Untitled - Chinavasion
Contents
1. You can set 2 users User can adjust blue red gain according to existing environment B gain adjust 0 255 R gain adjust 0 255 Back light setting If the scenery is in the environment with strong background light then you can select Back light compensation to carry out back light compensation setting to automatically adjust the brightness of scenery so that the scenery will not be too dark so as to achieve well defined image If the object being shot has very strong light then you can select High light compensation to reduce the exposure rate of the object so as to achieve well defined image Note Brightness compensation is mainly used to constraint the strong light of car lamp at night This function can be set as back light compensation high light compensation The main menu of setting Back Light Compensation is as follow The main menu of setting High Light Compensation is as follow SETUP MENU SETUP MENU LENS Dee SHUTTER AGC MANUALG WHITE BAL ATWA BACKLIGHT BEC PICT ADJUST 4 LENS Dey SHUTTER AGC MANUALY WHITE BAL ATWe BACKLIGHT HEC PICT ADJUST 4 ATR OFF MOTION DET ON ATR OFF MOTION DET ON NEXTd EXITd SAVE AL d NEXTe EXITd SAVE ALLa When the background of the object being shot is very bright this function can be used to com pensate the dulling part of the object being as to achieve correct exposure so that shot resulted from back light so that the fore the ma2. NR o CAMERA ID OFF SYNC INT LANGUAGE ENGLISH CAMERA RESET BACKE EXITd SAVE ALLa The main menu of setting Black White mode is as follow SETUP MENU PRIVACY ONd DAY NIGHT BZW NR d CAMERA ID OFF SYNC INT LANGUAGE ENGLISH CAMERA RESET BACKE EXIT SAVE ALL d Digital Color Camera 12 SETUP NENU You can select auto color or black amp white modes user can set it by himself to satisfy his requirement PRIVACY DAY NIGHT NR AMERA ID Auto mode submenu is shown as follow sh LANGUAGE DAY NIGHT BURST DELAY CNT DAYSNIGHT NIGHT gt DAY BACKS EXIT CAMERA RESET ONd i COLGR OFF INT ENGLISH SAVE Alla Noise Reduction Description of menu functions The main menu of setting Color mode is as follow RETURNS 2D digital noise reduction function it can effectively eliminate video noise points and color noise points Auto mode can be used to switch the ly image at night or in low illumination NRUMODE condition to black amp white mode V LEVEL Burst ON OFF C LEVEL Delay control 0 255 Day Night 0 255 Night Day 0 255 RETURNa The main menu of setting Black White mode is as follow B W BURST RETURNA Burst ON OFF Camera identification code Open the main menu of Camera ID address as follow SETUP MENU PRIVACY ONe DAY NIGHT B Ne NR a CAMERA TD ONE SYNC INT LANGUAGE ENGLISH CAMERA RESET BACKE EXIT SAVE ALLe
3. under the extreme light condition of low illumination so that the picture will be cleaner Enter 2D Noise Reduction menu as follow Adjust the levels of C and Y Noise reduction mode Y C Y C OFF Y Level 0 15 C Level 0 15 The submenu of setting Camera ID address is as follow CAMERA ID CAMERA ABCDEFGHI JKLMNOPQRSTUY WXYZ0123456789 8S28 OF gt 28 F x CAR CHR2 t CLR POS RETURNE User defined ID address CLR POS dear ID Digital Color Camera 13 A eeu OOOO EE Description of menu functions Description of menu functions Synchronization mode internal synchronization Camera reset Power supply synchronization mode more stable in multiple cameras switching When Camera Reset is selected the camera will be restored to factory setting As shown below colorless rolling and AC24V optional As shown below SETUP MENU SETUP MENU ONe COLOR SAVE ALLd Language setting You can set as English Japanese German French Polish Portuguese Spanish and Chinese As shown below SETUP MENU Note Digital Color Camera 14 Digital Color Camera 15
4. AGC MANUALS WHITE BAL ATNA BACKLIGHT OFF PICT ADJUST ATR OFF MOTION DET ON NEXT EXIT SAVE ALLY White balance setting Description of menu functions Select Manual to enter submenu as follow MANUAL SETUP MODE SHUT ASC SHUTTER 1 50 AGC 6 00 RETURNE Mode fixing Shutter AGC Shutter 1 50 1 120 1 250 1 500 1 1000 1 2000 1 4000 1 10000 Automatic Gain 6 00 12 00 18 00 24 00 30 00 36 00 42 00 44 80 White balance setting can be adjusted continuously according to the difference of color temperature of object being shot the white balance will be adjusted automatically according to existing environmental color This function can be set as ATW Push User 1 2 Anti Color Rolling Push Lock and Manual The main menu of ATW mode is as follow SETUP MENU LENS 0Ce SHUTTER AGC MANUAL WHITE BAL ATWA BACKLIGHT OFF PICT ADJUST ATR OFF MOTION DET ONJ NEXT EXIT SAVE ALLY In outdoor environment the color temp erature is between 2500K 9500K which is suitable to use ATW auto tracing white balance mode Select ATW to enter submenu as follow ATW SPEED Tmt 239 DELAY CNT Tf 016 ATH FRANE x1 00 ENVIRONMENT INDOOR RETURNG Speed 0 255 Delay control 0 255 Auto tracing white balance 0 50 1 00 x1 50 x2 00 Environmental options indoor outdoor Digital Color Camera 07 Description of menu functions The main menu of setting ma
5. DC in Lens type as follow Auto DC iris setting speed adjust 0 255 SETUP MENU DC IRIS MODE AUTO SPEED Timm 080 LENS SHUTTER AGC WHITE BAL BACKLIGHT PICT ADJUST ATR MOTION DET RETURNG NEXT EXITA SAVE ALLa Digital Color Camera 05 Description of menu functions Open iris setting speed adjust 0 255 DC IRIS MODE SPEED RETURNA Shutter Automatic Gain Control This function can be set as Manual Auto The main menu of setting auto mode is as follow SETUP MENU LENS Dee SHUTTER AGC AUTOJ WHITE BAL ATWA BACKLIGHT OFF PICT ADJUST 4 ATR OFF MOTION DET ONg NEXTa EXIT SAVE Alla Set the submenu of automatic gain as follow AUTO SETUP HIGH LUMINANCE Mi DC IRIS BRIGHTNESS Mju 024 LOW LUMINANCE MODE AGC BRIGHTNESS x0 50 RETURNE Digital Color Camera 06 Close DC iris DC IRIS MODE SPEED RETURNA Select Auto Jto enter submenu as follow Adjust shutter to control exposure time so as to improve image quality Brightness adjust 0 255 AUTO SETUP HIGH LUMINANCE MODE SHUT DE IRIS BRIGHTNESS fu 024 LOW LUMINANCE MODE OFF BRIGHTNESS 0 50 RETURN When the light is dark adjust gain value to affect the brightness of image The higher the gain value the brighter the image brightness Brightness x0 25 x0 5 x0 75 x100 The main menu of setting manual mode is as follow SETUP MENU LENS Dea SHUTTER
6. Digital Color Video Camera Operating Instruction Thank you for the purchase of the product of our company in order to obtain optimum effect please read all instructions on this manual carefully before using and keeps this manual properly for reference CAUTION AN Electric shock hazard ARS Do not open Note in order to avoid electric shock hazard please never remove the protective or back cover of the machine There is no maintainable part inside the machine The repair work should only be carried out by qualified personnel This symbol indicates that uninsulated voltage may exist inside the casing and there is potential risk of electric shock if it is not avoided then low grade or mod erate injure may be resulted which is also a prompt to user for unsafe operation AN This symbol prompts you to pay attention to the important operation and maintenance instruction in attached information Waming In order to prevent damage result from fire or electric shock etc never expose the product in water or humid place This equipment will generate or utilize the energy of radio frequency if correct methods of installation and application are not adopted that is the requirements of this manual are not followed strictly then radio communication will be harmfully interfered Warning 1 In order to avoid incident of electric shock please never use power supply other than stipulation 2 Never place or i
7. chine can shoot well defined car ground will be brighter license plate This function is mainly used to screen the lighting of head lamp of vehicle so Digital Color Camera 09 Description of menu functions Image adjustment You can make adjustment through the following options Mirror Brightness Contrast Sharpness Hue Gain Enter image adjusting submenu as follow PICT ADJUST 4e Mirror adjust ON OFF horizontal adjust Se Brightness adjust 0 255 erie Contrast adjust 0 255 GAIN mee Sharpness adjust 0 255 Hue adjust 0 255 Gain adjust 0 255 color saturation adjust MIRROR RETURNE Adaptive Tone scale Repetition In the scenery area being shot carry out automatic brightening compensation to dulling part so that the whole picture will be more clear and bright Enter Adaptive Tone scale Repetition submenu as follow Open the main menu of Adaptive Tone scale Repetition as follow SETUP MENU ATR LENS DCH SHUTTER AGC MANUA WHITE BAL ATMA BACKLIGHT OFF PICT ADJUST d ATR ONE MOTION DET ONd EUMINANCE MID CONTRAST WID RETURNA NEXTd JEXTTd SAVE ALLA Luminance itan low middie Digital Color Camera 10 Description of menu functions Motion detection setting When the range of video obtained by camera is abnormal a trigger signal will be output as an alarm and switch Open the main menu of Motion Detection as fo
8. dded with fan or heating device Repair and failure description 1 Disconnect the power supply of camera and have the equipment repaired by qualified maintenance personnel under the following conditions a If power cable or plug is damaged b If the camera is wetted by rain or water c If liquid splashes into camera or object drops into camera d If you do not carry out conventional operation to the camera according to the operation instruction note that only the control mechanism involved in the operation instruction can be adjusted because if incorrect adjustment is carried out to other control mechanism then the equipment may be damaged and it can be restored to normal state only through further repair by qualified technical personnel e If the camera drops to the ground or the casing is damaged f If the camera has obvious variation in performance 2 During the process of operation if abnormal phenomenon abnormal sound smell or smoke or failure no image etc occurs please immediately stop the using of camera and power off then contact the nearest distributor or the supplier of the area 3 Please don t dismantle or modify this product by any method Any variation or modification activity unauthorized by the manufacturer will result in canceling the right of user to operate the equipment The problem caused by unauthorized dismantle or repair by user is not covered by guarantee 4 If there is very bright area on object
9. f introduction Description of menu functions Technical parameters Type PAL NTSC Imaging device 1 3 Sony Super HAD CCD II Effective pixel 512x582 510x492 Horizontal definition 480 TVL Synchronization system Internal Automatic exposure DC Manual Automatic white balance ATW PUSH USER MANUAL Automatic gain control Yes Gamma correction 0 45 Video signal to noise ratio More than 52dB Lowest illumination 0 05 Lux F1 2 Back light compensation BLC HLC OFF default OFF Shutter control Yes Day night mode Color BW Auto Switch Mirror image OFF Menu Yes Hidden screening 4 zone Motion detection 24x16 blocks Video output Composite 1 Vp p 75 Ohms Power supply input DC 12V 10 Power consumption 120MA 5 Working temperature 20C 60C Working humidity 80 RH Digital Color Camera 04 Main menu is as follow SETUP MENU SETUP MENU LENS MANUAL PRIVACY OFF SHUTTER AGC AUTOd DAY NIGHT AUTOd WH ATWa NR BACKL OFF CAMERA ID OFF PICT ADJUST 4 SYNC INT T OFF LANGUAGE ENGLISH MOTION DET ONG CAMERA RESET NEXT BACKE EXITd SAVE ALLd EXIT SAVE ALLd Lens You can select Manual Auto lens Select Manual in Lens type as follow SETUP MENU LENS MANUAL SHUTTER AGC AUTOW WHITE BAL BACKLIGHT PICT ADJUST ATR MOTION DET NEXTd EXITd SAVE ALLd Select DC Lens to enter submenu as follow Select
10. hing You can select auto color or black amp white modes user can set it by himself to satisfy his requirement Color rolling constraint When camera is used under fluorescent lamp this function can be used to eliminate circular rolling phenomenon of color from white to blue pink and then to white again so as to achieve more stable picture Back Light Compensation BLC When the background of the object being shot is very bright this function can be used to compensate the dulling part of the object being shot resulted from back light so that the foreground will be brighter Privacy area screening Up to 4 screening areas can be set at the same time the area range and position can be adjusted the color and transparency of screening area can be adjusted mosaic function Motion detection When the range of video obtained by camera is abnormal a trigger signal will be output as an alarm and switch OSD menu You can set as English Japanese German French Polish Portuguese Spanish and Chinese Digital Color Camera 01 Brief introduction Technical parameters Type Imaging device PAL NTSC 1 3 Exview HAD CCDII Brief introduction Effective pixel 976x582 976x494 Horizontal definition 650 TVL Synchronization system Internal Automatic exposure DC Manual Automatic white balance ATW PUSH USER MANUAL Automatic gain control Yes Gamma correction 0 45 Video signal to
11. llow SETUP MENU LENS SHUTTER AGC WHITE BAL BACKLIGHT PICT ADJUST ATI MOTION DET Set Motion Detection submenu as follow MOTION DET DETECT SENSE mmmmmje 111 BLOCK DISP ON MONITOR AREA ON AREA SEL 1 4 TOP p 000 BOTTOM puuna 000 LEFT pe 000 RIGHT poin 000 RETURNA NEXTe apart SAVE ALLd Detection sensitivity 0 127 Block display ON OFF Monitor area ON OFF Area select up to 4 areas can be set Top 0 288 Bottom 0 288 Privacy area screening Left 0 468 Right 0 468 You can set to hide part area Up to 4 screening areas can be set at the same time the area range and position can be adjusted the color and transparency of screening area can be adjusted mosaic function Set Privacy area screening submenu Open the main menu of Privacy area as follow screening as follow SETUP MENU PRIVACY PRIVACY ONe AREA SEL 1 4 DAY NIGHT AUTOd TOP ji 000 NR d BOTTOM hm 000 CAMERA ID OFF LEFT im 000 SYNC INT RIGHT fom 000 LANGUAGE ENGLISH COLOR 1 CAMERA RESET TRANSP 1 00 MOSAIC OFF RETURNG BACKE EXITe SAVE ALLd Area select up to 4 areas can be set Top 0 268 Bottom 0 288 Lett 0 468 Flight O GEE Color 1 8 Transparency of screening 0 5 0 75 1 00 Mosaic ON OFF Digital Color Camera 11 0 a a a Description of menu functions Day Night mode Set auto mode as follow SETUP MENU PRIVACY ONe DAYZNIGHT AUTOS
12. noise ratio More than 52dB Lowest illumination 0 05 Lux F1 2 Back light compensation BLC HLC OFF default OFF Shutter control Yes Day night mode Color BW Auto Switch Mirror image OFF Menu Yes Hidden screening 4 zone Motion detection 24x16 blocks Video output Composite 1 Vp p 75 Ohms Power supply input DC 12V 10 Power consumption 120MA 5 Working temperature 20C 60C Working humidity 80 RH Digital Color Camera 02 Technical parameters Imaging device Effective pixel Horizontal definition Synchronization system 1 3 Sony Super HAD CCD II 752x582 768x492 Internal Automatic exposure DC Manual q Automatic gain control Automatic white balance ATW PUSH USER MANUAL Yes Gamma correction 0 45 Video signal to noise ratio More than 52dB Lowest illumination 0 05 Lux F1 2 Back light compensation BLC HLC OFF Een ry Shutter control Yes Day night mode T Color BW Auto Switch Mirror image OFF Menu Yes Hidden screening E 4 zone i Motion detection 24x16 blocks Video output Composite 1 Vp p 75 Ohms Power supply input DC 12V 10 Power consumption SE 120MA 5 Working temperature 20C 60C Working humidity 80 RH Digital Color Camera 03 Brie
13. nstall the camera on unstable place support tripod bracket or platform Otherwise serious personnel hurt or equipment damage may be resulted 3 When cleaning is carried out power off firstly then use a dry soft cloth to wipe off the dirt on camera if it is very dirty then use furniture cleaner to remove the dirt Never drop water on the component of the product Otherwise electric shock or fire may be resulted 4 Never install this device at humid dusty or smoky place otherwise electric shock or fire may be resulted Never place conductor such as screwdriver iron wire or metal or container filled with water on the camera Precautions 1 Never drop the camera on ground or subject to intense impact and vibration away from intense vibration and place with electromagnetic interference 2 Never install the equipment in too warm or too cold environment the recommended using temperature is between 5 C and 60 C 3 If it is required to move the installed product please power off before moving and reinstallation 4 Prevent the camera from direct sun light otherwise CCD may be damaged 5 Install the equipment at ventilated place and prevent hot source 6 When the camera is installed outdoors because of temperature difference between indoor and outdoor moisture may appear inside camera Therefore we recommend you to install the camera indoors When it is necessary to install the camera outdoors please use camera embe
14. nual mode is as follow SETUP MENU LENS OCe SHUTTER AGC MANUALA WHITE BAL MANUALE BACKLIGHT OFF PICT ADJUST 4 ATR OFF MOTION DET ONg NEXT EXIT SAVE ALLd The main menu of setting Anti Color Rolling mode is as follow SETUP MENU LENS DCe SHUTTER AGC MANUALY WHITE BAL ANTE CR BACKLIGHT OFF PICT ADJUST 4 ATR OFF MOTION DET ONg NEXTe EXITO SAVE ALLa The main menu of setting Push Lock is as follow SETUP MENU LENS Dea SHUTTER AGC MANUALU WHITE BAL PUSH EOCK BACKLIGHT OFF PICT ADJUST 4 ATR OFF MOTION DET ONd NEXTe EXITU SAVE ALLa Digital Color Camera 08 Select Manual to enter submenu as follow MANUAL WB LEVEL RETURNe Level 30 93 When camera is used under fluorescent lamp this function can be used to eliminate circular rolling phenomenon of color from white to blue pink and then to white again so as to achieve more stable picture The main menu of setting Push is as follow SETUP MENU LENS Dea SHUTTER AGC MANUAL WHITE BAL PUSH BACKLIGHT OFF PICT ADJUST 4 ATR OFF MOTION DET ONd NEXT ERITA SAVE ALL Description of menu functions The main menu of setting User Customize Select User 1 2 to enter submenu is as follow as follow SETUP MENU USERI WB LENS Dea B GAIN Ti 030 SHUTTER AGC MANUAL R GAIN Tp 033 WHITE BAL USER1d BACKLIGHT OFF PICT ADJUST 4 ATR OFF MOTION DET ON RETURNA NEXT EXIT SAVE ALL
15. then vertical or horizontal bright line will appear on the screen This is called flare which is a common phenomenon occurred in solid camera tube very often it is not a failure Contents Brief introduction Product properties a ameeaumE RnR mH 01 Technical parameters PEENTE SE 02 Description of menu functions Shutter Automatic Gain Control White balance setting Backlight setting Image adjustment Adaptive Tone scale Repetition Motion detection setting Privacy area screening Day night mode Noise Reduction Camera identification code Synchronization mode intemal synchronization Language setting Camera reset EEEE E ENEE 15 Brief introduction Product properties High definition Adopt 1 3 SONY Exview HAD II 960H CCD which has colored 650 lines black amp white 700 lines high definition high sensitivity picture quality High Light Constraint HLC This function is mainly used to screen the lighting of head lamp of vehicle so as to achieve correct exposure so that the machine can shoot well defined car license plate Adaptive Tone scale Repetition ATR In the scenery area being shot carry out automatic brightening compensation to dulling part so that the whole picture will be more clear and bright Noise Reduction NR 2D digital noise reduction function it can effectively eliminate video noise points and color noise points so that the picture will be cleaner Day Night switc
Download Pdf Manuals
Related Search