User Manual - Dallas Avionics
Contents
1. User s Manual wit Black Opal Xtreme Models SS DYNE Flat Panel Display Systems TECHNOLOGIES e Selecting Colourisation presents the menu items TRUE for true colour input MONO for monochrome input or colour input RAINBOW 1 for pseudo colourisation based on spectral rainbow version 1 RAINBOW 2 for pseudo colourisation based on spectral rainbow version 2 and IRONBOW for pseudo colourisation based on the colour temperature spectrum of iron Select the desired item and press ENTER RAINBOW 1 RAINBOW 2 and IRONBOW will access the Pseudo menu The Pseudo menu offers TRUE for unmodified pseudo colourisation INVERT for inverted pseudo colourisation THRESHOLD to enable a temperature grey scale threshold above which pseudo colourisation is applied and ADJUST for setting the threshold to be enabled by THRESHOLD Select the desired item and press ENTER NOTE pseudo colourisation can be applied in a screen lay outs where video any video is displayed and will be applied to all video windows in the lay out NOTE all pseudo colourisation is effected by the use of OVERDRIVE whiter than white which will skew the temperature colour correlations NOTE the MONO option is used to generate 256 grey scales for both colour and monochrome 6 4 5 5 Defaults Menu Vv Defaults menu J Current Reboot Standby Figure 6 7 Defaults Menu Structure e Selecting the Defaults menu presents the men2. Flat Panel Display Systems TECHNOLOGIES AN b User Mode In this mode the previously set button backlight level using up down PRIOR to pressing the On Off button selects the mode and intensity for the main backlight The 3 highest settings for the button backlight select DAY mode 100 50 10 while the lower button backlight settings select NIGHT mode in main backlight default setting decreasing with button backlight setting This user adjustable setting is permanent and will be used on all subsequent power ups unless otherwise changed c Fixed Mode In this mode the default backlight mode and level will be specified and set to suit a particular program requirement d Ramp up Mode In this mode the backlight slowly ramps up through NIGHT and then DAY modes and stops rising when any button is pressed If no button is pressed then DAY mode at maximum brightness is selected 6 4 1 2 The Boot up Sequence The boot up sequence has several phases all of which can be customized to suit customer requirements The first phase is the initial backlight setting There are several options for this one of which is pre configured to suit customer requirements including a slow ramp up of backlight intensity which is suspended by a button press or a specific level and mode i e day or night modes Unless otherwise specified the backlight will be set to DAY mode and at a suitable brightness for visibility under most conditio
3. 6 5 VGA Menu Structure 6 10 Figure 6 6 Settings Menu Structure 6 11 Figure 6 7 Defaults Menu Structure 6 12 File UM RMU M 2296 D_1 Copyright All Rights Reserved Laserdyne Pty Ltd Author s MW TW Authorised TW Rev Date 14 2 14 Page iv User s Manual e 2 Black Opal Xtreme Models AS DYNE Flat Panel Display Systems TECHNOLOGIES 1 INTRODUCTION 1 1 Scope This User s Manual is designed for the operator of the Black Opal Xtreme display models It contains set up operating and user level faultfinding and maintenance information 1 2 Document Structure This manual is structured to take the reader through safety observations system description and specifications to the set up operation and general maintenance of the Black Opal Xtreme There is no separate maintenance document for the Black Opal Xtreme relevant maintenance information is contained in this User s Manual Some diagrams may be made available to the original purchaser of the Black Opal Xtreme depending upon the level of maintenance undertaken by the user File UM RMU M 2296 D_1 Copyright All Rights Reserved Laserdyne Pty Ltd Author s MW TW Authorised TW Rev Date 14 2 14 Page 1 1 User s Manual Ses WW Black Opal Xtreme Models aS DYNE Flat Panel Display Systems TECHNOLOGIES 2 SAFETY 2 1 Electrical Safety The Black Opal Xtreme is designed to operate from low voltage dc power Once i
4. Adjust Button Functions The following sections describe the use of the scroll adjust buttons to adjust the non menu parameter associated with a primary button function 6 4 3 1 Adjust Image Enhancement e Press ENH to enable image enhancement e Use scroll adjust buttons now labelled ENH to select desired enhancement window size will default to that last selected NOTE window size has an effect on enhancement as only the portion of the image contained in the window is sampled A smaller window can yield a more profound result if it contains a narrower spread of native contrasts than a larger one NOTE If zoom is selected on an enhanced image the enhancement parameters are held constant 6 4 3 2 Adjust Digital Zoom The unit multiple digital zoom settings When the unit is turned on the zoom defaults to the lowest available setting e Press ZOOM to enable the scroll adjust buttons for digital zoom adjustment e Use scroll adjust buttons now labelled ZOOM to select desired zoom setting 6 4 4 Reset The system may be reset by holding down the power button for at least 8s CAUTION resetting the system should not be performed gratuitously as the system may not have updated its EEPROM settings since the last setting change File UM RMU M 2296 D_1 Copyright All Rights Reserved Laserdyne Pty Ltd Author s MW TW Authorised TW Rev Date 14 2 14 Page 6 6 User s Manual Black Opal Xtreme
5. Opal Xtreme are presented in a separate Specifications amp Set up document provided with your unit CAUTION ensure that all instructions in the separate Specifications and Set up document applicable to your model are performed correctly before attempting to operate the Black Opal Xtreme File UM RMU M 2296 D_1 Copyright All Rights Reserved Laserdyne Pty Ltd Author s MW TW Authorised TW Rev Date 14 2 14 Page 5 1 User s Manual PA 2 Black Opal Xtreme Models EMS DYNE Flat Panel Display Systems TECHNOLOGIES 6 OPERATION 6 1 Controls The display has 9 points of control model dependent being a horizontal array of function and up down buttons located on the bottom of the front face of the unit and an on off button and a day night button located elsewhere on the front face these are momentary one result per press sealed backlit buttons A typical configuration is shown below In all cases there are 5 Function Buttons and up down buttons The functions of the five Function Buttons vary depending upon the screen being displayed and the level of customisation in the system software In every case the available button function is displayed beside the button on the LCD The up down buttons are available whenever a setting can be varied over a range Such settings include backlight intensity display settings and digital zoom settings Up down buttons are generally referred to as scroll adju
6. Video Menu Structure e Selecting the Video menu presents the menu items GAIN LEVEL SATURATION File UM RMU M 2296 D_1 Copyright All Rights Reserved Laserdyne Pty Ltd Author s MW TW Authorised TW Rev Date 14 2 14 Page 6 9 User s Manual L Black Opal Xtreme Models EMS DYNE Flat Panel Display Systems TECHNOLOGIES Menu Item Result 1 Gain Allows the adjustment of gain value for display contrast 2 Level Allows the adjustment of offset value for display brightness as opposed to backlight intensity 3 Saturation Allows the adjustment of colour intensity similar to the colour feature on a TV e Select the desired item and press ENTER e Inthe case of GAIN LEVEL or SATURATION adjust value and press ENTER 6 4 5 3 VGA Menu The VGA Component Menu is accessed via a Main menu when the current screen lay out has VGA PC input or Component YPrPb Vv VGA menu Gain Offset Phase Figure 6 5 VGA Menu Structure e Selecting the VGA menu presents the menu items GAIN OFFSET PHASE and POSITION and if the VGA menu was accessed from a full screen VGA lay out with no PIP i e accessed via the MENU button DEFAULTS Menu Item Result 1 Gain Allows the adjustment of gain value for display contrast 2 Offset Allows the adjustment of offset value for display brightness as opposed to backlight intensity Allows the adjustment and sett
7. in its original packaging provided that packing and handling conditions described in this manual are observed The packaged unit should not be stored in damp conditions or damage to the packaging will result The unpackaged unit should not be stored in areas where conditions may exceed the product s environmental specification 3 4 Transportation All items should be packed as described in this manual Road rail or air transport are suitable transport methods File UM RMU M 2296 D_1 Copyright All Rights Reserved Laserdyne Pty Ltd Author s MW TW Authorised TW Rev Date 14 2 14 Page 3 1 User s Manual Black Opal Xtreme Models EMS DYNE Flat Panel Display Systems TECHNOLOGIES 4 SYSTEM DESCRIPTION 4 1 General Purpose The Black Opal Xtreme models have been engineered for a wide range of land sea or air borne display applications including remote indirect viewing of video images generated by day night or thermal cameras 4 2 General Description 4 2 1 General Each Black Opal Xtreme model consists of a LCD a microprocessor unit computer and power amp control electronics Each model features MultiVision allowing for multiple analogue and digital inputs and providing simultaneous display of multiple inputs model and connector dependent see specifications All items are housed within a rugged enclosure containing heating and cooling mechanisms The LCD is protected by a t
8. too low a allow unit to warm up no display No image a connected video or graphics a check operation amp source not operating sending specifications of connected signal source b connector dirty or faulty b check clean adjust connector Controls do not a selected at inappropriate a check operating respond point in menu structure instructions b faulty buttons b service required return for diagnosis repair Image lacks contrast a settings inappropriate a adjust settings brightness and colour quality a Backlight setting at minimum a adjust Backlight setting 7 Screen lay outs a Input video format is not a adjust input video corrupt imagery correct for the loaded layout garbled b after turn on press and hold all buttons 1 to 5 simultaneously for 10s release and wait for unit to auto power down approx 30s wait 5s then restart 1 e g pixels out of place lines convoluted menus illegible File UM RMU M 2296 D_1 Copyright All Rights Reserved Laserdyne Pty Ltd Author s MW TW Authorised TW Rev Date 14 2 14 Page A 1 User s Manual e 2 Black Opal Xtreme Models AS DYNE Flat Panel Display Systems TECHNOLOGIES APPENDIX B SET UP MENUS The Xtreme display has two menu structures the User s menu structure and the Set up menu structure The User s menu structure is described in the body of this User s Manual It allows the operator to perform basic correcti
9. 1 2 The Boot up Sequence 6 4 6 4 1 3 Bypassing the Boot up Sequence 6 4 6 4 2 Primary Button Functions 6 5 6 4 3 Scroll Adjust Button Functions 6 6 6 4 3 1 Adjust Image Enhancement 6 6 6 4 3 2 Adjust Digital Zoom 6 6 File UM RMU M 2296 D_1 Copyright All Rights Reserved Laserdyne Pty Ltd Author s MW TW Authorised TW Rev Date 14 2 14 Page iii User s Manual lb Black Opal Xtreme Models EMS DYNE Flat Panel Display Systems TECHNOLOGIES 6 4 4 Reset 6 6 6 4 5 Menus 6 7 6 4 5 1 Main Menu 6 7 6 4 5 2 Video Menu 6 9 6 4 5 3 VGA Menu 6 10 6 4 5 4 Settings Menu 6 11 6 4 5 5 Defaults Menu 6 12 6 4 5 6 MemorEyes Menu 6 13 6 4 6 Working with Menus How to 6 13 6 4 6 1 For Video 6 14 6 4 6 1 1 Adjust Contrast Brightness and or Colour Saturation 14 6 4 6 1 2 Select Colour Option for Display 6 14 6 4 6 2 For VGA 6 14 6 4 6 2 1 Correct Native VGA Image for Contrast Brightness and or Phase 6 14 6 4 6 3 Restore Set up Defaults 6 15 6 4 6 4 Reboot the System 6 15 6 4 6 5 Set the System to Standby 6 15 6 4 7 Shut Down 6 15 6 5 Special Functions amp Modes 6 15 7 GENERAL MAINTENANCE 7 1 7 1 General Cleaning and Care 7 1 7 2 Replacing Desiccant 7 1 APPENDICES A Faultfinding Guide A 1 B Set up Menus B 1 LIST OF FIGURES Figure 6 1 Controls and Indicators typical 6 1 Figure 6 2 Main Menu Structure 6 7 Figure 6 3 Main Menu Maximum Entries Structure 6 8 Figure 6 4 SD Video Menu Structure 6 9 Figure
10. All Rights Reserved Laserdyne Pty Ltd Author s MW TW Authorised TW Rev Date 14 2 14 Page 6 7 User s Manual Ae Zt Black Opal Xtreme Models EMS DYNE Flat Panel Display Systems TECHNOLOGIES SD1 SD2 SD3 SD4 VGA Component SDI SBC Settings Defaults Memoreyes DVR Figure 6 3 Main Menu Maximum Entries Structure e g all inputs generic names e Pressing MENU accesses the appropriate Main menu Menu Item Result SD1 SD2 SD3 Variable option Accesses Video menu to allow adjustment of display characteristics for the SD channel in the current lay out if enabled Applies to main screen or PIP Alternate names can be set to each channel factory setting to allow the physical channel to be named after the source i e CAMERA1 Thermal Rear PIP VGA Component Variable option Accesses VGA Component menu to allow adjustment of display characteristics for RGB or YPrPb inputs in current lay out if enabled Applies to main screen or PIP Alternate names can be set to each channel factory setting to allow the physical channel to be named after the source i e MAP PC HD Variable option Accesses Video menu to allow adjustment of display characteristics for the selected SDI channel s in current lay out if enabled Applies to main screen or PIP Alternate names can be set to each channel factory setting to allow the physical channel to be named after the source i e CAME
11. Models AS DYNE Flat Panel Display Systems TECHNOLOGIES 6 4 5 Menus There are two menu structures the User s menu structure and the Set up menu structure The Set up menu structure is not used in normal operation It is only available when a special sequence is performed It allows basic and advanced set up of inputs outputs corrections and adjustments The settings selected in the Set up menu structure become the default settings for parameters in the User s menu structure The Set up menu structure is described in an appendix to this User s Manual The User s menu structure is available during normal viewing and use It allows the operator to perform basic corrections and adjustments effecting the appearance of the display Settings made under the User s menu structure can be optionally retained until the next change even during shut down and start up The user can at any time return all parameters to the default settings selected under the Set up menu structure The ability for the system to retain the settings can be factory enabled 6 4 5 1 Main Menu The contents of the Main menu will depend on the features enabled for the current layout i e which input channels are shown on screen for the current layout The Some variants of the Main menus are shown in the following diagrams Layout specific options Standard options Figure 6 2 Main Menu General Structure File UM RMU M 2296 D_1 Copyright
12. RA1 Thermal Rear PIP HD SDI File UM RMU M 2296 D_1 Copyright All Rights Reserved Laserdyne Pty Ltd Author s MW TW Authorised TW Rev Date 14 2 14 Page 6 8 User s Manual Si y Black Opal Xtreme Models SS DYNE Flat Panel Display Systems TECHNOLOGIES er m option Accesses Video menu to allow adjustment of display characteristics for the SBC single board computer channel in current lay out if installed Applies to main screen or PIP Alternate names can be set to each channel factory setting to allow the physical channel to be named after the source i e DVR SETTINGS Standard option Accesses Settings menu for display wide settings such as colourisation DEFAULTS Standard option Accesses Defaults menu for restoration of Set up defaults to screen layout s and allows the system to be rebooted or set to standby 7 Memoreyes DVR Variable option Changes button 1 5 functions to allow access to external recorder functions e Select the desired item and press ENTER 6 4 5 2 Video Menu variable between layouts The SD1 SD2 SD3 SD4 Menu is accessed via a Main menu when the current screen lay out contains a full screen video channel Note that if the system is configured to also operate a Memoreyes DVR then an additional menu option for the control of the recorder will also appear Vv SDn menu J Gain Level Saturation Figure 6 4 SD
13. User s Manual a 2 Black Opal Xtreme Models ERS DYNE Flat Panel Display Systems TECHNOLOGIES User s Manual READ THIS DOCUMENT THOROUGHLY BEFORE ATTEMPTING TO ASSEMBLE OR OPERATE Black Opal Xtreme Flat Panel Display Systems Treatment of this product other than as specified herein may result in damage to the product or attached systems invalidation of the warranty The location of this document should always be known to all users of and technical support personnel for the Black Opal Xtreme The information contained herein is proprietary to Laserdyne Pty Ltd No part of this work may be reproduced or copied in any way without prior written permission of Laserdyne Pty Ltd Note specifications herein are subject to change without notice CAUTIONS e On receipt of your Black Opal Xtreme immediately report any damage to packaging or contents to your supplier e Ensure that all instructions in the separate Specifications and Set up document applicable to your model are performed correctly before attempting to operate the Black Opal Xtreme e The system is in standby status whenever external power is applied Do not leave the system in standby status for extended periods remove external power e Resetting the system should not be performed gratuitously as the system may not have updated its EEPROM settings since the last setting change e Avoid scratching abrading or contaminating the surface of the display wi
14. button label 6 4 Operating Procedures CAUTION the system is in standby status whenever external power is applied Do not leave the system in standby status for extended periods remove external power 6 4 1 Start up 6 4 1 1 Starting Up e Before proceeding check that all connections and mountings are secure and appropriate then switch on external power to the display e Select a suitable button backlight intensity by pressing up down PRIOR to pressing the On Off button e Press the On Off button to power up the system NOTE The default backlight mode and level used on power up can be controlled in a number of ways depending on the factory configured power up configuration as follows e f the Day Night button is held down when the On Off button is pressed then NIGHT mode is enabled for this power up regardless of any factory configured boot mode e Otherwise pressing the power button will select one of the 4 factory configured backlight modes as follows a Auto mode In this mode the light sensor on the front of the display is used to determine the correct mode If the detected light level is below a threshold then NIGHT mode is selected otherwise DAY mode is selected In both cases the level is set to 50 File UM RMU M 2296 D_1 Copyright All Rights Reserved Laserdyne Pty Ltd Author s MW TW Authorised TW Rev Date 14 2 14 Page 6 3 User s Manual hl 7 Black Opal Xtreme Models SS DYNE
15. e On Off button for approx 2 seconds to set the unit to standby e Switch off external power to the unit 6 5 Special Functions amp Modes Special functions are optionally available to the user accessed during the boot up sequence They are Boot Sequence Customisation where the initial backlight level and the presentation of the boot logo and of version data may be altered EEPROM Recovery to be used in the case where lay outs have become corrupted and File UM RMU M 2296 D_1 Copyright All Rights Reserved Laserdyne Pty Ltd Author s MW TW Authorised TW Rev Date 14 2 14 Page 6 15 User s Manual woth Black Opal Xtreme Models AS DYNE Flat Panel Display Systems TECHNOLOGIES Demo Mode which runs a sequence of patterns and features for test purposes and for when an automatic demonstration of system features is desired Other required customizations Information about accessing these will be provided if the features are enabled File UM RMU M 2296 D_1 Copyright All Rights Reserved Laserdyne Pty Ltd Author s MW TW Authorised TW Rev Date 14 2 14 Page 6 16 User s Manual Black Opal Xtreme Models AS DYNE Flat Panel Display Systems TECHNOLOGIES 7 GENERAL MAINTENANCE 7 1 General Cleaning and Care The following procedures are those that may be performed by the User Other than the following procedures maintenance is to be performed o
16. essing EXIT will abandon any in progress adjustments i e adjustments that have not yet been set by pressing ENTER File UM RMU M 2296 D_1 Copyright All Rights Reserved Laserdyne Pty Ltd Author s MW TW Authorised TW Rev Date 14 2 14 Page 6 13 User s Manual hl Black Opal Xtreme Models EA DYNE Flat Panel Display Systems z TECHNOLOGIES AN 6 4 6 1 For Video e If a Main menu is offered select VIDEO MAIN or VIDEO PIP in the case of full screen video only the Video menu will be offered directly upon pressing MENU button 6 4 6 1 1 Adjust Contrast Brightness and or Colour Saturation e From the Video menu select GAIN to adjust display contrast LEVEL to adjust display brightness as opposed to backlight intensity or SATURATION to adjust colour intensity as required e Set value s as required 6 4 6 1 2 Select Colour Options for Display e From the Settings menu select Colourisation e From the Settings Colourisation menu select TRUE to display the true input colour or MONO GREY to display 8 bit grey scale or e From the Settings Colour menu select RAINBOW 1 for pseudo colourisation based on spectral rainbow version 1 RAINBOW 2 for pseudo colourisation based on spectral rainbow version 2 or IRONBOW for pseudo colourisation based on the colour temperature spectrum of iron The Pseudo menu will be offered e f a pseudo colourisation item has been selected from the Settings Co
17. ghting and security systems including Image Enhancement video inputs are compensated for obscuration e g rain fog snow mist or smoke within an adjustable central window where contrast and colour are enhanced For a chosen window size the enhancement is applied to that portion of the displayed image Digital Zoom a fully X 8 Y interpolated smart zoom not merely pixel multiplying yields a clear zoomed image without the blocky pixelated appearance often seen with digital zooming and Freeze Frame freezes the current prime video channel while leaving live any video inset Colourisation applies preloaded colour palettes to monochrome imagery Motion edge tearing compensation minimises the jagged edges that can occur with motion in video on LCDs 4 3 System Contents The Black Opal Xtreme system consists of 1 x Black Opal Xtreme unit 1 x User s Manual and 1 x Specification and Set up document plus any options that the purchaser has elected to acquire NOTE the purchaser must supply the appropriate Power Video and VGA Cable Assemblies File UM RMU M 2296 D_1 Copyright All Rights Reserved Laserdyne Pty Ltd Author s MW TW Authorised TW Rev Date 14 2 14 Page 4 2 User s Manual ab 2 Black Opal Xtreme Models EMS DYNE Flat Panel Display Systems TECHNOLOGIES 5 SYSTEM SPECIFICATIONS amp SET UP The specifications and set up procedures for your model of Black
18. ing of phase value e Select the desired item and press ENTER e Inthe case of GAIN OFFSET or PHASE adjust value and press ENTER File UM RMU M 2296 D_1 Copyright All Rights Reserved Laserdyne Pty Ltd Author s MW TW Authorised TW Rev Date 14 2 14 Page 6 10 User s Manual wie Black Opal Xtreme Models ES DYNE Flat Panel Display Systems TECHNOLOGIES NOTE the VGA GAIN and OFFSET adjustments work differently to those for video The two are inter related and change inversely to the value change i e increased value yields decreased effect The SDI Menu does not have any options The SBC Menu does not have any options 6 4 5 4 Settings Menu e Selecting the Settings menu presents the menu items COLOUR Vv Settings menu Colourisation BLU NVIS Defaults mn igure 6 6 Settings Menu Structure Menu Item Result Colourisation selection of the colourisation to be applied to the entire window Accesses the BLU menu to allow adjustment of the backlight level upon start up Selectable between Day and Night Accesses the NVIS menu to allow adjustment of the Night backlight colour Selectable between Green 4 Defaults Accesses Defaults menu e Select the desired item and press ENTER File UM RMU M 2296 D_1 Copyright All Rights Reserved Laserdyne Pty Ltd Author s MW TW Authorised TW Rev Date 14 2 14 Page 6 11
19. lour menu RAINBOW 1 RAINBOW 2 or IRONBOW then from the Pseudo menu select TRUE for unmodified pseudo colourisation INVERT for inverted pseudo colourisation THRESHOLD to enable a temperature grey scale threshold above which pseudo colourisation is applied or ADJUST for setting the threshold to be enabled by THRESHOLD Select the desired item and press ENTER 6 4 6 2 For VGA 6 4 6 2 1 Correct Native VGA Image for Contrast Brightness and or Phase e From the VGA menu select GAIN to adjust display contrast OFFSET to adjust display brightness as opposed to backlight intensity or PHASE as required e Set value s as required File UM RMU M 2296 D_1 Copyright All Rights Reserved Laserdyne Pty Ltd Author s MW TW Authorised TW Rev Date 14 2 14 Page 6 14 User s Manual Black Opal Xtreme Models AS DYNE Flat Panel Display Systems TECHNOLOGIES 6 4 6 3 Restore Set up Defaults e From the Defaults menu select CURRENT 6 4 6 4 Reboot the System NOTE this function is the same as turning the system off and then on again using the On Off bution It is used during software maintenance activities e From the Defaults menu select REBOOT 6 4 6 5 Set the System to Standby NOTE this function is the same as turning the system off using the On Off button It is used during software maintenance activities e From the Defaults menu select STANDBY 6 4 7 Shut down e Press th
20. ndow do not scrub File UM RMU M 2296 D_1 Copyright All Rights Reserved Laserdyne Pty Ltd Author s MW TW Authorised TW Rev Date 14 2 14 Page i User s Manual Alle 5 Black Opal Xtreme Models EMS DYNE Flat Panel Display Systems TECHNOLOGIES Tracking Records This document is appropriate for the following product configurations Initial Configuration Number File UM RMU M 2296 D_1 Copyright All Rights Reserved Laserdyne Pty Ltd Author s MW TW Authorised TW Rev Date 14 2 14 Page ii User s Manual Black Opal Xtreme Models EMS DYNE Flat Panel Display Systems TECHNOLOGIES TABLE OF CONTENTS Chapter Page 1 INTRODUCTION 1 1 1 1 Scope 1 1 1 2 Document Structure 1 1 2 SAFETY 2 1 2 1 Electrical Safety 2 1 2 2 System Protection 2 1 3 PACKING HANDLING STORAGE amp TRANSPORTATION 3 1 Packing Unpacking and Inspection Www ww aii idk 3 2 Handling 3 3 Storage 3 4 Transportation 4 SYSTEM DESCRIPTION 4 1 4 1 General Purpose 4 1 4 2 General Description 4 1 4 2 1 General 4 1 4 2 2 Display 4 1 4 2 3 Auto Backlight Reduction 4 1 4 2 4 Upgrades 4 2 4 2 5 Additional Features 4 2 4 3 System Contents 4 2 5 SYSTEM SPECIFICATIONS amp SET UP 5 1 6 OPERATION 6 1 6 1 Controls 6 1 6 2 Indicators 6 2 6 3 Button Labelling Adjustments amp Menu Presentation 6 2 6 4 Operating Procedures 6 3 6 4 1 Start up 6 3 6 4 1 1 Starting Up 6 3 6 4
21. nly by authorised service personnel CAUTION avoid scratching abrading or contaminating the surface of the display window do not scrub e Clean display screens and control panels with a soft cloth and spirit e Clean housings with a soft cloth and spirit e Clean connectors and mounting points with a soft brush 7 2 Replacing Desiccant Larger Black Opal Xtreme models are fitted with a desiccant capsule in the rear of the unit The largest models carry two The desiccant should be checked and replaced in any of the following events on screen advice to check desiccant is displayed on boot up internal fogging of the display window occurs or a six month period has elapsed since the last time desiccant was checked e Unscrew the outer exposed knurled ring s and extract the capsule s Remove the knurled cap s from the other end of the capsule s e Check desiccant colour and replace if it is no longer blue e Recap the capsule s and screw back into the unit File UM RMU M 2296 D_1 Copyright All Rights Reserved Laserdyne Pty Ltd Author s MW TW Authorised TW Rev Date 14 2 14 Page 7 1 User s Manual Black Opal Xtreme Models EMS DYNE Flat Panel Display Systems TECHNOLOGIES APPENDIX A FAULTFINDING GUIDE Probable Cause s oo will not turn a no power from remote a check power supply amp source specifications harness amp connections Power supplied but a temperature
22. ns The last phase is the loading of the default screen layout This can be either the last selected layout or a fixed layout This is pre configured prior to delivery to suit specific customer requirements 6 4 1 3 Bypassing the Boot up Sequence If the Ramp up Mode has been selected this can be bypassed by pressing any of buttons 2 to 5 on power up and holding it until the backlight shows The number of the button pressed determines the backlight level with button 5 being maximum button 4 being less intense button 3 being low intensity and button 2 being the NVG compatible mode Performing this action not only sets the initial backlight level without ramping up it also skips the logo and version presentations File UM RMU M 2296 D_1 Copyright All Rights Reserved Laserdyne Pty Ltd Author s MW TW Authorised TW Rev Date 14 2 14 Page 6 4 User s Manual Black Opal Xtreme Models SS DYNE Flat Panel Display Systems TECHNOLOGIES NOTE this method of setting a backlight level applies only to the boot up sequence the normal method of adjusting backlight level is using the and buttons 6 4 2 Primary Button Functions After boot up Press MENU button 1 to access menu functions or Press LAYOUT button 2 to show the predefined screen lay outs then press the appropriate button to select the desired lay out see appendices for instructions on how to create screen a lay out under the Se
23. nstalled there are no safety procedures required to protect the operator from the display itself NOTE the On Off button switches the unit from standby to operating status it does not cut the unit off entirely from the external power input 2 2 System Protection The system is internally protected against e reverse polarity e over voltage e over current File UM RMU M 2296 D_1 Copyright All Rights Reserved Laserdyne Pty Ltd Author s MW TW Authorised TW Rev Date 14 2 14 Page 2 1 User s Manual Black Opal Xtreme Models EMS DYNE Flat Panel Display Systems 77 gt TECHNOLOGIES 3 PACKING HANDLING STORAGE AND TRANSPORTATION CAUTION On receipt of your Black Opal Xtreme immediately report any damage to packaging or contents to your supplier 3 1 Packing Unpacking and Inspection To unpack on first receipt 1 carefully open the outer packaging do not slit cartons deeper than sealing tape 2 remove the Black Opal Xtreme components and any Manuals and ancillary items from the carton 3 remove the display from its plastic bag wrap 4 remove the protective sheet from the front of the display 5 retain packing materials if required for future use Packing is in the reverse order 3 2 Handling Touching or abrading any exposed optical surface is to be avoided Environmental conditions specified in this manual should not be exceeded 3 3 Storage The equipment may be stored
24. ons 1 to 5 will restore the labels without initiating a new function In any menu button 2 becomes EXIT button 5 becomes ENTER and buttons 1 3 amp 4 are disabled In any menu the BACK item will return to the previous menu Select menu items using the scroll adjust buttons Press ENTER to enable the selection Press EXIT to abandon the menu and any unfinished adjustments The scroll adjust buttons will be labelled as PARAMETER to indicate which parameter is selected for adjustment Backlight can be adjusted at any time by using the scroll adjust buttons unless ZOOM or MENU has been selected Zoom can be adjusted at any time by using the scroll adjust buttons unless BACKLT or MENU has been selected File UM RMU M 2296 D_1 Copyright All Rights Reserved Laserdyne Pty Ltd Author s MW TW Authorised TW Rev Date 14 2 14 Page 6 2 User s Manual a 2 Black Opal Xtreme Models EMS DYNE Flat Panel Display Systems TECHNOLOGIES e Various display settings can be adjusted once they have been selected through the menu structure by using the scroll adjust buttons e Once ENTER has been pressed the previous menu will be presented if no concurrent options are available else the current menu will be maintained if more than one item in it can be enabled or adjusted concurrently e Whenever button labels are displayed the name of the current screen lay out is also displayed above the top most
25. ons and adjustments effecting the appearance of the display Any settings made under the User s menu structure will be retained by the unit and will over ride the settings made under the Set up menu structure The operator can at any time return all parameters to the settings selected under the Set up menu structure The Set up menu structure is not used in normal operation It is only available when a special button combination is activated lt allows basic and advanced set up of inputs outputs corrections and adjustments The settings selected in the Set up menu structure become the default settings for parameters in the User s menu structure Set up personnel may at any time return all parameters under the Set up menu structure to the factory default settings The set up menu is generally not required by users or installation personnel as the display will be supplied pre configured to suit the specifics of the intended application Specifics about accessing the set up menu are available to approved personnel on request File UM RMU M 2296 D_1 Copyright All Rights Reserved Laserdyne Pty Ltd Author s MW TW Authorised TW Rev Date 14 2 14 Page B 1
26. ough antireflection coated window which also provides EMI EMC shielding All models are button operated 4 2 2 Display Images are displayed on a backlit LCD that may be viewed in full direct sunlight down to full darkness and feature backlight settings suitable for low light viewing for viewing with Night Vision Devices and completely off for black out conditions 4 2 3 Auto Backlight Reduction To reduce power consumption and as part of the Black Opal Xtreme thermal management scheme the backlight will automatically reduce to 300 nits if e the current backlight setting is greater than 300 nits and e no button has been pressed for more than 120 seconds and the internal temperature is above a preset limit Pressing any of buttons 1 to 5 will cause the system to return to the current backlight setting File UM RMU M 2296 D_1 Copyright All Rights Reserved Laserdyne Pty Ltd Author s MW TW Authorised TW Rev Date 14 2 14 Page 4 1 User s Manual wit 7 Black Opal Xtreme Models SANS DYNE Flat Panel Display Systems TECHNOLOGIES 4 2 4 Upgrades The Black Opal Xtreme has been designed so that software upgrades can be downloaded easily viaa PC 4 2 5 Additional Features NOTE Image Enhancement and Digital Zoom are available whenever the main window in a Screen Lay out is video not PC input Black Opal displays have several features designed to increase the effectiveness of surveillance si
27. st buttons throughout this manual depending upon the context Scroll Adjust Buttons On Off Button N Pr 7 TA Function Buttons 1 to 5 Figure 6 1 Controls and Indicators typical File UM RMU M 2296 D_1 Copyright All Rights Reserved Laserdyne Pty Ltd Author s MW TW Authorised TW Rev Date 14 2 14 Page 6 1 User s Manual Black Opal Xtreme Models E Nr DYNE A Flat Panel Display Systems TECHNOLOGIES 6 2 Indicators The illumination behind the buttons operates as thermal status indicators in the case where the temperature is too hot or too cold for the unit to operate If the display s internal temperature is too low Warm up mode will be engaged and the button backlighting will blink at a slow rate around 0 5Hz Once the internal temperature is within operating parameters the button backlight will operate as normal If the display s internal temperature is too high it will shut down and the button backlight will blink at a fast rate around 2Hz Once the internal temperature is within operating parameters the button backlight will operate as normal 6 3 Button Labelling Adjustments 8 Menu Presentation If no button has been activated for about five seconds and no menus have been entered the button labels will be withdrawn from the screen however scroll adjust buttons will still be active for the current adjustable parameter Pressing any Function Button butt
28. t up menu structure and for descriptions of lay outs or Press ENH button 3 to enable image enhancement and allow enhancement window adjustment only available for video will be replaced by NO ENH or Press ZOOM button 4 to allow digital zoom adjustment will be replaced by BACKLT only available for video or Press FREEZE button 5 to freeze image will be replaced by UNFREEZE Press the On Off button short press to cycle the displayed menu between normal functions and Memoreyes functions if a Memoreyes is detected Hold the On Off button for 2s to power down the display NOTE you can freeze a zoomed enhanced or zoomed amp enhanced image enhance a frozen image or zoom a frozen enhanced frozen amp enhanced image NOTE Image Enhancement and Digital Zoom are available whenever the main window in a Screen Lay out is video not PC input NOTE If the Memoreyes menu option is selected then the primary buttons assume new functions Use the EXIT button to return to normal primary button functions NOTE If the video format changes from that specified in the layout use the zoom feature to re format the image on the screen File UM RMU M 2296 D_1 Copyright All Rights Reserved Laserdyne Pty Ltd Author s MW TW Authorised TW Rev Date 14 2 14 Page 6 5 User s Manual wins Black Opal Xtreme Models SS DYNE Flat Panel Display Systems TECHNOLOGIES 6 4 3 Scroll
29. u items CURRENT REBOOT and STANDBY It also displays system configuration information File UM RMU M 2296 D_1 Copyright All Rights Reserved Laserdyne Pty Ltd Author s MW TW Authorised TW Rev Date 14 2 14 Page 6 12 User s Manual Si y Black Opal Xtreme Models SS DYNE Flat Panel Display Systems TECHNOLOGIES Menu Item Result 1 Current Restores Set up values to the User parameters for the current screen lay out Reboots the system Standby Sets the system to standby e Select the desired item and press ENTER 6 4 5 6 Memoreyes Menu e Selecting the Memoreyes menu changes the function of the buttons 1 5 so as to control an external recorder 6 4 6 Working with Menus How to In every case selection of a menu item is achieved by scrolling to it with the scroll adjust up down buttons and then pressing ENTER button 5 and setting a value is achieved by adjusting it to the desired value using the scroll adjust up down buttons and then pressing ENTER button 5 Once a selection has been made or a value has been set if no other items in the current menu are still relevant the system will return to the next highest relevant menu or if other items in the current menu are still relevant the system will remain in the current menu You can progress back up the menu structure by selecting BACK or close the menu presentation entirely by pressing EXIT button 2 NOTE pr
Download Pdf Manuals
Related Search