User Manual - American Weigh Scales
Contents
1. AWS Aercan Weigh Scales Inc BLADE Series p BLADE 50 eLape 700 User Manual BLADE 600 BLADE 1000 Blade Manual Thank you for purchasing the American Weigh Blade Series digital pocket scale Please read all operating instructions carefully before use Scales are precision instruments and should always be handled with proper care To ensure years of reliable service keep these simple tips in mind Do not exceed the scales maximum capacity Overloading your scale can permanently damage it e Avoid exposure to extreme heat or cold Scales perform best at normal room temperature If temperatures have changed dramatically recalibration may be necessary Allow your scale to warm up for 30 60 seconds before performing calibration if available e Store your scale in a clean dry location Dust dirt and moisture can accumulate on the weighing sensors and electronics causing innacuracy or malfunction e Avoid using your scale in close proximity to strong radio wave emitting devices such as computers cash registers and cordless phones e Always weigh on a flat and level surface free from vibrations and drafts The corner of a room is usually the most stable Gently apply all items to be weighed Do not drop items onto the weighing platform e Avoid dropping your scale The warranty does not cover damage due to rough treatment or overload I OPERATION Place Scale2. on a horizontal flat surface 1 Press ON OFF key 2 Wait until 0 0 is displayed 3 Put the object s on the weighing platform 4 Using the MODE key you can switch between the weighing units Il TARE WEIGHING 1 Turn on scale as described above 2 Place the tare item on the platform 3 Press TARE and wait until 0 0 is displayed 4 Add the net weight item Ill CALIBRATION Calibration is NOT required before first use Only calibrate if scale is not weighing properly Make sure you use the correct calibration weight for your scale or the calibration will not be accurate BLADE 50 50g calibration weight BLADE 100 100g calibration weight BLADE 600 500g calibration weight BLADE 1000 1000g calibration weight 1 Turn ON the scale 2 Press and hold the MODE key until CAL is dis played Release the MODE key 3 Press MODE again Now the display will read CAL and the required calibration weight will flash 3 times 4 Place the required calibration weight for your scale on the center of platform Wait 3 4 seconds The LCD will display PASS 5 Remove the weight and press ON OFF to turn off the scale Finished Repeat if necessary IV BLADE1000 Calibration Procedures You will need a 1000g 1kg calibration weight 1 Turn on the scale by pressing ON OFF key 2 Wait until the LCD displays 0 0 then press and HOLD the MODE key for 3 seconds The LCD will
3. 0 2gn minimum Weighing Units g Oz ozt dwt g oz ct gn Calibration Weight not Included 500g 1000g 50g 100g Platform Dimensions inches 2 75 x 2 75 Stainless Steel Scale Dimensions inches 3 75 x 3 75 x 0 75 Power 2 x AAA Batteries included
4. display CAL You can now release the MODE key 3 Press MODE key again the LCD will display CAL and 1000 0 4 Add 1000g calibration weight the display will show PASS and return to normal weighing mode 5 Put away the calibration weight and press ON OFF to turn off the scale Finished Repeat if necessary V TROUBLESHOOTING The primary reasons for inaccuracy or malfunction are low batteries incorrect calibration overload or operating on an unstable surface Please keep this in mind and maintain and operate your scale properly This scale is a precise instrument and must be handled with the utmost care and caution Display Elimination of errors Nothing Battery Symbol lo or 88888 Change the batteries OUE2 Recalibrate the scale as shown above EEEEE You are overloading the scale Remove the excessive load immediately LLLLL The delicate weighing load cells have been damaged by misusing the scale i e it was shocked dropped or overloaded You can try recalibrating the scale If the load cell has not been damaged too much it will work again after recalibration UNST Use the scale in a more stable position Specifications Model Blade 600 Blade 1000 Blade 50 Blade 100 Capacity 600g 1000g 50g 100g 21 160z 35 270z 1 7640z 3 5280z 19 290zt 32 150zt 250ct 500ct 385 8dwt 643 0dwt 771 5gn 1543gn Resolution 0 1g 0 01g 0 010z 0 0010z 0 010zt 0 05ct 0 1dwt 0 1gn
Download Pdf Manuals
Related Search