Home

Manual

1. o E BS Industrial VOSL2 Extender wide Temp 1 LAN Port 3 LED 2 VDSL 4 DIP Switch Top View The top panel of the Industrial Ethernet to VDSL2 extender is equipped one terminal block connector of two DC power inputs Top Panel of the Industrial Ethernet to VDSL2 extender Wiring the Power Inputs Please follow the steps below to insert the power wire V V V V Insert the positive and negative wires into the V and V contacts on the terminal block connector Tighten the wire clamp screws for preventing the wires from loosing Wiring the Fault Alarm Contact The fault alarm contact is in the middle of terminal block connector as the picture shows below Inserting the wires it will detect the fault status including power failure port link failure and form an open circuit 7 Insert the wires into the fault alarm contact Note e Use Copper Conductors Only Tighten to 5 Ib in The wire gauge for the terminal block should be in the range between 12 24 AWG LED Indicators There are 7 diagnostic LEDs located on the Front panel of converter module They provide real time information of system and optional status The following table provides description of the LED status and their meanings for Industrial Ethernet to VDSL2 extender A a Power1 Green a Power 1 off Power 2 on Power2 Green Power 2 off Power1 Power2 is inactive Power1 and Power2 are both P Fail Red active o
2. or not 6 To remove the unit from the track reverse steps above Wall Mount Plate Mounting Follow the steps below to mount the unit with wall mount plate 1 2 3 4 Remove the DIN Rail from the unit loose the screws to remove the DIN Rail Place the wall mount plate on the top amp bottom side of the unit Use the screws to screw the wall mount plate on the unit Use the hook holes at the corners of the wall mount plate to hang the unit on the wall 5 To remove the wall mount plate reverse steps above Application 88 49Mbps up to 200 meters Up to 2Km for VDSL Twisted pair telephone line Ai y ra Mail and Web Server Troubles shooting Check the configuration DIP switch It must be setting in the same operation mode with the link partner m Select the proper Copper Phone line cable to construct your network Please check that you are using the right cable Appendix A Pin assignment e RJ 45 pin assignment The Fast Ethernet ports RJ 45 will auto sense for 10Base T or 100Base TX connections Auto MDI MDI X means that the switch can connect to another switch or workstation without changing straight through or crossover cabling Please refer to Table 1 for RJ 45 pin assignment Pin Number Assignment 1 TX 2 Tx 3 Rx 6 Rx Table 1 RJ 45 Pin Assignment Note and signs represent the polarity of the wires that make up each
3. Hardened Ethernet to VDSL2 Extender User Guide Revision History Rev 1 03 Dec 2009 Industrial Ethernet to VDSL2 Extender with Wide Operating Temp Document Date Revision Initials Release 1 00 Jun 04 2009 First release E C 1 01 Aug 13 2009 Add note for high temp environment E C 1 02 Oct 26 2009 Add Pin Assignment E C Modify Power Consumption and operating 1 03 Dec 01 2009 E C temperature for UL508 FCC Warning This Equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy It may cause harmful interference to radio communications if the equipment is not installed and used in accordance with the instructions However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to
4. Mbps 0 0 93 1 54 6 250 76 19 97 1 56 500 152 39 95 3 54 1 1000 304 79 81 44 1 1500 457 19 62 9 28 9 2000 609 59 45 8 18 3 2500 761 99 34 3 7 1 3000 914 39 25 8 7 9 3500 1066 79 21 8 5 3 4000 1219 19 16 4 6 2 4500 1371 59 18 5 0 8 5000 1523 99 18 4 0 8 5500 1676 39 14 8 0 7 6000 1828 79 11 7 0 6 6500 1981 19 9 5 0 5 Performance in AWG24 Fast mode SNR 6dB Symetric for ISDN Distance Feet Data Rate Feet m Downstream Mbps Upstream Mbps 0 0 80 5 88 5 250 76 19 83 8 90 6 500 152 39 81 4 86 8 1000 304 79 63 7 64 4 1500 457 19 47 9 40 0 2000 609 59 32 3 25 7 2500 761 99 23 2 14 3 3000 914 39 17 9 16 7 3500 1066 79 15 4 13 1 4000 1219 19 12 5 8 1 4500 1371 59 19 4 0 8 5000 1523 99 15 8 0 8 5500 1676 39 12 9 0 7 6000 1828 79 10 3 0 6 6500 1981 19 7 6 0 5 Mounting Installation DIN Rail Mounting The DIN Rail is screwed on the unit when out of factory If the DIN Rail is not screwed on the unit please see the pictures and follow the steps below to screw the DIN Rail on the unit Rear Side DIN Rail 1 Use the screws to screw the DIN Rail on the rear side of the unit 2 To remove the DIN Rail reverse the step 1 3 After the DIN Rail is screwed on the rear side of the unit insert the top of DIN Rail into the track 4 Then lightly push the DIN Rail into the track 5 Check if the DIN Rail is tightened on the track
5. n time and minimum expense by allowing video streaming and data to share the same telephone pair without interference Features IEEE 802 3 10BASE T Standard IEEE 802 3u 100BASE TX ITU T ITU T G 993 1 VDSL G 997 1 compatible Per unit Power1 Power2 P Fail LED Indicators LAN port LNK ACT SPD VDSL port LNK ACT CO 10 100TX 1 x RJ 45 with auto MDI MDI X function VDSL 1 x RJ 45 with female Phone Jack Connector DIP1 Master Slave switch DIP2 Impulse noise protection DIP3 Rate limit control DIP4 General protection 10Base T 2 pair UTP STP Cat 3 4 5 cable EIA TIA 568 100 ohm 100m Cabling 100Base TX 2 pair UTP STP Cat 5 cable EIA TIA 568 100 ohm 100m VDSL Twisted pair telephone Full VDSL2 bandwidth up to Down Stream Up Stream 200m gt 88 49Mbps 400m gt 63 29Mbps 600m gt 46 18Mbps 800m gt 30 5 7Mbps 1000m gt 22 5 3Mbps 1500m gt 18 0 8Mbps 2000m gt 9 0 5Mbps Power Consumption 24 VAC 50 60 Hz Maximum 7 7 W 12 48 VDC Maximum 6 W Class 2 Performance Based on AWG26 wires 40 C to 75 C Operating NOTE Temperature For use in Pollution Degree 2 Environment Maximum Surrounding Air Temperature 75 C Operating Humidity 5 to 95 non condensing Storage Temperature MBTF Safety Vibration EMC 40C 85 C 260895 hrs 36 6 x 140 x 95 mm IP 30 metal shell UL508 Class 1 Division 2 CE FCC Cla
6. r no power input LNK ACT for LAN OFF Link down Green Speed for LAN 10M tambon a COMA Acting as Customer Premise Equipment CPE side AE Acting as Central Office CO side CO Green gt LNK ACT for VDSL DIP switch The DIP switch is used to configure operation mode in below The default value of Dipswitch is OFF S W No Feature Status Description Acting as Customer Premise Equipment CPE Master Slave ON 1 side switch OFF Acting as Central Office CO side a Impulse noise ON Fast mode Direct data transmission with protection latency less than 1ms Interleave mode Provides communication OFF protection for up to 250ms impulse noise latency less than 6ms at Limit line rate Disable Provides up to Rate limit 100Mbps 60Mbps line rate in short line control opp Limitline rate Enable Line rate limited to 50 20 Mbps ON SNR 6dB Original and Normal channel noise 7 General protection with 6dB SNR protection ER SNR 9dB Higher SNR margin 9dB will result in less error with more stable VDSL link Note Please set DIP4 OFF when operating in harden environment That mean will keep better performance Data Rates and Distances Performance in AWG24 Line at 6db with full rate Performance in AWG24 Fast mode SNR 6dB 998 for ISDN Distance Data Rate Feet m Downstream Mbps Upstream
7. ss A EN61000 6 4 EN61000 6 2 EN61000 4 2 ESD EN61000 4 3 Radiated RFI EN61000 4 4 Burst EN61000 4 5 Surge EN61000 4 6 Induced RFI EN61000 4 8 Magnetic Field EN61000 4 11 Voltage Dip EN61000 3 2 Harmonics Current EN61000 3 3 Voltage Fluctuation amp Flickers IEC60068 2 27 IEC60068 2 32 IEC60068 2 6 Package Contents Beware of which type of extender that you have purchased And please refer to the package content list below to verify them against the checklist Industrial Ethernet to VDSL2 extender package contains following items gt VV V Y The Industrial Ethernet to VDSL2 extender User manual Block connector 2 wall mount plates and 6 screws One DIN Rail attached on the switch Compare the contents of your standalone extender with the standard checklist above If any item is damaged or missing please contact your local dealer for service Hardware Description The Industrial Ethernet to VDSL2 extender dimension 36 6 x 140 x 95 mm o o o o o O o o 140 00 o o o 0 0 olo 020 020 ore en Front Panel Industrial Ethernet to VDSL2 extender The Front Panel of the Industrial Ethernet to VDSL2 extender consists of one Ethernet port one VDSL Port and 3 LED Indicators Power1 Power2 P Fail SPD for LAN port LNK ACT for LAN port CO LNK ACT for VDSL P41 P2 P Fail aE S o v o cr mez ax CI b aes o e me mn
8. which the receiver is connected Consult the dealer or an experienced radio TV technician for help CE Mark Warning This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures Content IMMPOGUCE idad FEATURES is PACKAGE CONTENTS se cvessccesnavevenssaczosdsdusnceaueasaivaledeudceusaszcaissavadsa AAEE S EEEa KEER SASEA RIEAN ETES Hardware Description vstcces beset si tac ad bagi heated od dasa cen dete eens mc dade eeeadd sends dee net aptiiteidte FRONT PANEL cia as TOP TE A A AAA Penal Wea a oases WIRING THE POWER INPUTS ea a ia WIRING THE FAULT ALARM CONTACT A ci LED INDICATORS 0 td di MTS WC AA A ve re wee EEE Wedge DATA RATES AND DIS TANCES ii MOUATING INSTAN ANON este slcctct lene titetens O tds ID TNR Ae MOUNT e e ee Montane sean a WALL MOUNT PLATE MOUNTING esricioii ii APPLICATION A A Troubles O A arco Appendix A Pin AAN Anan an Aaah Introduce The Industrial Ethernet to VDSL2 extender is long reach Ethernet module with one Ethernet port RJ 45 connector and one VDSL port RJ 45 connector It provides Ethernet and VDSL technologies to extend Ethernet over single pair phone line by using a VDSL signal Up to 88 49 Mbps transition bandwidth within 200m and 22 5 3 Mbps for 1km long range connections provides ultra high performance to the pervasive telephone line network It has the advantage of minimum installatio
9. wire pair All ports on this industrial switch supports automatic MDI MDI X operation users can use straight through cables See figures below for all network connections to PCs or Servers or to other switches hubs In straight through cable pins 1 2 3 and 6 at one end of the cable are connected straight through to pins 1 2 3 and 6 at the other end of the cable Table 2 shows the 10BASE T 100BASE TX MDI and MDI X port pin outs Pin MDI X Signal MDI Signal Receive Data plus RD Transmit Data plus TD Receive Data minus RD Transmit Data minus TD Transmit Data plus TD Receive Data plus RD GW N Transmit Data minus TD Receive Data minus RD Table 2 MDI MDI X Port Pin outs The following figures show the cable schematic for straight through type Figure 1 and crossover type Figure 2 Switch Router PC 3 TD 3 RD 6 TD gt 6 RD 1 RD 1 TD 2 RD 2 TD Figure 1 Straight Through Cable Schematic Switch Switch 3 TD 3 RD 6 TD 6 RD 1 RD 1 TD 2 RD 2 TD Figure 2 Crossover Cable Schematic e PIN assignment for VDSL Port We support RJ 45 straight cable and RJ 11 2 wires straight cable too The data use 2 wires one pair as below picture shows Use one pair wires for data forwarding RJ 11 connector 1 RJ 11 connector 2

Manual

Contents

Download Pdf Manuals

Related Search

Related Contents