User Manual
Contents
1. To clean the reflective tape apply a minimal amount of diluted neutral cleansing agent that does not contain a polishing compound to a soft cloth and wipe Never use a solvent such as thinner Use a soft cloth so that the surface of the reflective tape does not become scratched 3 Cleaning the electronic pen To clean the electronic pen use a diluted neutral cleansing agent that does not contain a polishing compound Do not apply the neutral cleansing agent directly but rather dampen a soft wet cloth with a mixture of water and the cleaner and wipe Never use a solvent such as thinner Do not allow the pen tip to get wet 3 5 Replaceable Parts 1 Stylus pen Q AAA alkaline battery 3 Spare pen tip For details on obtaining them contact your dealer or a support center 3 9 English StarBoard FX DUO 77 Appendix 3 6 Product Warranty Policy 1 During the free warranty service period if a malfunction occurs during normal use the malfunction will be corrected without charge according to the provisions of the warranty Furthermore if the customer registration card accompanying the warranty is not returned to our company the customer information will not be registered so free repairs might be unavailable After receiving this product please immediately fill out and return this customer registration card 2 The warranty coverage is listed in the following table Product Name Part Name Warranty Coverage StarB2. Check if bright band is seen in the center of the image If not seen press Search button If OK press Next button vpos 383 4 Press 1 Adjust under STEP2 L Camera optical axis When the optical axis adjustment ends press 2 Next LSaDry Camera Adjustment Wizard 02100199902 STEP 2 L Camera optical axis K Start gt step1 L Camera height gt step2 L Camera optical gt step L Camera sensitivity gt step4 R Camera height gt step5 R Camera optical axis gt step6 R Camera sensitivity gt Finish Fine tuning axis Press Adjust button 3 5 English StarBoard FX DUO 77 Appendix 5 Press Next under STEP3 L Camera sensitivity LSaDry Camera Adjustment Wizard 02100199902 STEP3 L Camera sensitivity K Start gt step1 L Camera height gt step2 L Camera optical axis gt step3 L Camera gt step4 R Camera height gt step5 R Camera optical axis gt step6 R Camera sensitivity gt Finish Adjusting sensitivity Press Adjust button 6 Press 1 Search under STEP4 R Camera height When the search ends press 2 Next LSaDry Camera Adjustment Wizard 02100199902 STEP4 R Camera height K Start gt step L Camera height gt step2 L Camera optical axis gt step L Camera sensitivity gt step4 R Camera gt step5 R Camera optical axis gt step6 R Camera sensitivity gt Finish Check if bright band is seen
3. 2 2 1 Inserting the Battery Perform the preparations for using the electronic pen CAUTION Be sure to install batteries correctly Do not install batteries with positive and negative terminals reversed or use batteries other than the type specified Failure to comply may result in overheating or damage to this product Be sure to provide insulation during disposal Be sure to insulate the positive and negative terminals of the battery using cellophane tape or similar material when disposing of batteries Disposing of batteries without insulating them may lead to overheating bursting or ignition due to shorting resulting in personal injury or fire Furthermore be sure to follow all local rules and regulations regarding proper battery disposal 1 Insert the battery into the electronic pen 1 Open the battery cover by moving it in the direction of the arrow 2 As shown in the figure insert the AAA alkaline battery so that the side faces the outside 3 Close the battery cover by moving it in the direction of the arrow 2 4 English StarBoard FX DUO 77 How to Use 2 2 2 Using the Electronic Pen To use the electronic pen to draw characters or images place the tip of the electronic pen on the board and then move the pen When you release the tip of the electronic pen from the board the writing is complete Be careful of the following two points when using the electronic pen 1 When draw
4. it If this does not solve the problem restart the PC The following Touch Sensor Error appears LSaDrv Touch Sensor Error fk Insufficient USB bandwidth Try to use another USB port If it doesn t work use dedicated USB 2 0 hub for each sensor or add USB control board Is a high speed USB device connected to the USB host controller used to connect the StarBoard Be sure to connect the StarBoard and any high speed USB devices to separate USB host controllers Be sure to use a USB hub in the case of PCs with only one USB host controller 3 1 English StarBoard FX DUO 77 Input Related Problems Appendix Problem What to check What to do The input position does not match Has position alignment been performed properly Perform proper position alignment Other than the above Contact a support center The position cannot be aligned properly Have the StarBoard and projector been placed in the proper orientation Adjust the position of the StarBoard and the projector If undue correction is performed it may not be possible to align the position properly Is the PC screen being projected inside the StarBoard s input area Make sure the PC screen projection is contained within the StarBoard s input area For details on the input area see page 1 5 of this User s Guide StarBoard Software files may be broken or installation may not be c
5. no condensation Do not set up in locations subject to vibration and or shock of impact Vibration and or shock of impact may harm internal components of this product resulting in damage to it Do not set up this product in a location subject to vibration or shock of impact Do not set up this product near a high voltage line or power source If this product is set up near high voltage lines or power sources it might receive interference Pee BP D Do not set up in a location subject to direct sunlight or near a heater Failure to comply may result in deformation of or damage to this product 6 Precautions Regarding Disposal AN WARNINGS At time of disposal handle this product as industrial waste according to all applicable laws and regulations When disposing of this product the user should follow all laws and regulations of the locality in which it is being used 9 English StarBoard FX DUO 77 Safe Handling Careful thought was given to the cautions on this device and in this User s Guide However unanticipated circumstances might occur When operating this product users themselves must exercise caution as well as follow instructions Precaution Contents Page s Tighten the screws securely Failure to comply may cause the stand to collapse resulting in personal injury P 1 8 or may cause damage to this product due to shock of impact from the board falling Tighten t
6. he De ce 2 4 2 2 2 Using the Electronic Pen crono nooo a ccoo nrnn rr nn nana anna 2 5 2 2 3 Basic Operations of the Electronic Pen eee en 2 6 2 2 4 Customizing the Electronic Pen nene nana 2 6 23 Start Method E A ii elia lie 2 7 2 3 17 Start Method une sea ON alan ila i i a i 2 7 REDES LS TS h D PRA RR N RIS 092 3 1 Troubleshooting ics assolo aa a eni a Lena 3 1 3 2 Adjusting the Sensor na nana an anna aae a 3 4 3 2 1 Items to Check Before Making Sensor Adjustments e 3 4 3 2 2 Sensor Adjustment Procedure anna na nana 3 4 3 3 System Specification a a ES La da es 3 8 3 4 Proper Care and Cleaning i 3 9 3 5 Replaceable Parts eee nenea aa na na aaa aAa nana 3 9 3 6 Product Warranty Policy nenea a a i a a a ai 3 10 11 English StarBoard FX DUO 77 English StarBoard FX DUO 77 Introduction 1 Introduction 1 1 Preparations This chapter describes the preparations to be made before using StarBoard First time users of StarBoard should read through this chapter 1 1 1 Product Outline The StarBoard FX DUO 77 is an extremely convenient and easy to use electronic whiteboard After setting up the provided software on a PC that is connected to a projector you can use your finger or the stylus pen that is included with the product to operate the PC or import to the PC
7. in real time characters or images that are drawn on the whiteboard 1 1 2 Features You can use your finger or the pen to operate the PC You can use your finger or the pen to operate a PC screen that is projected onto the board with a projector Two pen types are available the stylus pen that is included with the product and an electronic pen that is option When the term pen is used in this User s Guide it means electronic pen You can write directly onto the PC screen After installing the provided StarBoard Software onto a PC you can use your finger or the pen to write characters or images directly onto the PC screen The input characters or drawn images are imported as digital data in real time into the PC where they can be saved or printed Available immediately after starting the PC After the provided StarBoard Software is installed onto the PC StarBoard can be used as soon as the PC is started Compatible with PowerPoint presentations Characters or images can be written into presentations created with Microsoft PowerPoint which significantly improves the expressive power of the presentations StarBoard can also be used in teleconferencing You can also write on video images Characters or images can be written onto captured video image displays This makes it easy to use video materials in lessons or presentations 1 1 English StarBoard FX DUO 77 Introduction 1 2 Parts Check After unpacking make sure th
8. malfunction in this product caused by the connection to this product of equipment other than the equipment specified by our company In the event that there is no abnormality in this product but a defect in a part other than this product was detected or remedied In the event of ordinary wear and tear wear deterioration etc of consumables even during normal use 3 10 English StarBoard FX DUO 77 Appendix 10 If this product malfunctions review the contents of this user s guide If the problems remain irreparable contact the dealer The dealer will determine whether or not the product must be repaired so please contact them If the customer sends the product to our company without RMA Return Merchandise Authorisation number it might not be covered by warranty As a rule the customer is responsible for shipping charges required to send all or part of the product for repair etc Our company will assume responsibility for the return shipping to the customer This warranty does not cover labour fees for repair associated equipment assembly or disassembly Incidental damage caused by the failure of this product e g loss of profit that should have resulted from the use of this product is outside the scope of this warranty The aforementioned provisions define this warranty and they supersede those of all express or implied warranties that include legal defect liability This warranty is limited to us
9. spot Drag Push the pen tip onto the board with sufficient force and without releasing it away from the board move it from one point to another 2 2 4 Customizing the Electronic Pen The electronic pen has one pen tip button and three side buttons Mouse actions can be assigned to these four buttons The default button settings are shown in the following table Button Name Function Pen tip Left click L Side button No 0 Left double click R Side button No 1 Right click C Side button No 2 Hides displays the StarBoard Software Toolbar The side button settings can be changed In the StarBoard Software Main Screen select Settings gt Pen Settings Configure Pen Buttons 2 6 English StarBoard FX DUO 77 How to Use 2 3 Start Method 2 3 1 Start Method 1 Connect the devices with reference to the connection method on page 1 15 2 Turn on the power switch of the projector 3 Turn on the power switch of the PC to start Windows 4 Adjust the position of the projector so that the Windows screen projected by the projector is within the input area refer to page 1 5 of this User s Guide 5 Start the StarBoard Software StarBoard Software does not start when Windows starts unless Startup is selected in the shortcut creation step during the software installation process In this case start the StarBoard Software manually Starting the StarBoard Software manually Select Start Pro
10. the above checks perform adjustments according to the steps given in item 3 2 2 Sensor Adjustment Procedure 3 2 2 Sensor Adjustment Procedure 1 Press the Adjust Camera button on the LSaDrv Touch Sensor Error dialog box displayed on the PC screen LSaDrv Touch Sensor Error x Something seems to be on the touch area or the cameras are not correctly adjusted This may cause an area incapable of touch detection on the screen Please check Manual Startup To start the sensor adjustment wizard manually execute LsCamWiz exe found in C Program Files Hitachi Software Engineering FX DuoDriver 3 4 English StarBoard FX DUO 77 Appendix 2 Camera Adjustment Wizard Start window appears Press Next LSaDry Camera Adjustment Wizard 02100199902 Start Start gt step1 L Camera height gt step2 L Camera optical axis gt step L Camera sensitivity gt stepd R Camera height gt step5 R Camera optical axis gt step6 R Camera sensitivity gt Finish Starting camera adjustment Press Next button E pea VE 3 Press 1 Search under STEP1 L Camera height When the search ends press 2 Next LSaDry Camera Adjustment Wizard 02100199902 STEP1 L Camera height K Start gt step1 L Camera gt step2 L Camera optical axis gt step3 L Camera sensitivity gt step4 R Camera height gt step5 R Camera optical axis gt step6 R Camera sensitivity gt Finish
11. StarBoard FX DUO 77 Notices Reproduction or reprinting without permission of this User s Guide or any part thereof is prohibited The contents of this User s Guide are subject to change without prior notice Every effort has been made to ensure that this User s Guide is complete and correct However should any questionable points mistakes etc come to your attention please inform the vendor Hitachi Software Engineering Co Ltd assumes no responsibility for losses resulting from or related to the use of this product Refer to 3 Appendix 3 6 Product Warranty Policy at the end of this User s Guide for details on the warranty and liabilities Disclaimers Hitachi Software Engineering Co Ltd assumes no liability and makes no warranty either express or implicit regarding the contents of this User s Guide Also the company makes no warranty as to the product s suitability merchantability or fitness for a particular intended use All products of Hitachi Software Engineering Co Ltd described in this User s Guide are presently for sale or are site licensed Users who purchased the aforesaid product s will bear the costs of all required services repairs and damages resulting from defects in this product and will bear the costs of direct or indirect damages including the loss of profits or required information that resulted from the product defects Moreover Hitachi Software Engineering Co Ltd retains the right to revise
12. USB cable to the PC When viewing the central region of the digitiser storage area page 1 5 from the bottom is the LED lit green Check the USB cable connection Did you start the system in the correct sequence Start the system in the correct sequence For details on starting the system see page 2 7 of this User s Guide StarBoard Software files may be broken or installation may not be complete correctly Uninstall the StarBoard Software and then re install it For details on installing StarBoard Software see the StarBoard Software x x User s Guide Other than the above Contact a support center The following Touch Sensor Error appears LSaDrv Touch Sensor Error x Something seems to be on the touch area or the cameras are not correctly adjusted This may cause an area incapable of touch detection on the screen Please check Adjust Camera Is something blocking light from reaching the board surface or reflective tape Remove the blockage Is the reflective tape dirty Wipe away any soiling on the reflective tape Other than the above Adjust the sensor See page 3 4 of this User s Guide The following Touch Sensor Error appears LSaDrv Touch Sensor Error amp 9 USB error 2 Reset the controller If it doesn t works Reboot the computer The controller must be reset and the system restarted Disconnect the USB cable and reconnect
13. at all the following parts are present 1 2 1 StarBoard 1 Parts No Name Qty 1 StarBoard 2 Pen holder with installation part 3 Stylus pen 4 Wall mounting bracket 5 StarBoard Software x x CD ROM 1 6 FX DUO 77 User s Guide this manual 7 Warranty Sheet 1 1 The term x x as used in this User s Guide denotes the same version as the software di IO IN ele that is provided with the accessories 1 2 CO COOOOCOOOOOOOIOOD 5 6 7 1 2 English StarBoard FX DUO 77 Introduction 1 2 2 Stand option 1 Parts No Name Qty 1 Stand vertical support 2 2 Stand crossbar 2 3 Stand foot with casters 2 4 Board receiving bracket left hand version 1 5 Board receiving bracket right hand version 1 6 Board fixing bracket 2 7 Hex socket head cap screw with collar 8 8 Hex socket head cap screw 4 9 Pan head screw 8 10 Triangular knob screw 2 1 2 3 4 5 Sl lee 6 7 8 9 10 2 Accessories No Name Qty 1 Hexagon wrench 1 2 Hexagon wrench holder 1 2 is used to prevent the loss of the Hexagon wrench Hang it from an appropriate place on the stand 1 2 A rr 1 3 English StarBoard FX DUO 77 Introduction 1 2 3 Electronic Pen option 1 Parts No Name Qty 1 Ele
14. at to do if the product breaks or the USB cable is damaged If this product breaks or the USB cable becomes damaged for some reason immediately disconnect the USB cable from the PC and contact a support center Continued operation without repair may result in emission of a strange odor or smoke 3 Precautions Regarding Handling AN WARNINGS Do not hang from or climb on this product Failure to comply may result in personal injury if the product falls collapses or breaks into pieces Be particularly careful in the case of small children d JONS Q UA Do not splash with water or chemical compounds Do not place this product in a location subject to contact with water droplets or place any containers containing water or other chemical compounds on top of or nearby this product Failure to comply may result in damage or fire if water or chemical compounds get inside this product Do not touch this product if you hear thunder Failure to comply may result in electric shock VO Do not mix old and new batteries or use batteries other than those specified Failure to comply may result in fire personal injury and or soiling of the surrounding area due to batteries bursting or leaking fluid 6 English StarBoard FX DUO 77 Safe Handlin CAUTIONS Disconnect the USB cable during extended periods of non use For safety reasons disconnect the USB cable if the product is not going t
15. ctronic pen 1 2 AAA alkaline battery 1 3 Spare pen tip 2 3 English StarBoard FX DUO 77 1 3 Role of Each Part 1 3 1 1 2 3 4 StarBoard 1 TE Introduction 2 7 6 Digitiser Storage Area Receives information regarding characters or images drawn with the pen or the user s finger and transmits this data to the PC Function Area Left and Right Shortcut buttons for functions that are frequently used in applications are located here Refer to the next page for details Input Area Characters or images drawn in this area are imported into the PC When using the StarBoard in Projection Mode make sure that the image projected from the projector is kept within this area USB Cable Used to connect the StarBoard with the PC Ca nni 5 6 1 5 4 Casters These are the casters for moving the board After setting up the StarBoard be sure to lock the casters Lift up the tab to unlock a caster and press down the tab to lock it Locked Unlocked Pen Holder Keep the pen in the pen holder when you are not using it Reflective tape Inner Side of the Frame Reflects light Used to capture pen or finger Operations English StarBoard FX DUO 77 Introduction 1 3 2 Function Area The function area is provided with shortcut keys for the functions that are frequently used in the StarBoar
16. d Software Use by clicking the middle of the symbol with your pen or finger With the exception of touch mode pen mode selection and one time right click you can customise the shortcuts with the software Refer to the online help for details The default settings are as follows Symbol Description Select touch mode or pen mode Select Solid Pen black 1 Select one time right click 1 2 Select Solid Pen red Hides displays the StarBoard Select Solid Pen blue Star Board Software Toolbar hide un hide Adds a new blank page Show previous page Show next page Switch to PC Operation These buttons cannot be customised About one time right click Select Solid Pen green Select Fluorescent Marker Pen Select Eraser Customisable button 1 Calibration is set as the default Customisable button 2 When the one time right click function button is pressed the next finger or electronic pen input becomes right click operational one time only After the function button is pressed the one time right click operation is not canceled until a finger or electronic pen input is made English StarBoard FX DUO 77 Introduction 1 3 3 Electronic Pen option 1 Battery cover Open the cover when inserting or replacing the battery Refer to page 2 4 in this User s Guide for details 2 Side buttons Operations such as right click and scrolling can be assig
17. e of this product within the country where the user bought this product 3 11 English
18. grammes StarBoard Software StarBoard Software or double click the StarBoard Software icon on the desktop A StarBoard Software icon will not be created on the desktop unless Desktop is selected in the shortcut creation step during the software installation process If the No connection icon in below appears on the Tasktray it means that the StarBoard is not connected Make sure that the StarBoard and the PC are properly connected Connected No Connection ig If the StarBoard is properly connected the icon changes to Connected as above If the icon does not change despite correcting the connection there may be some other problem For details refer to 3 Appendix 3 1 Troubleshooting on page 3 1 of this User s Guide If the cursor location deviates from the pen tip perform calibration In the StarBoard Software Main Menu select Settings Calibration OK Or StarBoard Settings StarBoard gt Calibration when using Toolbar Mode 2 7 English StarBoard FX DUO 77 English StarBoard FX DUO 77 3 Appendix 3 1 Troubleshooting Appendix Before assuming the product is broken be sure to check adjustments proper handling procedures the possibility of faulty cable connections etc Recognition Related Problems Problem What to check What to do The StarBoard does not recognise input Is the USB cable connected to the PC Connect the
19. he screws securely Failure to comply may cause the board to fall resulting in personal injury or P 1 9 may cause damage to this product due to shock of impact from the board i falling Be sure to use two or more people for this work P 1 9 Failure to comply may cause the board to fall resulting in personal injury or P 1 1 may cause damage to this product due to shock of impact P 1 1 Keep the wall material in mind when installing Installation by means not suited to the wall material in question may result in the board falling P 1 11 Furthermore wall installation may not be possible depending on the wall For details consult with your dealer Keep the wall strength in mind when installing Only use this product after confirming that it is securely attached and will not P 1 11 fall Furthermore be sure to install using a wall mounting bracket capable of supporting a weight of at least 40 kg Do not strike the board forcefully with the stylus pen bend it or apply an excessive load to it P 2 3 Failure to comply may result in damage to the stylus pen or personal injury Be sure to install batteries correctly Do not install batteries with positive and negative terminals reversed or use P 2 4 batteries other than the type specified Failure to comply may result in overheating or damage to this product Be sure to provide insulation during disposal Be sure to insulate the positive and negative terminals of the battery usi
20. ign object falls on top of or inside this product it may lead to personal injury or damage to the product CAUTIONS Do not allow the reflective tape surrounding the board to become dirty or scratched If the reflective tape becomes dirty or scratched it may lead to improper coordinate detection Do not use a USB cable other than the one supplied Use of a USB cable other than the one supplied may result in malfunction Do not place heavy objects on pull on or subject the USB cable to excess heat Failure to comply may result damage to the USB cable Always grasp the plug of the USB cable when connecting or disconnecting Pulling on the USB cable may result in scratching or damage to the cable 0000 082802 Always lock the casters with stoppers on the front side after installing this product Failure to lock the casters may allow the product to move or slide 5 English StarBoard FX DUO 77 Safe Handlin 2 Dealing with Trouble AN WARNINGS amp What to do in case of emission of smoke strange odor or strange noise If an abnormal condition such as emission of smoke strange odor or strange noise happens to occur for some reason immediately disconnect the product s USB cable from the PC Confirm that the smoke or strange odor is no longer being emitted and contact a support center to request repairs Continued operation without repair may result in fire EN Wh
21. in the center of the image If not seen press Search button If OK press Next button 7 Press 1 Adjust under STEP5 R Camera optical axis When the optical axis adjustment ends press 2 Next LSaDry Camera Adjustment Wizard 02100199902 STEP5 R Camera optical axis K Start step L Camera height gt step2 L Camera optical axis gt step L Camera sensitivity gt step4 R Camera height gt step5 R Camera optical gt step6 R Camera sensitivity gt Finish Fine tuning axis Press Adjust button R 3 6 English StarBoard FX DUO 77 8 Press Next under STEP6 R Camera sensitivity LSaDry Camera Adjustment Wizard 02100199902 STEP6 R Camera sensitivity K Start gt step L Camera height gt step2 L Camera optical axis gt step L Camera sensitivity gt step4 R Camera height gt step5 R Camera optical axis gt step6 R Camera gt Finish Adjusting sensitivity Press Adjust button R 9 Press Finish LSaDry Camera Adjustment Wizard 02100199902 Finish Start step L Camera height gt step2 L Camera optical axis gt step L Camera sensitivity gt step4 R Camera height gt step5 R Camera optical axis gt step6 R Camera sensitivity gt Finish Image sensor parameters have been adjusted Press Finish button to save parameters and exit wizard This completes sensor adjustment After making adj
22. ing with the electronic pen keep the pen as perpendicular as possible to the board and apply force sufficient enough to cause the pen tip to retract into the electronic pen 2 A miniature transmitter is embedded in the tip of the electronic pen If you hold the transmitter area of the electronic pen while drawing characters or images the drawing data from the electronic pen might not be transmitted correctly Ifthe characters or images drawn on the whiteboard are not imported correctly into the PC change your grip on the electronic pen and then verify that they are displayed correctly EEN Blocking of the Infrared Beam Electronic pen operations are detected when the digitiser reads the infrared beams that are generated by the pen If the beam between the electronic pen and the digitiser is blocked normal input becomes impossible Avoid blocking them during use 2 5 English StarBoard FX DUO 77 How to Use 2 2 3 Basic Operations of the Electronic Pen In the default setting of the electronic pen the pen tip button is set to emulate the left click button of a mouse While Windows is in operation the following mouse operations can be performed using the pen tip button Click Push the pen tip onto the board with sufficient force and then quickly move the pen away from the board Double click Push the pen tip onto the board with sufficient force and quickly move the pen away from the board two times in the same
23. nding coordinate position Do not operate near lighting that will obstruct the capture of the image This includes Locations where direct sunlight strikes the board surface or comes from the side Locations with white incandescent lighting or strong infrared source directly overhead Depending on installation conditions or sensor property position detection may be off by about 9 mm 2 The electronic pen uses infrared light having the same frequency approx 940 nm Do not operate this product in a location where other equipment fluorescent lighting plasma displays passive sensors etc may emit a similar frequency 3 The expected battery lifetime may vary depending on initial battery conditions humidity and the Operating environment 3 8 English Appendix StarBoard FX DUO 77 Appendix 3 4 Proper Care and Cleaning Clean the StarBoard periodically so that you may use it for a long time to come 1 Cleaning the StarBoard To clean the StarBoard use a soft cloth dampened with whiteboard cleaner or a diluted neutral cleansing agent that does not contain a polishing compound Never use a solvent such as thinner Note that rubbing or striking the StarBoard surface with a finger nail or other hard object may result in scratching 2 Cleaning the reflective tape If the reflective tape is dirty it will affect pen or finger operations Clean the reflective tape periodically or whenever it becomes dirty or soiled
24. ned to these buttons Refer to page 2 6 in this User s Guide for details 1 4 Assembly and Setup When setting up the board keep the following in mind CAUTION Select a level and stable position Do not set it up near equipment that might generate electromagnetic waves or radio frequencies such as radio transmitters televisions copying machines or air conditioners Avoid locations that are dusty that are subject to extremely high or low temperatures or humidity or that are exposed to direct sunlight 1 7 English StarBoard FX DUO 77 Introduction 1 4 1 Stand Setup Method Reconfirm that all the parts are present before assembling and setting up the stand option CAUTION Tighten the screws securely Failure to comply may cause the stand to collapse resulting in personal injury or may cause damage to this product due to shock of impact from the board falling 1 Assemble the stand Assemble the stand according to the following diagram The numbers in the diagram correspond to the numbers in the parts list on page 1 3 7 Long Short Fasten with a f Phillips screwdriver Align both feet with the longer side facing forward Fasten with a Hexagonal 1 8 English StarBoard FX DUO 77 Introduction 2 Install the board CAUTION Be sure to use two or more people for this work Failure to comply may cause the board to fall resulting in pe
25. ng cellophane tape or similar material when disposing of batteries Disposing of P 2 4 batteries without insulating them may lead to overheating bursting or ignition due to shorting resulting in personal injury or fire Furthermore be sure to follow all local rules and regulations regarding proper battery disposal 10 English StarBoard FX DUO 77 Contents Contents 1 Introduction ss amp s525 550c0 20884008 la niasssidicinniinicecasasicnnzicnizocicasicnnnicidiesssasic sesta LoL 1 1 Preparations ii 1 1 1 11 Product Outline pin uri 2224er alal sala ai iaia 1 1 LIZ A ON 1 1 12 PA id dt 1 2 TZT Ro diia 1 2 ASES AO A ARR 1 3 123 Electronico Pen OPD A ei 1 4 1 3 Role of Each Part i idilio Ri alii 1 5 13 10 StarBoard asc allinea ela 1 5 ES A lai iii 1 6 1 3 3 Electronic Pen Option aeea LIL Ree arci 1 7 1 4 Assembly and Setup nono Eaa EE E a ran een 1 7 1 41 Stand Setup Method cc ice citea A ad 1 8 1 4 2 Wall Mounting Setup Method enma an nana aaa 1 11 1 4 3 Pen Holder Setup Method ci IRA i ii 1 13 1 4 4 Equipment Connection Method eee nn na nana 1 15 2 OO ASE sect sea patat oa al 2 1 How to Use Touch Mode na nana an ana nenn nnse nn 2 1 21 1 A RIO 2 1 21 2 PC Operations tata 2 2 2 2 How to Use the Electronic Pen ne nana an ana naanaaaaaee 2 4 22 Inserting the Battery io 2 RA en
26. nsure the safe and correct use of this product and to prevent personal injury and property damage These symbols and their meanings are as explained below Understand the information well before reading the body of the User s Guide ZN WARNING This symbol indicates information that if ignored or applied incorrectly creates the possibility of death or serious personal injury AN CAUTION This symbol indicates information that if ignored or applied incorrectly might result only in personal impairment or physical damage CAUTION This symbol indicates information that if ignored or applied incorrectly might result in physical hazard or abnormal operation A This symbol draws attention to cautions including warnings S This symbol indicates something prohibited This symbol indicates something that must be done 4 English StarBoard FX DUO 77 Safe Handlin 1 Precautions Regarding Operation NWARNINGS Do not make modifications Do not make any adjustments repairs or modifications not given in this User s Guide as doing so may lead to personal injury or damage to the product Do not open or remove the rear cover cabinet or cover to this product Failure to comply may lead to personal injury or damage to the product Refer internal inspections adjustments and repairs to your dealer or support center Do not place objects on top of this product If a fore
27. o be used for an extended period of time Failure to comply may result in fire amp A Handle the connection cable properly Improper handling of the connection cable such as jamming it against a wall undue bending pulling or twisting may result in overheating or damage due to exposure of the conductive core electrical short or severing of the cable 4 Precautions Regarding Moving the Product CAUTIONS Always use two or more people to move this product This product is a very large and heavy precision instrument Always use two or more people and take great care when moving this product Always disconnect the USB cable from the PC when moving this product Failure to comply may result in damage to the USB cable and or the product itself gt oe Do not subject to shock of impact This product is a precision instrument Excessive shock of impact may hinder further operation Take extreme care when moving this product 7 English StarBoard FX DUO 77 Safe Handlin 5 Precautions Regarding Setup Environment WARNINGS Wall mounting work should be performed by a construction specialist Improper work may result in death or personal injury due to the product falling during operation Always use the specified mounting unit Improper assembly may cause the product to fall over There is risk of personal injury if the product falls over Completely tighten the sc
28. oard Digitiser FX DUO 77 Pen Holder Stylus Pen Function Area Sticker Reflective Tape Wall Mounting Bracket Electronic Pen Electronic Pen AAA alkaline battery Spare Pen Tips Stand Explanatory note Covered by warranty excluding wear or physical damage Not covered by warranty 3 Please refer to the warranty sheet for this product s warranty service period 4 Even during the warranty period there will be a repair charge in the following cases 1 2 3 4 5 6 7 8 9 10 If the registration card accompanying the warranty is not returned to our company If the warranty is not presented If specified fields on the registration card accompanying the warranty are not completed or if the wording has been changed without authorisation The warranty applies only to the original purchasers It does not apply to a third party to whom the customer resold this product In the event of a malfunction or damage resulting from the customer s improper handling e g a fall impact etc caused by the customer during transportation or movement In the event of problems resulting from handling contrary to the handling and precautions mentioned in this user s guide In the event of failure or damage resulting from abnormal voltages pollution or other natural disasters e g fire earthquake and lightning In the event of a
29. ody kept sufficiently away so that your palm and elbow do not touch the board If your hand or elbow touches the board or you are within 1 cm of the board it might cause an incorrect operation O X 2 1 English StarBoard FX DUO 77 How to Use Using your finger Extend your finger and touch the board In the same way as the stylus pen if you touch the board with anything other than your finger or you are too close to the board it might cause an incorrect operation 2 1 2 PC Operations When performing PC operations by pointing or giving presentations without inputting characters it is convenient to extend the stylus pen and use it as a pointer 2 2 English StarBoard FX DUO 77 How to Use CAUTION Do not strike the board forcefully with the stylus pen bend it or apply an excessive load to it Failure to comply may result in damage to the stylus pen or personal injury CAUTION Keep the stylus pen in the pen holder when not in use If you leave it on the reflective tape it might cause a sensor error or incorrect detection 2 3 English StarBoard FX DUO 77 How to Use 2 2 How to Use the Electronic Pen This section gives a basic description of how to use the electronic pen option
30. omplete correctly Uninstall the StarBoard Software and then re install it For details on installing StarBoard Software see the StarBoard Software x x User s Guide Other than the above Contact a support center The electronic pen does not work This may be due to faulty contact of electronic pen batteries Remove the batteries from the electronic pen and re install them Are batteries used up Replace the batteries For details on battery replacement see page 2 4 of this User s Guide StarBoard Software files may be broken or installation may not be complete correctly Uninstall the StarBoard Software and then re install it For details on installing StarBoard Software see the StarBoard Software x x User s Guide Is there a nearby light source with a wavelength close to that of the electronic pen Illumination from fluorescent lighting or similar source Check by turning off the lights in the room If the StarBoard operates normally change the location in which it is installed or change the lighting fixtures Other than the above Restart Windows and StarBoard Software Contact a support center Check if the same problem arises when using another electronic pen If operations are normal when using another electronic pen the original pen is the problem 3 2 English StarBoard FX DUO 77 Appendix Problem What to check Wha
31. or more people a Remove the triangular knob screw at the bottom of each side b Raise the board and attach the receiving brackets to the square holes at the desired height c Tighten the triangular knob screw at the a c bottom of each side 1 10 English StarBoard FX DUO 77 Introduction 1 4 2 Wall Mounting Setup Method CAUTION Keep the wall material in mind when installing Installation by means not suited to the wall material in question may result in the board falling Furthermore wall installation may not be possible depending on the wall For details consult with your dealer Keep the wall strength in mind when installing Only use this product after confirming that it is securely attached and will not fall Furthermore be sure to install using a wall mounting bracket capable of supporting a weight of at least 40 kg 1 Install the wall mounting brackets Determine the height at which the board will be installed and install the wall mounting brackets on the wall at the positions shown in the following diagram below The wall mounting brackets are provided with the StarBoard 4 on page 1 2 1108 2 mm 247 mm Q000000000000000 BODODODODODODOOO 1 11 English StarBoard FX DUO 77 Introduction 2 Install the board CAUTION Be sure to use two or more people for this work Failure to comply may cause the boa
32. rd to fall resulting in personal injury or may cause damage to this product due to shock of impact Attach the wall mounting brackets to the top square holes both sides of the stays on the back of the board mm as m 1 12 English StarBoard FX DUO 77 Introduction 1 4 3 Pen Holder Setup Method 1 Installation method Insert the pen holder into the rail on the right side on the back of the board and slide it to the desired position O0000 0 lt DO OOo 2 Removal method To remove the pen holder apply pressure to the top of the pen holder and pull it back 1 13 English StarBoard FX DUO 77 Introduction 3 To change the position of the pen holder a Remove the installation part from the pen holder b Insert the installation part into the opposite groove c Insert the pen holder into the rail on the left side on the back of the board and slide it to the desired position a b N 1 14 English StarBoard FX DUO 77 Introduction 1 4 4 Equipment Connection Method Before Starting to Connect Equipment Install the StarBoard Software on your PC before starting to connect equipment The equipment might not operate correctly if it is connected without the software being installed Connect the PC projector and StarBoard according to the following p
33. rews of all individual parts O bb Do not place in a location with flammable or corrosive gas Placing this product in a location where there is flammable or corrosive gas may result in fire or damage to this product There is a particular danger of explosion in the case of flammable gas Do not place in a location with flammable or corrosive gas AN CAUTIONS Do not place in locations subject to excess moisture dust smoke or steam Placement in a location such as next to a kitchen or a humidifier may result in fire or damage to this product Do not touch internally mounted parts Directly toughing internally mounted parts inside this product may result in personal injury or damage to this product E OO Do not use this product near water If water somehow gets inside this product immediately disconnect the USB cable and contact a support center Continued use may result in fire or damage to this product 8 English StarBoard FX DUO 77 Safe Handlin CAUTIONS Regarding the setup environment Set up this product on a level floor surface with a weight bearing capacity of 150 kg m or more and which is made of floor materials that will not deform or become depressed due to movement by casters Do not use this product in locations subject to high temperature or high humidity This product s usage environment conditions Temperature 5 C 35 C Humidity 20 RH 80 RH
34. rocedure StarBoard Power Supply 1 Connect the RGB cable to the projector s RGB connector and fasten with screws 2 Connect the opposite side of the RGB cable to the PC s RGB connector and fasten with screws 3 Connect the USB cable from the lower right of the StarBoard to a USB port on the PC 4 Connect the power supply cables of the PC and projector to the power supply About PC Earth Depending on your PC an incorrect operation might be caused by PC noise via the USB cable If this happens verify that the earth of your PC s power supply cable is connected If the earth is not connected it might cause an incorrect operation 1 15 English StarBoard FX DUO 77 English StarBoard FX DUO 77 How to Use 2 How to Use 2 1 How to Use Touch Mode This section gives a basic description of how to use the board in touch mode 2 1 1 Character Input To input characters use your finger or the stylus that was provided with the product CAUTION Use an input tool with a thickness of least 7 mm When inputting to this product use a tool that is at least 7 mm If a pen or similar tool with a thickness of less than 7 mm is used the input will be unstable Also do not use tools with a sharp tip such as a ballpoint pen If such a tool is used incorrectly it could damage the surface of the board Using the stylus pen Use the stylus pen on the board with your b
35. rsonal injury or may cause damage to this product due to shock of impact Tighten the screws securely Failure to comply may cause the board to fall resulting in personal injury or may cause damage to this product due to shock of impact from the board falling Install the board on the stand assembled in step 1 Install the board according to the following procedure Note that this work should be performed by two or more people The numbers in the diagram correspond to the numbers in the parts list on page 1 3 of this User s Guide a Decide the level out of six at which the board will be installed and attach the board receiving brackets 4 and 5 to the square holes of the stays on the back of the board A oesposscosuquuuo b Verify that the square holes are attached securely to the board receiving brackets on both sides c Tighten the triangular knob screw 10 to fasten the board to the board fixing bracket 6 on both sides 1 9 English StarBoard FX DUO 77 Introduction 3 Adjust the height CAUTION Be sure to use two or more people for this work Failure to comply may cause the board to fall resulting in personal injury or may cause damage to this product due to shock of impact The StarBoard can be positioned at six height levels Adjust the height according to the following procedure Note that this work should be performed by two
36. t to do Electronic pen operation is Is a remote controller for Stop operating the remote controller unstable or stops AV equipment being operated while using the pen The battery charge of the electronic pen may be low Replace the batteries For details on battery replacement see page 2 4 of this User s Guide StarBoard Software files may be broken or installation may not be complete correctly Uninstall the StarBoard Software and then re install it For details on installing StarBoard Software see the StarBoard Software x x User s Guide Other than the above Restart Windows and StarBoard Software Check if the same problem arises when using another electronic pen If operations are normal when using another electronic pen the original pen is the problem 3 3 English StarBoard FX DUO 77 Appendix 3 2 Adjusting the Sensor 3 2 1 Items to Check Before Making Sensor Adjustments The following error may appear while using this product LSaDrv Touch Sensor Error x Something seems to be on the touch area or the cameras are not correctly adjusted This may cause an area incapable of touch detection on the screen Please check Adjust Camera Check the following items if this error appears Check that light is not blocked from reaching the board surface or reflective tape Check that the reflective tape is not dirty If the problem is not corrected despite making
37. this User s Guide and to modify the contents thereof without any obligation to notify anyone 1 English StarBoard FX DUO 77 Product Assurance Provisions This product is limited to use in the country where the user bought this product For warranty details refer to 3 Appendix 3 6 Product Warranty Policy at the end of this User s Guide This Ist edition of the User s Guide FXD EU070621 is for the following products AH00179 StarBoard FX DUO 77 AH00180 FX DUO Electronic Pen K W033 021 Stand Windows is a trademark of Microsoft Corporation U S and in other countries Other trademarks and product names are trademarks and or registered trademarks of their respective holders Manual Creation Dates June 2007 1st Edition FXD EU070621 All Right Reserved Copyright c 2007 Hitachi Software Engineering Co Ltd 2 English StarBoard FX DUO 77 Introduction Thank you very much for purchasing HitachiSoft s StarBoard FX DUO 77 henceforth referred to as StarBoard This User s Guide has been created for people who already have a working knowledge of personal computers henceforth referred to as PC Please make sure that you understand the contents of this User s Guide and use the software correctly We hope that you make the most of this product 3 English StarBoard FX DUO 77 Safe Handlin Safe Handling Markings and Symbols Various markings and symbols are used in this User s Guide and on this product to e
38. ustments check that input can be performed normally Appendix English StarBoard FX DUO 77 3 3 System Specifications Ttem Specification Model name StarBoard FX DUO 77 Detection method Infrared image sensor system Digitiser resolution 0 05 mm Sampling rate Approx 100 points second when using USB 1 1 Full Speed Interface USB 1 1 cable length 2 8 m Effective screen size mm Approx 77 inches 1 573 W x 1 180 H Board dimensions mm 1 739 W x 1 357 H x 69 D not including the pen holder Overall dimensions including stand mm 1 739 W x 1 824 2 174 H x 620 D Power consumption SV 500 mA Weight of main unit weight including stand Approx 24 kg 41 kg Operating requirements 5 C 35 C Humidity 20 80 RH without condensation Storage requirements 10 C 45 C Humidity 20 80 RH without condensation Electronic pen option Communication system Infrared Carrier wavelength 56 kHz IR wavelength 940 nm Side switches 3 Power supply AAA alkaline battery Expected battery life Approx 80 hours of continuous use Size 149 mm x 617 mm Weight Approx 20 g not including batteries Standards etc VCCI Class B FCC Class B CE Using infrared and compact cameras this product captures the image shadow of a pen or finger and detects the correspo
Download Pdf Manuals
Related Search