DC400i Visualiser
Contents
1. USB IMAGE CAPTURE AND VIDEO RECORDING COMPUTER REQUIREMENTS SOFTWARE SPECIFICATION TROUBLE SHOOTING PACKING LIST Page 3 Page o O N O O O 9 10 13 14 20 21 22 23 INTRODUCTION Thank you for purchasing this product with sensible use it will give years of good service Like many of us referring to the user manual is often a last resort so we recommend you make an electronic copy and a hard copy for future reference We have designed the product so that it s easy to understand and operate Most of the core functions can be operated from the Visualiser front panel leaving some of the special functions such as freeze mirror image store and rotate on the remote It s therefore important that you take care of the remote We hope you enjoy using the product 5 Year Warranty Warranties give you peace of mind even so you need to take care of your DC400i and understand what s covered and what s not What s covered In general the unit is covered by a 5 year warranty which takes into consideration failures which are outside of your control What s not covered e Physical damage abuse Fluid ingress e Broken cables due to twisting excessive force For full warranty details please visit www optomaeurope com Compliant The DC400i is RoHS compliant which means it meets the rigorous European Union s requirements for restriction of the use of certain hazardous substances in electrical and electronic equipment Pag2. Optoma DC4001 Visualiser Document Camera Please read this manual carefully before operating the document camera and keep it for reference US E R MAN UAL Page 1 Safety Measures Notice PLEASE READ CAREFULLY BEFORE USE WARNING Risk of elecinc shock Dangerous voltage inside Page 2 Use the document camera Visualiser under the rated electric conditions Do not place the document camera Visualiser on an unstable surface It may fall causing injury or damage Do not place this device directly under sunlight or near heaters Do not place this device near water Keep the camera away from acid or alkali gas Do not place this document camera Visualiser in humid dusty windy or vibrant locations The recommended operating environment is Temperature 0 C 45 C 32 F 113 F Humidity less than 75 Always unplug BEFORE cleaning the device Use a damp soft cloth for cleaning Do not use volatile solvent When this equipment functions abnormally such as smoke smell noise immediately unplug and call for professional assistance Unplug the document camera Visualiser when not in use INTRODUCTION WARRANTY PARTS IDENTIFICATION CONTROL PANEL INPUTS AND OUTPUTS CONNECTIONS REMOTE CONTROL VISUALISER OR VIDEO MODE OPERATING THE VISUALISER FEATURES LIGHT ZOOM IN AND ZOOM OUT FOCUS ADJUSTMENT BRIGHTNESS ADJUSTMENT WHITE BALANCE ADJUSTMENT FREEZE IMAGE MIRROR IMAGE SPLIT SCREEN IMAGE SAVE IMAGE RECALL
3. video mode RES Toggles output resolutions SXGA UXGA 720P and 1080p USB Switch USB functions between Disk mode and Video mode use the buttons and E to select then press HEJ to confirm DEL Press to delete the selected pictures keep pressed for 2 seconds to delete all saved pictures Bright Image brightness control use and ES to adjust Focus Adjust focus manually with jand fj then press to confirm RECALL Press to view your saved images use the buttons and ES to change pages and use buttons and to select your picture choice then press to confirm In recall mode press E3 or to zoom the image in or out You can also use buttons and ES plus H and to move the image The button allows you to take a snap shoot of your image and save this to either SD Card or Internal memory 200 images can be saved to internal memory but a lot more if using a SD CARD the amount is dependent on the cards size i e up to 32 GB AUTO Adjusts white balance and focus automatically Zoom Zoom in out control using or 8 buttons MIR Use this button MIR to flip the camera image Split Use the Split button to have two images on your screen Freeze Use the Freeze Unfreeze button to freeze unfreeze an image TITLE Title freeze mode In this mode you can adjust the position of the frozen title with buttons or EJ and also adjust the size with H or PIP Picture in picture Z Z click to select a saved picture to displ
4. control The DC400i can store up to 200 images in its internal memory IMAGE RECALL Only available from the remote control Click the recall button to view saved images use the buttons Ema and ES to change pages and use buttons and to select your picture choice then press EMM to confirm In recall mode press 8 or E to zoom the image in or out You can also use buttons Ez and ES plus H and to move the image USB IMAGE CAPTURE AND VIDEO RECORDING The USB2 port can be used to store images and video clips from the Visualiser on your computer Note You will need to install the supplied software COMPUTER REQUIREMENTS The PC s hardware and software configurations shall not be less than the following requirements e Operating system Windows XP Win7 Win8 e CPU Pentium 4 1 8Ghz or better e Physical memory 512M or more e Video memory 64M or better Windows XP and Vista do not support USB 2 without a driver so you must install the supplied USB2 driver to get your DC400i working NOTE You can also use the camera as a webcam with software like SKYPE or some other camera software the DC400i will work with the OS built in USB2 drivers Just select USB or UVC Camera device SKYPE also works with Windows XP but you must install the USB Driver located on the DC400i s CD first SKYPE is fully supported under Skype Tools Options Video Settings Use the supplied USB2 cable and connect from the DC400i to a spare USB port on your PC La
5. oF The USB port allows you to view the camera output via the PC You will need to install the PC software which is described later in this manual USB CABLE Once connected this will allow you to record endless pictures and video files depending on your Hard Disk capacity the software also provides simple annotation of images SD CARD CEE You can also save images to an SD Card to review on a PC LAPTOP or any device that reads SD Cards like the ML500 LED projector SD CARD from Optoma the max card size is 32 GB You cannot record video to the SD Card Page 10 Positioning the Camera Rotation amp Mirror Normally the camera is positioned over documents and objects alongside the Visualiser Using the remote control you can rotate EM the image through 90 180 or 270 degree increments so that the captured image appears straight to the viewer You can also use the mirror EI function in a similar way Using the combination of rotation and mirror functions means you have flexibility when positioning the camera Page 11 FEATURES Page 12 fo q LED LIGHT The DC400i uses eco friendly low power LED lamps which are cool to the touch and mercury free Due to the excellent sensitivity of the camera the lamp is seldom required Adjusting the light balance from the remote control can often provide clear vivid images ZOOMING IN AND ZOOMING OUT With 14x optical zoom combined with 16x seamless digital zoom the DC400i enables
6. you to view items in im mense detail DC400i s advanced optical system features high speed auto focus capability that ensures instant auto focus when you quickly zoom in and out of any object You can also manually adjust focus to satisfy any special viewing needs by pressing ZOOM Egor ZOOM 9 FOCUS ADJUSTMENT When the Visualiser is turned on the focus automatically adjusts it is not necessary to re adjust the focus if you are only working with flat materials text photos etc Only 3D objects require a focus adjustment Press the AUTO button to auto focus Press the FO CUS or amp FOCUS buttons to focus manually This function is accessible from the remote control and the base unit BRIGHTNESS ADJUSTMENT You can adjust the camera brightness by pressing the BRIGHT or BRIGHT E buttons This function is only accessible from the remote control WHITE BALANCE ADJUSTMENT Under different lighting conditions you may need to adjust the white balance by pressing the AUTO button The AUTO button also assists with fine focus changes FREEZE IMAGE Use FREEZE to freeze and unfreeze the image MIRROR IMAGE Only available from the remote control ELA The mirror image function gives you a different perspective of an object SPLIT SCREEN Only available from the remote control The split screen offers the capability of comparing two images or comparing two different views of one object side by side IMAGE SAVE Only available from the remote
7. ay on the lower right corner of a screen the image in 90 180 and 270 degrees Rotation Rotate E Visualiser Mode The DC400i defaults to Visualiser mode each time the unit is turned on This is the preferred mode for most applications The DC400i can view amp record video in this mode at 20 30 FPS frames per second If smoother video recording is required then switch to Video Mode Video Mode OPERATING THE VISUALISER Powering on After connecting the external power supply the red led in the center of the DC400i will flash This indicates the unit is in standby mode To start the Visualiser simply press the power on button via the main control panel or the remote control The led will turn to green Please Note It takes 3 4 seconds before the Visualiser is fully powered and ready to use Connecting the Visualiser This is simplicity itself The supplied 15 pin VGA cable connects between the Visualiser and the output devise i e Projector or monitor TV via the 15pin VGA port You can also use HDMI if your projector or panel supports this I O HDMI will give you a far better image and also goes up to 1080p output HDMI VGA CABLE HDMI CABLE Page 9 VGA In VGA In is used to show your desktop on the camera When you run the supplied software and show project onto a white VGACABLE board it allows you to annotate over your image so you can highlight points of interest or draw over the image USB Connection
8. e 4 PARTS IDENTIFICATION Page 5 Parts Identification Camera LED light Flexible camera arm IR receiver for Remote Control Control panel SD Card Slot Interface panel HDMI VGA Out amp Past Through ports plus USB2 Mains Input amp Kensington lock CON OORA GON gt CONTROL PANEL LAMP FOCUS AUTO INPUTS AND OUTPUTS I 0 s Page 6 O00000 00000 00000 Res O Pa O VGA IN VGA OUT HDMI Input Output panel VGA IN VGA RGB signal input 15 pin D SUB VGA OUT VGA RGB signal output 15 pin D SUB HDMI HDMI signal output USB2 USB2 slave used to connect with PC Laptop SD CARD SD card slot 32 GB Max USB Oki FOUCS O a C SD CARD Control Panel Power Turn on off power Auto Auto focus color adjustment and white balance Lamp Turn on off LED light FOCUS Adjust focus manually focus far and focus near BRIGHT Image brightness control ZOOM Image zoom in and zoom out control O OA O Na CONNECTIONS Page cm HDMI USB HDMI CABLE USB CABLE PC or Laptop Panel or Projector Projector or Panel Laptop or PC CONNECTIONS VGA IN VGA in from PC Laptop VGA OUT VGA Out to Panel or Projector HDMI HDMI Out to Projector or Panel USB2 USB2 slave used to connect with PC Laptop REMOTE CONTROL Page 8 Remote Functions Power Power ON OFF FPS Switch the frame rate between 20 Visualizer mode and 30
9. image Page 20 SPECIFICATIONS IMAGE Sensor Pixels Frame Rate Color adjustment Rotation White balance Mirror Image Brightness adjustment Output resolution Image split Image Freeze Video recording Text mode Image capture SD CARD Support Remote Control Kensington Lock OSD OPTICS Focus Shooting area Zoom Page 21 OTHER 1 2 5 CMOS Input 5 Megapixel Output 20 30 Dimensions Yes Weight net 90 180 and 270 degrees Power Supply Auto manual Software Support Yes Yes SXGA 720p UXGA and 1080p Yes Yes Yes via USB Yes Yes 200 images Internal Memory Yes Max 32 GB Yes Yes Yes Auto manual Max 14 7 x11 1 Min 0 1 x0 1 14 x optical 16 x digital VGA HDMI and VGA Setup 6 7 19 1 13 5 Folded 6 7 7 2 13 5 4 4lbs 2kg 12V DC Power Adaptor Microsoft Windows Apple MAC OSX TROUBLE SHOOTING Symptoms Possible causes counter measures No Image Power Cord is not connected Cables are not connected Power is turned off Output resolution not set correct Image Bending Camera is out of line adjust the camera Press AUTO Out of focus or blurring image Object is too close to the lens Focus point is full ZOOM press ZOOM minus to adjust Auto focus is not on press AUTO again Dust or condensation could be on the lens use a soft damp cloth to clean If the problem still remains after checking the above consult your dealer or authorized service persona
10. image shown as below N USB Camera Application ta de _ o i 24 Lo amp j V USB Camera Application uma nt o A Video Zoom Language Setting Device Control Help Video Zoom Language Setting Device Control Help O a Ed X a OE ax a xar gJ TIAA x sr JJA 09 45 46 Line width change the width of the line X Y change the position of the line Color change the color of the line Width Height Change the angle of the line Page 17 Click El to change the setting of the chosen rectangle R P E 1 S USB Camera Application een iol sa ta Lo 8 X USB Camera Application Et x Video Zoom Language Setting Device Control Help Video Zoom Language Setting Device Control Help Type Rectangle Line Width s 7 Fill Color o 238 width 222 221 Height 132 bl E axus JTA A w X 4 no i x Ww ia j i P p pH Lot 4 T if taft 1269 500 Frame 1280 1024 332 316Bytes 09 48 38 127 255 Frame 1280x1024 330 272Bytes 10 11 35 Line width change the line width of the rectangle X Y change the position of the rectangle Color change the line color of the rectangle Fill Color Tick itto fill color in the rectangle Width Height Change the shape of the rectangle by changing the angle of two adjacent lines of the rectangle Page 18 Click to change the settings
11. l Page 22 Package Content Item DC400i Power cord Power adaptor 12V 2A VGA cable USB 2 0 cable Remote control AA batteries User manual CD Microscope Adapter Quantity 1 1 1 Remote Control Page 23 VGA Cable Software User Manual CD Power Adapter USB2 Cable AA Batteries DC400i
12. of the chosen circle Click to place a curve in the image shown as below kalaj 2 X USB Camera Application aq o a sos nata balba Video Zoom Language Setting Device Control Help X USB Camera Application Video Zoom Language Setting Device Control Help aQ unid color D P racoon M s width 335 Height 302 as as xX x E Ep 5 amp E del x xX u w Playing 1149516 Frame 1280x1024 332 100Bytes 10 13 09 f Playing 133 13 10 19 21 Line width change the line width of the circle X Y change the position of the circle Color change the line color of the circle Fill Color Tick it to fill color in the circle Width Height change the size of the circle Page 19 Click FH to change the setting of the chosen curve Click d to change the setting of the graphic X USB Camera Application o Bo R Video Zoom Language Setting Device Control Help Video Zoom Language Setting Device Control Help aQuax no a O idx as S do x Ww axun nJ TAA j ft E a d E gi H Playing 1276 554 Frame 1280x1024 331 684Bytes 10 21 08 4 i 1275 567 Frame 1280x1024 329 912Bytes 10 27 27 7 Line width change the line width of the curve X Y change the position of the Graphic delete curve Color change the line color of the curve di Click x to delete the chosen graphic Click to delete all graphics placed in the
13. ptop Please turn on the DC400i first so the green power on button is on this may take 30 or so seconds then plug in the USB cable so your PC Laptop can detect a new device then run the Optoma USB software Page 13 SOFTWARE START Double click the desktop short cut a then click Device select the right model number as shown below depending on which model you have this will show DC300i or DC400i Image 1 IMAGE CAPTURE AND VIDEO RECORDING to capture images The captured images will be automatically saved into the default destination folder The path and file name are displayed in software sta Left click tus bar on the bottom of the window Image 2 E Image 2 EE cone fp X USB Camera Application 20000807 0000807 90000807 NS TA a X P EY X w xX E G SNA 00066 wil il q ii ill 124 75 Frame 12801024 323 824Bytes 16 28 24 y Recording Time 00 00 07 Size 23MB Path C Users RRJ Documents Videos 2013 02 11 16H31M02s avi ___ O 222 164 Frame 1280x1024 324 912Bytes 16 31 09 Left click Q to start recording During recording the settings button will be inactive DE Detailed information is displayed on the software status bar at the bottom of the window see image 2 Video s are automatically saved in the default folder or pre set folder Page 14 SETTINGS The captured images and recorded videos will be saved into the folders of Images and Videos respectivel
14. y which are created by the system automatically To set a different path where you wish your image s or video saved click on the left side of the window a pop up dialog box appears below Save the captured images into a different folder Click the button next to the select a folder to save picture files text box to set the path for cap tured images Save a recorded video into a different folder and set up parameters for videos Click the button next to the Select a folder to save video files text box to set the path for videos Page 15 IMAGE MODIFY E Click gt you will see this interface e ll a E e nto an pe Lo je V USB Camera Application N USB Camera Application ON Video Zoom Language Setting Device Control Help Video Zoom Language Setting Device Control Help a Qu x a CP dA X d JA at m di C e j 14 4 ax G J JAA ax age vwse ws Ke c0006E1_Z0Y SNAT wil MMT k m e 4 482 277 Frame 1280x1024 322 508Bytes 17 06 33 Frame 1280x1024 335 240Bytes 16 45 41 4 Playing Playing E Graphic selection and move Clicking allows you to create lines within the image Clicking by allows to select and move lines circles etc to a different position within the image Page 16 Click to change the setting of the chosen line Click to place a rectangle in the
Download Pdf Manuals
Related Search