TCM 310 Transceiver Module User Manual
Contents
1. USER MANUAL Green Smart Wireless enocean March 12 2014 Observe precautions Electrostatic sensitive devices Patent protected WO98 36395 DE 100 25 561 DE 101 50 128 WO 2004 051591 DE 103 01 678 A1 DE 10309334 WO 04 109236 WO 05 096482 WO 02 095707 US 6 747 573 US 7 019 241 EnOcean GmbH Phone 49 89 67 34 689 0 Subject to modifications Kolpingring 18a Fax 49 89 67 34 689 50 TCM 310 310C TCM 310U User Manual 82041 Oberhaching info enocean com March 13 2014 Germany www enocean com Page 1 28 gt USER MANUAL V 1 15 Green Smart Wireless enocearn TCM 310 TCM 310C TCM 310U REVISION HISTORY The following major modifications and improvements have been made to the first version of this document No Major Changes Initial version Modification for Step Code DB increased number of filters and Smart Ack mail boxes Start up time and current consumption in deep sleep mode added in 2 2 im proved layout recommendations in 3 5 1 Antenna recommendations removed and referred to application note AN102 and AN105 Maximum Rating for IOVDD modified IOVDD may now exceed VDD Ad a information in 3 6 Chapter Related Documents added pin numbers added in 3 2 update of FCC grant in 5 2 parameters for antenna requirements relaxed in 4 2 1 Error in table in 3 2 corrected pin 17 and 18 need to be connected to GND as shown in figure above Supply voltage range extended start up tim2. USER MANUAL V 1 15 enocean TCM 310 TCM 310C TCM 310U 3 2 1 GPIO supply voltage IOVDD For digital communication with other circuitry the pins of the serial interface UART may be operated from supply voltages different from DVDD Therefore an interface voltage supply pin IOVDD is available which must be connected either to DVDD or to an external supply within the tolerated voltage range of IOVDD A A 3 3 Green Smart Wireless If DVDD 0 V e g in any sleep mode or if VDD VOFF and IOVDD is supplied there may be unpredictable and varying current from IOVDD caused by internal floating nodes It must be taken care that the current into IOVDD does not exceed 10 mA while DVDD 0 V If DVDD 0 V and IOVDD is not supplied do not apply voltage to any above mentioned pin This may lead to unpredictable malfunction of the device IOVDD voltage must not exceed VDD voltage A malfunction of the module may be caused by such inverse supply Absolute maximum ratings non operating Symbol Parameter Min Max Units VDD Supply voltage at VDD 205 amp E5 V IOVDD GPIO supply voltage 0 5 3 6 V GND Ground connection 0 0 V VINDi Voltage at RESET and UART 0 5 36 V 3 4 Maximum ratings operating Symbol Parameter Min Max Units Supply voltage at VDD ue TCM 310 2 6 3 5 V IOVDD GPIO supply voltage see also 3 2 1 1 7 3 6 V GND Ground connection 0 0 V VIND1 Voltage a
3. Time tSmin to tSmax 60 180 seconds Time maintained above Temperature T 217 C Time t 60 150 seconds Peak Classification Temperature Tp Time within 5 C of actual Peak Temperature tp Ramp Down Rate 6 C second max Time 25 C to Peak Temperature 8 minutes max Note 1 All temperatures refer to topside of the package measured on the package body surface me o Te I E S peaa A o H E l e Preheat 1 T i i i i i t 25 C to Peak Time gt IPC 020c 5 1 TCM 310 shall be handled according to Moisture Sensitivity Level MSL4 which means a floor time of 72 h TCM 310 may be soldered only once since one time is already consumed at production of the module itself Once the dry pack bag is opened the desired quantity of units should be removed and the bag resealed within two hours If the bag is left open longer than 30 minutes the desiccant should be replaced with dry desiccant If devices have exceeded the specified floor life time of 72 h they may be baked according IPC JEDEC J STD 033B at max 90 C for less than 60 h Devices packaged in moisture proof packaging should be stored in ambient conditions not exceeding temperatures of 40 C or humidity levels of 90 r H TCM 310x modules shall be soldered within 6 months after delivery 2014 EnOcean www enocean com TCM 310 TCM 310C TCM 310U User Manual v1 15 March
4. EEP 2 5 specification 2014 EnOcean www enocean com TCM 310 TCM 310C TCM 310U User Manual v1 15 March 2014 Page 11 28 gt USER MANUAL V 1 15 Green Smart Wireless enocean TCM 310 TCM 310C TCM 310U 4 APPLICATIONS INFORMATION 4 1 Transmission range The main factors that influence the system transmission range are type and location of the antennas of the receiver and the transmitter type of terrain and degree of obstruction of the link path sources of interference affecting the receiver and dead spots caused by signal reflections from nearby conductive objects Since the expected transmission range strongly depends on this system conditions range tests should categorically be performed before notification of a particular range that will be attainable by a certain application The following figures for expected transmission range are considered by using a PTM a STM or a TCM radio transmitter device and the TCM radio receiver device with preinstalled whip antenna and may be used as a rough guide only Line of sight connections Typically 30 m range in corridors up to 100 m in halls Plasterboard walls dry wood Typically 30 m range through max 5 walls Line of sight connections Typically 30 m range in corridors up to 100 m in halls Ferro concrete walls ceilings Typically 10 m range through max 1 ceiling Fire safety walls elevator shafts staircases and supply areas should be considered as screenin
5. 2014 Page 21 28 USER MANUAL Green Smart Wireless enocean 4 7 Tape amp Reel specification Tape running direction 2014 EnOcean www enocean com TCM 310 TCM 310C TCM 310U User Manual v1 15 March 2014 Page 22 28 gt USER MANUAL V 1 15 Green Smart Wireless enocearnm TCM 310 TCM 310C TCM 310U 5 AGENCY CERTIFICATIONS The modules have been tested to fulfil the approval requirements for CE TCM 310 and FCC IC TCM 310C TCM 310U based on the built in firmware 5 1 CE approval The modules bear the EC conformity marking CE and conform to the R amp TTE EU directive on radio equipment The assembly conforms to the European and national requirements of electromagnetic compatibility The conformity has been proven and the according documentation has been deposited at EnOcean The modules can be operated without notification and free of charge in the area of the European Union and in Switzerland The following provisos apply e EnOcean RF modules must not be modified or used outside their specification limits e EnOcean RF modules may only be used to transfer digital or digitized data Analog speech and or music are not permitted e The final product incorporating EnOcean RF modules must itself meet the essential re quirement of the R amp TTE Directive and a CE marking must be affixed on the final product and on the sales packaging each Operating instructions containing a Declaration of Confor
6. 310 TCM 310C TCM 310U 4 5 1 Recommended foot pattern Top layer 2014 EnOcean www enocean com TCM 310 TCM 310C TCM 310U User Manual v1 15 March 2014 Page 18 28 gt USER MANUAL Green Smart Wireless enocean Solder resist top layer TCM 310 TCM 310C TCM 310U User Manual v1 15 March 2014 Page 1928 USER MANUAL Green Smart Wireless enocean Solder paste top layer The data above are also available as EAGLE library In order to ensure good solder quality a solder mask thickness of 150 um is recommended In case a 120 um solder mask is used it is recommended to enlarge the solder print The pads on the solder print should then be 0 1 mm larger than the pad dimensions of the module as specified in chapter 2 3 not relative to the above drawing Nevertheless an application and production specific test regarding the amount of soldering paste should be performed to find optimum parameters 2014 EnOcean www enocean com TCM 310 TCM 310C TCM 310U User Manual v1 15 March 2014 Page 20 28 USER MANUAL Green Smart Wireless enocean 4 6 Soldering information TCM 310x shall be soldered according to IPC JEDEC J STD 020C standard Profile Feature Pb Free Assembly Average Ramp Up Rate TSmax to Tp 3 C second max Preheat Temperature Min TSmin Temperature Max TSmax
7. APPLICATIONS INFORMATION na 12 zm Transmission FAO ass an en nn E ne RE En TER EEE RER TER 12 4 2 Antenna OPUONS serienn e entrent ee nee 13 42d COV CIVICW IU 13 4 2 2 WHIP antenna u a nr 13 4 2 3 Helical antenna sic sun nn an ann ka MUERE LEE nein ni 14 4 2 4 Chip antenna supplier Mitsubishi Material Type AM11DG STO1 15 4 3 Recommendations for laying a whip antenna cssssssssee m 16 4 4 Power supply requirements E Re eX C HR GU nn 17 4 5 Layout recommendations 444444 emen sen semen esee enne 17 4 5 1 Recommended foot pattern sise 18 4 6 Soldering information 4 4 mene mene mense menie senes enne 21 4 7 Tape amp Reel Specifications nee 22 5 AGENCY CERTIFICATIONS 4e ee sine en ee Lev sais etes racines 23 AES p eLm m 23 5 2 FCC United States Certification menester 24 5 3 IC Industry Canada Certification sisi 27 5 4 FCC Regulatory Statements eese emen nennen nn 26 5 5 Industry Canada Regulatory Statements 444444 44 nennen nn nnn 28 2014 EnOcean www enocean com TCM 310 TCM 310C TCM 310U User Manual v1 15 March 2014 Page 3 28 USER MANUAL Green Smart Wireless enocean 1 MODULE VARIANTS AND RELATED DOCUMENTS This document describes operation of TCM 310 modules available in variations for following frequencies m TCM 310 868 300 MHz m TCM 310C 315 000 MHz m TCM 310U 902 875 MHz In si
8. Insulation PVC mixture TI2 according to VDE 0207 4 TCM 310 TCM 310C TCM 310U User Manual v1 15 March 2014 Page 13 28 USER MANUAL Green Smart Wireless enocean 4 2 3 Helical antenna 315 MHz please contact EnOcean for availability 868 3 MHz according to drawing below connect to RF WHIP please contact EnOcean for MOQ Minimum GND plane 35 mm x 30 mm Minimum distance space 10 mm 902 875 MHz limited modular approval available please contact EnOcean for MOQ and mandatory limited modular approval user agreement according to drawing below connect to RF WHIP Minimum GND plane 35 mm x 30 mm Minimum distance space 10 mm 2 indungsbereich 1 Windungsbereich 0 5 Windungen Steigung 4 2 0 4 mm 2 Windungsbereich 6 65Windungen Steigung 3 1 mm gestreckte L nge 141 7 mm Doppelbema ung 1 entspricht ganze Windung 4 2 2 2 betrifft Schenkelstel lung bezogen auf Windungsanfang Windungen d rfen sich nicht ber hren CD Prifmas CUL200 0 85 0 02 FA Nr 200723 wu am Helix Antenne 868MHZ STM3xy St Hel i x antenna Er cear GrkH A99 E02 EXT Dieta idt v Hed nie 2014 EnOcean www enocean com TCM 310 TCM 310C TCM 310U User Manual v1 15 March 2014 Page 14 28 gt USER MANUAL V 1 15 Green Smart Wireless ocean TCM 310 TCM 310C TCM 310U 4 2 4 Chip antenna supplier Mitsubishi Material Type AM11DG STO1 315 MHz Modula
9. Not API programmable 2014 EnOcean www enocean com TCM 310 TCM 310C TCM 310U User Manual v1 15 March 2014 Page 4 28 USER MANUAL Green Smart Wireless enocean 2 2 Technical data Antenna TCM 310 external whip or 50 Q antenna mountable TCM 310C external whip TCM 310U external whip or Helical antenna Frequency TCM 310 868 300 MHz ASK TCM 310C 315 000 MHz ASK TCM 310U 902 875 MHz FSK Radio Standard Enocean 868 MHz 315 MHz ISO IEC 14543 3 10 Data rate Modulation type 125 kbps Receiver Sensitivity at 25 C typ 96 dBm 868 300 MHz typ 98 dBm 315 000 MHz typ 98 dBm 902 875 MHz Conducted Output Power typ 3 dBm 315 and 868 MHz 1 dBm 902 875 MHz Power Supply 2 6V 3 5 V Start up Time 500ms Serial Interface UART Current Consumption Receive mode 33 mA Transmit mode 24 mA Dimensions of PCB 22x19x3 mm Operating temperature 0 to 65 C Radio Regulations R amp TTE EN 300 220 TCM 310 v 2 4 1 FCC CFR 47 Part 15 TCM 310C TCM 310U 1 According to ISO IEC 14543 3 10 2 0 1 telegram error rate based on transmitted sub telegrams 2014 EnOcean www enocean com TCM 310 TCM 310C TCM 310U User Manual v1 15 March 2014 Page 5 28 USER MANUAL Green Smart Wireless enocean 2 3 Physical dimensions Unless otherwise specified dimensions are in mm Tolerances PCB outline dimensions 0 2 mm All other tolerances 0 1 mm T
10. and will therefore be lost after RESET or after a deep sleep phase Only Smart Ack mailboxes are stored in FLASH and are available also after RESET or a deep sleep phase After sending a CO WR RESET command the following CO READY event indi cates wake up reason 06 meaning A memory request from the CPU core does not correspond to any valid memory location This is caused by the real reset cause used when CO WR RESET will be performed It is not a SW HW malfunction 3 7 Built in Repeater TCM 310x provides the option to activate a one or two level repeater for EnOcean radio telegrams 1 level repeater If a received telegram is a valid and original not yet repeated the tele gram is repeated after a random delay This delay will be chosen such that the maximum TX maturity time as standardized in ISO 14543 3 10 of 40ms will not be exceeded 2 level repeater If a received telegram is valid and original or repeated once the telegram is repeated after a random delay This delay will be chosen such that the maximum TX ma turity time as standardized in ISO 14543 3 10 of 40ms will not be exceeded Repeated telegrams are marked as repeated by an increased repeater counter Configura tion of the repeater functionality is done via serial interface commands When using repeaters care must be taken to ensure that regulatory transmitter duty cycle limits if applicable are not exceeded conditions Otherwise the system function can be
11. government regulations are to be observed Packing Please use the recycling operators known to you 2014 EnOcean www enocean com TCM 310 TCM 310C TCM 310U User Manual v1 15 March 2014 Page 2 28 USER MANUAL Green Smart Wireless enocean TABLE OF CONTENT 1 MODULE VARIANTS AND RELATED DOCUMENTS 4 444 teens eats nennen nen 4 2 GENERAL DESCRIPTION tete mena ea Rasen 4 2 1 Basic functionality saisir eri nen en na na Korn REY na TR AR ENESTE 4 2 2 Technical data ior er 5 2 3 Physical dimensions sise 6 2 4 Environmental conditions inr er er RI exa Rt rn RR RR R YR annee NEAR ententes NER ta ana 6 2 5 Ordering information ice iik ink ee an RARE RRRRRANRRR RAE REARRRKRANKNIRARRRARARRFRTRRARANE AKA 6 3 FUNCTIONAL DESCRIPTION 4 e eee rene eee eee en nun en esie ne enn ees 7 Sel PIN QUES 7 3 2 Pin description and operational characteristics essen 7 3 2 1 GPIO supply voltage IOVDD 0 cece cece eterna nenne nenne nenne nennen 8 3 3 Absolute maximum ratings non operating ss s ssssssssrssssrrssrrrurrrrnrrrnurnrnnrrrnnrrnns 8 3 4 Maximum ratings operating meses memes 8 3 5 System enviIrontmerit eoo tereti nere er Ier bee RON DR E Paw Een 8 3 6 Serial Interface dee ee an beanie par ra rer labre 9 3 7 Built in Repeater nenne 10 3 8 Smart Acknowledge ice iso ann einen nn nn nn anne 11 3 9 Remote Management au neh 11 4
12. 5713A PTM330U STM 300U FCC ID SZV STM300U IC 5713A STM300U STM 320U FCC ID SZV STM320U 1C 5713A STM320U E STM 332U FCC ID SZV STM332U IC 5713A STM332U m TCM 300U FCC ID SZV STM300U IC 5713A STM300U TCM 310U FCC ID SZV STM300U IC 5713A STMS300U TCM 320U FCC ID SZV TCM320U IC 5713A TCM320U Green Smart Wireless enocean OEM Requirements In order to use EnOcean s FCC ID number the OEM must ensure that the following condi tions are met m End users of products which contain the module must not have the ability to alter the firmware that governs the operation of the module The agency grant is valid only when the module is incorporated into a final product by OEM integrators m The end user must not be provided with instructions to remove adjust or install the module m The Original Equipment Manufacturer OEM must ensure that FCC labeling require ments are met This includes a clearly visible label on the outside of the final product Attaching a label to a removable portion of the final product such as a battery cover is not permitted The label must include the following text TCM 310C Contains FCC ID SZV STM300C The enclosed device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions i this device may not cause harmful interference and ii this device must accept any interference received including interference that may cause undesired operation TCM 310U Cont
13. CM 310 pads on bottom side of PCB PCB Dimension 22x 19 x 3 1 mm Weight 1 99 2 4 Environmental conditions Operating temperature 0 C 65 C Storage temperature 40 C 85 C Storage temperature in tape amp reel package 20 C 50 C Humidity 0 93 r H non condensing 2 5 Ordering information Type Ordering Code Frequency TCM 310 S3003 K310 868 300 MHz TCM 310C 53033 K310 amp TCM 310U S3053 k310 2 902 875 MHz 2014 EnOcean www enocean com TCM 310 TCM 310C TCM 310U User Manual v1 15 March 2014 Page 6 28 gt USER MANUAL V 1 15 Green Smart Wireless enocean TCM 310 TCM 310C TCM 310U 3 FUNCTIONAL DESCRIPTION 3 1 Pin out GND VDD DVDD L GND mee 16MHz ua alun EO3000I n c RF_WHIP n c GND n c RF 50 nie er TOP VIEW GND RVDD Function Characteristics 1 5 7 17 18 Ground connection Must be connected to GND see 4 4 24 26 28 31 VD P Supply voltage CENT RF supply voltage Leave open regulator output Output current max 5 mA regulator output IOVDD 23 GPIO supply volt Must be connected to desired inter age face supply voltage see 3 4 See also 3 2 1 RF_50 56 RFoutpt 50Ohm output for external antenna n c 3 9 14 19 22 Not connected Do not connect 29 30 32 34 2014 EnOcean www enocean com TCM 310 TCM 310C TCM 310U User Manual v1 15 March 2014 Page 7 28
14. ains FCC ID SZV STM300U The enclosed device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions i this device may not cause harmful interference and ii this device must accept any interference received including interference that may cause undesired operation When the device is so small or for such use that it is not practicable to place the state ment above on it the information required by this paragraph shall be placed in a promi nent location in the instruction manual or pamphlet supplied to the user or alternative 2014 EnOcean www enocean com TCM 310 TCM 310C TCM 310U User Manual v1 15 March 2014 Page 25 28 gt USER MANUAL V 1 15 Green Smart Wireless enocearnm TCM 310 TCM 310C TCM 310U ly shall be placed on the container in which the device is marketed However the FCC identifier or the unique identifier as appropriate must be displayed on the device The user manual for the end product must also contain the text given above m Changes or modifications not expressly approved by EnOcean could void the user s au thority to operate the equipment m The module must be used with only the following approved antenna s Part Number Type Gain Wire Monopole 1 0 dBi Helical TCM 310U only Chip TCM 310U only m The OEM must ensure that timing requirements according to 47 CFR 15 231 a c are met m The OEM must sign the OEM Limited Modular Appro
15. aterials web site at www mmea com or email to electroniccomponents mmus com 2014 EnOcean www enocean com TCM 310 TCM 310C TCM 310U User Manual v1 15 March 2014 Page 15 28 USER MANUAL Green Smart Wireless enocean 4 3 Recommendations for laying a whip antenna Antenna too close to GND area Antenna end led back to foot point Antenna too close to GND area 2014 EnOcean www enocean com TCM 310 TCM 310C TCM 310U User Manual v1 15 March 2014 Page 16 28 USER MANUAL V 1 15 Green Smart Wireless enocearnm TCM 310 TCM 310C TCM 310U 4 4 Power supply requirements In order to provide a good radio performance great attention must be paid to the power supply and a correct layout and shielding It is recommended to place a 22 pF ceramic ca pacitor between VDD and GND close to the module material X5R X7R min 6 3 V to avoid derating effects In addition an HF SMD EMI Suppression Ferrite Bead such as the W rth WE CBF HF SMD EMI Suppression Ferrite Bead W rth order number 742863160 shall be inserted in the power supply line For best performance it is recommended to keep the ripple on the power supply rail below 10 mVpp see 3 4 All GND pins must be connected to GND Be careful not to create loops The A ground must be realized ideally on both sides of the PCB board with many vias At least there must be a short star connection Otherwise RF performance
16. can be reduced Layout recommendations It is recommended to have a complete GND layer in the application PCB at least in the area below the module and directly connected components e g mid layer of your application PCB 4 5 A The length of lines connected to I Os should not exceed 5 cm Due to unisolated test points there are live signals accessible on the bottom side of the module Please follow the following advices to prevent interference with your application circuit m We suggest avoiding any copper structure in the area directly underneath the module top layer layout of your application PCB If this is not possible in your design please provide coating on top of your PCB to prevent short circuits to the module All bare metal surfaces including vias have to be covered e g adequate layout of solder resist m It is mandatory that the area marked by the circle in the figure below is kept clear of any conductive structures in the top layer and 0 3 mm below Otherwise RF performance will be degraded Furthermore any distortive signals e g bus signals or power lines should not be routed underneath the module If such signals are present in your design we sug gest separating them by using a ground plane between module and these signal lines 2014 EnOcean www enocean com TCM 310 TCM 310C TCM 310U User Manual v1 15 March 2014 Page 17 28 gt USER MANUAL V 1 15 Green Smart Wireless enocean TCM
17. compromised by collisions of 2 level repeating function should only be activated after careful study of the radio telegrams For detailed recommendations regarding the usage of repeaters please refer to our applica tion note EnOcean Wireless Systems Installation Notes PDF 09 2010 2014 EnOcean www enocean com TCM 310 TCM 310C TCM 310U User Manual v1 15 March 2014 Page 10 28 USER MANUAL Green Smart Wireless enocean 3 8 Smart Acknowledge TCM 310x provides a post master function with 20 mailboxes for sensors using Smart Ac knowledge technology For more information on smart acknowledge please refer to the EnOcean End Equipment Profiles EEP 2 5 specification all TCM 3xy devices which are not continuously powered Otherwise these TCM 3xy modules could be declared postmaster If power supply to such postmaster will be switched off then Smart Acknowledge would not work due to the absence of the postmaster A When teaching in a device using Smart Acknowledge please take care to switch off 3 9 Remote Management TCM 310x provides a transparent radio channel also for remote management messages with a message length of up to 256 bytes This enables an external micro controller con nected to TCM 310 to handle remote management request from external devices or to con trol other devices via remote management For more information on remote management please refer to the EnOcean End Equipment Profiles
18. de this manual the following terms TCM 310x can be used interchangeably for any of the above frequency This document describes operation of TCM 310x modules with their built in firmware In addition we recommend following our application notes in particular AN101 Power Supply Layout Layout considerations for Line Power AN102 Antenna Basics Basic Antenna Design Considerations for EnOcean based Products AN105 315 MHZ Internal Antenna Design Considerations for EnOcean based Products The specification of the serial protocol ESP3 can be found here http www enocean com en enocean modules tcm 310 2 GENERAL DESCRIPTION 2 1 Basic functionality TCM 310x is a SMD mountable radio transmitter mod ule enabling the realization of gateways for EnOcean 868 MHz 315 MHz and 902 MHz radio systems It pro vides a bi directional radio interface and a bi directional serial interface Radio messages are sent transparently through the serial interface in both direc tions from and to an externally connected host proces sor or host PC In addition control commands can be sent from the host e g to configure the repeater func tionality or to manage Smart Ack functions TCM 310x can act as postmaster for up to 20 bi directional sen sors using Smart Ack technology Features m Smart Ack controller functionality Transparent radio channel Programmable repeater functionality 1 2 Level ESP3 support EnOcean Serial Protocol V3
19. e l ext rieur d une partie non amovible du produit final doit contenir le texte suivant CM 310C Contains IC 5713A STM300C Contient le module d mission IC 5713A STM300C TCM 310U Contains IC 5713A STM300U Contient le module d mission IC 5713A STM300U m L OEM doit signer l accord OEM limit e Approbation modulaire avec EnOcean 2014 EnOcean www enocean com TCM 310 TCM 310C TCM 310U User Manual v1 15 March 2014 Page 27 28 USER MANUAL Green Smart Wireless enocean 5 5 Industry Canada Regulatory Statements This device complies with Industry Canada licence exempt RSS standard s Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device Le pr sent appareil est conforme aux CNR d Industrie Canada applicables aux appareils radio exempts de licence L exploitation est autoris e aux deux conditions suivantes 1 l appareil ne doit pas produire de brouillage et 2 l utilisateur de l appareil doit accepter tout brouillage radio lectrique subi meme si le brouillage est susceptible d en compro mettre le fonctionnement IMPORTANT Tous les changements ou modifications pas express ment approuv s par la partie responsable de la conformit ont pu vider l autorit de l utilisateur pour actioner cet quipment This Class B digital ap
20. e from sleep added TCM 310U added Mitsubishi Materials Chip Antenna added to limited modular approval Updated power supply filter recommendation Added Start up Time Parameter Changed Vmin 04 05 1 Published by EnOcean GmbH Kolpingring 18a 82041 Oberhaching Germany www enocean com info enocean com phone 49 89 6734 6890 EnOcean GmbH All Rights Reserved Important This information describes the type of component and shall not be considered as assured characteris tics No responsibility is assumed for possible omissions or inaccuracies Circuitry and specifications are subject to change without notice For the latest product specifications refer to the EnOcean web site http www enocean com As far as patents or other rights of third parties are concerned liability is only assumed for modules not for the described applications processes and circuits EnOcean does not assume responsibility for use of modules described and limits its liability to the replacement of modules determined to be defective due to workmanship Devices or systems contain ing RF components must meet the essential requirements of the local legal authorities The modules must not be used in any relation with equipment that supports directly or indirectly human health or life or with applications that can result in danger for people animals or real value Components of the modules are considered and should be disposed of as hazardous waste Local
21. eset system log from device data base o CO WR BIST to perform flash BIST operation o CO WR IDBASE to write ID range base number o CO RD IDBASE to read ID range base number o CO WR REPEATER to configure repeater functionality o CO RD REPEATER to read repeater state o CO WR FILTER ADD to add filter to filter list up to 30 filters are supported o CO WR FILTER DEL to delete filter from filter list o CO WR FILTER DEL ALL to delete all filter o CO WR FILTER ENABLE to enable disable supplied filters o CO RD FILTER to read supplied filters o CO WR WAIT MATURITY to wait maturity time before returning radio telegrams o CO WR MEM for writing into memory o CO RD MEM for reading memory o CO RD MEM ADDRESS to get addresses of special areas m Type 6 Smart Acknowledge commands o SA_WR_LEARNMODE to set reset Smart Acknowledge learn mode SA_RD_LEARNMODE to get learn mode SA_WR_LEARNCONFIRM to add or delete a mailbox of a client SA_WR_RESET to send a reset command to a client SA_RD_LEARNEDCLIENTS to get learned mailboxes clients o SA_WR_POSTMASTER to activate deactivate post master functionality m Type 7 Remote Management messages up to 256 Bytes o http www enocean com en enocean modules tcm 310 2014 EnOcean www enocean com TCM 310 TCM 310C TCM 310U User Manual v1 15 March 2014 Page 9 28 USER MANUAL Green Smart Wireless enocean All configuration values set via ESP3 commands are held in RAM
22. g The angle at which the transmitted signal hits the wall is very important The effective wall thickness and with it the signal attenuation varies according to this angle Signals should be transmitted as directly as possible through the wall Wall niches should be avoided Other factors restricting transmission range Devices mounted on metal surfaces shielding and detuning of antenna may cause heavy loss of transmission range Hollow lightweight walls filled with insulating wool on metal foil Suspended ceilings with panels of metal or carbon fibre Lead glass or glass with metal coating steel furniture The distance between EnOcean receivers and other transmitting devices such as com puters audio and video equipment that also emit high frequency signals should be at least 0 5 m A summarized application note to determine the transmission range within buildings is available as download from www enocean com 2014 EnOcean www enocean com TCM 310 TCM 310C TCM 310U User Manual v1 15 March 2014 Page 12 28 USER MANUAL V 1 15 Green Smart Wireless enocean TCM 310 TCM 310C TCM 310U 4 2 Antenna options 4 2 1 Overview Several antenna types have been investigated by EnOcean Please refer to our application notes AN102 and AN105 which give an overview on our recommendations All TCM 310x modules have been approved with whip antenna and TCM 310U with helical antenna in addition 868 300 MHz modules used
23. ic Activation The radio module also can be configured to transmit a short packetized control signal if triggered automatically by a relevant change of its inputs or in response to receiving a signal from another transmitter for example Again the packet contains a control signal that is intended to control something at the receiving end and may also contain data As above it is possible for the packet to get lost and never reach the receiver However if enough energy is available from the energy source and the module has been configured to do so then another packet or packets containing the control signal may be transmitted at a later time The device is capable to operate as a repeater which can receive signals from the following list of FCC IC approved transmitters and retransmit the signals TCM 310C 315 MHz m PTM 200C FCC ID SZV PTM200C IC 5713A PTM200C STM 110C FCC ID SZV STM110C IC 5713A STM110C TCM 200C FCC ID SZV TCM2XXC IC 5713A TCM2XXC TCM 220C FCC ID SZV TCM2XXC IC 5713A TCM2XXC TCM 300C FCC ID SZV STM300C IC 5713A STM300C 2014 EnOcean www enocean com TCM 310 TCM 310C TCM 310U User Manual v1 15 March 2014 Page 24 28 USER MANUAL V 1 15 TCM 310 TCM 310C TCM 310U TCM 310C FCC ID SZV STM300C IC 5713A STM300C STM 300C FCC ID SZV STM300C IC 5713A STM300C TCM 320C FCC ID SZV TCM320C IC 5713A TCM320C TCM 310U m PTM 210U FCC ID SZV PTM210U IC 5713A PTM210U B PTM 330U FCC ID SZV PTM330U IC
24. in Europe do not need additional approval if alternative used external antenna fulfils the following requirements Frequency 868 300 MHz Antenna must be suited for this band band ISM Antenna type Passive Mandatory for radio approval Impedance 50 Ohm Mandatory for radio approval Maximum gain lt 0 dBd Mandatory for radio approval In addition it is important to fulfill the following requirements in order to achieve compati bility with other EnOcean products and to ensure excellent EMI robustness VSWR lt 3 1 Important for compatibility with EnOcean protocol Return Loss gt 6 dB Important for compatibility with EnOcean protocol Bandwidth lt 20 MHz Important if 10 V m EMI robustness required for device A For 315 MHz 902 875 MHz modules TCM 310C TCM 310U please note that a full approval is needed if modules are used with antennas other than the specified antennas 4 2 2 Whip antenna 315 MHz Antenna 150 mm wire connect to RF_WHIP Minimum GND plane 50 mm x 50 mm Minimum distance space 10 mm 868 3 MHz Antenna 86 mm wire connect to RF_WHIP Minimum GND plane 38 mm x 18 mm Minimum distance space 10 mm 902 875 MHz Antenna 64 mm wire connect to RF_WHIP Minimum GND plane 50 mm x 50 mm Minimum distance space 10 mm 2014 EnOcean www enocean com 0 8 tinned bared twisted and tinned Cu wire LiY according to VDE 0812 or 0245 CI 5 or CI 6
25. is designed to comply with has been tested according to 15 231 a c and has been found to comply with each requirement Thus a finished device containing the TCM 310C TCM 310U radio module can be operated in the United States without additional Part 15 FCC approval approval s for unintentional radiators may be required for the OEM s finished product under EnO cean s FCC ID number This greatly simplifies and shortens the design cycle and develop ment costs for OEM integrators The module can be triggered manually or automatically which cases are described below Manual Activation The radio module can be configured to transmit a short packetized control signal if trig gered manually The module can be triggered by pressing a switch for example The packet contains one or more control signals that is are intended to control some thing at the receiving end The packet may also contain data Depending on how much en ergy is available from the energy source subsequent manual triggers can initiate the transmission of additional control signals This may be necessary if prior packet s was were lost to fading or interference Subsequent triggers can also be initiated as a pre caution if any doubt exists that the first packet didn t arrive at the receiver Each packet that is transmitted regardless of whether it was the first one or a subsequent one will only be transmitted if enough energy is available from the energy source Automat
26. m Increase the separation between the equipment and receiver 2014 EnOcean www enocean com TCM 310 TCM 310C TCM 310U User Manual v1 15 March 2014 Page 26 28 U SER MANUAL Green Smart Wireless enocean Connect the equipment into an outlet on a circuit different from that to which the re ceiver is connected Consult the dealer or an experienced radio TV technician for help 5 4 IC Industry Canada Certification In order to use EnOcean s IC number the OEM must ensure that the following conditions a re met Labeling requirements for Industry Canada are similar to those required by the FCC The Original Equipment Manufacturer OEM must ensure that IC labeling requirements are met A clearly visible label on the outside of a non removable part of the final prod uct must include the following text TCM 310C Contains IC 5713A STM300C Contient le module d mission IC 5713A STM300C TCM 310U Contains IC 5713A STM300U Contient le module d mission IC 5713A STM300U m The OEM must sign the OEM Limited Modular Approval Agreement with EnOcean Pour utiliser le num ro IC EnOcean le OEM doit s assurer que les conditions suivantes sont remplies m Les exigences d tiquetage pour Industrie Canada sont similaires ceux exig s par la 1 FCC Le fabricant d quipement d origine OEM doit s assurer que les exigences en mati re d tiquetage IC sont r unies Une tiquette clairement visibl
27. mity has to be attached e If the transmitter is used according to the regulations of the 868 3 MHz band a so called Duty Cycle of 1 per hour must not be exceeded Permanent transmitters such as radio earphones are not allowed e The module must be used with only the following approved antenna s Type Parameter Value Wire Monopole at RF_WHIP Maximum gain 1 0 dBi External antenna at RF 50 Antenna type Passive Impedance 50 Ohm Maximum gain lt 0 dBd 2014 EnOcean www enocean com TCM 310 TCM 310C TCM 310U User Manual v1 15 March 2014 Page 23 28 gt USER MANUAL V 1 15 Green Smart Wireless enocearnm TCM 310 TCM 310C TCM 310U 5 2 FCC United States Certification TCM 310C TCM 310U LIMITED MODULAR APPROVAL This is an RF module approved for Limited Modular use operating as an intentional trans mitting device with respect to 47 CFR 15 231 a c and is limited to OEM installation The module is optimized to operate using small amounts of energy and may be powered by a battery The module transmits short radio packets comprised of control signals in some cases the control signal may be accompanied with data such as those used with alarm sys tems door openers remote switches and the like The module does not support continu ous streaming of voice video or any other forms of streaming data it sends only short packets containing control signals and possibly data The module
28. paratus complies with Canadian ICES 003 Cet appareil num rique de la classe B est conforme la norme NMB 003 du Canada 2014 EnOcean www enocean com TCM 310 TCM 310C TCM 310U User Manual v1 15 March 2014 Page 28 28
29. r approval not available Range and gain significantly reduced because of antenna size vs the wavelength Small chip antennas at this frequency may be suited for space constrained applications Check with supplier for matching circuit and board design guide lines Supplier can make recommendations or do testing to optimize individual PCB design 868 3 MHz Additional matching circuit and proper board design is required Check with supplier for matching circuit and board design guidelines Connect matching circuit to RF 50 using 50 Ohm strip lines Please follow 902 MHz board design recommendations and dimensions Be aware that matching values differ 902 875 MHz Limited modular approval is available Please contact EnOcean to sign the mandatory lim ited modular approval user agreement Dimensions may not be shortened Matching circuit is part of the limited modular approval and may not be changed Minimum top and bottom side ground plane required as shown below Connect ground planes using multiple via as shown Connect matching circuit to RF 50 Use High Q wire wound inductors e g 0603 Murata LOW 18A series Matching circuits values L1 3 9 nH L2 33 nH L3 12 nH This antenna evaluation board is available upon request for use with EnOcean EDK 350 de veloper kit k pe 65mm 8 5mm PCB material FR4 and thicknes s Smr must be matched For any further questions or chip antenna quotes please refer to Mitsubishi M
30. t RESET and UART 0 3 6 V VDDR Max ripple at VDD 50 mVpp 3 5 System environment In the figure below TCM 310x is shown in a typical system environment Unidirectional Sensor or Switch Radio Gateway 2014 EnOcean www enocean com Smart Ack Smart Ack Sensor STM300 With API SmartAck TCM 310 TCM 310C TCM 310U User Manual v1 15 March 2014 Page 8 28 gt USER MANUAL V 1 15 Green Smart Wireless enocearnm TCM 310 TCM 310C TCM 310U 3 6 Serial Interface TCM 310x provides a bi directional serial interface which conforms to the EnOcean ESP3 specification For details regarding ESP3 please refer to the ESP3 specification The data rate on the serial interface is 58 8 kbit s which is usually interoperable with systems run ning at 57 6 kbit s Direction Nominal serial data rate Tolerance TX sent by module 58823 bit s 57600 bit s 2 196 RX received by module 58823 bit s The following ESP3 commands are supported m Type 1 Radio command for transparent mode m Type 2 Responses m Type 4 Event o SA CONFIRM LEARN to confirm discard learn in out o CO READY to indicate wake up from deep sleep initiated by CO WR SLEEP m Type 5 Common commands o CO WR SLEEP to enter energy saving mode deep sleep mode o CO WR RESET to reset the device o CO RD VERSION to read SW HW versions chip ID etc o CO RD SYS LOG to read system log from device data base o CO WR SYS LOG to r
31. val Agreement with EnOcean 5 3 FCC Regulatory Statements This device complies with part 15 of the FCC rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired opera tion Any changes or modifications not expressly approved by manufacturer could void the user s authority to operate the equipment IMPORTANT Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this equipment NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a par ticular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures m Reorient or relocate the receiving antenna
Download Pdf Manuals
Related Search