Click on the
Contents
1. 11 Channel List 12 Technical Parameters 12 xImportant notice e In this instruction for use contains about the installment and the use aspect important information of the beam moving head When installing and using you need to look this usage instruction strictly Before open the beam moving head and if you want to do the repair work please make sure the power source is at the separation condition e Every unit is tested completely and packed properly by the manufacturer Please make sure the packing and the unit are in good condition before installation and use Should there be any damage caused by transportation consult your dealer and do not use the unit Any damage caused by improper use will not be assumed by the manufacturer or dealer Attention Unceasingly carries on the product improvement about our company the policy in this instruction booklet carries the data will have the possibility to be able to change in the future when no longer separate notice change matters concerned Our company retains when the product improvement changes the related specification the authority This instruction booklet publisher cannot be responsible regarding this instruction booklet in information accurac2. 4 fast fit screws and remove the back cover when fitting replacing the lamp Do not touch the bulb of the new lamp with bare hand so as not to influence the beam output Do not harm the sticking out point of the lamp during its installation Fit new lamp and close the back cover by fastening 4 fast fit screws when finished lamp installation Lamp work will reach a very high temperature Vapor discharge lamp can not continue to supply this physical characteristics therefore the power completely cool for 10 minutes before on the operation Failure to do so will lead to a high pressure discharge and short circuit burned out the computer s control panel components Notes Unplug the light from power before lamp installation or replacement and wait for it to cool www mjledlighting com sepa Lois Beamspot 230 MJ 1020 User Manual ver1 0 Power Code Connection Connect the power cord as follows L live brown E earth yellow green N neutral blue Use the plug provided to connect the mains power to the projector paying attention to the voltage and frequency marked on the panel of the projector It is recommended that each projector be supplied separately so that they may be individually switched on and off A It is essential that each projector is correctly earthed and the electrical installation conforms to all relevant standards DMX Connection DMX OUT DMX IN DMX 512 E3 DMX OUT DMX IN 5 PIN g 5 949 2
3. Channel Mode and choose Channel Mode by UP amp DOWN it will be show 16 or 20 to confirm by press Ok button Press Invert Pan Mode and choose Invert Pan by UP amp DOWN it will be show ON OFF to confirm by press Ok button Press Invert Tilt Mode and choose Invert Tilt by UP amp DOWN it will be show ON OFF to confirm by press Ok button Press Swap Pan Tilt Mode and choose Swap Pan Tilt by UP DOWN it will be show ON OFF to confirm by press Ok button N ad n A www mjledlighting com NO ly A Beamspot 230 MJ 1020 User Manual ver1 0 7 Press Encoder Pan Tilt and choose Encoder Pan Tilt by UP DOWN it will be show ON OFF to confirm by press Ok button 8 Press No DMX Signal Mode and choose No DMX Signal by UP DOWN it will be show KEEP CLEAP to confirm by press Ok button 9 Display Power Save is screen saver Press Display Power Save and choose Display Power Save by UP amp DOWN it will be show ON OFF to confirm by press Ok button 10 Turn On Startup Mode is turn on the lamp when the turn on the power Press Turn On Startup Mode and choose Turn On Startup by UP DOWN it will be show ON OFF to confirm by press Ok button 11 Load Default Mode is Mode Rest Press Load Default Mode and choose Load Default by UP amp DOWN it will be s
4. 230W 7R BEAM SPOT WASH 3IN1 MOVING HEAD LIGHT MJ 1020 User Manual Thank you for choosing our beam spot Wash moving head light For the sake of your safety Please read and follow these instructions carefully and keep this manual in a safe place for future reference sepa ating Beamspot 230 MJ 1020 User Manual ver1 0 Catalogue Chapter Page Safe Usage Of The Product 3 Install The Equipment 4 Fitting The Lamp 4 Power Code Connection 5 DMX Connection gt 5 DMX Terminator nasa 6 Function Set 6 Operation Menu o ono nn nnn nnn nnn nn nnn nnn 7 Maintenance o lt gt 10 Keeping The Product Clean 11 Trouble Shooting 11 Equipment and Appendix
5. 95 Y Connection between the controller and a projector and between one projector and another must be made with a 2 core screened cable with each core having at least a 0 5mm diameter Connection to and from the projector is via cannon 3 pin which are included with the projector XLR plugs and sockets The XLR s are connected as shown in the figure above Note Care should be taken to ensure that none of the pins touch the metallic body of the plug or each other The body of the plug is not connected in any way The XLED 590 accepts digital control signals in protocol DMX512 1990 Connect the controller s output to the first fixture s input and connect the first fixture s output to the second fixture s input and connect the rest fixtures in the same way Eventually connect the last fixture s output to a DMX terminator as shown in the figure below www mjledlighting com Nn Beamspot 230 MJ 1020 User Manual ver1 0 DMX IN DMX OUT DMX IN DMXIN DMX CONTROLLER DMX TERMINATOR DMX Terminator In the Controller mode at the last fixture in the chain the DMX output has to be connected with a DMX terminator This prevents electrical noise from disturbing and corrupting the DMX control signals The DMX terminator is simply an XLR connector with a 120Q ohm resistor connected across pins 2 and 3 which is then plugged into the output socket on the last projector in the chain The connectio
6. Control Lamp Control 17 Pan Tilt Speed 18 FUNCTION UNUSED Colour Rotation Speed 19 Dimmer Prism Frost Speed 20 Gobo Speed Technical Parameters Voltage 100 240V 50 60Hz Power consumption 380W 220V Bulb Arclite MHD7R230 230W projection lamp Lamp Arclite 230W Color temperature 8500K Color 14 color White Gobol Srotating gobo White Gobo2 14 fixed gobo White Prism rotation 3 face prism Bilateral rotation frost function Dimmer 0 100 linear adjustment Strobe 0 5 9 times second Beam angle parallel beam angel 15 30 Channel 16 20CHS Control mode DMX512 Automatic and Master slave mode Pan X axis 540 automatically accurate positioning Tilt Y axis 270 automatically accurate positioning Control Panel Touch LCD display panel Protection grade IP20 Gross Weight 19 5 kg Package Size 450 x 430x 530cm www mjledlighting com
7. al installation conforms to all relevant standards Do not connect this device to any other types of dimmer apparatus Make sure that the power cord is never crimped or damaged by sharp edges Never let the power cord come into contact with other cables Only handle the power cord by the plug Never pull out the plug by tugging the power cord Keep the light clean Do not touch the light glasss with bare hands The product should always be installed with a secondary safety fixing On the projector base brink there is a hole for the safety cord provided It should be attached as shown in installing the projector section The lamp used in this projector is a discharge lamp After switching off don t attempt to restart the projector until lamp has cooled this will require approx 15 minutes Switching the lamp on and off at short intervals will reduce the life of both the lamp and the projector But occasional breaks will prolong the life of the lamp and projector Never run the projector without a lamp The light shall be changed if it has become damaged or thermally deformed or reached its life limit Shields and lens shall be changed if they have become visibly damaged to such an extent than their effectiveness is impaired for example by cracks or deep scratches Exterior surface temperatures of the luminaire after 5 minutes operation is Os wrensteady state is achieved 140 There is no user serviceable parts inside the projector do not
8. cket on Replace the lamp Although shines but the moving head Check the digital start address and also check the lamp doesn t accept the instruction of connection situation of the communication control line the controller The moving head lamp only can work Inspect the power supply and voltage is whether normal intermittently Make sure the fan is working well or fans and their filters not blocked Defective projection Make sure the lamp is within its life limit Remove dust or grease from the lenses The beam appears dim heck the optics is clean or the lens in good condition not cracked Replace with a new lamp of the specified type and rating yx Other maintain work should by the specialist which has the experience to carry on Equipment and Appendix yx 230W 7R Moving Head Light Ipcs yx Power Cable pcs 3 XLR connector lunit yx Light Hook 2pcs yx The Product of Instruction lpcs www mjledlighting com Cy Mega LED Lighting Channel List 16 20CH Beamspot 230 MJ 1020 User Manual ver1 0 Channel CHANNEL MODE 16CH 20CH 1 Colour Wheel Colour Wheel 2 Stop Strobe Stop Strobe 3 Dimmer Dimmer 4 Gobo1 Gobo1 5 Gobo Rotation Gobo Rotation 6 Gobo2 Gobo2 7 Prism Prism 8 Prism Rotation Prism Rotation 9 Focus Focus 10 Pan Pan 11 Pan Fine Pan Fine 12 Tilt Tilt 13 Tilt Fine Tilt Fine 14 Frost Frost 15 Reset Reset 16 Lamp
9. e Stop Strobe Dimmer Gobo Change Gobo Rotation Prism Insertion Prism Rotation Focus je 5 Pan Fine Tilt Tilt Fine Frost Reset Lamp Control Pan Tilt Time Colour Time Beam Time Gobo Time n co o 9 U y e O gt y fab D gt Q D Hina a Colour Wheel gt 0 255 Stop Strobe gt 0 255 www mjledlighting com O sepa ating Beamspot 230 MJ 1020 User Manual ver1 0 Dimmer gt 0 255 Gobo Change gt 0 255 Prism Insertion 0 255 0 255 0 255 0 255 0 255 0 255 0 255 0 255 0 255 0 255 0 255 0 255 0 255 0 255 ON OFF Prism Rotation Static Gobo Change tf Frost m Focus Pan Pan Fine Tilt Tilt Fine Pan Tilt Time Colour Time Idd Beam Time Gobo Time Gobo Rotation Lamp Control gt __ password y gt Sub menu include Set Up Information Manual Advanced Model gt Set Up Press Set UP and choose Man control by UP DOWN it will be show Run Mode DMX Address Channel Mode Invert Pan Invert Tilt Swap Pan Tilt Encoder Pan Tilt No DMX Signal Display Power Save Turn On Startup Load Default to confirm by press OK button 1 Press Run Mode and choose Run Mode by UP amp DOWN it will be show DMX and Auto mode to confirm by press Ok button Press DMX Address Mode and choose DMX Address by UP amp DOWN it will be show DMX Address 001 512 to confirm by press Ok button Press
10. how Ok Cancel to confirm bypress Ok button gt Information Press Information and choose by UP DOWN it will be show Software Version Total Fixture Hours Partial Fixture Hours Total Lamp Hours Partial Lamp Hours DMX Monitor System Errors mode gt Manual Press Manual and choose Manual by UP DOWN it will be show Rest Colour Wheel Stop Strobe Dimmer Gobo Change Prism Insertion Prism Rotation Static Gobo Change Frost Focus Pan Pan Fine Tilt Tilt Fine Pan Tilt Time Colour Time Beam Time Gobo Time Gobo Rotation Lamp Control to confirm by press OK button 1 Rest Model is the light rest 2 Colour Wheel Stop Strobe Dimmer Gobo Change Prism Insertion Prism Rotation Static Gobo Change Frost Focus Pan Pan Fine Tilt Tilt Fine Pan Tilt Time Colour Time Beam Time Gobo Time Gobo Rotation model are Press the Ok then pressing UP DWON button will show 001 to 255 correcting by OK Button 3 Lamp Control Press the OK then pressing UP DWON button will show ON to OFF correcting by OK Button gt Advanced Advanced mode is the factory mode Maintenance To prolong the life of the projector some maintenance work has to be done to ensure the optical system in good condition If the projector does not function check the fuses on the power socket of the projector they should only be replaced by fuses of the same specification Should these be da
11. maged call a qualified technician before replacement The projector has thermal protection device that will switch off the projector in case of overheating Should either of these operate check that the fans are not blocked and if they are dirty clean them before switching on the projector again Check that the fans are operational if not call a qualified technician yx Any maintenance work should only be carried out by qualified technicians www mjledlighting com ly Mega LED Lighting oe Beamspot 230 MJ 1020 User Manual ver1 0 Keeping The Product Clean To ensure the reliability of the projector it should be kept clean It is recommended that the fans should be cleaned every 15 days The lens and dichroic colour filters should also be regularly cleaned to maintain an optimum light output Do NOT use any type of solvent on dichroic colour filters Cleaning frequency depends on the environment in which the fixture operates damp smoke or particularly dirty surroundings can cause greater accumulation of dirt on the unit s optics A soft cloth and typical glass cleaning products should be used for cleaning It is recommended to clean the external optics at least once every 15 days and clean the internal optics at least once every 60 90 days Do not use any organic solvent e g alcohol to clean housing of the apparatus Trouble Shooting Problem Answer The moving head light doesn t switch Check the fuse the power so
12. ns are illustrated below DMX TERMINATOR CONNECTION Connect a 120 OHM resistor across pins 2 and 3 in an XLR plug and insert it into the DMX out socket sy d on the last unit in the chain IN 3 3 PIN XLR Function Set 1 Touch Operation a i www mjledlighting com 6 ly Beamspot 230 MJ 1020 User Manual ver1 0 2 Button Opertion UP O Back Q Back Q DOWN Use button switch and LCD display can set the address code and function code easily Check or modify lighting function settings Press the Set UP or OK button LCD display panel will display main menus Function operation menu all have corresponding submenu Each menu all represent the specific functions of lamps specific see below operation menu section Set or browse function setting of lamp Press UP or DOWN key Press OK key to save your changes or to enter submenu Press UP or DOWN can change value Plus or reduce number Operation Menu gt Menu Structure chart Main Menu Sub Menu gt AUTO Comares Jose Coast o Kepa gt amorr C mam J oor C oean gt oo Cenador Perm owo Crop Sora gt Creemos Display Power sae gt omorr monse J gt owo C oeat Je aa www mjledlighting com ly A Beamspot 230 MJ 1020 User Manual ver1 0 Cuat Je romania gt Ciao Cairo tin J e rara Fu reus gt oa arera J 0 Caras Lamp tious gt Cm Koro roren un Jens wr
13. open the housing and never operate the product with the covers removed If you have any questions don t hesitate to consult your dealer or manufacturer A Always disconnect from the mains when the device is not in use or before cleaning it or before attempting any maintenance work www mjledlighting com oe y moon oti Beamspot 230 MJ 1020 User Manual ver1 0 Install The Equipment _ CLAMP i A WARNING EI mr SAFETY CORD To pass the SAFETY CORD i ZTT d Through this HOLE forsafety HOLE FOR SAFETY CORD Use 2pcs clamp and 1safety cord need to purchase Use clamp fix with light hook which in the packing box with light then use screw install to the bottom of lamp Hang the fixture on the structure and fasten the screws attached to each clamp Make sure the light is installed reliable and confirm the light which you fixed is strong enough for hanging the light Base on safety reason please according to the above picture using safety wire cross the light to make it strong enough again Warning 1 Unlock the PAN and TILT before the 1st application of the light for safety 2 Hook and clamp only use for hanging the light Do not use clamp as a tool to move fixtures 3 Base on safety reason please use the safety cord which can afford the weight ten times of lamp through Insurance hole for auxiliary hanging 4 Don t use the handle of the moving head light to fixed or lift Fitting The Lamp Loosen
14. y also cannot the related consequence which causes regarding these information be responsible www mjledlighting com N ly Z Beamspot 230 MJ 1020 User Manual ver1 0 SAFE USAGE OF THE PRODUCT When unpacking and before disposing of the carton check there is no transportation damage before using the product Should there be any damage caused by transportation consult your dealer and do not use the apparatus The product is for indoor use only IP20 Use only in dry locations Keep this device away from rain and moisture excessive heat humidity and dust Do not allow contact with water or any other liquids The product is not designed or intended to be mounted directly on to inflammable surfaces The product is only intended for installation operation and maintenance by professional person The product must be installed in a location with adequate ventilation at least 50cm from adjacent wall surfaces Be sure that no ventilation slots are blocked Do not product the beam onto inflammable surfaces minimum distance is 12m Avoid direct exposure to the light from the lamp The light is harmful to the eye Do not attempt to dismantle or modify the projector in any way Electrical connection must only be carried out by qualified personnel Before installation ensure that the voltage and frequency of power supply match the power requirements of the projector It is essential that each projector is correctly earthed and that electric
Download Pdf Manuals
Related Search