USER`S MANUAL
Contents
1. Special D Control device Description Application DO Device type to be displayed 1 For specified device DO 1 Device No to be displayed monitor function pee Dox Backlight OFF time min BOE pias backlight DO 3 Protects display screen 2 For protect function DO 4 Not available MO Requests edition of displayed device data For specified device MO 1 Edition completion response monitor function MO 2 Disables backlight OFF function For automatic backlight Turns on backlight forcedly OFF function MO 3 Displays or hides operation errors etc 3 Others MO 4 ESC key status 4 MO 5 key status 4 For specified device D8159 MO 6 key status 4 monitor function KO MO 7 OK key status 4 MO 8 Not available MO 9 Not available MO 10 Not available MO 11 Not available MO 12 Not available MO 13 Not available MO 14 Not available 1 Input numeric values correspond to the devices as follows 1 Input X 2 Output Y 3 Auxiliary relay M 4 State S 5 Timer T 6 Counter C 16 bit current value set value and 32 bit set value 7 Data register D 16 bit8 Data register D 32 bit 9 Time display 10 Counter C 16 bit current value set value and 32 bit current value 2 0 Enables all operations 1 Enables only the time display function 2 Enables only the monitor function 3 PC hardware errors parameter errors grammatical2. Press the key to increase the value Press the key to decrease the value Press the OK key to determine the input At this time the input data is written to the PLC lt Monitoring 32 bit D gt RUN D lt Changing the current value of 32 bit D gt gt gt p o 000 gt E E OK gt OK Dis scrolled by 2 points at a time by the key and by 1 point at a time by the key Select the current value change mode Press the key to increase the value Press the key to decrease the value Press the OK key to determine the input At this time the input data is written to the PLC lt Error display gt Error step No Error code m Croor mes Z Cm Press the ESC key or IOC m LIL release the error status to delete the error display This manual confers no industrial property rights or any rights of any other kind nor does it confer any patent licenses Mitsubishi Electric Corporation cannot be held responsible for any problems involving industrial property lt Keyword Entry code error display gt When an keyword entry code has been input to the PLC only the time can be displayed E m If you press the OK key while the time is displayed the error message CC OC shown on the left flickers for 5 seconds
3. RUN D C Ma Press the or key to change over the current value and the set value For the set value S is added in a S ID right position above the device No moanan When the OK key is pressed the current value or the set value is changed esto UUW Press the key to increase the value Press the key to decrease the value Set value Press the OK key to determine the input At this time the input data is written to the PLC When the OK key is pressed and held for 2 seconds or more while the current value is changed the current value is reset to 0 and the contact turns off When the OK key is pressed once again the current value reset operation will be completed lt Monitoring 16 bit D gt lt Changing the current value of 16 bit D gt RUN OK OK D p mann i IUU gt l m u D is scrolled by 1 point at a time Select the current value change mode Press the key to increase the value Press the key to decrease the value Press the OK key to determine the input At this time the input data is written to the PLC lt BFM unit selection gt S State v WE Y lt Buffer memory No selection gt BFM BFM lt Buffer mem
4. ACCE Release the keyword entry code in a peripheral unit such as the FX 10P 20P and the personal computer software for creating sequence programs Manual number JY992D84901 Manual revision E Date June 2008 afa MITSUBISHI ELECTRIC CORPORATION HEAD OFFICE TOKYO BUILDING 2 7 3 MARUNOUCHI CHIYODA KU TOKYO 100 8310 JAPAN HIMEJI WORKS 840 CHIYODA CHO HIMEJI JAPAN rights which may occur as a result of JY992D84901E Effective June 2008 using the contents noted in this manual Specifications are subject to change without notice Changes for the Better aa MITSUBISHI PROGRAMMABLE CONTROLLERS MELSEC F DISPLAY MODULE FX1n 5DM USER S MANUAL JY992D84901E This manual only describes the specifications for Display Module FX1N 5DM For complete operation wiring mounting and programming instructions please refer to the FX1S FX1N HARDWARE MANUAL and PROGRAMMING MANUAL These manuals should be read and understood before attempting to install or use the unit Related Manuals Manual name Manual No Description FX1S Series Hardware Describes contents related to hardware of FX1S Series Manual JY992D83901 PLC such as specifications wiring and installation It is offered with FX1S Series PLC basic unit FXiN Series Hardware Describes contents related to hardware of FX1N Series Manual JY992D88201 PLC such as specifications wiring and installation It
5. key key OK OK key Time display screen when the power is turned on RUN lt Setting the time gt I2 x Q 5 OK OK An item being changed flickers Snir 4 1 5 Pressandh id ae fe ral Set year month day hour and minute in this order etermine i umj u F gt LILI l it for 2 seconds the input When the OK key is pressed at minute set up the setting operation will be completed or more lt Selecting a device gt OK TCD ox To 1 gt XYMS 7 Determine z the input Program error Keyword error Entry code error Select an either device using the and keys In the initial status D flickers T C D 16 bit D 32 bit X Y M S or BFM Error display lt key key gt Refer to error display BFM is displayed only when the FX1n Series PLC is used lt Monitoring a bit device X Y M S gt lt Forced setting resetting a bit device Y M S gt gt D gt sk OK Di OK OK Y Ose Y zag B Set or reset the bit go asss j a e ae ae 4 a From the displayed device No the ON OFF Forced set reset mode Select a device No status of 8 points in
6. is offered with FX1N Series PLC basic unit FX Soris JY992D88101 Describes instructions in FX1S FX1N FX2N FX2NC Series Programming Manual II 1 Outline of Product 1 1 Features Z i The micro display module FX1N 5DM hereafter referred to as 5DM is A aia mounted on the top face of the FX1S FX1N Series PLC basic unit and MITSUBISH pass can monitor update internal PLC data o D O d fe PLCs installed to FX1S and FX1N Series FX1N 5DM P ey BIA 1 2 Product configuration Main unit FX1N 5DM Accessories Top cover for DM 1 M3 screw to mount top cover 1 1 3 Outside dimensions 17 0 67 When installed to a PLC 2 40 4011 57 11 0 43 oan ie 9 26 MITSUBISHI pl 0 35 1 03 A RA N ULI Note These dimensions N Ss z Ha i measured Cop a from the er side e ga FX1s Series are common ale FS le i to the FX1S and id pg e o FX1N Series Ss 3 23 o Ast fion l FX1N Series 0 wo a Hii ma H g S AIE EZA j Unit mm inches Outer painting color Munsell 0 08GY 7 64 0 81 Mass 20 g 0 05 Ibs 1 4 Name of each part ESC key Cancels the last key operation or returns to the previous screen key Scrolls the device No to
7. screw to fix top cover e Remove the top cover of the basic unit and attach the top cover for DM A instead Plug the 5DM in to the connector B e Ifthe 5DM is always used the top cover can be fixed with the M3 screw C Tightening torque 0 3 to 0 6 N m If the 5DM is used together with a function expansion board remove and attach the 5DM by pressing the 5DM mounting hook provided at the bottom of the 5DM 3 Specifications 3 1 Environmental specifications The environmental specifications are equivalent to those of the PLC main unit Refer to the handy manual offered with the FX1S FX1N Series PLC main unit 3 2 Power supply specifications The power is supplied from the PLC main unit 5V DC 110 mA 4 Outline of Performance This section describes the function list of the 5DM The operator functions available with the operation keys of the 5DM are described on the back of this manual For the 5DM control functions available from the PLC refer to the FX1S FX1N FX2N FX2NC Series Program ming Manual 4 1 Function list Symbols stand for the following X Input Y Output M Auxiliary relay S State 7 Timer C Counter D Data register BFM Butter memory of special units and special blocks Operator functions The operator can use these functions by using only the operation keys of the 5DM Refer to the simplified chart of operations shown on the back face of this manual Func
8. Changes for the Better aa MITSUBISHI PROGRAMMABLE CONTROLLERS MELSEC F DISPLAY MODULE FX1n 5DM USER S MANUAL JY992D84901E This manual only describes the specifications for Display Module FX1N 5DM For complete operation wiring mounting and programming instructions please refer to the FX1S FX1N HARDWARE MANUAL and PROGRAMMING MANUAL These manuals should be read and understood before attempting to install or use the unit Related Manuals Manual name Manual No Description Describes contents related to hardware of FX1S Series JY992D83901 PLC such as specifications wiring and installation It is offered with FX1S Series PLC basic unit Describes contents related to hardware of FX1N Series JY992D88201 PLC such as specifications wiring and installation It is offered with FX1N Series PLC basic unit FX1S Series Hardware Manual FX1N Series Hardware Manual FX Series JY992D88101 Describes instructions in FX1S FX1N FX2N FX2NC Series Programming Manual II 1 Outline of Product 1 1 Features Z Al The micro display module FX1N 5DM hereafter referred to as 5DM is mE dia mounted on the top face of the FX1S FX1N Series PLC basic unit and MITSUBISH pass can monitor update internal PLC data o BOO fe PLCs installed to FX1S and FX1N Series FX1N 5DM A ey AIA 1 2 Product confi
9. N OFF status of four operation keys 1 Input numeric values correspond to the devices as follows 1 Input X 2 Output Y 3 Auxiliary relay M 4 State S 6 Counter C 16 bit current value set value and 32 bit set value 7 Data register D 16 bit8 Data register D 32 bit 9 Time display 10 Counter C 16 bit current value set value and 32 bit current value 5 Timer T 2 0 Enables all operations 1 Enables only the time display function 2 Enables only the monitor function 3 PC hardware errors parameter errors grammatical errors and circuit errors are unconditionally displayed While this bit is ON I O configuration errors parallel link errors and operation errors are also displayed 4 Every operation key is the momentary type and functions as follows While a key is pressed and held ON While key is not pressed OFF 4 3 Description on display area The display area of the 5DM shows the following RUN Displayed while the PLC is running and not displayed while 000 y y4 the PLC is stopped RUNBFM ONRD BFM Displays the contents of the buffer memory when a special block is connected only in the FX1N Series ON OFF Displayed while T or C is ON in the word device monitor function and not displayed while T or C is OFF gt xus B8588 o 6059 BEEBE lt e R reset Displayed while T or C is reset D 32 bit Displayed when a 32 bi
10. a smaller one or decrements a numeric value by key Scrolls the device No to a larger one or increments a numeric value OK key Determines the display device executes write of a numeric value or changes over forced setting and forced resetting Display area Displays the current time and the monitored device status Connector for PLC 5DM mounting hook 2 Installation Install the 5DM to the PLC using the following procedure A Top cover for DM offered as an accessory of 5DM B Connector for optional equipment C M3 screw to fix top cover e Remove the top cover of the basic unit and attach the top cover for DM A instead Plug the 5DM in to the connector B e Ifthe 5DM is always used the top cover can be fixed with the M3 screw C Tightening torque 0 3 to 0 6 N m If the 5DM is used together with a function expansion board remove and attach the 5DM by pressing the 5DM mounting hook provided at the bottom of the 5DM 3 Specifications 3 1 Environmental specifications The environmental specifications are equivalent to those of the PLC main unit Refer to the handy manual offered with the FX1S FX1N Series PLC main unit 3 2 Power supply specifications The power is supplied from the PLC main unit 5V DC 110 mA 4 Outline of Performance This section describes the function list of the 5DM The operator functions available with the operation keys of the 5DM
11. are described on the back of this manual For the 5DM control functions available from the PLC refer to the FX1S FX1N FX2N FX2NC Series Program ming Manual 4 1 Function list Symbols stand for the following X Input Y Output M Auxiliary relay S State T Timer BFM Butter memory of special units and special blocks C Counter D Data register Operator functions The operator can use these functions by using only the operation keys of the 5DM Refer to the simplified chart of operations shown on the back face of this manual Cautions 1 If a keyword to prohibit read write or read and write of programs is registered in the PLC only the clock time display function is available Any other function shown above is not available If any operation is performed in the 5DM when a keyword is registered in the PLC the error display flickers for 5 seconds 2 The automatic backlight OFF function is set to 10 minutes as the initial value As far as the OFF time is not changed by a sequence program the backlight turns off 10 minutes later If any key is pressed after the backlight turns off the contents displayed just before the backlight turns off appear again A key pressed for the first time after the backlight turns off is regarded as a trigger to turn on the backlight and is not regarded as a key operation 4 2 Control devices for 5DM When using the 5DM control function specify data registers D and auxiliary relays M used to contro
12. e No to be displayed monitor function eS Dose Backlight OFF time min ee DO 3 Protects display screen 2 For protect function DO 4 Not available MO Requests edition of displayed device data For specified device MO 1 Edition completion response monitor function MO 2 Disables backlight OFF function For automatic backlight Turns on backlight forcedly OFF function MO 3 Displays or hides operation errors etc 3 Others MO 4 ESC key status 4 MO 5 key status 4 For specified device D8159 MO 6 key status 4 monitor function KO MO 7 OK key status 4 MO 8 Not available MO 9 Not available MO 10 Not available MO 11 Not available MO 12 Not available MO 13 Not available MO 14 Not available 5DM control functions The 5DM is controlled by sequence programs For use of these functions refer to the FX Series Programming Manual II Function Description Enables full use of all operator functions enables only monitor function or enables only clock time display function Allows to specify device type and device No to be displayed in 5DM Protect function Specified device monitor function Error display enable disable function Automatic backlight OFF function Operation key status recognition function Enables or disables error display function operator function Allows to set automatic backlight OFF time initial value 10 min Recognizes O
13. ect the current value change mode Press the key to increase the value Press the key to decrease the value Press the OK key to determine the input At this time the input data is written to the PLC lt Changing the current value of 32 bit D gt Guidelines for the safety of the user and protection of the Micro Display Module FX1N 5DM e This manual has been written to be used by trained and competent personnel This is defined by the European directives for machinery low voltage and EMC e If in doubt at any stage during the installation of the Micro Display Module FX1N 5DM always consult a professional electrical engineer who is qualified and trained to the local and national standards If in doubt about the operation or use of the Micro Display Module FX1N 5DM please consult the nearest Mitsubishi Electric distributor e Under no circumstances will Mitsubishi Electric be liable or responsible for any consequential damage that may arise as a result of the installation or use of this equipment e All examples and diagrams shown in this manual are intended only as an aid to understanding the text not to guarantee operation Mitsubishi Electric will accept no responsibility for actual use of the product based on these illustrative examples e Owing to the very great variety in possible application of this equipment you must satisfy yoursel
14. errors and circuit errors are unconditionally displayed While this bit is ON I O configuration errors parallel link errors and operation errors are also displayed 4 Every operation key is the momentary type and functions as follows While a key is pressed and held ON While key is not pressed OFF 4 3 Description on display area The display area of the 5DM shows the following OROKO RUN Displayed while the PLC is running and not displayed while y VvA the PLC is stopped RUNBFM ON R D TCD BFM Displays the contents of the buffer memory when a special a XYMS ogogo block is connected only in the FX1N Series os ace HOHHH Lo ON OFF Displayed while T or C is ON in the word device monitor function and not displayed while T or C is OFF R reset Displayed while T or C is reset D 32 bit Displayed when a 32 bit D is specified Device type Displays the device type T C D X Y M or S currently being displayed Device No Displays the device No currently being displayed Current value Displays the current value of T C or D Set value Displays the set value of T or C In the case of 32 bit C or D upper 5 digits are displayed in and the lower 5 digits are displayed in 5 Operation List The process for the operator functions are shown below The operation keys are expressed as follows ESC ESC key _ _
15. f as to its suitability for your specific application lt Keyword Entry code error lt Error display gt display gt When an keyword entry code has been input to the PLC only the Z OE d S time can be displayed E ccor rror code E coor If you press the OK key while the time is displayed the error message Error step No re P he ESC k shown on the left flickers for 5 seconds HET BOZ ress the ESC key or ACCE Release the keyword entry code in a peripheral unit such as release the error status to e f al h displ the FX 10P 20P and the personal computer software for creating GIGIS mie error Cisplay sequence programs Manual number JY992D84901 Manual revision E Date June 2008 This manual confers no industrial property rights or any rights of any other kind nor does it confer any patent sfa MITSUBISHI ELECTRIC CORPORATION licenses Mitsubishi Electric Corporation HEAD OFFICE TOKYO BUILDING 2 7 3 MARUNOUCHI CHIYODA KU TOKYO 100 8310 JAPAN cannot be held responsible for any HIMEJI WORKS 840 CHIYODA CHO HIMEJI JAPAN problems involving industrial property rights which may occur as a result of JY992D84901E Effective June 2008 using the contents noted in this manual Specifications are subject to change without notice
16. function Automatic backlight OFF function Allows to set automatic backlight OFF time initial value 10 min Operation key status recognition function Enables or disables error display function operator function Recognizes ON OFF status of four operation keys Cautions 1 If a keyword to prohibit read write or read and write of programs is registered in the PLC only the clock time display function is available Any other function shown above is not available If any operation is performed in the 5DM when a keyword is registered in the PLC the error display flickers for 5 seconds 2 The automatic backlight OFF function is set to 10 minutes as the initial value As far as the OFF time is not changed by a sequence program the backlight turns off 10 minutes later If any key is pressed after the backlight turns off the contents displayed just before the backlight turns off appear again A key pressed for the first time after the backlight turns off is regarded as a trigger to turn on the backlight and is not regarded as a key operation 4 2 Control devices for 5DM When using the 5DM control function specify data registers D and auxiliary relays M used to control the 5DM to special data registers D8158 and D8159 Five data registers and 15 auxiliary relays are occupied for control of the 5DM For the control device use procedure refer to the FX1S FX1N FX2N FX2NC Series Programming Manual
17. guration Main unit FX1N 5DM Accessories Top cover for DM 1 M3 screw to mount top cover 1 1 3 Outside dimensions 17 0 67 When installed to a PLC 2 40 k 40 1 57 3 11 0 43 oon 1 57 9 26 0 35 1 03 L Be hes AB Note These dimensions a Qjo o FT Z 7 i NS Ae H measured oO A arr from the side e ga FX1s Series are common ale FS le to the FX1s and TEN 8 FX1N Series ea ca f o Ast SS um FX1N Series SD UE 108 8 8 E 018 oE hena A i 8 SSS id LACIRS 2222 j Unit mm inches Outer painting color Munsell 0 08GY 7 64 0 81 Mass 20 g 0 05 Ibs 1 4 Name of each part ESC key Cancels the last key operation or returns to the previous screen key Scrolls the device No to a smaller one or decrements a numeric value by key Scrolls the device No to a larger one or increments a numeric value OK key Determines the display device executes write of a numeric value or changes over forced setting and forced resetting Display area Displays the current time and the monitored device status Connector for PLC 5DM mounting hook 2 Installation Install the 5DM to the PLC using the following procedure A Top cover for DM offered as an accessory of 5DM B Connector for optional equipment C M3
18. l the 5DM to special data registers D8158 and D8159 Five data registers and 15 auxiliary relays are occupied for control of the 5DM For the control device use procedure refer to the FX1S FX1N FX2N FX2NC Series Programming Manual Function Description Clock function Display Displays current time of clock function built in FX1S FX1N Series Setting Allows to set time year month day hour and minute Device monitor function Bit device monitor Word device 16 bit monitor Word device 32 bit monitor Displays ON OFF status of X Y M and S Displays current and set values of T and C and current value of D Displays current and set values of 32 bit C and current value of D Displays buffer memory of special units and special blocks offered only in FX1N Series Displays error code and error occurrence step No when a PLC error has occurred Forces ON and OFF bit devices Y M and S Clears current value of T and C current value 0 contact OFF Buffer memory monitor function Error display function Forced set reset function T C reset function Data change function Current value change Set value change Change current value of T C and D Change set value of T and C Special D Control device Description Application DO Device type to be displayed 1 For specified device DO 1 Devic
19. ld the OK key for 2 seconds or more the display changes over alternately between 16 bit BFM and 32 bit BFM Increase or decrease the BFM current value using the or key Y 1 Write the data you have input to the BFM oF CAUTION Vv Hy Depending on the type of the connected special block the BFM is cleared when the power is turned off or the mode is changed T Timer over between RUN and STOP When using a special unit write the data finally to the BFM using a sequence program using FNC 79 TO instruction write to BFM Guidelines for the safety of the user and protection of the Micro Display Module FX1N 5DM This manual has been written to be used by trained and competent personnel This is defined by the European directives for machinery low voltage and EMC If in doubt at any stage during the installation of the Micro Display Module FX1N 5DM always consult a professional electrical engineer who is qualified and trained to the local and national standards If in doubt about the operation or use of the Micro Display Module FX1N 5DM please consult the nearest Mitsubishi Electric distributor Under no circumstances will Mitsubishi Electric be liable or responsible for any consequential damage that may arise as a result of the installation or use of this equipment All examples and diagrams shown in this manual are intended only as an aid to understanding the text not to guarantee operation Mitsubi
20. nitial status D flickers T C D 16 bit D 32 bit X Y M S or BFM BFM is displayed only when the FX1n Series PLC is used lt Monitoring 16 bit T or 16 bit C gt lt Changing the current value set value of 16 bit T or 16 bit C gt RUN gt D gt gt A OK OK bu Changing the Determine current value the input o TEE gt Ls S OK OK OK gt L lt Resetting the current value gt Changing he OK OK set value Press and hold it f ON is displayed when T or C is ON and R is displayed while resetting aiaa or more Change over the device to monitor T or C that is not used in the program is not displayed A horizontal line is displayed if there is none of T or C in the program When the OK key is pressed once the current value is changed and when the OK key is pressed three times the set value is changed Flickers while changing Press the key to increase the value Press the key to decrease the value Press the OK key to determine the input At this time the input data is written to the PLC When the OK key is pressed and held for 2 seconds or more while the current value is changed the current value is reset to 0 and the contact turns off When the OK key is pressed once again the current value reset operation will be com
21. ory change gt gt m m gt OK gt g OK F OK u g gt gt OK Press and hold lt f lt gt gt Y A Write the data you have input to the BFM at CAUTION v ft 79 TO instruction write to BFM for 2 sec or more If a special block is connected to the FX1N Series when you select a device a buffer memory hereafter referred to as BFM is BEM displayed A displayed numeric value indicates the unit No When you press the OK key BFM monitor starts for the unit having the displayed unit No The BFM No is displayed The BFM current value is displayed Select the BFM No After pressing the OK key you can change the value of the displayed BFM No Every time you press and hold the OK key for 2 seconds or more the display changes over alternately between 16 bit BFM and 32 bit BFM Increase or decrease the BFM current value using the or key Depending on the type of the connected special block the BFM is cleared when the power is turned off or the mode is changed T Timer over between RUN and STOP When using a special unit write the data finally to the BFM using a sequence program using FNC lt Monitoring 32 bit D gt RUN D gt 4 D p OK OK 0 n mono Lat Le uu D is scrolled by 2 points at a time by the key and by 1 point at a time by the key Sel
22. pleted lt Monitoring a bit device X Y M S gt lt Forced setting resetting a bit device Y M S gt RUN RUN 1 gt OK OK OK Ep o__o 6 o__o n O Y Y Set or reset the bit eh device O00 o s gt b i o5 ee From the displayed device No the ON OFF Forced set reset mode Select a device No status of 8 points in the case of X or Y or 10 A selected device is indicated with underline points in the case of M or S is indicated The current ON OFF status is reversed OFF status CO ON status o Qo Underline flickers The device turns on and off alternately when the OK key is Eight points in the case of X or Y or 10 points in the case of M or S are scrolled at a time key Scrolls toward larger device Nos key Scrolls toward smaller device Nos pressed If the OK key is pressed while the device is ON it turns off If the OK key is pressed while the device is OFF it turns on lt Monitoring 32 bit C gt Current value lt Changing the current set value of 32 bit C gt RUN D 1 gt Ic OK OK i ODetermins the input 755 IGG Ls lt Resetting the current value gt OK OK z Press and hold it for S 2 seconds or more
23. reset operation will be completed Press and hold it for 2 seconds or more lt Monitoring 32 bit C gt Current value lt Changing the current set value of 32 bit C gt RUN D De OK ok i Determine Pen the input eso iD ug lt Resetting the current value gt o i gt ox Press and hold it for RUN c S l sar OANA cra UUUL Set value 2 seconds or more D n Press the or key to change over the current value and the set value For the set value S is added ina u right position above the device No m When the OK key is pressed the current value or the set value is changed Uu Press the key to increase the value Press the key to decrease the value Press the OK key to determine the input At this time the input data is written to the PLC When the OK key is pressed and held for 2 seconds or more while the current value is changed the current value is reset to 0 and the contact turns off When the OK key is pressed once again the current value reset operation will be completed lt Monitoring 16 bit D gt lt Changing the current value of 16 bit D gt p mnan u UU a D is scrolled by 1 point at a time Select the current value change mode OK OK Ls
24. shi Electric will accept no responsibility for actual use of the product based on these illustrative examples Owing to the very great variety in possible application of this equipment you must satisfy yourself as to its suitability for your specific application lt Monitoring 16 bit T or 16 bit C gt lt Changing the current value set value of 16 bit T or 16 bit C gt RUN gt DI r A OK OK 4 W Changing the i Determine current value the input HH Iga gt Ls a OK OK OK gt lt Resetting the current value gt 2 ga b OK ON is displayed when T or C is ON and R is displayed while resetting Change over the device to monitor T or C that is not used in the program is not displayed A horizontal line is displayed if there is none of T or C in the program When the OK key is pressed once the current value is changed and when the OK key is pressed three times the set value is changed Flickers while changing Press the key to increase the value Press the key to decrease the value Press the OK key to determine the input At this time the input data is written to the PLC When the OK key is pressed and held for 2 seconds or more while the current value is changed the current value is reset to 0 and the contact turns off When the OK key is pressed once again the current value
25. t D is specified Device type Displays the device type T C D X Y M or S currently being displayed Device No Displays the device No currently being displayed Current value Displays the current value of T C or D Set value Displays the set value of T or C In the case of 32 bit C or D upper 5 digits are displayed in and the lower 5 digits are displayed in 5 Operation List The process for the operator functions are shown below e The operation keys are expressed as follows ESC ESC key _ _ key key OK OK key Time display screen when the power is turned on lt Selecting a device gt RUN lt Setting the time gt I2 i UG OK m OK An item being changed flickers a Ic Set year month day hour and minute in this order cog Q 1 b Press and hold 1 Determine When the OK key is pressed at minute set up the setting operation will be completed it for 2 seconds sfz the input or more OK TCD XYMS Program error Keyword error vV 5 Error display lt key key gt Refer to error display Ok To 41 gt Determine the input Entry code error Select an either device using the and keys In the i
26. the case of X or Y or 10 A selected device is indicated with underline pans rime case of M o Ola o__a The current ON OFF status is reversed Se Underline flickers The device turns on and off alternately when the OK key is pressed fei one ore ie Erola ore ponis Bee aie if the OK key is pressed while the device is ON it turns off 4 key Scrolls toward larger device Nos If the OK key is pressed while the device is OFF it turns on key Scrolls toward smaller device Nos lt BFM unit selection gt S State v sal lize Y 1 lt Buffer memory No selection gt lt Buffer memory change gt BFM BFM gt D gt n gt OK gt 7 OK OK o OK Press and hold v i for 2 sec or more OG a special block is connected to the 1 eries when you select a device a buffer memory hereafter referred to as Is Vv a O If ial block i d to the FX1N Seri hi l devi buffi h ft ferred BFM i BEM displayed A displayed numeric value indicates the unit No When you press the OK key BFM monitor starts for the unit having the displayed unit No The BFM No is displayed The BFM current value is displayed Select the BFM No After pressing the OK key you can change the value of the displayed BFM No Every time you press and ho
27. tion Description Clock function Display Displays current time of clock function built in FX1S FX1N Series Setting Allows to set time year month day hour and minute Device monitor function Bit device monitor Displays ON OFF status of X Y M and S Word device 16 bit monitor Displays current and set values of T and C and current value of D Word device 32 bit monitor Displays current and set values of 32 bit C and current value of D Displays buffer memory of special units and special blocks offered only in FX1N Series Displays error code and error occurrence step No when a PLC error has occurred Buffer memory monitor function Error display function Forced set reset function Forces ON and OFF bit devices Y M and S T C reset function Clears current value of T and C current value 0 contact OFF Data change function Current value change Change current value of T C and D Set value change Change set value of T and C 5DM control functions The 5DM is controlled by sequence programs For use of these functions refer to the FX Series Programming Manual II Function Description Enables full use of all operator functions enables only monitor function or enables only clock time display function Allows to specify device type and device No to be displayed in 5DM Protect function Specified device monitor function Error display enable disable
Download Pdf Manuals
Related Search