Home

8and 16 channel dvr manual

1. button After press MODE button press t UP button to select display mode Under menu operation and PTZ control it is Upward key 5 DOWN button After press MODE button press P DOWN button to select display mode Under menu operation and PTZ control it is Downward key 6 PLEFT button After press MODE button press lt LEFT button to select display mode Under menu operation and PTZ control it is Leftward key 7 P RIGHT button After press MODE button press RIGHT button to select display mode Under menu operation and PTZ control it is Rightward key 8 CANCEL button In menu or PTZ operation mode press this button to quit menu or PTZ operation mode In playback mode press this button to stop playback 9 Channel button Full screen display one selected channel by pressing numeral button 10 MODE button Repeat pressing this button to display image in different modes PIP1 PIP2 PIP3 four pictures nine eight pictures In PTZ operation mode press MODE button to enter focus control then adjusted by lt button and button Press it again to quit focus control 11 AUTO button In display mode press this button to enter auto switch for single channel The user can set the switching time The DVR can display each channel in turn for this time Press again to quit from auto switch
2. buttons to move cursor to a new grid press ENTER button to set up the new area The detection area display in different color Press MENU button and select EXIT to quit 4 Choose CLEAR to clear the detection area operation is same with 3 5 Press MENU button and select EXIT to quit Mouse 1 Left click the SET on the right of MOTION AREA to detection area 2 Right click the mouse and display SELECT CLEAR and EXIT 3 Choose SELECT to set up detection area keep left click and drag to choose the detection area The detection area display in different color Right click the mouse and choose EXIT to quit 4 Choose CLEAR to clear the detection area operation is same with 3 5 POST RECORD TIME 1 Set up the time after the alarm happened the maximum time is 60 seconds The default time is 5 seconds 2 Can only used in MOTION record mode 6 BUZZER TIME The buzzer ring when detecting the motion the maximum ring time is 60 seconds 7 ALARM TIME Control the time of outside alarm devices when detecting the motion the maximum time is 60 seconds 8 MOTION TRACE When the MOTION TRACE is on the area color around the moving object is red during motion alarm 3 5 SENSOR Move the cursor to SENSOR icon and press ENTER button to enter the SENSOR sub menu 5 SENSOR SENSOR CHAIN NED A SENSOR TYPE NORMAL OPEN POST RECORD TIME SI LSE C BUZZER TIME SEC 5 ALARM TIME SEC
3. 2 When choosing TIME SEARCH to playback the middle button of mouse can be used to change time 3 Click the STOP icon on the bottom playback status bar to stop playback EVENT INFO EIMIEIRIGIEF EMERGE EMERGENC EMERGE EMERGE EMERGE EMERGE EMERGE EMERGENCY EMERGENCY 2 9 Record Event Group Search Front panel ooc oc occ Oo Oto D ara am t4 2 2 2 2 2 2 2 2 2 NRHN HW HW A fO DID oooco oc o olo eo 4 4 Nu uu colo LE M N N HN NN oic SNS NS OS o x r Gaqgca Ln s E P A LJ NEE N OG c ooo 1 Press SEARCH button to enter SEARCH MENU 2 Press LEFT or RIGHT button to choose EVENT SEARCH mode 3 Press UP or DOWN button to choose date and time and then press ENTER button to play back 4 Press CANCEL button to quit the menu Mouse 1 Click the MENU on the left of the bottom status bar choose SEARCH again to enter SEARCH MENU then double click EVENT SEARCH to play back 2 Click the STOP button on the bottom playback status bar to stop playback 2 10 Emergency Search Front panel EMERGENCY SEARCH RECORD TIME 9 J tA 74 109 O ceoococco 200000 ofo oo ola NAN m M Om M ON DD L2 8 4 44 4 4 47 NUM Iu P um mico JEN a N63 Oo OLO 7 7 7 7 7 7 7 4 7 ooocoo o 1 Press SEARCH button on the front panel to enter SEARCH MENU 2 Press LEFT
4. Connect USB device with the latest firmware and press ENTER to upgrade firmware bus WARNING FIRMWARE UPGRADE MAY MA KE THE SYSTEM FATAL ERR OR CONTINUE Note After connecting the USB device it needs to wait for ten seconds then upgrade firmware 9 FACTORY RESET If DVR in disorder sometimes it needs to reset again to factory default setting as following WARNING SYSTEM SETUP WIiILt INIT I ALIZE CONTINUE Press ENTER button to reset to factory default setting or press CANCEL to quit 10 LANGUAGE Press LEFT or RIGHT button to select menu language include Chinese English Korean and Japanese Other languages can be built in if need 11 Slave monitor setup Setup the channel switch time of the slave monitor Move the cursor to slave monitor then press ENTER button the sub menu is as below Press UP DOWN button to move cursor prss menu to select channel display on slave monitor Channel open select channels display on slave monitor Switch time setup the channel switch time on slave monitor Event log setup open or close the event record of switch of display IV Default Setting The Default setting for the DVR by the manufacturer is as following User can change the setting according to the requirements When recovering to default setting you can choose FACTORY RESET in SYSTEM SET sub menu and reset all setting to default factory
5. In playback mode repeat press AUTO button to rewind frame by frame prss ENTER to quit and back to normal playback In PTZ operation mode press AUTO to control the PTZ auto rotation press again to stop auto rotation of PTZ 12 MUTE button In display mode press MUTE button to turn on and turn off the audio In PTZ operation mode press MUTE button to enter iris control then adjusted by button and button Press it again to quit iris control 13 BACKUP button In display mode if there is USB CD burner to connect the DVR press the button to backup the information Choose the start time and the end time of the backup and press ENTER button to backup When backup is completed the system automatically quit from the menu If there isn t backup device to connect to the DVR the DVR reminds can t find the backup device and press CANCEL button to quit from the menu 14 PTZ button In single channel display or record mode press this button to enter PTZ operation press this button and button to adjust zoom ratio of camera press PTZ button again to quit zoom ratio adjustment press CANCEL button to quit from PTZ operation In playback mode press this button to forward display frame by frame press enter return to normal playback speed 15 REC button When setting DVR record mode to OFF in the menu press the REC button to
6. 2 Keep left click and drag to set schedule time 3 Left click the small circle on the top right to save and quit the menu Left click CANCEL icon to quit the menu without save 3 7 NETWORK Move the cursor to NETWORK icon and press ENTER button to enter the NETWORK sub menu l NETWORK MODE TMASK GATEWAY NAME SE DONS RVE 1 IP MODE Choose the LAN IP mode include static IP and dynamic IP Press LEFT and RIGHT button to choose IP mode The default mode is static IP 2 PORT Set the server port of network Press LEFT and RIGHT button to set the port The default is 3100 3 IP Set the LAN IP address of the DVR Press ENTER button to enter the IP setup keyboard box la I4 ul KEYBOARD INSERT 1 2 Front panel D Press UP DOWN LEFT RIGHT button to select the letters of keyboard box Press ENTER button to input the letters Move the cursor to the symbol of keyboard box and press ENTER button to delete the chosen letters 2 Move the cursor to ENTER of keyboard box and press ENTER button to save and quit menu 3 Press CANCEL button to quit from menu without save Mouse 1 Move the cursor to IP MODE in NETWORK sub menu Left click the SET icon on the right to enter IP mode keyboard box 2 Click the letters and click ENTER to save and quit Right click to quit the menu without sav
7. backup the information Note If no backup device the DVR will display warning box when backup WARNING BACKUP UND 3 9 SYSTEM Move the cursor to SYSTEM icon and press ENTER button to enter the SYSTEM sub menu SYSTEM 4 r ease T ME SETUP SYSTEM PASSWORD Sd vsTEM INFO Bands VIDEO FORMAT LOG VIEW LOG SET FIRMWARE UPGRADE jF ACILORY RESET LANGUAGE ae M d 1 TIMESETUP Press ENTER button to set up the time as following TIME SET TIME 2ooOm wer FORMAT ASIA TIME Setting the DVR system date and time FORMAT The date and time display types ASIA EURO and US Front panel 1 Press LEFT or RIGHT button to move the cursor Press UP or DOWN button to set up the date and time 2 Press ENTER button to save and quit 3 Press CANCEL button to quit the menu without save Mouse 1 Choose TIME SETUP in the SYSTEM sub menu and left click the SET on the right to enter TIME SET sub menu 2 Move the cursor to choose items and move the middle wheel of the mouse to set up the date and time 3 Press the circle on the top right to save and quit 4 Press the CANCEL icon to quit the menu without save 3 SYSTEM PASSWORD Move the cursor to choose the SYSTEM PASSWORD and press ENTER button to enter SYSTEM PASSWORD sub menu as following PASSWORD CONFIRM PASSWORD The menu password CONFIRM Repeat and confir
8. mode is schedule record The default is SCHEDULE 1 3 4 MOTION Move the cursor to MOTION icon and press ENTER button to enter the MOTION sub menu SU MOTION CAMERA CHANNE ENABLE T V 3S AREA CORDO TIME TIME If enter TIME SETTING sub menu during recording the DVR will stop recording automatically 1 CAMERA CHANNEL press LEFT or RIGHT button to choose the channels for motion detection 2 MOTION ENABLE Turn on or turn off motion detection 3 SENSITIVITY Setting the sensitivity for motion detection as following Mew 1 Set M T LS SENSITIVITY Ub SENSITIVITY A mee SPATIAL ANE te 77 BLACK LEVEL que WHITE LEVEL 1 SENSITIVITY Setting Sensitivity 2 SPATIAL Setting the area for motion detection 3 BLACK LEVEL Black level sensitivity 4 WHITE LEVEL White level sensitivity If turn off the sensitivity or setting low sensitivity can affect motion detection function Setting sensitivity according to your requirement MOTION AREA Setting the detection area for the channel as following Front panel 1 Detection area cover with small green grids 2 Press MENU button to display the setup items SELECT CLEAR EXIT 3 Choose SELECT to set up detection area press UP DOWN LEFT and RIGHT buttons to move the cursor and set up the area press the ENTER button to confirm the area then press UP DOWN LEFT and RIGHT
9. or RIGHT button to choose EMERGENCY SEARCH mode 3 Press UP or DOWN button to choose date and time and then press ENTER button to play back 4 Press CANCEL button to quit from EMERGENCY MENU Mouse 1 Click MENU on the left of the bottom status bar choose SEARCH to enter SEARCH MENU then double click EMERGENCY SEARCH to play back 2 Click the STOP on the bottom playback status bar to stop playback 2 10 USB Backup Front panel 1 Insert the USB device to DVR USB port after 10 seconds press BACKUP button to enter BACKUP MENU 2 Press LEFT or RIGHT button to move the cursor and press UP or DOWN to set up the start time of backup and the end time of backup 3 Choose the backup format to AVI format DVR default format press ENTER button to start backup 4 Press CANCEL button to quit from BACKUP MENU Note The USB device must be removed after backup finished Mouse 1 Click the MENU on the left of the bottom status bar then click SYSTEM SETUP to enter the SYSTEM MENU 2 Choose BACKUP to enter BACKUP MENU click the SETUP to set up the parameters 3 Click the small circle symbol on the top right to confirm backup condition 2 12 CD ROM Backup Optional function 1 Before using the CD ROM to backup please install the CD ROM burners 2 Put in the blank CD to CD ROM and pres
10. playing Note Before playback need to log in by password first When playback finished need to log in by password again 2 FilePlay Open and play backup files from viewer or from DVR copies Speed 0 20 6 s Open From To Ji P12 p Open Click to open backup file then click the PLAY button to play it g Skee Start v Rec Stop 3 Click to start DVR recording click to stop DVR recording oO DW CS kee Start During recording will change to red color If click the recorded files will be saved in DVR s HDD notin PC s HDD Note Setting the record mode to Emergency Record before using this operation VI Parameters Table Item Specification Compression Format H 264 Video System NTSC PAL Video Input Video 1 0Vp p 75 Q BNCX8 BNCX 16 Video Output 1CH Compound Video Output 1 0Vp p 752 BNCXIS video 1CH VGA Output Frequency 60 Hz Resolution 1024 x 768 Resolution Display NTSC 720x480 PAL 720 X 576 Audio Input 8Db22k Q RCA connectorX4 Audio Output 8Db3k Q RCA connector X 1 Alarm Input 4 Alarm Output 1 Frame and Resolution CIF NTSC 240fps 352x240 1 2D1 NTSC 120fps 720x240 PAL 100fps 720x240 D1 NISC 60fps 720x480 PAL 50fps 720x576 PAL 200fps 352x288 Occupation Space All 16channels record at high quality mode 1 4GB H HDD Port SATA hard disk Network Port 10M 100M Ethernet
11. 1 SENSOR CHANNEL Press LEFT or RIGHT button to choose the sensor channel ALL is to choose all channels 2 SENSOR TYPE NORMAL OPEN Open the sensor NORMAL CLOSE Close the sensor 3 POST RECORD TIME 1 Setup the time after the sensor alarm happened the maximum time is 60 seconds The default time is 5 seconds 2 Canonly used in SENSOR record mode 4 BUZZER TIME The buzzer ring when detecting the sensor alarm the maximum ring time is 60 seconds 5 ALARM TIME Control the time of outside alarm devices when detecting the motion the maximum time is 60 seconds 3 6 SCHEDULE Move the cursor to SCHEDULE icon and press ENTER button to enter the SCHEDULE sub menu nad Na T 3 4 ub x wu g n AV Oo SCHEDULE CUP i 4 x m 0 2 4 6 8 10 12 14 16 18 20 22 24 El If enter TIME SETTING sub menu during recording the DVR will stop recording automatically Front panel 1 Press MUTE button to choose ALWAYS record mode Press AUTO button to choose MOTION record mode Press BACKUP button to choose SENSOR record mode Press MODE button to close schedule record mode 2 Press UP DOWN LEFT and RIGHT buttons to move the cursor Press MENU button to set schedule include time 24 hours and day one week There are 5 groups of schedule time can be set 3 Press ENTER button to quit Mouse 1 Left click to choose SCHEDULE mode
12. DVR 8 16CH Stand alone digital video recorder User s Manual 8 16CHANNEL H 264 DVR Warnings Safety This device is an INDOOR equipment and NOT water resistant In order to avoid dangers of short circuit or electric shock do NOT expose it in rainy or moist environment In case of any solid or liquid matter get into the device case turn off the power immediately and ask for qualified technicians to check it before restart Q This device is a precise equipment ask qualified technicians or distributors for help if any malfunction Do NOT attempt to repair any unit of it by yourself Power Supply The digital video recorder applies DC12V 5A power adaptor The voltage of the power must be verified before use When this machine is not using for a long time pull plug of power adaptor Using Place Do NOT put this device near by a radiator or heat ventilator Do not expose to sunlight or dust Keep away from magnetic force or vibration Avoid humidity or water Most important connect this device to the ground to avoid electric shock Notice Any re construction or change maybe leads to destroy of this machine which brings many inconveniences to user Therefore do not disassemble or modify this unit Otherwise the dealer will not be responsible for it The damages caused by following incorrect operation do not belong the range of the warranty even if it is within the warranty period OUsing incorrect p
13. IME SETUP 2 SYSTEM PASSWORD 3 SYSTEM INFO 4 VIDEO FORMAT 5 LOG VIEW 6 LOG SET 7 DISK FORMAT 8 FIRMWARE UPGRADE 9 FACTORY RESET 10 LANGUAGE 11 Slave monitor display IV Default Setup V PC Viewer Operation VI Parameters Table I System Installation 1 1 Accessories Open package the accessories should include 1 User s manual 1pcs 2 DC12V 5A power adaptor 1pcs 3 Screws 1 set 4 CD with PC software 1pcs 5 Infrared remote controller 1pcs 6 USB port mouse 1pcs 1 2 Introduction of the front panel Function of the front panel 8CH 1 MENU button Press this button to enter main menu press CANCEL button to quit menu After setting parameters in menu press MENU button to save and quit menu 2 POWER button In display mode long press the button for more than 2 seconds and DVR will display power on off dialog box press CANCEL button to give up turning off DVR and return back to display mode Press ENTER button to turn off DVR If DVR turned off by POWER button can press POWER button again to turn on DVR 3 ENTER button In display mode press this button to enter popup menu press UP or DOWN button to move the cursor Re pres ENTER button to enter sub menu Press CANCEL button to quit menu When playback ENTER button is a pause button In PTZ operation mode press ENTER button to enter pre set position function 4 t PUP
14. ORD icon and press ENTER to enter the RECORD sub menu 22 RECORD CHA NINE RESOLUTION PRE RECORD OFF FPS 25 00 QUALITY HIGH RECORD MODE OFF AUDIO OFF SCHEDULE SCHEDULE If enter RECORD sub menu during recording the DVR will stop recording automatically 1 CHANNEL Choose the channel for recording Al is to choose all channels 2 RESOLUTION The DVR supports D1 1 2D1 CIF recording D1 6 25 fps for each channel 1 2D1 12 5 fps for each channel CIF 25 fps for each channel real time Different resolution has different image quality D1 is the best 3 PRE RECORD When PRE RECORD is on and the recording mode is alarm record motion detection mode sensor mode the DVR can record ahead 2 seconds before the alarm happened This ensures the alarm event is complete 4 FPS The DVR can set frame rate for each channel and set to real time recording PAL 25fps NTSC 30fps Note Under CIF resolution the frame rate is maxmum real time 5 QUALITY The image quality can be set HIGHEST HIGH STANDARD LOW 6 RECORD MODE 1 The record mode can be set ALWAYS MOTION SENSOR SCHEDULE OFF 2 When setting OFF the DVR can start emergency record manual record 7 AUDIO 1 Turnon or turn off audio record It can record 4 channels audio 2 The DVR can record the 4 channels audio when selecting ALL If record only one channel s audio don t choose ALL 8 SCHEDULE Choose the DVR schedule list if the record
15. SEARCH or EVENT SEARCH mode then press ENTER to play back 4 SEARCH 2008 09 SUN MON TUE WEO THU FRI SAT 3 4 5 LM m an owe on N so N a LM NE own NN oue lif 1 during playback press ENTER button to pause and press ENTER again to continue 2 During playback press REWIND or FAST FORWARD button to check the recorded information by the speed of X2 or X4 or X6 3 Press CANCEL to stop playing Shuttle switch During playback use the outer ring of this switch to rewind or fast forward Use the inner ring to playback with single frame Mouse Click the MENU on the left of the bottom status bar and choose SEARCH to enter SEARCH MENU and the user can double click to choose playback mode to play back 2 8 Record Time Search Front panel TIME SEARCH Press SEARCH button to enter SEARCH MENU 2 Press LEFT or RIGHT button to choose TIME SEARCH mode 3 Press LEFT or RIGHT button to choose date and time and press UP or DOWN button to change the date and time press ENTER button to play back 4 Press CANCEL button to quit from TIME SEARCH MENU Mouse 1 Click the MENU on the left of the bottom status bar and then choose SEARCH to enter playback SEARCH MENU then double click to choose TIME SEARCH mode to play back
16. apacity of the second master hard disk 5 SEC SLAVE The size and capacity of the second slave hard disk Note This type of DVR only support one hard disk 6 HDD OVERWRITE a When setting to ON the DVR system will automatically delete and cover the first group information of hard disk and no stop recording if the hard disk full recorded b When setting to OFF the DVR system will stop recording if the hard disk full recorded 5 VIDEO FORMAT The DVR can set to PAL or NTSC system 6 LOG VIEW The DVR can record the time of event if log is enabled 7 LOGSET Move cursor to LOG SET in SYSTEM sub menu and press ENTER button to enter LOG SET sub menu as following E UE AN LOG SET MOTION SENSOR MANUAL BOOTING lt MOTION Setting to ON to save motion alarm event in the log SENSOR Setting to ON to save sensor alarm event in the log MANUAL Setting to ON to save manual recording event in the log BOOTING Setting to ON to save DVR switch on and switch off event in the log 8 DISK FORMAT Move the cursor to choose the DISK FORMAT and press ENTER button to enter SELECT DISK sub menu as following x tbe sELECT DISK FIRST REC TIME LAST REC TIME Press LEFT or RIGHT button to choose the hard disk for format ALL is to format all hard disk Press ENTER button to format hard disk Press CANCEL button to exit hard disk format 9 FIRMWARE UPGRADE
17. ard box and press ENTER button to delete the chosen letters 2 Move the cursor to ENTER of keyboard box and press ENTER button to quit from the menu 3 Press MENU button to save and quit from menu 4 Press CANCEL button to quit from menu without save Mouse 1 2 3 4 Enter the CAMERA sub menu move the cursor to Title and left click the SET to enter keyboard box Click the letters by using mouse to set title click ENTER to quit from SET menu or right click the mouse to quit from the menu Press SAVE to save and quit from the menu Press EXIT to quit from the menu without save 4 PTZ PROTOCOL 1 The DVR can support PELCO D and PELCO P When setting it to OFF in the menu can close PTZ function 2 The default baud rate 2400bps for PELCO D 9600bps for PELCO P 5 PTZ ADDRESS The default address for PTZ control as following Channel Address Channel 1 Channe2 2 Channe3 3 Channe4 4 Channe5 5 Channe6 6 Channe7 7 Channe8 8 Channe9 9 Channel 0 10 Channel 1 11 Channel 2 12 Channel 3 13 Channel 4 14 Channel 5 15 Channel 6 16 6 EVENT POPUP Turn on or turn off event record The DVR can record the event time and the event can be recorded and saved in the event list 7 MAIN ROT TIME Setting the switch time for displaying each channel in turn 3 3 RECORD Move the cursor to REC
18. ast forward Use the inner ring to playback with single frame 26 Mouse port Connection with USB mouse 27 USB port Connection with USB disk for updating firmware and backup files Can not use USB mouse to this port 28 CD RW mount For mounting CD RW driver remove the front pannel when install CD RW driver 1 3 The rear panel 8CH rear panel 1 Video inputs CH1 CH8 2 Slave video output 3 Master video output 4 Audio inputs CH1 CH4 5 Audio output 6 VGA output optional 7 RJ 45 Ethernet 8 RS 485 PTZ 9 DV12V 5A power input 10 The alarm sensor inputs 10 Grond 16CH rear panel 1 Video inputs CH1 CH16 2 Slave video output 3 Master video output 4 Audio inputs CH1 CH4 5 Audio output 6 VGA output optional 7 RJ 45 Ethernet 8 RS 485 PTZ 9 DV12V 5A power input 10 The alarm sensor inputs 10 Grond 1 4 The connection of rear panel SCH and 16CH are the same CAMERA CAMERAS 9O E CAMERA CAMERAS The alarm sensor inputs 2221 2019 18 17 1615141312 1110 9 8 7 6 54 32 1 0000000000000000000000 From right to left No 1 1 IR alarm signal input No 2 2 Infrared alarm signal input No 3 3 Infrared alarm signal input No 4 4 Infrared alarm signal input No 5 5 Infrared alarm signal input No 6 6 Infrared alarm signal input No 7 7 Infrared alarm signal input No 8 8 Infrared alarm signal input No 9 9 Infrared alarm signal input No 10 10 Infrared a
19. ave and quit menu 3 Left click the icon in the menu to enter sub menu use the middle wheel of mouse to change parameters and then left click SAVE to save the parameters and quit the sub menu Click the CANCEL to quit the menu without save parameters 4 Go Back to the main menu right click the mouse to quit the system setup menu 3 2 CAMERA Move the cursor to CAMERA icon and press ENTER to enter the CAMERA sub menu EM 8 CAMERA CHIA NINIEiI Avi COLOR I4 LE CAMO S5 PTZ PROTOCOL PELCO P PTZ ADDRESS 5 EVENT POPUP OFF MAIN ROT TIME 1 CHANNEL Press LEFT RIGHT button to choose the channel ALL is to choose all channels 2 COLOR Move the cursor to COLOR press ENTER button to enter the COLOR sub menu press LEFT or RIGHT button to set the parameters 3 TITLE COLOR CONTRAST BRIGHTNESS HUE SATURATION SHARPNESS 1 Contrast to adjust contrast of the channel image 2 Brightness to adjust brightness of the channel image 3 Hue to adjust hue of the channel image 4 Saturation to adjust saturation of the channel image 5 Sharpness to open or close the image sharpness of the channel image Front panel 1 Press UP DOWN LEFT RIGHT button to select the letters of keyboard box and change the channel s title Press ENTER button to input the letters Move the cursor to the symbol of keybo
20. d install the hard disk with the screws and connect the cables 4 After checking all connections without any problems connect the power adaptor and plug in DVR will be automatically turned on 5 If DVR turned off by POWER button it can be turned on by POWER button again 2 2 Turn off the DVR 1 Normally do not turn off the machine during recording playing or system setting up Long time press POWER button about 2 seconds to turn off the DVR 2 The DVR will display power off dialog box press ENTER to turn off and press CANCEL to keep power on Note If turn off the DVR during recording the DVR will check the last working condition when turn on again It will take a longer time to start up 3 Mouse Left click MENU button on the left of the bottom status bar then select the submenu shut down to turn off the DVR 4 If the DVR is not in use for a long time please unplug the power cord 2 3 Display mode 1 Press the MODE button to choose the display modes and press channel button to display single channel Mouse Left click the MENU on the left of the bottom status bar choose LIVE to enter display modes click to choose different display mode In multichannel display mode keep the left click of the mouse on the selected channel and drag the channel can be changed to another place of the screen 2 Auto switching channel can display each channel in turn first set the switch time in t
21. e 4 NETMASK The setting method is same with IP setting 5 GATEWAY The setting method is same with IP setting 6 NAME SERVER The setting method is same with IP setting 7 DDNS Press ENTER button to enter DDNS setting menu 1 SERVER Open or close the DDNS server 2 HOST NAME Input the DDNS domain name 3 USER NAME Input the DDNS user name 4 PASSWORD Input the DDNS domain user password 5 xDSL ROUTER The default is OFF DDNS SERVER HOST NAME USER NAME PASSWORD xDSL ROUTER 3 8 BACKUP 1 When the DVR connect the backup device CD ROM or USB for about ten seconds move the cursor to BACKUP icon and press ENTER button to enter the BACKUP sub menu BACKUP DISK DD DEVICE USB CHANNEL NLL CHANCE START 2008 09 26 17 END 008 09 27 10 TOTAL MB 1 DISK Choose hard disk for backup when more than one hard disks used 2 DEVICE Backup device 3 CHANNEL The channel to backup ALL is to choose all the channels 4 START The start time to backup 5 END The end time to backup 6 TOTAL The size of the backup data 7 AVI The AVI format for backup data 2 Press ENTER button to start backup WARNING BACKUP COMPLETED 4 Press ENTER button to finish backup After the DVR displays BACKUP sub menu again can remove the backup device 5 When using mouse left click the small circle icon on top right of BACKUP sub menu to start to
22. fault setting only input IP address and click After open of the remote viewer click display mode icons on the bottom right to change the display mode as following iji z 212221531111 i e 8 perpyrpyrrrs Ne rs Lad fet ec AC u ae Fc Fac vet Tc ec ut ELI D 5 a 1 FM UN me ns pm oz Qua Qo Qi P5 L B LB EB BB P6 5 Double click the one channel picture to display the full channel picture double click again to go back to quad display Save CamNo 01 Image Save Image All Print CamNo 01 Image Reset CamNo 01 Channel Reset Channel All P7 1 Save CamNo 01 Image Save the channel 1 image as JPG format Right click one channel picture such as CamNo 04 to save the Channel 4 2 Save Image All Save all images as JPG format 3 Print CamNo 01 Channel Print the channel 1 image Right click one channel image such as CamNo 03 to print the Channel 3 4 Reset CamNo 01 Channel Reset the Channel 1 image 5 Reset Channel All Reset all channels images Connect xq Connect 6 Click to stop the remote viewer click again to input the password and click OK to enter the remote viewer T Recording to AVI format AVI Click a and Qu will change to blue color to start recording Click m AVI again to stop recording The AVI file can be played by WINDOWS player Note When recording to AVI file the live cha
23. he menu then press AUTO button on the front panel to start the auto switch function Mouse Left click the MENU on the left of the bottom status bar choose ROTATION to start auto switch function 3 Zoom of the images only for mouse operation Mouse Left click the MENU on the left of the bottom status bar choose ZOOM to enable Zoom function keep the left click of the mouse and drag it to select zoom erea If selecting full screen it will return back the normal size Right click the mouse to quit from Zoom function 2 4 Normal record 1 Connect video inputs 2 Choose the record modes always record emergency record manual record schedule record The factory default is always record 3 Press REC button to manual record 8 16 channels video 4 Press REC button to stop manual record 5 During recording if the hard disk is full and the system set to automatically overwrite then the recording will not be interrupted and it begins to overwrite the earliest recorded area if the system set to disable overwrite it will stop recording when the hard disk is full Note Normal recording can only be operated by front panel or remote controller the mouse can t operate manual record 2 5 Alarm record 1 Alarm record cannot be started by REC button 2 Alarm record can be activated by alarm input signal or motion alarm so need to check alarm inputs first and make sure the inputs are stable a
24. ie cad Ssttiaqu Ade si strato Bp totes ower x P1 HetViewer Network Viewer and display as following 2 Double click g DENN Min 4 AMEN gu Ep us n 0 Ox On Gr P2 3 Click the SETTING button marked with red color display as following Network Viewer Setting Network AVI Seve IP Au LS lg Video Size Fullsi Malfsi Video SC C PAL TCP Port number 2200 Saree Frane Sec 15 a Common AVI Codec Network Don t care v Cinepak Codec by Redivs Intel Indeo qo Video R3 2 Intel Indeo Video R3 2 Mex Channel 16 CY Intel Indeo Video 4 5 Intel IYUV codec Codec 54 Microsoft Video 1 Indeo video 5 10 Local rec ic uvm Adjust window 720 480 Mide title bar in full screen Cancel P3 IP Addr pem mg Input IP Add in the and click the Lx to exit the menu xq Connect 4 Click the icon and display as following BPeriewsk Picwec uu gt NETWORK METEO neat WH Oe METUS VIEWER uw o vues o vuv MET Ov METH ov HET os NETUS v view view gt Wwe gt uw o e P ta X b ewe 18 e METRO LESEN Troe views vew Lol feet i e Dow PPa NETOS NETWOS NET WHOS NETOS s view o vurwr o wur view E tt uu ttm be on ante om x Web Mime EH LU uie HH A fee t r to Que Qum P4 The DVR IP address in the mia z Input password in e box Click ema to exit click x to enter remote viewer Note No need password for DVR de
25. ight is off 25 Shuttle switch control During DVR playback use the outer ring of this switch to rewind or fast forward Use the inner ring to playback with single frame 26 Mouse port Connection with USB mouse 27 USB port Connection with USB disk for updating firmware and backup files Can not use USB mouse to this port 28 CD RW mount For mounting CD RW driver remove the front pannel when install CD RW driver Function of the front panel 16CH 1 MENU button Press this button to enter main menu press CANCEL button to quit menu After setting parameters in menu press MENU button to save and quit menu 2 POWER button In display mode long press the button for more than 2 seconds and DVR will display power on off dialog box press CANCEL button to give up turning off DVR and return back to display mode Press ENTER button to turn off DVR If DVR turned off by POWER button can press POWER button again to turn on DVR 3 ENTER button In display mode press this button to enter popup menu press UP or DOWN button to move the cursor Re press ENTER button to enter sub menu Press CANCEL button to quit menu When playback ENTER button is a pause button In PTZ operation mode press ENTER button to enter pre set position function 4 t PUP button After press MODE button press t UP button to select display mode Under menu o
26. larm signal input No 11 11 Infrared alarm signal input No 12 12 Infrared alarm signal input No 13 13 Infrared alarm signal input No 14 14 Infrared alarm signal input No 15 15 Infrared alarm signal input No 16 16 Infrared alarm signal input No 17 Alarm output GND Ground No 18 Alarm output N C Normally Closed No 19 Alarm output N O Normally Open No 20 Alarm output COM Common No 21 RS 485 A No 22 RS 485 B 1 5 Infrared remote controller 1 POWER Turn on off the DVR 2 REC Record 3 SEARCH File search 4 B pause play 5 EZI Rewind 6 DJ Fast forward 7 MENU DVR menu 8 CANCEL Quit from the menu 9 PTZ PTZ control 10 BACKUP Backup the information 11 MUTE Audio on off 12 ES cHi UP 13 AUTO Automatically switch channel 14 El CH4 LEFT 15 Z Enter control 16 LA CH2 RIGHT 17 MODE Display mode 18 kd CH3 DOWN 19 NUMERAL BUTTON Switch to the channel as the button indicates II Operation Guideline Before using the DVR please set up system according to user guide Keep the machine work in the right way When installing new hard disk it must be formatted by DVR system menu 2 1 Turn on the DVR 1 Before power on please make sure all the items in the Security Notice at the beginning of this manual are fulfilled 2 Before power on please check the system connection keep inputs and outputs in correct connections 3 Open the cover of the DVR an
27. m the menu password Front panel 1 Choose PASSWORD Press ENTER button to input password 2 Press UP DOWN LEFT RIGHT button to select the characters of keyboard box Press ENTER button to input the characters Move the cursor to the symbol of keyboard box and press ENTER button to delete the chosen letters 3 Move the cursor to ENTER of keyboard box and press ENTER button to quit from the menu 4 Press MENU button to save and quit from menu 5 Press CANCEL button to quit from menu without save Mouse 1 Move the cursor to PASSWORD and CONFIRM in the SYSTEM PASSWORD sub menu Left click the SET to enter keyboard box 2 Left Click the characters and click ENTER to save and quit Right click the mouse to quit the menu without save Note The default is no password The user can set the password if need The DVR general password is 666666 4 SYSTEM INFO Move the cursor to choose the SYSTEM INFO and press ENTER button to enter SYSTEM INFO sub menu as following SYSTEM INFO FIRMWARE VER PRI MASTER SLAVE SEC MASTER SLAVE HDD OVERWRITE OW UOCE s The SYSTEM INFO sub menu displays the following information 1 FIRMWARE VER Display the DVR firmware version 2 PRI MASTER The size and capacity of the first master hard disk 3 PRI SLAVE The size and capacity of the first slave hare disk 4 SEC MASTER The size and c
28. nd reliable Referring to sensor setup and motion detection setup 3 Setting the record mode before recording 4 As long as the alarm input signal is effective the alarm keeps recording When no alarm input signals alarm recording will keep recording for the time set in menu and then stop recording automatically 5 Entering menu to change recording mode if no need alarm recording if there is a password for setup input correct password 2 6 Schedule Record Ru Cv de SCHEDULE Aa V 8 10 12 14 16 18 20 22 24 1 Schedule record starts or stops recording automatically according to the pre set time It set in a pre set timetable for example to set a periodical recording 2 There are 5 schedule record lists for your choice choose the suitable schedule accord to the requirement 3 Before using this function make sure the time setting correctly 4 Only in the menu can change and quit schedule recording Note Different color symbols indicate the different record modes the detailed information as following Normal mode The green symbol in the middle of the screen Always mode The blue symbol in the middle of the screen Motion alarm mode The red symbol in the middle of the screen Sensor alarm mode The orange symbol in the middle of the screen Schedule mode The purple symbol in the middle of the screen 2 7 Playback Front panel 1 Press SEARCH button DVR will display SEARCH MENU the user can choose TIME
29. nnel images are not smooth 8 Recording to DVR format Backup Loca d Click an will change to green color to start recording Backup Click again to stop recording The file can only be played by DVR Local rec Ic Documents an Note Setting the save path in the before recording The remote recording and local recording can be operated simultaneously 5 2 Menu 1 Live display Control the PTZ operation of DVR When controlling PTZ operation first select one channel display then can control PTZ Press UP DOWN LEFT and RIGHT icons to control the PTZ operation for cameras ZOOM Press ES to zoom in and press Q to zoom out release the button to stop the zoom FOCUS Press GP to adjust focus far from object press T to adjust focus near from object release the button to stop adjusting focus IRIS Press Ge to adjust iris open press Gal to adjust iris close release the button to stop adjusting iris AUTO Left click the button to start the auto rotation press again to stop the auto rotation 2 Playback Click the button to play HDD data of DVR on your PC Lue Eeh itu 0000 Ta foe how wu wet 4 Sj P8 1 Move the cursor to the date box to choose the date of the recorded data 2 Move the cursor to the time box to choose the time of the recorded data 3 Click Q to play record Click to play forward one frame by one frame Click D to play rewind one frame by one frame Click Q to stop
30. ower adaptor The damages are caused by natural disasters such as fire flood tide and lightning etc O Changing HDD Feature Non pc stand alone security digital video recorder with embedded operation system H 264 compression format Safe and friendly power on power off function Chinese English Korea Japanese languages supported Audio and video real time recording and playback function Support NTSC PAL video system 8 16CH video inputs 1CH monitor output 1CH VGA output optional 4CH audio inputs 1CH audio output High quality image brightness sharpness and color adjustable for each channel Support multiple zoom by mouse Support auto switch for each full screen display Display modes PIP full screen 4images 8 images 16 images Recording modes emergency recoding scheduled recording alarm recording and motion recording Image quality highest high normal low Detailed event log support Searching modes time data searching event searching recording group searching Support fast forward and rewind X2 X4 X6 Backup modes network backup USB 2 0 backup CD ROM backup optional Support RS 485 PTZ control speed dome camera and preset positions operation Support USB mouse and infrared remote controller operation Support 4 SATA port HDD 8 16 CH alarm inputs 1 CH alarm control output Multiplex operation live record playback network can be operated at the same time Support network function remote monitor remote playback remo
31. peration and PTZ control it is Upward key 5 DOWN button After press MODE button press P DOWN button to select display mode Under menu operation and PTZ control it is Downward key 6 PLEFT button After press MODE button press lt LEFT button to select display mode Under menu operation and PTZ control it is Leftward key 7 P RIGHT button After press MODE button press RIGHT button to select display mode Under menu operation and PTZ control it is Rightward key 8 CANCEL button In menu or PTZ operation mode press this button to quit menu or PTZ operation mode In playback mode press this button to stop playback 9 Channel button Full screen display one selected channel by pressing numeral button 10 MODE button Repeat pressing this button to display image in different modes PIP1 PIP2 PIP3 four pictures nine eight pictures In PTZ operation mode press MODE button to enter focus control then adjusted by lt button and button Press it again to quit focus control 11 AUTO button In display mode press this button to enter auto switch for single channel The user can set the switching time The DVR can display each channel in turn for this time Press again to quit from auto switch In playback mode repeat press AUTO button to rewind frame by frame prss ENTER
32. port Confidential Function Password Protection Power Supply DC 12V 5A Power Consumption No 20W HDD Environment Work Temp 5 C 50 C Storage Temp 20 C 707 Dimension 430 X 390 X 120mm 430X390 X 70mm Weight 3kg No HDD Note Specifications and appearance are subject to change without notice
33. s BACHUP button to enter BACKUP MENU 3 Press LEFT or RIGHT to move the cursor press UP or DOWN button to set the start time of backup and the end time of backup 4 Choose the backup format to AVI format DVR default format press ENTER button to start backup 2 13 Checking System Information SYSTEM INFO FIRMWARE VER PRI MASTER SLAVE SEC MASTER SLAVE HDD OVERWRITE v X Sate d A as n 1 Press MENU to enter DVR system menu 2 Choose SYSTEM menu move the cursor to SYSTEM INFORMATION menu then press MENU button to enter DVR system menu SYSTEM INFO FIRMWARE VER PRI MASTER 931 Gt SLAVE NONE SEC MASTER NONE SLAVE NONE HDD OVERWRITE ON It displays the software version of DVR the master hard disk information and the slave hard disk information HDD OVERWRITE the system will automatically overwrite if it set to ON The DVR will stop recording when hard disk is full if HDD OVERWRITE set to OFF 3 Press CANCEL button to quit from system menu 2 14 PTZ Control front panel 1 In the full channel mode press PTZ button on front panel or remote controller to enter PTZ function Press UP DOWN LEFT or RIGHT button to control the rotation of PTZ then press ENTER to enter the pre set menu Note Only keep pressing UP DOWN LEFT or RIGHT button to control the rota
34. setting SYSTEM SETUP Default Items f Optional Setting Setting Password NO Setting by keyboard box Sequence Time 4 seconds 0 10 seconds Buzzer ON ON OFF General System Log ON ON OFF Setup Video System NTSC NTSC PAL Video Color 50 1 100 adjustable Audio 1234 1234 OFF Overwrite Open Open Close 240f s NTSC Record Speed NO 200f s PAL Record i CIF CIF 1 2D1 DI Resolution 240f s NTSC Playback Speed NO 200f s PAL Record Audio Selectable ON CH1 CH2 CH3 CH4 OFF Parameter Alarm Rec Time 5 seconds 5 60 seconds Pre record ON ON OFF S Always Motion Alarm Schedule Setting Always Sensor Alarm OFF Motion Detection Sensor Record Mode Manual Schedule Always Emergency Manual PTZ Protocol PELCO D PELCO D PELCO P PTZ PTZ Address 123456 0 255 Optional Pre set Position Support 255pcs position Sub netmask 255 255 255 0 Optional Network Gateway 192 168 1 1 Optional Setup IP Addrss 192 168 1 152 Optional Port 2200 Optional Motion Detection ON ON OFF Motion Area NO Selectable Alarm Setup Sensitivity LEVEL 4 LEVEL 1 LEVEL 8 Buzzer Time 5 seconds 5 60 seconds Schedule Setup Always eee Sensor Alarm OFF V PC Viewer Operation 5 1 Steps of operation 1 Install the PC viewer software from CD to your PC As following LADGIIT ZR sup xev Wu TAD Phew Pe pmr X n CDC hran
35. ss LEFT or RIGHT button to adjust a position of PTZ Press ENTER button to enter SET PRESET menu set the PRESET to 2 and select SAVE then press ENTER button Using the same way to set other pre set position The DVR support 255 pre set positions In SET PRESET menu set the PRESET to one number then select LOAD icon and press ENTER button to move PTZ to reach its pre set position 4 The setting of the pre set positions refers to the user manual of speed dome Mouse 1 Left click MENU on the left of the bottom status bar choose PTZ to enter PTZ control mode 2 Left click UP DOWN LEFT or RIGHT icons to control the rotation of the PTZ 3 Left click Z F T to enable ZOOM FOCUS and IRIS function respectively then left click the LEFT or RIGHT to adjust 4 Left click P to enter SET PRESET menu 5 Set the PRESET and SAVE refers to the user manual of speed dome Note Before operating PTZ function it is necessary to check the connections of PTZ The pre set position is used for speed dome that can support pre set function 2 15 Password Input If the password protection is enabled it needs to input the correct password when entering the DVR menu 1 Press MENU button and display password dialog box 2 Press MENU button again to display the keyboard box and press UP DOWN LEFT or RIGHT button
36. start emergency record manual record the color of REC icon on the bottom status bar becomes blue Press REC button again to stop emergency record manual record Note When DVR set to schedule record mode or always record mode the emergency record mode can t be started 16 SEARCH button In display mode or record modes press SEARCH button to enter record events menu Press LEFT or RIGHT button to choose the playback modes time date searching mode or events searching mode Then press ENTER button to play back recorded information press CANCEL button to stop playback 17 lt lt P REWIND button During playback repeat pressing the button to rewind play and the speed can be selected to X2 X4 or X6 18 PAUSE PLAY button During playback press this button to pause or play 19 gt gt PFAST FORWARD button During playback repeat pressing the button to fast forward play and the speed can be selected to X2 X4 or X6 20 Receiver of remote controller 21 Power indicator light After DVR turned on the light is on When pressing POWER button to turn off the DVR the light is flickering 22 Network connecting indicator light When DVR connected to network the light is on Otherwise the light is off 23 Recording indicator light When DVR is recording the light is on Otherwise the light is off 24 Playback indicator light During DVR playback the light is on Otherwise the l
37. te record and so on Live display 8CH 240fps NTSC 200fps PAL 16CH 480fps NTSC 400fps PAL Live record 8 16CH 240fps NTSC 200fps PAL 8CH CIF real time recording I Content System Installation 1 1 Accessories 1 2 Introduction of the front panel 1 3 Introduction of the rear panel 1 4 Connection of the rear panel 1 5 Introduction of the infrared remote controller II Operation Guideline Il 2 1 Turn on the DVR 2 2 Turn off the DVR 2 3 Viewing Operation 2 4 Manual record operation 2 5 Alarm record operation 2 6 Schedule record operation 2 7 Playback operation 2 8 Record time searching 2 9 Record group searching 2 10 Event group searching 2 11 USB backup 2 12 CD ROM backup Optional 2 13 Checking system information 2 14 PTZ control 2 15 Password input System Menu Setup 3 1 Main menu 1 Front panel 2 Mouse 3 2 CAMERA 1 CHANNEL 2 COLOR 3 TITLE 4 PTZ PROTOCOL 5 PTZ ADDRESS 6 EVENT POPUP 7 MAIN ROT TIME 3 3 RECORD 1 CHANNEL 2 RESOLUTION 3 PRE RECORD 4 FPS 5 QUALITY 6 RECORD MODE 7 AUDIO 8 SCHEDULE 3 4 MOTION 1 CAMERA CHANNEL 2 MOTION ENABLE 3 SENSITIVITY 4 MOTION AREA 5 POST RECORD TIME 6 BUZZER TIME 7 ALARM TIME 8 MOTION TRACE 3 5 SENSOR 1 SENSOR CHANNEL 2 SENSOR TYPE 3 POST RECORD TIME 4 BUZZER TIME 5 ALARM TIME 3 6 SCHEDULE 3 7 NETWORK 1 IP MODE 2 PORT 3 IP 4 NETMASK 5 GATEWAY 6 NAME SERVER 7 DDNS 3 8 BACKUP 3 9 SYSTEM 1 T
38. tion of PTZ when button released the PTZ will stop rotation Press MUTE button to enable IRIS function Then keep pressing LEFT or RIGHT button to adjust the iris of camera button released to stop adjusting the iris Press AUTO button to enable AUTO function the PTZ will automatic rotate press again to stop Press BACKUP button to enable ZOOM function of camera press LEFT or RIGHT button to adjust the zoom of camera button released to stop ZOOM function Press MODE button to enable FOCUS function of camera press LEFT or RIGHT button to adjust the focus of camera button released to stop FOCUS function Press CANCEL button to quit from PTZ function Pre set Position Function 1 After entering PTZ control mode press ENTER button to enter the setting menu of pre set position SETPRESET PRESET AUX SPEED 2 Press UP or DOWN button to move cursor and press LEFT or RIGHT button to select setting number then press ENTER button to confirm 3 PRESET a After entering the SET PRESET menu set the PRESET to 1 and select SAVE then press ENTER button to save current PTZ position to 1 b Quit from SET PRESET menu and back to PTZ mode press LEFT or RIGHT button to move the speed dome camera to next pre set point setting ZOOM IRIS or FOCUS and pre
39. to move cursor then press ENTER button to input password and select on the keyboard box to clear Input the correct password and move the cursor to ENTER press ENTER button to confirm the correct password 3 After quit from the keyboard box press MENU button to enter the system menu III System Menu Setup 3 1 Main menu Front Panel Press Menu button on the front panel to enter system menu press UP DOWN button to move the cursor press ENTER button to enter the sub menu Press LEFT RIGHT button to select item and press MENU button to save and quit Or press CANCEL button to quit from the menu without save The system menu display as following N Ea em cm crm cmm NT as E G LL 6 Mouse 1 Left click Menu to display the DVR function menu and select SETUP to enter DVR system setup menu PTZ ROTATION IA UD 10 ON QU LIVE Choose the display mode SETUP Enter the system setup mode SEARCH Enter the playback menu MOTION Open or close the motion alarm function ZOOM In the full channel mode select the ZOOM function Only using mouse to operate the ZOOM function PTZ In the full channel mode select PTZ to control PTZ function ROTATION Select the auto switch function for each channel AUDIO Turn on off audio QUIT Turn off the DVR 2 In the sub menu left click the small circle icon on the top right to s
40. to quit and back to normal playback In PTZ operation mode press AUTO to control the PTZ auto rotation press again to stop auto rotation of PTZ 12 MUTE button In display mode press MUTE button to turn on and turn off the audio In PTZ operation mode press MUTE button to enter iris control then adjusted by button and button Press it again to quit iris control 13 BACKUP button In display mode if there is USB CD burner to connect the DVR press the button to backup the information Choose the start time and the end time of the backup and press ENTER button to backup When backup is completed the system automatically quit from the menu If there isn t backup device to connect to the DVR the DVR reminds can t find the backup device and press CANCEL button to quit from the menu 14 PTZ button In single channel display or record mode press this button to enter PTZ operation press this button and button to adjust zoom ratio of camera press PTZ button again to quit zoom ratio adjustment press CANCEL button to quit from PTZ operation In playback mode press this button to forward display frame by frame press enter return to normal playback speed 15 REC button When setting DVR record mode to OFF in the menu press the REC button to start emergency record manual record the color of REC icon on the bottom status bar becomes bl
41. ue Press REC button again to stop emergency record manual record Note When DVR set to schedule record mode or always record mode the emergency record mode can t be started 16 SEARCH button In display mode or record modes press SEARCH button to enter record events menu Press LEFT or RIGHT button to choose the playback modes time date searching mode or events searching mode Then press ENTER button to play back recorded information press CANCEL button to stop playback 17 P REWIND button During playback repeat pressing the button to rewind play and the speed can be selected to X2 X4 or X6 18 PAUSE PLAY button During playback press this button to pause or play 19 gt gt PFAST FORWARD button During playback repeat pressing the button to fast forward play and the speed can be selected to X2 X4 or X6 20 Receiver of remote controller 21 Power indicator light After DVR turned on the light is on When pressing POWER button to turn off the DVR the light is flickering 22 Network connecting indicator light When DVR connected to network the light is on Otherwise the light is off 23 Recording indicator light When DVR is recording the light is on Otherwise the light is off 24 Playback indicator light During DVR playback the light is on Otherwise the light is off 25 Shuttle switch control During DVR playback use the outer ring of this switch to rewind or f

8and 16 channel dvr manual

Contents

Download Pdf Manuals

Related Search

Related Contents