Home

OWNER`S MANUAL Seat system for Power Wheelchair

1. VS Seat system for Power Wheelchair User Manual VS Table of Contents Table of Contents Important information about user manual 6 Technical support eects eeeee eee eeeeeee eee eeeeaaeeeeeeeeaeeeeeeeaaeeeeeeeaaes 7 Spare parts ANd ACCESSOLICS cceeeeeeeeeeeeeeeeeeeeeeeeeeseaeeeeeeeeee 7 Baen M TEE A A L E E A E T 7 Guarantee and Service eeeeseesssesrrssrtrsstrssrtrsernsrnnennnnnnnnt 7 Product approval senretene aeiiaaie ania RiR EE NR 7 Safety rules and regulations 0 ccccccece ee eeeeeeeeeeeeeeeeeteee 8 17 General introduction 0 cc ccceceeceeeeeeeeeeeeeeeaeeeceeeeseaaeeeeeeeeseaaeeteeeeeees 18 Dosign Sc FUMCUON ssc se dicuuh cece aa S 19 Operation ii kteniieeinsin st kde E A A aE 24 Settings and AdjUStMeNt cece cece ee eeeee cette ee eteeeeeeeeeetaeeneeeeees 29 Aim TO SU sien ccocendtie sa divapwtecdaewedinsadtasd stage a a i Anaa 29 Chest SUPPOM eee cece cece ee eeeeeeeeeeeeeeaaeeeeeeeeseaeeeeeeeeeseieeestaeeteaes 29 Head feStiscscccitieectecetiseetivmssscesnetearcconerseagcassesevnbasocemenbaasceneeesaderes 30 Trunk SUpport ooo cece eee etcne eect teat eee ee eaaae eee eesaaeeeeeetaaeeeeeneaaeeeeeteaa 31 LUMD Ar SUP POM oscri diini irna R aE 31 aae Plate T TEE T E E E 32 Knee SUPPOME ecsiucsriacie inn EE E EEE 34 Angle GAUGE eeecceceeceeeceeee cence centr eeeeeeeeeenaeeeeeeenseeeeeeeeseneeeeensennees 34 Positioning Deltares Ea aai 35 Control pa
2. Technical specifications Dimensions amp weight information Seat height with electric seat lift Seat width Seat depth Back rest height Arm rest height Distance between arm rests Distance between seat cushion and foot plate Back rest angle Leg rest angle Max user weight 18 20 without seat extension With seating limitations Junior 21 31 17 19 16 20 22 24 6 11 14 16 18 11 19 90 180 90 180 170 Ibs 41 Technical specifications Adult 21 31 17 19 18 24 22 24 6 11 14 16 18 19 22 90 180 90 180 220 265 Ibs US VS Order no 205216 US 0
3. Make sure that nothing can get in between the chassis and the seat when the seat lift is being used Using the seat lift alters the center of gravity which always means an increased tipping risk Always travel at low speeds and only use this seat function on a level surface and not on slopes ramps hills or other gradients Center of gravity Note that the following factors may affect the center of gravity of the seat wheelchair and thus the tipping risk e Raising the seat lift Height and angle of seat e Position or weight distribution of the body Travel on sloping surfaces e g ramp or hill e When wearing a rucksack or other items depending on the extra weight Elevation to standing position Elevation to standing position and operation in standing position must only be done on a flat surface When the chair is in elevated position never reach out from the chair due the higher tipping risk If your wheelchair starts to move in an unexpected way immediately let go of the joystick to stop the wheelchair Except in an emergency never use the off on button to stop the wheelchair This could lead to the wheelchair stopping quickly and violently and could lead to personal injury User Manual VS Safety rules Safety rules Positioning Belts Always wear your positioning belt while in your wheelchair If signs of damage or wear appear replace the positioning belt immediately through your Permobil dealer Tran
4. using a seat belt attached to the vehicle The only other safe alternative is that users be transferred into factory vehicle seating for transportation and use safety restraints made available by the auto industry The only wheelchair transportation system Permobil recommends is a Permolock C used in combi nation with an approved Permobil wheelchair Unless using a Permolock C with an approved Permobil wheelchair never sit in your wheelchair while in a moving vehicle In an accident or sudden stop you may be thrown from the chair and seriously injured or killed Permobil positioning belts are designed to position the user only and not to protect you in the event of a motor vehicle accident The positioning belts do not replace use of a vehicle mounted restraint User Manual VS Safety rules Safety rules Maintenance and service Carry out only the service and maintenance activities noted in this user manu al All other servicing alterations and changes to the seat and its accessories must be carried out by a competent servicing engineer or person with sufficient knowledge to give a competent result In case of doubt always contact a com petent servicing engineer or Permobil The power supply must always be interrupted for all work or servicing on the seat s electrical system Read more on how you can do this in your wheelchair user instructions chassis manual Use only spare parts or accessories approved or recommended
5. 2 Move the continuous position screw 2 on the leg rest to a suitable position see photo 3 Ensure that the knee support is fully pushed in against the position screw then tighten the knee support locking knob 1 Angle gauge When starting to use the VS seat it may be difficult to rise up completely and require a deal of training to rise up to full height in the seat The supplied angle gauge can be mounted on the seat frame to give an indication of the user s progress The angle gauge is self adhesive on the rear and is mounted on the side of the seat frame see photo Its position can be varied depending on what accessor ies are mounted on the seat fit it wher ever there is space Fit the angle gauge to show 0 in sitting position 34 Settings and adjustment a Adjusting the position of the knee support Mounting the angle gauge User Manual VS Settings and adjustment Positioning Belt Option Fitting the Positioning Belt There is an accessory rail on both sides of the seat frame for mounting such items as the positioning belt Mount the positioning belt in the upper track of the rail 1 Screw the belt in place with the snap lock on the side which best suits the user and the other part with the buckle on the opposite side 2 After mounting check that the belt buckle locks properly in the snap lock Fitted Belt Snap Lock for the Belt A WARNIN
6. back rest move forwards Certain seats may have a more limited back rest angle due to high user weight Movement of seat during adjustment of back rest angle 26 User Manual VS Operation Leg rest angle This function adjusts the leg rest angle Moving the toggle switch forwards angles the leg rests forward Moving the toggle switch backwads angles the leg rests backwards Leg rest angle Movement of leg rests during adjustment of leg rest angle Seat angle option This function adjusts the seat angle For this function to work the seat must be in sitting or recumbent position Moving the toggle switch backwads angles the seat backwards Moving the toggle switch forward angles the seat for wards again Movement of seat during adjustment of seat angle 27 User Manual VS Operation Memory function The control panel has an integral memory with three memory positions Each memory position can store all the seat s electrical settings Storing memory Before storing a seating position in memory position the seating system in the position that is desired to be stored Enter the memory mode by pressing and holding the memory button 8 for two seconds see illustration below While in the memory mode the LED flashes green Activate the memory storage function by holding down button 4 for two seconds The symbol above will light up green which means that the fun ction has been activated Press an
7. back rest see photo 2 Adjust head rest height depth as required 3 Tighten the knob 1 Adjustment of angle 1 Release the knob 2 on the rear of the head rest see photo 2 Adjust head rest angle as required 3 Tighten the knob 2 30 Settings and adjustment L Head rest with wide adjustment capability Head rest adjustment User Manual VS Settings and adjustment Trunk support accessory Height adjustment 1 Release the knob on the rear of the back rest see photo Adjust the trunk support to the desired height Retighten the knob Lumbar support Heighit depth adjustment 1 2 Remove the back Adjust the lumbar support as requi red Replace the back cushion Adju Settings and adjustment sting the trunk support User Manual VS Settings and adjustment Foot plate Angle adjustment The foot plate angle can be adjusted by screwing the nuts 2 on the foot plate adjustment screws in or out see photo on right Foot plate Height adjustment 1 Releast the two locking screws 1 on the foot plate see photo 2 Adjust the foot plate to the desired height 3 Retighten the screws 4 Where necessary on seats without standing operation function adjust the height of support wheels so the leg rest does not hit the ground during elevation Reversing the foot plate fixing If further adjustment of foot pla
8. by Permobil All other use could lead to changes which might impair the function and safety of the seat It could also lead to the guarantee on your seat becoming invalid Note that the seat is heavy and contains many moving parts which means there will always be some risk of crushing User Manual VS Safety rules Safety rules Storage Never store the seat and its accessories in areas subject to condensation vapor or moisture on surfaces e g utility rooms or similar If you are unsure how best to store the wheelchair contact your supplier or Permobil for information Damage breakdowns to the seat and its accessories If you start noticing that the seat and its various functions are not behaving as expected or if you suspect anything is wrong stop your test drive as soon as possible turn off the wheelchair and contact your aid center or Permobil for information It is most important that Permobil is informed that the chair and its accessories have been damaged during transport during driving or for some other reason as soon as possible after the damage has occurred There could be a risk that the seat and its accessories can no longer be operated safely and without danger User Manual VS General introduction General introduction The VS seat is designed to give wheelchair users extra freedom of movement but it can also be used as a rehabilitation aid The seat is controlled from the control panels for
9. may reduce your wheelchair s performance or safety or may not be appropriate for your needs It is also of the utmost importance that you devote sufficient time to become acquainted with the different buttons the function and steering controls the dif ferent adjustment possibilities of the seat etc of your wheelchair and its acces sories before you begin using it Do not undertake your own first test drive without making sure that you have assistance in the immediate vicinity if you should need help In order to make sure that nothing happened to the wheelchair while it was being shipped to you you should check the following items before beginning to use it e that all products ordered are included in the delivery incuding operating instructions and possible other documentation If you suspect that something is missing then contact your supplier or Permobil for more information as soon as possible e that no transport related or other damages have occurred to the wheelchair seat and its accessories If you discover that something has been damaged or in some other manner appears to be incorrect then contact your supplier or Permobil for more information as soon as possible before you continue the checks User Manual VS Safety rules Safety rules Before taking the seat into use for the first time and after adjustments or other changes to the seat have been made the following safety checks must always be carried out
10. Check that all supports for example the chest roller and knee stop are mounted before starting to use the chair Check that all tapes on the seat are intact and correctly mounted After adjustment and other actions the following safety checks must be carried out 1 Check that the bolts on all actuators and articulated rod heads see photo have been properly tightened 2 Check that the stop chain is fitted to the leg rest see photo The screws holding the chain must be screwed tight 3 Check that the locking screws 1 for height adjustment on the foot plate are tightened see Fig 3 Check that the two locking nuts 2 for angle adjust ment on the rear of the foot plate are tightened see Fig 3 4 Check that the screws 4 pcs for the arm rest stop are properly tightened on both sides of the seat User Manual VS Safety rules Safety rules Articulated rod head Leg rest with foot plate seen from behind User Manual VS Safety rules Safety rules Risk of crushing Note that the seat is heavy and contains many moving parts which means there will always be some risk of crushing Use the seat s electric seat functions with the greatest care Above all when you have moved up to or under a table or other fixed or moveable object always make sure there are no items in the immediate vicinity which could interfere with the seat s moving parts Operation of seat lift
11. G Permobil positioning belts are designed to position the user only and not to protect you in the event of a motor vehicle accident The positioning belts do not replace use of a vehicle mounted restraint 35 User Manual VS Settings and adjustment Control panel rotating panel holder The location of the control panel can be adjusted lengthwise to find the optimum driving position It is also possible to adjust the angle of the panel sideways which facilitates getting in and out Length adjustment 1 Undo the screw on the underside of the armrest and adjust the panel to the required position 2 Tighten the screw Adjustment of friction joint Using the knob on the friction joint it is possible to adjust how easily or stiffly the panel can be angled laterally Length adjustment screw Friction joint knob Knob Control panel with rotating panel holder 36 User Manual VS Control panel parallel panel holder The location of the control panel can be adjust ed lengthwise to find the optimum driving pos ition The panel can also be pushed out to the side diagonally back to facilitate getting in and out Length adjustment 1 Undo the screw on the underside of the armrest and adjust the panel to the required position 2 Tighten the screw Adjustment of friction joint Using the knob on the friction joint it is possible to adjust how easily or stiffly the panel can be pushed out t
12. aches a suitable depth The depth can be adjusted at intervals of 1 3 Screw the fixing in position with the two nuts Chest support Height adjustment 1 Release the Allen screws 1 on the lock ing ring on either side of the chest sup port see photo 2 Adjust the chest support to a suitable height but never so high that the fixing is not visible at the lower edge of the sleeve 2 see photo 3 Tighten the Allen screws on the locking ring Chest support L A WARNING Never adjust the height so far that the fixing is not visible at the lower edge of the sleeve 29 User Manual VS Settings and adjustment Head Rest accessory Adjustment of height 1 Release the knob 1 on the rear of the back rest see photo 2 Adjust head rest height as required 3 Tighten the knob 1 Adjustment forwards backwards 1 Release the knob 2 on the rear of the back rest see photo 2 Adjust the head rest forward backwards as required 3 Tighten the knob 2 Head rest accessory This head rest has extended adjustment capability to give the user the best comfort The head rest is easy to remove remount while preserving the same settings Removal 1 Release the knob 3 on the rear of the back rest see photo 2 Detach the head rest by lifting it straight up Mounting Mount in reverse order Adjustment of height depth 1 Release the knob 1 on the rear of the
13. d hold the desired store button 5 6 or 7 for three seconds to memorize the current seat position in a memory location see illustration below The LED above the memory position will light red and the control panel will emit a tone when the memory has been successfully stored Return to standard seat function operating mode by pressing the memory button 8 see illustration below Recalling memory Enter the memory mode by pressing and holding the memory button 8 for two seconds see illustration While in the memory mode the LED flashes green Press and hold the desired recall button 1 2 or 3 to move the seating system to the desired memory position see illustration Releasing the Recall button stops actuator movement as a safety feature Actuator movement stops the LED above the memory position lights green and the control panel emits a tone when the stored position is reached Return to standard seat function ope rating mode by pressing the memory button 8 see illustration Control panel memory function 28 User Manual VS Settings and adjustment Settings and adjustment Arm rest 1 Unscrew the two nuts on the inside of the arm rest see photo 2 Adjust the arm rest for height and angle 3 Tighten the two nuts Chest support Depth arste Unscrew the two nuts on the inside of the arm rest see photo Arm and chest support 2 Move the fixing on the chest support until it re
14. dampness heavy rain snowfall and similar situations If the seat is exposed to any of these do not use it again before it has completely dried out Remember also that certain surfaces on the seat may heat up or cool down under lengthy exposure to strong sunshine or cold etc If any of the seat enclosures or the control panel case show signs of cracking etc they should be replaced so no moisture can penetrate and damage the electronics User Manual VS Safety rules Safety rules Transport The wheelchair seat must be transported in or with transport solutions that have been approved for this purpose Do not lift or move the wheelchair seat by any of its removable parts Doing so could lead to personal injury and property damage including damage to the seat and wheelchair Check that the wheelchair is properly secured and that the wheel locks are not disengaged The wheelchair can be locked into position by running fastening straps through the brackets at the front and back Also check that the fastening points on the transport vehicle are well anchored A defectively fastened chair can cause serious injury to persons in the vehicle and serious damage to the vehicle Use Prohibited in Motor Vehicles Permobil recommends that users NOT be transported in any kind of vehicle while in their wheelchair unless the user is in an approved Permobil wheel chair configuration has secured the wheelchair using a Permolock C and is
15. e the seat and wheelchair In order to reduce these risks you should read the Owner s Manual carefully in particular the safety instructions and their warning texts Throughout this manual the following symbol will be used to note items that have significant importance to safety concerns Please use caution where this symbol appears ZA WARNING Please use extreme caution where this warning symbol appears Failure to observe warnings can lead to personal injury and property damage including damage to the wheelchair Permobil is not responsible for personal injuries or property damage resulting from any person s failure to follow the warnings and instructions in this manual Permobil is not responsible for injuries or damage resulting from failure to exer cise good judgment The final selection and purchasing decision about the type of electric wheelchair and seating system to be used is the responsibility of the wheelchair user and his or her healthcare professional Permobil Inc is not responsible for inappropriate selections of wheelchair models and seating system or features or improper fitting of the wheelchair and seat User Manual VS Safety rules Safety Instructions General Your wheelchair and seat was configured specifically for your needs as prescribed by your healthcare provider Consult your healthcare provider before changing the seat position or making any other adjustment Some adjustments
16. er Rinse thoroughly and dry with a soft cloth Do not use solvents or abrasive kitchen cleaners A WARNING Never hose the wheelchair down as the electronics may be damaged The wheelchair must always be turned off when being cleaned 38 User Manual VS Care amp Maintenance Transport Care and maintenance Checks At regular intervals check the following that the locking nuts on the swivel heads are tight that the actuators are in place in the actuator fixings that the knee stop tape and the tape to the leg rest foot plate are not worn and that the seams are intact Check the condition of the belts regularly in case any damage or worn pla ces have developed that moving parts such as arm rest or parallel stay are in place and that all knobs are tightened see safety rules pages 10 11 that the green indicator lamp on the button box goes out when the seat is raised above or lowered below the correct height for elevation Always contact Service is defects are discovered on the seat as the use of a defective seat could both injure the user and damage the seat Transport To take up less space when transporting the seat the back rest can be detached and laid on the seat 1 Release the two knobs 1 on the rear of the back rest see photo 2 Open the two quick acting locks 2 3 Lay the back rest on the seat cushi on DERAN the back si 39 User Manual VS
17. he toggle switch is moved back wards and forwards when it is moved forwards Shift Change the control button function by moving the shift function toggle switch forwards Change back by moving the shift function toggle switch forwards again The symbols for the active functions will light up Memory function The control panel has an integral memory with three memory positions Each memory position can store all the seat s electrical settings eae 23 User Manual VS Operation Operation General The seat functions are controlled from the seat s control panel The control panel s appearance varies according to the functions with which the chair is equipped See two examples below A standard panel and a panel for a seat equipped with shift and memory functions The shift toggle is used when a toggle switch has two function capability The active function is changed by pressing the shift toggle first The memory fun ction can save up to three favourite seating positions which can easily be retrie ved regardless of the seats current position The main switch on the wheelchair must be turned on before the seat s control panel will work For information on the wheelchair control panel see the Chassis User Manual Exemple on Control panel with shift and memoryfunction 24 User Manual VS Operation Shift Change the control button function by moving the shift function toggle switch forwards Change back by m
18. hotographs illustrations and specifications are based on the product information that was available at the time this user manual was printed Photographs and illustrations that appear in the user manual are typical examples and not intended to be exact depictions of different parts of the seat We reserve the right to make changes to the product without prior notification User Manual VS Technical support guarantee etc TECHNICAL SUPPORT In the event of technical problems you should contact your dealer Always state the chassis serial number when contacting Permobil to ensure that the correct information is provided SPARE PARTS amp ACCESSORIES Spare parts and accessories must be ordered through your dealer SCRAPPING THE WHEELCHAIR Contact Permobil Inc for information about scrapping agreements in force WARRANTY A warranty registration card is attached to each new wheelchair The Permobil Inc Product Warranty Information sets forth the conditions of the warranty Contact your dealer or Permobil Inc USA for information about the warranty period for this wheelchair User Manual VS Safety rules Safety Instructions General The seat is heavy and contains many moving parts Special care must therefore be taken when it is used Please read and follow all instructions and warnings in this manual before operating your seat together with your Permobil powered wheelchair Incorrect use may both injure the user and damag
19. nel cceeeeeeececeeeeeeeeeeeeeeeeeeeeseeeeeesaeeseeeeeesseeeseeeeseaes 36 Care and maintenance cccccceeesceeeeeeeeeeeeeeceeeeeeeaeeeeneeeeeaaeeeseeeeee 38 AN tcl gt ole E E E E A rr E T T E E 39 Technical Specifications uiseeiiin anneuenn aa e 41 User Manual VS Important information about user manual Important information about user manual Congratulations on your choice of Permobil product We will do all in our power to ensure your continued satisfaction with our product Before you start using your seat and wheelchair it is important to read and understand the contents of this user manual and especially the section on Safety The user manual is primarily designed to inform you about the functions and capabilities of your seat and to advise you on the best way of using it It also contains important safety and maintenance information and describes some of the problems which might arise in use Always keep the user manual on or near your wheelchair as you may need to consult its important information on use safety and maintenance You can also find information on our products on our website You will find us on www permobil se If your seat bears a sticker with the words Customized product it has been adapted to your needs and requests This means that design and functions may differ from the text of this user manual or from the design and functions of other seats of the same type All information and all p
20. o the side Settings and adjustment The panel can be pushed out to the side diagonally back to facilitate getting in and out Knob Control pane with parallel panel holder 37 User Manual VS Care amp Maintenance Care and maintenance Regular care and maintenance will prevent unnecessary wear and damage to your seat The following is general advice recommended by Permobil For severe soiling of the upholstery or damage to surface finish contact Permobil for information Upholstery cloth vinyl For normal cleaning wash the upholstery with lukewarm water and a mild non abrasive soap Use a soft cloth or brush Before the surface dries wipe off any water soap residues with a clean dry cloth This procedure may be repeated to remove stubborn dirt or stains If necessary the cover may be removed before cleaning See also the washing instructions on the upholstery materials Metal surfaces For normal cleaning proceed carefully with a soft cloth sponge hot water and a mild detergent Wipe down carefully with a cloth and water and dry off Remove skuff marks from semi matte surfaces with soft wax follow manufacturer s instructions Remove skuff marks and scratches from shiny surfaces using car polish either liquid or in paste form After polishing apply soft car wax to restore the original surface gloss Plastics For normal cleaning wash plastic surfaces with a soft cloth mild detergent and hot wat
21. oving the shift function toggle switch forwards again The symbols for the active functions will light up Standing The seat rises to standing position when the toggle switch is moved forward and lowers to sitting when the switch is moved back The standing function can be configured to suit each user by pre programming one of the three possible standing sequences The picture sequence below shows the standing sequence which starts by straightening the user s hips and legs before raising them to a standing posi tion This sequence minimises pressure on the user s knees The standard control panel does not feature a toggle switch for the standing function On such models standing is activated by the Leverman function in the joystick panel Please see the section on Leverman in the relevant chassis owner s manual Operation Shift function Standing function Movement of seat to from standing position with a standing sequence that minimises pressure on the user s knees 25 User Manual VS Operation Seat lift This function adjusts the seat height Moving the toggle switch forward raises the seat Moving the toggle switch backwards lowers the seat again Seat lift Movement of seat during adjustment of seat height Back rest angle This function adjusts the back rest angle Moving the toggle switch backwards makes the back rest slope backwards and moving the toggle switch forwards makes the
22. rol system Each control switch can have two functions and the symbol for the active fun ction will light up Functions are changed using the shift function see adjoining page The number of available functions will vary depending on how your wheelchair and seat are equipped Seat control panel 20 User Manual VS Design and function Design and function The symbols on the control panel indicate what seat functions are available what seat functions are restricted and what seat functions will cause speed reduction or stop motion completely The symbols may be unlit show a conti nuous light or flash Unlit symbol The symbol for the function is unlit This means that the function is not currently available Use the shift button to switch between left and right seat function on the control switch Illuminated symbol A constantly illuminated symbol gives information relating to operating speed A constant green light means that the wheelchair can be operated at maximum speed A constant yellow light means that the maximum speed for the wheelchair is restricted due to the current position of the seat function A constant red light means that the wheelchair cannot be used for travel due to the current position of the seat function Flashing symbol A flashing symbol gives information relating to the actuators A flashing green symbol means a special function e g the memory function A flashing yello
23. sfer into and out of the chair Be sure that the power is turned OFF before entering or leaving the wheel chair and before lifting the control side armrest When transferring into or out of the wheelchair every precaution should be taken to reduce the distance between the wheelchair and the place to which the user is transferring Overextending this distance can cause user to overexert lose balance or fall Permobil recommends that users transfer in the presence of or with the assis tance of an attendant Use caution when bending or reaching Never use the joystick as a handhold or point of support Do not use foot plates or armrests as supports when transferring into or out of the wheelchair The footplates and armrests are not designed to be weight bearing structures Excessive force may cause them to give way resulting in personal injury or property damage including damage to the wheelchair User Manual VS Safety rules Safety rules Passengers The seat is not designed for transporting passengers whatever their age Nor is it designed for taking heavy items other than the user s personal belongings The indicated maximum user weight given in this manual must not be exceeded Ignoring this could impair the wheelchair s maneuverability and stability Use in different climates Permobil s seats are designed to tolerate most weather conditions but you should avoid exposing the seat to severe cold persistent
24. te height is necessary it is possible to reverse the fixing which will enable the foot plate to be set higher up 1 Unscrew the support wheels on seats with standing operation they are mounted with two screws on either side of the leg rest while on seats without standing operation they are mounted on the rear edge of the foot plate see photo 32 Settings and adjustment Support wheel fixing on seat without standing operation function Support wheel fixing on seat with standing operation function User Manual VS Settings and adjustment 2 Remove the knee support mounted with one screw see Fig 11 3 Unscrew the six screws that hold the foot plate in place see photo 4 Release the two locking screws on the footplate see photo at the top of the previous page 5 Turn the fixing over and remount in reverse order 33 Settings and adjustment The foot plate is mounted with six screws Leg rest seen from behind User Manual VS Knee support Adjustment of position 1 Adjust the knee support in sitting position to a location approx 3 4 cm in front of the legs Carry out adjust ment with the knob on the rear edge of the seat frame see photo Rotate the knob clockwise to reduce the distance between the leg and the knee support and anticlockwise to increase the distance Knee support Adjustment of height 1 Release the knee supports locking knob 1 see photo
25. the wheelchair and seat If the seat has the standing operation function the chair may be operated at reduced speed with the seat in the standing position ZA WARNING Elevation to standing position must only be done on flat surfaces When the chair is in elevated position never reach out from the chair due the higher tipping risk ZA WARNING Travel in standing position must only be done on flat surfaces User Manual VS Design and function Design and function General The seat consists of a seat frame with seat and back rest arm rest and leg rest To facilitate use of the elevation function it is also fitted with knee calf and chest supports The photo shows the seat detached from the chassis VS 1 Head Rest accessory 5 Knee support 2 Control panel 6 Foot plate 7 Back cushion Tr nk support 8 Chest support 4 Seat cushion amp Amres 19 User Manual VS Design and function Design and function Control panel The seat s electrical functions are controlled from the control panel The control system may be in the form of conventional push buttons or may have toggle switches for those users who find these easier to maneuver The toggle switch is moved forward to operate the front button and back to operate the rear button The functions of the control panel are here described when fitted with conven tional push buttons but the functions are the same whatever the design of the cont
26. w symbol means that the function is barred in one direction due to a safety switch The control switch for the current function will only work in the safe direction A flashing red symbol means that a fault in the current actuator has been detec ted This may mean that the seat function will not work Contact service 21 User Manual VS Design and function Design and function Standing ra Fa The seat rises to standing position when the toggle switch is moved forward and lowers to sitting when the switch is moved back The standing function can be configured to suit each user by pre programming one of the three possible standing sequences The symbol on the left shows the standing sequence which starts by straightening the user s hips and legs before raising them to a standing position This sequence minimises pressure on the user s knees The symbol on the right shows the standing sequence which raises the user directly from a sitting position Seat lift t The seat rises when the toggle switch is moved for ward and lowers when the switch is moved back Back rest angle lt P The back rest will slope back when the toggle switch is moved backwards and forwards when it is moved forwards 22 User Manual VS Design and function Design and function Leg rest angle The leg rest moves out when the toggle switch is moved forwards and in when the toggle switch is moved back Seat angle The seat will slope back when t

OWNER`S MANUAL Seat system for Power Wheelchair

Contents

Download Pdf Manuals

Related Search

Related Contents