12804501 - LG Owner`s Manual - EN.pmd
Contents
1. DONOT cover or block filter or other openings on equipment DONOT store this equipment outdoors DO NOT use this product near water for example near a kitchen sink in a wet basement a swimming pool or a similar location DO NOT immerse cord or plug in water Keep cord AWAY from HEATED surfaces DO NOT let cord hang over edge of table or counter For commercial use only PRECAUTIONS TO AVOID POSSIBLE EXPOSURE TO EXCESSIVE MICROWAVE ENERGY DO NOT attempt to operate this oven with the door open since open door operation can result in harmful exposure to microwave energy It is important not to defeat or tamper with the safety interlocks DO NOT place any object between the oven front face and the door or allow soil or cleaner residue to accumulate on sealing surfaces DO NOT operate the oven if it is damaged It is particularly important that the oven door close properly and that there is no damage to the 1 door bent 2 hinges and latches broken or loosened 3 door seals and sealing surfaces The oven should not be adjusted or repaired by anyone except properly qualified service personnel SAVE THESE INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS To avoid risk of fire in the oven cavity Liquids such as water coffee or tea are able to be overheated beyond the boiling point without appearing to be boiling due to surface tension of the liquid Visible bubbling or boiling when the container is2. a DONOT overcook food Carefully attend oven when paper plastic or other combustible materials are placed inside the oven to facilitate cooking Remove wire twist ties from paper or plastic bags before placing bag in oven If materials inside the oven ignite Keep oven door CLOSED turn oven off and disconnect the power cord or shut off power at the fuse or circuit breaker panel DO NOT use the cavity for storage DO NOT leave paper products cooking utensils or food in the cavity when not in use removed from the microwave oven is not always present THIS COULD RESULT IN VERY HOT LIQUIDS SUDDENLY BOILING OVER WHENA SPOON OR OTHER UTENSIL IS INSERTED INTO THE LIQUID To reduce the risk of injury to persons Do not overheat the liquid Stir the liquid both before and halfway through heating it Do not use straight sided containers with narrow necks After heating allow the container to stand in the microwave oven for a short time before removing the container Use extreme care when inserting a spoon or other utensil into the container 44 CAUTION To avoid personal injury or property damage observe the following 1 Do not deep fat fry in oven Fat could overheat and be hazardous to handle Do not cook or reheat eggs in shell or with an unbroken yolk using microwave energy Pressure may build up and erupt Pierce yolk with fork or knife before cooking Pierce skin of potatoes tomatoes and similar foo
3. Dry thoroughly Discharge Air Vents Filter is located below oven door Clean air intake filter weekly for proper airflow Wash filter in hot water and mild detergent Do not use oven without filter in place Remove filter to clean Air Intake Filter Important To avoid overheating and oven damage clean air filter regularly 1 Turn thumbscrew counterclockwise and remove filter for cleaning Open oven door to deactivate oven timer Clean with mild detergent in warm water using Control Panel soft sponge or cloth Before Calling for Service A WARNING To avoid electrical shock which can cause severe personal injury or death do not remove outer case at any time Only an authorized ACP servicer should remove outer case Problem Oven does not operate Oven operates intermittently Possible Cause Confirm oven is plugged into dedicated circuit Confirm oven is on grounded and polarized circuit Contact electrician to confirm Check fuse or circuit breaker Check air filter and discharge areas for obstructions If oven does not accept entries when pad is pressed If oven malfunctions or shows F with a number Oven operates but does not heat food Make sure oven is on Open and close oven door Press pad again Oven control is equipped with a self diagnostic system Self diagnostic system alerts you if there is a error or problem When electronic control signals a problem follow steps lis
4. Press a numbered pad to change the cooking factor e Cooking factor can be set from 10 to 100 e Default is 80 e Pad 5 would change the cooking factor to 50 e Pad 3 would change the cooking factor to 30 6 Press START pad to save changes ako User Options Electronic Control Didn t like an option Factory settings are marked in bold To change the oven back to the factory setting simply select the option that is marked in bold My changes weren t saved In order for any changes to be saved the START pad must be pressed after selecting an option Shutting the oven door or pressing the STOP RESET pad will not save changes Numbered Pads 1 OP 10 Display Changing user options Options such as single or double pad programming beep volume and maximum cooking time can be changed to suit individual preferences To change options 1 Open oven door e If door is closed or STOP RESET pad is pressed before programming is complete changes are discarded and microwave exits programming mode Press and hold pad 2 for approximately 5 seconds e This begins options mode e Microwave will beep and OP displays Microwave is now in programming mode Press number pad that controls option to be changed e See table below for options e Current option will display Press number pad again to change the option e Each time pad is pressed option will change e Match code displayed with code for
5. Splatter shield can be removed for easier cleaning The shield snaps into a lip in the front of the oven and two slots in the back wall Unplug oven to stop antenna from rotating Place your thumbs in the two indentations in the front of the shield Press firmly toward the back and carefully lower the shield away from the antenna Pull the shield out of the back slots and out of the oven e DO NOT bend antenna Reinstall splatter shield by fitting shield tabs into the two slots at the top of the back Lift front and push back until shield snaps into place 6 Reconnect power to oven e Verify antenna operation by placing a glass or cup of water in the unit Close the oven door and start oven A rotating shadow should be visible above the splatter shield AON a PART CARE AND CLEANING RECOMMENDATION Clean microwave oven with mild detergent in warm water using soft sponge or cloth Wring sponge or cloth to remove excess water before wiping equipment If desired boil a cup of water in microwave oven to loosen soil before cleaning Interior Exterior and Door Important e Do not use abrasive cleansers or cleaners containing ammonia or citrus These could damage finish e Never pour water into microwave oven bottom e Do not use water pressure type cleaning systems Check monthly for a buildup of cooking vapors along intake and discharge louvers on bottom and back of oven Clean air vents with damp cloth to ensure proper airflow
6. message displays clean the air filter CLEAN FILTR thoroughly Cleaning the air filter will not shut some models off the message The message will stop displaying automatically after 24 hours Removable Splatter Shield Not Shown located inside oven Oven Door Window and Interior Light Oven Display Oven Control Filter JE 888 88 cook oz HEATER Ttable OFF Display Some items in the display can be seen but are not available depending on model READY Ready Ready displays when an oven control will accept entries ARAA COOK oz at HEATER Ttable OFF Cooking Displays 33 33 displays total cooking time When more than one cooking stage is programmed total time for all stages displays COOK displays when oven is operating DEFROST 20 MEDIUM 50 or MED HI 70 will display to indicate microwave power level being used HOLD 0 does not display COOK If oven power level is set to 0 oven does not heat for programmed time If no power level is displayed the microwave is operating at 100 power Using the Oven Control Electronic Control Interrupting Operation Open oven door or press STOP RESET pad to interrupt operation Display may continue to show countdown time Close door and press START pad to resume oven operation Do I have stage programming Stage programming is not shown with a pad on the oven To verify that your m
7. 0 Allows 10 0 9 preprogrammed pads some models OP 91 Allows 100 00 99 preprogrammed pads Double Digit Operation 0 OP 00 Do not display message Clean Filter Message OP 01 Display message for 24 hours every 7 days OP 02 Display message for 24 hours every 30 days OP 03 Display message for 24 hours every 90 days 10 Dial Operation Dial option is available on some models only The switching operation of this microwave oven can cause voltage fluctuations on the supply line The operation of this oven under unfavorable voltage supply conditions can have adverse effects This device is intended for the connection to a power supply system with a maximum permissible system impedance Zmax of 0 2 Ohms at the interface point of the user s supply The user has to ensure that this device is connected only toa power supply system which fulfills the requirement above If necessary the user can ask the public power supply company for the system impedance at the interface point _ lt HEATING GUIDE xz Oo o gt DO NOT power spray Heating 1 Oven Wall Clearances A For North American UL CSA models allow at least 2 5 1 cm of clearance around top of oven For International 50 Hz models allow at least 12 30 cm of clearance around top of oven Proper air flow around oven cools electrical components With restricted air flow oven may not operate pr
8. Owner s Manual Contents Model Identification PRECAUTIONS TO AVOID POSSIBLE EXPOSURE TO EXCESSIVE MICROWAVE ENERGY IMPORTANT SAFETY INSTRUCTIONS Earthing Instructions Installation Display and Features Commercial Microwave Oven Eee Programming the Oven Control Electronic Models F User Options Keep these instructions for future reference Electronic Models If the oven changes ownership this manual Dial Operation must accompany oven Digital Dial Operation Care and Cleaning Before Calling for Service Model Identification When contacting ACP provide product information Product information is located on oven serial plate which is located on the back side of the oven Record the Warranty service must be performed by an authorized following information ACP servicer ACP also recommends contacting an authorized ACP servicer if service is required after Model Number Manufacturing Number Walley se ieee Serial or S N Number Date of purchase Dealer s name and address Any questions or to locate an authorized ACP servicer call toll free 1 866 426 2621 inside the U S A or Canada or 1 319 368 8120 outside the U S A or Canada IMPORTANT SAFETY INSTRUCTIONS A Recognize this symbol as a SAFETY message When using electrical equipment basic safety precautions should be followed to reduce the risk of burns electrical shock fire or injury to persons 1 READ all instructions b
9. clean condition Infrequent cleaning could adversely affect the life of the appliance and possibly result in a hazadous situation SAVE THESE INSTRUCTIONS Installation Unpacking Oven e Inspect oven for damage such as dents in door or inside oven cavity e Report any dents or breakage to source of purchase immediately Do not attempt to use oven if damaged e Remove all materials from oven interior e If oven has been stored in extremely cold area wait a few hours before Radio Interference To avoid risk of electrical shock Microwave operation may cause interference to radio television or a similar or death do not alter the plug oven Reduce or eliminate interference by doing the following e Clean door and sealing surfaces of oven according to instructions in To avoid risk of electrical shock or death this oven must be earthed Care and Cleaning section Grounding Earthing e Place radio television etc as far as possible from oven Instructions e Use a properly installed antenna on radio television etc to obtain Oven MUST be grounded stronger signal reception Grounding reduces risk of electric shock by providing an escape wire for Oven Placement the electric current if an electrical e Do not install oven next to or above source of heat such as pizza oven short occurs This oven is equipped or deep fat fryer This could cause microwave oven to operate with a cord having a ground wire with improperly and could sh
10. d i Open oven door e Factory default setting for cooking time is 10 minutes Cooking time can be changed and set to 60 minutes e If door is closed before programming is complete changes are discarded current or assigned time will show in display 3 Turn Dial to change time setting e Time can be set from zero 0 00 seconds to five minutes 5 00 e If the assigned time is 0 00 the 30 QUICK SET pad is effectively disabled 4 Press START pad to save changes Options can be changed to suit individual preferences A 2 Press and hold the 30 QUICK SET pad Refer to section on changing for approximately 5 seconds options e This activates the programming 3 Press a power level pad to change mode power level if desired If no power e Microwave will beep and either level is selected unit will default to 100 e Power level can be set from full Can I change an option power 100 to 70 50 or DEFROST 20 4 Press START button To change options e Oven begins operation and time 1 Open oven door 3 counts down 5 When cooking time has elapsed microwave energy stops and oven Press the Hidden Pad to advance to the desired option to be changed e See table below for options Turn Dial to change option setting e If door is closed before programming is complete changes are discarded and microwave exits options programming 4 signal sounds 9 mode Interrupting Operation 2 Open oven door to
11. desired option Press START pad to save changes e OP shows in display e To change additional options repeat steps 3 and 4 e Changes appear after door is closed or STOP RESET pad is pressed Options Factory Settings in Bold 3 second continuous beep End of Cycle Beep OP 11 Continuous beep until door is opened OP 12 5 beep bursts until door is opened 2 OP 20 Eliminates beep Speaker Volume OP 21 Sets volume to low OP 22 Sets volume to medium OP 23 Sets volume to high 3 OP 30 Prevents beep when pad is pressed Key Beep OP 31 Allows beep when pad is pressed 4 OP 40 15 seconds after oven door is opened keyboard disabled Keyboard Enable OP 41 30 seconds after oven door is opened keyboard disabled Window OP 42 1 minute after oven door is opened keyboard disabled OP 43 2 minutes after oven door is opened keyboard disabled 5 OP 50 Prevents adding heating time while oven is heating Add Time During OP 51 Allows heating time to be changed while oven is heating when a memory pad Heating is pressed 6 OP 60 Allows oven to resume heating time countdown after door is opened during Reset Door Open cycle OP 61 Cancels heating time count down after door is opened during cycle 7 OP 70 Allows 60 minutes of heating time some models OP 71 Allows 10 minutes of heating time Maximum Heating Time 8 OP 80 Allows use of preprogrammed pads only Manual Operation OP 81 Allows use of manual time entry and preprogrammed pads 9 OP 9
12. ds before cooking with microwave energy When skin is pierced steam escapes evenly Do not operate equipment without load or food in oven cavity Use only popcorn in packages designed and labeled for microwave use Popping time varies depending on oven wattage Do not continue to heat after popping has stopped Popcorn will scorch or burn Do not leave oven unattended Do not use regular cooking thermometers in oven Most cooking thermometers contain mercury and may cause an electrical arc malfunction or damage to oven Do not use metal utensils in oven Never use paper plastic or other combustible materials that are not intended for cooking 9 When cooking with paper plastic or other combustible materials follow manufacturer s recommendations on product use Do not use paper towels which contain nylon or other synthetic fibers Heated synthetics could melt and cause paper to ignite Do not heat sealed containers or plastic bags in oven Food or liquid could expand quickly and cause container or bag to break Pierce or open container or bag before heating To avoid pacemaker malfunction consult physician or pacemaker manufacturer about effects of microwave energy on pacemaker Anauthorized servicer MUST inspect equipment annually Record all inspections and repairs for future use 14 Clean oven regularly and remove any food deposits 15 To avoid surface deterioration keep the ovenina
13. e pad programming the display will show PROGRAMI when Programming Pads oven default to allow double pad programming see User Option section To change the amount of time or the power level for a preset pad e READY displays e If door is closed or STOP RESET pad is pressed before programming programming mode Press and hold pad 1 for approximately 5 seconds e Microwave will beep and PROGRAM displays Oven is in programming mode e Press two pads if reprogramming a double pad program MENIM e Power level and cooking time display 50 Enter cooking time by using the number pads Press a power level pad to change power level if desired e To enter another cooking stage for that pad press TIME ENTRY pad again models Press START pad to set new programming changes to the e PROGRAM displays e If START is not pressed changes will not be saved Oven is shipped from the factory for single pad programming To change the 1 Open oven door is complete changes are discarded and microwave exits E e This begins programming mode Press pad to be reprogrammed e If power level does not display microwave is set to full power Enter cook time and power level as in steps 4 and 5 some models e Up to four different stages can be programmed some pad Press STOP RESET pad or close oven door to exit programming mode programming pads for single or double digit cooking sequenses To change the oven s default to allow either single pad
14. efore using equipment 2 READ AND FOLLOW the specific PRECAUTIONS TO AVOID POSSIBLE EXPOSURE TO EXCESSIVE MICROWAVE ENERGY on this page This equipment MUST BE EARTHED Connect only to properly EARTHED outlet See EARTHING INSTRUCTIONS on page 5 Install or locate this equipment ONLY in accordance with the installation instructions in this manual Some products such as whole eggs and sealed containers for example closed glass jars are able to explode and SHOULD NOT be HEATED in this oven Use this equipment ONLY for its intended use as described in this manual Do not use corrosive chemicals or vapors in this equipment This type of oven is specifically designed to heat cook or dry food It is not designed for industrial or laboratory use As with any equipment CLOSE SUPERVISION is necessary when used by CHILDREN See door cleaning instructions on page 13 of this product safety manual DO NOT heat baby bottles in oven Baby food jars shall be open when heated and contents stirred or shaken before consumption in order to avoid burns DONOT operate this equipment if it has a damaged cord or plug if it is not working properly or if it has been damaged or dropped This equipment including power cord must be serviced ONLY by qualified service personnel Special tools are required to service equipment Contact nearest authorized service facility for examination repair or adjustment
15. he user can program up to four different power level changes and the specific amount of cooking time at each power level Each power level cooking time combination is known as a stage Up to four stages can be programmed Stage cooking is available only in some electronic control models fie User Options This microwave can be set for specific user preferences Options such as beep volume maximum cooking time and the number of programmable pads can be changed To change different options see User Options in this manual Display and Features some models Cooking Display DISPLAYS DESCRIPTION REAL READY displays when oven control will accept entries aa a Displays cooking time If stage cooking is E programmed total cooking time is displayed HOLD 0 These settings display the current microwave power level used If no display is shown microwave is running at full power 100 DEFROST 20 MEDIUM 50 MED HI 70 COOK is displayed while the oven is generating microwave energy during a cooking cycle COOK Programming Display DISPLAYS DESCRIPTION Displays when oven is in programming mode Displays when oven is in user option mode User options can then be set or specified Displays when the QTY 2X pad is pressed When programming a specific cooking stage The oven beeps twice at the change of each stage 1 COOKING through 4 This oven displays CLEAR FILTR every 7 days When the
16. icrowave has stage programming refer to the Quick Start Guide provided with the microwave or call your authorized Amana dealer QTY 2X Pad some models To increase cooking time by a specific cooking factor when cooking more than one serving The cooking factor is a percentage of the original cooking time from 10 to 100 1 Open oven door and place food in oven Close door e READY displays Fan and light will turn on 2 Press QTY 2X pad e Amount of time added is a percentage of the original preprogrammed cooking time e The percentage can be changed See Programming the Oven Control section in this manual 3 Press desired preprogrammed pad or pad sequence 4 Oven begins cooking Displayed cooking time is the total of original cooking time plus the added 2X time Manual Time Entry To cook food using a specific entered time and power level 1 2 Open oven door and place food in oven Close door e READY displays Fan and light will turn on Press TIME ENTRY pad e READY and 0000 display e f pad does not work open and close oven door and try again Enter cooking time by using the numbered pads Press a power level pad to change power level if desired some models POWER LEVEL displays with the power setting DD indicates 0 microwave power 2 indicates 20 55 indicates 50 and 1E indicates 70 microwave power If a number is not displayed with POWER LEVEL the microwave is set to full po
17. interrupt operation or turn time entry knob counterclockwise to 0 mode To resume microwave oven operation close door and press START If time was changed to 0 time will need to be reset and then press START Changing Time and Power Canceling Mistakes Numbered Pads 1 End of Cycle Beep Press and hold the Hidden Pad for approximately 5 seconds e This begins options programming Display e OP and option number appear in display e See table below for options 5 Press START pad to save changes e To change additional options repeat e Microwave will beep and OP steps 2 5 appears in display e Changes appear after door is closed Options Factory Settings in Bold 3 second continuous beep Continuous beep until door is opened 5 beep bursts until door is opened 2 Speaker Volume Heating time and power level can be changed at any time while the oven is operating Turn knob to desired new setting To set cooking time to zero turn knob counterclockwise to Eliminates beep Sets volume to low Sets volume to medium Sets volume to high SOF 3 Prevents beep when pad is pressed Key Beep Allows beep when pad is pressed 4 15 seconds after oven door is opened keyboard disabled Keyboard Enable 30 seconds after oven door is opened keyboard disabled Window 1 minute after oven door is opened keyboard disabled 2 minutes after oven door is opened keyboard disabled 5 Preven
18. me and also ends a programming or user option cycle When the STOP RESET pad is used to end a programming or option change the changes are discarded Single Pad Programming example of pad 7 shown This feature enables each numbered pad to be programmed for a specific cooking procedure use To use this feature simply program the pad to the desired length of time and power level To use this feature press the pad once and the microwave will begin cooking EET Double Pad Programming some models This feature enables 100 programmed entries to be made Each entry will be assigned a double digit number for example 07 as shown When using the double pad programming two pads must be pressed to start the cooking cycle Manual Time Entry In addition to programmable pads this microwave also accepts specific time entry by using the TIME ENTRY pad Using manual time entry does not affect the programmed buttons QTY USS QTY 2X Pad The QTY 2X pad increases a preset cooking time by a percentage of the original cooking time cooking factor The user may specify the percentage and it can be changed for individual cooking sequences This feature is very useful for cooking multiple servings of foods The QTY 2X pad can be used with either single or double pad programming To change the cooking factor see Programming the Oven Control ri Stage Cooking Stage cooking is a cooking sequence with specific power stage changes T
19. ntial Earthing Terminal export only Oven teres Equipment has secondary earthing terminal Terminal provides external The switching operation of this microwave oven can cause voltage fluctuations earthing connection used in addition on the supply line The operation of this oven under unfavorable voltage supply to earthing prong on plug Located conditions can have adverse effects This device is intended for the connection on outside of oven back terminal is to a power supply system with a maximum permissible system impedance marked with symbol shown below Zmax of 0 2 Ohms at the interface point of the user s supply The user has to ensure that this device is connected only to a power supply system which fulfills the requirement above If necessary the user can ask the public power supply company for the system impedance at the interface point Display and Features some models If These Features are Different from Yours These features are intended to show the variety that is available in the product line If your microwave does not have all the options that are shown it is not a mistake The information provided applies to several of the models in the product line START Pad The START pad is used to begin a manual time entry cooking cycle It is also used to save any changes to programming sequences or user options STOP RESET pad The STOP RESET pad stops a cooking sequence in progress clears out any remaining ti
20. operly and life of electrical parts is reduced B Allow at least 2 5 1 cm between air discharge on back of oven and back wall C Allow at least 2 5 1 cm of clearance around sides of oven No metal pans So how do I use t Mechanical Dial Open oven door place food in oven and close oven door 2 Turn time entry knob clockwise to desired time e Cooking time can be set up to 6 minutes e Oven begins operation and time counts down 38 When cooking time has elapsed microwave energy stops and oven signal sounds Interrupting Operation Open oven door to interrupt operation or turn time entry knob counterclockwise to ge To resume microwave oven operation close door and turn knob Changing Time and Canceling Mistakes Heating time can be changed at any time while the oven is operating Turn knob to desired new setting To set cooking time to zero turn knob counterclockwise to 0 Digital Dial Operation Digital Dial option is available on some models only So how do I use it Digital Dial Heating 1 Open oven door place food in oven and close oven door 2 Turn time entry knob clockwise until desired time displays 30 QUICK SET Pad Allows you to reheat for 30 seconds at 100 full power by simply pressing the 30 QUICK SET pad By repeatedly pressing this pad you can extend the reheating time to 5 minutes by 30 second increments To change the time assigned to this pa
21. or double pad programming see the User Option section Canceling Mistakes If oven is not cooking press STOP RESET pad to clear display If oven is cooking press STOP RESET pad once to stop oven then again to clear display If oven door is open and time shows in display close oven door and press STOP RESET pad to clear display QTY 2X ae Programming some models This feature allows a preset percentage of original cook time called a cooking factor to be added to a cook sequence Programming Multiple Stages some models Stage cooking allows consecutive cooking cycles without interruption Up to four different cooking cycles can be programmed into a memory pad To use stage cooking Follow steps 1 through 5 above Programming Pads Press TIME ENTRY pad e Display briefly shows the pad number that is being programmed and the stage number to the upper right e Display changes to cook time and power level for the next stage Enter cook time and power level as in steps 4 and 5 above Programming Pads e To enter another cooking stage for that pad press TIME ENTRY pad again e Up to four different stages can be programmed Press START pad to set new programming changes to the pad Press STOP RESET pad or close oven door to exit programming mode To change the cooking factor 1 Open oven door Press and hold pad 1 for approximately 5 seconds Press pad to be reprogrammed Press the QTY 2X pad
22. orten life of electrical parts a grounding plug The plug must be e Do not block or obstruct oven filter Allow access for cleaning plugged into an outlet that is properly e Install oven on level countertop surface installed and grounded e Place warning label in a conspicuous place close to microwave oven e Outlet should be located so that plug is accessible when oven is in place Consult a qualified electrician or servicer if grounding instructions are not completely understood or if doubt exists as to whether the oven is properly grounded Do not use an extension cord If the product power cord is too short have a qualified electrician install a three slot receptacle This oven should be plugged into a separate circuit with the electrical rating as provided in product specifications When a microwave oven is on a circuit with A For North American UL CSA models allow at least 2 5 1 cm of clearance around top of oven For International 50 Hz models allow at least 12 30 cm of other equipment an increase in clearance around top of oven Proper air flow around oven cools electrical cooking times may be required and components With restricted air flow oven may not operate properly and life of fuses can be blown electrical parts is reduced B Allow at least 2 5 1 cm between air discharge on back of oven and back wall C Allow at least 2 5 1 cm of clearance around sides of oven External Equipote
23. ted below 1 Record number shown 2 Unplug oven wait for 1 minute and plug in oven Disconnecting electrical supply may eliminate service code If failure continues contact an authorized ACP servicer or call ACP toll free at 1 866 426 2621 inside the U S A or Canada Place one cup of water in oven Run for one minute at full power 100 If tem perature does not rise oven is not operating correctly Contact an authorized ACP servicer or call ACP toll free at 1 866 426 2621 inside the U S A or Canada CLEAN FILTR some models This oven displays CLEAN FILTR every 7 days When the message displays clean the air filter thoroughly Cleaning the air filter will not shut off the message The message w ill stop displaying automatically after 24 hours Call SERV some models Part No 12804501 Revised 8 10 A problem has been detected with the cooking performance of the oven Continue to use the oven but verify food temperatures Call an authorized ACP servicer to correct the problem For full product documentation visit www acpsolutions com 14 2010 ACP Inc Cedar Rapids lowa 52404
24. ts adding heating time while oven is heating Add Time During Allows heating time to be changed while oven is Heating heating when a memory pad is pressed 6 Allows oven to resume heating time countdown after door 730 QUICK SET Reset Door Open Commercial is opened during cycle Cancels heating time count down after door is opened during cycle 12 7 OP 70 Allows 60 minutes of heating time some models OP 71 Allows 10 minutes of heating time Maximum Heating Time 0 OP 00 Do not display message Clean Filter Message OP 01 Display message for 24 hours every 7 days OP 02 Display message for 24 hours every 30 days OP 03 Display message for 24 hours every 90 days Care and Cleanin SP Oven Light Disconnect electrical supply 5 Remove screw from light To avoid electrical shock which access panel located on side can cause severe personal panel of oven Light Bulb injury or death unplug power 3 Turn light bulb cord or open circuit breaker to counterclockwise to remove oven before cleaning or 4 Replace light bulb Do not A removing light bulb over tighten bulb Back of Oven Over tightening may make bulb difficult to remove later 5 Replace light access cover before use Reconnect power supply Light Access Panel Removing Splatter Shield Splatter shield keeps top of microwave oven cavity and antenna from becoming soiled Clean soil from shield with damp cloth or clean with mild detergent and water
25. wer If stage cooking is desired press TIME ENTRY pad and repeat steps 3 through 4 some models e Display changes to cook time and power level for the next stage Enter cook time and power level as in steps 3 and 4 e To add another cooking stage press TIME ENTRY pad again e Up to four different stages can be programmed Press START pad e Oven operates and time counts down e POWER COOK LEVEL and cooking time display At end of cooking cycle oven beeps and shuts off MEDIUM 30 Programmed Pads To cook food using pads preprogrammed with cooking sequences 1 2 Open oven door and place food in oven Close door e READY displays Fan and light will turn on Press desired pad e For single pad entry press only one pad e For double pad entry press the two pads in order of the double digit number for the desired cooking e To change single or double pad entry option see User Options section in this manual Oven begins to cook e POWER power level and total cooking time display If power level does not display microwave is cooking at full power e For additional cooking time press preprogrammed pad again to begin cooking sequence again At end of cooking cycle oven beeps and shuts off Factory Settings Time Pad 1 30 min 2 min 3 min 4 min 5 min Programming the Oven Control Electronic Control The display shows PROGRAM When set to single pad or doubl
Download Pdf Manuals
Related Search