EL512.256-H Series 512 x 256 Pixel
Contents
1. Power consumption 6W 12W 5V 12V Power consumption 4W 7W 5V 12V LOWPWR Operating conditions Frame rate 70 Hz ambient temperature 25 C Note Absolute maximum ratings are those values beyond which damage to the device may occur The minimum and maximum specifications in this Operations Manual should be met without exception to ensure the long term reliability of the display Planar does not recommend operation of the display outside these specifications Display Features Video Data Input Four input signals are needed for video input VS signal marks the topmost row HS envelopes the pixels in one row and VCLK indicates the valid pixel data The visible pixels in a row are the last 512 pixels before the fall of the HS The topmost row displayed is the first HS HIGH time ending after the rising edge of VS If HS is running continuously the rising edge of the VS can be simultaneous to the previous falling or rising edge of the HS See details on the timing as well as setup and hold timing on pages 9 and 10 6 EL512 256 H Series Operations Manual 020 0354 00A or ordering information of el512 256 h3 frb and other EL Displays please visit http www eldisplays com el512 256 h3 frb or call 1 888 394 4998 Two Bit Parallel Data To reduce the input data frequency the video data can be input two bits per clock cycle The two data inputs are organized so that the data for the odd columns numbered from left to the right at t2. Europe and Asia Pacific Support Olarinluoma 9 P O Box 46 FIN 02201 Espoo Finland Tel 358 9 420 01 Hours M F 7 00am 4pm CET 2004 Planar Systems Inc 06 04 Planar is a registered trademark of Planar Systems Inc ICE ICEBrite and ICEPlus are trademarks of Planar Systems Inc Other brands and names are the property of their respective owners Technical information in this document is subject to change without notice 020 0354 00A or ordering information of el512 256 h3 frb and other EL Displays please visit http www eldisplays com el512 256 h3 frb or call 1 888 394 4998
3. 256 h3 frb or call 1 888 394 4998 Optical Determined at 70 Hz frame rate at room temperature Display Colour Wide band amber Zn Mn Table 8 Optical Characteristics Areal Luminance On Luminance typ 65 cd m 19 fL On Luminance min 45 cd m 13 fL Measured at the center and the four corners of the screen Luminance Non uniformity Maximum 35 1 min luminance max luminance x 100 Maximum difference between any two of five points center and four corners Luminance Variation Time Maximum 20 10 000 h Luminance Variation Temperature Typical 10 over 25 65 C range Maximum 15 Viewing Angle Minimum 160 Optional Filter For best overall optical performance of the display a neutral gray circular polarizing filter with anti reflective coating or etch is the usual choice This filter will make the reflective electrodes of the display darker and will improve the contrast ratio The anti reflective coating on the filter should face the user 71 EL512 256 H Series Operations Manual 020 0354 00A or ordering information of el512 256 h3 frb and other EL Displays please visit http www eldisplays com el512 256 h3 frb or call 1 888 394 4998 Mechanical Characteristics Display External Dimensions Fig 6 shows the mechanical dimensions of a standard EL512 256 H series display unit The display can also be delivered with optional FRA aluminium frame or FRB steel frame see Fig 5 and 6 Using FRB f
4. 75 Hz The EL512 256 H displays require 5 Vdc and 11 30 Vdc power input and four basic input signals to operate 1 Video Data or pixel information 2 Video Clock pixel clock or dot clock 3 Horizontal Sync 4 Vertical Sync EL Technology ALUMINIUM ROW ELECTRODE DIELECTRIC LAYERS TRANS PARENT COLUMN ELECTRODE Figure 1 EL Technology A display consists of an electroluminescent glass panel and a mounted circuit board with control electronics The EL glass panel is a solid state device with a thin film luminescent layer sandwiched between transparent dielectric layers and a matrix of row and column electrodes The row electrodes in back are aluminium the column electrodes in front are transparent The entire thin film device is deposited on a single glass substrate The glass panel is mounted to an electronic circuit assembly board ECA with an elastic spacer The ECA is connected to the EL glass panel with soldered lead frames The result is a flat compact reliable and rugged display device 2 EL512 256 H Series Operations Manual 020 0354 00A or ordering information of el512 256 h3 frb and other EL Displays please visit http www eldisplays com el512 256 h3 frb or call 1 888 394 4998 In EL512 256 H series displays the 512 column electrodes and 256 row electrodes are arranged in an X Y formation with the intersecting areas performing as pixels Voltage is applied to both the correct row electrode
5. and the correct column electrode to cause a lit pixel Operating voltages required are provided by an integral DC DC converter Electrical Characteristics Connector Layout J1 Video and Power Input J2 Optional Power Input J3 Control Input PS1 Jumpers oo oo co co SELFTST DCONFIG REAR VIEW Fig 2 Input Connectors and Jumpers and their location 3 EL512 256 H Series Operations Manual 020 0354 00A or ordering information of el512 256 h3 frb and other EL Displays please visit http www eldisplays com el512 256 h3 frb or call 1 888 394 4998 Input to the Display Tablet Input to the Display Pins Signal Symbol Description J1 Data power input connector 1 2 Voltage Vcc2 Supply voltage 11 30V converted to required internal high voltages see J2 3 4 Voltage Vcc1 Supply voltage 5 V for the logic see J2 5 Reserved Reserved do not connect 6 8 10 Ground GND Signal return 7 Two bit data TVID Second data input for two bit parallel mode The TVID input is for odd columns and the VID for even ones 9 Vertical Sync VS The vertical sync signal VS controls the vertical position of the picture 11 Horizontal HS The horizontal sync signal HS controls the Sync internal row counter and the horizontal position of the picture 13 Video Clock VCLK The VCLK signal shifts data present on the VID and TVID lines into the display system VCLK is active on the
6. at a row column intersection The display operation is based on the symmetric line at a time data addressing scheme which is synchronized by the external VS HS and VCLK input signals The internal control signals and the high voltage pulses for the column and row drivers are generated internally by the control electronics All control signal inputs are HCT compatible with pull up resistors Power Input The required supply voltages for the display are 5 Vdc Vcc1 for the logic and 11 30 Vdc input Vcc2 for the integrated DC DC converter The high voltages needed for driving the display are generated by the DC DC converter from the Vcc2 input voltage The input voltages can be connected either through J1 or J2 Signal Inputs Connector J1 contains input for the video signals connector J2 contains two control inputs and connector J3 contains input for external luminance control The signals on J2 and J3 that are not used can be left disconnected Optional Grounding In order to improve the EMC properties of the display system there is an option for the customer to tie together the signal ground of the display and the chassis of the user device For this purpose the four corner mounting nuts are each connected to the signal ground with 10 nF 50 V capacitors When using this option please be aware of the possible risk of lowered isolation strength of the device and possible generation ground loops Connectors Table 2 Connecto
7. npe E 19 Ordering n tob dt ON se niet dae pupodte n mado at capat nd A pp M denda A NU Ried UR 19 or ordering information of el512 256 h3 frb and other EL Displays please visit http www eldisplays com el512 256 h3 frb or call 1 888 394 4998 Figures Figure T EL FeCRInol DO ideae REDon Bes En Oto IUDG tta NPatutie Ra RM RU dae Utt at aid 3 Figure 2 Connector EayOUt otto testo eee etatis pentes coe ep eva Ie oa oa Rea ERE aa 4 Figure 3 Video Input TIMIN g sos se se sp tata Resto Pee a Qasa oii da aequi dua ub QE aU T Mn 9 Figure 4 Setup and Hold TIERIQ uncos ttes cn cac Pt b ta UR Io Bea dit sU ua 10 Figure 5 Viewing Area Chracteristics osi A ps PRA pagi ipii B Roi 14 Figure 6 Front View without Mounting Frame eee ennt tennttesnnttnntttsnnttonnten 14 Figure 7 Back and Side VIEWS sedat une pho bi pA ba A RR RR RA EA PU due 15 Figure 8 Back and Side Views with Aluminum Mounting Frame eere 16 Figure 9 Back and Side Views with FRB Steel Mounting Frame eene 17 Tables Table 1 Input to the Display cnoiar ae a aiias 5 Table 2 Config EOYS eeaeee iet teta e Ereann tM haut dd ms a ttt ido aL 6 Table S PST E E EA betae ttd Ahead i akut eod hb Made i Ao Che 7 Table 4 Input Specifications ou eessssssssscsseesssesssscssscssecsncessccsseccsscsssccssccesscessecsnecsnecssscssscsssccenscsescesacseseesneesseess 7 Table 5 Video IN put FI Ilia aas asp ER EROR REIN RBR TERNI DINER e B
8. rising edge 15 Video Data VID Signal that supplies the pixel information to the system 12 14 Ground GND Signal return 16 J2 Optional power input connector 1 Voltage Vcc2 Same as J1 Pins 1 2 not necessary to connect if power is supplied via J1 2 3 Ground GND Same as J1 Pins 6 8 10 12 14 16 not necessary to connect if power is supplied via J1 Voltage Vcc1 Same as J1 Pins 3 4 not necessary to connect if power is supplied via J1 Low Power Enable _LOWPWR ENABLE J3 Optional control input connector The power consumption of the display is lowered to LOWPWR values if the _LOWPWR is low internally pulled high if left disconnected The operation of the display unit is disabled if the ENABLE input is low internally pulled high if left disconnected 1 Luminance LUMPOT1 Input for external luminance control see Pot 1 page 8 Can be left disconnected 2 Luminance LUMPOT2 Input for external luminance control Can Pot 2 be left disconnected 3 4 Reserved Reserved do not connect 4 EL512256 H Series Operations Manual 020 0354 00A or ordering information of el512 256 h3 frb and other EL Displays please visit http www eldisplays com el512 256 h3 frb or call 1 888 394 4998 Control basics The EL panel has 512 transparent column electrodes crossing 256 row electrodes in an X Y fashion Light is emitted when an AC voltage is applied
9. 54 00A or ordering information of el512 256 h3 frb and other EL Displays please visit http www eldisplays com el512 256 h3 frb or call 1 888 394 4998 Recommended Air Gap 8 Insert Nuts M3 Ihread Depth 2 5 mm 233 0 8 17 Fig 7 Back and Side Views Dimensions in mm 14 EL512 256 H Series Operations Manual 020 0354 00A or ordering information of el512 256 h3 frb and other EL Displays please visit http www eldisplays com el512 256 h3 frb or call 1 888 394 4998 132 5 5 22 1 5 0 08 gt 4 fastening holes M3 thread 17 0 0 67 3 2 8 Be s 5 0 0 20 2 Insert Nuts on ECA M3 thread depth 2 5 mm Dimensions in mm inches 106 0 4 17 1485 5 85 Fig 8 Back and Side Views with FRA Aluminum Mounting Frame Dimensions in mm 75 EL512 256 H Series Operations Manual 020 0354 00A or ordering information of el512 256 h3 frb and other EL Displays please visit http www eldisplays com el512 256 h3 frb or call 1 888 394 4998 10 5 4 Slots 3 5 mm width 2 Insert Nuts on ECA M3 thread depth 2 5 mm Dimensions in mm inches ee i 3 54 132 0 5 20 140 0 5 51 Fig 9 Back and Side Views with FRB Steel Mounting Frame Dimensions in mm 76 EL512 256 H Series Operations Manual 020 0354 00A or ordering information of el512 256 h3 frb and other EL Display
10. N RARO RA EN DUERME 10 Table 6 Setup and Hold Fiber ede i eH DN OR UAE OR URNA DNE A REN EORR IUE 10 Table 7 Environmental Characteristigs ooa acq Repo rq NER RU ERROR NN E ER NNI 11 Table 8 Optical Characteristics ssssssssssssssessscssssssssecssecsnecsnccssscssscessccssscesscessccsnsesnecssscsasessaeessscsnscenseeaees 12 Table 9 Display External DiMenSiOnS dio adipi RYE PR RAN ERE USER TATUR A ERES UU A TANA QU 13 Table 10 Display Viewing Area Characteristics eter eeen ennt tenen ttnnnttenntttnntis 13 or ordering information of el512 256 h3 frb and other EL Displays please visit http www eldisplays com el512 256 h3 frb or call 1 888 394 4998 Product Profile The EL512 256 H series displays are rugged high resolution electroluminescent EL flat panel displays They replace the bulky CRT in control and instrument product designs They feature an integrated DC DC converter and their compact dimensions save space that can allow addition of features or reduction in overall size They are designed to work in extreme environments and the crisp display is viewable at wide viewing angles both in horizontal and vertical directions Their ease of installation reduces system integration costs The EL512 256 H is a 512 column by 256 row flat panel display with a 1 1 pixel aspect ratio The digital flat panel interface is designed to match the needs of most systems The displays may be driven at frame rates up to
11. by Seller Buyer shall pay costs of sending Goods to Seller on a warranty claim and Seller shall pay costs of returning Goods to Buyer The turnaround time on repairs will usually be 30 working days or less Seller accepts no added liability for additional days for repair or replacement If Seller offers technical support relating to the Goods such support shall neither modify the warranty nor create an obligation of Seller Buyer is not relying on Seller s skill or judgment to select Goods for Buyer s purposes Seller s software if included with Goods is sold as is and this warranty is inapplicable to such software SELLER DISCLAIMS ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE Easy to Use There are many options available which make Planar flat panel displays easy to use easy to interface and easy to package Examples of options which are typically available include filters touch panels and interface cards Call Planar for complete information and availability 77 EL512 256 H Series Operations Manual 020 0354 00A or ordering information of el512 256 h3 frb and other EL Displays please visit http www eldisplays com el512 256 h3 frb or call 1 888 394 4998 Support and Service Planar is a US company based in Beaverton Oregon and Espoo Finland with a worldwide sales distribution network Full application engineering support and se
12. d 7 Two Bit Parallel Data 3 rase tei tree eere eia ee pendet dee E MR Urbe Ove lead ese eee deep 8 Display Enable otucaebbades tuo rata Db NIA ENDO dU E da aper abii GA eae E 8 Brightness Control aoa obaa tA Dr Ba tU AS Eo bRA RUND RARE Md Ae AC NN UR E ecd 8 kow Power MOGde ttes geo eto cete ei e thu ces eei etc ties eee A 8 SENI 8 Installation and Handling soe in e oto meni ERA pau ia e RA TS 9 Video Input TININ sso eod ain Re ee ona RR HR a ANE Ina o ien pl aa Nis 10 Setup and Hold TIMMY acute cie OR aei ORAN RR UAR eq ete RARO RA ER IRE 10 Operational Specifications isens ass ineeie ai as onina 11 Environmental uds rtt tractor ceteros S EEE E AEE S A E A E ANE e iS 11 Relia Dilhity o nad nectit based bae edo rtu re e shed met td rd oid 11 Es 11 OCI CAN rp 12 Display COLO MBPS in 12 ODT ONAL FHCOF IRE ER ERR RM RS 12 Mechanical Characteristics ssssssssssssssssssssssssssscssecsnscsnccssscsssecssccssssesscesecssscssscssscsssccessesasecssecsnecsncessscenseensessss 13 Display External DIMENSIONS aae ird ote ani crie e t ipaq ure aule a pue i Unde 13 Display Viewing Area Characteristics cese trii terti eoe angues iris ird tu 13 Descriptior ot Waltlablbyasieiope menie asete dp Dei irr na errare n erii ER N otni Rage tn eid dE 18 DIE SUI 18 S pportand Service eec cert tote icere titus E eade cicero bins rhe d euet edo ete E i E ne
13. he viewers side is input at the TVID J1 pin 7 and the data for the even columns at VID J1 pin 15 The two bit parallel mode is selected by removing jumper 2 of the pin strip PS1 Display Enable The display can be totally shut off for screen save or power reduction by a LOW sate in the ENABLE control input J2 pin 6 When disabled the display stops scanning and only the DC DC converter remains functional lowering the power consumption to below 2 W In normal operation the ENABLE input should be pulled HIGH or left disconnected internal pull up Brightness Control The brightness of the display can be adjusted appr between 40 and 100 by an external 50 k Q logarithmic potentiometer between the LUMPOT1 and LUMPOT 2 inputs J3 pins 1 and 2 The control function is done by feeding a small DC current signal via the external potentiometer from LUMPOT1 5V reference voltage to LUMPOT2 If the two inputs are left disconnected the brightness is at its maximum level Low Power Mode The power consumption of the display is possible to be reduced typically to 4 W by using the low power mode This mode is selected when LOWPOW control input J2 5 is pulled low In normal operation _LOWPOW should be pulled HIGH or left disconnected In low power mode the contrast and average brightness of the display are slightly reduced Self Test The operation of the display can be easily checked without any external signals by the self test functio
14. ing materials designed for protection of electrostatic sensitive components Warning The product generates potentially dangerous voltages capable of causing personal injury high voltage pulses up to 195 Vac Do not touch the display electronics during operation PP VS Either pulse vs polarity acceptabl n T27 i T frame n 1 HS row 256 VID TVID T4 vet T3 T4 T5 frame n frame n 1 ji row 1 T7 T6 HS i a a T8 unu X a a X4 Ju r t L ast pixel 512 256 Fig 3 Video Input Timing 8 EL512 256 H Series Operations Manual 020 0354 00A or ordering information of el512 256 h3 frb and other EL Displays please visit http www eldisplays com el512 256 h3 frb or call 1 888 394 4998 Video Input Timing Table 5 Video Input Timing Description T1 Vertical Front Porch T2 VS HIGH LOW time 2 T3 Vertical Period VS frequency Description T4 HS setup to VS T5 HS hold from VS T6 HS Low Time T7 HS High Time T8 HS period tHS Notes This time is needed to display the last row and to change the frame Only rising edge is used Video Clock VCLK should be kept running The values for two bit parallel mode are 256 256 tVCLK The number of VCLK pulses during HS high time should be even Setup and Hold Timing VS HS BLANK tSU HOLD 8ns 8ns VCLK XM m T IRE o tSU tHOLD 8 n
15. n Remove Jumper 1 in pinstrip PS1 Connect power to the display All pixels of the display will be lit with the exception of the first half of the topmost row 7 EL512 256 H Series Operations Manual 020 0354 00A or ordering information of el512 256 h3 frb and other EL Displays please visit http www eldisplays com el512 256 h3 frb or call 1 888 394 4998 Installation and Handling The product should be mounted using the M3 insert nuts on the ECA Beside the four corner nuts it is recommended to use also the two center nuts in the mounting if the vibration or shock stress is severe Before touching the display necessary precaution must be taken to prevent application of static charges on the display from the operator or tools The display is made of glass material and should be handled with proper care Do not drop the display or allow hard objects to strike its surface NOTE For trouble free data transfer a maximum cable length of 300 mm 12 in from data transmitter to display input connector is recommended If longer cables up to 2m 80 in length are needed a serial resistor of appr 47 Q could be placed at each of the four signal line outputs of the transmitter in order to lower signal reflections Electrostatic Caution Planar display use CMOS and power MOS FET devices These components are electrostatic sensitive Unpack assemble and examine this assembly in a staticcontrolled area only When shipping use pack
16. rames makes the display mounting compatible with Planar MD512 256 displays See Ordering Information on page 19 Table 9 Display External Dimensions Height 136 mm 5 35 in Width 233 mm 9 17 in Depth 16 5 mm 0 65 in Weight 400 g 14 oz Display Viewing Area Characteristics Table 10 Display Viewing Area Characteristics Active Area millimeters inches height 97 5 3 84 width 195 1 7 68 Pixel Pitch millimeters inches height 0 381 0 015 width 0 381 0 015 Pixel Size millimeters inches height 0 25 0 01 width 0 25 0 01 Pixel fill factor 43 Pixel Matrix 512 horizontal by 256 vertical CAUTION The ambient temperature of the display should not be allowed to exceed the environmental specifications see Table 7 In most applications an air gap of appr 5 mm is recommended see mechanical drawings Some applications may require however a larger air gap or cooling of the display unit in the system Note that this may slightly increase the total depth of the design 12 EL512 256 H Series Operations Manual 020 0354 00A or ordering information of el512 256 h3 frb and other EL Displays please visit http www eldisplays com el512 256 h3 frb or call 1 888 394 4998 Active Area 195 1 x 97 5 Display Glass Size 222 0 x 126 0 Fig 5 Viewing Area Characteristics CHO CK Ro Fig 6 Front View without Mounting Frame standard 73 EL512 256 H Series Operations Manual 020 03
17. rs J1 16 pin header ODU 511 066 003 016 or eq Mating ODU 517 065 003 016 or eq Locking clip ODU 511 065 716 700 or eq J2 6 pin header Hirose DF1 6P 2 5DSA or eq Mating Hirose DF1 6S 2 5 R 24 or eq Protector Hirose DF1 6A 1 33 J3 4 pin header Hirose DF1 4P 2 5DSA or eq Mating Hirose DF1 4S 2 5 R 28 or eq Protector Hirose DF1 6A 1 33 5 EL512 256 H Series Operations Manual 020 0354 00A or ordering information of el512 256 h3 frb and other EL Displays please visit http www eldisplays com el512 256 h3 frb or call 1 888 394 4998 Table 3 PS1 Position Name Function 1 SELFTST Self test function is selected if theSELFTEST jumper is OFF In self test the input video data at VID and TVID inputs are displayed asynchronously without any other input signals 2 DCONFIG The Two bits parallel mode is selectedif this jumper is OFF see page 8 3 reserved Reserved do not insert jumper 4 reserved Reserved do not insert jumper When shipped from the factory jumpers PS1 1 and 2 are set Input Specifications Table 4 Input Specifications Parameter Symbol Min Typ Max Absolute min max Logic input HIGH 2V Vcc1 0 5V abs max Logic input LOW 0 8V 0 5V abs min Logic supply voltage Vcc1 4 5V 5 0V 5 25V 6V abs max Logic supply currentat5V Icc1 0 2A Display Supply voltage Vcc2 11V 30V 33V abs max Supply current at 12V Icc2 0 5A 0 9A Supply current at 12V Icc2 0 3A 0 5A LOWPWR
18. rvice are available to make the integration of Planar displays as simple and quick as possible for our customers RMA Procedure For a Returned Material Authorization number please contact Planar Systems Inc with the model number s and original purchase order number s When returning goods for repair please include a brief description of the problem and mark the outside of the shipping container with the RMA number Ordering Information Product Description EL512 256 H2 E0051240022 0 55 C operating temperature range EL512 256 H2 FRA E0051240024 Aluminium mounting frame mounting compatible with MD512 256 37C EL512 256 H2 FRB E0051240026 Steel mounting frame mounting compatible with MD512 256 43 38 39 and EL6648MSS EL512 256 H3 996 5052 00 25 65 C operating temperature range EL512 256 H3 FRA 996 5059 00 Aluminium mounting frame mounting compatible with MD512 256 37C EL512 256 H3 FRB 996 5060 00 Steel mounting frame mounting compatible with MD512 256 43 38 39 and EL6648MSS 18 EL512 256 H Series Operations Manual 020 0354 00A or ordering information of el512 256 h3 frb and other EL Displays please visit http www eldisplays com el512 256 h3 frb or call 1 888 394 4998 Planar Systems Inc Customer Service 24x7 Online Technical Support http www planar com support Americas Support 1195 NW Compton Drive Beaverton OR 97006 1992 Tel 1 866 PLANAR1 866 752 6271 Hours M F 5am 5pm Pacific Time
19. s 8 ns tVCLK Figure 4 Setup and Hold Timing Table 6 Setup and Hold Timing Symbol Description Mn ma VCLK period VCLK frequency 30 MHz 9 EL512 256 H Series Operations Manual 020 0354 00A or ordering information of el512 256 h3 frb and other EL Displays please visit http www eldisplays com el512 256 h3 frb or call 1 888 394 4998 Operational Specifications Environmental Table 7 Environmental Characteristics Temperature Operating H2 H3 Non operating Operating Survival H2 H3 0 4 55 C 25 65 C 40 75 C 20 65 C no permanent damage 40 65 C no permanent damage Test duration 24 h at temperature extremes without condensation Humidity Relative Humidity Damp Heat 40 C 93 RH Operating IEC 68 2 3 25 55 C 95 RH Non operating IEC 68 2 30 Altitude Operating Vibration 15 000 m 50 000 ft above sea level 20 500 Hz ASD level 0 05 G Hz Random vibration wide band IEC 68 2 36 Test Fdb Shock Magnitude Duration Number of shocks 100G 4 ms half sine wave 18 3 on each of the 6 surfaces IEC 68 2 27 test Ea Reliability MTBF gt 30 000 h 25 C Safety The display will not inhibit the end product from obtaining the following specification UL544 10 EL512 256 H Series Operations Manual 020 0354 00A or ordering information of el512 256 h3 frb and other EL Displays please visit http www eldisplays com el512
20. s please visit http www eldisplays com el512 256 h3 frb or call 1 888 394 4998 Description of Warranty Seller warrants that the Goods will conform to published specifications and be free from defects in material for 12 months from delivery To the extent that Goods incorporate third party owned software Seller shall pass on Seller s licensor s warranty to Buyer subject to the terms and conditions of Seller s license Warranty repairs shall be warranted for the remainder of the original warranty period Buyer shall report defect claims in writing to Seller immediately upon discovery and in any event within the warranty period Buyer must return Goods to Seller within 30 days of Seller s receipt of a warranty claim notice and only after receiving Seller s Return Goods Authorization Seller shall at its sole option repair or replace the Goods If Goods were repaired altered or modified by persons other than Seller this warranty is void Conditions resulting from normal wear and tear and Buyer s failure to properly store install operate handle or maintain the Goods are not within this warranty Repair or replacement of Goods is Seller s sole obligation and Buyer s exclusive remedy for all claims of defects If that remedy is adjudicated insufficient Seller shall refund Buyer s paid price for the Goods and have no other liability to Buyer All warranty repairs must be performed at Seller s authorized service center using parts approved
21. za PLANAR EL512 256 H Series 512 x 256 Pixel Electroluminescent Display USER S MANUAL www planar com or ordering information of el512 256 h3 frb and other EL Displays please visit http www eldisplays com el512 256 h3 frb or call 1 888 394 4998 Revision Control Date Description April 1995 Document number PI02552 Ver 1 June 2004 Document number 020 0354 00A or ordering information of el512 256 h3 frb and other EL Displays please visit http www eldisplays com el512 256 h3 frb or call 1 888 394 4998 Contents Product Profile a ein eat a etel RR eee aer ee ER etr edd AAAI 3 EE Technology ient bate diede aM oil iui ida o NO a Post D UN o p RO aaa 3 Electrical Characteristics 5 5 e te tete recte epis tet esed teneros ev ecol N A Oin 4 Connector Eayolt ie E E re e REM Persa cies eat eat bee AAAA RANAR 4 INPUL TO THE Dis Play E 5 Control Basics 5 seca acobuaccn aaa aea aen a E E AAE vende esee ec besp cades ec cedes 6 KOAL AN SLO EE TE 6 Siga ES en E E actos coca died EE EEEE a E E ESE E 6 Optional rounding aoo teint Roe OR UR DR Ga cana ON QUANH RR EH aa GU AN UAR Gao pud 6 CONNECTOLS aae oe GERNE PIER RR RR RID RUEDA GEN I usa tim ee RE RR ER 6 Input Specifications ea a eite celi re ei tse etie a deponat tdt epus ad aae et vdd 7 Display Featil es iuda pu o TR DIR UNES HERR RNU AEN NU PRUNUS ENTRE TORTOR AE IA 7 Video Data Input 5er re tee epe ta tee oen tribue he N tuts phate ati
Download Pdf Manuals
Related Search