Home

USER`S MANUAL

1. Choose this option to select the device driver from a list Windows does not guarantee that the driver you choose will be the best match for your hardware 10 New hardware search wizard starts to search Found New Hardware Wizard Please wait while the wizard installs the software ga ISUSA USE DRIVER 2 2 z Setting a system restore point and backing up old files in case your system needs to be restored in the future USER S MANUAL 14 DSO3062L 3062AL Digital Oscilloscope 11 New hardware wizard installs software and finish new hardware search wizard Found New Hardware Wizard Completing the Found New Hardware Wizard The wizard has finished installing the software for D50 USE DRIVER 2 Click Finish to close the wizard 12 The wizard has finished installing for USB DRIVER i Found New Hardware x Your new hardware is installed and ready to use USER S MANUAL 15 DSO3062L 3062AL Digital Oscilloscope 1 4 General Features Product Features m Two Channels Bandwidth 6OMHz m Maximum real time sample rate 200MSa s m Memory depth 10K 16M CH m Automatic setup for ease of use AUTOSET Pass Fail m Built in Fast Fourier Transform function FFT 20 Automatic measurements Automatic cursor tracking measurements m Waveform storage record and replay dynamic waveforms User selectable fast offset calibration
2. Imdow Help Cascade Vertical Horizontal Arrange Icons w 1 Seopel 11 Help Turn on help file Contents Fl About FY 1 3 The Vertical System Click Setup gt Vertical DSO3062L 3062AL Digital Oscilloscope The following figure shows the vertical Setup window It shows the vertical parameters setting Fertical Setup Select Channel Channel Setting MuDFF VOLTS DI 100w Coupling 4c Probe x4 By Limit Invert USER S MANUAL 2 DSO3062L 3062AL Digital Oscilloscope 1 Select channel User can select the channel by clicking the Combo box 3 VOLTS DIV Set the selected channel voltage range VOLTS DM 1 00 4 Coupling Set the selected channel to DC AC Coupling ta 5 Probe Set the Select one according to the probe attenuation factor to ensure correct vertical scale reading Probe Fa We 7 Invert Invert the selected wave d Invert USER S MANUAL 28 DSO3062L 3062AL Digital Oscilloscope 2 4 The Horizontal System Click Setup gt Horizontal The following figure shows the Horizontal System window It shows the horizontal parameters settings Horizontal Setup Time DIY 5000us w T Format Normal Scan a Y Setting a Coordinate Y Coordinate Cancel 1 Time DIV leads the setting of the time base parameters Time DIY 50 00us 2 Format leads the setting of the horizontal format
3. Parameter Frequency Hz 0 75MHz w 035V vot T ILO 1 0 oo 10 USERS MANUAL 91 DSO3062L 3062AL Digital Oscilloscope Generate the Trapezia waveform To output a Trapezia wave please do the following steps 1 Press the check box On Off to open the wave output function 2 Select the Wave Type Trapezia Frequency Set the output wave frequency Amplitude Set the output wave amplitude Y Offset Set output wave vertical level offset Phase Set the output wave phase Duty Set the output wave duty Rise Duty Set the output wave rise duty High Duty Set the output wave high duty Fall Duty Set the output wave fall duty The Trapezia waveform window as the following Parameter Frequency 0 0 1 0 Duty Generate the Gause waveform To output a Gause Wave please do the following steps 1 Press the check box On Off to open the wave output function 2 Select the Wave Type Gause 3 Set the Wave Paramters Amplitude Set the output wave amplitude USER S MANUAL 92 DSO3062L 3062AL Digital Oscilloscope The Gause waveform window as the following Parameter Amplitude e aa Generate the Arb waveform To output an Arbitrary Waveform please do the following steps 1 Press the check box On Off to open the wave output function 2 Select the Wave Type Arb 3 Set the Wave Parameters Frequency Set the output wave frequency 4 Set
4. Measure gt Vertical gt Peak to Peak button the Vpp of the signal will also display on the bottom of the waveform interface To clear the measurement on the waveform interface click the Measure gt Clear Measure button USER S MANUAL 15 DSO3062L 3062AL Digital Oscilloscope 4 2 Pass Fail Test The Pass Fail function monitors changes of signals and outputs pass or fail signals by comparing the input signal with the pre created mask Pass Fail Control aoFF Vertical Rn i Diy Horizontal tener BE SOUrCe Stop When Output Operate Control Setting Control ONAOFF SOURCE Stop When Output Source Select the Pass Fail channel Source CH1 w Output Select the Pass Fail output condition Output FAIL s Stop When Output If it was checked the Pass Fail will stop when output Stop When Output USER S MANUAL 76 DSO3062L 3062AL Digital Oscilloscope Mask Setting Mask Vertical Set the vertical limit range Horizontal Set the horizontal limit range Horizontal 0 04 Dil Create button Click this button to create Pass Fail area according to the mask Save button Click this button to save the setups to file Save Load button Click this button to load the saved setups file Load Information Display Fail It shows the fail waveform number Pass It shows the pass waveform number Total It shows the total Pass Fail
5. Probe x 2 1 5m 1 1 10 1 Passive Probes A power adapter special for this product A USB cable A BNC to BNC A logic analyzer cable Eighteen little test hook A software installation CD USER S MANUAL 21 Chapter 2 Operating Basics The User s Interface The Menu System The Vertical System The Horizontal System The Trigger System Input Connectors USER S MANUAL DSO3062L 3062AL Digital Oscilloscope 22 DSO3062L 3062AL Digital Oscilloscope 2 1 The User s Interface Click the software icon on the desk after you finished the software setting and equipment connecting Then a user interface will be showed as follows 1413 12 11 109 In addition to displaying waveforms the display area is filled with many details about the waveform and the oscilloscope control settings 1 The Main Menu All settings can be found in the main menu 2 The Toolbar 3 It shows the trigger information It shows the edge trigger slope source and level 4 The Horizontal Panel The user can change Time Div format in the panel 5 The Vertical Panel The user can turn on off the CH1 CH2 Also the user can change the CH1 CH2 volt div coupling and probe attenuation 6 The LA Panel In this panel the user can set the LA voltage value 7 The Trigger Panel In this panel the user can change the trigger mode sweep source and slope 8 It shows the system time USER S MANUAL 23 DSO3062L 3062AL
6. 1 Source Cursor Measure Acquir Type d CH MATH The user can set the source to CH1 CH2 and MATH When you use cursors be sure to set the Source to the waveform on the display that you want to measure 2 Type cursor PO Source Cross Trace Vertical Horizontal There are four types of cursors Cross Trace Vertical and Horizontal 1 Cross The Cross cursors appear as cross lines on the display and measure the vertical and horizontal parameters USER S MANUAL 57 DSO3062L 3062AL Digital Oscilloscope The Cross cursor display window TrigD a OUST Lee ree 4 0 00uv 3454026 CH1 1 00 10 5 Time 500 0us The Cross measure result displays on status bar Freq 1 032KHz Time J69u5 Volt S08m 2 Trace The Trace cursors appear as vertical lines on the display and measure the waveform amplitude at the point the waveform crosses the cursor The Trace cursor display window TridD aL RAE tetera 0 00uv 3549752 mw 1 00V 5 Time 500 0us USER S MANUAL 58 DSO3062L 3062AL Digital Oscilloscope The Trace cursor measure result display on status bar Volt 1 957 3 Vertical The Vertical cursors appear as vertical lines on the display and measure the vertical parameters The Vertical cursor display window The Vertical cursor measure result display on status bar Freg S20 1Hz Time 1 22ms 4 Horizontal The Horizontal cursors appear as horizontal lines on the di
7. The oscilloscope continues to acquire data while waiting for the trigger condition to occur The oscilloscope continues to acquire enough data so that it can draw the waveform to the right of the trigger point after it detects a trigger The Edge trigger determines whether the oscilloscope finds the trigger point on the rising or the falling edge of a signal Select Edge trigger mode to trigger on Rising edge or Falling edge Mode Select the trigger mode Trigger Mode Sweep Set the sweep mode to Auto Normal or Single USER S MANUAL 43 DSO3062L 3062AL Digital Oscilloscope Trigger Sweep Auto Acquire waveform even no trigger occurred Normal Acquire waveform when trigger occurred Single Acquire waveform when trigger occurred then stop Source You can use the trigger source options to select the signal that the oscilloscope uses as a trigger The source can be any signal connected to a channel BNC or to the EXT BNC Trigger Source CHA CH1 Select CH1 as trigger signal CH2 Select CH2 as trigger signal EXT Select EXT as trigger signal DO D15 Select DO D15 as trigger signal Slope Set the slope to Rising or Falling Trager Sone ANN Rising Trigger on rising edge Falling Trigger on falling edge The user can also change the trigger setting on trigger panel in sidebar Trigger Trigger Mode Trigger sweep AUTO t Trigger Source CH wyt Trigger Slope Set Pulse Trigger Pulse trigg
8. The Square waveform window as the following Parameter Frequency Amplitude Y Offset Phase 00 1 0 Duty 0 04 0 Generate the AM FM waveform To output an AM FM Wave please do the following Steps 1 Press the check box On Off to open the wave output function 2 Select the Wave Type AM FM 3 Set the Wave Parameters Frequency Set the output wave frequency Amplitude Set the output wave amplitude Y Offset Set the output wave vertical level offset Phase Set the output wave phase High Frequency Set the output wave Hight Frequency Depth Set the output wave Depth Max Frequency Set the output wave Max Frequency FM Change the output wave AM into FM USER S MANUAL 90 DSO3062L 3062AL Digital Oscilloscope The AM FM waveform window as following Parameter Frequency Generate the Ramp waveform To output a Ramp Wave please do the following steps 1 Press the check box On Off to open the wave output function 2 Select the Wave Type Ramp 3 Set the Wave Parameters Frequency Set the output wave frequency Amplitude Set the output wave amplitude Y Offset Set the output wave vertical level offset Phase Set the output wave phase Duty The duty of the output wave The Ramp waveform window as the following
9. The results of the automatic measurements will be displayed on the bottom of the screen Maximum 8 results could be displayed at the same time When there is no room the next new measurement result will make the previous results moving left out of screen USER S MANUAL 63 DSO3062L 3062AL Digital Oscilloscope 3 8 The Display System Display Type Click Type in Display menu The following figure shows the type parameters setting Display w rid Ctrl g Dots Intensity If the Vectors type mode is selected the waveform will be displayed as following figure USER S MANUAL 64 DSO3062L 3062AL Digital Oscilloscope If the Dots type mode is selected the waveform will be displayed as following figure USER S MANUAL 65 DSO3062L 3062AL Digital Oscilloscope Display Grid Click Display in main menu Display w Grid Ctrl g Dots Intensity The grid shows Trig D dhe DWAAAARAAAAAAA 0 00uv mw 1 00V 15 Time 500 0us The grid not shows TrigD T j l 0 00uV CH1 ny 10 6 Time 500 0us USER S MANUAL 66 DSO3062L 3062AL Digital Oscilloscope Intensity and Persistence Click Display gt Intensity in main menu The following figure shows the intensity dialog It shows the display parameters setting Intensity Setting rid f Scale Waveform You can change the grid and waveform color intensity in this dialog USER S MANUAL 67 DSO3062L 3062
10. All Terminal Ratings To avoid fire or shock hazard observe all ratings and markings on the product Consult the product manual for further ratings information before making connections to the product m Use Proper Probe To avoid shock hazard use a properly rated probe for your measurement m Avoid Circuit or Wire Exposure Do not touch exposed connections and components when power is on m Do Not Operate With Suspected Failures If suspected damage occurs with the device have it inspected by qualified service personnel before further operations m Provide Proper Ventilation Refer to the installation instructions for proper ventilation of the device Do not operate in Wet Damp Conditions Do not operate in an Explosive Atmosphere m Keep Product Surfaces Clean and Dry USER S MANUAL 3 DSO3062L 3062AL Digital Oscilloscope Chapter 1 Getting Start The oscilloscope is small lightweight no external power required portable oscilloscopes The oscilloscopes is ideal for production test research and design and all of the applications involving analog circuits test and troubleshooting as well as education and training In addition to the list of general features on the next page this chapter describes how to do the following tasks m System Requirements m Install your product General Features m General Check m Perform a probe check and compensate probes m Match your probe attenuation factor m Use the self ca
11. B Source A and Source B Menu Operate Four Types A B Add source A and source B A B Subtract source B from source A AxB Multiply source A by source B A B Divide source A by source B FFT Convert a time domain signal into its frequency components spectrum In this function use the addition subtraction multiplication and FFT function to operate and analyze the waveform USER S MANUAL 37 DSO3062L 3062AL Digital Oscilloscope Select the operate type in the Operate menu Select source A and B Then adjust the vertical scale and offset to view the math channel clearly The mathematic result can be measured by the measure and the cursor The Math Function Display PR pt 1 Invert The invert function turns the displayed waveform 180 degrees with respect to the ground level When the oscilloscope is triggered on the inverted signal the trigger is also inverted Click Invert in MATH invert USER S MANUAL 38 The following picture shows the waveform before inversion Trig D Ae nu 10 0 The following picture shows the waveform of inversion TridD aie fy 10 0 USER S MANUAL DSO3062L 3062AL Digital Oscilloscope 0 00UW 2324326 Time 500 0us 0 00uVw 2402522 Time 500 0us 39 DSO3062L 3062AL Digital Oscilloscope Set Reference Click REF in Setup menu to s
12. Digital Oscilloscope 9 Marker shows Edge trigger level 10 It shows the main time base setting 11 It shows the LA channel setting on off status 12 It shows the CH2 information Readouts show the coupling of the channels Readouts show the vertical scale factors of the channels A B icon indicates that the channel is bandwidth limited 13 It shows the CH1 information Readouts show the coupling of the channels Readouts show the vertical scale factors of the channels A B icon indicates that the channel is bandwidth limited 14 It shows the software status 15 The markers show the LA reference points of the displayed waveforms If there is no marker the channel is not displayed 16 The markers show the CH2 reference points of the displayed waveforms If there is no marker the channel is not displayed 17 The markers show the CH1reference points of the displayed waveforms If there is no marker the channel is not displayed 18 A window that shows the display waveform in buffer position 19 The LA Bus 20 Marker shows horizontal trigger position 21 Trigger status indicates the following AUTO The oscilloscope is in auto mode and is acquiring waveforms in the absence of triggers Trig D The oscilloscope has seen a trigger and is acquiring the post trigger data WAIT All pretrigger data has been acquired and the oscilloscope is ready to accept a trigger STOP The oscilloscope has stopped acqui
13. The oscilloscope recalls this setup the next time you run the software You can use the Save Setup menu to permanently save up to several different setups Load Setup The oscilloscope can recall the last setup before the oscilloscope software was running any saved setups or the factory setup You can use the Load Setup menu to permanently recall a setup Factory Setup The oscilloscope software is set up for normal operation when it is shipped from the factory This is the factory setup To recall this setup push the Factory Setup menu USER S MANUAL 34 DSO3062L 3062AL Digital Oscilloscope 3 2 Set Vertical System Set Channel Click Vertical in Setup menu The Channel Selection Select Channel CH yt The Channel Control Panel in sidebar Vertical The Vertical function Turn ON Off Turn on off the channel VoIt DIV Select the channel voltage div Coupling Select the channel coupling Probe Select the channel probe attenuation Invert Turn on off the invert function Change Volt DIV You can click voltDiv in vertical Setup window to select the voltage VOLTS DM 1 00 You can also change the selected channel voltage in sidebar Vertical CH1 e ONOFF 00v r Je 4 T USER S MANUAL 35 DSO3062L 3062AL Digital Oscilloscope You can left click and drag the mouse on the knob to change the voltage Set Channel Coupling Click Coupling in Ve
14. Type Set the Trigger Type to Edge or Pulse USER S MANUAL 46 DSO3062L 3062AL Digital Oscilloscope Trigger Type PW Condition Set the PW Condition to the following condition More Pulse width more than selecting pulse condition Less Pulse width less than selecting pulse condition Equal Pulse width equal to selecting pulse condition More Pulse width more than selecting pulse condition Less Pulse width less than selecting pulse condition Equal Pulse width equal to selecting pulse condition Pulse Width The Pulse Width adjust range is 10ns 10s When the condition is met it will trigger and acquire the waveform Pulse Fidth Setting n hal The user can also change the trigger setting on trigger panel in sidebar Trigger Trigger Mode ALT Trigger Channel CH1 wt Trigger Type Pulse wt PYY Condition Less Pulse Vyictth 10 0ne Halal USER S MANUAL 47 DSO3062L 3062AL Digital Oscilloscope 2 Set Bus Trigger The Bus mode includes three trigger modes Trigger value Trigger at the appearance of a specified value on the selected bus Duration Trigger at x time after the appearance of a specified value Edge Trigger at the appearance of a specified value on the selected bus and rising falling or rising edge of the selected signal Trigger Setup Single Bus Advanced setting Trigger Mode Trigger Value 3 Setup Advanced Trigger If the basic trigger can t
15. meet your requirement you need the advanced trigger setup Trigger Setup Single Us Advanced Data Min lo Data Duration Min joins Time Max jo xin F Edge SOUrce Slope d Relative Trigger USER S MANUAL 48 DSO3062L 3062AL Digital Oscilloscope There are four parts in the conditions Data Duration Edge and Relative trigger High Frequency Rejection Select HF Rejection in Trigger Setup window Trigger Setup single Bus Advanced setting Trigger Mode Ede Trigger Sweep AUTO Trigger Source CHi Trigger Slope The user can turn on HF Rejection to eliminate trigger higher frequency 20M above USER S MANUAL 49 3 5 Save Load Save Click File in main menu to save waveform setups and screen eR View Setup Display Hew Ctrlti Close Load Data CtrltL Load Setup cave Data Ctrlts nave Setup Save mage Print CtrltF Print Preview Print Option Connect Exit 1 Save Data Save waveform data as a type file 2 Save Setup Save the current oscilloscope setup to file 3 Save Image Save the software display window as a bmp or jpg file Load Click File in main menu to recall saved waveform setup 1 Load Data Load the waveform that had saved as a type file 2 Load Setup Load the instrument that had saved USER S MANUAL DSO3062L 3062AL Digital Oscilloscope 50 DSO3062L 306
16. waveform It can stop playing back if you started playing back Start button Click this button to start a record setup Start Note When it plays back waveform the other channel will be turned off USER S MANUAL 52 DSO3062L 3062AL Digital Oscilloscope Pass Fail Click Pass Fail in Utility menu Record Pass Fail FC d Calibration Factory Setup Language d The Pass Fail window appears Pass Fail Control ON OFF l _ L Vertical We EB Diy SOUrce 2a Horizontal anwar BE Diy Load Operate The Pass Fail function monitors changes of signals and outputs pass or fail signals by comparing the input signal with the pre created mask Control Setting Control ONOFF SOURCE Output v Stop When Output Source Select the Pass Fail channel Source CH1 ka Output Select the Pass Fail output condition USER S MANUAL 53 DSO3062L 3062AL Digital Oscilloscope Stop When Output If it was checked the Pass Fail will stop when output Stop When Output Mask Setting Mask Vertical Set the vertical limit range Horizontal Set the horizontal limit range Create button Click this button to create Pass Fail area according to the mask Create Save button Click this button to save the setups to file Save Load button Click this button to load the saved setups file Load Information Display Fail It shows the fail waveform
17. 2AL Digital Oscilloscope 3 6 Utility Function Record and Play Back Click Record in Utility menu Utility Vehicle W Record Pass Fail FC d Calibration Factory Setup Language d The Record window will display The following picture shows the Record Interface Record And Play Hack Record Setup SOURCE End Frame Record Play Back Setup Start Frame End Frame Current Frame This function can record input waveform form CH1 CH2 The maximum record length is 1000 frames Record Setup window Record Setup End Frame 1 000 Record j 4 Source Select record source channel CH1 CH2 USER S MANUAL 51 DSO3062L 3062AL Digital Oscilloscope End Frame Set the number of record times The max frames are 1000 End Frame 1000 Record Record counter it shows the record frames Record j Start button Start to record frames After you start to record waveforms this button changes to Stop button It stops recording waveforms Play back setup window Play Back Setup Start Frame End Frame 1000 Current Frame Start Frame Set the start frame of play back Start Frame r End Frame Set the end frame of play back End Frame 1000 2 Current Frame It shows the current frame of play back You can also change this number to watch the waveform one by one Current Frame 1 Play button Click this button to start playing back
18. AL Digital Oscilloscope 3 9 Zoom In Out and Drag Waveforms The software will stop updating waveform after the user clicked Stop button The user can change the waveform display by adjusting the scale and position When you change the scale the waveform display will increase or decrease in size When you change the position the waveform will move up down right or left The channel reference indicator identifies each waveform on the display The indicator points to the reference level of the waveform record ee Vee w Eun Ctrltk Stop Ctrlto Butfer Length d Acquisition d Interpolation d Autoset Zoom In Out The user can click Zoom In Out in Acquire menu then left or right click the mouse button on display screen to zoom in out the waveform Also the user can change Time Div in Horizontal menu or in Horizontal panel to zoom in out the waveform Drag The user can modify the waveform position after clicked Drag in Acquire menu following the following steps Drag Waveforn Operation Memory Data Length 10240 Move Step 1000 USER S MANUAL 68 DSO3062L 3062AL Digital Oscilloscope 1 Select Channel CH1 k 2 Set the Move Step Move Step 1000 3 Change the waveform position USER S MANUAL 69 DSO3062L 3062AL Digital Oscilloscope 3 10 Interpolation At the time base 40ns div or faster user can use the 3 different interpolation mode to get waveforms of differe
19. Add Subtract and Multiply Mathematic Functions Selectable 20 MHz bandwidth limit m External trigger m Waveform average m Adjustable waveform intensity more effective waveform view m User interface in several user selectable languages USER S MANUAL 16 DSO3062L 3062AL Digital Oscilloscope 1 5 General Check Please check the instrument as following steps after receiving an oscilloscope Check the shipping container for damage Keep the damaged shipping container or cushioning material until the contents of the shipment have been checked for completeness and the instrument has been checked mechanically and electrically Check the accessories Accessories supplied with the instrument are listed in Accessories in this guide If the contents are incomplete or damaged please notify the franchiser Check the instrument In case there is any mechanical damage or defect or the instrument does not operate properly or fails performance tests please notify the franchiser Probe Compensation Perform this function to match the characteristics of the probe and the channel input This should be performed whenever attaching a probe to any input channel at the first time m From the Probe menu select attenuation to 1 10 Set the switch to X10 on the probe and connect it to CH1 of the oscilloscope When using the probe hook tip insert the tip onto the probe firmly to ensure a proper connection m Attach the pro
20. Condition Less Pulse width less than selecting pulse condition Equal Pulse width equal than selecting pulse condition More Pulse width more than selecting pulse condition Set Pulse Width highlighted including Time Unit and PASE aR o Pulse Width USER S MANUAL 45 DSO3062L 3062AL Digital Oscilloscope Video Trigger Mode Select the trigger mode Trigger Mode Video Sweep Trigger Sweep AUTO yt Source Set the Trigger Channel to CH1 CH2 Trigger Channel Trigger Sync Trigger Syne All Lines i Trigger Standard Standard Pay Sec Ww m With Video highlighted an NTSC PAL or SECAM Video standard video signal will be triggered The trigger coupling is preset to AC Auto Acquire waveform even no trigger occurred Sweep Normal Acquire waveform when trigger occurred Single Acquire waveform when trigger occurred then stop CH1 Select the input source as the trigger signal Ext use Source CH2 the signal applied to the EXT TRIG connector as the EXT source All Lines Line Number Choose a proper video sync When selecting Line sync Odd Field Number for the Sync option you may use the User Even Field Select knob to specify a line number All Fields Standard NTSC Choose a video standard for sync and line number PAL SECAM count Set ALT System Mode Select the trigger mode Trigger Mode p30 i Trigger Channel Set the Trigger Channel to CH1 CH2 Trigger Channel Trigger
21. Connector CH1 CH2 Input connectors for waveform display EXT Input connector for an external trigger source Use the Trigger Menu to select the Ext Source Other Connector OUTPUT Signal output GND a ground terminal USB PORT Connect the USB cable to this port 10 115 The LA input data channels CAL Probe compensation output GPower Power Input port USER S MANUAL 32 DSO3062L 3062AL Digital Oscilloscope Chapter 3 Oscilloscope Functions Set Oscilloscope Set Vertical System Set Horizontal System Set Trigger System Save Load Utility Function Measure Signal Zoom In Out Waveforms Acquire Signal Print USER S MANUAL 33 DSO3062L 3062AL Digital Oscilloscope 3 1 Setup the Oscilloscope Using AUOSET to display a signal automatically Auto setup functions one time each time you push the AUTOSET button The function obtains a stable waveform display for you It automatically adjusts the vertical scale horizontal scale and trigger settings Auto setup also displays several automatic measurements in the graticule area depending on the signal type Connect a signal to the CH1 input 1 Connect a signal to the oscilloscope as described above 2 Click the Acquire gt Autoset button The oscilloscope will change the current settings to display this signal Save Setup The oscilloscope software saves the current setup before you close the oscilloscope software
22. Digital Oscilloscope 1 Click Print in File menu to set the printer to print the current waveform 2 Click the PrintPreview in File menu to get into the Preview window In PrintPreview window use the Zoom In button and the Zoom Out button to change the size of the waveform graph Click the Close button to turn this window off and click the Print button to print the report The Print report Test Report DSO 3062AL USB Date 0208 2012 Time 11 20 35 USER S MANUAL 13 DSO3062L 3062AL Digital Oscilloscope Chapter 4 Application Example Sample Measurement Pass Fail Test Capturing a Single Shot Signal The Application of the X Y Taking Cursor Measurement Arbitrary Waveform Generator USER S MANUAL 74 DSO3062L 3062AL Digital Oscilloscope 4 1 Simple Measurement To acquire and display a signal please do the steps as follows 1 Connect signal to CH1 by using probe 2 Click the button on toolbar or Acquire gt Auto Setup on menu The DSO set the vertical horizontal and triggers controls at the best status automatically Also you can adjust the controls to meet your measurement to optimize the waveform display To measure the frequency and Vpp you can do these steps as follows 1 Click the Measure gt Horizontal gt Frequency button the frequency of the signal display on the bottom of the waveform interface 2 Click the
23. E dade datecode E 76 4 3 Capturing a Single Shot Signal ccccccssscccccssseecceseeeceeseeeceeseeecsegsesessaseeesssaseees 19 4 4 The Application of the X Y Operation pp 80 4 5 Taking Cursor Measurements pp 82 A OO Cay Ze lk T arate rtadatadata data dastadatatatadatadaia setae laden datadaadan ducha dada dahe tuchadeaat 85 4A Navel orm Generato nae 88 Chapter 5 ADDendix cccecccceececeeceeeeeeeceeceeseeeeeeserseseeeeeataeeees 96 Appendix A Specifications pp 97 APPEnNdIX B ACCOSSONGCS orinn a S 100 Appendix C General Maintenance pp 102 DSO3062L 3062AL Digital Oscilloscope General Safety Summary Review the following safety precautions carefully before operate the device to avoid any personal injuries or damages to the device and any products connected to it To avoid potential hazards use the device as specified by this user s guide only To Avoid Fire or Personal Injury m Use Proper Power Cord Use only the power cord specified for this product and certified for the country of use m Connect and Disconnect Properly Do not connect or disconnect probes or test leads while they are connected to a voltage source Connect and Disconnect Properly Connect the probe output to the measurement device before connecting the probe to the circuit under test Disconnect the probe input and the probe reference lead from the circuit under test before disconnecting the probe from the measurement device m Observe
24. Hantek USER S MANUAL DSO3062L DSO3062AL http www hantek com Content General Safety Summary pp 3 Chapter 1 Getting ae 4 TU SV SCOT AR OCIS men eras ae ee eee 5 1 2 Install Software 4 6 NS 10 eneIeEea Sa 16 oe Cre ale i CNECK camer teen eee arta eee oe ere eee ae ce ee ee a ee te ae eee ee nee ete ene eee ee eee ener 17 Me Oe CMON IL OGA acetate ea eacaciecediederiodamededaderiededenedadecedaderedadediededietedadediadedatedadedndadadead 19 20 WeAocsssones a Senn Goo adane EEE EEE EE EAEE EEEE ES 21 Chapter 2 Operating Basics pp 22 a Ws Bt gy eh WW Ke excel goles CE 23 2 2 TNE Menu System 4 25 to WUT vencal SY SUTIN anni narnia ernie leneiaainitiaie 27 2 4 The Horizontal System pp 29 ASe Tigger SY SION ee eae 30 ZONA CN ORI O head ace cen NENN 32 Chapter 3 Oscilloscope Functions pp 33 321 SelUD Ne OSCIIIOSCODE ksnar E 34 3 2 Set Vertical System 35 Oo TU AOFIZ OR Vaal SVS COU a 41 3 4 Set Trigger System 4 43 OS OIC ease eee E E S A A A E E 50 SOUU EGG 51 OE ISAS US SONA acta eae teen eae nae aaa maa 57 3 9 The Display Syste eee sire tate sented seteediavede setoadeaniedia aa aai 64 3 9 ZOOM INOUE and Drag WavefonMNS esser eee det Seeded 68 70 Ol ACOUISHHOM MORG S Acciona Kae eae es ee ee 72 912 PIMAN TING PTO VICW isisao n O E 72 Chapter 4 Application Example pp 14 AA Simple MeasuUremienle 222 cess aia aaa Sieadio aera acd eta aaa rd aid ener a 15 AZ FoS F AN WS Ste ae ese ec A
25. Hardware Wizard Please wait while the wizard installs the software DS0 a USE DRIVER 1 DSio l SYS To CAWIN DOW S Systens2 Drivers 7 Finish new hardware search wizard Found New Hardware Wizard Completing the Found New Hardware Wizard The wizard has finished installing the software for DS0 W USE DRIVER 1 Click Finish to close the wizard USER S MANUAL Lancel ape e ale Lance DSO3062L 3062AL Digital Oscilloscope 8 New hardware is found i Found New Hardware x DS0 xxxx USB DRIVER 2 This wizard helps vou install software for DSO USE DRIVER 2 If your hardware came with an installation CD LEA or floppy disk insert it now What do vou want the wizard to do Install the software automatically Recommended O Install from a list or specific location Advanced Click Next to continue USER S MANUAL 13 DSO3062L 3062AL Digital Oscilloscope 9 Set the driver search location to CD Rom or the driver path Found New Hardware Wizard Please choose your search and installation options eS Search for the best driver in these locations Use the check boses below to limit or expand the default search which eludes local paths and removable media The best driver found will be metalled Search removable media floppy CD ROM Include this location in the search Don t search will choose the driver to install
26. Setup Status DS0 30624L USE is configuning your new software installation InstallShield T The installation is complete DS0 3062AL USB InstallShield Wizard InstallShield Wizard Complete Setup has finished installing OS0 30624L USE on pour Computer _ Finish I Cancel USER S MANUAL 9 DSO3062L 3062AL Digital Oscilloscope 1 3 Install Driver Example DSO3062AL 1 Connect the A Type Plug of USB cable to your PC s USB port 3 New hardware is found i Found New Hardware x IS0 xxxx USB DRIVER 1 USER S MANUAL 10 DSO3062L 3062AL Digital Oscilloscope 4 New hardware search wizard starts Found New Hardware Wizard This wizard helps you install software for DSO USE DRIVER 1 If your hardware came with an installation CD lt 4 or floppy disk insert it now What do vou want the wizard to da Install the software automatically Recommended O Install from a list or specific location Advanced Click Next to continue 5 New hardware search wizard starts to search the driver Found New Hardware Wizard Please wait while the wizard installs the software ga ISOTA USE DRIVER 1 2 Setting a system restore point and backing up old files in case Your system needs to be restored in the future USER S MANUAL 11 DSO3062L 3062AL Digital Oscilloscope 6 New hardware wizard installs USB DRIVER Found New
27. The LA BUS reference points of the displayed waveforms Display Style You can set the display style of the bus in the waveform Analog or Digital USER S MANUAL 85 DSO3062L 3062AL Digital Oscilloscope Analog prt rre ttre rrr preter rrr yrrrrprrr rye rrrprr rrr rT Digital Display Format The format of the bus data displayed on the waveform Click Setup gt Bus gt Data E hislar Cursor Meas REF Ctrltk MATH Ctrl M Trigger CtrltT Vertical Ctrlty Horizontal CtrltH Trigger Release Ctrlth mE Logic Calibrate s Hex Hex Decimal USER S MANUAL 86 DSO3062L 3062AL Digital Oscilloscope Plug in I7C Click Setup gt Plug in Select the plug in and click the Set button you can set up the configurations of the plug in USER S MANUAL 87 DSO3062L 3062AL Digital Oscilloscope 4 7 Waveform Generator Caution This part is only used for DSO3062AL DSO 3062AL can also be used as the Arbitrary Waveform Generator with one channel of arbitrary waveform output 8 Bits output synchronized signal out puts User can edit the waveform arbitrary by the mouse or choose the regular waveforms such as Sine Square AM FM Ramp Trapezia Gause Arb Exponent White Select the DDS control panel in the sidebar pso DDS Jonot Syne Single Wave Type O sine C SQUare CANE NM OQ Ramp Trapezia CO GAUZE CO Arkh f Exponent White Param
28. all power sources To clean the exterior surface perform the following steps 1 Remove loose dust on the outside of the oscilloscope and probes with a lint free cloth Use care to avoid scratching the clear glass display filter 2 Use a soft cloth dampened with water to clean the device USER S MANUAL 102
29. be tip to the Probe Compensator and the reference lead to the ground connector select CH1 and then press the AUTOSET button into the menu or the toolbar m Check the shape of the displayed waveform Correctly Compensated USER S MANUAL 17 DSO3062L 3062AL Digital Oscilloscope Over Compensated Under Compensated 1 If necessary use a non metallic tool to adjust the trimmer capacitor of the probe for the fattest square wave being displayed on the oscilloscope 2 Repeat if necessary WARNNING To avoid electric shock while using the probe be sure the perfection of the insulated cable and do not touch the metallic portions of the probe head while it is connected with a voltage source USER S MANUAL 18 DSO3062L 3062AL Digital Oscilloscope 1 6 Function Check Perform this functional check to verify that your oscilloscope is operating correctly m Connect the oscilloscope You should connect the A Type Plug of USB cable to your PC USB port and connect the other A Type Plug of USB cable to oscilloscope USB port m Input a signal to a channel of the oscilloscope The oscilloscope is equipped with two channels plus external trigger Please input signal in the following steps 1 Set the attenuation switch on the probe as 10X and connect the probe on the oscilloscope with CH1 Aim the slot in the probe connector at the faucet on BNC of CH1 and insert then turn right to lock the probe Finally attach the tip of
30. ed Time Div control expands or compresses the waveform USER S MANUAL 41 DSO3062L 3062AL Digital Oscilloscope Change Format Click Time Div you can Set the Time base in Horizontal Setup window Time olw 5000us 4 In the Format item set the waveform display format Y T X Y Y T Show the relative relation between vertical voltage and horizontal time X Y Show CH1 value at X axis CH2 value at Y axis Change Horizontal Position Double click the channel button to set the trigger point to the horizontal center of the screen Horizontal position changes the displayed waveform position relative to the trigger point The user can drag LA on screen to change the horizontal position USER S MANUAL 42 DSO3062L 3062AL Digital Oscilloscope 3 4 Set Trigger System Click Setup gt Trigger you can configure the trigger The user can also click T in the toolbar to set Trigger 1 Set Single Trigger Trigger Setup ingle Bus Advanced Setting Trigger Mode Edge Trigger Sweep AUTO Trigger Source CH1 Trigger Slope HF Rejection Edge Trigger The trigger determines when the oscilloscope starts to acquire data and display a wave form When a trigger is set up properly it can convert unstable displays or blank screens into meaningful waveforms If the oscilloscope wants to acquire a waveform it collects enough data so that it can draw the waveform to the left of the trigger point
31. er occurs according to the width of pulse The abnormal signals can be detected through setting up the pulse width condition Trigger Mode Mode Trigger Sweep Sweep Trigger Source CHi hgt Source USER S MANUAL 44 DSO3062L 3062AL Digital Oscilloscope PW Condition Less a Pulse Width The Pulse Width adjust range is 10ns 10s When the condition is met it will trigger and acquire the waveform Pulse Width Setting Time Units ns The user can also change the trigger setting on trigger panel in sidebar Trigger Trigger Mode Pulse t Trigger Sweep AUTO wt Trigger Source CH1 w Puy condition Less Pulse Width When alternative trigger is on the trigger sources come from two vertical channels This mode can be used to observe two non related signals You can choose two different trigger modes for the four vertical channels With Pulse highlighted the trigger occurs on pulses that Pulse meet the trigger condition defined by the Source When and Set Pulse Width options Auto Auto Acquire waveform even no trigger occurred Sweep Normal Normal Acquire waveform when trigger occurred Single Single Acquire waveform when trigger occurred then stop CH1 CH2 Select the input source as the trigger signal EXT Less Pulse width less than selecting pulse condition Equal Pulse width equal than selecting pulse condition PW More Pulse width more than selecting pulse condition
32. eshold range Max Sample Rate Bandwidth Compatible input Storage depth Waveform Frequency A Frequency Resolution O Channel Waveform Depth Vertical Resolution Frequency Stability Wave Amplitude Output Impedance O1 Output Current 50mA lpeak 50mA system BW 25M Harmonic Distortion 50dBc 1KHz 40dBc 10KHz Current Range CC65 20A CC65 60A CC650 CC 1100 Cursor Time frequency difference voltage difference USER S MANUAL 99 DSO3062L 3062AL Digital Oscilloscope 8 36V Wide range of input voltage Power Source i suitable for vehicle power test 255 x 190 x 45 mm Weight Appendix B Accessories DSO3062L Accessories X1 X10 two passive probes The passive probes have a 6MHz bandwidth rated 100Vrms CAT III when the switch is in the X1 position and a maximum bandwidth rated 300Vrms CAT II when the switch is in the X10 position Each probe consists of all necessary fittings A power adapter special for this product In addition to the power adapter shipped with your instrument you may purchase another one certified for the country of use A USB line used to connect external devices with USB interface like a printer or to establish communications between PC and the oscilloscope A 20 pin logic analyzer exhaust line ARAARI fit Eighteen little test hook HT321 Logic analyzer with high quality test hook T R A software installation CD and it contains the user manual for the oscillosc
33. et REF channel J OMOFF wolt d Diy Time ylw 50 00us Drag Ref DataLen O Move Step 1000 The Reference Channel Function On Off Turn on off the reference channel Volt DIV Channel the resolution of the reference channel Load Load the reference waveform from the rfc file from your computer Save Save the current reference waveform to your computer as rfc format Save Reference Save the current reference waveform to your computer as rfc format You can change the vertical scale of a waveform The waveform display will contract or expand relative to the reference level Load Click Load to load the rfc file that was selected The load file window will appear Save Click Save to save the waveform to rfc file The saved source window appears Select a channel The save file window will appear after you selected the saved source USER S MANUAL 40 DSO3062L 3062AL Digital Oscilloscope The Reference Waveform Display Window i Note If you turn on the Reference channel the load file window will appear 3 3 Setup Horizontal System Change Time Div The Time Div SO 00us Selects the horizontal Time DIV scale factor for the main or the window time base Time t Dry The Horizontal Panel Horizontal Time t DI 50 004 v Click the blue knob can change Time Div If the waveform acquisition is stopp
34. eter Frequency Hz 0 7S5MHZ Amplitude Y O35 WoT ow PM A Click any button of certain waveform to switch to the output of such kinds of waveform O 0 1 0 The user can select wave type as below Wave Type O sine SQUare CO AMF M Ramp O Trapezia O GAUSE O Ark Exponent White USER S MANUAL 88 DSO3062L 3062AL Digital Oscilloscope Waveform Parameter Setup Select a wave type and you can set the Parameters in the sidebar Generate the Sine waveform To output a Sine Wave please do the following steps 1 Press the check box On Off to open the wave output function 2 Select the Wave Type Sine Wave 3 Set the Wave Parameter Frequency Set the output wave frequency Sweep Set the output wave to sweep Amplitude Set the output wave amplitude Y Offset Set the output wave vertical level offset Phase Set the output wave phase The Sine waveform window as the following Parameter Frequency Generate the Square waveform To output a Square Wave please do the following Step 1 Press the check box On Off to open the wave output function 2 Select the Wave Type Square 3 Set the Wave Parameters Frequency Set the output wave frequency Amplitude Set the output wave amplitude Y Offset Set the output wave vertical level offset Phase Set the output wave phase Duty Set the duty of the output wave USER S MANUAL 89 DSO3062L 3062AL Digital Oscilloscope
35. lShield Wizard will install OSO 30624L USB on your computer To continue click Mest DSO S3062AL USE InstallShield Wizard Customer Information Please enter your infosmation User Name Microsoft Users Microszott Users Install this apphcabon for Anyone who uses this computer all users O Only for me Microsoft Users Install hield USER S MANUAL DSO3062L 3062AL Digital Oscilloscope 4 Choose a Setup Type directory Click Next to continue DSO 30627AL USB InstallShield Wizard Setup Type Select the setup type to mstall Click the type of setup you prefer then click Next Typical Program vall be installed with the most common options Recommended for most users Program vall be installed vaith minimum required options fou may select the options you want to install Recommended fo advanced UEIS 5 Check the setup information Click Next to start copying of Files DSO 30627AL USB InstallShield Wizard Start Copying Files Review settings before copying files Setup has enough infomation to start copying the program files If you want bo review or change any settings click Back If pou are satshed with the settings cick Next to begin copying files Current Settings USER S MANUAL 8 DSO3062L 3062AL Digital Oscilloscope 6 This Status dialog is displayed during copying of Files DSO S067AL USB InstallShield Wizard
36. le if you generated an 1 KHz sine waveform you will also generate an 1 KHz square waveform simultaneously The software setting is following figure Sine Frequency 1000 000 Hz V Pk to Pk 4 000 Y The waveform on CH1 is the sine waveform you generated from the OUTPUT terminal and that on CH2 is the synchronized signal from SYNC OUT terminal USER S MANUAL 95 DSO3062L 3062AL Digital Oscilloscope Chapter 5 Appendix Appendix A Specifications Appendix B General Maintenance USER S MANUAL 96 DSO3062L 3062AL Digital Oscilloscope Appendix A Specifications Specifications Table DSO3062L Vertical Analog Channels Bandwidth Rise Time 60MHz 3dB 5 8ns Resistance 1MQ Capacitance 25 pF 10mV div to 5V div AC DC GND 8 bits 10K 16M CH 400V DC AC Peak Input Impedance Input Sensitivity Input Coupling Vertical Resolution Memory Depth Maximum Input Real Time Sampling Rate eee Time Base Range ons div to 1000s div 1 2 5 sequences Time Base Precision 50ppm Trigger Source Mode X Y mode X Axis Input CH1 CH2 D0 D15 EXT Edge Pulse Video Alternative L L N Y Axis Input Phrase Shift Cursors and Measurement Max 3 degree Vpp Vamp Vmax Vmin Vtop Vmid Vbase Vavg Voltage Measurement Vrms Vcrms Preshoot Overshoot Frequency Period Rise Time Fall Time Positive Width Negative Width Duty Cycle USER S MANUAL 97 Time Measu
37. libration routine m Accessories USER S MANUAL 4 DSO3062L 3062AL Digital Oscilloscope 1 1 System Requirement To run the oscilloscope software the needs of computer configuration are as follows Minimum System Requirements Operating System Window XP VISTA Win7 Processor Upwards of 1 00G processor Memory 206M byte Disk Space 500M disk free space Screen resolution 800 x 600 Recommended Configuration Operating System Windows XP SP3 System Processor 2 4G Processor Memory 1G Byte Memory Disk Space 80G Disk Space Screen resolution 1024 x 768 or 1280 x 1024 resolution DPI Setting Normal Size 96DPI USER S MANUAL 5 DSO3062L 3062AL Digital Oscilloscope 1 2 Install Software Caution You must install the software before using the oscilloscope 1 While in Windows insert the installation CD into the CD ROM drive 2 The installation should start up automatically Otherwise in Windows Explorer switch to the CD ROM drive and run Setup exe InstallShield Wizard Preparing to Install O50 30624L USB Setup is preparing the Installshield Wizard which will guide you through the program setup process Please wait Preparing to Install Cancel USER S MANUAL 6 DSO3062L 3062AL Digital Oscilloscope 3 The software Installation is started Click Next to continue DS0 30624L USB InstallShield Wizard Welcome to the InstallShield Wizard for DSO 30624L USE The Instal
38. n The arithmetic mean over the entire waveform Cycle Mean The arithmetic mean over the first cycle in the waveform Preshoot Positive Overshoot Max Top Amp x 100 Measured over the entire waveform Overshoot Negative Overshoot Base Min Amp x 100 Measured over the entire waveform USER S MANUAL 61 DSO3062L 3062AL Digital Oscilloscope 3 Horizontal Measure Aequire Utility Source Vertical Horizontal Period Clear Measure CtrltM Frequency Rise Time Fall Time Duty Cycle Duty Cycle Pulse Width Pulse Width Period Time to take for the first signal cycle to complete in the waveform Frequency Reciprocal of the period of the first cycle to complete in the waveform Rise Time Time taken from lower threshold to upper threshold Fall Time Time taken from upper threshold to lower threshold Duty Cycle Positive Duty Cycle Positive Pulse Width Period x 100 Measured of the first cycle in waveform Duty Cycle Negative Duty Cycle Negative Pulse Width Period x 100 Measured of the first waveform Pulse Width Measured of the first positive pulse in the waveform The time between the 50 amplitude points Pulse Width Measured of the first negative pulse in the waveform The time between the 50 amplitude points USER S MANUAL 62 DSO3062L 3062AL Digital Oscilloscope 4 Clear Measure Clear all measure items on display screen The Measure Display Window Note
39. nt smoothness The Step Interpolation The Linear Interpolation USER S MANUAL 70 DSO3062L 3062AL Digital Oscilloscope The Sin x x Interpolation Note The default interpolation mode is Sin x x Acquisition When you acquire a signal the oscilloscope converts it into a digital form and displays a waveform The acquisition mode defines how the signal is digitized and the time base setting affects the time span and level of detail in the acquisition USER S MANUAL 71 DSO3062L 3062AL Digital Oscilloscope 3 11 Acquisition Modes There are two acquisition modes Normal Average and Peak Detect w Kun Ctrl k Stop Ctrlto Buffer Length d Acquisition Interpolation d Ayer age d Feak Detect Autoaset Normal In this acquisition mode the oscilloscope samples the signal in evenly spaced intervals to construct the waveform Average In this acquisition mode the oscilloscope acquires several waveforms averages them and displays the resulting waveform You can use this mode to reduce random noise Peak Detect In this acquisition mode the oscilloscope finds the maximum and the minimum in every sampling interval and use these values to show waveform 3 12 Print And Print Preview setup Display CtrltH Load Data CtrltL Load Setup cave Data Ctrlts cave Setup Save mage Ctrl de Print Preview Print Option Connect Advanced Exit USER S MANUAL 72 DSO3062L 3062AL
40. number Pass It shows the pass waveform number Total It shows the total Pass Fail waveform number USER S MANUAL 54 DSO3062L 3062AL Digital Oscilloscope Operation Operate Click Start button to start the Pass Fail test Click Stop button to stop the Pass Fail test The Pass Fail function display NOTE Pass Fall function is unavailable in X Y mode Factory Setup Click Factory Setup in Utility menu to load default setups Vehicle W Record Fass Fail Factory Setup Language When you click the Factory Setup in Utility menu the oscilloscope displays the CH1 and CH2 waveforms and removes all other waveforms The oscilloscope set up for normal operation when it is shipped from the factory and can be recalled at anytime by user USER S MANUAL 55 DSO3062L 3062AL Digital Oscilloscope The Factory Setup function does not reset the following settings m Language option m Date and time Language Click Language in Utility menu Record Fass Fail F C Calibration Factory Setup Language Default English Hepi w English Deutsch There are four languages in Language menu The default language is English USER S MANUAL 56 DSO3062L 3062AL Digital Oscilloscope 3 Measure Signal Cursor Menu Click Cursor in main menu Lursor Messi Source Type d This method allows you to take measurements by moving the cursors
41. opes USER S MANUAL 100 DSO3062L 3062AL Digital Oscilloscope DSO3062AL Accessories USER S MANUAL X1 X10 two passive probes The passive probes have a 6MHz bandwidth rated 100Vrms CAT III when the switch is in the X1 position and a maximum bandwidth rated 300Vrms CAT II when the switch is in the X10 position Each probe consists of all necessary fittings A power adapter special for this product In addition to the power adapter shipped with your instrument you may purchase another one certified for the country of use A USB line used to connect external devices with USB interface like a printer or to establish communications between PC and the oscilloscope A PROBE HT322 A 20 pin logic analyzer exhaust line Eighteen little test hook HT321 Logic analyzer with high quality test hook A software installation CD and it contains the user manual for the oscilloscopes 101 DSO3062L 3062AL Digital Oscilloscope Appendix C General Maintenance General Care Do not store or leave the oscilloscope where the device will be exposed to direct sunlight for long periods of time Caution To avoid damages to the device or probes do not expose them to sprays liquids or solvents To avoid damages to the surface of the device or probes not use any abrasive or chemical cleaning agents Cleaning Inspect the device and probes as often as operating conditions require Make sure the device disconnect form
42. parameters USER S MANUAL 29 DSO3062L 3062AL Digital Oscilloscope 2 5 The Trigger System Click Setup gt Trigger The following figure shows the trigger system control Trigger Setup Single Bus Advanced setting Trigger Mode Edge yt Trigger Sweep AUTO yt Trigger Source Trigger Slope HF Rejection Single Trigger 1 Trigger Mode Sets the trigger mode 2 Trigger Sweep Selects the trigger sweep mode to AUTO NORMAL or SINGLE 3 Trigger Source Selects the trigger source to CH1 CH2 DO D15 EXT 4 Trigger Slope Selects the edge trigger slope to Positive or Negative slope Bus Trigger The Bus mode includes three trigger modes Trigger value Trigger at the appearance of a specified value on the selected bus Duration Trigger at x time after the appearance of a specified value Edge Trigger at the appearance of a specified value on the selected bus and rising falling or rising edge of the selected signal USER S MANUAL 30 DSO3062L 3062AL Digital Oscilloscope Trigger Setup Advanced Setting Trigger Mode Trigger value wt Advance Trigger There are four parts in each condition Data Duration Edge and Relative trigger value Trigger Setup Single Bus Advanced Data hin wax C Duration Min xsns Time Max xSns F Edge SOUrCe F Relative Trigger USER S MANUAL 31 DSO3062L 3062AL Digital Oscilloscope 2 6 Input
43. probe and ground nip to the Connector of Probe compensator 2 Set the CH1 probe attenuation of the oscilloscope to X10 The default is X1 USER S MANUAL 19 DSO3062L 3062AL Digital Oscilloscope 3 Attach the tip of probe and ground nip to the Connector of Probe compensator Click the button A square wave will be displayed within a several seconds Approximately 1 kHz 2V peak to peak 4 Inspect CH2 with the same method Repeat steps 2 and 3 1 7 Self Calibration The self calibration routine lets you optimize the oscilloscope signal path for maximum measurement accuracy You can run the routine at any time but you should always run the routine if the ambient temperature changes by 5v or more For accurate calibration power on the oscilloscope and wait twenty minutes to ensure it is warmed up To compensate the signal path disconnect any probes or cables from the input connectors Then access the Utility gt Calibration option and follow the directions on the screen The self calibration routine takes about several minutes USER S MANUAL 20 DSO3062L 3062AL Digital Oscilloscope 1 8 Accessories All the accessories listed below are standard accessories for the oscilloscope DSO3062L Probe x 2 1 5m 1 1 10 1 Passive Probes A power adapter special for this product A USB cable A logic analyzer cable Eighteen little test hook A software installation CD DSO3062AL
44. rement DSO3062L 3062AL Digital Oscilloscope 200mV to 100V div 20 1 Logic Analyzer Others Current Range CC65 20A CC65 60A CC650 CC 1100 F p 8 36V Wide range of input voltage suitable ower Source for vehicle power test Volume 255 x 190 x 45 mm Weight DSO3062AL Bandwidth 60MHz 3cB 1 Maximum Input 400V DC AC Peak Real Time Sampling Rate eee Time Base Range ons div to 1000s div 1 2 5 sequences Time Base Precision 50ppm Source CH1 CH2 D0 D15 EXT Mode Edge Pulse Video Alternative X Y mode USER S MANUAL 98 DSO3062L 3062AL Digital Oscilloscope Vpp Vamp Vmax Vmin Vtop Vmid Vbase Vavg Vrms Vcrms Preshoot Overshoot Voltage Measurement Frequency Period Rise Time Fall Time Positive Width Negative Width Duty Cycle Horizontal Vertical Track Auto Measure Modes Time Measurement Cursors Measurement Waveform Signal Process x FFT Invert Voltage Range 10mV to 5V div x 1 probe 100mV to 50V div x 10 probe 1V to 500V div x 100 probe 10V to 5000V div x 1000 probe 100V to 50000V div x 10000 probe 200mV to 100V div 20 1 Logic Analyzer High input impendence 200K C 10p 60V 60V 8 8V 100MHz 10MHz TTL LVTTL CMOS LVCMOS ECL PECL EIA 10K 68M CH Arbitrary Waveform Generator Mode DC 25MHz 2K 2Z00MHz adjustable 0 10 1CH waveform output 4KSa 12 bit lt 30ppm 3 5V Max Input Voltage range Logic thr
45. ring waveform data RUN The oscilloscope is running PLAY The oscilloscope is displaying the record waveforms USER S MANUAL 24 DSO3062L 3062AL Digital Oscilloscope 2 2 The Menu System The Main Menu File View Setup Display Cursor Measure Acquire Utility Vehicle Window Help 1 File Load or Save data setup EOE View Setup Display Hew Ctrlti Load Data CtrltL Load Setup cave Data Ctrlts Save Setup Save mage Print CtrltF Print Preview Print Option Exit 2 View Change the user interface w Toolbar ww Status Bar ww Side Bar 3 Setup Setup setting FE 7i splay Cursor Weasi REF Ctrltk MATH Ctrltm Trigger CtrltT Vertical Ctrlty Horizontal CtrltH Trigger Release Ctrltkh Bus Plug in USER S MANUAL 25 4 Display Change wave display type eae Cursor Measw Type d w Grid Ctrltty Intensity 5 Cursor Set Cursor measure type E i Source P Type d 6 Measure Set measurement parameters Measure Aequire Utility Sor ce Vertical Horizontal Clear Measure CtritM 7 Acquire Run Stop or other operation setting w Fun Ctrltk Stop Ctrlto Buffer Length d Aequisition d Interpolation d Autoset 8 Utility Utility setting Record Pass Fail FC d Calibration Factory Setup Languaze d USER S MANUAL DSO3062L 3062AL Digital Oscilloscope 26 9 Vehicle Tiagnosis Setup Clear reference waveform 10 Window Window setting
46. rtical Setup window In the sidebar you can change the channel coupling too Vertical CH1 vw OMJOFF 200 A al l i You can set the coupling to DC AC or GND If you set the coupling to DC it blocks the AC component of the input signal Probe Attenuation Setting Select the attenuation factor for the probe To check the probe attenuation setting toggle the probe menu to match the attenuation factor of the probe This setting remains in effect before you changed again Click Probe in Vertical Setup window to select the probe attenuation The probe setting window in the sidebar Vertical Zono 20v i 0g O Note The attenuation factor changes the vertical scale of the oscilloscope so that the measurement results refect the actual voltage levels at the probe tip Set Math Click MATH in Channel menu to set MATH channel USER S MANUAL 36 DSO3062L 3062AL Digital Oscilloscope The MATH Setup window BATH Setup ONMOFF Operate 4 6 Oa B VOLTS DIV OAxB Oars C FFT Source 4 CH1 Source A CH2 wy Cancel ON OFF Turn On Off the MATH Channel Source A B Set the sources of the math channel Operate Set operates type of the math channel Volt DIV Set the resolution of the math channel Probe Set the math channel probe attenuation Invert Turn on off the invert function The mathematic functions include addition subtract multiply and FFT for CH2 Source A
47. scilloscope Signal in X Y Format Instruction of the Ellipse Method Signal must be centered in X i i i A B I7 7 e T Sin A B or C D where 6 phase shift in degrees between the two signals From the formula above 9 _arcsine A B or _arcsine C D 8 must be in the range of O 11 2 or 311 2 2T1 if the main axis of the ellipse is between and Ill quadrant If the main axis is at Il and IV quadrant 8 must be in the range of 11 2 Tr or 1I 3T1 2 USER S MANUAL 81 DSO3062L 3062AL Digital Oscilloscope 4 5 Taking Cursor Measurements Use cursors to make time and amplitude measurements on a waveform quickly Measure the Peak Frequency or Time of the First Sine Waveform Do these steps 1 Click Cursor gt Source select CH1 select CH2 if you want measure CH2 2 Click Cursor gt Type select Vertical 3 Push left mouse button and the vertical lines appear 4 Drag the mouse button to the point you want to measure 5 Release the left mouse button the frequency difference and time difference will be shown at the status bar Measure the Frequency and Time Read the details showing in the status bar Freq 1 3B1EHz Time TASUS Measure the Amplitude of the First Waveform Peak of the Waveform Do these steps 1 Click Cursor gt Source select CH1 select CH2 if you want measure CH2 USER S MANUAL 82 DSO3062L 3062AL Digital Oscilloscope 2 Click Cur
48. sily such as the noise with large amplitude set the trigger level higher a little above the normal level and press and wait When noise occurs the instrument will record the waveform before and after the trigger USER S MANUAL 19 DSO3062L 3062AL Digital Oscilloscope 4 4 The Application of the X Y Operation X Y Plot acts to analyze correlation of data of two channels Lissajous diagram is displayed in the screen when you use X Y Plot which enables to compare frequencies amplitudes and phases of counterpart waveform against the reference waveform This makes it possible to compare and analyze frequency amplitude and phase between input and output Do these steps as follows 1 Set the probe attenuation to x10 Set the switch to x10 on the probes 2 Connect the CH1 probe to the input of the circuit and connect the CH2 probe to the output of the circuit 3 Click D button 4 Adjust the vertical scale and offset to display approximately the same amplitude signals on each channel 5 Select X Y format at Horizontal window The oscilloscope will displays a Lissajous pattern representing the input and the output characteristics of the circuit 6 Adjust the scale and offset of the horizontal and vertical to a desirable waveform display The following picture shows a typical example 7 Apply the Ellipse Method to observe the phase difference between the two channels USER S MANUAL 80 DSO3062L 3062AL Digital O
49. sor gt Type select Horizontal 3 Push left mouse button and the Horizontal lines appear 4 Drag the mouse button to the point you want to measure 5 Release the left mouse button the voltage difference will be shown at the status bar Measure the Amplitude i a a a a a a eS ee ae Ce eee ee Read the details showing in the status bar Wolt 16 6 Trace the Amplitude of a fixed position on X axis in a Waveform Do these steps 1 Click Cursor gt Source select CH1 select CH2 if you want trace CH2 2 Click Cursor gt Type select Trace 3 Click the cursor at the position that you want traced of the wave in the waveform window USER S MANUAL 83 DSO3062L 3062AL Digital Oscilloscope Trace the Amplitude Read the details showing in the status bar Volt 9 454 Note Click Cursor gt Type select Cross you can measure time and amplitude at one time USER S MANUAL 84 DSO3062L 3062AL Digital Oscilloscope 4 6 Logic Analyzer Caution This part is only used for DSO3062AL Set Bus Click the menu Setup gt Bus REF Ctrltk MATH Ctrl M Trigger CtrltT Vertical Ctrlt Horizontal CtrltH Trigger Release Ctrlth inal Logic Calibrate Data d DSO3062AL has 16 signals A0 A15 You can assign parts of them The user can click the panes E under the waveform window If the pane is green it means that you have opened it DO D15 panes B
50. splay and measure the horizontal parameters USER S MANUAL 59 DSO3062L 3062AL Digital Oscilloscope The Horizontal cursor display window The Horizontal cursor measure result display on status bar Volt 3 01 Measure Menu Click Measure in main menu The oscilloscope provides 20 parametric auto measurements 12 voltage and 8 time measurements Aequire Utility SOLE ie Yertical Horizontal Clear Measure CtritM 1 Source oe Vertical d CH Horizontal d Clear Measure CtrlitM The user can use the Source menu to select a measure source USER S MANUAL 60 DSO3062L 3062AL Digital Oscilloscope 2 Vertical ice Acquire Utility Source Vertical Maximam Horizontal Minimum Clear Measure Ctrltm Peak to Peak Top Base Middle EMS Amplitude Mean Cycle Mean Positive Overshoot Hegative Overshoot Maximum Voltage of the absolute maximum level Measured over the entire waveform Minimum Voltage of the absolute minimum level Measured over the entire waveform Peak To Peak Peak to peak Max Min Measured over the entire waveform Top Voltage of the statistical maximum level Measured over the entire waveform Base Voltage of the statistical minimum level Measured over the entire waveform Middle Voltage of the 50 level from base to top RMS The Root Mean Square voltage over the entire waveform Amplitude Amp Base Top Measured over the entire waveform Mea
51. the output wave The Arb waveform window as the following a ee Parameter Frequency Generate the Exponent waveform To output an Exponent Waveform please do the following steps 1 Press the check box On Off to open the wave output function 2 Select the Wave Type Exponent 3 Set the Wave Parameters USER S MANUAL 93 DSO3062L 3062AL Digital Oscilloscope Frequency Set the output wave frequency Amplitude Set the output wave amplitude Y Offset Set the output wave vertical level offset Phase Set the output wave phase Tao Set the ouput wave Tao param Rise Set the output wave slope The Exponent waveform window as the following Parameter Frequency Exponent Frequency 1200000Hz VPKtoPK 4000V O OOOO O Hz 0 75MHz Y 035 a E 0 01 0 Generate the White noise waveform To Generate a White noise Wave please do the following steps 1 Press the check box On Off to open the wave output function 2 Select the Wave Type White 3 Set the Wave Parameters Amplitude Set the output wave amplitude The White noise waveform window as the following Parameter Amplitude w 0735Y J USER S MANUAL 94 DSO3062L 3062AL Digital Oscilloscope Synchronized output If you generate a waveform by software there is a synchronized signal output from SYNC terminal The signal is square waveform the frequency of which is equal to the waveform you generated For examp
52. waveform number Operation Operate Click Start button to start the Pass Fail test USER S MANUAL Tf DSO3062L 3062AL Digital Oscilloscope Click Stop button to stop the Pass Fail test The Pass Fail function display NOTE Pass Fall function is unavailable in X Y mode USER S MANUAL 78 DSO3062L 3062AL Digital Oscilloscope 4 3 Capturing a Single Shot Signal To capture a single event it needs to gather some pre test knowledge of the signal in order to set up the trigger level and slope correctly For example if the event is derived from 3 3V COMS logic a trigger level of 1 2 or higher Volts should work on a rising edge Do these steps as follows 1 Set the probe and the channel attenuations to X 10 2 Set up the trigger in the Trigger Menu or in the Trigger Setting window 1 Adjust the Trigger Mode to Edge 2 Set the Trigger Sweep to Single 3 Set the Trigger Source to CH1 4 Set the Trigger Slope to which means you select the rising edge 5 Adjust the Volts Div and the time base in a proper range for the signal 6 Drag the trigger level sign on the waveform display screen to proper position It ally higher a little above the normal level 7 Click START button to start capturing When the trigger conditions are met data appears on the display representing the data points that the oscilloscope obtained with one acquisition This function helps to capture the signal occurrence ea

USER`S MANUAL

Contents

Download Pdf Manuals

Related Search

Related Contents