LB3000/LB3000PS Lock Box Installation/ Operation Manual
Contents
1. LB3000 LB3000PS Lock Box Installation Operation Manual C1907M 8 00 Pelco 3500 Pelco Way Clovis CA 93612 5699 USA www pelco com In North America and Canada Tel 800 289 9100 FAX 800 289 9150 International Customers Tel 1 559 292 1981 e FAX 1 559 348 1120 IMPORTANT SAFEGUARDS AND WARNINGS Prior to installation and use of this product the following WARNINGS should be observed 1 Installation and servicing should only be done by qualified service personnel and con form to all local codes 2 Unless the unit is specifically marked as a NEMA Type 3 3R 3S 4 4X 6 or 6P enclo sure it is designed for indoor use only and it must not be installed where exposed to rain and moisture 3 The installation method and materials should be capable of supporting four times the weight of the unit and equipment 4 Only use replacement parts recommended by Pelco 5 After replacement repair of this unit s electrical components conduct a resistance measurement between line and exposed parts to verify the exposed parts have not been connected to line circuitry 6 Ifthe unit has fuses replace fuses only with the same type fuses for continued protec tion against risk of fire The product and or manual may bear the following marks This symbol indicates that dangerous volt age constituting a risk of electric shock is present within this unit CAUTION RISK OF ELECTRIC SHOCK j This symbol indic2. or Puerto Rico and are instructed to return goods to the USA you may do one of the following If the goods are to be sent by a COURIER SERVICE send the goods to Pelco 3500 Pelco Way Clovis CA 93612 5699 USA If the goods are to be sent by a FREIGHT FORWARDER send the goods to Pelco c o Expeditors 473 Eccles Avenue South San Francisco CA 94080 USA Phone 650 737 1700 Fax 650 737 0933 Pelco the Pelco logo PelcoVision Camclosure Esprit Genex Legacy and Spectra are registered trademarks of Pelco Endura and ExSite are trademarks of Pelco Copyright 2000 Pelco All rights reserved 8 Pelco Manual C1907M 7 00
3. 3 3 x 48 3 cm MCS16 10 POWER SUPPLY LB3000PS ONLY Input Voltage Output Voltage Outputs Supply Current Max Current per Channel Required Input Current 120 VAC 240 VAC Surge Protection Output Fuse Rating Output Connectors Output Wire Size Construction 120 or 240 VAC 50 60 Hz 24 28 VAC 16 10A 3A 2 20A 1 15A Yes 3A Screw type barrier strips 12 22 gauge solid or stranded wire Steel Design and product specifications subject to change without notice PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace without charge any merchandise proved defective in material or workmanship for a period of one year after the date of shipment Exceptions to this warranty are as noted below Five years on FT FR8000 Series fiber optic products Three years on Genex Series products multiplexers server and keyboard Three years on Camclosure and fixed camera models except the CC3701H 2 CC3701H 2X CC3751H 2 CC3651H 2X MC3651H 2 and MC3651H 2X camera models which have a five year warranty Two years on standard motorized or fixed focal length lenses Two years on Legacy CM6700 CM6800 CM9700 Series matrix and DF5 DF8 Series fixed dome products Two years on Spectra Esprit ExSite and PS20 scanners including when used in continuous motion applications Two years on Esprit and WW5700 Series window wiper excluding wiper blades Eighteen months on DX Ser
4. BOX MOUNTING STUDS Figure 2 Mounting Plate Pelco Manual C1907M 7 00 Pelco Manual C1907M 7 00 11 12 13 14 15 16 Fasten the lock box to the mounting plate refer to Figure 2 Place the top back side of the lock box over the mounting tabs on the top of the mounting plate Open the lock box door and make sure the mounting studs in the bottom of the mounting plate go through the stud holes in the bottom of the lock box Replace the nuts removed in step 3 Replace the bottom tape shelf removed in step 2 Install the VCR and multiplexer Refer to the manuals supplied with the equipment Un Screw and remove the access panels in the top and sides of the lock box to reach the back of the equipment to make wiring cabling connections Optional Place a monitor on top of the lock box Connect a video cable to the moni tor Drop the video cable and power cord from the monitor through the round hole in the top of the lock box Connect the video cable to the multiplexer and the power cord to a power outlet Turn on all equipment and program the VCR and multiplexer according to the manuals supplied with the equipment Turn on all equipment and program the VCR and multiplexer according to the manuals supplied with the equipment POWER SUPPLY INSTALLATION WARNING Pelco shall not be liable for any damages resulting from incorrect wiring or improper loading of the MCS16 10 Master Power Supply CAUTION Unde
5. ates that there are impor DO NOT OPEN tant operating and maintenance instructions in the literature accompanying this unit Please thoroughly familiarize yourself with the information in this manual prior to installation and operation Pelco Manual C1907M 7 00 DESCRIPTION The LB3000 LB3000PS Lock Box fastens to a wall to provide a secure enclosure for CCTV equipment refer to Figure 1 The LB3000PS includes a 24 VAC power supply that can power up to 16 cameras 12 vA maximum per camera Two locking latches on the front door prevent unauthorized entry A monitor can be placed on top of the lock box ET LER m mn eee EE CN 1 5 6b566666666556666 o e Go S MULTIPLEXER b 6 1 ver of Id j fO R 1O STORAGE oj SHELF E O OO SHELF FOR 16 TAPES o CI ILI HC oO ol emi l sur FOR il 16 TAPES D Jlo o Figure 1 LB3000 LB3000PS Lock Box Pelco Manual C1907M 7 00 3 INSTALLATION 10 Open the front door of the lock box Remove the bottom tape shelf Reach inside the lock box and remove the two nuts from the mounting studs on the bottom of the rear mou
6. e required to power the cameras Install and connect power wires from the cameras to the power supply For each cam era attach one wire to the COM terminal and the other wire to either the 24V or 28V terminal refer to Figure 3 Double check the installation for safety purposes Plug in the power cord and turn on the power supply Use a voltmeter to verity that the used outputs are at the appropriate voltage levels Return to step 10 of the nstallation section to complete the installation OUTPUT 4 1 24 VAC OUTPUT 1 THRU 8 OUTPUT 9 THRU 16 PELLI 7 MCS16 20 Master Power Supply M Usk O Figure 3 Power Supply Wiring Diagram Pelco Manual C1907M 7 00 APPENDIX Table A Video Coaxial Cable Requirements Table B Power Supply Product Capacity Cable Type Maximum Distance Product MCS16 10 RG59 U 750 ft 229 m CCD Camera 12 vA maximum 16 RG6 U 1 000 ft 305 m DF5 DF5S with camera 3 vA 16 RG11 U 1 500 ft 457 m DF8A PDF8 12 vA maximum 16 Indoor Spectra 30 vA 8 Minimum cable requirements Esprit 50 vA 4 75 ohms impedance All copper center conductor All copper braided sh
7. ield with 95 braid coverage Table C Recommended Wiring Distances for Power Supply The following are the recommended maximum distances transformer to load and are calculated with a 10 percent voltage drop Ten percent is generally the maximum allowable voltage drop for AC powered devices Input Total vA Wire Gauge Voltage Consumed 20 18 16 24 VAC 10 283 ft 86 m 451 ft 137 m 716 ft 218m 20 141 ft 42 m 225ft 68m 358ft 109 m 30 94ft 28m 150ft 45m 238ft 72m 50 56ft 17m 90ft 27m 143 ft 43m 28 VAC 10 386ft 117 m 614ft 187 m 975ft 297 m 20 193ft 58m 307ft 93m 487 ft 148 m 30 128ft 39m 204ft 62m 325 ft 99 m 50 778 23m 122ft 37m 195ft 59 m Required Wire Gauge Table AWG i Equipment Loads VA P T480 s Pan Tilt PT570 s Pan Tilt Esprit S Pan Tilt amp Outdoor ES Spectra 2 als JS E SERERE 800 Et American Wire Gauge AWG Using 24 Volt Tap N American Wire Gauge AWG Using 28 Volt Tap N A Distance and Load Not Recommended For Any Wire Size Between 12 22 AWG Pelco Manual C1907M 7 00 SPECIFICATIONS LOCK BOX Construction Cabinet Mounting Plate Mounting Plate Support Finish Environment Dimensions Weight LB3000 LB3000PS Aluminum Steel Steel Charcoal gray polyester powder coat Indoor 29 0 H x 21 0 W x 19 0 D inches 73 7 x 5
8. ies digital video recorders NVR300 Series network video recorders and Endura Series distributed network based video products One year except video heads on video cassette recorders VCRs Video heads will be covered for a period of six months Six months on all pan and tilts scanners or preset lenses used in continuous motion applications that is preset scan tour and auto scan modes Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment All goods requiring warranty repair shall be sent freight prepaid to Pelco Clovis California Repairs made necessary by reason of misuse alteration normal wear or accident are not covered under this warranty Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products Pelco s liability for any claim whether based on breach of contract negligence infringement of any rights of any party or product liability relating to the Products shall not exceed the price paid by the Dealer to Pelco for such Products In no event will Pelco be liable for any special incidental or consequential damages including loss of use loss of profit and claims of third parties however caused whether by the negligence of Pelco or otherwise The above warranty provides the Dealer with specific legal rights The Dealer may also have additional rights which are subject to variation from
9. nting plate refer to Figure 2 Remove the mounting plate pull out a few inches on the bottom of the plate and then pull downward to release the mounting tabs at the top of the plate Place the mounting plate against the wall and mark the eight holes for attaching the lock box to the wall The mounting holes on each side of the plate are spaced 16 inches apart so the plate can be fastened to standard wall studs Also outline the cable entry opening Refer to Figure 2 Drill pilot holes for 3 8 inch diameter wood screws Cut out the opening for cable access Provide 120 or 240 VAC power receptacles for the following VCR multiplexer monitor if it is going to be placed on top of the lock box MCS16 10 Master Power Supply LB3000PS only Fasten the mounting plate to the wall studs with 3 8 inch diameter wood screws LB3000PS Only Install the MCS16 10 Master Power Supply Refer to the Power Supply Installation section Bring all video cables for the cameras through the opening in the wall Refer to Table A in the Appendix for the type of video coaxial cable to use It is not necessary to bring any wiring through the wall for the VCR or a monitor placed on top of the lock box If you are going to wire other remote equipment monitors alarms or keyboard to the multiplexer refer to the multiplexer and keyboard manuals for wiring requirements MM Ad LOCK BOX MOUNTING TABS CABLE ENTRY POWER SUPPLY MOUNTING STUDS LOCK
10. r A N light load conditions and high power line input voltage from the utility company output voltage from the power supply 28 VAC taps only could exceed 32 VAC This voltage can cause over voltage damage on 24 VAC devices Keep in mind certain devices produce variable loads due to heaters blowers and pan and tilt motion and during minimum requirements may create a light load condition causing excessive voltage Therefore Pelco recom mends using a 28 VAC tap only when the supplied wire size for the given load causes an unacceptable output voltage on the 24 VAC tap Refer to Table D in the Appendix to determine acceptable situations for the 28 VAC tap LB3000PS Model Only T Fasten the power supply to the mounting plate with the supplied lock washers and nuts refer to Figure 2 Verify that the on off switch is OFF Remove the high voltage compartment panel refer to Figure 3 Set the input voltage selector switch to the appropriate line voltage Remove the spare fuse bag from the high voltage compartment The power supply is shipped with a fuse installed for 120 VAC operation If you are going to use 240 VAC remove the 3 ampere fuse from the fuse holder and replace it with a 1 6 ampere fuse from the fuse bag Replace the high voltage compartment panel Refer to Table B in the Appendix for the number of cameras the power supply can power Refer to Tables C and D in the Appendix to determine the size of wir
11. state to state REVISION HISTORY Manual Date C1907M 7 00 Comments Original version If a warranty repair is required the Dealer must contact Pelco at 800 289 9100 or 559 292 1981 to obtain a Repair Authorization number RA and provide the following information 1 Model and serial number 2 Date of shipment P O number Sales Order number or Pelco invoice number 3 Details of the defect or problem If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above please include a written explanation with the product when returned Method of return shipment shall be the same or equal to the method by which the item was received by Pelco RETURNS In order to expedite parts returned to the factory for repair or credit please call the factory at 800 289 9100 or 559 292 1981 to obtain an authorization number CA number if returned for credit and RA number if returned for repair All merchandise returned for credit may be subject to a 20 restocking and refurbishing charge Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid Ship to the appropriate address below If you are located within the continental U S Alaska Hawaii or Puerto Rico send goods to Service Department Pelco 3500 Pelco Way Clovis CA 93612 5699 If you are located outside the continental U S Alaska Hawaii
Download Pdf Manuals
Related Search