X-300 Electric Scooter
Contents
1. X Treme Electric Scooters X 300 Electric Scooter PLEASE BE SAFE WHEN RIDING ALWAYS WEAR AHELMET AND OBEY ALL LAWS Pagel IMPORTANT BATTERY MAINTENANCE CHARGING INSTRUCTIONS You MUST charge completely prior to initial use Follow charging instructions in your Product Handbook Charge immediately after each use Charge before storage You must charge every 30 days if not in use Charge the unit for 6 8 hours or until the light on the charger turns red amp green DO NOT allow this unit to deep discharge the battery For safety purposes DO NOT charge for over 8 hours Turn the unit OFF when not in use Failure to follow these INSTRUCTIONS will VOID YOUR WARRANTY This PRODUCT IS NOT INTENDED FOR EXTREME or OFF ROAD Use Please take care of your scooter DO NOT JUMP or ABUSE THIS PRODUCT DO NOT RIDE IN WET ICY CONDITIONS Failure to follow these instructions will VOID YOUR WARRANTY Page2 IMPORTANT PLEASE READ THIS BEFORE USING THIS PRODUCT READ THIS FIRST WARNING This product does not conform to Federal Motor Vehicle Standards and is not intended for operation on public streets roads or highways Serious injury can result from the unsafe operations of this product Operator can minimize these risks by using certain safety equipment such as safety helmet goggles gloves elbow and kneepads and appropriate footwear DO NOT operate this product2. are done riding the scooter you can fold it down for compact storage and transportation First remove the seat post and seat then using one hand push down on the folding handle while gently pushing down on the handlebars BE CAREFUL NOT TO HIT YOUR HEAD WITH THE HANDLEBAR Push down until you feel the mechanism lock into the down position BRAKING SYSTEM The scooter uses a pinch braking system for the front They are both activated by a hand brake lever on the left and right side of the handlebar Squeezing the hand brake lever with your left hand activates the rear brake Squeezing the hand brake lever with your right hand activates the front brake Make sure to release the HAND THROTTLE GRIP when engaging the brakes Your scooter is equipped with switches on each brake lever that will disengage power to the motor when the brake levers are depressed Practice braking on a smooth dry surface to get used to the feel of the braking system Braking distance is affected by wet conditions and loose and uneven riding surfaces Adjusting the Brakes The Brakes on the scooter should come fully adjusted from the factory However it may be necessary to adjust the brakes from time to time To adjust the front brakes For brakes that are adjusted too loose 1 Adjust the tension screw on the left hand brake lever by rotating counter clockwise until the wheel spins freely For brakes that are adjusted too tight Page9 2 Tighten the tens
3. footplate 3 Locate your Battery Charger Find the charger socket end that has a three prong socket and plug it into the scooter 4 Next plug the AC plug into a wall outlet Charging Indicators RED Charging RED amp GREEN Fully charged and ready for use RIDING 1 sure that all of the exposed bolts and screws are tightened 2 Raise the kickstand to its upright position 3 Push the on off switch located on the left handlebar to the ON position 4 Put one foot on the deck of the scooter while pushing off with the other foot gently rotate the THROTTLE GRIP on the right side of the handlebars The scooter will begin to move on its own power Your scooter has a variable speed hand throttle You can control the speed of your scooter by the amount of pressure you use when rotating the hand throttle The more you rotate the faster you will go STOPPING amp BRAKING 1 To brake release the THROTTLE GRIP and depress the BRAKE LEVERS on the left right side of the handlebars Depressing the brake will disengage power to the motor When the unit feels like it is loosing power or not accelerating to full speed the scooter is ready to be re charged Pages NOTE Ifthe on off switch is left in the ON position for than 10 15 minutes without moving Smart Power will shut itself OFF To reset turn the unit OFF wait a few seconds and then switch it back ON again FOLDING amp STORAGE When you
4. in traffic on wet frozen oily or unpaved surfaces or under the influence of drugs and or alcohol Avoid uneven surfaces potholes surface cracks and obstacles DO NOT use a water hose to clean this product See Product Handbook for more information This product is recommended for riders 14 YEARS OF AGE and older SAFETY Persons without excellent vision balance coordination reflex muscle and bone strength and good decision making capabilities should not use this product Minors without adult supervision should not use this product Persons unwilling or unable to take responsibility for their own actions should not use this product The user of this product assumes ALL risks associated with its use To minimize these RISKS the user must wear safety helmet goggles gloves elbow and kneepads and appropriate footwear This product is ELECTRIC DO NOT ride this product in wet conditions puddles or rainy weather Page3 QUICK REFERENCE SAFETY GUIDE SAFETY GUIDE The recommended minimum age for riding this scooter is 14 years old To avoid damage to the motor and footplate do not overload the scooter Never ride with more than one person Inspect your scooter thoroughly before each use for loose or missing parts Avoid unintentional starts by turning the scooter off while not in use To avoid the risk of a short circuit in the electrical parts do not use your Electric scooter in the rain and never spray o
5. riding position with the throttle on the rider s right side Secure the handlebars to the post by tightening the bolts on the clamp with the enclosed Allen wrench as shown Secure the hand brakes in place by using the provided Allen Wrench to first loosen the tension bolts Adjust the levers to a comfortable position and tighten the bolts BE CAREFUL NOT TO PULL ON THE CABLES Assembly Cont 6 Page7 Check below the foot plate to ensure the motor connector is plugged into the controller If not connect the two ends together as shown Attach the seat post to the seat post receiver then attach the clamp to the top of the seat post Pull the upper seat post to the desired position and tighten the clamp securely Attach the seat to the upper seat post and tighten the seat bolts as shown FAILURE TO PROPERLY TIGHTEN AND ALIGN THE SEAT COULD RESULT IN RIDER INJURY DO NOT ATTEMPT TO RIDE WIHTOUT PROPER SEAT ADJUSTMENT AND ENSURING SEAT BOLTS ARE SECURE amp TIGHT CHARGING Your scooter comes partially charged out of the carton You must charg the unit for 6 8 hours prior to it s first use We also recommend charging your scooter after each use and prior to storage WARNING Do not allow your scooter to go into deep discharge as this will damage the batteries 1 sure unit is turned off 2 Open the charging socket cover located on the right side of the scooter frame under the
6. MAGE THE BEARINGS Page 10 ADJUSTING THE CHAIN The chain will come adjusted from the factory However it may be necessary to adjust the chain from time to time The chain must be well aligned onto the sprockets in order to avoid uneven wear This will result in shortened chain life How tight should the chain be if the chain is skipping or jumping on the sprockets this is too loose and may be harmful the chain is making a humming sound when the wheel is turning this is too tight and may cause the chain to snap The correct tension is achieved by adjusting the chain from its loose position to when it becomes lightly tense To tighten the chains Slightly loosen the two axle bolts on both sides of the rear wheel Fig 14 Then slowly adjust the two adjusting screws on each side of the rear tire Fig 15 until chain reaches the proper tension Rotate the rear wheel to make sure the chain is aligned Finally lock and tighten the rear axle bolts prior to riding Pagel1 MAINTENANCE SCHEDULE Proper care of your scooter will insure optimal performance and longer life span The following are a few maintenance suggestions that will keep your scooter running in top condition Daily Maintenance Perform each time you ride your scooter Clean the exterior of the unit with a soft damp rag DO NOT WASH WITH A HOSE Check that all nuts and bolts are securely tightened Lubricate the chain
7. ion screw on the left hand brake lever by rotating it clockwise until the wheel has a slight drag For Further Front Brake Adjustment 3 Locate the adjustment screw on the front brake assembly located above the front wheel Tighten or loosen as necessary SQUEAKY BRAKES The brakes may squeak before they are broken in This is normal and will not affect the function or performance of the brakes With continued use the squeak should go away TIRE PRESSURE The tire must be inflated to a maximum of 50 P S I It is also recommended to use a tube additive like Slime available from any motorcycle shop to avoid inconvenient punctures Empty all air from the tire prior to loosening the bolt to split the rim MAINTENANCE RECOMMENDED TOOLS To adjust and service the scooter you will need the following tools Allen Wrenches 3 4 5 6 mm Wrenches 10 13 13 mm Open end wrench Large Adjustable Crescent Wrench Philips Head Screwdrivers Oil Grease or Lubricant ADJUSTING THE HEAD UNIT The head unit will come adjusted from the factory However riding on rough terrain and general use may cause the head unit to become loose over time It may be necessary to adjust the head unit from time to time To adjust the head unit 1 Rotate the handle bar as far right as it will go to expose the HEAD UNIT see fig left 2 Using a large adjustable wrench gently turn the BEARING LOCK clockwise to tighten NOT OVER TIGHTEN OR IT WILL DA
8. n 5 PACKAGE CONTENTS ASSEMBLY amp GETTING STARTED 6 RIDING BRAKING 8 FOLDING AND eee eae eens eee eee eas 8 BRAKING SYSTEM amp 9 TIRE PRESSURE 10 MAINTENANG E 10 12 TROUBLESHOOTING GUIDE 12 SUPPOR TINFORMATNON 13 PageS PACKAGE CONTENTS Your scooter comes with the following items in the box Please locate all of the following X 300 Scooter 24V Battery Charger Tool Kit amp User Manual Seat Seat Post amp Clamp GETTING STARTED Please read and understand these instructions and the OPERATING PROCEDURES section prior to starting or riding your scooter 1 2 Page6 Assembly Carefully remove the scooter from the box To unfold the scooter begin by pressing down on the FOLDING HANDLE with one hand while gently pulling up on the handlebars with the other Fully extend the handlebars to their upright position until you feel the mechanism lock into place Attach the handlebars by first loosening the 4 Allen head bolts and removing the top of the handlebar cap Lay the handlebar on top of the handlebar bracket being sure to orient the bars in the correct
9. r wash off your scooter with water Do not place the battery near fire or heat To avoid damage to the battery do not use the charger if it has been damaged in any way Keep hands face feet and hair away from all moving parts Do not touch the motor or wheels while they are rotating Brakes are designed to control speed as well as stop the scooter Practice braking for proper slowing down and smooth stops Maintain your scooter as recommended in this Product Handbook Use only quality replacement parts as recommended by the manufacturer Inspect the entire scooter prior to each use Replace any part that is cracked chipped or damaged before use NEVER ALLOW CHILDREN TO OPERATE THE SCOOTER WITHOUT ADULT SUPERVISION NEVER ATTEMPT TO OPERATE THE SCOOTER WHILE UNDER THE INFLUENCE OF ALCOHOL If a situation arises that is not covered in the manual proceed with caution and use good judgment Page4 DO NOT RETURN TO STORE Do not use this vehicle for the first time until you have inflated the tires to the correct PSI and completely charged the battery Failure to follow these instructions may damage your vehicle and void your warranty CALL TOLL FREE OR GO ONLINE 1 800 772 3852 www x tremescooters com support For General Information or Parts Visit www x tremescooters com TABLE OF CONTENTS IMPORTANT INFORMATION QUICKREF 2 4 TABLE OF CONTENT iscssansraactnctaanareatecpadi
10. with any silicone spray 3 amp 1 oil or any good clean motor oil Check battery charger for any frayed cut wires TROUBLESHOOTING GUIDE SYMPTONS POTENTIAL CAUSE SOLUTION The charger light turns green amp red right away Batteries do not hold a charge Unit does not have specified travel range 1 This indicates the 1 batteries are adequately charged Batteries have reached the end of their useful life Charger is malfunctioning Continue to charge the batteries for 6 8 hours prior to initial use Look for loose or disconnected wire Replace Batteries Replace Charger Unit Unit moves intermittently or very slow Unit will not move when throttle lever is activated Unit stops abruptly during use Loose or broken wire 1 Batteries not fully charged Loose Wire Bad Throttle or controller Batteries not fully charged Brake switches out of adjustment Batteries have reached the end of their useful life Charge or replace batteries Check for loose wires Replace Replace batteries or charger Loosen brakes Replace batteries Check for loose or broken wires and Repair replace Page12 DO NOT RETURN TO STORE IF YOU NEED HELP CALL TOLL FREE OR GO ONLINE 1 800 772 3852 www x tremescooters com support For General Information or Parts Visit www x tremescooters com Page13 Revised 3 30 10
Download Pdf Manuals
Related Search