Home

SNV-5080 User Manual

1. Item Description ALARM IN Used to connect the alarm input signal Alarm In Out ALARM OUT Used to connect the alarm output signal terminals ALARM COM Common port where the alarm output signal is connected GND Used for earth grounding SD Memory Card Compartment Compartment for the SD memory card Resets the camera settings to the default Press and hold it for about 5 seconds to turn off the system indicator and restart the system 3 Reset Button E Resetting the camera requires reconfiguration of network settings IP address subnet mask gateway address etc using the IP Installer software application 16_ overview Components COUCH e e E o Item Inner Cover Side wing hooks ZOOM lever Focus lever SD Memory Card Compartment Monitor Out Wiring Cover Lock Release MAIAdSAO Description Cover for the main unit s protection By lifting it while gently pressing the both ends you can separate the inner cover Turn the
2. MAIAdSAO Item Description ALARM IN Used to connect the alarm input signal Alarm In Out ALARM OUT Used to connect the alarm output signal manne ALARM COM Common port where the alarm output signal is connected Used for earth grounding SD Memory Card Compartment for the SD memory card Compartment Resets the camera settings to the default Press and hold it for about 5 seconds to turn off the system indicator and restart the system 3 Reset Button E Resetting the camera requires reconfiguration of network settings IP address subnet mask gateway address etc using the IP Installer software application English _19 Overview Components 1 Inner Cover 2 Side wing hooks 3 ZOOM lever 4 Focus lever 5 Monitor Out 20_ overview Description Cover for the main unit s protection By lifting it while gently pressing the both ends you can separate the inner cover Turn the barrel left or right to adjust the zoom and turn the knob clockwise to lock the zoom Turn the barrel left or right to ad
3. XN LG MAIAdSAO Do not place a glass of water on the product OK Do not block any ventilation openings Do not install near any magnetic sources User s Manual is a guidance book how to use the products The meaning of the using sign in the book is following e Reference In case of providing information for helping of product s us ages e Notice If there s any possibility to occur any damages for the goods and human caused by not following the instruction X Please read this manual for the safety before using of goods and keep it in the safe place English _5 overview N C eco RoHS compliant 6_ overview This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense samsung Techwin cares for the environment at all product manufacturing stages and is taking measure
4. Close and restart the web browser and try to access the Web Viewer When Siverlight Runtime is properly installed you will see the Live screen ee For normal installation set the Block Popup setting as follows Internet Explorer Tools Block Popup Always allow popups from the current site A English _65 YAMAIA GAM web viewer USING THE LIVE SCREEN SSMS idsis S amp SAMSUNG ros G A ta Mh h 10 eee oa 9 LY 8 Ley IS e gt CSE ol Ki Item Monitoring Playback Setup Viewer Screen Alarm Output Audio Reset Alarm Camera Menu Digital PTZ Screen Optimization Full Screen 66_ web viewer ee ag o E E Description Move to the monitoring screen Switch to the monitoring screen that plays recording data in the SD memory Move to the Setup screen Displays the Live video on the screen Activate the Alarm Out port Display the audio Listen and Talk toggle button on the screen Reset the alarm output settings Used to retrieve and customize the Camera Setup menu For selecting and saving each menu item refer to How to use the menu key page 53 You can use the mouse wheel to activate the digital zooming Adjust the screen to the optimal size and display the Full Screen icon on the Live screen 11 Capture 12 Video Format Saves the snapshot as an image file in the jpeg or omp format You c
5. into another language Hereinafter translation is included without limitation in the term modification Each licensee is addressed as you Activities other than copying distribution and modification are not covered by this License they are outside its scope The act of running the Program is not restricted and the output from the Program is covered only if its contents constitute a work based on the Program independent of having been made by running the Program Whether that is true depends on what the Program does 1 You may copy and distribute verbatim copies of the Program s source code as you receive it in any medium provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty keep intact all the notices that refer to this License and to the absence of any warranty and give any other recipients of the Program a copy of this License along with the Program You may charge a fee for the physical act of transferring a copy and you may at your option offer warranty protection in exchange for a fee You may modify your copy or copies of the Program or any portion of it thus forming a work based on the Program and copy and distribute such modifications or work under the terms of Section 1 above provided that you also meet all of these conditions a You must cause the modified files to Carry prominent notices stating that you changed
6. 3 rules including the virtual line and the specified area condition For more information about lt Activation time gt and lt Action gt refer to Alarm Input page 79 Specify whether or not the alarm area is displayed If you set it to lt On gt the suspect area where the alarm occurs will be marked in a red box 80_ setup screen To use the IV analysis function according to the virtual line based rule 1 Set the event rule to lt Virtual line based Click a desired area in the video and Select a desired lt Virtual Line Rules gt Set lt IV analysis function gt to lt Enable gt rules gt drag it to the end point and right click it You can specify up to 3 event rules for the virtual line e Right A movement from left to right in the virtual line will be detected e Left A movement from right to left in the virtual line will be detected e Both A movement in any direction in the virtual line will be detected NJJY0S dNLAS Click OK To cancel the existing line right click on the line and select Delete in the context menu When done click Apply To use the IV analysis function according to the defined area based rule Set lt IV analysis function gt to Set the event rule to lt Defined area Select the vertex of a desired area lt Enable gt based rules gt and right click it to display the context menu Select a desired
7. Port 9 Video Out Port 14_ overview Resets the camera settings to the default Press and hold it for about 5 seconds to turn off the system indicator and restart the system Resetting the camera requires reconfiguration of network settings IP address subnet mask gateway address etc using the IP Installer software application Used to plug the power cable Used for earth grounding Used to connect a PoE or LAN cable ALARM IN Used to connect the alarm input signal ALARM OUT Used to connect the alarm output signal ALARM COM Common port where the alarm output signal is connected GND Used for earth grounding Video signal output port connected to the monitor AT A GLANCE SND 5080 Appearance Item Dome Cover Main unit Power Port Video Out Port Network Port Audio In Jack Siel e J amp le Audio Out Jack MAIAUSAO U a nt 4 bb bs Description Dome cover for the lens and unit protection Main unit includes the lens switch board PCB boards and screws Used to plug the power cable Video signal output port connected to the monitor Used to connect a PoE or LAN cable Used to connect to a microphone Used to connect to speakers English _15 overview Inside
8. a selected item use the Left Right lt gt buttons To break down to a sub menu structure click Enter on the selected item lt 4 This arrow appears next to a menu that contains sub items a f lt IV analysis function gt is enabled camera s OSD menu operation can be set as an event CAMERA MENU SETUP You can change the camera settings according to the environment where the camera is located SSDR Samsung Super Dynamic Range Setup In a scene where the difference between bright and dark is severe you can increase the brightness of the dark area alone to regulate the overall brightness A V gt lt gt gt ENTER gt A V gt lt gt gt ENTER 1 Move to lt SSDR gt and select lt ON gt MAIN SETUR gt OSDIR WHITE BACKEIGHil English _53 camera setup 2 Configure the lt SSDR gt and lt D RANGE gt settings as necessary SSR SETUP e SSDR Adjust the level of the dynamic range ARRON e D RANGE Select the amplitude area of the dynamic range 3 When completed select lt RETURN gt to return to the previous screen White Balance Setup You can correct the image colors based on white under any lighting conditions A V gt lt gt gt ENTER gt A V gt lt gt gt ENTER 1 Move to lt WHITE BAL gt and select a setting value MAIN SETUP e ATW Corrects the colors of the camera RSDR ON video automatically e MANUAL You can adjust the red and Ee ont pa blu
9. access from only those IPs that are added to the filtering will be accepted 4 Provide the IP that you want to grant or deny access from 5 When done click Apply z EER PRP R RHEE i i TT LLLE SSL You can select a secure connection system or install the public certificate for this purpose 1 From the Setup menu select the lt Network E gt tab 2 Click lt SSL gt 3 Select a secure connection system To access the camera using HTTPS mode you have to type the IP address for the camera in the form of https lt Camera_IP gt 4 Search for the public certificate that you want to install on the camera To install the certificate on the camera you need to provide a certificate name it can be arbitrarily assigned by the user certificate file issued from the certification author ity and a key file The lt HTTPS Secure connection mode using the public certificate gt item will be active only if there exists a public certificate installed 5 When done click Apply English _75 N3JJY0S dNLAS Setup screen Registering with DDNS To register your product with the Samsung DDNS 1 Visit the iPOLIS web site www enon ur samsungipolis com and sign in with a registered account ee a ha POLE sebane Ea ie ee eee be peg ey ee te ees H hiia 2 From the top menu bar select lt DDNS SERVICE gt lt MY DDNS gt 3 Click PRODUCT REGISTRATION 4 Enter the product
10. and thus to each and every part regardless of who wrote it Thus it is not the intent of this section to claim rights or contest your rights to work written entirely by you rather the intent is to exercise the right to control the distribution of derivative or collective works based on the Program In addition mere aggregation of another work not based on the Program with the Program or with a work based on the Program on a volume of a storage or distribution medium does not bring the other work under the scope of this License 3 You may copy and distribute the Program or a work based on it under Section 2 in object code or executable form under the terms of Sections 1 and 2 above provided that you also do one of the following a Accompany it with the complete corresponding machine readable source code which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange or b Accompany it with a written offer valid for at least three years to give any third party for a charge no more than your cost of physically performing source distribution a complete machinereadable copy of the corresponding source code to be distributed under the terms of Sections 1 and 2 above ona medium customarily used for software interchange or c Accompany it with the information you received as to the offer to distribute corresponding source code This alternative is a
11. audio amp video network event and system settings of the camera in the network Video Profile 1 From the Setup menu select the lt Audio amp Video E gt tab 2 Click lt Video Profile gt 3 Select a lt Video Profile gt number 4 Click the input box of each item and enter select a desired value The context menu may differ depending on the selected codec type e Default Profile This is the default video profile e Fixed Framerate Profile Fix the frame rate of the selected profile regardless of the settings of other profiles e E mail FTP Profile Video profile to be transferred to the specified email or FTP site Only the MJPEG codec can be set as the E mail FTP Profile e Record Profile This is the profile that is applied to video recording 5 When done click Apply 70_ setup screen To add a video profile You can add as many codec as necessary so that a variety of profiles can be applied according to the recording condition 1 Select a profile number Provide the name and select a codec 2 3 Specify the conditions under which the codec will be applied 4 Specify the details of the selected codec including resolution and frame rate Resolution Set the video size of the MPEG4 H 264 and MJPEG files Framerate Specify the frame rate Compression Specify the compression rate of the video Bitrate control You can select either the fixed bit rate or the
12. barrel left or right to adjust the zoom and turn the knob clockwise to lock the zoom Turn the barrel left or right to adjust the focus and turn the knob clockwise to lock the focus Compartment for the SD memory card Using the test monitor cable you can connect to a mobile display for camera test If you drill a hole in the wiring cover for wiring remove the cover and attach the provided dustproof plate to it and arrange the cables through the plate The dust proof plate is to prevent outside dust from inflow to the wiring compartment To separate the bracket from the main unit for the installation or to separate the camera from an installed camera push this release and turn the main unit in the marked direction of lt UNLOCK gt English _17 overview AT A GLANCE SND 5080F Appearance Item Dome Cover Main unit Power Port Video Out Port Network Port Audio In Jack Audio Out Jack Sel e Oe 18_ overview lhi Description Dome cover for the lens and unit protection Main unit includes the lens switch board PCB boards and screws Used to plug the power cable Video signal output port connected to the monitor Used to connect a PoE or LAN cable Used to connect to a microphone Used to connect to speakers Inside
13. desired title in the bottom CAMERA TLE SETUP input line ABCDEFOHI J KLM You can enter up to 15 characters for the title NOPORS TUVWXYZ albedoareimi i kim f NODC TES t UVM 4 Select lt POS gt and specify where to gt 0125466 730 display the camera title S gt Whi OS lay When the camera title is displayed use the direction buttons to specify the position Click OK to return to the previous menu 5 When done select lt END gt To cancel your input select lt CLR gt 6 When completed select lt RETURN gt to return to the previous screen dNLAS VHANVO OSD Color You can set the OSD color on the screen to your preference 4 gt ENTER gt A V gt lt gt gt ENTER 1 Select lt SPECIAL gt MAIN SETUP SSD ON WAITS EYAL ATW BACKHGNU OFF POSURE gt SPECIAL 4 EXIN 2 Move to lt OSD COLOR gt and select a desired color SPECIAL SETUP 3 When completed select lt RETURN gt to CAM TLE return to the previous screen gt OSD COLOR DANIK AGE AD RETURN English _59 camera setup Day Night Mode Setup You can switch the mode to adjust the black and white level as well as the colors A V gt lt gt gt ENTER gt A V gt lt gt gt ENTER 1 Select lt SPECIAL gt MAN SETUP SSDR ON WHNE BAL NW mvMerueHy OFF POSURE gt SPECIAL 4 EXIT 2 Select lt DAY NIGHT gt and specify a desired mode setting value SPECIAL SETUP e AUTO Displays in co
14. domain You must perform the duplicate check for the domain that you entered 5 Select a lt CLASSIFICATIONS and specify the lt MODEL NUMBER gt 6 Specify the product location with a description if necessary 7 Click REGISTRATION n The product will be added to the prod cance uct list that you can check eee bees eee eed ee eee ape se ee ee a meee amp ee ee 76_ setup screen To connect to the Samsung DDNS in camera setup 1 From the DDNS setup page set lt DDNS gt to lt Samsung DDNS gt 2 Provide the lt User Name gt and lt Password gt that you registered with the DDNS site 3 Click Apply When the connection is successfully made you will see the message of lt Success gt on the screen N3aYOS dNLAS EVENT SETUP FTP Email You can configure the FTP Email server settings so that you can transfer the images stored in the camera to your PC if an event occurs 1 From the Setup menu select the lt Event J gt tab 2 Click lt FTP Email gt 3 Select lt FTP Configuration gt or lt Email Configuration gt and enter select a desired value e FTP Configuration Server Address Enter the IP ad dress of the FTP server that you transfer the alarm images to User ID Enter the user ID with which you will log in to the FTP server Password Enter the user account password for logging into the FTP server Upload Directory Specify the FTP path where you wil
15. lt Defined Area Rules gt You can specify up to 3 defined area event rules e Entering An event where a moving object passes through the defined area and enters inside will be detected e Exiting An event where a moving object passes through the defined area and exits outside will be detected e Appearing Disappearing An event will be detected where an object that has not existed in the area until the previous frame suddenly appears or disappears in the area without passing through the defined area Click OK To cancel the specified area right click on the area and select Delete in the context menu When done click Apply English _81 Setup screen To use the IV analysis function according to the whole area based rule 1 Set lt IV analysis function gt to lt Enable gt 2 Set the event rule to lt Entire area based rules gt 3 Select a desired lt Entire Area Rules gt e Appearing An event where an object that has not existed suddenly appears will be detected e Disappearing An event where an object that has existed suddenly disappears will be detected e Scene Change An event where the screen is changed at more than a certain time interval will be detected You can set the lt Scene Change gt rule along with rules lt Appearing gt and lt Disappearing gt 4 Click OK 5 When done click Apply Time Schedule You can configure so that an event will occur at
16. server If this is the case you will not be informed of the IP address changed by DDNS Once you register a dynamic IP based device with the DDNS server you can easily check the changed IP when you try to access the device To add the IP address to the lt DDNS gt server visit www samsungipolis com and register your device and set the DDNS option to lt Samsung DDNS gt before providing the user ID and password for the DDNS server YAMAIA GAM LOGIN The default user ID is admin and the default password is 4321 1 Enter admin in the lt User Name gt fries Hatea ik PT input box Thit bicai eb its a 12 a Op ean yu bo beg ai 2 Enter 4321 in the lt Password gt input Sapa ee ere box If the password is changed enter the WaHe changed password instead rowed 3 Click OK A ee If you have logged in successfully you emm will the Live Viewer screen 4 For security purposes ensure that you change the password in lt System gt lt User gt The administrator ID admin is fixed and can not be changed f you check the Save this password in your password list option when your input is done you will be logged in automatically without being prompted to enter the login information from next time on i m f you are using Internet Explorer 7 0 or 8 0 as the default web browser you can view the best quality image with a screen ratio of 100 Reducing the ratio may cut the image on the borders
17. settings manually 13 Exit Exits the IP Installer program STATIC IP SETUP Manual Network Setup Run lt IP Installer exe gt to display the camera search list At the initial startup both Auto Set and Manual Set will be grayed out O For cameras found with the IPv6 setting these buttons will be grayed out as the cameras do not support this function 1 Select a camera in the search list Find the MAC Ethernet address labeled on the rear of the camera Both the Auto Set and Manual Set buttons will be activated 2 Click Manual Set The Manual Setting dialog appears The default values of lt IP Address gt lt Subnet Mask gt lt Gateway gt lt HTTP Port gt and lt VNP Port gt of the camera will be displayed The default lt Password gt is 4321 English _47 dN13S ANY NOILOANNOO MYOMLAN network connection and setuo 3 In the lt Address gt pane provide the Menusl Setting necessary information WTF Pon iA MAC Ethernet Address The MAC nes Si WNP Pot p Ethernet address of the applicable Sutnet Mask O E Giteway Ls Teal i T camera will be set automatically so you don t need to input it manually Paaiword If using an IP router e P Address Enter an address falling in the IP range provided by the IP router ex 192 168 1 2 254 192 168 0 2 254 192 168 XXX 2 254 e Subnet Mask The lt Subnet Mask gt of the IP router will be the lt Subnet M
18. to multicast check whether there is a router that supports multicast in the LAN the camera is connected to English _91 XIGNAddV aooendix PROBLEM No JPEG file is transferred via e mail on occurrence of intelligent video analysis event of camera even when the lt IV analysis Function gt is set to lt Enable gt SOLUTION e Verify the settings in the following sequence A Check lt Data amp Time gt settings B The lt lV analysis Function gt should be set to lt Enable gt C Alarm Video Transmission must be enabled Can lt Set Rules gt be configured even when the lt lV analysis Function gt is set to lt Disable gt e Yes it can be You can set rules for events despite of the intelligent video analysis setting No signal is found at the Alarm Output port even when an intelligent video analysis event is generated Cannot record into the SD memory card e Check alarm output port settings e Check if the memory card is defective e Check if the write protection tab of the memory card is set to Lock SD memory indicator does not turn on even when the SD memory card is inserted e Check if the memory card is defective e Check if the lt Record gt is checked in lt Setup gt gt lt Event gt gt lt SD Record gt menu SD memory card is inserted but the camera does not operate properly Cannot format the SD memory card 92_ appendix e Check if the memory card
19. v3 MIB 2 ARP DNS DDNS Protocol IPv6 TCP IP HTTP HTTPS SSL DHCP Streaming Unicast Multicast HTTPS SSL Login Authentication Security Digest Login Authentication IP Address Filtering User access Log DDNS Supporting Samsung DDNS and Public DDNS services Max 10 Users at Unicast Mode Maximum User Access Max 20 Users at Multicast Mode Connection Administrator Full Control Privilege User Access PEP aval Guest Live Monitoring only Additional User Configurable privilege individually Pre Post Alarm Image Buffering Alarm Input Image Recording SD memory Event Notification Event Intelligent Motion Detection E mail Notification Management Alarm Out Activation JPEG Image transfer FTP Schedule Image Recording SD memory Alarm Out Activation Windows XP VISTA 7 Supported 0S Mac OS Internet Explorer 7 0 or Higher aaa aia Firefox ae Chrome Safa na ASSI PTZ Control Digital PTZ based on Mega Pixel Resolution pe Plug in MS SilverLight 4 0 Default English French Germany Spanish Italian UI Language Chinese Korean Russian Japanese Swedish Denish Portuguese S W upgrade Using Web viewer UI Video Player RTP RTSP streaming Quicktime VLC player Video Management samsung CMS S W 3rd Party S W appliction Software Application IP Installation IP Installer Application for All Samsung IP Devices 90_ appendix TROUBLESHOOTING PROBLEM can t access the camera from a web browser Viewer got disconnected during monit
20. 20 The port range of the Web Viewer is between 4502 and 4532 If the VNP port is with this effective range the Web Viewer port should be specified the same as the VNP port 4 When done click Apply DDNS DDNS is an abbreviation of Dynamic Domain Name Service that converts the IP address of a camera into a general Host Name so that the user can easily remember it 1 From the Setup menu select the lt Network E gt tab 2 Click lt DDNS gt 3 Select lt DDNS gt 4 Type in the DDNS items according to the selected type e Samsung DDNS Select this if you use the DDNS server provided by Samsung Techwin e Public DDNS Select this if you use a public DDNS server Host Name Enter the name of the host i e host name of Dyndns that is registered with the DDNS server a a Es Sl a ee Eas a 74_ setup screen User Name Enter the user name for the DDNS service i e user ID that is registered with Dyndns Password Enter the password for the DDNS service i e password that is registered with Dyndns 5 When done click Apply IP Filtering You can create a list of IPs that you want to grant or deny access to them 1 From the Setup menu select the lt Network E gt tab 2 Click lt IP filtering gt 3 Select a lt Filtering Type gt e Deny If selecting this access from those IPs that are added to the filtering will be restricted e Allow If selecting this
21. 32 2195 Park Chertsey Surrey UNITED KINGDOM KT16 OPS www samsungcctvusa com TEL 44 1932 45 5300 FAX 44 1932 45 5325 www samsungsecurity com www samsungipolis com VAN 10 04
22. 5 46 47 50 51 52 52 Important Safety Instructions Product Features Recomended PC Specifications What s Included At a Glance SNB 5000 At a Glance SND 5080 At a Glance SND 5080F At a Glance SNV 5080 MAIAdSAO Installation SGND 5080 Installation SND 5080F Installation SNV 5080 Mounting the Lens Inserting Removing an SD Memory Card Memory Card Information Not Included Connecting with other Device Connecting the Camera Directly to Local Area Networking Connecting the Camera Directly to a DHCP Based DSL Cable Modem Connecting the Camera Directly to a PPPoE Modem Connecting the Camera to an IP Router with the PPPoE Cable Modem IP Address Setup Static IP Setup Dynamic IP Setup Port Range Forward Port Mapping Setup Connecting to the Camera from a Shared Local PC Connecting to the Camera from a Remote PC via the Internet English _7 overview 8_ overview CAMERA SETUP WEB VIEWER SETUP SCREEN APPENDIX 53 53 62 63 64 66 67 68 70 70 73 77 83 87 89 91 93 How to use the Menu Key Camera Menu Setup Connecting to the Camera Login Installing Silverlight Runtime Using the Live Screen Using OSD Screen Menu Playback Setup Audio amp Video Setup Network Setup Event Setup System Setup Camera Specification Network Specification Troubleshooting GPL LGPL Software License PRODUCT FEATURES HD Video Quality Supports up to 1 3 meg
23. 7 NOILOANNODO 8 NOILVTIVLSNI Adjusting the monitoring direction for the camera SND 5080 SND 5080F SNV 5080 Tilting a JF f 1 SQ TY Lens rotation You can adjust the camera direction only when the camera is fixed on the ceiling Then turning the camera to the left or right is referred to as Panning while tilting the angle is Tilting For panning the panning limit is 220 for the clockwise and 120 for the counterclockwise a total of 340 enabled further rotation is stopped by the stopper English _31 Installation amp connection MOUNTING THE LENS Disconnect the power before proceeding O m The C lens and CS lens are not included in the product package You must use the mega lens only for this purpose O CS Lens A Mounting the C lens Turn the C mount adaptor clockwise to insert it and do the same with the C lens Mounting the CS lens Turn the optional CS lens clockwise to insert it C Lens 32_ installation amp connection Connecting the Auto Iris Lens connector Insert the lens connector into the corresponding hole of the camera Focusing Turn the lens left or right to control the zoom and focus the lens so that you can view a clear sharp object NOILOANNODO 8 NOILVTIVLSNI INSERTING REMOVING AN SD MEMORY CARD Inserting an SD Memory Card Push the SD memory card in th
24. 76 V 1 49M pixels Effective 1 329 H x 1 049 V 1 39M pixels Min Scene Color Sens Up Off 0 3Lux F1 2 50 IRE Illumination B W Sens Up Off 0 01Lux F1 2 50 IRB Privacy Mask Off On 12 Programmble Zones Day Night Color BW AUTO IR Cut Filter Backlight Compensation BLC HLC SSDR Off Electronic Shutter Speed Auto 1 30 30 000sec A FLK Manual Gain Control Off Low Medium High Manual uni Sens Up Off Auto Seletable up to 60X nction l unctions a Noise Reduction Off On Level Adjusment White Balance ATW AWC Manual Indoor Outdoor On Screen Display Yes Camera Title Support English French Germany Spanish Italian OSD Language Chinese Korean Russian Japanese Swedish Denish Portuguese Video Output VBS 1 0Vp p VBS 1 0Vp p S N Ratio S N Ratio About 50 dB English _87 XIGNAddV aooendx Items SNB 5000 SND 5080 F SNV 5080 Focal Length Fe 2 8 10mm Zoom ratio X3 6 Aperature Ratio F1 2 Lens Ea Tele 28 8 H x 21 60M Viewing Angle 3 Wide 94 6 H x 68 4 V Lens Drive Type Manual DC AI DC Mount Type CS C Board Type s 40 C 50 C Environmental Operating Temperature 10C 50C Fan Heater Built in Conditions Humidity 0 90 0 90 Waterproof Power Requirement AC24V DC12V PoE Power Power Consumption 6W 7W A LED Indicator Yes Dimensions 129 5 H x133 0 WxHxD Net 72x 60x138 6
25. E MOUNT ADAPTOR SCX 300PM This is an adaptor for WALL MOUNT ADAPTOR SCX 300WM installation on a pole whose diameter is bigger than 80mm O English _29 NOILOANNODO 8 NOILVTIVLSNI Installation amp connection 4 CORNER MOUNT ADAPTOR SCX 300KM This is an adaptor for WALL MOUNT ADAPTOR SCX 300WM installation on the YY corner of wall joint L Installing on the ceiling directly 1 Using the L wrench provided loosen 3 screws by turning them counterclockwise and separate the dome cover 2 Loosen 3 screws by turning them counterclockwise press both left and right lock releases inwards in arrow direction to unlock the stopper and then separate the camera from the case 30_ installation amp connection 3 Drill holes diameter 5mm more than 35mm deep on the ceiling by matching to the holes on the case bed and insert plastic anchors HUD 5 fully into the holes Fix the case bed on the ceiling by using Tapping Screws TH M4xL30 4 places 4 Connect power and video cables and arrange cable running not to damage or squeeze them and assemble the camera unit in the reverse way 5 Adjust the lens aiming to your desired direction 6 Assemble the Dome Cover For waterproof purpose fix and secure the bolt using L wrench provided 4 m For the wall mounting installation and how to connect the alarm cables refer to the installation instructions of SND 5080F pages 26 2
26. English _63 web viewer This network camera uses Microsoft Silverlight for displaying the video INSTALLING SILVERLIGHT RUNTIME If your PC has not installed Silverlight Runtime or has just installed an old runtime version you will be redirected to the Silverlight Runtime installation page automatically when accessing the web viewer 1 Click lt Click Here gt STE A gt oe a ores G7 G a there if ret al og Stherrlight Franteor Lertall 2 When the file download dialog pops up click lt Run gt File Download Security Warning Do p u manl bo ium oe tava Ihir Ia e Hame Sivarbyht Devekper mme Type Application 7 63 86 Feo 092 800 i es ee e ara tikes bene Hie beret cam Gap uehd Chen ibe tegen cin pobariush hate por iriga pou dbo eed bred Bhs ranca dle not fun et hirea Lhe alter a i Ue met 3 When the download is completed click lt Run gt inernet Explorer security Warning Ie yim ean bo ron child alare Enr asters Ce Care aie Files ron thes Greet fee bo usaid Bi Abe typt cii pairti hata yawn fonputer Gh rui daana ara pn yr Evel a the k 4 The Silverlight Runtime installation page will be displayed lt Install now gt to Phar tela 4 proceed with the installation 3 Why ichrig beata acre yo anca the Dheera yY koe oer Seriji i Silverlight 64_ web viewer 5 When done click lt Close gt Silom conganta Thal and nequared for automatic updates ara 6
27. Network Camera SNB 5000 SND 5080 SND 5080F SNV 5080 User Manual Before installing and operating this product please read this manual thoroughly English overview IMPORTANT SAFETY INSTRUCTIONS N OO 0 e 0 D 10 11 12 13 14 Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with dry cloth Do not block any ventilation openings Install in accordance with the manufacturer s instructions Do not install near any heat sources such as radiators heat reaisters stoves or other apparatus including amplifiers that produce heat Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet Protect the power cord from being walked on or pinched particularly at plugs conve nience receptacles and the point where they exit from the apparatus Only use attachments accessories specified by the manufacturer Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used Use caution when moving the cart apparatus combinat
28. RNET S beef PPPoE or PPPoE or ee IP Router Cable Modem Cable Modem External Remote PC DDNS Server ata Center KOREA dN13S ANY NOILOANNOO MYOMLAN Configuring the network settings of the local PC connected to an IP router Configuring the network settings of the local PC connected to an IP router follow the instructions below e Select lt Network Neighborhood gt gt lt Properties gt gt lt Local Area Connection gt gt lt Properties gt gt lt General gt gt lt Internet Protocol TCP IP gt gt lt Properties gt gt lt Obtain an IP address automatically gt or lt Use the following IP address gt e Follow the instructions below if you select lt Use the following IP address gt ex1 If the address LAN IP of the IP router is 192 168 1 1 IP address 192 168 1 100 Subnet Mask 255 255 255 0 Default Gateway 192 168 1 1 ex2 If the address LAN IP of the IP router is 192 168 0 1 IP address 192 168 0 100 Subnet Mask 255 255 255 0 Default Gateway 192 168 0 1 ex3 If the address LAN IP of the IP router is 192 168 xxx 1 IP address 192 168 xxx 100 Subnet Mask 255 255 255 0 Default Gateway 192 168 xxx 1 4 For the address of the IP router refer to the product s documentation English _45 network connection and setuo IP ADDRESS SETUP Sean Ren E P r Saith Anio Sai Manual Sat j ea Buttons used in IP Installer Item Device Nam
29. URN and clearer the outline of the image becomes e GAMMA Adjust the contrast of the image e COLOR LEVEL Adjust the color level of the image 4 When completed select lt RETURN gt to return to the previous screen English _61 web viewer CONNECTING TO THE CAMERA Normally you would a Bing VES ThE D NON icneeeli interest Lapisre 1 Launch the Internet browser 2 Type the IP address of the camera in the address bar o gt Teves sae oe 81680 amam natn ex IP address IPv4 192 168 1 100 Pen Us Hama rt Pet at om Pe http 192 168 1 100 the Login dialog should appear N e IP address IPv6 2001 230 abcd O E ee ffff 0000 0000 ffff 1111 gt http 2001 230 abcd ffff 0000 0000 ffff 1111 If the HTTP port is other than 80 1 Launch the Internet browser 2 Type the IP address and HTTP port number of the camera in the address bar ex IP address 192 168 1 100 Port number 10000 gt http 192 168 1 100 10000 the Login dialog should appear Using URL 1 Launch the Internet browser 2 Type the DDNS URL of the camera in the address bar ex URL address http www samsungipolis com Product ID the Login dialog should appear 62_ web viewer To check the DDNS address If the camera is connected directly to the DHCP cable modem DSL modem or PPPoE modem the IP address of your network will be changed each time you try to connect to the ISP Internet Service Provider
30. Y for details type show w This is free software and you are welcome to redistribute it under certain conditions type show c for details The hypothetical commands show w and show c should show the appropriate parts of the General Public License Of course the commands you use may be called something other than show w and show c they could even be mouse clicks or menu items whatever suits your program You should also get your employer if you work as a programmer or your school if any to sign a copyright disclaimer for the program if necessary Here is a sample alter the names Yoyodyne Inc hereby disclaims all copyright interest in the program Gnomovision which makes passes at compilers written by James Hacker signature of Ty Coon 1 April 1989 Ty Coon President of Vice This General Public License does not permit incorporating your program into proprietary programs If your program is a subroutine library you may consider it more useful to permit linking proprietary applications with the library If this is what you want to do use the GNU Lesser General Public License instead of this License GNU GENERAL PUBLIC LICENSE Version 3 29 June 2007 Copyright 2007 Free Software Foundation Inc lt http fsf org gt Everyone is permitted to copy and distribute verbatim copies of this license document but changing it is not allowed 0 Additional Defini
31. a item to play inthe search list 6 Click the Play J button 7 To stop playing the video click Stop E To return to the search screen click Exit EEN Moon e196 DIADA beer To capture the snapshot 1 Click JEM on the scene to capture The Capture dialog should appear 2 Click Save The screenshot will be saved in the specified path m m f you are using the Internet Explorer as the default web browser select Tools Internet Options Security and uncheck Use protected mode 68_ web viewer To check the information of the searched video Click the About fj button To back up the searched video 1 Click JJ on the scene to back up The Capture dialog should appear 2 Click Save The screenshot will be backed up to the specified path YAMAIA GAM To download SlimPlayer You can download SlimPlayer that is designed to play videos stored in your PC 1 Click SlimPlayer J You will see a download dialog where you can specify the download path 2 Specify the path with a proper file name and click Save 3 Unzip the downloaded file and run the executable English _69 Setup screen SETUP You can configure the audio amp video network event and system settings of the camera in the network 1 In the Live screen click lt Setup EJ gt 2 The Setup screen appears AUDIO amp VIDEO SETUP You can configure the
32. a pixels of HD video quality H 264 MPEG 4 MJPEG Multi Streaming This network camera supports the H 264 MPEG 4 MJPEG codec and can display videos in different resolutions and qualities simultaneously with different Codecs Support various communication protocols Supports TCP IP UDP RTP RTSP email and FTP protocols as well as various internet protocols such as ARP HTTP HTTPS and DHCP Web Browser based Monitoring Using the Internet web browser to display the image in a local network environment MAIAUSAO Alarm If an event occurs the event related video will be transferred to the FTP email specified by the user or saved to the SD memory or the event signal will be sent to the ALARM OUT port Intelligent Video Analysis Analyzes the event video according to the user specified rules to recognize the event ONVIF Spec 1 01 Compliance This product supports ONVIF Core Spec 1 01 O N Vi F For more information refer to www onvif org Driving network video through global standardization RECOMENDED PC SPECIFICATIONS CPU Pentium4 2 4GHz or higher Operating System Windows XP VISTA 7 Mac OS Resolution 1280X1024 pixels or higher RAM 1GB or higher Web Browser Internet Explorer 7 0 or higher Firefox Google Chrome Safari Video Memory 128MB or higher English _9 overview WHAT S INCLUDED Please check if your camera and accessories are all included in the product package User Manu
33. a scheduled time regardless of the actual occurrence of the event 1 From the Setup menu select the lt Event E gt tab 2 Click lt Time Schedule gt To set the timer event 1 Set lt Timer Event Setup gt to Enable 2 Specify the lt Activation time gt e Always Always sends an image at the set interval e Only scheduled time Periodically transfers image only at a specified time and date 3 Specify the lt Transfer interval gt 82_ setup screen 4 Specify the activation conditions e FTP Sending Specify the use of the FTP transfer if an event occurs e Record Specify the use of recording if an event occurs 5 When done click Apply SYSTEM SETUP Product Information 1 From the Setup menu select the Click lt Product information gt Check the camera information or lt System E gt tab N3JY0S dNLAS provide details according to your network environment e Location Specify the location where the camera is installed e Description Provide detailed information about the camera location e Memo Provide an explanation about the camera for better understanding e Language Select a preferred language for the camera menus and the Web Viewer OSD When done click Apply Date amp Time 1 2 Click lt Date amp Time gt 3 Specify the time and date that will be From the Setup menu select the lt System E gt tab applied t
34. al IP Installer DVD lt 7 poe ff Power Adapter Used for connecting to the power source Jack Modular LAN cable gender Cable for the testing Used to test the camera connection to a portable display device monitor Alarm Cable Used to connect to Alarm 1 0 lt f bA i O Template 1 Product installation guide Cu S A wh Used for fixing to an iron plate Dustproof Plate 1 Preventing dust inflow 10_ overview Model Name SNB 5000 SND 5080 5080F SNV 5080 SND 5080 5080F SNV 5080 SND 5080F SNV 5080 SND 5080 5080F SND 5080 C Mount Adapter Auto Iris Lens Used to install the camera lens Connector Camera Holder Used to install the camera holder SNB 5000 Mount Camera Holder Mount Screws Used to install the mount MAIAdSAO Used for installation on the wall or Ceiling L Wrench Used to remove fix the dome cover SNV 5080 For fixing a screw Inserted in a hole reinforced anchoring force Yee kasa H SND 5080F Ey bs Bracket Safety Lens Options not included FR Optional lens to be inserted in a SNB 5000 camera RS l 4 The Test Monitor Cable is connected to a portable displayer and used for testing the camera If you intend to use it for an actual monitoring camera use the BNC cable instead Plastic Anchor English _11 Overview AT A GLANCE SNB 5000 Front Side Item Description Camera Holder Used when you mount the camera o
35. an select a profile type in lt Video Profile gt under the lt Audio amp Video gt setup menu To capture the snapshot 1 Click EE on the scene to capture The Capture dialog should appear 2 Click Save button The screenshot will be saved in the specified path YAMAIA GAM bo Fiep B E hired de Bee imap Fite tee USING OSD SCREEN MENU To toggle the audio sound 1 Click the Audio Jj button The corresponding button will be displayed in the Viewer 2 Click the button to listen to mute the sound as you wish This button operates as a toggle button To toggle the microphone sound 1 Click the Mic button The corresponding button will be displayed in the Viewer 2 Click the button to start stop talking This button operates as a toggle button Click the microphone button that pops up on the screen to display the Silver light installation screen To fit the full screen 1 Click the Full Screen JJ button The corresponding button will be displayed in the Viewer 2 Click the button This will fit the Viewer to the full screen 3 To exit the full screen mode press Esc on the keyboard English _67 web viewer PLAYBACK 1 Click the Playback button 2 Specify the start time and end time of your search 3 Select a search type 4 Click the Search EEJ button The search results will be displayed in the list 5 Select a dat
36. any other pertinent obligations then as a consequence you may not distribute the Program at all For example if a patent license would not permit royalty free redistribution of the Program by all those who receive copies directly or indirectly through you then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Program If any portion of this section is held invalid or unenforceable under any particular circumstance the balance of the section is intended to apply and the section as a whole is intended to apply in other circumstances It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims this section has the sole purpose of protecting the integrity of the free software distribution system which is implemented by public license practices Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system it is up to the author donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License 8 If the distribution and or use of the Program is restricted in certain countries either by patents or by copyrighted i
37. are and 2 offer you this license which gives you legal permission to copy distribute and or modify the software Also for each author s protection and ours we want to make certain that everyone understands that there is no warranty for this free software If the software is modified by someone else and passed on we want its recipients to know that what they have is not the original so that any problems introduced by others will not reflect on the original authors reputations Finally any free program is threatened constantly by software patents We wish to avoid the danger that redistriobutors of a free program will individually obtain patent licenses in effect making the program proprietary To prevent this we have made it clear that any patent must be licensed for everyone s free use or not licensed at all The precise terms and conditions for copying distribution and modification follow TERMS AND CONDITIONS FOR COPYING DISTRIBUTION AND MODIFICATION 0 This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed under the terms of this General Public License The Program below refers to any such program or work and a work based on the Program means either the Program or any derivative work under copyright law that is to say a work containing the Program or a portion of it either verbatim or with modifications and or translated
38. ase Installing the camera 1 Hold down the bottom lock lever while removing the cover with the other hand a is Removing the cover reveals the main unit and inner cover 24_ installation amp connection 2 To fix the camera position hold down either hook of the inner cover and lift it up If this doesn t work use the hole on the bottom of the bracket to turn the bracket in the lt LOCK gt direction 4 Use the provided screws x8 to fix the bracket to a desired position ceiling or wall Ensure that the lt CAMERA FRONT gt label on the bracket faces the direction for camera monitoring 3 Push the release lock out while turning the main unit in LZ 2bBEFws the lt UNLOCK gt direction to remove the bracket NOILOANNODO 8 NOILVTIVLSNI 5 Arrange the cables through the bracket to the ceiling or wall If you drill a hole in the ceiling cover for wiring press hard to remove the cover and attach the dust proof plate to it and arrange the cables through the plate If you intend to arrange the cables without drilling a hole use the empty area opposite to the lt CAMERA FRONT gt label side for the wiring purpose 6 Mount the main unit onto the bracket Align the marking hole of the main unit with the Wiring Cover lt CAMERA FRONTS label of the bracket and turn the unit in the lt LOCK gt direction 7 Adjust the lens in a desired direction For adjusting the lens direction refer to Ad
39. ask gt of the camera e Gateway The lt Local IP Address gt of the IP router will be the lt Gateway gt of the camera 4 The settings may differ depending on the connected IP router model For more information refer to the user manual of the applicable router If not using an IP router For setting lt IP Address gt lt Subnet Mask gt and lt Gateway gt contact your network administrator 4 In the lt Port gt pane provide necessary information ne TAA ee e HTTP Port Used to access the a ae a camera using the Internet browser Subnet Mask defaulted to 80 Use the spin button to change the HTTP Port value sacra e VNP Port Used to control the video signal transfer defaulted to 4520 5 Enter the password This is the login password for the admin user who accesses the camera The default password is 4321 6 Click OK Manual network setup will be completed 7 When the manual setup including lt IP gt is completed the camera will restart 48_ network connection and setup If the IP router has more than one camera connected Configure the IP related settings and the Port related settings distinctly with each other Category Camera 1 Camera 2 IP Address 192 168 1 200 192 168 1 201 IP related settings Subnet Mask 255 255 259 0 255 255 255 0 Gateway 192 168 1 1 192 168 1 1 HTTP Port 10000 Port related settings VNP Port 4530 4 m f the lt HTTP Port gt is set other tha
40. ble router Applications amp Gaming Settings are successful English _51 dN13S ANY NOILOANNOO MYOMLAN network connection and setuo CONNECTING TO THE CAMERA FROM A SHARED LOCAL PC 1 Launch lt IP Installer gt It will scan for connected cameras and display a list of them 2 Double click a camera to access The Internet browser starts and con nects to the camera 4 m You can also access the camera in such way you type the IP address of the found camera in the address bar of the Internet browser CONNECTING TO THE CAMERA FROM A REMOTE PC VIA THE INTERNET As a remote PC can not directly access lt IP Installer gt you should access the camera in the IP router network using DDNS URL of the camera 1 Before you can access a camera in the IP router network you should have set the port range forward for the IP router 2 From the remote PC launch the Internet browser and type the DDNS URL address of the camera or the IP address of the IP router in the address bar ex http Awww samsungipolis com Product ID 52 network connection and setup camera setup HOW TO USE THE MENU KEY Follow the steps below if you run the Web Viewer for setting the menus 1 Launch the Web Viewer 2 Click Camera Menu EE in the left corner of the Live screen The camera setup menu appears 3 Use the Up Down 4 buttons to move to a desired item dNLAS VHANVO 4 To change the value of
41. cense D Give prominent notice with the combined library that part of it is a work based on the Library and explaining where to find the accompanying uncombined form of the same work 6 Revised Versions of the GNU Lesser General Public License The Free Software Foundation may publish revised and or new versions of the GNU Lesser General Public License from time to time Such new versions will be similar in spirit to the present version but may differ in detail to address new problems or concerns Each version is given a distinguishing version number If the Library as you received it specifies that a certain numbered version of the GNU Lesser General Public License or any later version applies to it you have the option of following the terms and conditions either of that published version or of any later version published by the Free Software Foundation If the Library as you received it does not specify a version number of the GNU Lesser General Public License you may choose any version of the GNU Lesser General Public SAMSUNG TECHWIN gP SALES NETWORK SAMSUNG TECHWIN CO LTD 701 Sampyong dong Bundang gu Seongnam si Gyeonggi do Korea 463 400 TEL 82 70 7147 8771 8 FAX 82 31 8018 3745 SAMSUNG TECHWIN AMERICA Inc SAMSUNG TECHWIN EUROPE LTD 1480 Charles Willard St Carson CA 90746 UNITED STATES Samsung House 1000 Hillswood Drive Hillswood Business Tol Free 1 877 213 1222 FAX 1 310 6
42. creen Video Setup T Click lt Video Setup gt Select a lt Video Source gt mode From the Setup menu select the lt Audio amp Video E gt tab e Flip Mode Turn upside down the image that is captured by the camera e Mirror Mode Flip horizontal the image that is captured by the camera Click the input box of each item in lt Privacy Area Configuration gt and enter select a desired value You can set up to 12 privacy zones Set the lt Video Output gt f you select lt OFF gt the video signal will not be output via the VIDEO OUT port When done click Apply To set the privacy zone You can specify a certain area of the camera video to be protected for your privacy Set it to lt Enable gt Place the cursor at a point in the video Specify the lt Color gt that will fill the To cancel your selection simply click and drag it to whatever you need privacy area Clear When done click Apply 72_ setup screen Audio Setup You can configure the I O settings of the audio source from the camera 1 From the Setup menu select the lt Audio amp Video EJ gt tab 2 Click lt Audio Setup gt 3 Adjust the audio I O levels to your preference e Audio In Set the audio input value e Audio Out Set the audio output value 4 When done click Apply NA3aYOS dNLAS NETWORK SETUP Interface 1 From the Setup m
43. e Mode MAC Ethernet Address gt amp amp IP Address 5 Protocol Description Model name of the connected camera Click the column to sort the list by model name However search will be stopped if clicked during the search Displays either lt Static gt or lt Dynamic gt for the current network connection status Ethernet address for the connected camera Click the column to sort the list by Ethernet address However search will be stopped if clicked during the search IP address Click the column to sort the list by IP address However search will be stopped if clicked during the search The factory default is 192 168 1 100 Network setting for the camera The factory default is IPv4 Cameras with the IPv6 setting will be displayed IPv6 46_ network connection and setup 6 UPnP Status This function is not currently implemented DDNS URL address enabling access from the external Internet URL However this will be replaced with the lt IP Address gt of the camera if DDNS registration has failed 8 IPv4 Scans for cameras with the IPv4 setting 9 IPv6 Scans for cameras with the IPv6 setting 10 Beart scans for cameras that are currently connected to the network cist However this button will be grayed out if neither IPv4 nor IPv6 is checked 11 Auto Set lt IP Installer gt will automatically configure the network settings for you 12 Manual Set You should configure the network
44. e direction of the arrow shown in the diagram SAMSUNG SD SYSTEM POWER O a English _33 Installation amp connection w Do not insert the SD memory card while it s upside down by force Otherwise it may damage the SD memory card Removing an SD Memory Card Gently press down on the exposed end of the memory card as shown in the diagram to eject the memory card from the slot SAMSUNG SD SYSTEM POWER SS Oy 34_ installation amp connection NOILOANNODO 8 NOILVTIVLSNI Pressing too hard on the SD memory card can cause the card to shoot out uncontrollably from the slot when released To remove the SD memory card set lt Record gt to OFF from lt SD Record gt and press Apply page 78 If you saved data in the SD memory card removing the SD memory card will cause damage to the data stored in the card lf the SD memory is inserted the SD LED indicator on the rear of the camera will turn on lf there occurs a problem in the SD memory the SD LED indicator will blink English _35 Installation amp connection MEMORY CARD INFORMATION NOT INCLUDED What is a memory card The memory card is an external data storage device that has been developed to offer an entirely new way to record and share video audio and text data using digital devices Selecting a memory card that s suitable for you Your camera supports SDHC memory cards You may however exper
45. e gains of the camera video manually SPECIAL e AWC SET Corrects the colors of the EXIT camera video to be optimized to the current lighting condition and screen mode You may need readjustment if the lighting condition is changed Put the focus of the camera to a white paper and press the Enter button e OUTDOOR Automatically corrects the video colors of the camera to be optimized to the outdoor environment e INDOOR Automatically corrects the video colors of the camera to be optimized to the indoor environment 2 To adjust it manually select lt MANUAL gt 3 Specify the lt RED gt and lt BLUE gt values as necessary BLUE RETURN 4 When completed select lt RETURN gt to return to the previous screen 54_ camera setup Custom Backlight Setup You can specify a desired area on the video manually and set the area to be displayed more clearly A V gt lt gt gt ENTER gt A V lt gt gt ENTER 1 Move to lt BACKLIGHT gt 2 Select lt BLC gt MAIN SUP SDR ON WE BAL NW gt BACKLIGHT BLC 4 POSURE SPECIAL EXIN 3 Set the BLC lt LEVEL gt You can change the level to adjust the BLG SETUP brightness of the monitoring area sit LEVEL LOW 4 Set the lt TOP BOTTOM LEFT RIGHT gt TOP levels to specify the target area 5 When completed select lt RETURN gt to return to the previous screen RETURN English _55 dNLAS VHANVO camera se
46. e is connected to 2 Connect the AUDIO OUT port of the camera with the LINE IN port of the speaker 3 Check the specifications for audio input Audio Codec G 711 PCM u law 64kbps 8kHz sampling Full duplex Audio e Audio in Used for mono signal line input Max 2 4 Vpp Audio out Used for mono signal line output Max 2 4 Vjp Line out impedance 6000 Alarm I O Wiring Diagram ALARM IN 5mA sink ALARM OUT 0VDC 2A 125VAC 0 5A MAX ALARM COM 40_ installation amp connection Connecting to the I O port box Connect the Alarm I O signal to the corresponding port of the rear port box 6 AUDIO OUT AUDIO IN SD CARD O SD SYSTEM POWER i O O VIDEO RESET 12345 NETWORK 86 1 ALARMIN 4 2 ALARM OUT 5 GND ALAM Le i 3 ALARM COM ALARM COM ACT NOILOANNODO 8 NOILVTIVLSNI 54321 LUPLPUPU O 1 ALARMIN 4 2 ALARM OUT 5 GND 3 ALARM COM SOON unLocK lt SND 5080 SND 5080F SNV 5080 gt ALARM IN Used to connect the alarm input signal e ALARM OUT Used to connect the alarm output signal ALARM COM Common port where the alarm output signal is connected e GND Used for earth grounding English _41 network connection and setuo You can set up the
47. e this is to make it free software which everyone can redistribute and change under these terms To do so attach the following notices to the program It is safest to attach them to the start of each source file to most effectively convey the exclusion of warranty and each file should have at least the copyright line and a pointer to where the full notice is found one line to give the program s name and an idea of what it does Copyright C yyyy name of author This program is free software you can redistribute it and or modify it under the terms of the GNU General Public License as published by the Free Software Foundation either version 2 of the License or at your optionjany later version This program is distributed in the hope that it will be useful but WITHOUT ANY WARRANTY without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE See the GNU General Public License for more details You should have received a copy of the GNU General Public License along with this program if not write to the Free Software Foundation Inc 51 Franklin Street Fifth Floor Boston MA 02110 1301 USA Also add information on how to contact you by electronic and paper mail If the program is interactive make it output a short notice like this when it starts in an interactive mode Gnomovision version 69 Copyright C year name of author Gnomovision comes with ABSOLUTELY NO WARRANT
48. ectronic shutter of the camera MANUAL Adjust the shutter speed of the camera manually A FLK This will prevent the screen from flickering e AGC Specify how to adjust the level according to the luminance MANUAL Adjust the screen brightness manually e SSNR Adjust the noise reduction level RETURN Sos LEVEL SETUP RETURN English _57 dNLAS VUANVO camera setup e SENS UP Automatically senses the darkness level at night or in a low contrast SENSU UMIT SETUR scene and extends the accumulation time gt LIMIT accordingly for a bright and sharp image RETURN m f you set the shutter mode to MANUAL FLICKERLESS SENS UP mode will be deactivated m The greater the video accumulation factor is the brighter the screen is but the afterimage of a moving object grows accordingly AUTO Set the work condition to Auto mode in a low contrast scene 3 When completed select lt RETURN gt to return to the previous screen Screen Display Setup You can specify the camera title and the OSD color that will be displayed on the screen A gt lt gt gt ENTER gt A V gt lt gt gt ENTER 1 Select lt SPECIAL gt MAIN Sur SSD ON Wale BEYNE AAW BACKUGHU ORF POSURE gt SPECIAL 4 EXIT 2 Select lt CAM TITLE gt SPECAL SETUP gt CAM TITLE OSD COLOR DYNAN Kedah IAA AD REMURN 58_ camera setup 3 Use alphanumeric characters in the list and enter a
49. em using the DHCP protocols If IPs are assigned by the internal DHCP server via the LAN Checking the dynamic IP 1 From a local PC run lt IP Installer gt to display a list of cameras that are assigned lt Dynamic IP gt 2 Select a camera in the list and click Manual Set to check the lt Dynamic IP gt of the camera If you uncheck lt DHCP gt you can change lt IP gt or lt Port gt to lt Static gt M bdr MTP Pn E MAC Address M NP Po IP Adrien 1 Ii i Fil Suaa St SS ae adrans Pie le ob 7 50_ network connection and setup PORT RANGE FORWARD PORT MAPPING SETUP If you have installed an IP router with a camera connected you must set the port range forwarding on the IP router so that a remote PC can access the camera in it Manual Port Range Forwarding 1 From the Setup menu of the IP router select lt Applications amp Gaming gt lt Port Range Forward gt For setting the port range forward for a third party IP router refer to the user guide of that IP router Select lt TCP gt and lt UDP Port gt for each connected camera to the IP router Each port number for the IP router should match that specified in lt Netwoks gt lt IP gt from the camera s Setup menu When done click Save Settings Your settings will be saved 4 The settings may differ depending on the connected IP router model For more information refer to the user manual of the applica
50. enu select the lt Network E gt tab 2 Click lt Interface gt 3 Set the lt Interface gt and lt IPv6 Setup gt as necessary e IP Type Select an IP connection type Manual Specify the IP address Subnet Mask Gateway DNS1 and DNS2 PPPoE Specify the DNS1 DNS2 ID and password DHCP Specify the DNS1 and DNS2 f you set it to lt Manual gt you should specify the IP Subnet Mask Gateway DNS 1 amp 2 manually e MAC Address Shows the MAC address e P Address Displays the current IP address e Subnet Mask Displays the lt Subnet Mask gt for the set IP e Gateway Displays the lt Gateway gt for the set IP e DNS1 DNS2 Displays the DNS Domain Name Service server address e Pv6 Use Specify the use of IPv6 e Pv6 Address Obtains the IPv6 address to access the IPv6 network 4 When done click Apply English _73 Setup screen Port 1 From the Setup menu select the lt Network E gt tab 2 Select lt Port gt 3 Type in each item in the Port menu as necessary Neither the port range between 0 and 1023 nor port 3702 is available e HTTP port HTTP port used to access the camera via the web browser The default is 80 TCP e VNP Port Set a port used to transfer video signals with the Samsung protocols RTSP Port Used to transfer videos in the RTSP mode the default is 554 VIEWER Port Used to transfer videos to the Web Viewer the default is 45
51. er to fix it To add an alarm cable 1 For this first you should remove the dome cover from the housing 2 Pull out the protruding rubber bar as shown 3 This will reveal a hole in the place of the rubber bar through which you insert the cable and connect it to the alarm terminal on the PCB 4 Connect and arrange the necessary cables power video etc lest that they should be damaged or caught while installing the camera Then install the camera assembly in the reverse order of the disassembly 5 Adjust the lens in a desired direction and close the dome cover NOILOANNODO 8 NOILVTIVLSNI English _27 Installation amp connection INSTALLATION SNV 5080 Disassembling To connect the alarm in out the dome cover and lens cover are to be separated 1 Using the L wrench provided loosen 3 screws by turning them counterclockwise and separate the dome cover 2 Lift up the inner cover while gently pressing its both ends to separate it from the unit 28 _ installation amp connection Optional Accessories for Installation For your easier installation you can purchase appropriate optional accessories available 1 WALL MOUNT ADAPTOR SCX 300WM HANGING MOUNT SCX 300HM This adaptor is used when installing the dome camera onto a wall 2 CEILING MOUNT ADAPTOR SCX 300CM HANGING MOUNT SCX 300HM This adaptor is used when installing the dome camera on a concrete ceiling 3 POL
52. he monitor Connect the VIDEO port of the camera to the video input port of the monitor 4 m In the initial installation of the camera you can connect the camera to the monitor for checking the connection status You must set lt Video Output gt to lt ON gt before the display screen can be activated page 72 Connect the monitor test cable to the output port of the monitor Ethernet Connection Connect the Ethernet cable to the local network or to the Internet Power Supply Use the screwdriver to connect each line of the power cable to the corresponding power port of the camera w Be careful not to reverse the polarity when you connect the power cable You can also use a router featuring PoE Power over Ethernet to supply power to the camera 4 The instructions above are also applied to SND 5080 SND 5080F SNV 5080 38_ installation amp connection Connecting to Audio Input Output Microphone SAMSUNG SD SYSTEM POWER DD O olo Tia o ul NOILOANNODO 8 NOILVTIVLSNI 2 0 0 e MLE Amp Microphone English _39 Installation amp connection 1 Connect the AUDIO IN port of the camera with the microphone directly or LINE OUT port of the amplifier that the microphon
53. ic License is intended to guarantee your freedom to share and change free software to make sure the software is free for all its users This General Public License applies to most of the Free Software Foundation s software and to any other program whose authors commit to using it Some other Free Software Foundation software is covered by the GNU Lesser General Public License instead You can apply it to your programs too When we speak of free software we are referring to freedom not price Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software and charge for this service if you wish that you receive source code or can get it if you want it that you can change the software or use pieces of it in new free programs and that you know you can do these things To protect your rights we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights These restrictions translate to certain responsibilities for you if you distribute copies of the software or if you modify it For example if you distribute copies of such a program whether gratis or for a fee you must give the recipients all the rights that you have You must make sure that they too receive or can get the source code And you must show them these terms so they know their rights We protect your rights with two steps 1 copyright the softw
54. ience compatibility issues depending on the model and make of the memory card For your camera we recommend you use a memory card from the following manufacturers SDHC SD Memory Card Sandisk Transcend Kingston Your camera supports 2GMB to 32GB of memory card capacity Playback performance can be affected depending on the speed of memory card so use the high speed memory card To ensure proper recording of video data we recommend you use a memory card that supports at least read write soeed 10Mbps and Class 6 Memory Card Use SD and SDHC memory cards feature a switch that disables writing data on to the media Having this switch to the Lock position will prevent accidental deletion of data stored in the memory card but at the same time will also prevent you from writing data on to the media Memory Card Components Contacts Lock Switch SD SDHC 36_ installation amp connection CONNECTING WITH OTHER DEVICE Monitor SD SYSTEM POWER A A C RESET O NETWORK T Network Monitor Out J Monitor x Network English _37 NOILOANNODO 8 NOILVTIVLSNI Installation amp connection Connecting to t
55. ion to avoid injury from tip over Unplug this apparatus during lighting storms or when unused for A long periods of time Refer all servicing to qualified service personnel Servicing is required when the ap paratus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped 2_ overview WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS PROCUCT TO RAIN OR MOISTURE DO NOT INSERT ANY METALLIC OBJECT THROUGH THE VENTILATION GRILLS OR OTHER OPENNINGS ON THE EQUIPMENT Apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids such as vases shall be placed on the apparatus CAUTION MAIAdSAO RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL EXPLANATION OF GRAPHICAL SYMBOLS The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the
56. is inserted in the proper direction Operation of memory card that is formatted by other devices is not guaranteed with this camera unit e Format the memory card again in lt Setup gt gt lt Event gt gt lt SD Record gt menu e Check if the write protection tab of the memory card is set to Lock GPL LGPL SOFTWARE LICENSE This product uses some Software programs which are distributed under the GNU GPL General Public License LGPL license and the program is licensed as is without warranty of any kind The program can be obtained from us for a period of three years after our last distribution of this product by sending email to help cctv samsung com If you want to obtain the complete Corresponding Source Code in the physical medium such as CD ROM by airmail the cost of physically performing source distribution might be charged This offer is valid to anyone in receipt of this information For more additional information visit http Awww samsungsecurity com gp e GPL Software linux kernel busybox GNU GENERAL PUBLIC LICENSE Version 2 June 1991 Copyright C 1989 1991 Free Software Foundation Inc 51 Franklin Street Fifth Floor Boston MA 02110 1301 USA Everyone is permitted to copy and distribute verbatim copies of this license document but changing it is not allowed Preamble The licenses for most software are designed to take away your freedom to share and change it By contrast the GNU General Publ
57. just the focus and turn the knob clockwise to lock the focus Using the test monitor cable you can connect to a mobile display for camera test AT A GLANCE SNV 5080 Appearance Item 1 Dome Cover 2 Main unit 3 Power Port 4 Video Out Port 5 Network Port 6 Audio In Jack 7 Audio Out Jack MAIAdSAO k ff ene Description Dome cover for the lens and unit protection Main unit includes the lens switch board PCB boards and screws Used to plug the power cable Video signal output port connected to the monitor Used to connect a PoE or LAN cable Used to connect to a microphone Used to connect to speakers English _21 overview Inside Se Tee x HH 7 UNLOCK j 3 Item Description ALARM IN Used to connect the alarm input signal Abani Gut ALARM OUT Used to connect the alarm output signal me ALARM COM Common port where the alarm output signal is co
58. justing the monitoring direction for the camera page 31 8 Secure the inner cover to the main unit Fit the two holes of the wing side locks on the inner cover into the corresponding hole of the main unit and press it down until you hear a click 9 Fix the cover to the main unit Fit the protruding part inside the cover into the corresponding hole of the main unit and turn the cover to fix it English _25 Installation amp connection INSTALLATION SND 5080F Removing the dome cover 1 Hold down the bottom lock lever while removing the cover with the other hand Removing the cover reveals the main unit and inner cover 2 To fix the camera position hold down both hooks of the inner cover while lifting it up Ceiling Mount 1 Use the provided template to drill one hole for the camera and one for the screw 5 mm in diameter at least 35 mm in depth and insert the plastic anchor HUR 5 to the end of the screw hole 2 Connect and arrange the necessary cables power video etc lest that they should be damaged or caught while installing the camera 26_ installation amp connection 3 Insert the camera assembly into the hole so that it fits to the camera hole and fix the assembly using the assembly screw tappings TH M4xLS0 x3 4 Close the dome cover 5 Fix the cover to the main unit Fit the protruding part inside the cover into the corresponding hole of the main unit and turn the cov
59. l transfer the alarm images Port The default port of the FTP server is 21 however you can use a different port number according to the FTP server settings Passive Mode Select lt On gt if you need to connect in passive mode due to the firewall or the FTP server settings H q k 4 as a English _77 Setup screen e Email Configuration Server Address Enter the IP address of the email server that you use for the email transfer ex SMTP hotmail com User ID Enter the user ID for logging into the email server Password Enter the user account password for logging into the email server Port The default port of the email server is 25 however you can use a different port number according to the email server settings Recipient Enter the address of the email recipient Sender Enter the address of the email sender If the sender address is incor rect the email from the sender may be classified as SPAM by the email server and thus may not be sent Subject Enter a subject for your email Body Provide the text for the massage Attach the alarm images to the email that you are preparing 4 When done click Apply SD Record You can set the record conditions or the use of recording for the SD memory check the size of stored data or format the SD memory itself 1 From the Setup menu select the lt Event E gt tab 2 Click lt SD Record gt 78_ setup screen To make
60. lick Save The backup file will be saved to the specified path in the format of bin Restore English _85 Setup screen 4 Select a backup file and click Open Log You can check the system log or event log 1 From the Setup menu select the lt System E gt tab 2 Click lt Log gt 3 Select a log type e Syslog You can check the system logs where any system changes are recorded including the time information e Evtlog You can check the event logs including the time information 4 From the right log list select an item to search for e f you select lt All gt in the top left dropdown list all logs for the applicable log type will be displayed 5 If one page can not display all the logs available use the bottom buttons to move to the previous next or the last item 4 m f you want to view the details of a log click lt Description gt in the right column of the log the log information will be shown in the bottom pane m Each page displays 15 logs with the latest one displayed at the top The event system log list can contain up to 1000 logs after that the existing logs will be deleted from the oldest one each time a new log is created 86_ setup screen aooendx CAMERA SPECIFICATION Items Description Camera Type Color BW Color Device 1 3Mega Pixel Progressive Scan CMOS Size 1 3 inch Image Scan Progressive Scan Pixels Total 1 384 H x 1 0
61. llowed only for noncommercial distribution and only if you received the program in object code or executable form with such an offer in accord with Subsection b above The source code for a work means the preferred form of the work for making modifications to it For an executable work complete source code means all the source code for all modules it contains plus any associated interface definition files plus the scripts used to control compilation and installation of the executable However as a special exception the source code distributed need not include anything that is normally distributed in either source or binary form with the major components compiler kernel and so on of the operating system on which the executable runs unless that component itself accompanies the executable If distribution of executable or object code is made by offering access to copy from a designated place then offering equivalent access to copy the source code from the same place counts as distribution of the source code even though third parties are not compelled to copy the source along with the object code 4 You may not copy modify sublicense or distribute the Program except as expressly provided under this License Any attempt otherwise to copy modify sublicense or distribute the Program is void and will automatically terminate your rights under this License However parties who have received copies or rights from you
62. lor mode during normal daytime and switches to black and white mode in a low contrast scene Target at night RETURN Press the Enter button to adjust the switching interval between the two modes m f you set the AGC mode to OFF from lt EXPOSURE gt the AUTO DAY NIGHT mode will be disabled accordingly DWELL TIME This is the time while each applicable lighting condition is WNC AUTO SETUP kept in order to enable the switch between day and night modes ee 3 DURATION Adjust the brightness of RETURN the lighting where the mode switch occurs e COLOR Always displays the video in colors e BW Always displays the video in black and white 3 When completed select lt RETURN gt to return to the previous screen 60_ camera setup Image Adjustment You can configure the sharpness gamma level and color settings of an image to your preference A Y gt lt gt gt ENTER gt A V gt lt gt gt ENTER 1 Select lt SPECIAL gt MAIN SETUP SSD ON Wilts BAL ATW BACKUGHI OFF POSUns gt SPECIAL EXIT dNLAS VJJNWVO 2 Select lt IMAGE ADJ gt SPECIAL SzTUP CAM Wiis OFF OSD COLOR Wilts DANICH AWO gt IMAGE ADJ RETURN 3 Select each item and set it appropriately If selecting lt SHARPNESS gt you can IMAGE SETUP adjust the sharpness of the image e SHARPNESS Adjust the overall sharp GAMMA ness of the image COLOR Haa The higher the level is the sharper RET
63. mm 125 H x160 O mm 134 5 H x160 2 mm Physical Weight Net 4380 525g 765g 1 3409 Specification Color Body Dark Grey White Case Metal Plastic Aluminum IP66 88_ appendix NETWORK SPECIFICATION Items Description 0S Embedded Linux Flash memory 128M byte RAM 206M byte Network Ethernet RJ 45 10 100BASE 1 Board Hardware Video Out VBS 1 0Vp p Audio Line In Line Out SD Memory Slot Yes SD SDHC m PoE Yes IEEE802 3af Class 2 z Input 1 ea eal Output 1 ea Relay Compression H 264 MPEG4 MJPEG Multiple Codec SXGA 1280x1024 HD 16 9 1280x720P Resolution SVGA 800x600 VGA 640x480 QVGA 320x240 max rrame nae o Gace 30ins Compression 1 20 20 steps Video Target Bitrate CBR mode only 1280x1024 1024 10240 kbps H 264 MPEG4 Quality 1280x720 1024 10240 kbps 800x600 512 5120 kbps 640x480 512 5120 kbps 320x240 64 2048 kbps MJPEG Quality 1 20 level Bitrate Control ve ie VEREEN Streaming H 264 MPEG4 MJPEG multiple streaming Individual streaming simultaneously Compression G 711 u law Audio EEEE SENT Bi Directional Communication Yes oa Intelligent Motion Detection Sey ieee pear English _89 aooendx Items Description IP IPv4 IPv6 TCP IP UDP IP RTP UDP RTP TCP RTSP NTP Network IPv4 HTTP HTTPS SSL DHCP FTP SMTP ICMP IGMP Protocol SNMPv1 v2c
64. n 80 you must provide the lt Port gt number in the address bar of the Internet browser before you can access the camera ex http IP address HTTP Port http 192 168 1 201 10000 Auto Network Setup Run lt IP Installer exe gt to display the camera search list At the initial startup both Auto Set and Manual Set will be grayed out O For cameras found with the IPv6 setting these buttons will be grayed out as the cameras do not support this function 1 Select a camera in the search list Find the MAC Ethernet address labeled on the rear of the camera Both the Auto Set and Manual Set buttons will be activated 2 Click Auto Set The Auto Setting dialog appears The lt IP Address gt lt Subnet Mask gt and lt Gateway gt will be set automatically 3 Enter the password Auto Setting This is the login password for the Network Information admin user who accesses the IP Address camera The default password is SSHRC 4321 Gateway 4 Click OK Auto network setup will be completed Iv IP Setting m Password 5 The camera will automatically complete the network setting and restart English _49 dN13S ANY NOILOANNOO MYOMLAN network connection and setuo DYNAMIC IP SETUP Dynamic IP Environment Setup e Example of the dynamic IP environment If an IP router with cameras connected is assigned an IP address by the DHCP server If connecting the camera directly to mod
65. network settings according to your network configurations CONNECTING THE CAMERA DIRECTLY TO LOCAL AREA NETWORKING Connecting to the camera from a local PC in the LAN 1 Launch an Internet browser on the local PC 2 Enter the IP address of the camera in the address bar of the browser INTERNET Firewall DDNS Server Data Center KOREA Local PC lt Local Network gt 4 A remote PC in an external Internet out of the LAN network may not be able to connect to the camera installed in the intranet if the port forwarding is not properly set or a firewall is set In this case to resolve the problem contact your network administrator 42_ network connection and setup CONNECTING THE CAMERA DIRECTLY TO A DHCP BASED DSL CABLE MODEM INTERNET E DSL Cable gt External Remote PC Modem Camera DDNS Server Data Center KOREA as Use the cross LAN cable to connect the network cable directly to your PC N Run the IP Installer and change the IP address of the camera so that you can use the web browser on your desktop to connect to the Internet Use the Internet browser to connect to the camera dN13S ANY NOILOANNOO MYOMLAN Move to Setup page Move to Network DDNS and configure the DDNS settings Move to Network Interface and set the network type to DHCP Connect the camera which was removed f
66. nnected GND Used for earth grounding AD Memory Gary Compartment for the SD memory card Compartment Resets the camera settings to the default Press and hold it for about 5 seconds to turn off the system indicator and restart the system 3 Reset Button E Resetting the camera requires reconfiguration of network settings IP address subnet mask gateway address etc using the IP Installer software application 22_ overview Components Item 1 Inner Cover 2 Side wing hooks 3 ZOOM lever MAIAUSAO Description Cover for the main unit s protection By lifting it while gently pressing the both ends you can separate the inner cover Turn the barrel left or right to adjust the zoom and turn the knob clockwise to lock the zoom Turn the barrel left or right to adjust the focus and turn the knob clockwise to lock the focus Using the test monitor cable you can connect to a mobile display for camera test English _23 Installation amp connection INSTALLATION SND 5080 Precautions before installation Ensure you read out the following instructions before installing the camera e Select an installation site ceiling or wall that can endure at least 5 times of the camera weight e Stuck in or peeled off cables can cause damage to the product or a fire e For safety purposes keep anyone else away from the installation site And put aside personal belongings from the site just in c
67. nterfaces the original copyright holder who places the Program under this License may add an explicit geographical distribution limitation excluding those countries so that distribution is permitted only in or among countries not thus excluded In such case this License incorporates the limitation as if written in the body of this License 9 The Free Software Foundation may publish revised and or new versions of the General Public License from time to time Such new versions will be similar in spirit to the present version but may differ in detail to address new problems or concerns Each version is given a distinguishing version number If the Program specifies a version number of this License which applies to it and any later version you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation If the Program does not specify a version number of this License you may choose any version ever published by the Free Software Foundation 10 If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different write to the author to ask for permission For software which is copyrighted by the Free Software Foundation write to the Free Software Foundation we sometimes make exceptions for this Our decision will be guided by the two goals of preserving the free status of all derivatives of our f
68. nto the bracket by fixing the camera Mount Holes holder mount adaptor with the bracket Auto Iris Lens 2 Optional Installed on the lens adaptor Auto Iris Lens Connector Used to supply power and output signal to control the iris of the lens 4 Wipe out a dirty surface of the lens softly with a lens tissue or cloth to which you have applied ethanol 12 overview Rear Side Lege 9 NETWORK ET iii MAINHJAO ALARMIN 4 ALARM OUT 5 GND ALARM COM Item SD Memory Card Compartment AUDIO OUT 2 Audio terminal AUDIO IN System Power SD Indicators SYSTEM POWER ACT Description Compartment for the SD memory card Terminal for audio output Terminal for audio input ON A memory card is inserted and operates normally Flashing Failed to record insufficient space or inserted abnormally OFF Camera is off camera is restarting or memory card is not in place ON The camera is turned on and connected to the network properly Blinking During DDNS setup or in case of setup failure or in a state of unstable network connection OFF When the system is rebooting or turned off ON While the power is on OFF If the power is off English _13 overview Reset Button Power Port GND Sia amp Network Port 5 1 0
69. o the camera e Current system time Displays the current time settings of your system Timezone Specify the local time zone based on the GMT Use Daylight Saving Time If checked the time will be set one hour before the local time zone for the specified time period This option will be displayed only in areas where DST is applied English _83 Setup screen e System time setup Specify the time and date that will be applied to your system Manual Specify the time manually Synchronize with NTP server Sync with the time of the specified server address Synchronize with PC viewer Synchronize the time with the connected PC 4 When done click Apply User 1 From the Setup menu select the lt System E gt tab 2 Click lt User gt 3 Provide the necessary user information e Administrator Password Change Change the current password for the administrator Guest setup If lt Guest access gt is permitted any guest can access the Web Viewer screen but can view only the Live viewer screen e Current Users You can change the user information and adjust the permission level for a user who is set to lt Enable gt Video You can select a video profile in the Liver viewer screen Audio In The audio input option will be activated in the Live Viewer screen Controls You can configure the camera menus and control the use of the alarm button 4 When done click Apply Upg
70. oring cannot connect to the system using a tab browser of Internet Explorer 7 0 The camera connected to the network is not detected in the IP installer program SOLUTION e Check to make sure that the camera s Network settings are appropriate e Check to make sure that all network cables have been connected properly e f connected using DHCP verify that the camera is able to acquire dynamic IP addresses without any problem e f connected using a DDNS URL verify that the MAC address has been properly entered e f the camera is connected to a router verify that port forwarding is properly configured e Connected Viewers become disconnected upon any change to camera or network configurations e Check all network connections e f the camera is connected over an PPPoE network it s possible for Viewer to disconnect under poor network conditions e When you try to connect to the system using a tab browser the same cookie information is shared resulting in errors when connected Therefore instead of using a tab browser open a new browser window to connect to the system e Turn off the firewall settings on your PC and then search the camera again Images overlap e Check whether two or more cameras are set to a single multicast address instead of different addresses If a single address is used for multiple cameras the images may overlap No image appears e f the transmission method is set
71. presence of important operating AN and maintenance servicing instructions in the literature accompanying the product Class I construction An apparatus with CLASS I construction shall be connected to a MAINS socket outlet with a protective earthing connection Battery Batteries battery pack or batteries installed shall not be exposed to excessive heat such as sunshine fire or the like English _3 overview Disconnection Device Disconnect the main plug from the apparatus if it s defected And please call a repair man in your location When used outside of the U S it may be used HAR code with fittings of an approved agency is employed CAUTION These servicing instructions are for use by qualified service personnel only To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so The BNC output port is used to monitor the installation process of the network camera If you Keep the BNC cable connected a risk of lightening may cause damage or malfunction to the product 4 overview Please read the following recommend safety precautions carefully Do not Place this apparatus on an uneven surface Do not place this apparatus near OF Ze Do not install on a surface where it is exposed to direct sunlight near heating equipment or heavy cold area Do not attempt to service this apparatus yourself 7
72. rade Reboot 1 From the Setup menu select the lt System E gt tab 2 Click Upgrade Reboot 3 Select a desired item and set it appropriately e Upgrade Performs upgrading the system 84_ setup screen 4 To perform the upgrade 1 4 m f you forcibly terminate the upgrade Click Upgrade 2 Click Send The UPGRADE dialog appears where upaa e Factory default Resets the system to the factory default Except network parameter Reset the other settings except for the interface port DDNS IP filtering settings All Resets all settings including the camera settings however the log information will not be reset f you reset all settings the IP address will be defaulted to 192 168 1 100 e Configuration backup amp Restore Backs up the current system settings before performing the restoration process e Restart Restarts the system When done click Apply N3aYOS dNLAS Click Browse and specify a file to upgrade the progression will be shown in the Downloading was surceeded Rewind am riire bottom iea Upgrading wes started Kaal upor b ng w i dco Appiesuss ungrading was succeeded process upgrade will not be completed properly To save the current settings and restore the backup settings Click Backup Specify the backup path with a proper To restore the backup settings click The Save As dialog should appear file name and c
73. recording on the SD memory 1 Check the lt Total Size gt and the lt Free Size gt 2 If the SD memory has a sufficient free space set lt Record gt to On 3 Specify the record conditions Otherwise check the stored data and if you find them not important then click lt Format gt to format the SD memory f your SD memory card writes slowly only one frame per second will be stored For a SD memory card with a large capacity the formatting will be slowed down accordingly Note that only one frame per second 1 fps will be stored for the following resolutions 1280x1024 1280x720 800x600 Ifthe size of data grows with time only 1 fps can be stored even if you set the record quality to Full Frame N3aYOS dNLAS e Record 1 fps forcibly Only one frame per second will be recorded regardless of the existing record profile Overwrite If the SD memory is full this will delete old data and store new data in replacement Pre alarm duration Specify the time point before the occurrence of the alarm starting from the time point the images will be transferred You can specify up to 5 seconds before the occurrence of the alarm e Post alarm duration Specify the time point after the occurrence of the alarm to the specified time point the images will be transferred You can specify up to 120 seconds after the occurrence of the alarm 4 When done click Apply Alarm Input You can set the alarm input
74. ree software and of promoting the sharing and reuse of software generally NO WARRANTY 11 BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE THERE IS NO WARRANTY FOR THE PROGRAM TO THE EXTENT PERMITTED BY APPLICABLE LAW EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND OR OTHER PARTIES PROVIDE THE PROGRAM ASIS WITHOUT WARRANTY OF ANY KIND EITHER EXPRESSED OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU SHOULD THE PROGRAMPROVE DEFECTIVE YOU ASSUME THE COST OF ALL NECESSARY SERVICING REPAIR OR CORRECTION 12 INNO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER OR ANY OTHER PARTY WHO MAY MODIFY AND OR REDISTRIBUTE DAMAGES INCLUDING ANY GENERAL SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES END OF TERMS AND CONDITIONS How to Apply These Terms to Your New Programs If you develop a new program and you want it to be of the greatest possible use to the public the best way to achiev
75. rom your PC directly to the modem O N OO FB W Restart the camera l4 For registering the DDNS settings refer to DDNS page 74 For configuring the DDNS settings refer to Registering with DDNS page 76 For setting the network type refer to Interface page 73 English _43 network connection and setuo CONNECTING THE CAMERA DIRECTLY TO A PPPOE MODEM a External Remote PC Camera DDNS Server Data Center KOREA 1 Use the cross LAN cable to connect the network cable directly to your PC N Run the IP Installer and change the IP address of the camera so that you can use the web browser on your desktop to connect to the Internet Use the Internet browser to connect to the camera Move to Setup page Move to Network DDNS and configure the DDNS settings Move to Network Interface and set the network type to PPPoE Connect the camera which was removed from your PC directly to the modem O N OO FB WO Restart the camera l4 For registering the DDNS settings refer to DDNS page 74 For configuring the DDNS settings refer to Registering with DDNS page 76 For setting the network type refer to Interface page 73 44_ network connection and setup CONNECTING THE CAMERA TO AN IP ROUTER WITH THE PPPOE CABLE MODEM This is for a small network environment such as homes SOHO and ordinary shops INTE
76. s to provide customers with more environmentally friendly products The Eco mark represents Samsung Techwin s devotion to creating environmentally friendly products and indicates that the product satisfies the EU RoHS Directive Correct Disposal of This Product Waste Electrical amp Electronic Equipment Applicable in the European Union and other European countries with separate collection systems This marking on the product accessories or literature indicates that the product and its electronic accessories e g charger headset USB cable should not be disposed of with other household waste at the end of their working life To prevent possible harm to the environment or human health from uncontrolled waste disposal please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources Household users should contact either the retailer where they purchased this product or their local government office for details of where and how they can take these items for environmentally safe recycling Business users should contact their supplier and check the terms and conditions of the purchase contract This product and its electronic accessories should not be mixed with other commercial wastes for disposal CONTENTS OVERVIEW INSTALLATION amp CONNECTION NETWORK CONNECTION AND SETUP 2 9 9 10 12 15 18 21 24 26 28 32 33 36 37 42 44 4
77. t being bound by section 3 of the GNU GPL 2 Conveying Modified Versions If you modify a copy of the Library and in your modifications a facility refers to a function or data to be supplied by an Application that uses the facility other than as an argument passed when the facility is invoked then you may convey a copy of the modified version a under this License provided that you make a good faith effort to ensure that in the event an Application does not supply the function or data the facility still operates and performs whatever part of its purpose remains meaningful or b under the GNU GPL with none of the additional permissions of this License applicable to that copy 3 Object Code Incorporating Material from Library Header Files The object code form of an Application may incorporate material from a header file that is part of the Library You may convey such object code under terms of your choice provided that if the incorporated material is not limited to numerical parameters data structure layouts and accessors or small macros inline functions and templates ten or fewer lines in length you do both of the following a Give prominent notice with each copy of the object code that the Library is used in it and that the Library and its use are covered by this License b Accompany the object code with a copy of the GNU GPL and this license document 4 Combined Works You may conve
78. the files and the date of any change b You must cause any work that you distribute or publish that in whole or in part contains or is derived from the Program or any part thereof to be licensed as a whole at no charge to all third parties under the terms of this License c If the modified program normally reads commands interactively when run you must cause it when started running for such interactive use in the most ordinary way to print or display an announcement including an appropriate copyright notice and a notice that there is no warranty or else saying that you provide a warranty and that users may redistribute the program under these conditions and telling the user how to view a copy of this License Exception if the Program itself is interactive but does not normally print such an announcement your work based on the Program is not required to print an announcement These requirements apply to the modified work as a whole If identifiable sections of that work are not derived from the Program and can be reasonably considered independent and separate works in themselves then this License and its terms do not apply to those sections when you distribute them as separate works But when you distribute the same sections as part of a whole which is a work based on the Program the distribution of the whole must be on the terms of this License whose permissions for other licensees extend to the entire whole
79. tible with the Linked Version e Provide Installation Information but only if you would otherwise be required to provide such information under section 6 of the GNU GPL and only to the extent that such information is necessary to install and execute a modified version of the Combined Work produced by recombining or relinking the Application with a modified version of the Linked Version If you use option 4d0 the License ever published by the Free Software Installation Information must accompany Foundation the Minimal Corresponding Source and If the Library as you received it specifies that Corresponding Application Code If you a proxy can decide whether future versions ace a eto of the GNU Lesser General Public License 2 shall apply that proxy s public statement specified by section 6 of the GNU GPL for of acceptance of any version is permanent conveying Corresponding Source authorization for you to choose that version 5 Combined Libraries for the Library You may place library facilities that are a work based on the Library side by side in a single library together with other library facilities that are not Applications and are not covered by this License and convey such a combined library under terms of your choice if you do both of the following a Accompany the combined library with a copy of the same work based on the Library uncombined with any other library facilities conveyed under the terms of this Li
80. tions As used herein this License refers to version 3 of the GNU Lesser General Public License and the GNU GPL refers to version 3 of the GNU General Public License The Library refers to a covered work governed by this License other than an Application or a Combined Work as defined below An Application is any work that makes use of an interface provided by the Library but which is not otherwise based on the Library Defining a subclass of a class defined by the Library is deemed a mode of using an interface provided by the Library A Combined Work is a work produced by combining or linking an Application with the Library The particular version of the Library with which the Combined Work was made is also called the Linked Version The Minimal Corresponding Source for a Combined Work means the Corresponding Source for the Combined Work excluding any source code for portions of the Combined Work that considered in isolation are based on the Application and not on the Linked Version The Corresponding Application Code for a Combined Work means the object code and or source code for the Application including any data and utility programs needed for reproducing the Combined Work from the Application but excluding the System Libraries of the Combined Work 1 Exception to Section 3 of the GNU GPL You may convey a covered work under sections 3 and 4 of this License withou
81. tup HLC Highlight Compensation Setup When a strong light such as streetlamp or headlight faces forward to the camera you can mask that exposed area in order to protect it from being saturated A Y gt lt gt gt ENTER gt A V gt lt gt gt ENTER 1 Select lt BACKLIGHT gt 2 Select lt HLC gt MAN SETUP SSOR ON WAS EYAL NAW gt BACKLIGHT HLC gs POSURE SPECIAL EXI 3 Set the lt LEVEL gt and the lt MASK TONE gt nue SsyUP e LEVEL Adjust the brightness level so as to remove the incoming highlight N TONE 7 from a specific condition RETURN e MASK TONE Adjust the mask tone of the highlighted area 4 When completed select lt RETURNS gt to return to the previous screen 4 At night operation this function will be activated only if the highlight comes from more than a certain area in a dark environment At night operation HLC will not function in too a bright or too a dark scene 56_ camera setup Exposure Setup You can adjust the exposure level of the camera A gt ENTER gt 4 lt gt gt ENTER gt 4 lt gt gt ENTER 1 Move to lt EXPOSURE gt and select a setting value MAIN SETUP SSD Walle EYAL BACKEIGH ih SPECIAL EXIT 2 Select each item and set it appropriately e BRIGHTNESS Adjust the screen POSURE SETUP brightness e IRIS If set to lt MANUAL gt you can adjust the iris of the camera manually e SHUTTER Adjust the el
82. type activation time and operation mode 1 From the Setup menu select the Click lt Alarm input gt Specify an input device lt Event E gt tab e Normal Open It is normally open but if it is closed an alarm will be triggered e Normal Close It is normally closed but if it is open an alarm will be triggered Specify the lt Activation time gt e Always Always activates when an alarm occurs e Only scheduled time Activates at a specified day of the week for a specified time period The start time should be earlier than the end time both of which are different with each other English _79 Setup screen 5 6 Specify an operation that will perform if an alarm occurs e Output duration Specify the alarm output time in the alarm input setup e E mail Sending Specify the use of email transfer in the alarm input setup e Record Specify the use of recording in the alarm input setup When done click Apply Video analysis 1 Click lt Video analysis gt Specify the use of Intelligent Video Specify the use of overlay Specify the object size Select a sensitivity level at which the Select an event rule Specify the activation time and activation From the Setup menu select the lt Event E gt tab Analysis If you set it to Enable the event rules will be shown on the screen camera detects the object You can select a total of
83. under this License will not have their licenses terminated so long as such parties remain in full compliance You are not required to accept this License since you have not signed it However nothing else grants you permission to modify or distribute the Program or its derivative works These actions are prohibited by law if you do not accept this License Therefore by modifying or distributing the Program or any work based on the Program you indicate your acceptance of this License to do so and all its terms and conditions for copying distributing or modifying the Program or works based on it Each time you redistribute the Program or any work based on the Program the recipient automatically receives a license from the original licensor to copy distribute or modify the Program subject to these terms and conditions You may not impose any further restrictions on the recipients exercise of the rights granted herein You are not responsible for enforcing compliance by third parties to this License If as a consequence of a court judgment or allegation of patent infringement or for any other reason not limited to patent issues conditions are imposed on you whether by court order agreement or otherwise that contradict the conditions of this License they do not excuse you from the conditions of this License If you cannot distribute so as to satisfy simultaneously your obligations under this License and
84. variable one for the compression type f you set the resolution to 1280X1024 the maximum frame rate is 22 fps N3aYOS dNLAS Target bitrate Specify the bit rate at which you will transfer the video Encoding priority You can set the video transfer method to Framerate or Compression GOP size Select a GOP size between 1 and 15 Profile The H 264 profiling method is fixed to lt HIGH gt Entropy coding Reduce the possible compression loss due to encoding Multicast VNP Specify the use of the VNP protocol Pv4 Enter an IPv4 address with which you can connect to the IPv4 network Port Specify the video communication port TTL Set the TTL for the VNP packet Multicast RTP Specify the use of the RTP protocol Pv4 Enter an IPv4 address with which you can connect to the IPv4 network Port Specify the video communication port TTL You can set the TTL for the RTP packet What is GOP size GOP Group of Pictures is a set of video frames for MPEG4 and H 264 format compression indicating a collection of frames from the initial Frame key frame to the next I Frame GOP consists of 2 kinds of frames Frame and P Frame Frame is the basic frame for the compression also known as Key Frame which contains one complete image data P Frame contains only the data that has changed from the preceding I Frame You can set between 1 and 15 for the MPEG4 and H 264 CODEC English _71 Setup s
85. y a Combined Work under terms of your choice that taken together effectively do not restrict modification of the portions of the Library contained in the Combined Work and reverse engineering for debugging such modifications if you also do each of the following a Give prominent notice with each copy of the Combined Work that the Library is used in and that the Library and its use are covered by this License b Accompany the Combined Work with a copy of the GNU GPL and this license document c For a Combined Work that displays copyright notices during execution include the copyright notice for the Library among these notices as well as a reference directing the user to the copies of the GNU GPL and this license document d Do one of the following Convey the Minimal Corresponding Source under the terms of this License and the Corresponding Application Code in a form suitable for and under terms that permit the user to recombine or relink the Application with a modified version of the Linked Version to produce a modified Combined Work in the manner specified by section 6 of the GNU GPL for conveying Corresponding Source 1 Use a suitable shared library mechanism for linking with the Library A suitable mechanism is one that a uses at run time a copy of the Library already present on the user s computer system and b will operate properly with a modified version of the Library that is interface compa

SNV-5080 User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents