ORB-400 - Billebro
Contents
1. 09T ANZSH09T a MO BA ping 504 puepueys apo 99035 Pinja B03 BING AN6GZS 09T aJI T AN8Z2S 09T maa nnay uondussag apo Y10145 NN69S 09T AASOS DOT SpIN PJEPUEYs 43440 VEY adua 40c SeT PIN mous Ajijenb ysIH pin moug pin moug SAMS ANZ2S 09T AM ANGELS OST SAMS ANSLS 09T AM T ANFAS OST Wim asn 104 syns y uoqdusag SUNnjOA 3po 4203s NP9S 09T 3y81 AN ul moja yoiym sayqqng yar piny agang An NME9S 09T MNZIS ONT NN09S 09T NNZSH 0SI sa qgng sulyse sug ys pini a jqqng HEY PIN 3 5199H3 x b 5 160 462UK User Manual2. E qtx ORB 400 BUBBLE HAZE MACHINE Item ref 160 462UK User Manual www avsi qtx com an AVS group brand E qtx A Caution Please read this manual carefully before operating Damage caused by misuse is not covered by the warranty Introduction Thank you for choosing the ORB 400 bubble haze machine for stage and events special effects This product is designed to produce bubbles haze or a combination of both for atmospheric special effects Please read these instructions in full to gain the best results from this item and avoid damage to the unit through misuse Unpacking Your ORB 400 should reach you in good condition and should be supplied with IEC mains lead s wired remote timer control wireless plug in receiver and keyfob remote If there are any signs of damage or items missing from the packaging contact your dealer immediately Warning To prevent risk of fire or electric shock do not expose electrical parts to rain or moisture If liquids are spilled on areas other than the fluid bath or tank disconnect the mains allow the ORB 400 to dry out and have it checked by qualified personnel before further use Avoid any impact dropping or extreme pressure to the housing No user serviceable parts inside do not open the case Allow the ORB 400 to acclimatize to room temperature before operating Refer all servicing to qualified service personnel Placement The ORB 400 has built in fluid containers and should be op
3. an be varied by adjusting the rotary Output control 7 Pressing the Timer button 1 will activate the hands free timer function and the timer LED 4 will light The Interval control 8 adjusts the time between haze effect output in each timer cycle The Duration control 9 adjusts the length of time that haze is produced in each timer cycle Combined ORB effect If the bubble wheel is switched on when haze is being produced the haze passes through the bubble wands to fill each bubble with fog This gives a cloudy white appearance to the bubbles and produces a small puff of smoke when each bubble pops Alongside the combined effect the ORB 400 can perform separately as a fully functional haze or bubble machine by simply switching off the function that is not required Specifications Power supply 230Vac 50Hz IEC Bubble remote control frequency 433MHz Haze remote control functions Timer Continuous Manual Interval Output Duration Haze fluid tank capacity 2 3 litres 400W 4 5 minutes 300 x 260 x 645mm 10 15kg 160 462UK User Manual E qtx Troubleshooting Warning Hot components Switch off and allow to cool before touching the unit No light on mains switch OY light stays of Ready lights on but no haze output o manual or continuous If blocked clean with fog machine cleaner 8 distilled water No haze output on Ensure timer button is pressed in and timer LED is lit timer function Check interval dur
4. and bubble fluid to create each effect It is recommended to use one of each from the range of qtx haze and bubble fluids for best results A chart for recommended fluids is included further along in this document Unscrew the top cap of the haze fluid tank and remove to fill with the selected haze fluid Replace the cap and close securely ensuring the pipe is fed down to the bottom of the bottle so that a consistent flow of fluid is supplied to the machine Connect the remote timer control to the 5 pin DIN connector on the rear panel 3 For bubble effects fill the front fluid bath to a level covering the lowest bubble wands completely Connect the supplied wireless remote receiver to the female IEC 1 on the rear panel Connect the IEC mains lead supplied to the rear mains inlet 4 Operation Make sure that none of the remote timer control buttons are pressed in at startup Switch the mains power on 2 If bubble effect is required this will be available straight away Pressing the buttons on the wireless keyfob remote control starts and stops rotation of the wand wheel Heat up time for haze effect is usually between 4 5 minutes Haze effect is controlled via the remote timer control see below for operation During prolonged use periodically check that the fluid level is not empty After use it will be necessary to empty the bubble fluid bath 5 using the rear drain tap before moving Switch off when not in use Unplug from mains if
5. ation and output control settings test manually if necessary Ensure bubble fluid level is enough to cover the wands as they turn through the bath Check bubble wand wheel is turning press button on keyfob remote to activate No bubble output map If keyfob remote doesn t work check button cell inside and replace if necessar Check that the wireless receiver is plugged in correctly Electronic equipment and should not be disposed with other household or commercial waste at the end of its useful X Disposal The Crossed Wheelie Bin symbol on the product means that the product is classed as Electrical or mma fe The goods must be disposed of according to your local council guidelines Errors and omissions excepted Copyright 2013 AVSL Group Ltd 160 462UK User Manual E qtx WNSr 09T ANZOP D9T kapa saa aaa R an ans NNIGS 09T NNGSP D9T ANESF 09I 7 Aa kabag Da ai aT AN06S 09T 3TEH S3aUlyJeW TO Y auiysew So INGA jo SLI Spua XxZ 3 Jaueajp SUIUDEW BOY WO YNO0 O 00 NNZFF 09T 3pym anbedo yuaja 153Y3IH Jea 3 ping 304 SAS MOT Gill alab aT ANZ6S 09T MOOST 000T Sulyzew Aue Jo allym anbedo jua a0x3z Jea pinggso wniwalg BITS YN68S 09T AR peoi IN 3 IYM yoy ping Boy Ajijenb ysip dal NN9SF 09T ANSSF 09T aT WNirr9 09T aIr sS AN8855 09T aJ T anas 09T aJI S ancas 09T aJ T Anero gaT H 404 S N53Y noo HOH ad Moog 0 dn auiypew Aue Jo WUNnIpa yy aduelo ping Soy spews ysIH ANToPr 0oT ANESF
6. erated in an upright position Ensure that the ORB 400 is positioned on a stable non slip surface Safety e Check for correct mains voltage and condition of IEC lead before connecting to power outlet e Check the condition of the remote lead and ensure that it is not trapped e This unit must be earthed e This unit uses a heating element be aware that parts of the housing may be hot whilst in use Cleaning Use a soft dry or slightly damp to clean the casing Do not use strong solvents for cleaning the unit Clean the haze mechanism periodically by operating with distilled water instead of haze fluid It is also recommended to use fog machine cleaning fluid 160 670UK periodically The bubble fluid bath can be cleaned by rinsing with water draining through the rear panel tap 160 462UK User Manual E qtx Rear Panel 1 E qtx Bn REMOTE WARNING 2 ALWAYS DISCONNECT FROM POWER SUPPLY BEFORE CHANGING THE FUSE USE ONLY UNDER ADULT SUPERVISION DO NOT OPERATE WITHOUT FLUID KEEP FRONT OF MACHINE CLEAR FROM OBSTRUCTIONS WHEN OPERATING NO SERVICEABLE PARTS INSIDE OFF 3 TIMER Powe supah r 230Nac SOME 4 o o gt rns 32800 CEZ ODE A rerepot 230Vac 50Hz 5 3 1 Wireless remote control connection for bubble effect IEC female 2 Mains power on off rocker switch 3 Haze remote timer control connection 5 pin DIN 4 Mains inlet IEC male and fuse holder 5 Bubble fluid drain tap Setting up The ORB 400 requires haze fluid
7. not in use for long periods Warning Even if bubble effect is being used without haze effect there may still be hot surfaces on the housing as the haze heater will still be activated 160 462UK User Manual E qtx Remote timer control Timer button latching activates the timer control Continuous button latching overrides timer control for constant haze Manual button non latching overrides timer control for haze on demand Timer indicator illuminated when timer function is active Ready indicator illuminated when heated up ready to produce haze Continuous indicator illuminated when continuous function is active Output control adjusts the amount and density of haze effect k O f 7 7 Interval control adjusts the interval between haze output on timer control L L E r Duration control adjusts the time length of haze output on timer control CONTINUOUS amp MANUAL NG A nI e s9 INTERVAL DURATION DODNDUAWNE a i I I O Cc y S f ley IMER ON OFF When the machine is ready to operate the ready light 5 on the remote timer control will illuminate You may now press the Manual 3 button for haze on demand releasing button stops the haze effect When the ready indicator is off the ORB 400 needs time to re heat and will not produce haze effect For constant haze effect use the latching Continuous 2 button and the Continuous LED 6 will light The density of haze effect c
Download Pdf Manuals
Related Search