EBDSPIR-IP product guide
Contents
1. Ceiling mounted presence lectronics intelligent energy control C P Electronics Ltd Brent Crescent London NW10 7XR United Kingdom Tel 44 0 333 900 0671 Fax 44 0 333 900 0674 www cpelectronics co uk enquiry cpelectronics co uk Ref WD223 Issue 32. Wire the product using the connector using the diagram on the front page e To switch from more than one position simply wire two or more units in parallel e Mount as shown above e To maintain the IP rating the unit must not be used on ceilings with an uneven surface e Ensure that the unit is pushed tightly into place after commissioning e Set the LUX level to maximum a e Power the unit up the load sho e Vacate the room or remain very should take no more than 2 min e Check that the load switches on e To set the final LUX level wait ur enough that lighting is required wise at minimum very slowly t lights come on Note that when t lights will always come on with e Set the time required ae ss Fault Finding nd the time to minimum sld come on immediately still and wait for the load to switch off utes when movement is detected til the level of natural daylight is just Starting with the LUX control fully clock irn the control anti clockwise until the ne LUX control is at maximum then the ccupancy LOAD DOES NOT COME ON LIGHTS DO NOT GO OFF Ensure that the area is left unoccupied for longer than the selected timer setting Check to see if the live supply to the circuit is good Strap across the L and LIVE OUT terminal to turn the load on Make sure that the sensor is If the supply and wiring are not adjacent to circulating air good check the LUX level heaters or lamps setting Inc
3. Product Guide lectronics EBDSPIR IP Ceiling Presence Detector Sealed IP55 CIRCUIT PROTECTION IF REQUIRED LIVE NEUTRAL Overview The EBDSPIR series of presence detector switches are designed to provide automatic control of light ing heating or ventilation loads They detect movement using a PIR sensor and turn the load on When an area is no longer occupied the load will switch off after an adjustable time out period An adjustable internal light sensor provides additional energy saving in lighting applications When an area is occupied lighting is only switched on when the level of natural light is below a preset level When the unit is first powered up the PIR sensor will always detect immediately regardless of whether the room is occupied The IP variant of these products is sealed to IP55 when installed flush in a ceiling FLUSH FIXING Hole 64mm Warning be careful bending springs when mounting unit Installation e The detector should be sited so that the occupants of the room fall inside the detection pattern shown overleaf at a recommended height of 2 8m on the ceiling Note that the lower the sensor is installed the smaller the detection range will be subject to the parameters shown on the diagram e Avoid direct sunlight entering the sensor e Do not site within 1m of forced air heating or ventilation Do not site within 1m of any lighting e Do not fix to a vibrating surface e
4. rease the LUX level setting to allow the controller to turn on at higher ambient natu ral light level If the detection range is smaller than expected check the dia gram above Rotating the sen sor slightly may improve the range Detection Pattern Area of high sensitivity Areaof lower sensitivity Specification Part Numbers LOAD 8 Amp resistive and incandescent lighting 6 Amp fluorescent lighting 3 Amp compact fluorescent lighting 3 Amp low energy lighting 3 Amp low voltage lighting switch primary of transformer Fluorescent lighting max 6 fittings recommended For fluorescent lighting total power factor correction ca pacitance must not exceed 40uF 3 Amp fans and ventilation equipment Switch SON lighting loads via a contactor SUPPLY VOLTAGE 220 240 Volts AC 50 Hz TIME OUT PERIOD Adjustable 10s to 30m LIGHT LEVEL Light to dark TERMINAL CAPACITY 2 5 mm MATERIAL Flame retardant ABS TYPE Class 2 IP RATING IP55 TEMPERATURE 10 C to 35 C CONFORMITY EMC 89 336 EEC LvD 73 23EEC E IMPORTANT NOTICE This device should be installed by a qualified electrician in accordance with the latest edition of the IEE wiring regulations ESTA energy services and technology association FM 45789 Due to our policy of continual product improvement CP Electronics reserves the right to alter the specification of this product without prior notice EMS 534520 EBDSPIR IP
Download Pdf Manuals
Related Search