Molift Mover 300 User Manual - Molift Hoists and spare parts
Contents
1. Assembly and disassembly The lifter comes in one cardboard box Verify that the box has no apparent damage If dam aged check the content and contact your deal er for assistance if components are damaged it e The box contains one complete Molift Mover 300 lifter with hand control battery and bat Es DE tery charger with mains cable e Place the battery in the holder with the con nectors facing down Release the emergency Assembly stop and run each function of the lifter to verify e The chassis should be rolled out of the box proper function Always charge batteries be e Charge the battery see page 10 fore the lifter is ut into service Note The battery must not be in the battery e Mount the suspension by turning the opening holder during assembly in the end cover upwards and slide the attach e Place the column in the attachment on the ment fork in place as shown below chassis and push the column down as shown below The screw in front of the column should fit in the slot inside the chassis Make sure that the red arrow on the lower part of the column corresponds with the lock han dle Fix the column with the lock handle If the column is not placed correct the lifter will not work Check that the lifter is mounted correctly with no loose parts or damages Ensure that the suspension and lifting column are properly fixed Checklist after mounting e Check the lifter according to checklist before2. use on page 7 Fix the column by pushing the lock han dle on the back all the way down Connect the hand control cable to the con tact on the underside of the battery holder The hand control has a hook that makes it possi ble to hang it on the drive handle or the plastic hooks on the column Rev D 08 05 2013 BM06101 Molift MOVER 300 English Page 5 of 20 molift by Etac Disassembly Remove the suspension e Run the lifting arm all the way down e Remove the battery to avoid it from falling out during transport e Release the lock handle on the chassis end re move the complete column with lifting arm s e Place the hand control on the drive handle Storage For long time storage it is recommended that the battery is removed and the emergency stop but ton is activated The lifter can be stored and trans ported under the following conditions 6 9 CE Pressure 70 106 kPa Humidity 15 93 Temperature 25 70 C The lifter is designed for use at standard room temperatures 5 to 40 C Following storage or transport at other temperatures leave the lifter in a room with a suitable temperature until it reaches a safe operating temperature Page 6 of 20 BM06101 Molift MOVER 300 English Rev D 08 05 2013 Checklist before use 1 Check that the lifter has no apparent damage or other faults 2 Ensure that the lifting arm and lifting column are properly fixed and that ther
3. Part no 3033300 Part no 3032400 Part no 3033400 XXL Part no 3032500 Part no 3033500 Molift Easy Toilet Sling Comfort head support Molift Easy Amputee Sling Molift Patient Specific Sling With head support Part no 3050100 Part no 3050200 Part no 3050300 Part no 3050400 GP Read the user manual that comes with the sling for specific instructions Bag for slings Part no 3048000 Rev D 08 05 2013 BM06101 Molift MOVER 300 English Sling size guide Easy and Basic Slings Color A B code cm cm cm por write 280 800 26 130 fee pu ewe 160 280 ve rs ee L oreen ooreo 66 100 Joa m verou 4595 56 fes e CA C fes sp jo RO ras 48 e550 Choice of sling size depends on both user weight and shape size of user Page 13 of 20 lift Equipment Quick release suspensions Steel suspensions e 4 point steel Large size 560x350 mm Part no 1430002 e 4 point steel Medium size 450x300 mm Part no 1430001 e 4point steel Small size 350x240 mm Part no 1430009 e 2 points steel Large size 560 mm Part no 1430007 e 2 points steel Medium size 450 mm Part no 1430006 e 2 points steel Small size 350 Part no 1430008 The suspensions can be used on other Molift lift ers with the same quick release If the suspension is mounted on a lifter with lower SWL the lowest SWL will apply Castor with directional lock Part no 1320140 The castor can be cha
4. the temperature rises beyond a critical limit Wait until the lifter has cooled down before using it again e The lifting arm is hinged to prevent the arm and suspension from squeezing the patient if it is lowered too much The actuator will not pro duce any force when moving downwards e The suspension has safety hooks to prevent the sling loops to fall off Emergency stop and lowering Contact your Molift service partner if the rea son for failure causing an emergency lower ing is unknown or if it is a result of failed com ponents or parts Emergency stop The emergency stop will cut the power to the ac tuator and is situated on the battery holder on the lifting column Turning it clockwise until it pops out will reset the emergency button Electrical emergency lowering Emergency stop Rev D 08 05 2013 BM06101 Molift MOVER 300 English molift Electrical emergency lowering It is possible to perform an emergency lowering of the lifting arm in case of a general malfunction of the control electronics The button can be found on the battery holder If you need to perform an emergency lowering move the lifter to a suitable location to lower the user e Press the emergency lowering button The lift ing arm will then perform a smooth downward movement The emergency stop button can not be activated when performing electrical emergency lowering e If the lifter still does not work change battery and try th
5. D Mode Initiation 10 sec Red Fastcharge Green Yellow Top off charge Trickle charge RediGreen Battery capacity The battery lamp on the hand control and on the battery holder will illuminate if the voltage of the battery falls below a certain level indicating the need for charging There will also be an audible signal There is still enough capacity to perform Page 10 of 20 BM06101 Molift MOVER 300 English 3 5 lift cycles 75 kg 165 Ibs at this point oO If the battery is discharged during a lift it is always enough power to lower the user down again New batteries will not achieve full capaci ty before it has been fully charged and dis charged a couple of times The battery lifetime is about 500 charging cycles O Electronics Electrical emergency lowering There is a counter implemented in the electronic system of the lifter registering the number of lifts This number can be read by using the Molift Serv ice tool and a service lamp indicates when the lift er needs service consisting of exchange of the lift ing motor See the chapter Maintenance The electronic system has a power save function which makes the system sleep after a while with no activity All lights will go out Activate the sys tem by pushing one of the buttons on the hand control If the lifter is run up and down constantly for a longer period the electronics may be overheated and the lifter will stop W
6. Molift MOVER 300 English Page 11 of 20 Minimum internal width molift Labelling The main label is placed on the bottom of the col umn Nominal battery voltage SWL 300 ke 26 4 V DC IP 24 Arca AR Manulai L KA fachuned 2X ps ss NT TIT Etac AS Etac Supply Gjevik Hadelandswaien i N 2816 Gievik Norway 47 4000 1004 Waar TH iit Com For indoors Model name Safe Working Load Read the user manual Part number and year week of pro duction Serial number barcode Manufacturer Type BF Applied Part use Separate waste collection The control label is placed on the right side of the battery holder 12 Month Page 12 of 20 Control lifter accord ing to checklist on page 18 Periodical inspection each 12 month Designated area for calendar and signed label for periodical inspection READ THE USER Accessories Lifting sling Molift Easy Paediatric Sling No head support With head support XXS Part no 3005050 Part no 3006050 Part no 3005000 Part no 3006000 Easy Toilet Sling and Basic Bathing Sling for kids see the tables below size XXS and XS Molift Easy Sling Part no 3025500 S XL L S 0 MANUAL Part no 302340 Part no 3024400 With head support Part no 3047010 M Part no 3074011 L Part no 3047012 BM06101 Molift MOVER 300 English Rev D 08 05 2013 Molift Easy Toilet Sling Part no 3032200 Part no 3033200 Part no 3032300
7. ait until the lifter is cooled down enough for further use Discarded lifters and batteries should be handled as electronic waste and collected separately according to local laws and reg ulations Rev D 08 05 2013 Technical data ae x ER Weight total Ex battery and suspension 36 kg 79 lbs Chassis 19 kg 42 Ibs Lifting column 17 kg 37 Ibs Battery 1 6 kg 3 7 lbs Ml Suspension 3 3 kg 7 3 Ibs Material Steel aluminium and composite plastic Motor K Lifting motor actuator 24 V DC Leg spreading motor 12 V DC Battery Art no 26 4 V NiMH 2 2 Ah ai h 600 ATO Fuse 20 A IN L h Battery charger 1 Mascot type 2215 SR 10 22 cell NiCd NiMH 10 Q Protection B IP24 Number of lifts with fully charged battery 50 lifts 75 kg 165 Ibs up down 50 cm 20 inches Safe Working Load SWL 300 kg 660 Ibs Lifting speed 27 mm sek 1 06 inch sec Sound level max A weighted sound power level L 63 2 dB Operating forces Buttons on hand control 3 4 N Turning diameter 1400 mm 55 1 inches Measurements 1322 x 702 x 1388 mm LxWxH 52 0 x 27 6 x 54 6 inches LxWxH P Maximum intemal with 1065 mm a internal width at maximum reach 9 R 1340 mm B Maximum reach from base C Reach from base with legs spread 180 mm to 700 mm D Baseheignt 115mm Rev D 08 05 2013 BM06101
8. cher 14 Troubleshooting ss 15 Maintenance cccccccscscscscscscscscscsesese 10 IC IO race AA E E een 16 Monthly inspection Erin 16 Periodic inspection esivccttucscinnvecastextinsecdeses 16 DOC eters cin es ea me rs 17 Checklist for periodic inspection 18 CE Declaration 19 Etac AS P molift Etac Supply Gj vik Hadelandsveien 2 2816 Gj vik Rev D 08 05 2013 About Molift Mover 300 Molift Mover 300 is a mobile lifter intended for lift ing and transferring persons to from bed floor chair or similar wheelchair and toilet The lift er is made out of light weight materials has cas tors and is powered by a battery It has electrically adjustable legs and a lifting capacity of as much as 300 kg 660 Ibs It is therefore ideal for insti tutional care settings but can also be used in pri vates homes and nursing homes The lifter should only be used for transfers across short distances such as between a chair and a bed or into bath room rest room and cannot replace a wheelchair or similar The Molift Mover 300 with accessories as de scribed in this manual are CE marked according to the Council Directive concerning medical de vices 93 42 EEC The lifter is classified as medi cal equipment class 1 and tested and verified by a third party according to standards IEC 60601 1 IEC 60601 1 2 and NS EN ISO 10535 2006 Be
9. d and signed The ticked and signed checklist has been passed to the client and a copy sent to your Molift dealer Comments on faults and VEDAS ER nee seed een dem es dione less erecese cer celte EHESS ae nn other ID no if any BN e a a ae eo EEA PEA PAO E E EE EE EEA EETA Inspection carried out by Block Capitals ceeeeeeeeeeees IMO r E Molift certification no if any for inspector repairer aassensssnssnnssnnesn ceeeaeeeeseeeesaeeeeeeeeeeeeesaeeeeeeeseeeesseeeeaeeeeseeesaeeees The equipment has been tested and is in full working order Yes No POS Date Se oi in Page 18 of 20 BM06101 Molift MOVER 300 English Rev D 08 05 2013 molift CE DECLARATION OF CONFORMITY molift y Etac Etac AS Etac Supply Gj vik Hadelandsveien 2 2816 Gj vik NORWAY Telephone 47 4000 1004 hereby declare that Molift PARTNER 255 patient lifter and that the accessoires used only together with this product are in conformity with e The Council Directive concerning medical devices 93 42 EEC and according to this classified as medical equipment class 1 Expiration date 30 May 2017 Molift PARTNER 255 is manufactured in conformity with the following national or international standards that also might implement a harmonised standard e 15010535 2006 Hoists for the transfer of disabled persons Requirements and test methods ISO 14971 2007 Medical equipment Risik ana
10. e are no loose parts on the lifter 3 Check that the emergency button is deactivat ed and that the lifter works 4 Check that you have sufficiently charged bat teries to complete the task you have planned no lights on the battery lamps 5 Check that the service lamp gives a green light indicating it is ready for use If the service lamp gives a yellow or red light the lifter needs serv ice 6 If faults or irregularities are discovered the lift er should be taken out of service Contact your service partner or local Molift representative Battery lamp Service lamp Electrical emergency lowering Battery Molift Mover 300 use lamp The Molift Mover 300 hand control has four but tons two buttons for up and down and two but tons for adjusting the adjustable legs in and out In addition there is a LED battery lamp which illu minates when the battery needs charging Legs in Legs out Down Lifting arm Hand control Drive handle Suspension D 7 Battery Motor actuator f F Battery holder incl control electronics and electrical emer gency lowering Lifting column Legs Emergency stop FRONT direction of driving Chassis BACK Rev D 08 05 2013 BM06101 Molift MOVER 300 English Page 7 of 20 molift Lift and transfer The suspension shall always be positioned across the user as shown left in the illustration below LE Check that the sling is properly fastened to all four ho
11. e emergency lowering procedure again e If it still does not work the suspended user must be lifted out manually either by using the manual lowering function or by requesting as sistance Manually emergency lowering The manually lowering function on the actuator is only to be used when the electrical lowering does not work Manual emer gency lower ing Turn clockwise see arrow on top to lower the lift ing arm carefully until the patient is safely placed in a bed or a chair Page 9 of 20 molift Battery and charger system Battery care and charging Molift Mover 300 is supplied with a battery with a 26 4 V cell unit that is placed in the battery hold er on the lift A battery charger is also supplied to be located easily accessible either stand alone or mounted on the wall Connect the charger mains cable to the wall socket when charging the bat tery The Charger must be placed or installed in a way that makes it easy to disconnect mains ca ble plug Disconnect the charger mains cable plug when the charger is not in use Take care not to damage the cable Charger LED es be Place the battery in the charger After a few sec onds the LED will change from yellow to orange indicating that the battery is charging When the LED gives a constant green light the battery is fully charged The charger LED Light Emitting Diode is indicating the status of the battery as described below Charger LE
12. e to ensure proper logging and written verification performed by authorised service part ner A list of spare parts is avalable on request Rev D 08 05 2013 BM06101 Molift MOVER 300 English Page 17 of 20 Checklist for periodic inspection of Molift Patient Lifters Molift Mover 300 Revision A 05 201 1 COMPULSORY SAFETY CHECK annual BR Whole lifter checked for damage cracks and deformation and found to be in good order Especially suspension lifting arm lifting motor wheels and all cables en Especially column lock column attachment and suspension Accessories have been checked See separate form for sling Battery charger is an accessory P noite o ea cenronave been chakod and aro I working order A a and runs easily and steadily Leg spreading mechanism has been fully extended and Ppp retracted preferably under load and moves evenly and without noise stops in correct positions The lifter has been fully raised and lowered preferably under CR load and moves evenly without noise and the lifting motor shows no runout semicingrequires OoOO RL and the lifter is under 5 years old The lifter has been removed from service and clearly marked OUT OF ORDER BC Certified personnel have been summoned to carry out repairs and servicing Completed Compulsory where lifter has been checked and approved The lifter has passed the safety check and been affixed with the Molift safety check label duly date
13. ery replace battery legs only moves in one direction ine eon nee na Faulty battery charger try an failed contact local representa other charger contact local tive for service and use manu ally emergency lowering where representative for service necessary The lifter moves Short circuit between hand con f you have access to more than one lifter it may uncontrolled trol and lifter clean hand con be helpful to change parts across lifters to help adjustable legs trol plug surfaced with alcohol identify any faults For instance if you suspect the balled en pO ee fault to be inside the hand control exchange the Defective hand control replace hand control with at functional one from another hand control contact local rep similar lifter to see if the problem is fixed resentative for service The control electronics has If you are not able to solve the fault or problems failed contact local representa by yourself using this manual please contact lo tive for service i cal authorised service representative If you do not know whom to contact locally please contact your dealer or Etac Supply Gj vik to get help Rev D 08 05 2013 BM06101 Molift MOVER 300 English Page 15 of 20 molift Maintenance Maintenance of the lifter consists of check be fore use cleaning inspection and service Check the lifter according to the checklist before use on page 7 to reveal faults or errors In regularly in specti
14. fore using the patient lifter See page 5 for mounting description Before using a patient lifter the operator should be trained accordingly Practice lifting a colleague and be lifted by others It is important not only to know how to move another person using the lift er but also how it is to be lifted Try and practice using the relevant slings for the different types of lifts and movement you may encounter Before lifting a person you should explain the procedure When using the lifter it s also important to use the correct sling and accessories according to e type of disability e size e weight e type of movement Ifa fault associated with the operational safe ty and reliability is identified the lifter must be taken out of use immediately and marked Out of order or not put into use at all Rev D 08 05 2013 BM06101 Molift MOVER 300 English molift Explanation of symbols This symbol is used to point out instructions and information related to workplace safety where injury may occur if the information is disregarded or ignored Follow these instruc tions be careful and attentive at all times This symbol indicates important and useful information If taken into consideration it will help the operator of the lifter to work efficiently It may help simplify routines and to explain complicated facts O Fo Page 3 of 20 molift General safety precautions General Before putting a Mol
15. ift Mover 300 into operation the operator must ensure that the lifter and acces sories are in good working order especially with regards to safety A Molift Mover 300 shall only be used when all safety devices and equipment is in place and fully operational The lifter must be taken out of service immediate ly or not returned to service if faults and or irreg ularities that may have influence on the safety are discovered O Injury to personnel or equipment may occur if Molift Mover 300 is used in an incorrect manner and if i e e covers are removed by unauthorised personnel e used incorrectly e insufficient maintenance e load exceeds maximum limit The maximum load stated in this manual and on the lifter is the maximum load e unauthorised repair of electrical devices or ca bles The lifter has an expected lifetime of 10 years or 30 000 lifts with max load SWL when all recommended service is performed Lift and transfer The Molift Mover 300 has a Safe Working A Load of 300 kg 660 Ibs meaning that it is tested and approved for lifting of patients up to 300 kg 660 Ibs Attempts to lift patients above SWL may damage the lifter and lead to personal injury The patient lifter may tip over if used incor rectly Ignorance of warnings and instruc tions may lead to personnel injury Read in structions carefully before attempting to lift anyone A Page 4 of 20 BM06101 Molift MOVER 300 English Pay clo
16. l regulations Use the checklist for periodic inspection on page 18 Inspection is to be performed by authorized per sonnel The owner is responsible to ensure prop er logging and written verification of each inspec tion Rev D 08 05 2013 molift by Etac Service Molift Mover 300 has a LED on the battery holder indicating if the lifter needs service The LED gives a green light when the lifter is ready for use Battery lamp Service lamp Electrical emer gency lowering The electronics logs how much the lifter is being used and the load it is used with After a given time of usage there will be given a signal that the lifter needs service to the service LED The LED will first give a yellow light then red Take contact with your local service representative and order serv ice If there is a sound together with the light it means the lifter needs service immediately Service lamp status No Tigh Ready for use Yellow Order service lifter still works Red Perform service Red sound Perform service imme diately Service consists of replacing the lifting motor and check replacement of worn or damaged parts Service and repair shall be performed only by an authorised service representative according to procedures in the technical manual The service partner uses the Molift Service Tool to read the data from the lifter and for logging serv ice and resetting the service LED The owner is re sponsibl
17. lysis Notified body Danish Technological Institute Wood Technology NEMKO AS Gregersensvej 3 Gaustadalleen 30 DK 2630 Taastrup N 0314 OSLO Denmark Norway Tel 45 7220 2301 Tel 47 2296 0342 Title Site Manager Name Knut Martin Frosaker Company Etac AS Etac Supply Gj vik lt 30 05 2012 a i Date Signature Rev D 08 05 2013 BM06101 Molift MOVER 300 English Page 19 of 20 Find your distributor visit Molift com molift
18. mol MOVER 300 re CE molift Rev D 08 05 2013 BM06101 Molift MOVER 300 English ol ci cr c ja ez a label fois en molift Table of content About Molift Mover 300 3 Before using the patient lifter 3 Explanation OF symbols 2 3 General safety precaution 4 E E EI EEA 4 Lift and transfer 4 Assembly and disassembly 5 CHACHA Siar cse sacra EER E 5 ASSEMDI Yose sn irun Eein E 5 DisasSsemDIy ecrire nS 6 SOIO oa E ena EE E E eA 6 Checklist before use cccccescscscsccceces 7 Molift Mover 300 USC cccccccccccscsceee 7 Lift and transfer ccccccccccccscscscscccccesed Use Of spread legs 8 Using USINE cntectonceteereccennaes 8 Safety devices desde octo EEEE EE Emergency stop and lowering 9 Battery and charger system 10 Battery care and charging 10 Battery capacity 10 FISCO S eroaren da ane ces 10 Technical data 11 Labelling sssrini 12 Accessories 00000000000000000000000000000000000000000 1 2 L O SO a ei 12 Page 2 of 20 BM06101 Molift MOVER 300 English Equipment ssccscccccccccscccscescessecseessese 14 Quick release SUSPENSIONS 14 Castor with directional lock 14 Integrated charger 14 Suspension with scale 14 Molift Stret
19. nged according to descrip tion in Technical Manual by authorized personnel This castor has no brake therefore we recom mend to change only one of the castors Push the red handle down to lock the direction Release by pulling the handle up Integrated charger e Part no 1340101 The charger can be mounted on the lifter perma nently Park the lifter and connect to a wall socket to charge the battery Page 14 of 20 BM06101 Molift MOVER 300 English Suspension with scale e Scale with 4 point steel suspension Large Part no 1431001 e Scale with 4 point steel suspension Medium Part no 1431002 Ds Read the user manual that comes with the Scale before use Change to suspension with scale with quick re lease as you change to any other suspension Molift Stretcher e Molift Stretcher excl loops Part no 2150103 Standard set of lifting loops Part no 2150357 Set of auto strap collector Part no 2150356 Set of Safety belt Part no 2150355 Te oa 14 s i i i 11 n 5 r J f The Molift stretcher can be used in combina tion with all Molift 4 point suspensions on Molift Partner 205 e Molift Stretcher MR compatible Part no 2150108 Only available with Standard set of lifting loops Part no 2150357 Read the operating manual that comes to gether with the stretcher before use Rev D 08 05 2013 O molift Troubleshootin g Symptom Possible cause ac
20. ngs The Molift lifting slings are easy to use Please see the user manual that comes with the sling for spe cific instructions It is recommended to use Molift Easy slings Slings from other manufacturers may have other specifications leading to unexpected instability and possible injury to personnel Torn cut frayed or broken slings can fail re sulting in serious injury to the user Use slings in good condition only Destroy and discard old unusable slings Molift Easy sling E zi s L AIR Ea j i a i tT Ee a i h r Fold the sling as indicated above before use The grey side should be facing away from the user when putting the sling in place The sling should be held by one hand leaving the other free to move and support the user Rev D 08 05 2013 Safety devices Molift Mover 300 is equipped with several safety devices which are intended to prevent damage to personnel and equipment in the case of incorrect use e The lifter has an overload sensor preventing the lifter to be operated with more than safe working load 300 kg 660 Ibs If the load ex ceeds the SWL the lifter will stop the move ment e The lifting arm is hinged to prevent the arm and suspension from squeezing the patient if it is lowered too much The actuator will not pro duce any force when moving downwards e The suspension has safety hooks to prevent the sling loops to fall off e The electronics are disabled if
21. oks on the suspension to make sure the patient is nor sliding or falling out Try to position the user as low as possible prefer ably resting the feet on the chassis when transfer ring the lifter with a suspended user In this way the centre of gravity will be as low as possible and therefore reducing the risk of instability The lifter should be manoeuvred with spread legs in outer position to achieve the highest possible stability Be careful during movement the suspended user may swing somewhat during turns stops and starts Be particularly careful when manoeuvring close to furniture to prevent the suspended user from colliding with these objects The lifter shall not be used to lift or move us ers on sloping surfaces Avoid deep pile carpets high thresholds uneven surfaces or other obstacles that may block the cas tors The lifter may become unstable if forced over such obstacles increasing the risk of tipping over O Use of spread legs Use wide legs wherever appropriate for instance to position the lifter around wheelchairs toilets etc The leg spreading mechanism has a safety function preventing it from squeezing with high force This may lead the motor to stop if changing direction quickly Push another button to start again Page 8 of 20 The lifter shall only be used for movement over short distances It is not a replacement for wheelchair or similar BM06101 Molift MOVER 300 English Using lifting sli
22. ons of the lifter which as a minimum should be monthly inspections and annual periodic in spections Cleaning O Detergents must be pH neutral Do not use solvents or strong liquids this may dam age surfaces on the lifter For disinfection when needed use isopropyl alcohol Avoid abrasive cleaning products e Clean surfaces with a damp cloth using an ap propriate detergent e Remove hair and pile from the castors and ver ify that the castors rotates without abnormal friction e Clean contact and hand control with spirit or similar to remove grease and dirt e Regular cleaning is recommended and should be implemented in the suitable cleaning rou tines Page 16 of 20 BM06101 Molift MOVER 300 English Monthly inspection Assemble the lifter before inspection e Check the lifter according to the checklist be fore use on page 7 e Clean the lifter as described above e Verify that the contacts of the hand control and charger is firmly in place and verify that the ca bles for the hand control actuator and charger are intact e Run the lifter up and down to verify that it runs normally and without any abnormal noise The lifter must be taken out of service imme diately and marked Out of order or not taken into service if faults and or irregularities are discovered Periodic inspection Etac Supply Gj vik recommends periodic inspec tion once a year alternatively more often if re quired by loca
23. se attention to your actions Ensure that all four loops of the sling are securely fas tened to avoid the user slipping or falling Use the push handle to manoeuvre the lift do not attempt to manoeuvre the lift by pushing on the lifting arm actuator or arm Torn cut frayed or broken slings can fail re sulting in serious injury to the user Use slings in good condition only Destroy and discard old unusable slings Molift slings shall only be used to lift persons Never use sling to lift and or move objects of any kind Molift Mover 300 should not be run con stantly for more than 2 minutes with maxi mum load and rest for minimum 18 min utes If the lifting movement does not start when the corresponding button is pressed please consult the fault finding table in the maintenance chapter to locate the fault 2 F amp F Be PF Several factors have to be considered during movement of the lifter Stand to the side of the lift er when lifting Ensure that arms and legs are clear of the lift chair bed etc try to maintain eye con tact with the user this will help the user feel safe and comfortable Medical electrical equipment requires spe cial precautions regarding electromagnet ic compatibility EMC Portable or mobile radio communication equipment may af fect the medical electrical equipment and should be kept minimum 25 cm 10 inches from the lifters electronics O Rev D 08 05 2013 Unpacking
24. tion Faults on lifters that do not function as they should The lifting arm Emergency stop button is acti after assembly page 5 or after the check before does not move valea mn a pi use has been completed page 8 can be localized gency stop see p 9 using the troubleshooting table below Battery is empty change to new battery or recharge battery Symptom Possible cause action see page 10 The lifting column The lifting column is not cor The control electronics of the is wobbly rectly positioned in the chassis lifter is overheated Leave lifter or the locking handle is not fully to cool down see page 10 locked verify position of lift ing column and locking handle acc to mounting instructions on page 5 The lifter is overloaded make sure the load does not exceed 300 kg see page 9 The hand control cable is un The lifter moves The castors move unevenly be plugged reconnect plug unevenly on a cause of pile and dust clean plane surface castors as described on page 16 Hand control has failed re place hand control contact lo Fault in the leg spreading cal representative for service mechanism contact local rep Defective control electronics resentative for service contact local representative for The lifter only Hand control has failed test service a a w angi er anG ONDAN Battery does not Faulty battery try another bat rection adjustable change if defective recharge t
Download Pdf Manuals
Related Search