Stainless Steel Gas Grill USER`S MANUAL
Contents
1. and preheat the grill for 15 minutes The grill lid is to be closed during the appliance preheat period Place the food on the grill and cook to the desired doneness Adjust heat setting if necessary The control knob may be set to any position between and 7 The grill is designed to grill efficiently without the use of lava rocks or briquettes of any kind Heat is radiated by the stainless steel flame tamers under the cooking grids 8 The hot grill sears the food sealing in the juices The longer the preheat the faster the meat browns 3 4 5 6 A USING THE SIDE BURNER 1 The side burner can be used to prepare side dishes such as beans potatoes corn or to warm sauces 2 Never close the side burner lid when the burner is lit 3 Use a 10 25cm diameter pot or smaller that does NOT have an extended handle when cooking on the side burner Center pot over burner 4 Use caution to avoid bumping grills side burner or pot to prevent pot from spilling contents possibly leading to severs burns 5 Do not use side burner to deep fry food in oil to avoid dangers associated with oil igniting creating a very dangerous situation 6 Remove the rotisserie kit when use side burner USING ROTISSERIE KIT 1 Take off the rotisserie kit from the grill 2 Slide off the left fork and load the meat or poultry onto the rod 3 Restore the left fork put two forks into the meat or p2. 777 772 1704 5701 ine 777 227 724 tl FOR OUTDOOR USE ONLY Stainless Steel Gas Grill USER S MANUAL MODEL NUMBER PG 50601SRL N This unit can match with both side shelves and side cabinets CUSTOMER SERVI CE 888 287 0735 Model Number PG 50601SRL N Stainless Steel BBQ Grill We warrant to the original consumer purchaser Purchaser of the Stainless Steel BBQ Grill Product that each Product shall be free from defects in workmanship and materials for a period of the years listed below from the date of original purchase Our obligation under this warranty shall be limited to repair or replacement of or adequate compensation for the Product at the option of us during the warranty period Our liability shall not extend beyond repair or replacement or the cost equivalent thereto This warranty does not cover Product that have been altered or damaged due to normal wear rust abuse improper maintenance improper use disassembly of parts and or attempted repair by anyone other than an authorized employee of Permasteel Inc This warranty does not cover surface scratches rust or heat damage to the finish which is considered normal wear The warranty period of the years listed below shall not be extended or renewed by the repair or replacement of or compensation for the Product If your Product is defective or o
3. THE REGULATOR SHALL NOT BE IN A LOCATION THAT WILL ATTAIN A TEMPERATURE ABOVE 140 F 60 C THE REGULATOR SHALL INCORPORATE A PRESSURE RELIEF VALVE OR OVERPRESSURE DEVICE THE INLET OF THE PRESSURE REGULATOR SHALL BE FITTED TO CONNECT THE TYPE 1 CONNECTION OF THE TANK VALVE PER ANSIZ21 81 1 Make sure tank valve is in its full OFF position turn clockwise to stop 2 Check tank valve to assure it has proper external male threads type connection per ANSIZ21 81 3 Make sure all burner knobs are in their OFF position 4 Remove the protective cap from LP tank valve Always use cap and strap supplied with valve 5 Inspect valve connection port and regulator assembly Look for any damage or debris Remove any debris Inspect hose for damage Never attempt to use damaged or plugged equipment Contact your local LP gas dealer for repair 6 When connecting regulator assembly to the valve hand tighten nut clockwise to a positive stop Do not use a wrench to tighten Use of a wrench may damage quick coupling nut and result in a hazardous condition 7 Open tank valve fully counterclockwise Use a soapy water solution to check all connections for leaks before attempting to light grill a leak is found turn tank valve off and do not use grill until a local L P gas dealer can make repairs DISCONNECT THE TANK WHEN THIS GRILL IS NOT IN USE 1 Turn all the knobs off 2 Turn the tank valve off fully turn clockwise to stop 3
4. center for help 888 287 0735 7 Always close the tank valve after leak testing by turning clockwise Only those parts recommended by the manufacturer should be used on the grill Substitution will void the warranty Do not use the grill until all connections have been checked and do not leak SAFETY TIPS 1 Always check for leaks after every gas tank change 2 Always check for leaks before each use 3 Check all gas supply fittings for leaks before each use It is handy to keep a spray bottle of soapy water near the shut off valve of the gas supply line Spray all the fittings Bubbles indicate leaks 4 Disconnected gas cylinders must have threaded valve plugs tightly installed and must not be stored in a building garage or any other enclosed areas 5 Turn off all control knobs and gas tank valve when the grill is not in use 6 If the appliance is stored indoors the gas tank must be disconnected and removed from the grill 7 Gas tanks must store outdoors in a well ventilated area Disconnected gas tanks in storage or being transported must have a safety cap 8 Never leave a gas tank in a recreational vehicle or boat which may become overheated by the sun 9 Do not store gas tank in or near an area where children play TO TEST GAS LEAK ON NATURAL GAS GRILL 1 Make sure all control knobs are in the OFF position 2 Turn on the natural gas supply If you hear a rushing sound turn gas off immediately There is a m
5. Detach the regulator assembly from tank valve by turning the quick coupling nut counterclockwise 4 Install the protective cap back onto the LP tank valve WARNING Neverinsert any foreign objects into the valve outlet It may damage the valve and cause leak leaking gas may result in fire explosion heavy body injury or even death Donotuse this grill until leak tested fyou cannot stop gas leak close the LP tank valve IMMEDIATELY call LP gas supplier or the fire department DANGER NEVER store a spare LP tank under or near grill or in an enclosed area NEVER fill the tank beyond 80 full An overfilled spare LP tank is dangerous because surplus gas may leak from safety relief valve The safety relief valve on a LP tank could activate to release gas and cause a fire The spare LP tank must have safety caps installed on the LP tank outlet If any gas leaks are found on the spare LP tank immediately step away from the grill and call the fire department CONNECTION FOR NATURAL GAS NG GRILLS Model PG 50601SRN Your natural gas grill is factory built to operate using natural gas only Never attempt to operate your grill on gases other than the type specified on the grill rating plates Your grill operates at 7 inch water column pressure Verify supply pressure with your local gas company If supply pressure is different than 7 inch contact a certified plumber for assistance Not for use with LP
6. Own Rent Comments Suggestions PERMASTEEL PERIVASTEEL INC 14231 FERN AVENUE BUILDING 10 CHINO CA 91710 TEL 888 287 0735 909 287 0733 EMAIL SERMCEGPERMASTEEL NET
7. damage Some parts of this grill may have sharp edges Please wear suitable protective gloves IMPORTANT This grill is intended for outdoor use only and is not intended to be installed in or on recreational vehicles or boats NOTE TO INSTALLER Leave this User s Manual with the customer after delivery and or installation NOTE TO CONSUMER Leave this User s Manual in a convenient place for future reference The symbols listed here are being used through out this User s Manual Please pay special attention to them The meaning of each of the symbols is listed here DANGER this symbol indicates an imminently hazardous situation which will result in death or serious bodily injury if not properly followed WARNING this symbol indicates a warning of potential serious bodily injury if the instructions are not strictly followed Please be sure to read and follow all these messages carefully CAUTION this symbol indicates potentially hazardous situation which may result in minor or moderate bodily injury if the instructions are not properly followed WARNING READ THIS SECTION FIRST BEFORE INSTALLING THE GRILL Your grill has been designed to operate using only the gas specified on the rating plate Do not attempt to operate your grill with other gases Failure to follow this warning may result a fire hazard and bodily harm and PermaSteel will void your warranty installati
8. gas BEFORE CONNECTION The natural gas hose and assemble are not supplied with this grill Please purchase a CSA approved Hose and assemble in local reputable dealer Hose and assembly are CSA listed for natural gas manufacturer gas mixed gas and for liquefied petroleum and for LP Gas Air mixtures on basis of 0 64 specific gravity for 1000 BTU s per cubic foot of gas at 0 3 inch water column pressure drop Only ANSI Z21 54 approved hoses should be used with this grill The appliance and its individual shut off valve must be disconnected from the gas supply piping system during any pressure testing on that system at test pressures in excess of 1 2 psi 3 5Kpa 20 The appliance must be isolated from the gas supply piping system by closing its individual manual shut off valve during any pressure testing of the gas supply piping system at test pressure equal to or less than 1 2 psi 3 5Kpa A WARNING Do not use hard metal piping of any kind to connect this type of grill to natural gas source Use only hose specified by reputable dealer Using hard metal piping or convoluted metal tubing is an unsafe practice Movement of the grill can cause breakage of metal pipe DANGER Connection should be made by a certified plumber Supply the plumber with a copy of these instructions Incorrect connection can result in a gas leak with possibility of fire CONNECT YOUR GRILL TO NATURAL GAS SOURCE 1 Insert the inle
9. 9 Cooking Grids Back Panel Back Bracket Hose Bushing 1 Searing Burner Bracket Right Upper Door Hinge Bracket 76 Pipe 17 Heat Shield Searing Burner Left Upper Door Hinge Bracket 18 Burners 5 Sliding Bars 4 2 Firebox 2 Ignition Electrode Rear Burner Rear Panel 66 HandleSeats 18 Rear Bumer Rear Burner Cover 68 Casters WihoutBrake Left Lower Door Hinge Bracket Ferm ocouple Cave de She Suppor BT Side Burner Lid 1 Right Door 1 38 Sie E S Rear Burner Vae hermocouple 92 PO DO N o NiO oe 1 wow ww OPTIONAL SIDES FOR CHOICE Dear Customer Below parts are optional for your choice no included with grill A Side Shelves oS a B Side Cabinets REF Parts of Left Shelf Left Side Shelf Support Motor Bracket Push Bar Parts of Right Cabinet 775 let Side Panel 8 Siding Bars 9 ASSEMBLE THE SIDE SHELVES TO GRILL Tools Re
10. ajor leak at the connection Correct before proceeding 3 Create a mixture of half water and half liquid dishwashing soap Brush soapy solution onto the following A Quick disconnect coupler B The full length of gas supply hose C Gas supply connection to gas manifold KO Ooo OO 00000 WARNING PRE START CHECKLIST Property damage bodily harm severe burns and death could result from failure to follow these safety steps These steps should be performed after the grill has been assembled stored moved cleaned or repaired DO NOT operate this grill until you have read and understand ALL of the warning and instructions in this manual Ensure that the grill is properly assembled The LP regulator amp hose connected to grill are provided by the manufacturer Inspect the natural gas supply hose for burns chaffing kinks and proper routing before each use If it is evident there is excessive abrasion or wear or the hose is cut it must be replaced prior the grill being used Leak check all gas connections and hose All internal packaging removed Burners are sitting properly on orifices Knobs turn freely Properly place the empty grease tray onto grease tray brackets to catch grease during use User informed of gas supply shut off valve location Position your grill on lever ground in a well ventilated location at least 36 clearance maintained from combustible materials buildings and overhangs Ens
11. connected to the grill 3 Store the grill in dry indoors ONLY after the tank is turned off and removed or disconnect from the natural gas source The tank must be stored outdoors out of the reach of children NEVER store the tank in a building garage or any other enclosed area 4 Put on the supplied vinyl cover ue 32 Thank you for purchasing the PermaSteel Grill In order to register your product to receive streamlined customer service please fill out the following Product Registration form and 1 fax the form and a copy of your receipt to FAX 909 287 0733 or 2 mail the form and a copy of your receipt to PermaSteel Inc 14231 Fern Avenue Building 10 Chino CA 91710 PRODUCT REGISTRATION First Name Last Name Address RS City State Zip Code Email Address Phone Product Model Date of Purchase Retail Store Location of Purchase Please rate the importance of each feature 1 least important 10 most important Quality Price Size Capacity Cooking Area Appearance Other What other brands did you seriously consider before making this purchase DCS CharBroil_ Brinkman_ Members Mark Lynx Other Did not consider other brands _ How did you hear about our product Magazine Ad Catalog Salesperson Word of Mouth Internet Store Display Other Marital Status Single _ Married Household Income Below 50 000 50 000 150 000 150 000 _ Education High School College Graduate School Primary Residence
12. d detergent or nonabrasive cleaner and warm soapy water Wipe dry with a soft nonabrasive cloth Granite surfaces If the appliance is equipped with a granite countertop to protect granite countertops against stains and discoloration use a high quality penetrating sealant made specifically for granite The sealant should be applied periodically throughout the year For standard maintenance on granite countertops wipe with warm water or mild soapy water Cleaners made specifically for cleaning granite may be used as necessary Do not use vinegar cleaners that contain acid abrasive cleaners or furniture polish We suggest the following routine care Clean up spills immediately Dust with an untreated cloth Use coasters Keep planters off the surface Always keep covered when not in use BEFORE CALLING FOR SERVICE Please check the following problems solutions before contact our service center 888 287 0735 PROBLEMS POSSIBLE CAUSE SOLUTIONS Electrode deposited with Use clean swab and alcohol to clean cooking residues Bumer want light after turning and Electrode wires are loose Reconnect or replace with new electrode Nogas Open the LP tank valve Replace LP tank valve Burner can t light by Clear burner tubes match Incorrect assembly Call our customer service center at flame with gas odor 888 287 0735 Low heat with knot in HI position Flare up _ e Flame lifting Too high o
13. del PG 50601SRL Your LP gas grill is factory built to operate using liquid propane gas only Never attempt to operate your grill on gases other than the type specified on the grill rating plates Your regulator supplied with your liquid propane gas grill is set for 11inch water column pressure and is for use with propane gas only The regulator and factory supplied hose assembly must be used when operating your grill with 20165 LP gas cylinder If replacement of the hose and or regulator becomes necessary factory specified parts are required LP TANK USED WITH YOUR GRILL MUST MEET THE FOLLOWING 1 Measurement 12 30 5cm Diameter X 18 45 7cm Tall 2 Maximum Capacity 20lbs 9Kg 3 Constructed and marked in accordance with the specification for LP gas cylinders of the U S Department of Transportation DOT or the National Standard of Canada CAN CSA B339 Cylinders Spheres and Tubes for the Transportation of Dangerous Goods 4 Is arranged for vapor withdrawal 5 Includes a collar to protect the tank valve 6 Provides a shut ff valve terminating in an LP gas tank valve outlet LP TANK VALVE USED MUST MEET THE FOLLOWING 1 Have type connection complying with the latest edition of ANSI 721 58 2 Have safety relief valve 3 UL listed Overfill Protection Device OPD This OPD safety feature is identified by a unique triangular hand wheel 18 CONNECT THE REGULATOR TO THE LP TANK VERY IMPORTANT
14. e burner can be match lit Tools Lighting rod hanging behind the right door 26 Usage 1 Read instructions before lighting 2 Open the lid during lighting 3 Simply place a lighted match between the coils on the end of the lighting rod and hold next to the burner to ignite 4 Push and turn the knob to position make sure the burner lights and stays lighted 5 Repeat 3 4 to light other burners 6 Keep a spray bottle of soapy water near the gas supply valve and check the connections before each use Do not light the grill if odor of gas is present call out service center FLAME CHARACTERISTICS 1 Check for proper burner flame characteristics Each burner is adjusted prior to shipment however variations in the local gas supply may take subtle necessary adjustments 2 Burner flames should be blue and stable with small yellow tips no excessive noise or lifting If any of these conditions exist call our customer service line If the flame is yellow it indicates insufficient air If the flame is noisy and tends to lift away from the burner it indicates too much air 3 Small yellow tips ok TO LIGHT THE REAR BURNER OF THE GRILL 1 Read instructions before lighting 2 all knobs to OFF then open the tank valve Always keep your face and body as far from the grill as possible when lighting 3 Open lid during lighting 4 Push down the safety valve switch button and
15. eparately rotisserie kit is available please follow below assemble steps Take out rotisserie parts from carton Tread key washers and counter balance onto treaded end of rotisserie rod next tread handle and tighten slide shaft collar through other side of rod followed by the two prongs forks should be pointing towards each other tighten thumb screws on shaft collar and prongs Take out motor from the carton And place it in the bracket STEP VI When the grill island is in the desired location lock the caster brakes of cabinets this will keep them in place for safe operation Safety Notice The regulator hose natural gas hose should go through the U shaped bracket in order to prevent the hose from lifting up and touching the hot firebox Note if replacing regulator natural gas hose please make sure to put regulator hose natural gas hose through U shape bracket WARNING IMPORTANT PG 50601SRL has been designed to operate using only LP gas PG 50601SRN has been designed to operate using only Natural Gas please notice the gas specified on the rating plate Do not attempt to operate your grill with other gases Failure to follow this warning may result in a fire hazard and bodily harm CONNECTION FOR LIQUID PROPANE GAS LPG GRILLS Mo
16. f a gas pressure Call the gas dealer Flashback Burner port blocked Clean burner port Grease accumulated in Turn off knobs and LP tank valve Leave lid open food and let fire burn out Clean the grill after cooling FOOD SAFETY 1 Always follow the following tips to enjoy safe and healthy outdoor grilling 2 Always use hot soapy water to wash hands surfaces amp utensils after processing raw meat 3 Always separate raw meat from cooked foods to avoid cross contamination 4 Always use clean utensils to handle the food 5 Always cook the meat thoroughly to kill germs Use a thermometer to inspect the inner temp of the meat if necessary 6 Place the cooked foods and leftovers promptly into the refrigerator when done eating VERY IMPORTANT DO NOT LEAVE THE GRILL UNATTENDED WHILE COOKING SPIDER AND INSECT WARNING Spiders and insects can nest in the burners after storing These nests can cause fires inside the tube or beneath the grill This is a very dangerous condition So always clean the burners before use WHEN TO LOOK FOR SPIDERS Inspect the burners at least once a year or immediately if any of the following conditions occur 1 Yellow flame with burning smell 2 Temperature wont rise 3 Heats unevenly 4 Burners make popping noises GRILL STORAGE 1 Clean the grill 2 Store the grill in a well ventilated dry outdoor area Keep out of the reach of children when tank is
17. hold on with right hand allowing the gas to reach the burner 5 Push and turn rear burner knob slowly to HI position with left hand 2 seconds later than push down the button The built in igniter will click and spark simultaneously to light the burner once burner lights Keep pressing safety valve button for 15 seconds to allow the safety valve to open Turn the control knob to OFF and release the button IMMEDIATELY if the burner does not light within 5 seconds Wait 5 minutes for gas to dispel then repeat the lighting procedure 6 Follow match lighting instruction if burner can t be lit after repeating 3 4 times TO LIGHT THE REAR BURNER BY MATCH 1 Read instructions before lighting 2 Open the lid during lighting 3 Push and turn the rear burner knobs slowly to position then release 4 Push down the safety valve switch button with right hand and hold on light by match with left hand Make sure the burner lights and stays lighted TO LIGHT THE SEARING BURNER OF THE GRILL 1 Read instructions before lighting 2 Turn all knobs to OFF then open the tank valve Always keep your face and body as far from the grill as possible when lighting 3 Open lid during lighting 4 Push and turn searing burner knob slowly to position with left hand 2 seconds later The built in igniter will click and spark simultaneously to light the burner once burner lights Turn the control
18. knob to OFF and release the button IMMEDIATELY if the burner does not light within 5 seconds Wait 5 minutes for gas to dispel then repeat the lighting procedure 5 Follow match lighting instruction if burner can t be lit after repeating 3 4 times TO LIGHT THE SEARING BURNER BY MATCH 1 Read instructions before lighting 2 Open the lid during lighting 3 Push and turn the searing burner knobs slowly to HI position then release 4 Light by match Make sure the burner lights and stays lighted TOTAL GAS CONSUMPTION Total gas consumption per hour of PG 50601SRL N grill with all burners Main burners 60 000 Btu hr Searing burner 16 000 Btu hr Rear burner 14 000 Btu hr Side burner 12 000 Btu hr Total 102 000 Btu hr 28 USING THE GRILL Grilling requires high heat for searing and proper browning Most foods are cooked at the heat setting for the entire cooking time However when grilling large pieces of meat or poultry it may be necessary to turn the heat to a lower setting after the initial browning This cooks the food through without burning the outside Foods cooked for a long time or basted with a sugary marinade may need a lower heat setting near the end of the cooking time 1 Make sure the grill has been leak tested and is properly located 2 Remove any packing material Light the grill burners using the instructions in this manual Turn the control knob to
19. mediately check if the smell of gas is detected BEFORE TESTING 1 Make sure that all packing material is removed from the grill including the burner tie down straps 2 Do not smoke while leak testing 3 Never leak test with an open flame 4 Make a soap solution with one part liquid detergent and another part water Prepare a spray bottle brush or rag to apply the solution to the connections For the initial leak test make sure the cylinder is full 5 Grill must be leak tested outdoors in a well ventilated area away from ignition sources such as gas fired or electrical appliances and flammable materials 6 Keep grill away from open flames and or sparks while testing TO TEST GAS LEAK ON LP GAS GRILLS 1 Make sure all control knobs are in the OFF position 2 Make sure the regulator is connected to the tank tightly 3 Completely open tank valve by turning counter clockwise If you hear a POP sound turn gas off IMMEDIATELY as it indicates a heavy leak at the connection Call your gas dealer or fire department 4 Check every connection from the tank up to and including the connection to the manifold pipe assembly the pipe that goes to the burner by brushing or spraying the soapy solution on the connections 5 If soap bubbles appear there is a leak Turn off tank valve IMMEDIATELY and retighten connections open tank valve again and recheck 6 If leaks cannot be stopped DO NOT ATTEMPT TO REPAIR Call our service
20. ng materials 7727 7 747 777 bil 7 77 777 477 477 77 000 744 7 74 ASSEMBLY INSTRUCTIONS STEP Il Place the motor bracket to the left side cabinet with 2 pcs of 1 4 20 1 2 screws STEP Ill Remove packing material from flame tamers cooking grids warming rack then place them in the proper positions shown below NW Aw 3 wr WS V WER we Wo amp N SA When the grill is in the desired location lock the caster brakes this will keep the grill unit in place for safe operation NN V Nen Wi NN Y We Wi WN A STEP V Place the side cabinets close to grill make them on the same line 7 Wt tl MC M dH oiy IT T 9 If UNA V lt y gt 1 MM as L4 VY i K 5 u M MM 1 t Af M re M t 4 Y AU gt TA jl m AN if iW If s
21. on of this appliance must conform with local codes or in the absence of local codes with either the National Fuel Gas Code ANSI Z223 1 NFPA 54 CAN CGA B149 1 Natural Gas and Propane All electric accessories such as rotisserie must be electrically grounded in accordance with local codes or National Electrical Code ANSI NFPA 70 or Canadian Electrical Code CSA C22 1 Keep any electrical cords and or fuel supply hoses away from any hot surfaces his grill is safety certified for use in the United States and Canada only Never modify to use in other places Modification may cause serious bodily injury or property damage PermaSteel is not responsible for any modifications and all warranties will be void AX WARNING FOR YOUR SAFETY PLEASE READ THIS SECTION FIRST f you smell gas Shut off gas to the grill Extinguish any open flames immediately Open the grill lid f the odor persists please call your gas supplier or your fire department immediately Do not store or use gasoline or other flammable items in the vicinity of this grill Any LP cylinder that is not connected for use should not be stored in the vicinity of this grill DESCRIPTION QTY DESCRIPTION lip Rings Side Burner Valve ame Plate Safty Switch amp Bottom id Handle Seat id Handle 1 Corrugated Pipe A Temp Gauge Control Panel 6__ Gauge Sea 3 ekes 7 Doubie yer Lia Warming Rack
22. oultry as far as possible Make sure the meat or poultry is located in the middle of the rod Screw the wing nuts of the fork as tight as possible 4 Wrap the food with butchers string never use nylon or plastic string to secure any loose portions if necessary 5 Restore the rotisserie kit into the motor 29 MAINTENANCE 1 Keep the grill area clear and free from combustible materials gasoline and other flammable vapors and liquids 2 Keep the holes in the three sides of the cart clear and free from debris thus ensure the flow of combustion and ventilation air is unobstructed 3 Visually check burner flames as following Remove cooking grids and flame tamers Light burners Turn knobs from HI to LO check the flame status the flame in LO position should be smaller than in HI position as figure shown below Always check flame before each use see TROUBLESHOOTING if any abnormal status found 4 4 Y CLEANING Stainless steel surfaces To maintain your grill s high quality appearance wash with mild detergent and warm soapy water and wipe dry with a soft cloth after each use Baked on grease deposits may require the use of an abrasive plastic cleaning pad Porcelain surfaces Because of glass like composition most residue can be wiped away with baking soda water solution or specially formulated cleaner Use nonabrasive scouring powder for stubborn stains Painted surfaces Wash with mil
23. quired 2 Philips head screwdriver not provided Hexagon Allen wrench provided The following hardware kit is provided with granite side shelves Description Quantity Truss head screw 1 1 4 20 1 2 With Split lock And Gasket Truss head screw i With Split lock And Gasket iij 5 32 32x3 8 BBQ hooks STEP I out main body of grill from carton Remove all the packing materials STEP Il Take out left side shelf from carton Use two 1 4 20x1 2 screws to attach left side shelf from inside of the firebox and use three same screws to attach it from outside of firebox Use three 5 32 32x1 2 screws to attach left side shelf angle iron to side shelf and also use two same screws to attach it to firebox from outside Use four 1 4 20x1 2 screws to attach push bar to left side shelf Use two 1 4 20x1 2 screws to install motor bracket on left side shelf Take out four S style BBQ tool hooks from the hardware bag then hang on the edge of the left side shelf STEP IV out right side shelf from carton Use two 1 4 20x1 2 screws to attach right side shelf from inside of the firebox and use three same screws to attach it from outside of firebox Use three 5 32 32x1 2 screws to attach right side shelf angle iron to side shelf and also use two same screws to attach it to fi
24. rebox from outside Use four 1 4 20x1 2 screws to attach push bar to right side shelf 38 webu NU WH AW WA N NON NX Remove packing material from flame tamers cooking grids and warming rack then place them in the proper positions shown below NW Wi Wi If separately rotisserie kit is available please follow below assemble steps Take out rotisserie parts from carton Tread key washers and counter balance onto treaded end of rotisserie rod next tread handle and tighten slide shaft collar through other side of rod followed by the two prongs forks should be pointing towards each other tighten thumb screws on shaft collar and prongs Take out motor from the carton and place it in the bracket STEP VI When the grill is in the desired location lock the caster brakes this will keep the grill unit in place for safe operation ASSEMBLE SIDE CABINETS GRILL Tools Required 2 Philips head screwdriver not provided Hexagon Allen wrench provided following hardware is provided with island sides Description Specification Quantity Truss head screw Y With Split lock And Gasket STEP I out grill body and the cabinets from packing carton and remove all the packi
25. t connection to grill cabinet from back of grill Tighten it to gas manifold with wrench Make sure to put natural gas hose through U shape bracket Gas manifold Quick disconnect coupler 21 2 Coat pipe nipple with gas resistant teflon tape or pipe dope Tighten quick disconnect coupler onto pipe nipple that leads to natural gas supply Insert cover when hose is disconnected Quick disconnect coupler Plug Hose Supply valve Sleeve 3 After grill is completely assembled make sure natural gas supply valve is OFF and then connect natural gas hose to socket Push sleeve back on socket and insert plug until sleeve snaps forward locking plug into socket Be sure to leak test these connections prior to use Push sleeve back to attach Supply valve Socket Sleeve Notice Please also follow the instructions which attached on the natural gas hose assemble you purchase for connection steps DISCONNECT YOUR GRILL FROM THE NATURAL GAS SOURCE 1 Turn natural gas supply valve to OFF position 2 Push sleeve back and pull plug out of sleave Although all gas connections on the grill are leak tested at the factory prior to shipment a complete gas tightness check must be performed at the installation site due to possible mishandling in shipment or excessive pressure unknowingly being applied to the unit Periodically check the whole system for leaks or im
26. therwise requires service or parts please first call PermaSteel Customer Service toll free at 888 287 0735 between 8 00 a m and 5 00 p m PST Please tell us which model you purchased the date of purchase and the problem with your Product We will use our very best efforts to honor this warranty and repair replace or compensate you for your Product through your original place of purchase A copy of your original purchase receipt must accompany your service request Component Warranty Period Burners 3 Years Flame Tamers amp Cooking Grids 2 Years Valves 1 Year Frame Housing Cart Control Panel Igniter and Related Parts 1 Year Stainless Steel Parts 1 Year Granite countertop 1 Year LIMITATION OF REMEDIES AND LIABILITY We shall not be liable for any incidental or consequential damages for breach of any express or implied warranty on its Product Except to the extent prohibited by applicable law any implied warranty or merchantability or fitness for a particular purpose on this Product shall be limited to the duration of the above warranty Neither us nor anyone else who has been involved in the creation production or delivery of the Product shall be liable for damages of any type including but not limited to any lost profits lost savings loss of anticipated benefits or other incidental or consequential damages which may arise out of the purchase use or inability to use the Product whether arising out of con
27. tract negligence strict tort or under any warranty or otherwise even if you have been advised of the possibility of such damage or any other claim by any other party Our liability for any breach of warranty shall be limited to repair or replacement of the defective part or parts as described above Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you The above warranty gives you specific legal rights and you may have other rights which vary from state to state BEFORE YOU BEGIN MESSAGE TO OUR USERS SAFETY SYMBOLS INSTALLATION amp SAFETY PRECAUTIONS GAS WARNING ASSEMBLY POST ASSEMBLY GAS CONNECTION LEAK TESTING FINAL INSTALLATION CHECK LIST GRILL LIGHTING INSTRUCTION OPERATING INSTRUCTION CARE amp MAINTENANCE TROUBLE SHOOTING FOOD SAFETY GRILL STORAGE PAGE 3 PAGE 5 PAGE 8 PAGE 13 PAGE 18 PAGE 23 PAGE 25 PAGE 26 PAGE 28 PAGE 30 PAGE 31 PAGE 32 PAGE 32 Thank you for your purchase of our Stainless Steel BBQ Gas Grill We sincerely wish you will enjoy using our fine products Please read this User s Manual its entirety before using the grill Please contact our customer service at 888 287 0735 if you have any questions Please read this User s Manual carefully Failure to follow the provided instruction can result in seriously bodily injury and or property
28. ure that all electrical supply cords are properly grounded Keep any electrical supply cord and the fuel supply hose away from any heated surfaces Hose should be at least 3 inches from hot surfaces There is no unprotected combustible construction material over the grill Do not obstruct the flow of combustion and ventilation air VERY IMPORTANT ALWAYS INSPECT THE HOSE PRIOR TO EACH USE BEFORE LIGHTING Inspect the gas supply hose before turning the gas If there is evidence of cuts wear or abrasion it must be replaced before use The replacement hose assembly must be that specified by the manufacturer VERY IMPORTANT TO LIGHT MAIN AND SIDE BURNERS THE GRILL 1 Read instructions before lighting 2 Turn all knobs to OFF then open the tank valve Always keep your face and body as far from the grill as possible when lighting 3 Open lid during lighting 4 Push and turn any control knob slowly to HI position The built in igniter will click and spark simultaneously to light the pilot and burner in sequence Turn the control knob to OFF IMMEDIATELY if the burner does not light within 5 seconds Wait 5 minutes for gas to dispel then repeat the lighting procedure 5 Follow match lighting instructions if burner can t be lit after repeating 3 4 times TO LIGHT MAIN AND SIDE BURNERS BY MATCH AS THE FOLLOWING FIGURE SHOWS If the burner will not light after several attempts then th
Download Pdf Manuals
Related Search