product manufacturers instructions on quantities to use Not enough washing powder causes e the washload to tum grey e greasy clothes Too much washing powder causes e sudsing e reduced agitation and washing effect inadequate rinsing Use less detergent if e you are washing a small load the laundry is lightly soiled e large amounts of foam form during washing Open the detergent dispenser drawer The detergent dispenser is divided into three compartments e Compartment LL this compartment is only used for washing powder when a program has Prewash or Stain 10 e Compartment LLU this compartment is used for washing powder or liquid e Compartment amp for fabric conditione his compartment is used and starching agent Aways add laundry detergents before switching the machine on and keep the dispenser clean and dry so that the detergent can be efficiently dispensed from the unit Measure out the detergent and the fabric softener Measure out the amount of detergent required pour it into the main wash compartment LL for prewash LLY for mainwash If you wish to carry out the prewash phase pour it into the compartment marked LU If required pour fabric softener into the compartment marked the amount used must not exceed the MAX mark in the drawer 8 for softener Close the drawer gently2. Control panel L O OO Door Lock F Delay Start Specials x Cotto Li Jeans on Cottons V ns Mini 30 a Prewash 09 1200 a O 60 Blanket n y Ow O Easy Iron Syntheti O 30 EEN i ra O Cold O70 o o sa gt o MissdlFabrie Temp Spin Rinse Hold Super Quick Extra Rinse Start Pause Drain Ra Delicates inse Handwash Rinse Handwash N lo Pra Program selector dial Temperature button Spin button Rinse Hold button Super Quick button BONGO Extra Rinse Button Display Start Pause button Delay Start button 11 Set your washing program 12 Program selector dial specials SY Cottons p Jeans 9 Cottons Y Mini 30 gt Prewash Blanket l d Economy Easy m j Synthetics Spin o Mixed Fabric ee Dar Delicates Handwash Rinse Handwash Temperature selector 90 O 60 40 30 O Cold Temp O Tum the program selector dial to the required program The green Start Pause light starts to flash The selector dial is divided into following sections e O Carcelling Off e Rinse e Cottons tg Drain L Cottons Prewash Spin oe Cottons Economy e A Easy Iron e amp Synthetics i Blanket Mixed Fabric FES Mini 80 CG ER Delicates Jeans WoolHandwash The selector dial can be turned either clockwise or anticlockwise Position Off to Reset
3. Woollens and hand Main wash at washing fabrics Cold 40 C Rinses Long spin Separate rinse cycle for Rinses hand washed items of Long spin cottons Spin Reduction Rinse Hold Delay Start Super Quick Extra Rinse Spin Reduction Rinse Hold Delay Start Super Quick Extra Rinse Spin Reduction Rinse Hold Delay Start Extra Rinse Spin Reduction Rinse Hold Delay Start Super Quick Extra Rinse Spin Reduction Rinse Hold Delay Start Extra Rinse Spin Reduction Maximum 700 rpm Rinse Hold Delay Start Super Quick Extra Rinse Spin Reduction Rinse Hold Delay Start Spin Reduction Rinse Hold Delay Start Extra Rinse ca 7 0 kg 7 0 kg 2 5 kg 25 kg 26 kg 2 0 kg 7 0 kg Program Type of laundry Description LEVA Temperature of program Load For emptying out the Drain of Not available Drain water left in the drum water fe Separate spin program Drain Spin Reduction 7 0 Spin for spin out the water Long spin Delay Start kg from clothes Main wash at Spin Reduction 25 Easy Iron Cottons and synthetic Cold 40 C Maximum 900 rpm kg Cold 40 G oF mixed fabrics Rinses Rinse Hold Short spin Delay Start Extra Rinse ch A gentle program Main wash at Spin Reduction 7 0 Blanket designedfor mixed 30 40 C Maximum 700 rpm kg W 30 40 C fabrics found in delicate Rinses D
4. as paint ink rust and grass before washing Underwired bras must NOT be machine washed Garments which have been in contact with volatile petroleum products should not be machine washed If volatile cleaning fluids are used care should be taken to ensure hat the fluid is removed from the garment before placing in the machine lever pull the power supply cable to remove he plug from the socket always take hold of he plug itself lever use the washing machine if the power supply cable the control panel the working surface or the base are damaged so that the inside of the washing machine is accessible Child safety This washing machine is not intended for use by young children or infirm persons without supervision Young children should be supervised to ensure that they do not play with the appliance The packaging components e g plastic film polystyrene can be dangerous to children danger of suffocation Keep them out of children s reach Keep all detergents in a safe place out of children s reach Make sure that children or pets do not climb into the drum To avoid this the machine incorporates special feature To activate this device rotate the button without pressing it inside the door clockwise until the groove is horizontal If necessary use a coin To disable this device and restore the possibility of closing the door rotate the button anti clockwis
5. in the following cases e when selecting a wash program e when depressing the options buttons e atthe end of the cycle e inthe event of operating problems By pressing the Rinse Hold and Super Quick buttons simultaneously for about 8 seconds the acoustic signal is deactivated except for the events of operating problems By pressing these 2 buttons again the acoustic signal is reactivated 15 Altering an option or a running program Opening the door after the program Itis possible to change any option before the has started program carries it out The option Super Quick cannot be modified after the Start Pause has been pressed If you need to open the door you must first set the washing machine to PAUSE by pressing the Start Pause button after that Changing a running program is possible only you need to wait about 2 3 minutes to by resetting it Tum the program selector dial release door lock to Off and then to the new program position The washing water in the tub not be emptied out Start the new program by depressing the Start Pause button again the machine is already heating or the water vel is above the bottom edge of the door or hat the drum is turning In this case the door can not be opened Interrupting a program you can not open the door but you need to Depress the Start Pause button to interrupta Open it you have to switch the ma
6. pilot light flashes to indicate that n eliminated press the Start Pause button to restart the program If m persists contact your local Service Centre Maitunction __ Possible cause solution The washing machine does not start The machine does not fill The machine fills then empties immediately The machine does not empty and or does not spin 22 The door has not been closed Red Start Pause pilot light flashes The plug is not properly inserted in the power socket There is no power at the socket The selector dial is not correctly positioned and the Start Pause button has not been depressed The delay start has been selected The water tap is closed Red Start Pause pilot light flashes The inlet hose is squashed or kinked Red Start Pause pilot light flashes Close firmly the door nsert the plug into the power socket Please check your domestic electrical installation Please turn the selector dial and oress the Start Pause button again f the laundry are to be washed immediately cancel the delay start Open the water tap Check the inlet hose connection The filter in the inlet hose is blocked Red Start Pause pilot light flashes The door is not properly closed Red Start Pause pilot light flashes he end of the drain hose is too low The drain hose is squashed or kinked Clean the water inlet hose filter Close firmly the door Refer to
7. program Switching OFF the machine At the end of the program the selector dial must be turned to position Off to switch the machine off Attention If you tum the program selector dial to another program when the machine is working the red Start Pause pilot light will flash 8 times to indicate a wrong selection The machine will not perform the new selected program Cancelling a program Tum the selector dial to Off to cancel a program which is running Now you can select a new program Press this button repeatedly to increase or decrease th temperature if you want your laundry to be washed at a temperature different from the one proposed by the washing machine If a temperature is chosen that is not allowed with the selected program the red pilot light of the Start pause button will flash 3 times Spin Buttons 1200 O 900 O 700 Spin Rinse Hold O Rinse Hold Super Quick Buttons O Super Quick O Extra Rinse Option O Extra Rinse Display Press the Spin button repeatedly to change the spin speed if you want your laundry to be spun at a speed different from the one proposed by the washing machine The relevant light will light up By selecting this option the water of the last rinse is not emptied out to prevent the fabrics from creasing To empty out the water e tum the program selector dial to Off e select the Drain or Spin progra
8. 240 V single phase 50 Hz supply An incorrect power supply may void your warranty Check that your domestic electrical installation can take the maximum load required 2 0 kW also taking into account any other appliances A Important Connect the machine to an earthed socket The manufacturer declines any responsibility for damage or injury through failure to comply with the above safety precaution Should the appliance power supply cable need to be replaced this should be carried out by our Service Centre in use First Use e Run a cotton cycle at 90 C without any laundry in the machine to remove any manufacturing residue from the drum and tub Pour 1 2 a measure of detergent into the dispenser drawer and start the machine Daily Use i Sorting the laundry Follow the wash code symbols on each garment label and the manufacturer s washing instructions Sort the laundry as follows whites coloureds synthetics delicates woollens Before loading the laundry e Never wash whites and coloureds together Whites may lose their whiteness in the wash e New coloured items may run in the first wash they should therefore be washed separately the first time e Make sure that no metal objects are left in the laundry e g coins hair clips safety pins pins e Remove persistent stains before washing e Button up pillowcases close zip fasteners hooks and poppers Tie any belt
9. User manual EATERS n 9 6 Washing machine BEACH ZWH7120 P 147214520 MANUAL la vita bella ZANUSSI ITALIAN SINCE 1916 Contents Safety information v cceceeeeee rere 2 ENVIFONMENT CONCEMS 4 Product descriptioN 5 TechnICaldala aaa 5 Installation aaa 6 FIPS USES iaia 8 Dall USE viscisscenrntearnvenchinaesbien ani 8 Safety information A Important e Inthe interest of your safety and to ensure the correct use before installing and first using the appliance read this user manual carefully including its hints and warnings e To avoid unnecessary mistakes and accidents it is important to ensure that all people using the appliance are thoroughly familiar with its operation and safety features e Save these instructions and make sure that they remain with the appliance if it is moved or sold so that everyone using it through its life will be properly informed on appliance use and safety General safety e itis dangerous to alter the specifications or attempt to modify this product in anyway e During high temperature wash program the door glass may get hot Do not touch it e Make sure that small pets do not climb into he drum To avoid this please check into he drum before using the appliance e Any objects such as coins safety pins nails screws stones or any other hard sharp material can cause extensive damag a
10. aken when moving it When unpacking the appliance check that it is not damaged If in doubt do not use it and contact the Service Centre All packing and transit bo emoved before use Seri occur to the product and is not adhered to See re ts must be ous damage can to property if this vant section in he user manual After having installed the appliance check hat it is not standing on the inlet and drain hose and the worktop is not pressing the electrical supply cable the machine is situated on a carpeted oor please adjust the feet in order to allow o circulate freely gt ways be sure that there is no water kage from hoses and their connections he installation E 2 p T gt 2 5 plumbing work required to install this iance should be carried out by a ified plumber QOH gt 23 electrical work required to install this iance should be carried out by a ified electrician Q 9 Use This appliance is designed for domestic use It must not be used for purposes other than those for which it was designed Only wash fabrics which are designed to be machine washed Follow the instructions on each garment label Do not overload the appliance See the relevant section in the user manual Before washing ensure that all pockets are empty and buttons and zips are fastened Avoid washing frayed or torn articles and reat stains such
11. chine off by program which is running the corresponding uming the selector dial to Off After about 3 light starts to flash Depress the button again to inutes the door can be opened pay attention restart the program to the water level and temperature i International wash code symbols These symbols appear on fabric labels in order to help you choose the best way to treat your laundry 7 Max wash Max wash Max wash i 9 wash temperature temperature temperature temperature wY 95 C 60 40 C i S0 G i Hand wash Do not wash a7 at all Delicate wash Do not bleach P Do not iron Dry cleaning Dry cleaning in perchlorethylene i Dry cleaning in petrol in all solvents petrol pure alcohol R111 amp R 113 pure alcohol and R 113 high f temperature ZN low On the lne On clothes temperature hanger Tumble dry tumble dry Programs informations Off Cancelling Off Cottons Cottons Prewash Cottons Economy Synthetics Mixed Fabric Delicates Handwash Wool Rinse Drain Spin Easy Iron Blanket Mini 30 Jeans To reset a programme and to switch off the machine turn the selector dial to Off Now a new programme can be selected Washing programme for white and coloured cottons fabrics select this program if you wish your laundry to be prewashed at 30 C before the main wash select this program if you wish your laundry to b
12. e until the groove is vertical Environment concerns Packaging materials The materials marked with the symbol rs are recyclable gt PE lt polyethylene gt PS lt polystyrene gt PP lt polypropylene This means that they can be recycled by disposing of them properly in appropriate collection containers Old machine Use authorised disposal sites for your old appliance Help to keep your country tidy The symbol se on the product or on its packaging indicates that this product may not be treated as household waste Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environmen and human health which could otherwise be caused by inappropriate waste handling of this product For more detailed information about recycling of this product please contact your local city office your household waste disposal service o Ecological hints To save water energy and to help protect the nvironment we recommend that you follow these tips e Normally soiled laundry may be washed without prewashing in order to save detergent water and time the environment is protected too e The machine works more economically if it is fully loaded he shop where you purchased the product e With ade
13. e washed is slightly normally soiled cottons This program will obtain good washing results whilst saving energy Washing programme for synthetic or mixed fabrics Highly energy efficient cold wash programme for lightly soiled laundry This programme requires a detergent which is active in cold water Washing programme for delicate fabrics Washing programme for machine washable wool as well as for hand washable woollens and delicate fabrics with the hand washing amp care symbol With this programme it is possible to rinse and spin cotton garments which have been washed by hand The machine performs 3 rinses followed by a final spin at maximum speed The spin speed can be reduced by pressing Spin button For emptying out the water of the last rinse in programmes with the Rinse Hold option Turn first the programme selector dial to Off then select programme Drain and press the Start Pause button Separate spin for hand washed garments and after programmes with Rinse Hold option Before selecting this programme the selector dial must be turned to Off You can choose the speed by means of the relevant button to adapt it to the fabrics to be spun Selecting this programme the laundry is gently washed and spun to avoid any creasing In this way ironing is easier Furthermore the machine will perform some additional rinses This programme can be used only for cotton and synthetic fabrics A gentle progra
14. elay Start N clothes Short spin K Synthetics and delicates Main wash at Spin Reduction 2 5 Mini30 lightly soiled items or 30 C Maximum 700 rpm kg 30 c Which only needs Rinses Delay Start freshening up Short spin Trousers shirts or Main wash at Spin Reduction 2S Jeans jackets in denim and Cold 60 C Rinse Hold kg Cold 60 G jersey realized with Rinses gt Daley rai hi tech materials Long spin Cottons Economy at 60 C is recommended for a full load of normally soiled cottons and is the water and energy rating label program in accordance with CEE 92 75 standards Care and cleaning A Important You must DISCONNECT the appliance from th After each wash electricity supply before you can cany out any cleaning or maintenance work Descaling The water we use normally contains lime It is a good idea to periodically use a water softening powder in the machine Do this separately from any laundry washing and according to the softening powder manufacturer s instructions This will help to prevent the formation of lime deposits Leave the door open for a while This helps to prevent mould and stagnant smells forming inside the appliance Keeping the door open after a wash will also help to preserve the door seal Maintenance Wash With the use of low temperature washes it is possible to get a build up of residues inside the drum We recommend that a maintenance wash be perfor
15. f fabric delicates woollens cottons etc the colour washing temperature and degree of soiling Only low suds Front load washer detergents should be used in this appliance e powder detergents for all types of fabric e powder detergents for delicate fabrics 60 C max and woollens e liquid detergents preferably for low temperature wash program 60 C max for all types of fabric or special for woollens only The detergent and any additives must be placed in the appropriate compartments of the dispenser drawer before starting the wash program If using concentrated powder or liquid detergents a program without prewash must be selected Any fabric softener or starching additives must be poured into the compartment marked before starting the wash program Follow the product manufacturer s recommendations on quantities to use and do not exceed the MAX mark in the detergent dispenser drawer Do not spray stain pre treatment products e g Vanish on or near the machine as it can attack plastic materials reducing its life Quantity of detergent to be used The type and quantity of detergent will depend on the type of fabric load size degree of soiling and hardness of the water used Water hardness is classified in so called degrees of hardness Information on hardness of the water in your area can be obtained from the relevant water supply company or from your local authority
16. fore pressing the Start Pause button If after having set the delay start option and pressed Start Pause button and you wish the cancel it follow the below steps e set the washing machine to PAUSE by pressing the Start Pause button e deselect the Delay start option changing the status e press the Start Pause button to start the program Important e The selected delay can be changed only after selecting he washing program again e The door will lock through out the delay time e If you need to open the door you must first set the washing machine to PAUSE by pressing the Start Pause button after that you need to wait about 2 3 minutes to elease door lock the Door Lock Dx pilot light is lashing to show the door release is in process pilot light switch off when the door can be opened The Child Lock feature will allow you to lock the controls while the machine is running to prevent tampering ACTIVATE Child Lock by pressing the Temperature and Spin buttons about 3 seconds the padlock symbol amp is displayed on the screen To DE ACTIVE Child Lock simply press the Temperature and Spin buttons about 3 seconds the padlock symbol in the screen will disappear Child Lock will remain activated until you de activate it even if the machine is tumed off The machine is provided of an acoustic device which sounds
17. m e reduce the spin speed if needed by means of th relevant button depress Start Pause button This option can be used for lightly soiled in order to obtain a good washing result in a short time The washing time will be reduced according to type of fabric and the selected temperature f an option is chosen that is not allowed with the selected program the red pilot light of the Start Pause button will flash 3 times This option is recommended for people who are allergic to detergents and in areas where the water is very soft The machine performs some additional rinses The display shows the following information e Duration of the selected program After selecting a program the duration is displayed in hours and minutes for example 2 05 The duration is calculated automatically on the basis of the maximum recommended load for each type of fabric 13 Display continues Start Pause button Delay Start Button 14 Start Pause B Delay Start Q After the program has started the time remaining is updated every minute e Delayed start The selected delay 20 hours max set by means of the relevant button appears on the display for about 3 seconds then the duration of the previously selected program is displayed The delay time value decreases by one unit every hour and then when 1 hours remain the ime decreases every minute e Incorrect option selection f an option which is not compatible
18. m designed for mixed fabrics found in delicate clothes Separate programme for lightly soiled synthetics mixed fabrics and delicates Trousers shirts or jackets in denim and jersey realized with hi tech materials The Extra Rinse option is activated automatically 17 Washing programs Program Type of laundry Description Max Temperature of program Load COTTONS 18 Cottons Cold 90 C Prewash Cold 90 C Economy 40 60 C Synthetics Cold 60 C Mixed Fabric Cold Delicates Cold 40 C Handwash Wool Cold 40 C Rinse White coloured cotton Main wash at and linen Normally Cold 90 C soiled items e g shirts Rinses underwear towels Long spin White coloured cotton Main wash at and linen Heavy soiled Cold 90 C items e g sheets Rinses tablecloths household Long spin linen White coloured cotton Main wash at and linen slightly or 40 60 C normally soiled cotton Rinses items e g shirts Long spin blouses underwear towels Synthetic or mixed fabrics Main wash at Normally soiled items Cold 60 C e g underwear coloured Rinses garments non shrink Long spin shirts blouses Mixed fabrics lightly Main wash at soiled laundry Cold Rinses Long spin Delicate fabrics Main wash at Normally soiled items Cold 40 C e g curtains acrylics Rinses viscose polyester Short spin
19. med on a regular basis 19 To run a maintenance wash e The drum should be empty of laundry Select the hottest cotton wash program e Use anormal measure of detergent must be a powder with biological properties External cleaning Clean the exterior cabinet of the appliance with soap and water only and then dry thoroughly Cleaning the dispenser drawer The washing powder and additive dispenser drawer should be cleaned regularly Remove the drawer by pressing the catch downwards and by pulling it out Flush it out under a tap to remove any traces of accumulated powder To aid cleaning the top part of the additive compartment should be removed Cleaning the drawer recess Having removed the drawer use a small brush to clean the recess ensuring that all washing powder residue is removed from the upper and lower part of the recess 20 use a small brush to clean the recess Replace the drawer and run the rinse programme without any clothes in the drum Cleaning the drain filter Drain filter collects lint and other items left in the dirty laundry to prevent pump blockage The pump must be cleaned regularly To clean the filter proceed as follows e Tum programme selector dial to position Off Off e Unplug the appliance e Open the door e Tum the drum and align the filter cover FILTER with the arrow on the door seal e Open the filter co
20. ncrease the detergent quantity or use another one Use commercial products to treat the stubborn stains Check if you have selected the correct temperature Introduce into the drum less laundry Wait the end of washing cycle Wait about 8 minutes Select drain or spin program to empty out the water Check the correct installation of the appliance Check the correct levelling of the appliance The laundry is not evenly distributed in the drum Maybe there is very little laundry in the drum Unstable floors eg wooden floors The machine is fitted with a type of motor which makes an unusual noise compared with other traditional motors This new motor ensures a softer start and more even distribution of the laundry in the drum when spinning as well as increased stability of the machine Redistribute the laundry Load more laundry 23 Maitunction __ Possible cause Solution The electronic unbalance detection Redistribute the laundry device has cut in because the th Spinning starts m laundry is not evenly distributed in e drum The laundry is redistributed by reverse rotation of the drum This ay happen several times before the late or the unbalance disappears and normal machine does not 5 spin m d Ww t pinning can resume If after 10 inutes the laundry is still not evenly stributed in the drum the machine ill not spin In this case redistribute e load man
21. nd must not be placed into the machine CONTOl Panel rara 11 Set your washing program 12 International wash code symbols 15 Programs INformations 16 Washing programs 17 Care and cleaning 18 Something Not Working 22 Only use the advised quantities of fabric softener and detergent Damage to the fabric can ensue if you overfill Refer to the manufacturer s recommendations of quantities e This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the applianc by a person responsible for their safety e Wash small items such as socks laces washable belts etc in a washing bag or pillow case as it is possible for such items to slip down between the tub and the inner drum e Do not use your washing machine to wash articles with whalebones material without hems or tom material e Always unplug the appliance and tum off the water supply after use and before cleaning or maintenance e Under no circumstances should you attempt to repair the machine yourself Repairs carried out by inexperienced persons may cause injury or serious malfunctioning Contact your local Service Centre Always insist on genuine spare parts Installation This appliance is heavy Care should be
22. quate pre treatment stains and limited soiling can be removed the laundry can then be washed at a lower temperature e Measure out detergent according to the water hardness the degree of soiling and the quantity of laundry being washed Product description Front View Back View 1 Detergent Dispenser Drawer g Rating Plate 11 Water Drain Hose A Worktop Front Feet A Hose Holders E Control Panel 8 Water Inlet Hose IE Back Feet 4 Door Opening Handle O Drain Hose Support E Drain Fiter HI Mains Cable Technical data Dimensions Width 60 cm Height 85 cm Depth 54 cm Power supply voltage frequency 220 240 V 50 Hz Total power absorbed 2000 W Minimum fuse protection 10A Water supply pressure inimum 0 05 MPa aximum 0 8 MPa Maximum Load Cottons 7 0 kg Synthetics 2 5 kg Delicates 25 k Hand Wash 2 0 kg Spin Speed aximum 1200 rom Installation Unpacking A Important All transit bolts and packing must be removed before using the appliance You are advised to keep all transit devices so that they can be refitted if the machine ever has to be transported again e Using a spanner unscrew and remove the two rear bottom screws e Slide out the two plastic pins e Lay the machine on its back ensuring that the hoses are not crushed Place one of the polystyrene angle packings under the machine e Remove the polystyrene block A protecting the motor Ver
23. relevant paragraph in water drainage section Check the drain hose connection Red Start Pause pilot light flashes The drain filter is clogged Red Start Pause pilot light flashes The option Rinse Hold has been selected The laundry is not evenly distributed in the drum Clean the drain filter Disable the option Rinse Hold or select Spin program Redistribute the laundry Maitunction __ Possible cause Solution mr There is water on the floor Unsatisfactory washing results The door will not open The machine vibrates or is noisy The machine makes an unusual noise Too much detergent or unsuitabl detergent creates too much foam has been used Check whether there are any leaks from one of the inlet hose fittings It is not always easy to see this as the water runs down the hose check to see if it is damp The drain hose is damaged Too little detergent or unsuitable detergent has been used Stubborn stains have not been treated prior to washing The correct temperature was not selected Excessive laundry load The program is still running The door lock has not been released There is water in the drum The transit bolts and packing have not been removed The support feet have not been adjusted Reduce the detergent quantity or use another one Check the water inlet hose connection Change it with a new one I
24. s or long apes e Ensure that the electrical and water connections comply with the installation instructions e Rub particularly soiled areas with a special detergent or detergent paste Treat curtains with special care Remove hooks or tie them up in a bag or net Removing stains Stubbom stains may not be removed by just water and detergent It is therefore advisable to treat them prior to washing Blood treat fresh stains with cold water For dried stains soak overnight in water with a special detergent then rub in the soap and water Oil based paint moisten with benzine stain remover lay the garment on a soft cloth and dab the stain treat several times Dried grease stains moisten with turpentine lay the garment on a soft surface and dab the stain with the fingertips and a cotton cloth Rust oxalic acid dissolved in hot water or a rust removing product used cold Be careful with rust stains which are not recent since the cellulose structure will already have been damaged and the fabric tends to hole Mould stains treat with bleach rinse well whites and fast coloureds only Grass soap lightly and treat with bleach whites and fast coloureds only Ball point pen and glue moisten with acetone lay the garment on a soft cloth and dab the stain Lipstick moisten with acetone as above then treat stains with methylated spirits Remove any residual marks from
25. te the hose and retighten the fitting making sure there are no water leaks The inlet hose must not be lengthened If it is too short and you do not wish to move the tap you will have to purchase a new longer hose specially designed for this type of use Water drainage The end of the drain hose can be positioned in three ways Hooked over the edge of a sink using the plastic hose guide supplied with the machine In this case make sure the end cannot come unhooked when the machine is emptying This could be done by tying it to the tap with a piece of string or attaching it to the wall In a sink drain pipe branch This branch must be above the trap so that the bend is at least GO cm above the ground Directly into a drain pipe at a height of not less than 60 cm and not more than 90 cm The end of the drain hose must always be ventilated i e the inside diameter of the drain pipe must be larger than the outside diameter of he drain hose The drain hose must not be kinked Run it along he floor only the part near the drainage point must be raised For the correct functioning of the machine the drain hose must remain hooked on the proper support piece situated on the top part of back side of the appliance Electrical Connection This machine is designed to operate on a 220
26. ually and select the spin programme Machines based on modem No water is visible technology operate very in the drum economically using very little water WI ithout affecting performance If you are unable to identify or solve the problem contact our service centre Before telephoning make a no te of the model serial number and purchase date of your machine the Service Centre will require this information e Model description MOD ee e Product number PNC e Serial number S N ccccccccccceeeeeeereaes Ser No 24
27. ver by pressing the special hook and by rotating the cover upwards Hold filter securly and pull upwards to remove it from its position e Remove eliminate the eventual fluff or small objects around the filter e Clean the filter under the water tap e After cleaning the filter open the filter cover and insert the filter back to its position A Important The filter is inserted correctly when the indicator on this top is visible and you will hear Click sound e close the filter cover e insert the mains plug again A Important Do not start washing clothes without the filter in its place Cleaning the water inlet filter If your water is very hard or contains traces of lime deposit the water inlet filter may become clogged It is therefore a good idea to clean it from time to time e Tum off the water ap e Unscrew the water inlet hose e Clean the filter using a hard bristle brush e Tighten up the inlet hose 21 Something not working Certain problems are due checks listed below During machine operation the machine is not working Once the problem has be after all checks the proble o lack of simple maintenance or oversights which can be solved easily without calling out an engineer Before contacting your local Service Centr please carry out the it is possible that the red Start Pause
28. white fabrics with bleach Red wine soak in water and detergent rinse and treat with acetic or citric acid then rinse Treat any residual marks with bleach Ink depending on the type of ink moisten the fabric first with acetone then with acetic acid treat any residual marks on white fabrics with bleach and then rinse thoroughly Tar stains first treat with stain remover methylated spirits or benzine then rub with detergent paste do not use acetone on artificial silk Load the laundry Open the door by carefully pulling the door handle outwards Place the laundry in the drum one item at atime shaking them out as much as possible Close the door i Maximum loads Recommended loads are indicated in the program charts General rules e Cotton linen drum full but not too tightly packed e Synthetics drum no more than half full e Delicate fabrics and woollens drum no more than one third full Washing a maximum load makes the most efficient use of water and energy For heavily soiled laundry reduce the load size Detergents and additives Good washing results also depend on the choice of detergent and use of the correct quantities to avoid waste and protect the environment Although biodegradable detergents contain substances which in large quantities can upset the delicate balance of nature The choice of detergent will depend on the typ o
29. with the set wash programme is selected the message Err is displayed or about 2 seconds and the integrated red Start Pause ight start flashing Alarm codes n the event of operating problems some alarm codes can be displayed for example E28 see paragraph Something not working e End of programme When the program has finished a flashing zero is displayed e Door open When the door has not been closed a flashing 40 is displayed To start the selected program press the Start Pause button the corresponding green pilot light stops ashing To interrupt a program which is running depress the Start Pause button the corresponding green pilot ight starts to flash To restart the program from the point at which it was interrupted press the Start Pause button again you have chosen a delayed start the machine will begin the countdown Before you start the program this option makes it possible to delay the starting of the washing program by 30 min 60 min 90 min 2 hours and then by 1 hour till 20 hours The selected delay time will appear on the display for about 3 seconds then the duration of the program will appear again Delay Start Button continues Child Lock Option Temp Spin SI Acoustic Signals Option Rinse Hold Super Quick RA The above options must be selected after choosing the wash program with the dial and be
30. y carefully remove the front polystyrene block B by gently pulling the polyethylene bag 1 downwards then 2 out ensuring not to tear the bag Some models are provided with a bottom cover that will be found inside the washing machine drum After ensuring the polyethylene bags have been removed follow below instruction 1 Locate the bottom cover as shown in position C 2 Then push the top end to lock to the bottom of washing machine Remove the polystyrene base set th machine upright and unscrew the remaining rear screw Slide out the relevant pin Cover all the open holes with the plugs which you can find in the bag containing the instruction booklet Positioning Install the machine on a flat hard floor Make sure that air circulation around the machine is not impeded by carpets rugs etc Check that the machine does not touch the wall or cupboard units Carefully level by screwing the adjustable front fee in or out Never place cardboard wood or similar materials under the machine to compensat for any unevenness in Water inlet Connect the water inl the floor 3 4 BSP thread hose to a tap with Use the hose supplied machine DO NOT US The other end of the in with the washing E OLD HOSES et hose which ne can be tumed in connects to the machi any direction Simply loosen the fitting rota
Download Pdf Manuals
Related Search