pobierz - Elmes Elektronik
Contents
1. 5 6 4 3 4 5 6 4 13 1 2 3 4 T 1 2 3 4 1 2 3 4 5 TL 1 2 3 T 1 2 3 4 T 1 2 3 T 4 5 6 T 2 3 4 5 6 T 14 1 2 3 4 4 1 2 3 4 4 1 2 3 4 5 6 T4 L234 1 2 3 4 4 1 2 3 4 4 5 6 4 2 3 4 5 6 15 1 2 3 4 5 6 T 1 2 3 4 5 6 T 1 2 3 4 5 6 T 4 5 6 T 5 6 T 1 2 3 4 5 6 T 1 2 3 4 5 6 T 1 2 3 4 5 6 T 16 1 2 3 4 5 6 4 1 2 3 4 5 6 4 1 2 3 4 5 6 4 4 5 6 4 5 6 4 1 2 3 4 5 6 4 1 2 3 4 5 6 4 1 2 3 4 5 6 4 Gro 2 2 9 3 3 3 1 2 3 3 2 2 2 4 2 3 3 4 2 4 1 1 3 1 1 1 2 2 1 1 2 1 3 2 2 2 4 2 ups 4 2 6 4 2 6 3 1 2 5 1 6 3 1 1 1 2 1 1 1 1 6 2 1 1 1 1 4 1 1 5 1 6 3 1 1 1 6 the last raw of the Table shows up possible control solutions in respective modes e g 4 2 meaning that with the use of one double button switch a group of 4 rollers can be controlled while next double switch would control group of two rollers 1 2 3 4 5 6 roller numbers 1 2 15 16 numbers of connected wall switches TJ roller operation mode up stop down stop up stop T roller operation mode up stop up J roller operation mode down stop down Controlling more than 6 rollers Possible with the use of more than one ST6H control panels All rollers close or open function requires connec tion of wall switch to OP and CL inputs of all control panels System clock connection System clock can be connected to the ST6H panel through dedicated input D N Connecting the D N to COM would close all opened rolle2. controller inputs R3 and C2 shorted if the switch is not connected and next hand transmitter should be learned to the controller using transmitter s button No 2 see par 1 of the program ming procedures Since then button No 2 would open rollers No 1 2 3 Similar steps should be taken with button No 4 of the hand transmitter using wall switch No 8 or shorting inputs R4 with C2 Remaining buttons can operate according to any other function offered in Table 1 Advice to delete functions programmed to hand transmitter buttons the transmitter must be deleted from controller s memory It is suggested to use deliberately two different buttons while at learning procedure of the transmitter to the controller procedures 1b and Ic Operation with Elmes CH32H hand transmitter This transmitter generally incorporates four CH8H hand transmitters functions The advantage of using this transmitter is that number of button combinations may be extended four fold and more window rollers can be controlled by single unit Lighting control with the use of ST6H Besides its standard application in window rollers environment the ST6H controller may also be used to control operation of six lamps or light beams To do so controller inputs O and C of each channel must be shorted and continuous bi stable relay output set on time must be programmed The lamps can be switched on and off by the use of transmitter buttons or wall switches PROGRAMMING PROCEDURES 1 Lea
3. ed with the use Elmes CH8H eight chan nel transmitter The transmitter is equipped with four main control button switches as well as side sliding ee switch aimed for selection of operation function of the main buttons Required functions must be first DO OG selected by the side switch and confirmed by shining LED combination see figure below prior to using the main buttons of the transmitter General operation mode of the transmitter depends on settings made OGO DG by jumper JP4 as follows With JP4 shorted and button No 1 used while learning the transmitter to the ST6H controller the 1 6 main button switches would independently control operation of up to 6 rollers in up stop down stop up stop mode while buttons 7 and 8 would control open and close movement of all six rollers With JP4 shorted and button other than No 1 e g 4 used while learning the transmitter to the ST6H controller button No 3 and No 4 would control open and close movement of all six rollers respectively Remaining switches will be inactive or may be used for other application With JP4 opened In this mode all buttons of the hand transmitter can operate according to programmed selected function as described in Table 1 Example in need to program button No 2 to open first three rollers and button No 4 to close the rollers jumpers JP1 JP3 should be set to OFF ON ON position the rollers should be switched on and off by the use of wall switch No 7 or respective
4. elmes DYNAMIC CODE REMOTE CONTROLLER FOR UP TO SIX WINDOW ROLLERS ST6H electronic The controller offers dynamic code wireless as well as wired operation control for up to six window rollers powered by electric AC tube motors with integral terminal switches Operation On command received from hand transmitter or wired wall switch one or more roller motors are started Multiple motors are started sequentially with 0 5s time intervals JP5 shorted or with 0 13s intervals JP5 opened Moving rollers are stopped either by received next com mand or by passage of programmed rotation time programming procedures p 2 It is possible to program continuous AC motor powering time thus protecting the roller against manual opening while in roller closed end position AC motor termination switch will power motor rotation and closes the roller on every attempt of manual lifting the closed roller Recommended for operation with the ST6H controller are multi channel Elmes CH8H and CH32H hand transmitters One two or four channel transmitters can also be used if necessary Wired control of rollers connected to the controller is performed by up to 18 monostable dedicated wall switches with marked roller direction movement arrows Some of the switches can be used to control all or group of rollers Operation mode of the wall switches are user set by jumpers as described in Table 1 of this instruction manual Operation with hand transmitter Example operation is explain
5. es per sonal safe rocedures to be taken Installation MUST NOT be made with supply cable connected to mains Prior to installation disconnect mains supply WARNING Control unit and electric AC motors are 230VAC mains su
6. rning transmitter s to controller s memory maximum 32 a press control unit PRG switch for less than 2 seconds PRG LED lights on b press required transmitter button LED switches off c press again the same transmitter s button blinking LED confirms end of procedure 2 Programming tube motor rotation time 4 seconds set as standard a press control unit PRG switch for more than 2 and less than 8 seconds PRG LED lights on Releasing the switch PRG LED sets off b press any hand transmitter button or wired wall switch to start motor rotation c after required motor rotation time has lapsed max 60 minutes press the transmitter button or wired wall switch again motor stops d after two seconds PRG LED starts blinking confirming end of the procedure Advice To obtain continuous bi stable output relay set on time double pressing of transmitter s button is required with less than two sec onds interval in programming step c above 3 Deleting all transmitters from control unit memory press receiver s PRG switch PRG LED lights on and hold pressed for more than 8 seconds until the receiver LED starts blinking confirm ing end of the procedure Transmitter memory in the controller is cleared while programmed timings remain unchanged Technical Specification e control panel mains supply 230VAC 500mA fused receiver band 433 92MHz with max operation range 200m e power relay control outputs max 16A 250VAC max number of hand
7. rs while disconnecting D N from COM would open closed rollers D N inputs of many controllers can be connected together so that single system clock would control all rollers Installation schematic diagram Z ZI 4 71 Installation The ST6H control panel is powered from 230VAC Control nso Z Zt Edi 71 mains line For safety reasons MOTOR Tes H amp H board 6 pl geallas installation can be made with zi 9 LI 41 LI L mains cable DISCONNECTED The panel with integral radio O S oto receiver may be installed indoor Oo S SoH only and far from harsh environ mental conditions like high or low e temperatures high humidity or TE c3 LIVE m Q NEUTRALO 2 Q H S radio and electric interference Antenna wire of the ST6H con l N o lt DHMH GH GHG Oo troller should be downwards GROUND O il LJ com directed and cannot be fixed or Uee na eel DN g glued to wall Complete connec wr Y S tion diagram with mains cable MOTOR 6 Z AC tube motors and external wall ue lf S la switches is shown on installation z S GND schematic diagram o S oto ANT IMPORTANT ol S mr 230VAC supply LIVE wire must O opening be connected to L terminal and C closing NEUTRAL wire must be con nected to N terminal lied and their installation requir
8. s R1 4 and C1 4 as shown on connection schematic diagram below Prior to firm installation of the controller one of eight possible operation modes should be selected If individual control of every window roller in up stop down stop up way is at priority then operation mode 1 3 should be selected If two button switches are installed then operation mode is 4 6 Mode 7 and 8 are used if selected window rollers are used in groups of 2 3 or 4 units e g with extremely wide window display facade In the next step roller groups must be defined With the groups definition ready operation mode should be selected in the bottom end raw of Table 1 Switch Mode 1 Mode 2 Mode 3 Mode 4 Mode 5 Mode 6 Mode 7 Mode 8 num JP1 JP2 JP3 JP1 JP2 JP3 JP1 JP2 JP3 JP1 JP2 JP3 JP1 JP2 JP3 JP1 JP2 JP3 JP1 JP2 JP3 JP1 JP2 JP3 ber ON ON ON OFF ON ON ON OFF ON OFF OFF ON ON ON OFF OFF ON OFF ON OFF OFF OFF OFF OFF 1 1 TL 1 TL 1 TL 1 T iEn 129 1 T ET 2 Z T 2 TL 2 0 iet 1 4 tet l 4 ie 3 3 TW 3 TL 3 TL 2 T 22 7 EN eT FT 4 4 TL 4 TL 4 TL a Ve L 2 1 el 5 5 TL 5 TL 5 TL 3 T 3 7 3 T 3 T 1 2 T 6 6 TL 6 TL 6 TL 3 1 3 1 3 1 3 4 1 2 4 7 1 2 T 1 2 3 1 2 3 TL 4 T 4 T 4 T 4 T 34 7 8 1 2 4 1 2 3 4 4 5 6 N 4 4 4 1 4 4 4 4 3 4 4 9 3 4 T 4 5 6 T ELEN 5 7 5 7 5 7 1227 5 6 T 10 3 4 4 4 5 6 4 3 4 N ab 5 1 L 1 2 5 6 4 11 5 6 T 5 6 T 5 6 4 6 7 6 T 6 7 5 6 T 3 4 5 6 T 12 56 4 56 4 1 2 3 4 TL L 6 4 J
9. transmitters 32 Manufacturer ELMES ELECTRONIC 54 611 Wroclaw PL ul Avicenny 2 tel 4871 784 59 61 fax 4871 784 59 63 Elmes Electronic declares that the product has been manufactured and tested to comply with the following standards EN 60950 1 2001 electric safety EN 301 489 1 V1 4 1 2002 08 EMC for radio equipment EN 301 489 3 V1 2 1 2002 08 EMC for Short Range Devices EN 300 220 3 V1 1 1 2000 09 EMC and Radio Spectrum Matters Manufacturer s Limited Warranty Elmes Electronic remote control sets carry one year manufacturer s warranty as from date of purchase The warranty is limited to the replacement of faulty original parts or repair defects of improper manufacture Damage faulty use or improper handling by the user or installer as well as any changes in product s hardware or software caused by the user violets the warranty and all due repair costs will be charged Elmes Electronic shall not be responsible for any direct or indirect personal or material damage caused by its products failure to operate correctly Elmes Electronic reserves the right to change product specification without prior notice KEELOQ is a registered trademark of Microchip Technology Inc USA www elmes pl e mail elmes elmes pl Elmes Elektronik 09 2006 All rights reserved Table 1 Presentation of wall switch control modes depending on JP1 JP2 JP3 presets The numbers in column one represent respective wall switches connected to input
Download Pdf Manuals
Related Search