User Manual
Contents
1. Tire size Dimensions LxWxH Weight AW32 hydraulic fluid for operation over 40 F Dexron automatic transmission fluid for below 40 F 2 8 quarts 18 inch 6 inch 38 1 4x11x18 inch 99 Ibs SAFETY INFORMATION Please read and understand this entire manual before attempting to assemble operate or install the product These safety instructions are not meant to cover every possible condition that could occur If you have any questions regarding the product please call customer service at 1 800 232 1195 8 00 a m 5 00 p m CST Monday Friday Safety Signals The purpose of safety signal statements and symbols is to attract your attention to possible danger Read them carefully to understand and practice proper accident prevention dh DANGER Signals an EXTREME hazard Failure to obey a safety DANGER signal WILL result in serious injury or death to yourself or to others Always follow the safety precautions to reduce the risk of fire electric shock and personal injury dh WARNING Signals a serious hazard Failure to obey a safety WARNING signal CAN result in serious injury to yourself and to others Always follow the safety precautions to reduce the risk of fire electric shock and personal injury dh CAUTION Signals a moderate hazard Failure to obey a safety CAUTION signal MAY result in property damage or personal injury to yourself or to others Always follow the safety precautions to reduce the risk of fire electric sh2. 1 could break resulting in severe eye injury FORESIGHT 18 ka THAN NO SIGHT SPECIFIC SAFETY RULES FOR LOG SPLITTER 1 IF YOU ARE NOT thoroughly familiar with the operation of the log splitter obtain instruction from a qualified person 2 MAKE SURE wiring codes and recommended electrical connections are followed When servicing use only identical replacement parts Disconnect log splitter from the power source before making adjustments or repairs 3 Place the log splitter on a stable flat and level work surface where there is plenty of room for handling logs 4 INSPECT THE LOG SPLITTER before each use Keep guards in place and in working order Replace damaged missing or failed parts before using 5 Do not alter the log splitter Altering the tool or exceeding its design capabilities and capacities could result in serious injury or fatality and will void the warranty 6 MAKE SURE THE EXTENSION CORD is no longer than 25 ft 14 gauge Ensure the power cord is rated for outdoor use Ground the log splitter and avoid contact with grounded surfaces during operation See Electrical Information for further details 7 MAKE all adjustments with the switch in the OFF position and the log splitter disconnected from the power source 8 Never use the log splitter for any other purpose than splitting wood Any other use can result in injury Use extreme caution at all times 9 PREPARE LOGS FOR SPLITTING Make sure the ends o
3. is low jerky makes There may be air in the hydraulic Loosen the bleed screw one or two unfamiliar noise or vibration system rotations 17 EXPLODED VIEW AND PARTS LIST 18 Item Stock Description 1 56206 001 Motor 2 56206 002 Nut M6 3 56206 003 Rubber foot 4 56206 004 Right rubber foot 5 56206 005 bolt M6x12 6 56206 006 Left rubber foot 7 56206 007 Nut M8 8 56206 008 Washer 9 56206 009 Bearing bush 10 56206 010 Claboard 11 56206 011 Steel ring10 12 56206 012 Gear 13 56206 013 Gear shaft 14 56206 014 Steel ball 2 5 15 56206 015 Round pin 2 5x4 16 56206 016 Bolt M8x30 17 56206 017 Spring washer 8 18 56206 018 Flat washer 8 19 56206 019 Bolt M8x55 20 56206 020 Shaft 21 56206 021 Cover 22 56206 022 Oil seal 10x2 65G 23 56206 023 Bolt M6x12 24 56206 024 Spring washer 6 25 56206 025 Flat washer 6 26 56206 026 Locking nut M10 27 56206 027 Flat washer 10 28 56206 028 Wheel 29 56206 029 Wheel shaft 30 56206 030 Pin3 2x20 19 Item Stock Description 31 56206 031 Bracket 32 56206 032 Bolt 33 56206 033 Rubber sleeve 34 56206 034 Hydraulic control lever 35 56206 035 Nut M10 36 56206 036 Nut M10 37 56206 037 Spring was
4. tool is equipped with an electric cord that has a POLARIZED plug The plug MUST be plugged into a matching outlet that is properly installed and grounded in accordance with ALL local codes and ordinances DO NOT MODIFY THE PLUG PROVIDED If it will not fit the outlet have the proper outlet installed by a qualified electrician dh CAUTION IN ALL CASES MAKE CERTAIN THE RECEPTACLE IN QUESTION IS PROPERLY GROUNDED IF YOU ARE NOT SURE HAVE A CERTIFIED ELECTRICIAN CHECK THE RECEPTACLE dh WARNING IMPROPER USE OF EXTENSION CORDS MAY CAUSE INEFFICIENT OPERATION WHICH CAN RESULT IN OVERHEATING USE AN EXTENSION CORD RATED FOR OUTDOOR OPERATION GUIDELINES FOR USING EXTENSION CORDS USE THE PROPER EXTENSION CORD Make sure your extension cord is in good condition When using an extension cord be sure to use one of heavy enough gauge to carry the current your product will draw An undersized cord will cause overheating The table below shows the correct size to use depending on cord length and nameplate ampere rating If in doubt use the next heavier gauge The smaller the gauge number the heavier the cord Minimum Gauge for Extension Cords AWG When using 120 V only Ampere Rating Total Length of Cord in feet More Than Not More 25 50 100 150 Than 0 6 18 16 16 14 6 10 18 16 14 12 10 12 16 16 14 12 12 16 14 12 Not Recommended Make sure your extension cord is prope
5. work This will provide a safer less cluttered work area ELECTRICAL INFORMATION A WARNING TO AVOID ELECTRICAL HAZARDS FIRE HAZARDS OR DAMAGE TO THE TOOL USE PROPER CIRCUIT PROTECTION THE LOG SPLITTER IS WIRED AT THE FACTORY FOR 120 V OPERATION CONNECT TO A 120 V 15 A CIRCUIT AND USE A15 A TIME DELAYED FUSE OR CIRCUIT BREAKER TO AVOID SHOCK OR FIRE IMMEDIATELY REPLACE THE POWER CORD IF IT IS WORN CUT OR DAMAGED IN ANY WAY Fig A This log splitter has a 3 prong plug that is intended for use on a Fool as PA circuit that has a receptacle like the one illustrated in Fig 1 Us j aa Do not modify the power cord plug If it does not match the ENS 2 electrical outlet have the proper outlet installed by a qualified 3 electrician 1 3 pronged plug 2 grounding prong 3 properly grounded outlet WARNING TO AVOID INJURY USE ONLY IDENTICAL REPLACEMENT PARTS WHEN SERVICING THE LOG SPLITTER WARNING DO NOT TOUCH THE METAL BLADES ON THE POWER CORD PLUG WHEN REMOVING OR INSTALLING THE PLUG INTO AN ELECTRICAL OUTLET OR EXTENSION CORD di WARNING TO AVOID ELECTROCUTION 1 Use only identical replacement parts when servicing this tool Servicing should be performed by a qualified technician 2 Do not use in wet or damp areas or expose to rain GROUNDING INSTRUCTIONS IN THE EVENT OF A MALFUNCTION OR BREAKDOWN grounding provides the path of least resistance for electrical current and reduces the risk of electric shock This
6. 3 56206 083 Piston 84 56206 084 stud 85 56206 085 stud 86 56206 086 Spring 87 56206 087 Rear cover 88 56206 088 Oil seal 3 6x1 8G 89 56206 089 Bleed screw 90 56206 090 Oil seal30x2 65G 91 56206 091 Washer FC30x38x5 92 56206 092 Dipstick 93 56206 093 Oil seal 11 8x2 65G 94 56206 094 Knob 95 56206 095 Piston rod 96 56206 096 lock nut M14 20 TWO YEARS LIMITED WARRANTY WEN log splitters are warranted to the original purchaser to be free from defects in materials and workmanship for a period of two 2 years from the date of original purchase Log splitters used for commercial or for rental have a warranty period of 90 days from date of original purchase Please fill out and mail the enclosed warranty card and mail it to Power Pro Technology along with a copy of the receipt The information is required to process warranty claims WEN will repair or replace at its discretion any part that is proven to be defective in materials or workmanship under normal use during the two 2 year warranty period Warranty repairs or replacements will be made without charge for parts or labor Parts replaced during warranty repairs will be considered as part of the original product and will have the same warranty period as the original product TO EXERCISE WARRANTY COVERAGE Do not return to retailer For warranty and technical support call the toll free Customer Service Number 800 232 1195 and you will be in
7. HE SEALS AND PERMANENTLY DAMAGE THE LOG SPLITTER 1 Turn the bleed screw 1 counterclockwise one or two turns to allow air to be released from the hydraulic system Note A flow of air through the bleed screw should be detectable while the log splitter is in use 2 Close the bleed screw after operation Note Check the bleed screw and make sure it is closed before and during transporting the log splitter to and from the jobsite and storage area Hydraulic fluid may leak through the bleed screw opening if the bleed screw is not fully tightened Failure to loosen the bleed screw will cause pressure to build up in the hydraulic tank and could damage the seals and affect the operation of the log splitter Place a log on the log splitter WARNING NEVER TRY TO SPLIT LOGS LARGER THAN THE RATED CAPACITY OF THE TOOL ATTEMPTING TO DO SO COULD RESULT IN PERSONAL INJURY AND DAMAGE TO THE TOOL Select prepare a log for splitting 1 Make sure there are no nails or foreign objects in the log 2 Make sure the end of each log to be split is square 3 Remove any branches by cutting them flush with the trunk 4 Make sure each log is no longer than 21 in and the diameter is 10 in or less Place a properly prepared log firmly on the worktable between the two worktable guards The log should fit between the ram and the splitting wedge 13 Operate the log splitter Fig 6 1 Ensure the equipment is in safe working condition Oper
8. ING Select a work area Place the log splitter on a flat stable surface Make sure there is sufficient room for the unsplit logs and for the stacks of split logs Make sure there is a safe electrical connection no more than 25 ft from the work area Checking the hydraulic fluid level Fig 4 This log splitter has been filled with AW32 hydraulic oil at the factory Warning Lifting the log splitter is a two person operation Once raised make sure the log splitter is stable before performing any maintenance 1 Lift up on the handle of the log splitter Make sure the splitter is resting securely and will not fall Loosen the fluid drain knob 1 Pull out the bolt with attached dipstick Wipe the fluid off the dipstick Put the dipstick back in the fluid tank and then pull it out again Check the fluid level It should be between the two notches 2 near the end of the dipstick Add fluid if needed See below for types Replace the dipstick and tighten the fluid drain knob Hydraulic fluid Use an AW32 hydraulic fluid for operation over 40 F a Oy Ore GS Dexron automatic transmission fluid for operation below 40 F Note Do not mix AW32 hydraulic fluid with Dexron automatic transmission fluid 12 Loosen the bleed screw Fig 5 WARNING ALWAYS LOOSEN THE BLEED SCREW PRIOR TO OPERATION THIS WILL REMOVE ANY AIR TRAPPED IN THE HYDRAULIC SYSTEM FAILURE TO RELEASE AIR FROM THE HYDRAULIC SYSTEM MAY DAMAGE T
9. OPERATOR S MANUAL 6 Ton Electric Log Splitter Model 56206 IMPORTANT Your new WEN tool equipment has been engineered and manufactured to high standards for dependability ease of operation and operator safety Properly cared for it will give you years of rugged trouble free performance Pay close attention to the Rules for Safe Operation and Warnings If you use your tool equipment properly and only for what it is intended you will enjoy years of safe reliable service It s not how it s WEN the project get s done Contact us for product questions or technical support t WenProducts com 800 232 1195 M F 8 5 CST 2 techsupport wenproducts com TABLE O F CONTENTS Product specifications Safety information General safety lesa See Specific safety rules for log splitter Electrical information Knowsour l s splitten preke Package contents ASSEDIO REI ase AGO Operation ee Maintenance Troubleshooting Exploded view and parts list i pra nil luianaellialai Warranty PRODUCT SPECIFIATIONS Model Splitting force Cycle time Motor Motor speed Power cord 56206 6 Tons 25 seconds 120 V A C 60 Hz 15 A 2 HP 1500W 3400 RPM 6 feet SITW 14 AWG Log capacity Diameter 10 inch Length 20 5 inch Hydraulic pressure 3000 psi Hydraulic fluid Hydraulic tank capacity Cylinder stroke
10. ate the unit without loading to make sure it is working normally Check all nuts bolts and hydraulic fittings are tight Check the switch power cable and plug for damage to avoid electric shock 2 Plug in the power cable NEVER use an extension cord longer than 25 feet Minimum cord gage must be 16 The power supply for this log splitter must have a protection device circuit breaker for over or under voltage 3 Place a log on the beam against the ram Make sure that the log is securely on the beam and up against the ram Logs should be cut with square ends and to a maximum length of 20 5 inch in advance Always use extra care when splitting logs with unsquare ends 4 Loosen the bleed screw one or two turns if necessary 5 Two controls must be activated to operate the log splitter The hydraulic control lever 1 and the ON OFF push button 2 must be held during the splitting process If either control is released the log splitter will stop operating 6 Depress and hold the ON OFF push button 2 with your right hand and allow the motor to cycle up to speed 7 Push down on the hydraulic control lever 1 8 Release the ON OFF button and the control lever when the log is split The push rod will then retract dh Warning If the log does not begin to split after 5 seconds of operation release both controls The motor or hydraulic fluid may overheat and damage the machine A Warning Do not attempt to remove a jammed log with y
11. e stop 11 DISCONNECT THE POWER Unplug the tool when not in use before making adjustments changing parts cleaning or working on the tool 12 DO NOT OVERREACH Keep proper footing and balance at all times A WARNING Some dust created by power sanding sawing grinding drilling and other construction activities contains chemicals known to the State of California to cause cancer birth defects or other reproductive harm Some examples of these chemicals are e Lead from lead based paints e Crystalline silica from bricks and cement and other masonry products and e Arsenic and chromium from chemically treated lumber Your risk from these exposures varies depending on how often you do this type of work To reduce your exposure to these chemicals work in a well ventilated area and work with approved safety equipment always wear MSHA NIOSH approved properly fitting face mask or respirator when using such tools 13 MAINTAIN TOOLS PROPERLY ALWAYS keep tools clean and in working order 14 CHECK FOR DAMAGED PARTS Check for alignment of moving parts binding breakage or any other conditions that may affect the tool s operation Any part that is damaged should be properly repaired or replaced before use Only wear safety goggles that apply with ANSI Z87 1 When operating power tools foreign objects can be thrown into your eyes This could result in permanent eye damage Glasses or goggles that are not in compliance with ANSI Z87
12. f the logs are cut square Cut off any branches flush with the trunk 10 INSPECT EACH LOG before splitting Make sure there are no nails or foreign objects in the log 11 Only a single operator should load and operate the log splitter Keep all others including children and pets a minimum of 20 feet away from the work area 12 NEVER TRY TO SPLIT LOGS larger than the rated capacity of the tool Attempting to do so could result in personal injury and damage to the tool 5 13 Split only one log at a time Do not attempt to split two logs on top of each other 14 DO NOT put your hands or feet between the log and the splitting wedge or between the log and the push rod while the tool is in operation dh WARNING KEEP HANDS AWAY FROM SPLITS AND CRACKS WHICH OPEN IN THE LOG THEY MAY CLOSE SUDDENLY AND CRUSH OR AMPUTATE YOUR HANDS 15 Do not attempt to load a log while the push rod is in motion When loading place your hands on the sides of the log not on the ends 16 WAIT FOR THE PUSH ROD TO STOP MOVING before loading another log onto the log splitter Do not try to remove a split log until the entire splitting cycle is completed 17 Use only your hands to operate the control lever Never use your foot knee rope or extension device 18 Never use your hands to remove a jammed log If a jam should occur release the ON OFF push button Follow the instructions in this manual for removing a jammed log 19 Stack logs as you
13. formed of the nearest authorized service center We will prearrange the repair with the center WARRANTY COVERAGE This warranty is conveyed to the original purchaser and is not transferable Log splitters contain parts that will wear out with usage and parts that need maintenance The warranty does not cover wear or maintenance parts Specifically the warranty does not cover hydraulic fluid Warranty does not extend to log splitters damaged or affected by accidents neglect misuse contaminated fuel unauthorized alterations use in applications beyond product design and any other modification or abuse WEN is not liable for any indirect incidental or consequential damages from the sale or use of this product Any implied warranties are limited to two 2 years as stated in this written limited warranty Some states do not allow limitation on the length of an implied warranty Some states do not allow the exclusion or limitation of incidental or consequential damages This warranty gives you the specific legal right and you may have other rights that vary by state For questions comments technical assistance or repair parts Please Call Toll Free at 1 800 232 1195 M F 8am 5pm CST SAVE YOUR RECEIPTS THIS WARRANTY IS VOID WITHOUT THEM WWW WENPRODUCTS COM 21
14. her 10 38 56206 038 Oil seal 9 5x2 65G 39 56206 039 Plastic cover 40 56206 040 BoltM6x20 41 56206 041 Hexagon nut 42 56206 042 Bush for shaft 43 56206 043 Oil seal 4 87x1 8G 44 56206 044 Shaft 45 56206 045 Adjustment spring 46 56206 046 Cone valve 47 56206 047 Oil valve 48 56206 048 Screw 49 56206 049 Oil seal 11 8x2 2G 50 56206 050 Hexagon bolt 51 56206 051 Bolt 52 56206 052 Washerl6xtl 53 56206 053 Oil seal 14x1 8G 54 56206 054 spring II 55 56206 055 Front cover 56 56206 056 Control valve 57 56206 057 Oil seal 11 2x1 8G 58 56206 058 Journey valve 59 56206 059 Oil seal 5 6x1 8G 60 56206 060 Spring I Item Stock Description 61 56206 061 Washer 6 62 56206 062 Washer 63 56206 063 Oil seal 48 7x3 55G 64 56206 064 Nut M6 65 56206 065 Front bracket 66 56206 066 Upper pad 67 56206 067 Push rod 68 56206 068 Tine plate 69 56206 069 Bolt M4x6 70 56206 070 Down pad 71 56206 071 Nut M14 72 56206 072 Rubber plug 73 56206 073 Work table guard 74 56206 074 Back bracket 75 56206 075 Beam 76 56206 076 Step bolt M6x50 77 56206 077 Work table guard 78 56206 078 Rubber handle Item Stock Description 79 56206 079 Bolt M8x50 80 56206 080 Cylinder 81 56206 081 Ring58x52 5x4 82 56206 082 Oil seal43 7x3 55G 8
15. ng the log splitter is a two person operation Once raised make sure the log splitter is Place a 1 Gallon or larger pan 3 under the splitting wedge end of the log splitter Loosen the fluid drain knob 1 and remove it Raise motor end of the log splitter to allow the fluid to drain into the pan Lower motor end of the splitter when it is empty Note Dispose of used fluid properly 4 Raise the splitting wedge end and make sure it is secure 15 6 7 8 Pour approximately 0 85 Gallon of approved hydraulic fluid AW32 hydraulic fluid for operation over 40 F or Dextron automatic transmission fluid for operation below 40 F into the tank Check the fluid level with the dipstick Add more fluid if needed Replace the fluid drain knob 1 and tighten securely Lower the log splitter Hydraulic fluid Use an AW32 hydraulic fluid for operation over 40 F Dexron automatic transmission fluid for operation below 40 F Note Do not mix AW32 hydraulic fluid with Dexron automatic transmission fluid Sharpen the splitting wedge After a period of use the splitting wedge may need to be sharpened Use a fine toothed file or rasp to remove burrs or to refresh crushed areas 16 TROUBLESHOOTING Use this troubleshooting information to remedy problems that may occur during the operation of the log splitter Problem Cause Action Logs will not split Extension cord is too long or gauge is t
16. ock and personal injury NOTE Signals additional important general information GENERAL SAFETY RULES Safety is a combination of common sense staying alert and knowing how to use the log splitter A WARNING TO AVOID MISTAKES THAT COULD CAUSE SERIOUS INJURY DO NOT PLUG IN THE LOG SPLITTER UNTILTHE FOLLOWING STEPS HAVE BEEN READ AND UNDERSTOOD 1 READ and become familiar with this entire instruction manual LEARN the tool s applications limitations and possible hazards 2 AVOID DANGEROUS CONDITIONS DO NOT use in wet or damp areas or expose to rain 3 DO NOT use in the presence of flammable liquids or gases 4 KEEP BYSTANDERS AT A SAFE DISTANCE NEVER allow children or pets near the tool 5 DRESS FOR SAFETY DO NOT wear loose clothing neckties or jewelry rings watches etc when operating tool Inappropriate clothing can get caught and pull you into moving parts 6 ALWAYS WEAR EYE AND FACE PROTECTION 7 ALWAYS remove the power cord plug from the electric outlet when making adjustments changing parts or cleaning 8 AVOID ACCIDENTAL START UPS Make sure the power switch is in the OFF position before plugging in the power cord 9 DO NOT abuse the power cord Keep cord away from heat oil sharp edges or moving parts Replace damaged cord immediately it may create a shock or fire hazard 10 NEVER LEAVE A RUNNING TOOL UNATTENDED Turn the power switch to OFF Do not leave the tool until it has come to a complet
17. oo low Check extension cord to ensure the gauge of the cord is 12or 14 AWG and that the cord length does not exceed 25 ft Incorrect positioning of the log Make sure the log is properly positioned on the worktable See page 13 Place a log on the log splitter The size or hardness or density of the log may exceed the capacity of the splitter Reduce the log size before placing it on the splitter Splitting wedge cutting edge is blunt or dull Sharpen the wedge See page 16 Sharpen the splitting wedge The bleed screw was not loosened and air is trapped in the hydraulic tank Loosen the bleed screw one or two turns The hydraulic fluid is low and may need to be replenished Check the hydraulic fluid level and refill if needed The maximum pressure limiting adjustment setting has changed Contact a trained service Technician at 1 800 232 1195 Hydraulic fluid The bleed screw may not have Tighten the bleed screw leaks been tightened before transporting the splitter The bleed screw may not have Loosen the bleed screw one or two turns been loosened before operation and air is trapped in the hydraulic system The fluid drain knob may be Tighten the knob loose The hydraulic control valve Contact a trained service Technician at 1 assembly and or seals may be 800 232 1195 worn Push rod The hydraulic fluid level may be Check the fluid level and refill if needed movement
18. our hands or try to knock it off the worktable Doing so may cause injury and may also damage the splitting wedge Knock off the log with hammer A When finished splitting the logs unplug the power cord and lock the bleed screw 14 MAINTENANCE WARNING DISCONNECT THE LOG SPLITTER FROM THE POWER SOURCE BEFORE PERFORMING ANY MAINTENANCE Check hydraulic fluid at the beginning of each season and if the fluid level is low Checking the hydraulic fluid level Fig 7 stable before performing any maintenance 1 OD 9 Warning Lifting the log splitter is a two person operation Once raised make sure the log splitter is Lift up on the handle of the log splitter Make sure the splitter is resting securely and will not fall Loosen the fluid drain knob 1 Pull out the bolt with attached dipstick Wipe the fluid off the dipstick Put the dipstick back in the fluid tank and then pull it out again Check the fluid level It should be between the two notches 2 near the end of the dipstick Add fluid if needed See below for types Replace the dipstick and tighten the fluid drain knob Hydraulic fluid Use an AW32 hydraulic fluid for operation over 40 F Dexron automatic transmission fluid for operation below 40 F Note Do not mix AW32 hydraulic fluid with Dexron automatic transmission fluid Replace hydraulic fluid Fig 7 8 stable before performing any maintenance 1 2 3 Warning Lifti
19. rly wired and in good electrical condition 7 Always replace a damaged extension cord or have it repaired by a qualified person before using it Protect your extension cords from sharp objects excessive heat and damp or wet areas Use a separate electrical circuit for your tools This circuit should not be less than 12 gauge cord and should be protected with a 15 A time delayed fuse Before connecting the motor to the power line make sure the switch is in the OFF position and the electric current is rated the same as the current stamped on the motor nameplate Running at a lower voltage will damage the motor A WARNING THE EXTENSION CORD AND RECEPTACLE MUST BE GROUNDED WHILE IN USE TO PROTECT THE OPERATOR FROM ELECTRICAL SHOCK KNOW YOUR LOG SPLITTER 4 3 1 Motor 2 Handle 3 Fluid Drain Fill Knob w Dipstick 4 Bleed Screw must be open during operation 5 Wedge 6 Work Table Guards 7 Hydraulic Control Lever 8 Wheel 9 Circuit Breaker 10 ON OFF Power Switch 11 Ram 12 Beam PACKAGE CONTENTS UNPACKING The log splitter requires the wheel assembly to be attached to the base Please refer to Wheel Assembly on page 11 for assembly directions Note Do not discard box or any packing material until all parts are examined and accounted for This log splitter has been filled with AW32 hydraulic oil at the factory Refer to the photo and parts list should it become necessary to disassemble the unit for repair or replacement of parts In
20. spect it for shipping damage Item List 1 Log Splitter 2 Wheels 1 Wheel Shaft 1 Cotton Pin 2 Washers and 2 Nuts IF ANY PART OF THE LOG SPLITTER IS MISSING OR DAMAGED DO NOT PLUG IN UNTILTHE DAMAGED PART IS REPATRED OR REPLACED PLEASE CALL 1 800 232 1195 FOR ASSISTANCE 10 ASSEMBLY Wheel Assembly 1 Insert the wheel shaft into the frame of the motor end of the log splitter and secure with the cotter pin 2 Secure the wheels to the wheel shaft using the nuts and washers on both side Cotter Pin Washer Nut 11 OPERATION A WARNING Read and thoroughly understand all instructions and safety information before operating this log splitter Failure to do so may cause serious injury or death Do not allow anyone to operate this log splitter who has not read this manual As with all power equipment a log splitter can be dangerous if assembled or used improperly Do not operate this log splitter if you have doubts or questions concerning safe operation Call our customer service department at 1 800 232 1195 to address these concerns WARNING ALWAYS WEAR SAFETY GLASSES SAFETY GLOVES SAFETY SHOES AND SUITABLE WORK CLOTHING WHEN OPERATING THIS LOG SPLITTER NEVER WEAR JEWELRY NECKTIES OR OTHER LOOSE CLOTHING WHICH COULD GET CAUGHT IN MOVONG PARTS A WARNING KEEP HANDS AND FEET CLEAR OF RAM AND WEDGE AT ALL TIMES WARNING KEEP AWAY FROM FLAMMABLE LIQUIDS AND GASES BEFORE STARTING MACHINE BEFORE OPERAT
Download Pdf Manuals
Related Search