User Manual - Data Display Group
Contents
1. please use only commercially available screen cleaner Do not spray the cleaner directly to the device but onto a cloth Please clean ventilation slots regularly to ensure a good air circulation Protect your device from water splash When cleaning please make sure that no liquids get into the device screens and surfaces can be easily scratched Therefore please use the prescribed cloth only Caution high voltage Never open the device by yourself In case of unusual noises burnt smell or smoke unplug the power cable Do not insert objects into the device through the ventilation slots If the same picture is displayed over a longer period of time an after image may arise When exchanging batteries pay attention to the polarity Keep batteries away from children and ensure an environmentally correct disposal First Installation 5 First Installation Position of connectors and controls All the connectors for power and cables are located at the bottom of the back side of the display The OSD keyboard is located left on the back side back view Position of the keys of the gt OSD menus in the Video Sefies Position of additional USB ports option only Position of the connectors for power and signal cables Mounting with VESA compliant monitor brackets VESA mounting points The SLIM line monitors have an integrated VESA mounting The operating position of the device is perpendicular 90 degrees to the fl2. 68 cm 27 The POS Line monitors are offered in different screen sizes and with various controllers and other options Important note This user manual is complemented by other additional documents when indicated All documents are also available for download from Data Display Group web site www datadisplay group com SLIM Line monitor versions SLIM Line Video P ECOIII Monitor with integrated AD converter board 1 x RGB 1 x DVI SLIM Line Video PIII Monitor with integrated AD converter board 1 x RGB 1 x DVI S Video Composite Video 2 Chassis Versions For SLIM line monitors are available as version with additional USB ports This implies a deviation in the housing form Options such as glass or touch screen does not change the external appearance Version with extra USB ports on the back sideview OSD Front view Scope of Delivery d Scope of Delivery When unpacking the monitor please check if the following accessories are included in the shipment a Note Pictures can differ from actually supplied products CD inclusiv User Manual Data Sheets Drawings User manual Accompanying CD Manuals E Power supply Datasheets Driver Drawings RGB cable USB cable Power cable Devices with touch sensor only Cable may vary depending on country General Safety Regulations 4 General Safety Regulations Safety information Please read this safety in
3. DCDi Main MADI Mode Film Mode Detection Off Film Display Mode Normal 3 2 Aspect Ratio Full Screen PIP Tiling 22 Advanced Video Processing Sub Menu Main DCDI Turns DCDi on off on main channel MADI Mode Changes Motion Adaptive De Inter lacing among normal off adaptive modes Advanced Film Mode Sub Menu Detection Selection of Video 3 2 Video 2 2 Video 3 2 2 2 off Mode Selection of Normal 3 2 or other future modes Display Settings Ment Aspect Ratio Used to adjust display among full screen panoramic letter box expand pillar box and 1 1 PIP PIP sub menu Tiling Tiling sub menu SLIM Line Video PIII PIP Picture in Picture Sub Menu PIP mode Toggle between Off PAP Tall Side PIP Mode by Side Small PIP and Large PIP ni Vertical Vertical position of PIP image l Horizontal Horizontal position of PIP image Horizontal Transparency Transparency of PIP image Transparency Tiling Sub Menu for video walls Horizontal Total Defines the total horizontal number Horizontal Total of displays vertical Total Vertical Total Defines the total vertical number of displays Horizontal Position F ME r oe Horizontal Position Defines the horizontal position of Vertical Position the actual display unit Tiling Status Vertical Position Defines the vertical position of the actual display unit Tiling Status Enables disables the tiling function If the PIP Mode i
4. HE optimum image quality input pixels should be sampled at the ideal Advanced sampling points Clocks Line Slider to adjust the sample clock of the analogue interface This is help ful for improving the image quality for non standard display modes Advanced Advanced Settings sub menu Advanced Settings Sub Menu Note This function can be used to manu ally force some of the widely used difficult to detect modes which can ah eee fat be misinterpreted by the controller 1050 60HzZ 1400 350 f 40070 f S5HzZ 640 2 Video Video Horizontal Vertical Blend Time Out Horizontal Flip Vertical Flip Rotation Ole Zoom Factory Reset Speed Mode Show Menu Of Input Search Auto Brightness Main Input RGB CS Pip Input RGB CS Firmware Version ISD Version oo 0 E 0 0 0 SLIM Line Video PIII Advanced Settings Sub Menu HDMI mode only OSD Settings Menu Horizontal Vertical Blend Time Out Horizontal Flip Vertical Flip Rotation OSD Zoom Setup Menu Factory Reset Speed Mode Show Menu Of Input Search Auto Brightness Firmware Version OSD Version Move the OSD in horizontal direc tion Move the OSD in vertical direction OSD transparency adjustment This function determines after how many seconds the OSD will close itself Flips the OSD horizontally Flips the OSD vertically Rotates OSD Changes OSD size Ex
5. of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense Canadian Department of Communications Compliance Statement This Class A digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations Observation des normes Class A Cet appareil num rique de la classe B est conforme a la norme NMB 003 du Canada FCC Information e Changes or modifications not expressly approved by Distec GmbH could void the user s authority to operate the equipment e Use the attached specified cables with the POS Line monitor so as not to interfere with radio and television reception e Please use the supplied power cord or equivalent to ensure FCC compliance e Please use the supplied shielded video signal cable Mini D SUB 15 pin to Mini D SUB 30
6. requirements of the European Directives was proved by the application of the following harmonised Standards Main Unit EMV NSR RoHS Year of CE marking RF Unit displays with WLAN only R amp TTE NSR EN 55022 2010 AC 2011 EN 55024 2010 EN 61000 3 2 2006 A1 2009 A2 2009 EN 61000 3 3 2008 EN 60950 1 2006 A11 2009 A1 2010 AC 2011 A12 2011 EN 50581 2012 2013 EN 301 489 1 V1 9 2 2011 09 EN 301 489 17 V2 2 1 2012 09 EN 300 328 V1 8 1 2012 06 EN 60950 1 2006 A11 2009 A1 2010 AC 2011 A12 2011 29 Declaration of Conformity Exposition von Personen EN 62479 2010 RoHS EN 50581 2012 The object of the declaration described above is in conformity with Directive 2011 65 EU of the European Parliament and of the Council of 8 June 20110n the restriction of the use of certain hazardous substances in electrical and electronic equipment Germering 19 12 2013 Werner Schubert Gesch ftsf hrung FCC Declaration of conformity This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commer cial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation
7. 201503_Manual_SLIM_Line_EN User Manual SLIM Line Series DATA DISPLAY GROUP SLIMLine industrial monitors Germany www datadisplay group de Europe www datadisplay com A SLIM Line monitors for 48 3 cm 19 and 58 4 cm 23 D DATA DISPLAY GROUP Copyright The contents of this manual are subject to change without notice 2015 Data Display Group All rights reserved Reproduction of this manual in parts or entirely without the previous authorization of Data Display Group is prohibited Data Display Group is not liable for errors and collateral or subsequent damage which result from supply deployment or any other utilisation of this document All product names mentioned in this document are trademarks or registered trademarks of their due owners 2 Table of Contents 1 2 General SDC HG ALONG aaa rane 4 CIS 4 SCOPO ira 5 General Safety Regulations oo ccccecececesessesesesestsctesesestterereatitneenestene 6 IRPI iii 9 TOUCH SENSOFS 12 SLIM Line Video P ECOII 13 SIVE 1 E EA 17 Maintenance ce cccececseseseeeecscsesesecseseseececssseseessessseeecesseseneeasenees 26 Guarantee Service 0 26 39165 PREC RR RO EDT 28 LEG ANA AOD CON MONI RR A ORTA 29 General Specifications 1 General Specifications Scope of Document This user manual is valid for POS Line monitors up to
8. and direction rotate flip Reset all settings to factory defaults Reset all color settings to factory defaults Reset all position settings to factory defaults Adjust image sharpness set DOS modes 640 720 Exit Leave sub menu ao oe 2 oe tS Press keys to select sub menu Press menu key to go to sub menu SLIM Line Video PIII 0 SLIM Line Video PIII Connectors and OSD buttons of POS Line Video PIII series OSD Keyboard optional Power supply Composite Video USB Touch sla Connecting to a PC with VGA cable VGA RGB O Connecting to a PC with DVI cable Connecting to a PC with DVI HDMI cable SLIM Line Video PIII Connecting to an external device with S Video cable Ti paa Connecting to an external device with Composite Video cable GIO A N N RRR aAa IT 000 DT Il Composite Video Composite Video USB Touch USB o L 18 SLIM Line Video PIII OSD keyboard The OSD functions of the monitor can be controlled via OSD key pad The OSD allows the selection of the input source and the fine tuning of various functional param
9. be connected to a low power source according to EN60950 1 chapter 2 5 Low Power Source Caution The power source for POS Line monitors with 12V DC operating power must not exceed the limit of 250 VA e Make sure that your external power supply is sufficient for the display The maximum power consumption of the display is indicated in the data sheet and the display label 11 6 Touch Sensors SLIM Line monitors are available with touch option Depending on the panel size different touch systems and touch technologies are used If the monitor has been ordered with touch option the touch sensor and touch controller are installed at factory SLIM Line Video The drivers for these monitors must be installed on your PC system HID devices do not need drivers for Windows 7 and 8 Please contact our support center if you are using LINUX based computers If a driver is required the touch on this driver must be calibrated Is it a HID Touch Windows calibration in the control panel must be performed Anzeige Sonstiges Konfigurieren Konfigurieren Sie den Bildschirm fur die Stift und Toucheingabe Anzeigeoptionen Anzeige 1 HP Compaq L2105tm LCD Breitbildm Y Details Unterstutzung f r eingeschrankte Toucheingabe Kalibrieren 6 Zur cksetzen gedreht wird Zur Ausrichtung wechseln Wahlen Sie die Reihenfolge aus in der der Bildschirm path Control Panel All Control Panel Ite
10. ble and which includes but is not limited to the following e Unauthorized opening or disassembling of the product e Faulty maintenance by non observation of maintenance instructions e inappropriate storage or cleaning of the product e Unauthorized modification of the product e Incorrect use or misuse e Non observation of operating and installation instructions e Permanent display of fixed images causing image retention or image sticking e Operating the product in conditions which exceed the limitations of the specification e Use of inappropriate boxes packaging or modes of shipment e Force majeure like fire acts of war acts of violence chemical or biological impacts lightning strikes over voltage or similar events e Fault resulting from the use of software which was not originally supplied with the product or which is incorrectly installed e Normal wear and tear and wearing parts i e LCD panel Mechanical damages like scratches pressure or break points are excluded from this guarantee This guarantee does not include accessory parts which are not integral part of the product as boxes batteries Pixel errors only constitute a fault under the terms of this guarantee If they deviate from the product specification i e ISO 9241 307 pixel failure class Il 26 Guarantee Service Display Quality Prevention of after image burn in effects After image burn in means that an image or part of an image i e logo remain
11. ecute factory reset In graphics mode fast image trans fer is supported Changes the menu between main image and PIP if the PIP mode is on Toggles input search on off Optional Toggles automatic bright ness control through external light sensor on off Installed Firmware Version Installed OSD Version 25 Maintenance 9 Maintenance Systems with active cooling require cleaning of ventilation slots every 6 months Systems with passive cooling must be cleaned every 12 months 10 Guarantee Service Guarantee Data Display Group grants a manufacturer s guarantee of two years from the date of delivery The rendering of guarantee claims shall neither extend nor restart the guarantee period During the guarantee period Data Display Group shall repair product faults based on material or production defects The guarantee service is executed at Data Display Group s discretion through repair replacement of defective parts or by exchanging a product for a product of equal quality without charging the customer for material or labor Guarantee claims are only accepted if Data Display Group receives notification of a defective product within the guarantee period and the product is presented to the Data Display Group Service Centre together with all information as specified in the RMA process Guarantee Exclusions and Limitations This guarantee does not apply to any defect for which Data Display group is not responsi
12. ely guarantees that the product is free of material and manufacturing faults Data Display Group does not issue any other guarantee or similar statements other than this declaration This guarantee does not impair or affect a buyer s statutory claim against the seller due to material damage Such claims can be as serted instead of the guarantee agreed to here at the buyer s discretion Mandatory legal rights and mandatory claims under the German Product liability remain unaffected Applicable Law and Place of Jurisdiction The laws of the Federal Republic of Germany apply Place of jurisdiction is Munich 2 Disposal Service addresses Germany England USA Distec GmbH Display Technology Ltd Apollo Corp Augsburger Str 2b 5 The Oaks Business Village 87 Raynor Avenue Unit 1 D 82110 Germering Revenge Road Lordswood Ronkonkoma NY 11779 49 0 89 89 43 63 0 Chatham Kent MED 8LF 1 1 631 580 4360 lt support distec de 44 0 16 34 67 27 55 2 info apollodisplays com x info displaytechnology co uk Please go to the following web address for further information about our RMA regulations and RMA forms Http www datadisplay group com service 11 Disposal Disposal of old devices If the acquired Distec product is to be disposed of must be implemented into national law the Directive 2012 19 EU Disposal of batteries Applicable in all countries of the EU and in countries with separate battery co
13. ent Advanced Advanced Open Advanced sub menu Reset Scheme Advanced Image Settings Menu Note Noise Reduction Video Processing and Film Mode amp Scaling are only available for RGB S Video and Noise Reduction Composite signals Color Video Processing Film Mode amp Scaling SLIM Line Video PIII Advanced Color Sub Menu Color Temp Allow selection of different color Color Temp temperature schemes Selections are user SRGB 4200K 5000K einen atk 5400K 6500K 7200K 9300K DI PrAUon User Color Create custom color scheme ADC Auto Color Adjust Performs auto fine tuning on the ADC RGB S Vid eo and Composite only Advanced User Color Sub Menu Red Gain Boost adjustment on red Red Gain Green Gain Boost adjustment on green Green Gain Blue Gain Boost adjustment on blue Blue icain Red Offset Offset level on red Green Offset Offset level on green Red Offset Blue Offset Offset level on blue Green Offset Blue Offset Advanced Noise Reduction Sub Menu CCS Mode Changes Cross Color Suppression CCS Mode between off adaptive normal Dynamic NR Changes Dynamic Noise Reduction between low medium high off adaptive High setting may cause loss of detail adjust for best image MPEG NR Enables disables the MPEG NR Mode MPEG NR Manual setting of MPEG noise reduction level Dynamic NR Mode 5 0 MPEG NR Mode MPEG NR 21 SLIM Line Video PIII Main
14. ersons who are qualified to activate ground and label devices systems and circuits according to the safety standards Operation For a proper and safe utilization of the product adequate transportation storage installation assembly careful handling and main tenance are essential The device is only certified for in door operation Extreme ambient conditions shall be avoided and the monitor shall be protected from dust humidity and heat Do not expose the monitor to direct sunlight Transport Unpack the monitor at the place of installation Use only original packaging for transportation Please observe these rules for any later transport Condensation Avoid condensation during transport at low temperatures or at extreme fluctuations of temperature General Safety Regulations Safety guidelines for the handling of LCD monitors e f the device is not used for a long period of time unplug the power cable e Do not unplug the power cable while the device is powerd on except for emergencies e To unplug the device without problems sockets have to be easily accessible e Ensure that the power cable does not get pinched or kinked e Do not place heavy objects on the power cable e Do not use damaged or loose sockets to plug in the device e Plug the device in earthed sockets only e Operate the device with the power cables included in the delivery packet only e Use undamaged power cables only e When plugging in and
15. eters like brightness contrast etc OSD Keyboard 10 0 0 6 O 0 Power Menu Enter Up Down Left Right LED The six buttons of the OSD control can either be used e Jo access various functions directly e Jo navigate within the OSD The following two tables provide an overview of the functions Direct functions Down if PIP PAP is activated otherwice without function CSS CCI Navigation in OSD menu Pe pe Enter 19 SLIM Line Video PIII Left Reduce value of the slider if slider is selected Right Increase value of the slider if slider is selected The green red LEDs on the external keypad show the current status of the board CS CCI CSS CSI IE CSS CI I CSS CE IE Special functions of the controller e PIP Picture in Picture Simultaneous display of two video sources on the screen with adjustable positions e PAP Picture and Picture Side by side display of two video sources e Tiling Display of a video source on several monitors with mutually non overlapping frames OSD menu Image Settings Menu scheme Switches between normal sport Canene Spray game cinema vivid presettings Brightness Panel brightness adjustment Brightness Contrast Panel contrast adjustment Contrast Hue Panel HUE adjustment RGB SEIS S Video and Composite only Hue Saturation Panel saturation adjustment RGB Snipness S Video and Composite only Sharpness Panel sharpness adjustm
16. formation carefully for your personal safety and for the prevention of property damage In case of a malfunction immediately disconnect the power plug and contact your dealer or the next Data Display Group service cen tre A malfunction is also considered if the housing a control element or cable is damaged or if liquids or other objects penetrate the monitor Please read the safety information carefully before installing the device If you have any doubts about whether the device may be used in a particular environment please contact our service partner Repairs Repairs may only be carried out by authorized technical personnel Unauthorized access or improper repairs might cause serious prop erty damage or cause danger to the user In addition to that any legitimate warranty claim expires Electrical connection Disconnect the monitor from socket before executing any work Do not touch or connect data cables or power cables during thunder storms System start up Before the system start up let the monitor adjust to the room temperature Do not expose the device to direct heat sources In case of condensation please wait a minimum of 12 hours before switching on the monitor The monitor shall only be installed and used according to this documentation data sheets Only qualified personnel may perform the initial installation and system setup Qualified personnel Qualified personnel in terms of the safety information of this documentation are p
17. llection systems The Batteries in this product should not be disposed with other household waste The chemical symbol Pb CD or Hg indicate that the battery contains lead cadmium or mercury above the reference level in EC directive 2006 66 Batteries which are not disposed correctly can cause harm environment and health Our environment is close to our hearts Please help us to protect our environment and recycle empty batteries with the free battery collection system 28 Declaration of Conformity 12 Declaration of Conformity CE EC Declaration of Conformity Address Product Model Distec GmbH Augsburger Str 2B 82110 Germering Germany SLIM Line display series Video PECOIII Video PIII 19 0 DS 90 538 DS 90 539 DS 91 520 DS 91 339 DS 90 861 DS 90 862 DS 91 214 DS 91 215 D5 90 909 DS 31 393 23 0 DS 91 152 DS 91 185 DS 91 404 DS 91 228 DS 91 229 The product is in compliance with the requirements of the following European directives Main Unit 2004 108 EG 2006 95 EG 2011 65 EU RF Unit displays with WLAN only 1999 5 EG 2011 65 EU Electromagnetic Compatibility EMC Low Voltage Directive LVD Restriction of the use of certain hazardous substances in electrical and electronic equipment RoHS Radio and Telecommunications Terminal Equipment R amp TTE Restriction of the use of certain hazardous substances in electrical and electronic equipment RoHS The compliance with the
18. ms Tablet PC Settings Note All drivers for the touch sensors can be found on the enclosed CD The following table gives an overview over the touch systems including web addresses for driver downloads Touch system overview 4 wire resistive DMC 190A140A http www datadisplay group de service downloads touch treiber c9816 23 AMR elurbo SR HID device no driver required for Windows 30M182235D6 12 SLIM Line Video P ECOIII 1 SLIM Line Video P ECOIII Connectors of POS Line Video P ECOIII series optional lt OSD Keyboard Osos D gt enu Exit nc Tal LED optional Connecting to a PC with VGA cable o 9 Connecting to a PC with DVI cable USB Touch SLIM Line Video P ECOIII Connecting USB cable option to a PC or different devices with USB cable OSD keyboard OSD functions of the monitor can be controlled via OSD key pad The OSD allows selection of input source and fine tuning of various functional parameters like brightness contrast etc OSD Keyboard ORO OC Power Menu Exit The buttons of the OSD control can either be used e To access va
19. oor For wall mounting the permissible tilt angle is observed The device can be operated both in landscape mode and in portrait mode VESA formats 19 VESA 40 x 40 75 x 75 23 VESA 40 x 40 75 x 75 200 x 200 First Installation Allowed tilt angle for mounting SLIM line monitors can be mounted with the adjacent tilt angles monitor 0 to 180 0 to 180 tilt angle Connecting to Power Note All the POS Line monitors requiring 12V DC power are shipped with an appropriate power supply The power is connected to the display via the green female connector at the back side Specification of the power connector Female connector Phoenix Contact DFK MSTB 2 5 3 GF Male plug Phoenix Contact MSTB 2 5 3 STF Connecting to power with included power supply Note Connect the data cables to external devices before plugging the display to the power LAI EE SESS SS SS SEER SCS SS SS a e eo eo eo Power supply 10 First Installation All monitors with power supply have an adapter cable to connect the AC adapter This cable is included in the scope of dfelivery e Connect the adapter cable to the display e Connect the adapter cable to the 12 V connector of the power supply e Insert the power cable into the power supply e Connect the power cable to a power socket Connecting to an existing power supply Caution The SLIMLine monitors with 12V DC operating power must only
20. out do not touch the power cable with wet hands e Ensure that the power cable is plugged in the socket safely and correctly e Use for devices with external power supply only the supplied original power supply or an equivalent Low Power Source LPS e Do not use extension block to plug several devices into a single socket e According to the size devices may be difficult to handle and very heavy Ensure that at least two people lift and carry the device e Put down the device slowly and carefully to avoid damaging the LCD screen Ensure that the device stands stable e Keep packaging away from children Danger of suffocation e Use our specified and professionally mounted wall mounting only e Do not put objects onto the device e Do not place candles heaters or humidifier near the device e Keep the device away from fireplaces and flammable materials General Safety Regulations 8 Ensure sufficient ventilation of the device Keep a minimum distance of at least 10 mm devices to the wall for devices with inte grated PC of at least 40 mm Ensure compliance with the operating temperature Do not install the device in places where it is exposed to environmental impacts such as rain or direct sunlight Do not install the device in places where it is exposed to high humidity dust or smoke In case of doubt please contact your sales partner Please use a soft moist cloth for cleaning For cleaning the screen
21. rious functions directly e To navigate within the OSD The following two tables give an overview about the functions Direct functions CEE SS I CSS IE CEI IE CSS II 14 SLIM Line Video P ECOIII Navigation in OSD menu The LED show the current status of the board CS CCI CSS CSI IE fe free CSS CI I OSD menu Input Select 1024x768 100 Hz 1 Select VGA as input signal 2 Select DVI as input signal Exit Leave sub menu Press keys to select sub menu Press menu key to go to sub menu Input Select 15 SLIM Line Video P ECOIII 1024x768 100 Hz Brightness Contrast 1024x768 100 Hz Color ecs 1024x768 100 Hz a 1024x769 0100 Hz oa 16 Display Contrast 1 Adjust panel brightness 2 Adjust panel contrast Exit Leave sub menu Press keys to select sub menu Press menu key to go to sub menu Color 1 Perform automatic color adjustment 2 Set color space to sRGB 3 Adjust color temperature manually Exit Leave sub menu Press keys to select sub menu Press menu key to go to sub menu Image Perform automatic image optimization Adjust image width Adjust scanning spot of RGB signal Adjust image position in horizontal direction ae RI Adjust Image position in vertical direction Exit Leave sub menu Press keys to select sub menu Press menu key to go to sub menu Tools OSD adjustments for time out position
22. s PAP Tall or side by side the tiling status will be off and disabled Example 3 by 3 video wall Definition of horizontal vertical display position Position Note e Tiling property cannot be used while PAP Tall or Side by Side modes are active e f PIP is turned on the PIP image would be displayed on every panel of the video wall e mage and position menus are disabled while tiling Is on e For best results the Horizontal Total and Vertical Total value should to be set to a value which is an integer divider of the input width or height respectively For example if input is 1280x768 horizontal total has to be set to one of 2 4 5 8 and vertical total has to be set to one of 2 3 4 6 8 23 Position Settings Menu for HDMI S Video and Component Video Signals Width Adjusts total width of the image by stretching or shrinking Width Height i Height Adjusts total height of the image by Horizontal Start stretching or shrinking Vertical Start Horizontal Start Changes the starting point of the image horizontally without altering height Vertical Start Changes the starting point of the image vertically without altering width Position Settings Menu for RGB Auto Adjust Performs auto adjust function on the Auto Adjustment mae Image Position Image position sub menu Image Position gt Phase Slider to adjust the sampling phase Phase O kel of the analogue interface For Clonkevline
23. s visible on the screen even if the image on the screen is changed This should not occur if the LCD panel is operated in normal conditions with changing content To prevent burn in effects please follow the following guidelines e Do not display fixed patterns for an extended time period of more then 12 hours e Power off the monitor for 4 hours after using it for 20 hours and for 2 hours after using it for 12 hours e Use the power scheme and power management of the PC e Use plain colored screen savers e Avoid patterns with a strong difference in brightness and contrast e Avoid gray colors e Change images and logos regularly Show animated pictures for 60 seconds after 4 hours of operation e The best way to protect your display is to switch the monitor off when not in use or to use screen Savers Non observance of these guidelines may have effects on warranty Guarantee Processing Group RMA process In order to avoid unnecessary charges it is important to adhere to the RMA regulations Products must be appropriately and professionally packed for a safe return to the Data Display Group Service Centre Products with panel sizes equal or larger then 81 cm 32 must be shipped on pallets in upright position Data Display Group does not assume liability for any customer data stored on products which are returned to Data Display Group Limitations of Liability and Benefits With this guarantee declaration Data Display Group exclusiv
Download Pdf Manuals
Related Search