Extender
Contents
1. Gefen Extender for DMI 1 3 over ne Fiber with IR EXT HDMI1 3 1FO User Manual ww gefen com ASKING FOR ASSISTANCE Technical Support Telephone 818 772 9100 800 545 6900 Fax 818 772 9120 Technical Support Hours 8 00 AM to 5 00 PM Monday through Friday Pacific Time Write To Gefen LLC c o Customer Service 20600 Nordhoff St Chatsworth CA 91311 www gefen com support gefen com Notice Gefen LLC reserves the right to make changes in the hardware packaging and any accompanying documentation without prior written notice HDMI the HDMI Logo and High Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing in the United States and other countries Extender for HDMI 1 3 Over One Fiber with IR is a trademark of Gefen LLC 2011 Gefen LLC All rights reserved All trademarks are the property of their respective owners Rev AG CONTENTS Introduction Operation Notes Features Sender Unit Layout Sender Unit Descriptions Receiver Unit Layout Receiver Unit Descriptions Connecting and Operating the Extender Wiring Diagram DIP Switch Configuration DIP Switches Local EDID External Pass Through EDID Modes Deep Color Calibration Procedure Specifications Warranty INTRODUCTION Congratulations on your purchase of the Extender for HDMI 1 3 Over One Fiber with IR Your complete satisfaction is very important to us Gefen Gefen delivers innovat2. 3 Copper cables are limited to a 30 day warranty and cables must be in their original condition The information in this manual has been carefully checked and is believed to be accurate However Gefen assumes no responsibility for any inaccuracies that may be contained in this manual In no event will Gefen be liable for direct indirect special incidental or consequential damages resulting from any defect or omission in this manual even if advised of the possibility of such damages The technical information contained herein regarding the features and specifications is subject to change without notice For the latest warranty coverage information refer to the Warranty and Return Policy under the Support section of the Gefen Web site at www gefen com PRODUCT REGISTRATION Please register your product online by visiting the Register Product page under the Support section of the Gefen Web site 13 FOx 3 1 MA HDMI1 Qu This product uses UL listed power supplies 20600 Nordhoff St Chatsworth CA 91311 1 800 545 6900 WWW gefen com Ex 818 772 9100 amp Rev AG fax 818 772 9120 support gefen com Ce ay
3. switch 3 to the ON position on both the Sender Unit and the Receiver Unit to lock the calibration settings NOTE If the fiber optic cable is changed repeat the calibration procedure Troubleshooting Procedure e Sender Unit and Receiver Unit did not complete the calibration process the indicator LEDs on both Sender Unit and Receiver Unit will be red Check the fiber connections carefully and cycle the power on both the Sender Unit and the Receiver Unit and repeat the calibration procedure When the indicator LED at one unit is GREEN and the other is RED cycle power on the unit with the RED indicator It is also recommended to cycle power on both the Sender Unit and the Receiver Unit to perform a full calibration e Ifthe calibration procedure continues to fail contact Gefen Technical Support under the Asking For Assistance section at the beginning of this manual 11 SPECIFICATIONS Video AmplitierBandWialn euere 225 MHz Maximum Resolutions Supported 1080p60 1920x1200 2K Input Video Signal NIRE 1 2 Volts p p IHBULDDE ee EE 5 Volts p p TTL HDMI Input Output Connector Type A 19 pin RS 232 Input Output eat E DB9 RS 232 Data Transmission Rate 115 200 kbps max LED Indicator Power ON OFF 2 color LED red green LED Indicator Fiber Calibration
4. 2 color LED red green IR Modulation FFEQUENGY sitas iaa di 38 KHz RET 3 5mm Mini Stereo LINK SC Fiber Optic x 1 cable O 5V DC OW CPEs Ol SUDO UN it 10W per unit max Blat le CC 4 2 W x 1 2 x 3 8 D onIDDIndg Weight A PIE PP O RE O O 5 lbs Compliancy RoHS and CE Certified Complies with US EU Standards HDMI 1 3 HDMI 1 2 HDCP 1 1 and DVI 1 0 Compliant UL Certified Power Supply 12 WARRANTY Gefen warrants the equipment it manufactures to be free from defects in material and workmanship If equipment fails because of such defects and Gefen is notified within two 2 years from the date of shipment Gefen will at its option repair or replace the equipment provided that the equipment has not been subjected to mechanical electrical or other abuse or modifications Equipment that fails under conditions other than those covered will be repaired at the current price of parts and labor in effect at the time of repair Such repairs are warranted for ninety 90 days from the day of reshipment to the Buyer This warranty is in lieu of all other warranties expressed or implied including without limitation any implied warranty or merchantability or fitness for any particular purpose all of which are expressly disclaimed 1 Proof of sale may be required in order to claim warranty 2 Customers outside the US are responsible for shipping charges to and from Gefen
5. EN EXTENDER FOR HDMI 1 3 OVER ONE FIBER WITH IR How to Connect the Extender for HDMI 1 3 over One Fiber with IR 1 Connect a Hi Def source to the Sender Unit using the included Locking HDMI cable Connect the HDTV display to the Receiver Unit with a user supplied HDMI cable 2 Connect an SC terminated fiber optic cable to the Sender Unit Connect the opposite end of the fiber cable to the Receiver Unit 3 OPTIONAL Connect an RS 232 cable from the RS 232 serial port on the controlling device to the RS 232 port on the Sender Unit Connect another RS 232 serial cable from the RS 232 port on the Receiver Unit to the RS 232 port of the RS 232 device 4 IMPORTANT Before connecting the power supplies to the Sender Unit and the Receiver Unit see page 11 for information on calibrating the Sender Unit and Receiver Unit After the Sender Unit and Receiver Unit have been properly calibrated a vibrant HDTV HD picture will be seen along with multichannel digital audio if the display supports audio Wiring Diagram for the Extender for HDMI 1 3 over One Fiber with IR SC SC FIBER OPTIC CABLE su HDMI CABLE Fees RS 232 e IR umm IR Emitter IR Extender N Hi Def Source T 9 RS 232 Controller Sender HD Display with RS 232 Control EXT HDMI 1 3 1FO DIP SWITCH CONFIGURATION DIP Switches On the bottom of the Sender Unit and Receiver Unit are a bank of four 4 DIP switches These DIP sw
6. Uses widely available single strand multi mode SC fiber optic cable e Immune to electromagnetic interference EMI e HDCP Compliant Package Includes 1 Extender for HDMI 1 3 Over One Fiber with IR Sender unit 1 Extender for HDMI 1 3 Over One Fiber with IR Receiver unit 2 Mounting Plates 1 6 ft HDMI Cable M M 1 6 ft DB9 Serial Cable M F 2 5V DC Locking Power Supplies 1 User Manual SENDER UNIT LAYOUT Front Back SENDER UNIT DESCRIPTIONS Power Indicator This two color LED will turn bright red once the included 5V DC locking power supply has been properly connected to the unit and the locking power supply has been connected to an available wall outlet This LED will turn bright green once the Sender unit and Receiver unit are communicating correctly Calibration Indicator This LED will alternate from red to green during the calibration procedure The LED will turn solid green once the calibration procedure has been completed IR Blaster Port Connect an IR Blaster cable Gefen part EXT 2IREMIT to this port Locking HDMI Input Port Connect a Hi Def source to this HDMI port RS 232 Input Port Connect the controlling device to this port Fiber Optic Connector SC Type This connector accepts 1 strand of SC terminated fiber optic cable that will link the Sender Unit and Receiver Unit together The Gefen Extender for HDMI 1 3 Over One Fiber with IR will only accept multi mode fiber op
7. h the Sender Unit and the Receiver Unit A clean and vibrant HDMI A V signal will appear on the display along with clear and crisp digital audio Send IR commands from the IR Remote Control back to A V source equipment via the IR back channel using the fiber optic cable connecting the Sender Unit to the Receiver Unit The Sender Unit has an IR blaster port enabling wide IR signal coverage in an A V equipment room In addition RS 232 commands from a home automation system or PC can be used to control the source device or any other RS 232 device using the ports on the Sender Unit and the Receiver Unit OPERATION NOTES READ THESE NOTES BEFORE INSTALLING OR OPERATING THE EXTENDER FOR HDMI 1 3 OVER ONE FIBER WITH IR e IR data repeater functionality is single directional IR data can only transmitted from the Receiving unit back to the Sending unit IR data cannot be transmitted from the Sending unit to the Receiving unit e Use one SC terminated multi mode fiber optic cable to operate the HDMI 1 3 Over One Fiber with IR e 1080 video may be extended up to 1000 feet 300m depending on the type of fiber optic cable used The following maximum extension distances will be possible depending on the types of fiber optic cabling that are used e 100m 330 ft on 62 5 125 um OM1 multi mode SC fiber e 300m 1000 ft on 50 125 um multi mode SC fiber RS 232 data is bi directional for direct commands and echo function s
8. itches provide control over EDID Deep Color and unit Calibration Remove the strip of tape to expose the DIP switches To change the DIP switch settings move the appropriate DIP switch to its ON or OFF position using a small pointed object The DIP switches and their functions are shown below ON OFF Sender Unit DIP switches Receiver Unit DIP switches Calibration Mode On OFF or Lock ON DIP SWITCH CONFIGURATION DIP 1 EDID Mode OFF Local EDID When Local EDID mode is used the EDID will be assembled by copying all video and audio features of the connected device Deep Color support will be manually controlled If Deep Color is supported by the display s DIP 2 should be set to the ON position see DIP 2 Deep Color below By default the unit is shipped with DIP 1 in the OFF position ON Pass Through EDID Allows all video and audio features of the connected devices to be passed to the source device without control over Deep Color DIP 2 Deep Color NOTE DIP switch 2 is only functional when DIP switch 1 is set to the OFF posi tion OFF Enables Deep Color support 12 bit color Enables Deep Color support In Pass through EDID Mode setting DIP2 OFF has no effect since all EDID information is passed through ON Forces 8 bit Color Disables Deep Color in the EDID Deep Color management is only available when Local EDID is being used DIP 3 Calibration Mode OFF Enables Ca
9. ive progressive computer and electronics add on solutions that harness integration extension distribution and conversion technologies Gefen s reliable plug and play products supplement cross platform computer systems professional audio video environments and HDTV systems of all sizes with hard working solutions that are easy to implement and simple to operate The Gefen Extender for HDMI 1 3 Over One Fiber with IR The Gefen Extender for HDMI 1 3 Over One Fiber with IR transmits 1080p Full HD in Deep Color and multi channel digital audio up to 1000 feet 330 meters over a single strand SC fiber optic cable Extraordinary distances can be achieved using this feature rich device 1080p Full HD with Deep Color is instantaneously displayed at the remote location This product also eliminates EMI electromagnetic interference picture cut outs and screen distortions traditionally seen with copper based HDMI extenders A multi channel digital audio experience is delivered with Dolby TrueHD and DTS HD Master A single strand SC fiber cable carries the IR back channel and bidirectional RS 232 facilitating convenient local control of the video source devices How It Works Connect the Sender Unit to the high definition source using the provided HDMI cable Connect the Receiver Unit to an HDTV display using another HDMI cable Run a single strand of SC fiber optic cable from Sender Unit to the Receiver Unit Power up bot
10. libration Mode Enables Calibration Mode Make sure to set DIP switch 3 on both the Sender Unit and Receiver Unit when calibrating the Extenders See page 11 for details ON Calibration Mode Lock Locks the calibration settings Set DIP switch 3 on both the Sender Unit and Receiver Unit to the ON position after the calibration process has completed See page 11 for details on the calibration process 10 DIP SWITCH CONFIGURATION Calibrating the Sender Unit and Receiver Unit IMPORTANT Before beginning the calibration process make sure that the Sender Unit and Receiver are not powered 1 Make sure DIP switch 3 on both the Sender Unit and the Receiver Unit are in the OFF position see page 9 2 Connect one end of the fiber cable to the Sender Unit Connect the other end of the fiber cable to the Receiver Unit 3 Make sure DIP switch 3 on both the Sender Unit and the Receiver Unit are in the OFF position see page 9 4 Connect the 5V DC Locking Power Supplies to the Sender Unit and the Receiver Unit Do not overtighten the locking connectors Plug the power cord into an available electrical outlet The LED indicators on both the Sender Unit and Receiver Unit will alternate from red to green during the calibration process The calibration process can take up to 120 seconds to complete After the calibration process has finished the LED indicators on both the Sender unit and the Receiver unit will turn solid green Set DIP
11. tatus information IMPORTANT CALIBRATION PROCEDURE These steps must be followed when setting up the Gefen Extender for HDMI 1 3 over one Fiber with IR for the first time e Connect the SC fiber optic cable between the Sender unit and the Receiver unit e Set DIP switch 3 on both the Sender unit and the Receiver unit to the OFF position e Apply power to the source and to both the Sender and Receiver units The LED indicators on both the Sender unit and Receiver unit will alternate from red to green during the calibration process The calibration process can take up to 120 seconds to complete e After the calibration process has finished the LED indicators on both the Sender unit and the Receiver unit will be solid green Set DIP switch 3 to the ON position on both the Sender unit and the Receiver unit to lock the calibration settings NOTE When changing fiber optic cables the calibration procedure must be repeated See page 11 for details on the calibration procedure FEATURES HDMI 1 3 Features e 225 MHz up to 12 bit YUV 444 1080p e Deep Color e Dolby TrueHD and DTS HD Master Audio e Lip Sync e Protocol Pass Through Features e Supports video resolutions up to 1080p 1920 x 1200 and 2K e Pass Through e Delivers highest quality signal of any HDMI extension method e EDID Detection Adjustment for rapid integration of source and displays e Extends HDMI and RS 232 up to 1000 feet 300m e
12. tic cabling 5V DC Locking Power Connector Connect the included 5V DC Locking Power Supply to this receptacle RECEIVER UNIT LAYOUT Front Back RECEIVER UNIT DESCRIPTIONS RS 232 Output Port Connect a controlling device to this port Locking HDMI Output Port Connect a HDTV display to this HDMI port IR Window Receives signals from the Hi Def source IR remote control unit The IR signals are sent back to the source device when using an IR Blaster Calibration Indicator This LED will alternate from red to green during the calibration procedure The LED will turn solid green once the calibration procedure has been completed Power Indicator This two color LED will turn bright red once the included 5V DC locking power supply has been properly connected to the unit and the locking power supply has been connected to an available wall outlet This LED will turn bright green once the Sender unit and Receiver unit are communicating correctly 5V DC Locking Power Connector Connect the included 5V DC Locking Power Supply to this receptacle IR Extender Port Connect an IR Extender cable Gefen part EXT RMT EXTIR to this port Fiber Optic Connector SC Type This connector accepts 1 strand of SC terminated fiber optic cable that will link the Sender Unit and Receiver Unit together The Gefen Extender for HDMI 1 3 Over One Fiber with IR will only accept multi mode fiber optic cabling CONNECTING AND OPERATING THE GEF
Download Pdf Manuals
Related Search