Earthworks PM40T Manual (PDF 3236 KB)
Contents
1. Earthworks Printed in U S A p M Earthworks USER S ANOJI MANUAL H PM4OT The Ultimate Piano Microphone System e _ That Will Change Piano Miking Forever k Assembled View Earthworks Custom Made in the U S A 12 Notes Congratulations on your purchase of the innovative Earthworks Touring PianoMic System We know that you will be thrilled with the results you will achieve using the Touring PianoMic System for both live performance and recording Items Enclosed with your New Earthworks Touring PianoMic System PianoMic System Model PM40 T 2 PianoMic telescoping bars with attached microphone heads 1 Microphone electronics box 1 Leather pouch for electronics box 2 Felt pads with adhesive backing 1 User s Manual for PianoMic System 1 Carrying case 1 Earthworks Full Line Catalog with Demo CD EVEN IF YOU DON T LIKE READING MANUALS PLEASE READ THIS SECTION BEFORE INSTALLING THE PIANOMIC SYSTEM USING THE PIANOMIC SYSTEM The majority of those who purchase the PianoMic System have experience in miking pianos with conventional microphones and may find the close miking techniques described in this Manual to be unconventional Please keep in mind that the PianoMic System utilizes a number of new technologies and that the PianoMic microphones work and perform much differently than conventional microphones The typical practices for piano mik2. System so that the sup port bracket does not rest on the curved part of the piano case deh PianoMic multi conductor shielded cable that connects to electronics box via 5 pin XLR Figure 8 Positioning the PianoMic Cable 5 Notice that one end of the PianoMic has a multi connector shielded cable coming out of the tube below the support arm Figure 8 It doesn t matter which side of the piano the cable exits The main objective is to place the PianoMic in the piano so that the microphone heads can be easily placed 2 to 3 inches in front of the dampers The cable is long enough to easily reach the opposite side of the piano should you decide to locate the electronics box on the opposite side of the piano from where the cable comes out of the PianoMic You will need to position the cable so it does not lie on top of the support arm The combined thickness of the support arm with the cable on top if it would exceed the size of the opening between the piano case and the lid Therefore when the lid is closed it would pinch and deform the cable To avoid this place the cable to one side of the support arm You may also position the cable so it comes out the open area of the piano as illustrated in Figure 8 6 Once you have determined which placement will provide you with the abil ity to have the microphone heads two to three inches in front of the dampers you are ready to place the PianoMic System inside the piano With the b
3. contact information on page 11 of this manual Earthworks the New Science in Microphones David Blackmer the brilliant engineer who in vented the technologies of dbx is also the inven tor and founder of Earthworks In the last few years of his life David developed a number of revolutionary technologies that dramatically improve the quality and performance of micro phones In short Earthworks High Definition Microphones will pick up sounds and details that other microphones cannot These dramatic improvements are in the areas of impulse re sponse diaphragm settling time and improved polar pattern technologies Those who have heard Earthworks High Definition Microphones say that they hear more attack more subtle detail and a more pristine quality in the sound than with any other microphones regardless of price Since David s death in 2002 the Earthworks engineers have continued to develop new inno vations in microphone design such as the PianoMic System FlexWand and High Definition Drum Microphones 4 Now take the two PianoMic telescoping sections and mate the connectors just like you would mate a standard XLR connector see Fig 1 D First mate the key ways and then push the connectors together until you hear a click If you do not hear a click then change the position of the rotating collar and try to mate the two sections again Figure 1 D Mate the two sections lt es by pushing until you
4. hear a click 5 Once you have heard the click when mating the two sections rotate the collar until it is firmly positioned against the mating connector cover finger tight At this point two sections should be firmly attached and will not be loose or wiggle Fig 1 E Figure 1 E Rotate collar all the way to the left firmly against the left connector body TO DISASSEMBLE 7 To dissamble the PianoMic rotate the collar between the XLR connectors the full distance from its mating half until it is snuggly against the right connector body as shown in Fig 1 F Figure 1 F 1 Rotate collar all the way m to the right connector body 1 8 Then grab the two mating connectors one with each hand and pull the two sec tions apart as shown in Fig 1 G Do not pull apart holding onto the telescoping tubes Figure 1 G Separate the two sections by holding onto each connector body ef 9 Collapse the telescoping bars and place them in the carrying case along with the electronics box and leather pouch Now you re ready to take your PianoMic to the next gig The PianoMic System provides the following benefits e Excellent overall piano sound with uniform level from all strings e Superb sound with the piano lid up or down e Tremendous gain before feedback e Minimal leakage from other instruments surrounding the piano with piano lid closed e Microphones are not visible from outside the piano People are astonished when t
5. piano Figure 4 Loosening the Clutches 3 Notice that on each end of the PianoMic bar there are support brackets that will be placed on the upper edge of the piano case sides These support brackets have rounded edges and are covered with a soft polyolefin coating to avoid scratching the piano The support brackets are thin enough to allow the piano lid to be completely closed with the Pi anoMic System inside the piano The PianoMic comes with felt pads installed on the top of each support arm If you desire a more snug fit with the lid closed or if vibration aie becomes an issue install one of the enclosed spare felt pads on the bot tom side of the support brackets as Figure 5 Support Arms and Installing Felt Pads shown in Figure 5 ppp N ALS LITMAN Ab KAKARA Figure 6 Facing the Mic Heads Towards the Dampers Figure 7 Facing the Mic Heads Away From the Dampers 4 The PianoMic can be placed inside the piano with the microphone heads either facing the dampers Figure 6 or facing away from the dampers Figure 7 For opti mum results the PianoMic System should be placed in the piano with the micro phone heads positioned two to three inches away from the dampers How you place the PianoMic System in the piano will depend upon the piano its size and how it is made This will govern whether the microphone heads can be faced toward or faced away from the dampers It is best to position the PianoMic
6. turns to the left WARRANTY All Earthworks products carry a two year limited warranty parts and labor If you have any problems with your Earthworks products please contact our warranty repair department by email at returns earthworksaudio com or by telephone at 603 654 6427 Ext 20 1K 5K 10K 180 20K PianoMic Polar Response PM40T Specifications Frequency Response 4Hz 40kHz Polar Pattern Omnidirectional random incidence Sensitivity 15mV Pa 36 dBV Pa Power requirements 48V Phantom 10mA Peak Acoustic Output 148 dB SPL Output XLR 3 pin 2 Min Output Load 600 ohms pins 2 amp 3 Noise 22dBA Mic Gooseneck Length 4 875 12cm Rod Length Assembled 64 160cm fully extended 46 115cm fully collapsed Rod Length Separated 23 58 4cm fully collapsed Carrying Case 24 5 x12 5 x4 619x317x100 cm Product Weight 6 Ibs 2 7 kg Shipping Dimensions 26 x18 x8 66x46x20 cm Shipping Weight 13 Ibs 6 kg Earthworks HIGH DEFINITION MICROPHONES Earthworks Inc 37 Wilton Rd Milford NH 03055 603 654 6427 ext 14 www earthworksaudio com Made in U S A 10 Now you should be ready to use the PianoMic System and achieve some impressive sonic results for recording or live performances If you have any questions after reading and following the directions in this manual please contact Earthworks directly using the
7. 1 December 15 2009 ASSEMBLING amp DISASSEMBLING THE TOURING PIANOMIC The PianoMic System is quick and easy to install Once you have initially set up the PianoMic System you will be able to do it from that point on in just a few minutes Here are some helpful guidelines CAUTION the microphone heads and goosenecks are permanently attached to the two PianoMic telescoping tubes and cannot be moved or removed Once assembled the distance between the two goosenecks is fixed at 16 inches one third of the width of a piano keyboard Check that all items are included with your Touring PianoMic System by using the list of Items Enclosed on page one of this manual TO ASSEMBLE 1 Remove the two PianoMic telescoping bars from the case Notice that on each of the two telescoping bars there is a special XLR type connector There is a rotating collar next to the special XLR type connector on the telescoping bar that has a cable coming out of one end see Section B in Fig 1 A Section A Section B Figure 1 A Sections A amp B of PianoMic 2 Rotate the collar on the XLR connector so it is snug against the connector cover but not too tight Fig 1 B Figure 1 B Rotate collar all the way to the right 3 Next rotate the collar two turns in the opposite direction moving it away from the connector cover toward the connector pins Fig 1 C Figure 1 C Rotate collar two
8. ar fully extended and the clutch adjusted where there is still a little friction place the support bracket on the edge of the piano case opposite you Then push on the bar until the PlanoMic is the correct length to allow the support bracket to easily rest on the edge of the piano case nearest to you f D AHUA P yy DPP 7 PDL 4 ih j J7 i Pi N ARORAA KANAANAN AAAA ARDADA Figure 9 Favoring the High Strings Figure 10 Favoring the Low Strings 7 With the PianoMic in place you will need to determine if you want the microphones to favor the high strings low strings or neither The center sec tion of the PianoMic can slide up to eight inches in either direction in order to favor the high or low strings if desired This positioning is illustrated in Figures 9 and 10 8 Once you have positioned the PianoMic center section tighten both clutches to insure that the PianoMic bar stays in place ee ae Figure 11 Adjustable flex arms for the Microphones 9 With the PianoMic in place you can move the flex arms attached to the mi crophone heads several inches to the left or to the right to achieve your desired placement See Figure 11 10 The flex arms also allow you to adjust the height of the microphone heads as shown in Figure 12 It is suggested that you place the microphone heads two to three inches above the piano strings
9. e electronics box in either of these two ways Any recording or live sound engineer will tell you that conventional microphones do a poor job inside a piano with the lid closed Sound engineers were amazed when they heard the exceptional sound quality of the PianoMic System used inside a piano with the lid open and at half stick But they were absolutely floored upon hear ing the fantastic performance with the lid closed When using a PianoMic System for live performance you will achieve the most gain before feedback with the piano lid fully closed You will also have the least amount of leakage from sounds outside the piano with the piano lid closed We know you will be more than pleased with the performance of the PianoMic System for both recording and live sound applications SETTING UP THE PIANOMIC 1 With the PianoMic assembled loosen the two clutches on either side of the two microphone goosenecks See Figure 4 When adjusting the clutches be sure to hold the larger diameter tube section with one hand While rotating the clutch with the NL other hand as indicated in figure 4 However do not loosen the clutches all the way just enough so the bar can be extended and still have a little fric tion This will make it easier to adjust the length of the bar from both ends 1 once it is placed inside the piano C2 gt gt TO ss gt as 5 2 Extend both sides of the bar so that it is wider than the
10. hey hear the exceptional sound quality of the PianoMic System with the piano lid closed Conventional microphones perform poorly in a piano as the sound inside the piano is coming from every direction and from multiple sound sources Every string is a sound source The soundboard is a large and complex sound source In addition sounds are re flected off the piano sides the soundboard and the piano lid multiple times with little attenuation Sounds inside a piano are randomly arriving from every pos sible direction at similar levels all at the same time This is a classic example of a diffuse sound field which is defined as a confined area where there are multiple sound sources and multiple reflections arriving at the microphone from every an gle at similar levels simultaneously A microphone that is placed in such a diffuse sound field has to pickup all of the sound with a proper tonal balance For optimum results this task requires a High Definition Random Incidence Microphone Conventional microphones are Free Field micro phones and regardless of their pickup pattern are designed to only pick up sounds accurately in front of the microphone See Figure 2 Random incidence micro a oe E phones are designed to Figure 2 Conventional Free Field Microphones inside a piano only pick up sound accurately in front of the microphone uniformly pick up sounds arriving simultaneously from all angles and direc tio
11. ing using conventional micro phones will most likely not apply when using the PianoMic System With the PianoMic System the rules for miking pianos have changed Conventional miking practices suggest that a piano must be miked from outside to achieve a good sound and that a good piano sound cannot be achieved with closely placed microphones inside the piano especially with the lid closed When you listen to the incredible results achieved using the PianoMic System at full stick half stick or lid closed you will realize how unique and groundbreaking it actually is As the PianoMic System changes many of the conventional rules and methods of miking pianos we strongly suggest that you start by following our guidelines first Afterwards if you want to experiment you can take it from there The Earthworks PianoMic System incorporates a number of proprietary technologies that allow this method of close miking pianos to achieve results that have previously not been possible This improved performance has been accomplished by using specially designed High Definition Microphones cre ated specifically to work inside a piano These are carefully matched Random Incidence omni microphones with extremely fast impulse response very short diaphragm settling time extended frequency response 4Hz to 40kHz near perfect polar response high current Class A amplifiers and the ability to handle sound pressure levels up to 148dB SPL Version
12. ns rather than to the Wa sound coming only from y a primary source that is in front of the microphone Random incidence micro phones have exceptional ac curacy and tonal balance in a diffuse sound field where sound arrives from all direc tions randomly and simulta neously See Figure 3 Figure 3 Random Incidence Microphones inside a piano pick up sound accurately from all directions Cable to PianoMic PianoMic electronics box in leather pouch Velcro strap To Leather Bag mixer preamp inputs 48V phantom required Figures 15 Placing the Electronics Box Figures 16 Attaching the Pouch in the Pouch to the Piano Leg Leather Pouch Attached to Piano Leg The enclosed leather pouch has Velcro straps that allow it to be attached to the leg of a piano The pouch is open at the top and the bottom has a strap to prevent the electronics box from falling out of the bottom There is an opening at the bottom of the pouch to conveniently attach the two standard XLR 3 microphone cables that go to your mixer preamp inputs See Figures 15 and 16 Figure 17 Mounting Electronics Box on a Microphone Stand Mic Lines to Preamp Input Cable to PianoMic Mic Stand Electronics Box Attached to Mic Stand Bracket The electronics box has a threaded insert in the bottom of the box that will mate with the threads on a standard microphone stand By this method the electronics box can be mounted to a short mic s
13. tand to keep it above floor level if desired see Figure 17 11 With the PianoMic placed in side the piano and the microphones properly positioned you are ready to connect the PianoMic cable to the electronics box via a 5 pin XLR con nector The back of the electronics box has two XLR 3 connectors that will connect the microphone outputs to the preamp inputs of your mixer Figure 13 Front and Rear of the See Figure 13 Electronics Box 12 Notice in Figure 14 that the top of each microphone head has a number These numbers correspond to the numbers on the rear of the electronics box Depending upon how the PianoMic is placed in the piano the high strings will be indicated by either the number 1 or num ber 2 Once the PianoMic has been placed identify the microphone numbers on the mic heads for both the high and low strings and remem Figure 14 Corresponding Numbers on Microphone Heads and Outputs of Electronics Box ber that they correspond to the numbers on the rear of the electronics box This will allow you to correctly identify the microphone sig nals for high and low strings that are connected to the preamps of your mixer Remember that the PianoMic requires 48 volt phantom power 13 There are two ways to mount the electronics box 1 in a leather pouch strapped to the leg of the piano or 2 attached to a short microphone stand The PianoMic System comes equipped to install th
Download Pdf Manuals
Related Search