Home

Satellite Pro S850 User`s Manual

1. Disclaimer User s Manual TOSHIBA does not guarantee that the face recognition utility technology will be completely secure or error free TOSHIBA does not guarantee that the face recognition utility will accurately screen out unauthorized users at all times TOSHIBA is not liable for any failure or damage that might arise out of the use of the face recognition software or utility TOSHIBA ITS AFFILIATES AND SUPPLIERS SHALL HAVE NO RESPONSIBILITY FOR DAMAGE TO OR LOSS OF ANY BUSINESS PROFITS PROGRAMS DATA NETWORK SYSTEMS OR REMOVABLE STORAGE MEDIA ARISING OUT OF OR RESULTING FROM THE USE OF THE PRODUCT EVEN IF ADVISED OF THE POSSIBILITY THEREOF How to register the Face Recognition Data Take a picture for facial verification purposes and register the data needed when you log in To register the data needed when you log in follow the steps as described below 1 To launch this utility click Start gt All Programs gt TOSHIBA gt Tools amp Utilities gt Face Recognition The Registration screen is displayed for a logged in user whose face has not been registered The Management screen is displayed for a logged in user whose face has already been registered 2 Click Run as administrator in lower left of the Management screen and then click the Register button The Registration screen is displayed If you wish to practice click on the Next button in the Registration screen If you do not wish to practice cl
2. 1 To pop the disc tray partially open press the eject button Gently pull the disc tray out until it is fully opened When the disc tray pops open slightly wait a moment to make sure the disc has stopped spinning before pulling the disc tray fully open 2 The disc extends slightly over the sides of the disc tray so you can grasp it Gently lift out the disc 3 Push the center of the disc tray to close it Press gently until it locks into place How to remove disc when the disc tray will not open Pressing the eject button will not open the disc tray when the computer power is off If the power is off you can open the disc tray by inserting a slender object about 15 mm such as a straightened paper clip into the eject hole near the eject button Figure 3 8 Manual release with the eject hole 1 Eject hole Turn off the power before you use the eject hole If the disc is spinning when you open the disc tray the disc could fly off the spindle and cause injury Writable discs User s Manual This section describes the types of writable discs Check the specifications of your drive to see the types of discs it can write Use TOSHIBA Disc Creator to write compact discs CDs BH CD R discs can be written only once The recorded data cannot be erased or changed RH CD RW discs including multi speed CD RW discs high speed CD RW discs and ultra speed CD RW discs can be recorded more than once DVDs BH DVD R DVD R
3. 2 Click the Safely Remove Hardware and Eject Media icon on the Windows Taskbar 3 Click an eSATA device that you want to remove 4 Carefully pull an eSATA device s eSATA USB combo connector out from within the computer s eSATA USB combo port If you disconnect an eSATA device or turn off the power while the computer is accessing the drive you may lose data or damage an eSATA device or the drive Serial port The serial connector can be used to connect to RS 232C compatible devices RS 232C compatible devices include the following E Modem E Mouse E Printer Some models are equipped with a serial port To connect a serial port follow the steps as detailed below 1 Turn the computer s power off 2 Connect the serial connector to the serial port and tighten the screws on the left and right hand side Figure 3 22 Connecting the serial connector to the serial port 1 Serial port 2 Serial connector Security lock A security locks enable you to anchor your computer a desk or other heavy object in order to help prevent unauthorized removal or theft The computer has a security lock slot on its back side into which you can attach one end of the security cable while the other end attaches to a desk or similar User s Manual 3 46 object The methods used for attaching security cables differ from product to product Please refer to the instructions for the product you are using for more information Connecting the
4. The starting application from the button can be changed The TOSHIBA PC Diagnostic Tool will display basic system configuration information and allow the functionality of some of the computer s built in hardware devices to be tested The TOSHIBA Password utility allows you to set a password in order to restrict access to the computer The TOSHIBA Flash Cards provide a quick way to modify selected system functions This utility allows you to customize your hardware settings according to the way you work with the computer and the peripherals you use The TOSHIBA Accessibility utility provides support to movement impaired users when they need to use the TOSHIBA Hot key functions In use the utility allows you to make the FN key sticky that is you can press it once release it and they press one of the Function keys in order to access its specific function When set the FN key will remain active until another key is pressed User s Manual Fingerprint Utility TOSHIBA Face Recognition TOSHIBA VIDEO PLAYER Bluetooth Stack for Windows by Toshiba This product has a fingerprint utility installed for the purpose of enrolling and recognizing fingerprints which can then be linked to a username and password in order to remove the need to input these details from the keyboard Just by swiping an enrolled finger against the fingerprint sensor the following functions will be enabled m Logon to Windows and access a sec
5. 1 Disc tray 2 Eject button User s Manual 3 Lay the disc label side up in the disc tray Figure 3 7 Inserting a disc 1 Laser lens When the disc tray is fully opened the edge of the computer will slightly cover the disc tray Therefore you will need to turn the disc at an angle when you place it in the disc tray After seating the disc however make sure it lies flat BR Donot touch the laser lens or any portion of its surrounding casing as this could cause misalignment BR Prevent foreign objects from entering the drive Check the surface of the disc tray especially the area behind the front edge of the disc tray to make sure there are no such objects before closing the drive 4 Press gently at the center of the disc until you feel it click into place The disc should lie below the top of the spindle flush with the spindle base 5 Push the center of the disc tray to close it Press gently until it locks into place If the disc is not seated properly when the disc tray is closed the disc might be damaged Also the disc tray might not open fully when you press the eject button Removing discs To remove the disc follow the steps as detailed below Do not press the eject button while the computer is accessing the media drive Wait for the optical disc drive indicator to go out before you open the disc tray Also if the disc is spinning when you open the disc tray wait for it to stop before you remove it A
6. China CQC U S and Canada UL listed and CSA certified No 18 AWG Type SVT or SPT 2 Australia AS Japan DENANHO Europe Austria OVE Italy IMQ Belgium CEBEC The Netherlands KEMA Denmark DEMKO Norway NEMKO Finland FIMKO Sweden SEMKO France LCIE Switzerland SEV Germany VDE United Kingdom BSI In Europe two conductors power cord must be VDE type HOS5VVH2 F or HO3VVH2 F and for three conductors power cord must be VDE type HOSVV F For the United States and Canada two pin plug configuration must be a 2 15P 250V or 1 15P 125V and three pin plug configuration must be User s Manual B 1 User s Manual 6 15P 250V or 5 15P 125V as designated in the U S National Electrical code handbook and the Canadian Electrical Code Part II The following illustrations show the plug shapes for the U S A and Canada the United Kingdom Australia Europe and China Ir UL approved Australia OG AS approved Canada CSA approved United Kingdom e S ml D a H j A A N Ol Le BS approved Europe Approved by the appropriate agency China ac e CCC approved Appendix C Legal Footnotes This chapter states the Legal Footnotes information applicable to TOSHIBA computers Non applicable Icons CPU User s Manual Certain computer chassis are designed to accommodate all possible configurations for an entire product series Therefore please
7. Connect the AC adaptor and replace the battery taking care to ensure that it is securely seated in the computer Check the Battery indicator if it does not glow allow the computer to charge the battery for at least twenty minutes If the Battery indicator starts to glow after this period allow the battery to continue to charge for at least another twenty minutes before turning on the computer However if the indicator still does not glow the battery may be at the end of its operating life and should be replaced However if you do not believe the battery is at the end of its operating life you should speak to TOSHIBA Support Battery doesn t If you frequently recharge a partially charged power the computer battery the battery might not charge to its full as long as expected potential in these instances you should fully discharge the battery and then attempt to charge it again Check the Power saver option under Select a power plan in the Power Options User s Manual 6 6 Real Time Clock Problem Procedure The following The charge in the Real Time Clock RTC battery message is has run out you will need to set the date and time displayed on the in the BIOS setup application by using the screen following steps RTC battery is 1 Press and hold the F2 key and then turn on low Check the computer the BIOS setup utility will load system Then 2 Set the date in the System Date field press F2 key 3 Set the t
8. Problem You cannot access a disc in the drive Procedure Make sure the drive s disc tray is securely closed Press gently until it clicks into place Open the disc tray and make sure the disc is properly seated It should lie flat with the label facing up A foreign object in the disc tray could block laser light from reading the disc Make sure there is no obstruction Remove any foreign object Check whether the disc is dirty If it is wipe it with a clean cloth dipped in water or a neutral cleaner Refer to the Media care section in Chapter 3 for details on cleaning For further information please refer to Chapter 3 Operating Basics Problem Memory media card error occurs You cannot write to a memory media card You cannot read a file PC Card For further information please refer to Chapter 3 Operating Basics User s Manual Procedure Remove the memory media card from the computer and then reinsert it in order to ensure it is firmly connected If the problem persists then you should refer to the documentation supplied with your memory media card for further information Remove the memory media card from the computer and check to ensure that it is not write protected Check to ensure the required file is actually on the memory media card that is inserted into the computer If you are still unable to resolve the problem contact TOSHIBA Support Problem PC Card error occurs Po
9. Supervisor Password If you set a Supervisor Password some functions might be restricted when a user logs on with the User Password To set a Supervisor Password Start gt All Programs gt TOSHIBA gt Support amp Recovery gt TOSHIBA Assist gt SECURE gt Supervisor password This utility lets you do the following BH Register or delete the Supervisor Password E Specify restrictions for general users Starting the computer by password User s Manual If you have already registered a password there are several ways to start the computer BR Swipe your fingerprint on the sensor if you have already registered the fingerprint with the Fingerprint utility and enabled Fingerprint System Pre Boot Authentication If you would not like to swipe your finger or cannot authenticate the fingerprint for some reasons push the BACK SPACE key to skip the fingerprint authentication screen You can try to swipe the fingerprint up to five times If you failed fingerprint authentication five times you must enter the password manually to start the computer BR Enter the password manually The password is necessary only if the computer was turned off in boot mode or Hibernation Mode It is not needed in Sleep Mode and Restart To enter a password manually follow the steps as detailed below 1 Turn on the power as described in Chapter 1 Getting Started The following message will appear in the screen Password At this po
10. mercury Hg and or cadmium Cd defined in the Battery Directive 2006 66 EC then the chemical symbols for lead Pb mercury Hg and or cadmium Cd will appear below the crossed out wheeled dust bin symbol By participating in separate collection of batteries you will help to assure the proper disposal of products and batteries and thus help to prevent potential negative consequences for the environment and human health For more detailed information about the collection and recycling programmes available in your country please visit our website http eu computers toshiba europe com or contact your local city office or the shop where you purchased the product XV A These symbols may not stick depending on the country and region where you purchased Following information is only for India A The use of this symbol indicates that this product may not be treated as household waste By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product For more detailed information about recycling of this product please visit our website http www toshiba india com or contact call center 1800 200 8674 These symbols may not stick depending on the country and region where you purchased Disposing of the computer and the computer s batteries BH Discar
11. D f you are operating the computer on battery power you can lengthen the overall operating time by turning it off into Hibernation Mode Sleep Mode will consume more power while the computer is off Sleep Mode limitations Sleep Mode will not function under the following conditions BH Power is turned back on immediately after shutting down E Memory circuits are exposed to static electricity or electrical noise User s Manual 1 8 User s Manual Hibernation Mode The Hibernation Mode feature saves the contents of memory to the hard disk drive when the computer is turned off so that the next time it is turned on the previous state is restored Please note that the Hibernation Mode feature does not save the status of any peripheral devices connected to the computer m Save your data While entering Hibernation Mode the computer saves the contents of memory to the hard disk drive However for safety sake itis best to save your data manually BR Data will be lost if you remove the battery or disconnect the AC adaptor before the save is completed Wait for the Hard Disk Drive Optical Disc Drive eSATA indicator to go out BR Do not install or remove a memory module while the computer is in Hibernation Mode Data will be lost BR Do not switch to Hibernation Mode while transferring data to external media such as USB devices memory media or other external memory devices Data will be lost Benefits of Hibernation Mode The Hi
12. Media Access RH CSMA CA Collision Avoidance with Protocol Acknowledgment ACK Radio Characteristics Radio Characteristics of Wireless LAN module may vary according to BR Country region where the product was purchased BR Type of product Wireless communication is often subject to local radio regulations Although Wireless LAN wireless networking products have been designed for operation in the license free 2 4GHz and 5GHz band local radio regulations may impose a number of limitations to the use of wireless communication equipment Radio Frequency E Band 5GHz 5150 5850 MHz Revision a and n E Band 2 4GHz 2400 2483 5 MHz Revision b g and n The range of the wireless signal is related to the transmit rate of the wireless communication Communications at lower transmit range may travel larger distances BH The range of your wireless devices can be affected when the antennas are placed near metal surfaces and solid high density materials H Range is also impacted due to obstacles in the signal path of the radio that may either absorb or reflect the radio signal Bluetooth wireless technology User s Manual Some computers in this series have Bluetooth wireless communication function which eliminates the need for cables between electronic devices such as computers printers and mobile phones When it is enabled Bluetooth provides the wireless personal area network environment which is safe and trustworthy that is qui
13. To avoid risk of lost data always make back up copies of data by periodically storing it on an external storage medium For optimum performance use your computer product only under recommended conditions Read additional restrictions in your product documentation Contact TOSHIBA technical service and support refer to Chapter 6 Troubleshooting for more information 64 Bit Computing 64 bit processors are designed to take advantage of 32 and 64 bit computing 64 bit computing requires that the following hardware and software requirements are met BH 64 bit Operating System H 64 bit CPU Chipset and BIOS Basic Input Output System RH 64 bit Device drivers RH 64 bit applications Certain device drivers and or applications may not be compatible with a 64 bit CPU and therefore may not function properly Memory Main System Part of the main system memory may be used by the graphics system for graphics performance and therefore reduce the amount of main system memory available for other computing activities The amount of main system memory allocated to support graphics may vary depending on the graphics system applications utilized system memory size and other factors If your computer is configured with more than 3GB memory the memory might be displayed as approximately 3GB only depending on the computer s hardware specifications This is correct because the operating system usually displays the available memory instead of
14. if required 9 Turn your computer over Using the Hard Disk Drive HDD Protection This computer has a function for reducing the risk of damage on the hard disk drive Using an acceleration sensor built into the computer TOSHIBA HDD Protection detects vibration shocks and similar signs of movement of the computer and automatically moves the Hard Disk Drive head to a safe position to reduce the risk of damage that could be caused by head to disk contact 7 m The TOSHIBA HDD Protection function does not guarantee that the J hard disk drive will not be damaged BR During audio video playback when the computer detects a shock or vibration and the hard disk drive s head is parked the playback might be temporarily interrupted BH TOSHIBA HDD Protection cannot be used in models that are equipped with SSD When vibration is detected a message will be displayed on the screen and the icon in the Taskbar notification area will change to the protection state This message is displayed until the OK button is pressed or 30 seconds pass When vibration subsides the icon returns to the normal state Taskbar icon ES Normal TOSHIBA HDD Protection is enabled Protection TOSHIBA HDD Protection is active The hard disk drive head is in a safe position a OFF TOSHIBA HDD Protection is disabled x TOSHIBA HDD Protection Properties You can change the TOSHIBA HDD Protection settings by using the TOSHIBA HDD Protection Properties
15. 3 5 FN F1 Lock 3 5 FN F10 Arrow mode 3 4 FN F11 Numeric mode 3 4 FN F12 ScrLock 3 4 FN F2 Power Plan 3 5 FN F3 Sleep 3 5 FN F4 Hibernate 3 5 FN F5 Output 3 5 FN F6 Brightness Down 3 5 FN F7 Brightness Up 3 5 FN F8 Wireless 3 5 FN F9 Touch Pad 3 6 FN space Zoom 3 6 FN TAB ODD Function keys 3 3 Graphics controller 2 12 Hard disk drive automatic power off 4 7 HDD Protection 4 26 Heat dispersal 3 50 4 8 K M Hibernation Mode 1 9 4 9 Hot keys 4 7 HW Setup accessing 4 18 Boot 4 19 display 4 19 general 4 18 keyboard 4 20 LAN 4 21 SATA 4 23 USB 4 22 window 4 18 Keyboard FN Sticky key 3 6 Function keys F1 F12 3 3 Hot key functions 3 4 problems 6 7 Windows special keys 3 6 Keypad overlay Arrow mode 3 7 Numeric mode 3 7 temporarily using normal keyboard overlay on 3 7 temporarily using overlay overlay off 3 7 turning on the overlays 3 6 LAN cable types 3 31 connecting 3 31 problems 6 18 Media care Card care 3 37 Index 2 User s Manual Memory card care 3 37 Memory additional 3 47 installing 3 39 problems 6 15 removing 3 42 memory media card inserting 3 37 removing 3 38 Memory media slot 3 35 Modem connecting 3 26 disconnecting 3 27 problems 6 17 6 18 properties menu 3 25 region selection 3 24 Moving the computer 3 50 MultiMediaCard removing 3 38 Optical disc drive using writing Password
16. AC adaptor can cause damage to the computer CH Modem jack The modem jack lets you use a modular cable to connect the modem directly to a telephone line Some models are equipped with a modem jack K LAN jack This jack lets you connect to a LAN The adaptor has built in support for Ethernet LAN 10 megabits per second 10BASE T Fast Ethernet LAN 100 megabits per second 100BASE TX or Gigabit Ethernet LAN 1000 megabits per second 1000BASE T Refer to chapter 3 Operating Basics for details m Do not connect any cable other than a LAN cable to the LAN jack It could cause damage or malfunction Donot connect the LAN cable to a power supply It could cause damage or malfunction LAN active indicator This indicator may glow orange when the orange computer is connected to a LAN and the LAN is functioning properly Link indicator green This indicator may glow green when the computer is connected to a LAN and the LAN is functioning properly Underside The following figure shows the underside of the computer You should ensure that the display is closed before the computer is turned over to avoid causing any damage User s Manual 2 6 Figure 2 5 The underside of the computer 1 Battery lock 2 Battery release latch 3 Battery pack 4 Memory module slot Product appearance depends on the model you purchased 1 Battery lock Slide th
17. EXCEPT FOR o DEVIATIONS PURSUANT TO LASER NOTICE NO 50 DATED JUNE 24 2007 Kk CLASS 1 LASER PRODUCT LASER KLASSE 1 TEAC Corporation 1 47 OCHIAI TAMA SHI TOKYO JAPAN User s Manual xviii Precautions User s Manual CLASS 1 LASER PRODUCT LASER KLASSE 1 PRODUKT TO EN 60825 1 IGA AVF Ba CAUTION This appliance contains a laser system and is classified as a CLASS 1 LASER PRODUCT To use this model properly read the instruction manual carefully and keep this manual for your future reference In case of any trouble with this model please contact your nearest AUTHORIZED service station To prevent direct exposure to the laser beam do not try to open the enclosure xix Preface Congratulations on your purchase of this computer This powerful notebook computer provides excellent expansion capability includes multimedia functionality and is designed to provide years of reliable high performance computing This manual tells how to set up and begin using your computer It also provides detailed information on configuring your computer basic operations and care using optional devices and troubleshooting Conventions This manual uses the following formats to describe identify and highlight terms and operating procedures Abbreviations On first appearance and whenever necessary for clarity abbreviations are enclosed in parentheses following their definition
18. For example Read Only Memory ROM Acronyms are also defined in the Glossary Icons Icons identify ports dials and other parts of your computer The indicator panel also uses icons to identify the components it is providing information on Keys The keyboard keys are used in the text to describe many computer operations A distinctive typeface identifies the key top symbols as they appear on the keyboard For example ENTER identifies the ENTER key Key operation Some operations require you to simultaneously use two or more keys We identify such operations by the key top symbols separated by a plus sign For example CTRL C means you must hold down CTRL and at the same time press C If three keys are used hold down the first two and at the same time press the third ABC When procedures require an action such as clicking an icon or entering text the icon s name or the text you are to type in is represented in the typeface you see to the left User s Manual RX Messages Messages are used in this manual to bring important information to your attention Each type of message is identified as shown below Indicates a potentially hazardous situation which could result in death or serious injury if you do not follow instructions rg Pay attention A caution informs you that improper use of equipment or failure to follow instructions may cause data loss or damage your equipment 1 Please read A note is a hint or
19. Hard Disk Drive HDD Capacity LCD 1 Gigabyte GB means 10 1 000 000 000 bytes using powers of 10 The computer operating system however reports storage capacity using powers of 2 for the definition of 1GB 2 1 073 741 824 bytes and therefore shows less storage capacity Available storage capacity will also be less if the product includes one or more pre installed operating systems such as Microsoft Operating System and or pre installed software applications or media content Actual formatted capacity may vary Over a period of time and depending on the usage of the computer the brightness of the LCD screen will deteriorate This is an intrinsic characteristic of LCD technology Maximum brightness is only available when operating in AC power mode Screen will dim when the computer is operated on battery power and you may not be able to increase the brightness of the screen Graphics Processing Unit GPU Graphics Processing Unit GPU performance may vary depending on product model design configuration applications power management settings and features utilized GPU performance is only optimized when operating in AC power mode and may decrease considerably when operating in battery power mode Total Available Graphics Memory is the total of as applicable Dedicated Video Memory System Video Memory and Shared System Memory Shared System Memory will vary depending on system memory size and other factors Wirele
20. How much charge the battery contained to begin with How you use optional devices such as a USB device to which the battery supplies power Whether you enable Sleep Mode which can conserve battery power if you are frequently turning the computer off and on Where you store your programs and data Whether you close the display panel when you are not using the keyboard closing the display saves power The environmental temperature operating time decreases at low temperatures The condition of the battery terminals you should always ensure the terminals stay clean by wiping them with a clean dry cloth before installing the battery pack Batteries exhausted time Refer to User Information Guide about battery exhausted time Extending battery life User s Manual To maximize the life of your battery packs At least once a month disconnect the computer from a power source and operate it on battery power until the battery pack fully discharges Before doing so follow the steps as detailed below 1 Turn off the computer s power 2 Disconnect the AC adaptor and turn on the computer s power if it does not turn on then go to Step 4 3 Operate the computer on battery power for five minutes If you find that the battery pack has at least five minutes of operating time continue operating until the battery pack is fully discharged however if the Battery indicator flashes or there is some other warning to indicate a low bat
21. In addition to the information in this section please also refer to the documentation supplied with your audio device User s Manual 6 15 Problem Procedure No sound is heard Adjust the volume To increase the volume click the volume up button and to decrease it click the volume down button Check the software volume settings Please check to see if Mute is turned to Off Check to make sure the headphone connection is secure Check within the Windows Device Manager application to ensure the sound device is enabled and that the device is properly working Annoying sound is In this instance you may be experiencing feedback heard from either the internal microphone or an external microphone connected to the computer please refer to Sound System in Chapter 3 Operating Basics for further information Volume cannot be adjusted during Windows start up or shut down If you are still unable to resolve the problem contact TOSHIBA Support External monitor Please also refer to Chapter 3 Operating Basics and to the documentation supplied with your monitor for further information Problem Procedure Monitor does not After confirming that the monitor s power switch is turn on on you should check the connections to make sure that the power cord adaptor is firmly connected to the monitor and to a working power outlet User s Manual 6 16 Problem No display Display error occurs Modem T User s Manual Procedur
22. USB Legacy Emulation mode Keep foreign metal objects such as screws staples and paper clips out of the Memory media slot ExpressCard PC Card slot eSATA USB combo port and USB port Foreign metal objects can create a short circuit which can cause damage and fire possibly resulting in serious injury Back eee User s Manual The following figure shows the Computers back Figure 2 4 The back of the computer FOSMeke eae me 4 1 Security lock slot 5 Modem jack 2 External RGB monitor port 6 LAN jack 3 Serial port 7 LAN active indicator orange 4 DC IN 15V jack 8 Link indicator green Provided with some models Product appearance depends on the model you purchased Security lock slot A security cable can be attached to this slot and then connected to a desk or other large object in order to deter theft of the computer External RGB monitor This port provides 15 pin analog RGB port port This port allows you to connect an external RGB monitor to the computer Serial port Use this 9 pin port to connect serial devices such as an external modem serial mouse or serial printer Some models are equipped with a serial port DC IN 15V jack The AC adaptor connects to this jack in order to DIN JV power the computer and charge its internal batteries Please note that you should only use the model of AC adaptor supplied with the computer at the time of purchase using the wrong
23. Windows Control Panel If the call is going through a Private Branch Exchange PBX take care to ensure that the communication application s tone dial detection feature is disabled Problem Procedure You place a call but Make sure that the settings are correct within your a connection can t communication application be made After making a call Ensure that the communication application s tone you can t hear a ring or pule dialling selection feature is set correctly Communication is The computer will automatically cut off cut off unexpectedly communication when connection with the carrier is not successful for a set time interval try lengthening this time interval within your communication application A CONNECT display Ensure that the communication application s error is quickly replaced control feature is set correctly by NO CARRIER Character display When transmitting data you should ensure that the becomes garbled parity bit and stop bit settings correspond with during a those of the remote computer you should check communication the flow control and communication protocol settings within your communication application You cannot receive Ensure that the communication application s rings an incoming call before auto answer feature is set correctly If you are still unable to resolve the problem contact your reseller dealer or service provider LAN Problem Procedure Cannot access LAN Check for a firm c
24. and Touch Pad while the display panel display panel has been closed You should try to remove the marks by gently wiping the display panel with a clean dry cloth or if this fails with a good quality LCD screen cleaner In this latter instance you should always follow the instructions with the screen cleaner and always ensure you let the display panel dry properly before closing it Hard disk drive Problem Procedure Computer does not Check to see whether there is a disc in the optical boot from hard disk disc drive if so remove it and try to start the drive computer again If this has no effect check the Boot Priority setting within the TOSHIBA HW Setup utility please refer to the Boot Setting section in Chapter 4 Utilities amp Advanced Usage for further information Slow performance The files on the hard disk drive may be fragmented in this instance you should run the disk Defragmentation utility to check the condition of your files and the hard disk drive Please refer to the operating system s documentation or online Help File for further information on operating and using the Defragmentation utility As a last resort you should reformat the hard disk drive and then reload the operating system and all other files and data If you are still unable to resolve the problem contact TOSHIBA Support Optical Disc Drive For more information refer to Chapter 3 Operating Basics User s Manual 6 8 Memory Media Card
25. and should be replaced only by your dealer or by a TOSHIBA service representative The battery can explode if not properly replaced used handled or disposed Dispose of the battery as required by local ordinances or regulations i Charge the battery pack only in an ambient temperature between 5 and 35 degrees Celsius Otherwise the electrolyte solution might leak battery pack performance might deteriorate and the battery life might be shortened m Never install or remove the battery pack without first turning off the power and disconnecting the AC adaptor Never remove the battery pack while the computer is in Sleep Mode Data could be lost Never remove the battery pack while the Wake up on LAN function is enabled Data will be lost Before you remove a battery pack disable the Wake up on LAN function Charging the batteries User s Manual When the power in the battery pack becomes low the Battery indicator will flash orange to indicate that only a few minutes of battery power remain If you continue to use the computer while the Battery indicator flashes the computer will enable Hibernation Mode so that you do not lose any data and automatically turn itself off You must recharge a battery pack when it becomes discharged Procedures To recharge a battery pack while it is installed in the computer connect the AC adaptor to the DC IN 15V jack and plug the other end into a working outlet the Battery indicator will g
26. battery pack is the primary power source However your computer also has a number of other power resources including an intelligent power supply and a Real Time Clock RTC battery all of which are interrelated with any one having the ability to produce apparent power problems Overheating power down If the processor s temperature reaches an unacceptably high level with either setting the comp uter will automatically shuts down to prevent any damage in this instance all unsaved data in memory will be lost Problem Computer shuts down and DC IN indicator blinks orange Computer shuts down and its DC IN indicator is flashing green Procedure Leave the computer off until the DC IN indicator stops blinking It is recommended to leave the computer off until the interior reaches room temperature even though the DC IN indicator stops blinking If the computer has reached room temperature and it still does not start or if it starts but shuts down quickly contact TOSHIBA Support This indicates a problem with the heat dispersal system you should contact TOSHIBA Support User s Manual AC power If you have trouble turning on the computer with the AC adaptor connected you should check the status of the DC IN indicator Please refer to Chapter 5 Power and Power Up Modes for further information Problem Procedure AC adaptor doesn t Check the connections to make sure that the power the computer power
27. business interruption that may be caused by the change or loss of the recorded contents E Damage that may be caused by using third party equipment or software Given the technological limitations of current optical disc writing drives you may experience unexpected writing or rewriting errors due to disc quality or problems with hardware devices In view of this it is good practice to make two or more copies of important data in case of any undesired change or loss of the recorded contents Before writing or rewriting User s Manual E Based on TOSHIBA s limited compatibility testing we suggest the following manufacturers of disc media however it must be noted that disc quality can affect writing or rewriting success rates Please also be aware that in no event does TOSHIBA guarantee the operation quality or performance of any disc User s Manual CD R TAIYO YUDEN CO Ltd MITSUBISHI KAGAKU MEDIA CO LTD CD RW Multi Speed High Speed and Ultra Speed MITSUBISHI KAGAKU MEDIA CO LTD DVD R DVD Specifications for Recordable Disc for General Version 2 0 TAIYO YUDEN Co Ltd for 8x and 16x speed media MITSUBISHI KAGAKU MEDIA CO LTD for 8x and 16x speed media Hitachi Maxell Ltd for 8x and 16x speed media DVD R DL MITSUBISHI KAGAKU MEDIA CO LTD for 4x and 8x speed media DVD R MITSUBISHI KAGAKU MEDIA CO LTD for 8x and 16x speed media TAIYO YUDEN CO Ltd for 8x and 16x speed media DVD R
28. connected stop using the external device because its current is over the acceptable value of this computer Some external devices may not be able to use the Sleep and Charge function In this case please try one or more of the following methods BR Turn OFF the computer while external devices are connected BH Connect external devices after turning OFF of the computer If this function can not be still used change the setting to disable the function and stop using this function Problem Procedure The battery depletes If Sleep and Charge function is enabled the quickly even when computer s battery will discharge during turned OFF the hibernation or when the computer is turned off power of the Connect the AC adaptor to the computer or disable computer the Sleep and Charge function External devices Some external devices may not work when connected to the connected to a compatible port if the Sleep and compatible ports do Charge function is enabled not work when connected to a compatible port Reconnect the external device after turning the computer ON If the external device still does not work connect device to an USB port that does not have the Sleep and Charge function compatible icon 4 or change to disable the Sleep and Charge function The USB Wakeup When System ON CDP Charge Mode or USB function does not Sleep and Charge function is enabled the USB work WakeUp function does not work for por
29. following questions in mind Which part of the computer is not operating properly keyboard hard disk drive display panel touch pad touch pad control buttons as each device will produce different symptoms Check the options within the operating system to ensure that its configuration is set properly What appears on the display Does it display any messages or random characters Make a screenshot of the current display and if possible look up the messages in the documentation included with the computer software or operating system Check that all connecting cables are correctly and firmly attached as loose cables can cause erroneous or intermittent signals Do any indicators light if so which ones what color are they and do they stay on or blink Write down what you see Do you hear any beeps if so how many are they long or short and are they high pitched or low pitched In addition is the computer making any unusual noises Write down what you hear Record your observations so you can describe them in detail to TOSHIBA Support Software The problems may be caused by your software or disk If you cannot load a software package the media may be damaged or the program might be corrupted in these instances try loading another copy of the software if possible If an error message appears while you are using a software package you should refer to the documentation supplied with it as this will usually include a problem
30. graphics as designated by the on screen pointer Fingerprint Sensor This sensor enables you to enroll and recognize a fingerprint For detailed information on Fingerprint Sensor refer to the Using the Fingerprint Sensor section in Chapter 3 Operating Basics Some models are equipped with a Fingerprint Sensor Internal Hardware Components This section describes the internal hardware components of your computer The actual specifications may vary depending on the model you purchased CPU The processor type varies depending on model To check which type of processor is included in your model open the TOSHIBA PC Diagnostic Tool Utility by clicking Start gt All Programs gt TOSHIBA gt Support amp Recovery gt PC Diagnostic Tool Legal Footnote CPU For more information regarding CPU please refer to the Legal Footnotes section in Appendix C Hard Disk Drive or The size of the hard disk drive varies depending Solid State Drive on the model To check which type of HDD SSD is included in your model open the TOSHIBA PC Diagnostic Tool Utility by clicking Start gt All Programs gt TOSHIBA gt Support amp Recovery gt PC Diagnostic Tool Please note that part of the hard disk s overall capacity is reserved as administration space 7 nthis manual the word HDD or Hard disk drive also refers to the d SSD unless otherwise stated User s Manual 2 11 User s Manual m SSD is a large capacity stor
31. handling and maintenance Cleaning the computer User s Manual To help ensure long trouble free operation keep the computer free of dust and dirt and use care with all liquids around it BH Be careful not to spill liquids into the computer If the computer does get wet turn the power off immediately and let the computer dry completely in these circumstance you should get the computer inspected by an authorized service provider in order to assess the scope of any damage BH Clean the plastics of the computer using a slightly water dampened cloth 3 49 A You can clean the display screen by spraying a small amount of glass cleaner onto a soft clean cloth and then wiping the screen gently with the cloth Never spray cleaner directly onto the computer or let liquid run into any part of it Never use harsh or caustic chemical products to clean the computer Moving the computer While the computer is designed for flexible day to day usage you should exercise a few simple precautions when moving it in order to help ensure trouble free operation H Before moving the computer it is recommended that you change the setting associated with the Hard Disk Drive Protection feature Please refer to the section Heat dispersal in this chapter for further information BR Make sure all disk disc activity has ended before moving the computer E Turn off shut down the computer BR Disconnect the AC adaptor and all peripherals be
32. or disable the internal USB 3 0 controller If Disabled is selected the internal USB 3 0 port s on the computer will work as USB 2 0 port s which will save power Enabled Enables the internal USB 3 0 controller Default Disabled Disables the internal USB 3 0 controller System ON CDP Charge Mode Enabled Rapid USB battery charge at maximum 1 5A while PC is powered On Disabled Conventional USB battery charge while PC is powered On Default When System ON CDP Charge Mode is enabled your computer can supply USB bus power DCS5V 1 5A to the compatible ports while the computer is turned on The System ON CDP Charge Mode may not work with certain external devices even if they are compliant with the USB specifications In those cases use a USB port without USB Sleep and Charge function or disable System ON CDP Charge Mode It is recommended that AC adaptor be connected to the computer while using the System ON CDP Charge Mode When your computer battery capacity is too low to continue System ON CDP Charge Mode may not work In those cases connect the AC adaptor and reboot the computer Never use USB cables not supporting this feature when System ON CDP Charge Mode DC5V 1 5A is enabled Always use the USB cable that was included with your USB device When System ON CDP Charge Mode or USB Sleep and Charge function is enabled the USB Wakeup function will not work In that case use a USB p
33. solving section or a summary of error messages Next you should check any error messages against the operating system documentation A Hardware If you cannot find a software problem you should then check the setup and configuration of your hardware First run through the items in the preliminary checklist as described previously then if you still cannot correct the problem try to identify the source the next section provides checklists for individual components and peripherals Before using a peripheral device or application software that is not an authorized TOSHIBA part or product make sure the device or software can be used with your computer Use of incompatible devices may cause injury or may damage your computer If something goes wrong User s Manual Your program stops responding If you are working with a program that suddenly freezes all operations chances are the program has stopped responding You can exit the failed program without shutting down the operating system or closing other programs To close a program that has stopped responding 1 Press CTRL ALT and DEL simultaneously once then click Start Task Manager The Windows Task Manager window appears 2 Click the Applications tab If a program has stopped responding the words not responding appear beside its name in the list 3 Select the program you want to close then click End Task Closing the failed program should allow you to continue
34. specifications and requirements in the country of use Failure to do so could result in a fire or electric shock possibly resulting in serious injury The supplied power cord conforms to safety rules and regulations in the region the product is bought and should not be used outside this region For use in other regions please buy power cords that conform to safety rules and regulations in the particular region Do not use a 3 pin to 2 pin conversion plug When you connect the AC adaptor to the computer always follow the Steps in the exact order as described in the User s Manual Connecting the power cable to a live electrical outlet should be the last step otherwise the adaptor DC output plug could hold an electrical charge and cause an electrical shock or minor bodily injury when touched As a general safety precaution avoid touching any metal parts Never place your computer or AC adaptor on a wooden surface furniture or any other surface that could be marred by exposure to heat since the computer base and AC adaptor s surface increase in temperature during normal use Always place your computer or AC adaptor on a flat and hard surface that is resistant to heat damage Refer to the enclosed Instruction Manual for Safety and Comfort for detailed precautions and handling instructions 1 Connect the power cord to the AC adaptor Figure 1 1 Connecting the power cord to the AC adaptor 2 pin plug ai Either a 2 pin or 3 pin ad
35. sure all disk disc activity has stopped before removing the disk disc BR Make sure the Hard Disk Drive Optical Disc Drive eSATA indicator is off If you turn off the power while a disk disc is being accessed you may lose data or damage the disk BR Never turn off the power while an application is running Doing so could cause loss of data BR Never turn off the power disconnect an external storage device or remove storage media during data read write Doing so can cause data loss 3 Click Start D Gef T User s Manual 4 Click the Shut down button E 5 Turn off any peripheral devices connected to your computer Do not turn the computer or peripheral devices back on immediately wait a short period to avoid any potential damage Sleep Mode If you have to interrupt your work you are able to turn off the power without exiting from your software by placing the computer into Sleep Mode In this mode data is maintained in the computer s main memory so that when you turn on the power again you can continue working right where you left off When you have to turn off your computer aboard an aircraft or in places where electronic devices are regulated or controlled always completely shut down the computer This includes turning off any wireless communication functionalities and cancelling settings that reactivate the computer automatically such as a timer recording function Failure to completely shut down the compu
36. that applies the copy protection system Media care Observe the following precautions when handling the card BR Do not twist or bend cards Do not expose cards to liquids or store in humid areas or lay media close to containers of liquid Do not touch the metal part of a card or expose it to liquids or let it get dirty m After using card return it to its case The card is designed so that it can be inserted only one way Do not try to force the card into the slot E Do not leave a card partially inserted in the slot Press the card until you hear it click into place BH Get the write protect switch to the lock position if you do not want to record data E Memory cards have a limited lifespan so it is important to backup important data Do not write to a card if the battery power is low Low power could affect writing accuracy m Do not remove a card while read write is in progress je For more details on using memory cards see manuals accompanying the T cards About the write protect The memory media cards have a function for protect BH SD Card SD memory card SDHC memory card and SDXC memory card E Memory Stick Memory Stick Memory Stick PRO Memory Stick Duo Memory Stick PRO Duo Memory Stick Micro AN Set the write protect switch to the lock position if you do not want to record data Inserting a memory media The following instructions apply to all types of supported media devices To i
37. the on screen pointer to go Figure 3 1 Touch Pad and Touch Pad control buttons 1 Touch Pad 3 Touch Pad control buttons 2 Fingerprint Sensor Provided with some models The two buttons below the Touch Pad are used like the buttons on a standard mouse press the left button to select a menu item or to manipulate text or graphics designated by the pointer and press the right button to display a menu or other function depending on the software you are using The Keyboard User s Manual The computer s keyboard layouts are compatible with a 104 105 key enhanced keyboard by pressing some keys in combination all of the 104 105 key enhanced keyboard functions can be performed on the computer The number of keys available on your keyboard will depend on which country region your computer is configured for with keyboards being available for numerous languages In use there are six different types of keys specifically typewriter keys function keys soft keys Hot keys Windows special keys and the keypad overlay Never remove the key caps on your keyboard Doing so could cause damage to the parts under the key caps Keyboard indicators A4 size keyboard The following figures show the positions of the CAPS LOCK indicator and the keypad overlay indicators which show the following conditions m When the CAPS LOCK indicator glows the keyboard will produce capitals when any letter is typed D When the Arrow Mode in
38. the physical memory RAM built into the computer Various system components like the video adapter s GPU and PCI devices like Wireless LAN etc require their own memory space Since a 32 bit operating system cannot address more than 4GB of memory these system resources overlap the physical memory It is a technical limitation that the overlapped memory is not available to the operating system Even though some tools might display the actual physical memory built into your computer the memory available to the operating system will still be approximately 3GB only Computers configured with a 64 bit operating system can address 4GB or more of system memory Battery Life User s Manual Battery life may vary considerably depending on product model configuration applications power management settings and features utilized as well as the natural performance variations produced by the design of individual components Published battery life numbers are achieved on select models and configurations tested by TOSHIBA at the time of publication Recharge time varies depending on usage Battery may not charge while computer is consuming full power After going through many charge and discharge cycles the battery will lose its ability to perform at maximum capacity and will need to be replaced This is a normal phenomenon for all batteries To purchase a new battery pack see the accessories information that is shipped with your computer
39. the vents RB Always provide sufficient space around the computer BR Overheating your computer or AC adaptor could cause system failure computer or AC adaptor damage or a fire possibly resulting in serious injury Creating a computer friendly environment User s Manual Place the computer on a flat surface that is large enough for the computer and any other items you are using such as a printer Leave enough space around the computer and other equipment to provide adequate ventilation Otherwise they may overheat To keep your computer in prime operating condition protect your work area from BR Dust moisture and direct sunlight E Equipment that generates a strong electromagnetic field such as stereo speakers other than speakers that are connected to the computer or speakerphones BH Rapid changes in temperature or humidity and sources of temperature change such as air conditioner vents or heaters m Extreme heat cold or humidity BR Liquids and corrosive chemicals xxii Stress injury Carefully read the nstruction Manual for Safety and Comfort It contains information on the prevention of stress injuries to your hands and wrists that can be caused by extensive keyboard use It also includes information on work space design posture and lighting that can help reduce physical stress Heat injury BR Avoid prolonged physical contact with the computer If the computer is used for long periods its surface can b
40. will take a moment to save the current data in memory to the hard disk drive During this time the Hard Disk Drive Optical Disc Drive eSATA indicator will glow After you turn off the computer and the content of memory has been saved to the hard disk drive turn off the power to any peripheral devices Do not turn the computer or devices back on immediately Wait a moment to let all capacitors fully discharge Restarting the computer Certain conditions require that you reset the computer for example if m You change certain computer settings BH An error occurs and the computer does not respond to your keyboard commands If you need to restart the computer there are three ways this can be achieved BR Click Start point to the arrow icon Ek and then select Restart from the menu BH Press CTRL ALT and DEL simultaneously once to display the menu window then select Restart from the Shut down options BR Press the power button and hold it down for five seconds Once the computer has turned itself off wait between ten and fifteen seconds before turning the power on again by pressing the power button User s Manual 1 10 Chapter 2 The Grand Tour This chapter identifies the various components of the computer it is recommended that you become familiar with each before you operate the computer Legal Footnote Non applicable Icons For more information regarding Non applicable Icons please refer to the Legal Footn
41. working If it does not continue with the next step 4 Close the remaining programs one by one by selecting the program name then End Task Closing all programs should allow you to continue working If it does not power off your computer and then restart it The computer will not start Make sure you attached the AC adaptor and power cord cable properly or installed a charged battery If you are using the AC adaptor check that the wall outlet is working by plugging in another device such as a lamp Verify that the computer is on by looking at the Power indicator If the indicator is glowing the computer is on Also try turning the computer off and then on If you are using an AC adaptor verify that the computer is receiving power from the external power source by looking at the DC IN indicator If the indicator is glowing the source computer is connected to a live external power Hardware and system checklist This section discusses problems caused by your computer s hardware or attached peripherals Basic problems may occur in the following areas E Power m USB device m Keyboard E eSATA device E Internal display panel D Additional memory module BD Hard disk drive E Sound system Optical Disc Drive BH External monitor m PC Card m Modem m Memory Media Card m LAN E Pointing Device m Wireless LAN E Fingerprint Sensor H Bluetooth Power User s Manual When the computer is not plugged into an AC power outlet the
42. 1 Switzerland ATAAB ANO02 All other countries regions ATAAB ANO03 004 viii Specific switch settings or software setup are required for each network please refer to the relevant sections of the user guide for more details The hookflash timed break register recall function is subject to separate national type approvals It has not been tested for conformity to national type regulations and no guarantee of successful operation of that specific function on specific national networks can be given Japan regulations Region selection If you are using the computer in Japan technical regulations described in the Telecommunications Business Law require that you select the Japan region mode It is illegal to use the modem in Japan with any other selection Redial Up to two redial attempts can be made If more than two redial attempts are made the modem will return Black Listed If you are experiencing problems with the Black Listed code set the interval between redials at one minute or longer Japan s Telecommunications Business Law permits up to two redials on analogue telephones but the redials must be made within a total of three minutes The internal modem is approved by Japan Approvals Institute for Telecommunications Equipment mpgs e BEES A05 0413001 T This label is located on the module NE Pursuant to FCC CFR 47 Par
43. 11b g n IEEE802 11a n w56 Device Authorization User s Manual This device obtains the Technical Regulation Conformity Certification and it belongs to the device class of radio equipment of low power data communication system radio station stipulated in the Telecommunications Business Law of Japan E Intel Centrino Wireless N 6205 a b g n a b g Wireless LAN The Name of the radio equipment 62205ANHMW DSP Research Inc Approval Number D100944003 m Atheros AR938x Wireless Network Adapter a b g n a b g Wireless LAN The Name of the radio equipment AR5BHB116 DSP Research Inc Approval Number D101136003 E Intel Centrino Advanced N 6235 a b g n a b g Wireless LAN and Bluetooth The Name of the radio equipment 6235ANHMW DSP Research Inc Approval Number D111083003 BH Atheros AR9485WB EG Wireless Network Adapter Wireless LAN and Bluetooth The Name of the radio equipment AR5B225 DSP Research Inc Approval Number D110317003 The following restrictions apply BR Do not disassemble or modify the device E Do not install the embedded wireless module into other device Radio approvals for wireless devices Approved Countries Regions for Intel Centrino Wireless N 6205 a b g n a b g Atheros AR938x Wireless Network Adapter a b g n a b g Intel Centrino Advanced N 6235 a b g n a b g Atheros AR9485WB EG Wireless Network Adapter This equipment is approved to the radio standard by the count
44. C5V function that interfaces with the power ON OFF of the computer may always be in an operational state When there is a current overflow of the external devices connected to the compatible ports USB bus power DC5V supply may be stopped for safety reasons m When Sleep and Charge function is enabled the USB Wakeup function does not work for compatible ports In that case if there is a USB port that does not have the Sleep and Charge function compatible icon attach the mouse or keyboard to it If all USB ports have the Sleep and Charge function compatible icon change to disable Sleep and Charge function The USB Wakeup function will now work but the Sleep and Charge function will be disabled Metal paper clips or hair pins clips will generate heat if they come into contact with USB ports Do not allow USB ports to come into contact with metal products for example when carrying the computer in your bag Starting the TOSHIBA Sleep Utility To start the utility click Start gt All Programs gt TOSHIBA gt Tools amp Utilities gt Sleep Utility Enabling Sleep and Charge This utility can be used to enable and disable the Sleep and Charge function Select the Enable Sleep and Charge check box to enable this function for the compatible USB ports The default state is disabled Power supply mode settings Your PC has multiple charging modes so that many different USB devices can be supported for Sleep and Ch
45. DL MITSUBISHI KAGAKU MEDIA CO LTD for 8x speed media DVD RW DVD Specifications for Recordable Disc for Version 1 1 or version 1 2 Victor Company of Japan Ltd JVC for 2x 4x and 6x speed media MITSUBISHI KAGAKU MEDIA CO LTD for 2x 4x and 6x speed media DVD RW MITSUBISHI KAGAKU MEDIA CO LTD for 4x and 8x speed media DVD RAM DVD Super Multi drive only DVD Specifications for DVD RAM Disc for Version 2 0 Version 2 1 or Version 2 2 Panasonic Corporation for 3x and 5x speed media Hitachi Maxell Ltd for 3x and 5x speed media E Some types and formats of DVD R DL and DVD R DL discs may be unreadable m DISC created in DVD R DL format4 Layer Jump Recording cannot be read When writing or rewriting Please observe the following points while you write or rewrite data to a media BR Always copy data from the hard disk drive to the optical media do not use the cut and paste function as the original data will be lost if there is a write error Do not perform any of the following actions m Change users in the Operating Systems Operate the computer for any other function including such tasks as using a mouse or Touch Pad or closing opening the display panel BH Start a communication application such as a modem Apply impact or vibration to the computer BH Install remove or connect external devices including such items as ExpressCard PC Card memory media card USB device external mon
46. DVD R DL and DVD R DL discs can be written only once The recorded data cannot be erased or changed E DVD RW DVD RW and DVD RAM discs can be recorded more than once Writing discs A The TOSHIBA Disc Creator is provided as writing software with this computer You can use the DVD Super Multi drive to write data to either CD R CD RW DVD R DVD R DL DVD RW DVD R DVD R DL DVD RW or DVD RAM discs When writing information to media using an optical drive you should always ensure that you connect the AC adaptor to a live power socket It is possible that if data is written while powered by the battery pack the write process may sometimes fail due to low battery power in these instances data loss may occur Important message Before you write or rewrite to any of the media supported by the Optical Disc Drive please read and follow all of the setup and operating instructions in this section If you fail to do so you may find that the Optical Disc Drive may not function properly and you may fail to write or rewrite information successfully this may cause you to either lose data or incur other damage to the drive or media Disclaimer TOSHIBA does not bear responsibility for the following E Damage to any disc that may be caused by writing or rewriting with this product BR Any change or loss of the recorded contents of media that may be caused by writing or rewriting with this product or for any business profit loss or
47. Fingerprint Utility or click the Fingerprint utility icon in the Taskbar The Enroll screen is displayed Enter the current account password into the Windows Password field If no Windows password has been configured you will be asked to configure the new logon password Then click Next Click the non enrolled finger icon above the finger you want to register and then click Next The note for enrollment operation screen is displayed Confirm the message and then click Next The scanning practice screen is displayed You are able to practice swiping three times your finger to ensure you use the correct method When you have finished practicing swiping your finger click Next Swipe three times with the same finger If scanning of fingerprint succeeds Enrollment successfully Do you want to save this fingerprint message box will appear Click OK The following message will be displayed Its strongly recommended you enroll one more fingerprint Click OK and repeat Step 3 4 5 and 6 with another finger It is strongly recommended that you register 2 or more fingerprints You cannot enroll the same fingerprint more than once even ona different user account Delete the Fingerprint Data User s Manual Saved fingerprint data is stored in special non volatile memory inside the fingerprint sensor Therefore if you give the computer to someone else or dispose of it in any way the following process is recommended to delete your fin
48. Graphics controller The graphics controller maximizes display performance Legal Footnote Graphics Processing Unit GPU For more information regarding Graphics Processing Unit GPU please refer to the Legal Footnotes section in Appendix C Intel Rapid Start Technology User s Manual Some computers in this series support Intel Rapid Start Technology which enables the computer to change to Hibernation Mode from Sleep Mode after a specified period of time With the Intel Rapid Start Technology the Windows can rapidly resume from Hibernation Mode and battery life will be longer than when in Sleep Mode Intel Rapid Start Technology is enabled at factory default The computer will switch to Hibernation Mode after two hours of Sleep Mode You can use BIOS Setup to enable disable the function and change the specified time setting from Sleep Mode to Hibernation Mode 1 Press and hold the F2 key and then turn on the computer the BIOS setup utility will load 2 Select Advanced 3 Enable Disable Intel R Rapid Start Technology function 4 You can select the period of time from Sleep Mode to Hibernation Mode using Rapid Start Entry after If the Immediately option is selected the computer will switch to Hibernation Mode immediately after your computer goes into the Sleep Mode BR When Intel Rapid Start Technology is enabled switching from Sleep Mode to Hibernation Mode consumes power When you carry your computer ab
49. HIBA Assist is a graphical user interface that provides access to specific tools utilities and applications that make the use and configuration of the computer easier To access this utility click Start gt All Programs gt TOSHIBA gt Support amp Recovery gt TOSHIBA Assist TOSHIBA ConfigFree is a suite of utilities that improve the ease and control of communication devices and network connections help in the identification of communication problems and allow the creation of profiles if you need to switch between different locations and communication networks To access this utility click Start gt All Programs gt TOSHIBA gt Network amp Connectivity gt ConfigFree This computer is equipped with eco mode This mode slightly lowers performance of some devices to reduce electric power consumption You can realize measurable power savings by using it continuously TOSHIBA eco Utility helps you monitor your power savings by showing approximate real time power consumption Furthermore it shows approximate accumulated power consumption and approximate accumulated power savings when using eco mode daily weekly and monthly You can track power savings by using eco mode continuously To access this utility click Start gt All Programs gt TOSHIBA gt Tools amp Utilities gt eco Utility You can create discs in a number of formats including audio discs that can be played ona standard disc player
50. Power indicator to determine the power status of the computer the following indicator conditions should be noted Green Indicates power is being supplied to the computer and the computer is turned on Blinking orange Indicates that the computer is in Sleep Mode and that there is sufficient power available AC adaptor or battery to maintain this condition In Sleep Mode this indicator will turn on for one second and off for two seconds No light Under any other conditions the indicator does not light This section explains battery types use recharging methods and handling Battery types User s Manual The computer has different types of batteries Battery pack When the AC adaptor is not connected the computer s main power source is a removable lithium ion battery pack also referred to in this manual as the main battery You can purchase additional battery packs for extended 5 3 i use of the computer away from an AC power source although you should not change the battery pack while the AC adaptor is connected Before you remove the battery pack save your data and shut down the computer or place the computer into Hibernation Mode Please be aware that when placing the computer into Hibernation Mode the contents of memory will be saved to the hard disk drive although for safety sake it is best to also save your data manually Real Time Clock RTC battery The Real Time Clock RTC battery provides power for
51. Products that earn the ENERGY STAR prevent greenhouse gas emissions by meeting strict energy efficiency guidelines set by the US EPA and the EU Commission According to the EPA a computer meeting the new ENERGY STAR specifications will use between 20 and 50 less energy depending on how it is used Visit http www eu energystar org or http www energystar gov for more information regarding the ENERGY STAR Program xvii Optical disc drive safety instructions 2 Be sure to check the precautions at the end of this section T E The drive model employs a laser system To ensure proper use of this product please read this instruction manual carefully and retain for future reference Should the unit ever require maintenance contact an authorized service location m Use of controls adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure BR Toprevent direct exposure to the laser beam do not try to open the enclosure 1 Panasonic Precision Devices Co Ltd BR DVD SuperMulti with Double Layer Location of the required label SERIAL NO MANUFACTURED COMPLIES WITH FDARADIATION PERFORMANCE STANDARDS 21CFR SUBCHAPTER J GLASS 7 LASER PRODUCT D 2 TEAC BR DVD SuperMulti with Double Layer Location of the required label SERIAL NO MANUFACTURED THIS PRODUCT COMPLIES WITH 21 CFR 1040 10 AND 1040 11
52. R DVD R DL or DVD RW media if this is not the case then the source disc might not be backed up correctly When you back up a DVD R DVD R DL DVD RW DVD R DVD R DL or DVD RW disc be sure to use the same type of disc You cannot partially delete any data written to a CD RW DVD RW or DVD RW disc Data Verification User s Manual To verify that data has been written or rewritten correctly to a data disc you should follow the steps below before you begin the write rewrite process 1 2 G3 Click Start gt All Programs gt TOSHIBA gt Media amp Entertainment gt Disc Creator to access the TOSHIBA Disc creator utility Display the setting dialog box by one of the following two steps Click the Recording settings button for writing on the main toolbar in the Data CD DVD mode Select Settings for Each Mode gt Data CD DVD in the Settings menu Mark the Verify Written Data check box Select File Open or Full Compare mode 3 21 5 Click the OK button How to learn more about TOSHIBA Disc Creator Please refer to the Help files for additional TOSHIBA Disc Creator information TOSHIBA VIDEO PLAYER 3 Please be aware of the following limitations when you use the TOSHIBA VIDEO PLAYER You may not have the TOSHIBA VIDEO PLAYER depending on the model you purchased Notes on use User s Manual This software can only be used on Windows 7 RH TOSHIBA VIDEO PLAYER software is supported for play
53. TOSHIBA Leading Innovation gt gt gt User s Manual Satellite Pro 850 Series Table of Contents Chapter 1 Chapter 2 Chapter 3 Chapter 4 User s Manual Preface General Precautions Getting Started Equipment checklist eege Aces ties hie ete ees ee 1 1 GettING Started sssini naidu nananana aa Ni aeaaeae aa 1 2 The Grand Tour Front with the display closed ccsccsesereseeeeeeseeeeeeeeeensseeeeeseeneneseens 2 1 Internal Hardware Components ssssssnssusssnnnrennnrennrnnnnnnnnnnennnnnnnnnnnnee 2 11 Operating Basics Using the Touch Pad EE 3 1 The CY DOAN E 3 1 Using the Fingerprint Sensor s sssssssssesssnnnnennnrnnnnrnnnnnnnnnnnnnnnnnnnnnnnnennn 3 8 Optical dis drives viinien SEN ENEdeuN 3 14 TOSHIBA Disc Creator ccecccceeeeeeeeeeeeceeeeesenseeseeesneeeeeeeseneeeseeneneneenen 3 20 TOSHIBA VIDEO PLAYER ccscscseeeeeneeeeeeesseneneseeeeseeeeessnneneseensneeaeen 3 22 Modem ececceseeeeeecen ee eeeeeensecneeeseaeeeeeeaeeasaeeseseeeeseeeaessenneeeneeesusseaesnsonanenees 3 24 Wireless COMMUNICATIONS EEN 3 27 LAN eege 3 31 Optional devices ec eeseeeeeeeeeeeeseeeeenseeeeseeeneeeeeeeseseeeeseseeeeeeeesnnsenenees 3 32 ExpressCard ou cccecescceeeeceeeeeeeeeeeeeeeeeeesscneeeseeeeeeeeessecneseseeeseeseeeensonenenees 3 32 PG el EE 3 33 Memory media ccceeeceseeeeeeeeeeeeeeeeeeacceeeeseesueeneesesseneeeneensesseeeeneensneeees 3 35 Additional memory module 0 0 0 ececeeeteeeee
54. Using the TOSHIBA Face Recognition T TOSHIBA Face Recognition uses a face verification library to verify the face data of users when they log in to Windows The user can thus avoid having to enter a password or the like which makes the login process easier m TOSHIBA Face Recognition does not guarantee the correct identification of a user Changes to the likeness of a registrant such as hair style changes wearing a cap or wearing glasses may effect the recognition rates when such changes occur after the registrant had registered E TOSHIBA Face Recognition may incorrectly recognize faces that are similar to a registrant For high security purposes TOSHIBA Face Recognition is not a suitable substitute for Windows passwords When security is a high priority use your established Windows passwords to log in BR Bright background light and or shadows may prevent a registrant from being recognized correctly In that case log in using your Windows password If recognition of a registrant fails repeatedly refer to your computer documentation to learn ways to improve recognition performance m TOSHIBA Face Recognition records face data in a log when face recognition fails When transferring ownership or disposing of your computer please uninstall the application or delete all the logs created by the application For details on how to do this see help file m TOSHIBA Face Recognition can be used only in Windows Vista and Windows 7
55. VELY uo cceccecceseeeeceseeeeseeeeeeseeeeeneeeseseeeesnseeeeseeeeseeeseesnnsneeeees 4 28 Chapter 5 Power and Power Up Modes Power conditions eee ceceeee ee eee en eeeee ee eeeee esses seneeeseseeeeeeeeenseneeeseeneneneees 5 1 Monitoring of power condition ceccceeeeeeseeeeeeeeeeeeeeeeenseeeeeseeneneseeee 5 2 E CV 5 3 Power up Modes ceeeeceseeeeeeeeeeneseeeeeeaeeeeneesescceeseseneseseaeeaseeeeeseenenenaes 5 9 Panel power On Off cssscceccsesccncsecsvsseseas cotenesaeeceecssacentieessenneencotebescea cones 5 10 System automatic Sleep Hibernation cc ceecesseeesseeneeeeeneeeeeees 5 10 Chapter 6 Troubleshooting Problem solving PLOCeSS cccceeeeeseneeeeeeeeeeeeeeeseeneeeeeeseaseeeeesseneneseees 6 1 Hardware and system Checklist 2 ccccesseecceeeeeeeeeeeeeeeeeeeeeeeeeeeeees 6 4 TOSHIBA SUPPOSE 1cccceseecseteceesnteceneseedsnncnededdecensnedcunnneseusadeeteceedusneners 6 20 AppendixA Specifications AppendixB AC Power Cord and Connectors AppendixC Legal Footnotes AppendixD Information for Wireless Devices Index Glossary User s Manual iii Copyright 2012 by TOSHIBA Corporation All rights reserved Under the copyright laws this manual cannot be reproduced in any form without the prior written permission of TOSHIBA No patent liability is assumed with respect to the use of the information contained herein First edition April 2012 Copyright authority for music movies compute
56. able connection between the LAN jack and the LAN hub Wake up on LAN Make sure the AC adaptor is connected The does not work Wake up on LAN function consumes power even when the system is off If problems persist consult your LAN administrator Wireless LAN If the following procedures do not restore LAN access consult your LAN administrator For more information on wireless communication refer to Chapter 3 Operating Basics User s Manual 6 18 Problem Cannot access Wireless LAN Bluetooth For further information on Bluetooth wireless communication please refer to Chapter 3 Operating Basics User s Manual Problem Cannot access Bluetooth device Procedure Make sure the computer s Wireless communication function is on If problems persist contact your LAN administrator Procedure Check to ensure the computer s Wireless Communication function is on Check to ensure the Bluetooth Manager application is running on the computer and that power to the external Bluetooth device is turned on Check to ensure that no optional Bluetooth Adaptor is installed in the computer the built in Bluetooth hardware cannot operate simultaneously with another Bluetooth controller If you are still unable to resolve the problem contact TOSHIBA Support Recovery Media Problem The following message appears when executing Recovery Media Creator The Recovery Media Creator can not be launched because t
57. advice that helps you make best use of J your equipment Terminology This term is defined in this document as follows Start The word Start refers to the button in Windows 7 HDD or Hard disk Some models are equipped with a Solid State drive Drive SSD instead of a hard disk drive In this manual the word HDD or Hard disk drive also refers to the SSD unless otherwise stated User s Manual xxi General Precautions TOSHIBA computers are designed to optimize safety minimize strain and withstand the rigors of portability However certain precautions should be observed to further reduce the risk of personal injury or damage to the computer Be certain to read the general precautions below and to note the cautions included in the text of the manual Provide adequate ventilation Always make sure your computer and AC adaptor have adequate ventilation and are protected from overheating when the power is turned on or when an AC adaptor is connected to a power outlet even if your computer is in Sleep Mode In this condition observe the following RB Never cover your computer or AC adaptor with any object RB Never place your computer or AC adaptor near a heat source such as an electric blanket or heater RB Never cover or block the air vents including those located at the base of the computer m Always operate your computer on a hard flat surface Using your computer on a carpet or other soft material can block
58. age media which uses Solid State Memory in place of a magnetic disk of the hard disk Under certain unusual conditions of prolonged non use and or exposure to high temperatures the SSD may be vulnerable to data retention errors Legal Footnote Hard Disk Drive HDD Capacity For more information regarding Hard Disk Drive HDD Capacity please refer to the Legal Footnotes section in Appendix C RTC battery The internal RTC battery backs up the Real Time Clock RTC and calendar Video RAM The memory in a computer s graphics adaptor used to store the image displayed on a bitmap display The amount of Video RAM available is dependent on the computer s system memory Start gt Control Panel gt Appearance and Personalization gt Display gt Adjust resolution The amount of Video RAM can be verified by clicking the Advanced settings button in the Screen Resolution window Display controller The display controller interprets software commands into hardware commands that turn particular parts on the screen on or off The display controller also controls the video mode and uses industry standard rules to govern the screen resolution and the maximum number of colors that can be displayed at a time Therefore software written for a given video mode will run on any computer that supports that mode Due to the display panel s increased resolution lines may appear broken in when displaying images in full screen text mode
59. aking a bath Injured finger Wet finger Soiled or oily finger BR Extremely dry skin condition on finger Observe the following to improve the fingerprint recognition success rate 3 9 Enroll two or more fingers Enroll additional fingers if a recognition failure often occurs when using already enrolled fingers Check the condition of your finger any conditions which have changed since enrollment such as injury rough skin and extremely dry wet soiled dirty oily soaked or swollen fingers may lower the recognition success rate Also if the fingerprint is worn down or the finger becomes thinner or fatter the recognition success rate may be lowered As the fingerprint for each finger is different and unique you should ensure that only the registered or enrolled fingerprint or fingerprints are used for identification Check the position and speed at which you swipe your finger across the sensor please refer to the preceding drawing The fingerprint sensor compares and analyzes the unique characteristics in a fingerprint However there may be instances where certain users are unable to register their fingerprints due to insufficient unique characteristics in their fingerprints The recognition success rate may differ from user to user Points to note about Fingerprint Utility If Windows 7 file encryption function EFS Encryption File System is used to encrypt a file the file cannot be further encrypted using the encry
60. al metallic water pipe systems if present are connected together This precaution may be particularly important in rural areas Users should not attempt to make such connections themselves but should contact the appropriate electric inspection authority or electrician as appropriate User s Manual xi T 2 The user manual of analog equipment must contain the equipment s Ringer Equivalence Number REN and an explanation notice similar to the following The Ringer Equivalence Number REN of the modem which can vary For the REN of your modem refer to your modem s label The Ringer Equivalence Number REN assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5 3 The standard connecting arrangement telephone jack type for this equipment is jack type s USOC RJ11C The IC registration number of the modem is shown below Canada 4005B DELPHI Notes for Users in Australia and New Zealand User s Manual Modem warning notice for Australia Modems connected to the Australian telecoms network must have a valid Austel permit This modem has been designed to specifically configure to ensure compliance with Austel standards when the country region sele
61. and data discs which can store copies of the files and folders on your computer s hard disk drive This software can be used on models with an optical disc drive To start this utility click Start gt All Programs gt TOSHIBA gt Media amp Entertainment gt Disc Creator User s Manual TOSHIBA DVD RAM Utility TOSHIBA HDD SSD Alert Utility TOSHIBA Service Station TOSHIBA Sleep Utility TOSHIBA Bulletin Board This utility has the function of Physical Format and Write Protect to DVD RAM This utility is contained the setup module of TOSHIBA Disc Creator To start this utility click Start gt All Programs gt TOSHIBA gt Media amp Entertainment gt DVD RAM Utility This utility includes wizard functions to monitor the Disk Drive operating status and execute the system backup To access the utility click Start gt All Programs gt TOSHIBA gt Support amp Recovery gt HDD SSD Alert This application allows your computer to automatically search for TOSHIBA software updates or other alerts from TOSHIBA that are specific to your computer system and its programs When enabled this application periodically transmits to our servers a limited amount of system information which will be treated in strict accordance with the rules and regulations as well as applicable data protection law To access this utility click Start gt All Programs gt TOSHIBA gt Support amp Recovery gt Serv
62. and reconnect the power first This equipment may not be compatible with Telecom Distinctive Alert cadences and services such as FaxAbility NOTE THAT FAULT CALLOUTS CAUSED BY ANY OF THE ABOVE CAUSES MAY INCUR A CHARGE FROM TELECOM xiv Following information is only valid for EU member States Disposal of products User s Manual The crossed out wheeled dust bin symbol indicates that products must be collected and disposed of separately from household waste Integrated batteries and accumulators can be disposed of with the product They will be separated at the recycling centres The black bar indicates that the product was placed on the market after August 13 2005 By participating in separate collection of products and batteries you will help to assure the proper disposal of products and batteries and thus help to prevent potential negative consequences for the environment and human health For more detailed information about the collection and recycling programmes available in your country please visit our website http eu computers toshiba europe com or contact your local city office or the shop where you purchased the product Disposal of batteries and or accumulators Pb Hg Cd The crossed out wheeled dust bin symbol indicates that batteries and or accumulators must be collected and disposed of separately from household waste If the battery or accumulator contains more than the specified values of lead Pb
63. anual 4 24 i If you use the computer for a long period the inside of the computer may become hot Always allow the computer to cool to room temperature before you clean the cooling module To clean the cooling module follow the steps detailed below 1 Shut down the computer make sure the Power indicator is off refer to the Turning off the power section in chapter 1 Getting Started if required 2 Remove the AC adaptor and all cables and peripherals connected to the computer 3 Close the display panel and turn the computer upside down 4 Remove the battery pack refer to the Replacing the battery pack section in chapter 5 Power and Power Up Modes if required 5 Using a thin tipped tool push on the hole in the edge of the Cooling module cover and slide it in the direction of the arrow to remove Figure 4 1 Removing the cooling module cover 1 Hole 2 Cooling module cover 6 Lt the plastic film and clean the cooling module using a vacuum cleaner or other cleaning tool ai Do not use a ball pen cotton swap or similar to remove dust If these touch d the inside of the computer it could be damaged or become clogged leading to further problems Figure 4 2 Lift the plastic film 1 Plastic film 7 Slide the Cooling module cover back into place on the computer to reattach User s Manual 4 25 8 Install the battery pack refer to the Replacing the battery pack section in chapter 5 Power and Power Up Modes
64. aptor cord will be included with the computer d depending on the model 2 Connect the AC adaptor s DC output plug to the DC IN 15V jack on the back of the computer Figure 1 3 Connecting the DC output plug to the computer 1 DC IN 15V jack 2 DC output plug 3 Plug the power cord into a live wall outlet the Battery and DC IN indicators on the front of the computer should glow Opening the display The display panel can be opened to a wide range of angles for optimal viewing While holding down the palm rest with one hand so that the main body of the computer is not raised slowly lift the display panel this will allow the angle of the display panel to be adjusted to provide optimum clarity User s Manual 1 4 Figure 1 4 Opening the display panel 1 Display panel Use reasonable care when opening and closing the display panel Opening it vigorously or slamming it shut could damage the computer Be careful not to open the display panel too far as this could put stress on the display panel s hinges and cause damage Do not press or push on the display panel Do not lift the computer by the display panel E Do not close the display panel with pens or any other objects left in between the display panel and the keyboard m When opening or closing the display panel place one hand on the palm rest to hold the computer in place and use the other hand to slowly open or close the display panel Do not use excessive for
65. arge function Auto Mode Default is suitable for a wide range of digital audio players Your computer supports high current mode 2 0A Mode Using the following procedure to find a suitable mode from Auto Mode to 2 0A Mode for your USB device to charge Do not use 2 0A Mode when your USB devices do not support high current mode 2 0A Mode This function may not be able to be used with some connected external devices even if the appropriate mode is selected In this situation clear the Enable Sleep and Charge check box and stop using this function While using 2 0A Mode your computer can supply USB bus power DC5V 2 0A to the compatible ports while the computer is turned off Some external devices cannot use high current mode 2 0A Mode As for the specifications of the external devices please contact the device s manufacture or check the specifications of the external device thoroughly before use It is recommended that AC adaptor be connected to the computer while using 2 0A Mode Never use USB devices and cables not supporting this feature when 2 0A Mode is used Always use the USB cable that was included with your USB device Battery Settings This utility can be used to specify the lower limit of remaining battery life for Sleep and Charge Move the slider bar to specify the lower limit If the User s Manual 4 11 remaining battery life falls below the setting the Sleep and Charge function will be stopped
66. art the computer as though it were a hard disk drive based on the hard disk drive settings within both the Boot Priority and HDD Priority options detailed previously FDD Sets the USB memory to be the equivalent of a floppy diskette drive With this setting the USB memory device can be used to start the computer as though it were a floppy diskette based on the floppy diskette drive settings within the Boot Priority option detailed previously Panel Open Power On This feature allows you to change the Panel Open Power On setting Enabled Enables the Panel Open Power On function When you open the display panel while your computer is turned off the system will boot up automatically Disabled Disables the Panel Open Power On function Default Keyboard Wake up on Keyboard When this feature is enabled and the computer is in Sleep Mode you can turn on the system by pressing any key However please be aware that 4 20 T User s Manual this option will only work with the internal keyboard and only when the computer is in Sleep Mode Enabled Enables the Wake up on Keyboard function Disabled Disables the Wake up on Keyboard function Default LAN Wake up on LAN This feature lets the computer s power be turned on from shutdown when it receives a wake up packet Magic packet from the LAN Do not install or remove a memory module while Wake up on LAN is enabled BR 7he Wake up on LAN function consumes pow
67. atible with the application at the other end of the call e g accessing the Internet requires suitable software in addition to a modem This equipment shall not be used in any manner which could constitute a nuisance to other Telecom customers Some parameters required for compliance with Telecom s PTC Specifications are dependent on the equipment PC associated with this modem The associated equipment shall be set to operate within the following limits for compliance with Telecom Specifications 1 There shall be no more than 10 call attempts to the same number within any 30 minute period for any single manual call initiation and 2 The equipment shall go on hook for a period of not less than 30 seconds between the end of one attempt and the beginning of the next 3 Automatic calls to different numbers shall be not less than 5 seconds apart Immediately disconnect this equipment should it become physically damaged and arrange for its disposal or repair The correct settings for use with this modem in New Zealand are as follows ATBO CCITT operation AT amp G2 1800 Hz guard tone AT amp P1 Decadic dialing make break ratio 33 67 ATSO 0 not auto answer ATS6 4 Blind dial delay ATS7 less than 90 Time to wait to carrier after dialing ATS10 less than 150 loss of carrier to hangup delay factory default of 15 recommended ATS11 90 DTMF dialing on off duration 90 ms ATX2 Dial tone detect but not U S A call p
68. ation of the User Password and if applicable the HDD Hard Disk Drive Password when booting up the computer Pre Boot Authentication E Single Sign On feature Fingerprint cannot be used in models that do not have a fingerprint module installed How to Swipe your Finger User s Manual Using the following steps when swiping fingers for fingerprint registration or authentication will help to minimize authentication failures Align the first joint of the finger to the center of the sensor Lightly touch the sensor and swipe finger levelly towards you until the sensor surface becomes visible In performing this process you should also take care to ensure that the center of your fingerprint is on the sensor The following illustrations show the recommended way to swipe your finger over the fingerprint sensor Figure 3 5 Swipe the finger 1 Sensor Avoid swiping with your finger stiff or pressed too hard onto the sensor and take care to ensure that the center of the fingerprint is touching the sensor before swiping Either of these conditions may cause fingerprint reading to fail Check the center of the fingerprint whorl before swiping and then ensure this is swiped along the center line of the sensor There is a possibility of authentication failures if the finger is swiped too quickly or too slowly follow any on screen instructions to adjust the speed used during the swipe process Points to note about the Fingerprint Sens
69. ay resolution ODD Pressing FN TAB ejects the disc tray E Reduce Pressing FN 1 reduces the icon size on the desktop or the font sizes within one of the supported application windows E Enlarge Pressing FN 2 enlarges the icon size on the desktop or the font sizes within one of the supported application windows FN Sticky key You can use the TOSHIBA Accessibility Utility to make the FN key sticky that is you can press it once release it and then press an F Number key To start the TOSHIBA Accessibility utility click Start gt All Programs gt TOSHIBA gt Tools amp Utilities gt Accessibility Windows special keys The keyboard provides two keys that have special functions in Windows the Windows Start Button key activates the Start menu while the application key has the same function as the secondary right mouse button A S This key activates the Windows Start menu S This key has the same function as the secondary right mouse button Keypad overlay for A4 size keyboard Your computer s keyboard may not have a separate numeric keypad but includes a numeric keypad overlay which functions like one this is located in the center of the keyboard with the relevant keys having grey letters at their front edge The overlay provides the same function as the numeric keypad on a standard 104 105 key enhanced keyboard Turning on the overlays The numeric keypad overlay can be used for numeric data inp
70. back of DVD Video and DVD VR E Frame dropping audio skipping or out of sync audio and video may occur during playback of some DVD Video titles BR Close all other applications when using the TOSHIBA VIDEO PLAYER Do not open any other applications or carry out any other operations during video playback Playback may stop or not function properly in some situations m Unfinalized DVDs created on home DVD recorders may not be playable on the computer m Use DVD Video discs with a region code which is either the same as the factory default setting if applicable or ALL BR Do not playback video while watching or recording television programs using other applications Doing so may cause DVD Video playback or television program recording errors In addition if prescheduled recording starts during DVD Video playback it may cause DVD Video playback or television program recording errors Please view DVD Video during times when there is no recording prescheduled BR The resume function cannot be used with some discs on the TOSHIBA VIDEO PLAYER E Itis recommended the AC adaptor be connected when playing video Power saving features may interfere with smooth playback When playing DVD Video using battery power set the Power Options to Balance BH The screen saver is disabled during video playback using the TOSHIBA VIDEO PLAYER The computer will not automatically go into Hibernation Sleep or shut down mode BR Do not configure the Di
71. be aware that your selected model may not have all the features and specifications corresponding to all of the icons or switches shown on the computer chassis Central Processing Unit CPU Performance Legal Footnotes CPU performance in your computer product may vary from specifications under the following conditions Huse of certain external peripheral products muse of battery power instead of AC power muse of certain multimedia computer generated graphics or video applications muse of standard telephone lines or low speed network connections use of complex modeling software such as high end computer aided design applications Huse of several applications or functionalities simultaneously BR use of computer in areas with low air pressure high altitude gt 1 000 meters or gt 3 280 feet above sea level muse of computer at temperatures outside the range of 5 C to 30 C 41 F to 86 F or gt 25 C 77 F at high altitude all temperature references are approximate and may vary depending on the specific computer model please refer to your computer documentation or visit the TOSHIBA website at www pcsupport toshiba com for details CPU performance may also vary from specifications due to design configuration Under some conditions your computer product may automatically shut down This is a normal protective feature designed to reduce the risk of lost data or damage to the product when used outside recommended conditions
72. bernation Mode feature provides the following benefits DH Saves data to the hard disk drive when the computer automatically shuts down because of a low battery condition BR You can return to your previous working environment immediately when you turn on the computer BR Saves power by shutting down the system when the computer receives no input or hardware access for the time period set by the System Hibernate feature E Allows the use of the panel power off feature Starting Hibernation Mode You can also enable Hibernation Mode by pressing FN F4 please refer to the Hot key functions section in Chapter 3 Operating Basics for further details To enter Hibernation Mode follow the steps below 1 Click Start 2 Point to the arrow icon ESZA and then select Hibernate from the menu Automatic Hibernation Mode The computer can be configured to enter Hibernation Mode automatically when you press the power button or close the lid In order to define these settings you can follow the steps as described below 1 Click Start and click the Control Panel 2 Click System and Security and click Power Options 3 Click Choose what the power button does or Choose what closing the lid does 4 Enable the desired Hibernation Mode settings for When I press the power button and When I close the lid 5 Click the Save changes button Data save in Hibernation Mode When you turn off the power in Hibernation Mode the computer
73. bit If the DVD Video image is not displayed on an external display or television stop the TOSHIBA VIDEO PLAYER and change the screen resolution To change the screen resolution click Start gt Control Panel gt Appearance and Personalization gt Display gt Adjust resolution However video cannot be output to some external displays and televisions due to output or playback conditions When viewing DVD Video on an external display or TV change the display device before playing DVD Video can be played only on internal LCD displays or external displays In Clone mode Dual View TOSHIBA VIDEO PLAYER may not function properly Do not change the screen resolution while running the TOSHIBA VIDEO PLAYER Do not change the display device while running the TOSHIBA VIDEO PLAYER Starting TOSHIBA VIDEO PLAYER Use the following procedure to start TOSHIBA VIDEO PLAYER 1 User s Manual Insert an DVD Video in the optical disc drive while Windows 7 is running 3 23 When a DVD Video disc is set in the DVD drive for models with DVD drive TOSHIBA VIDEO PLAYER may start automatically 2 Select Start gt All Programs gt TOSHIBA gt Media amp Entertainment gt TOSHIBA VIDEO PLAYER to start TOSHIBA VIDEO PLAYER Operating TOSHIBA VIDEO PLAYER Notes on Using TOSHIBA VIDEO PLAYER BH Screen display and available features may vary amongst DVD Videos and scenes mg Ifthe menu is opened in the Display Area using t
74. by Wireless products however is far much less than the electromagnetic energy emitted by wireless devices like for example mobile phones Because Wireless products operate within the guidelines found in radio frequency safety standards and recommendations TOSHIBA believes Wireless products is safe for use by consumers These standards and recommendations reflect the consensus of the scientific community and result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature In some situations or environments the use of Wireless products may be restricted by the proprietor of the building or responsible representatives of the organization These situations may for example include BR Using the Wireless products equipment on board of airplanes or E In any other environment where the risk of interference to other devices or services is perceived or identified as harmful If you are uncertain of the policy that applies on the use of wireless devices in a specific organization or environment e g airports you are encouraged to ask for authorization to use the Wireless device prior to turning on the equipment Radio Regulatory Information The Wireless device is must be installed and used in strict accordance with the manufacturer s instructions as described in the user documentation that comes with the product This product complies with the following radio frequency and
75. ce when opening or closing the display panel Turning on the power T User s Manual This section describes how to turn on the power the Power indicator will then indicate the status Please refer to the Monitoring of power condition section in Chapter 5 Power and Power Up Modes for more information BR After you turn on the power for the first time do not turn it off until you have set up the operating system E Volume cannot be adjusted during Windows Setup 1 Open the display panel 2 Press and hold the computer s power button for two or three seconds Figure 1 5 Turning on the power SE Pa 1 Power button Product appearance depends on the model you purchased Starting up for the first time T The Windows 7 Startup Screen will be the first screen displayed when you turn on the power Follow the on screen instructions on each screen in order to properly install the operating system When it is displayed be sure to read the Software License Terms carefully Turning off the power User s Manual The power can be turned off in one of three modes either Shut Down Mode Hibernation Mode or Sleep Mode Shut Down Mode When you turn off the power in Shut Down Mode no data will be saved and the computer will boot to the operating system s main screen the next time it is turned on 1 If you have entered data either save it to the hard disk drive or to other storage media 2 Make
76. ck and easy You cannot use the computer s built in Bluetooth functions and an external Bluetooth adaptor simultaneously For reference Bluetooth wireless technology has the following features 3 29 User s Manual Worldwide operation The Bluetooth radio transmitter and receiver operate in the 2 4GHz band which is license free and compatible with radio systems in most countries in the world Radio links You can easily establish links between two or more devices with these links being maintained even if the devices are not within a line of sight of each other Security Two advanced security mechanisms ensure a high level of security BR Authentication prevents access to critical data and makes it impossible to falsify the origin of a message BR Encryption prevents eavesdropping and maintains link privacy Bluetooth Stack for Windows by TOSHIBA Please note that this software is specifically designed for the following operating systems m Windows 7 Information regarding the use of this software with these operating systems is listed below with further details being contained with the electronic help files supplied with the software This Bluetooth Stack is based on the Bluetooth specification depending on the model you purchased However TOSHIBA cannot confirm the compatibility between any computing products and or other electronic devices that use Bluetooth other than TOSHIBA notebook computers Release Notes
77. cludes information on charging and changing batteries tips for saving battery power and information on the different power up modes Power conditions The computer s operating capability and battery charge status are affected by different power conditions including whether an AC adaptor is connected whether a battery pack is installed and what the charge level is for that battery AC adaptor connected Battery fully charged Battery partially charged or no charge No battery installed Power on e Operates e No charge e LED Battery green DC IN green e Operates e Charge e LED Battery orange DC IN green e Operates e No charge e LED Battery off DC IN green Power off no operation e No charge e LED Battery green DC IN green e Quick charge e LED Battery orange DC IN green e No charge e LED Battery off DC IN green AC adaptor not connected Remaining battery capacity is above low battery trigger point Remaining battery capacity is below low battery trigger point Remaining battery capacity is exhausted No battery installed Power on Power off no operation Operates e LED Battery off DC IN off e Operates e LED Battery flashes orange DC IN off Computer shuts down e No operation e LED Battery off DC IN off Monitoring of power condition As shown in the below table the Battery DC IN and Power indicators on the system indicator panel al
78. code do not match Displays a warning if the current settings for both region code and telephony location are different 3 25 Modem Selection If the computer cannot recognize the internal modem a dialog box is displayed from which you should select the appropriate communications port for your modem to use Dialing Properties You should select this item in order to display the dialing properties If you are using the computer in Japan the Telecommunications Business Law requires that you select Japan region mode It is illegal to use the modem in Japan with any other selection Connecting the modular cable To connect the modem s modular cable follow the steps as detailed below A BR Connection to any communication line other than an analog phone line could cause a computer system failure BR Connect the built in modem only to ordinary analog phone lines m Never connect the built in modem to a digital line ISDN m Never connect the built in modem to the digital connector on a public telephone or to a digital private branch exchange PBX m Never connect the built in modem to a key telephone system for residences or offices RB Avoid using your computer modem with the telephone cable connected during an electrical storm There may be a remote risk of electric shock from lightning Plug the end of the modular cable into the computer s modem jack 2 Plug the other end of the modular cable into a telephone jack Figur
79. cord adaptor is firmly connected to the DC IN indicator computer and a working power outlet does not glow green Check the condition of the cord and terminals If the cord is frayed or damaged it should be replaced while if the terminals are soiled they should be cleaned with a clean cotton cloth If the AC adaptor still does not power the computer you should contact TOSHIBA Support Battery If you suspect a problem with the battery you should check the status of the DC IN indicator as well as the Battery indicator Problem Procedure Battery doesn t The battery may be discharged connect the AC power the computer adaptor to recharge the battery Problem Procedure Battery doesn t If the battery is completely discharged it will not charge when the AC begin charging immediately in these instances you adaptor is attached should wait a few minutes before trying again If Battery indicator the battery still does not charge you should check does not glow that the power outlet the AC adaptor is connected orange to is supplying power this can be tested by plugging another appliance into it Check whether the battery is hot or cold to the touch if so it will not charge properly and should be allowed to reach room temperature before you try again Unplug the AC adaptor and remove the battery to make sure its connecting terminals are clean if necessary wipe them with a soft dry cloth lightly dipped in alcohol
80. ction is set to Australia The use of other country region setting while the modem is attached to the Australian PSTN would result in you modem being operated in a non compliant manner To verify that the country region is correctly set enter the command ATI which displays the currently active setting To set the country region permanently to Australia enter the following command sequence AT TE 1 ATS133 1 AT amp F AT amp W AT TE 0 ATZ Failure to set the modem to the Australia country region setting as shown above will result in the modem being operated in a non compliant manner Consequently there would be no permit in force for this equipment and the Telecoms Act 1991 prescribes a penalty of 12 000 for the connection of non permitted equipment xii Notes for use of this device in New Zealand User s Manual The grant of a Telepermit for a device in no way indicates Telecom acceptance of responsibility for the correct operation of that device under all operating conditions In particular the higher speeds at which this modem is capable of operating depend on a specific network implementation which is only one of many ways of delivering high quality voice telephony to customers Failure to operate should not be reported as a fault to Telecom In addition to satisfactory line conditions a modem can only work properly if 1 it is compatible with the modem at the other end of the call and 2 the application using the modem is comp
81. d into their uppercase format NUM LOCK When the NUM LOCK indicator glows you can use the number keys on the keyboard for number entry Function keys F1 F12 The function keys not to be confused with the special FN key are the twelve keys at the top of your keyboard these keys function differently from other keys F a P a P P S IF E Fe E JE H J amp User s Manual 3 3 F1 through F12 are called function keys because they execute programmed functions when pressed and when used in combination with the FN key those keys marked with icons also execute specific functions on the computer Soft keys FN key combinations T The FN function is used in combination with other keys to form soft keys Soft keys are key combinations that enable disable or configure specific features Please note that some software may disable or interfere with soft key operations and that the soft key settings are not restored when the computer returns from Sleep Mode This computer s keyboard is designed to provide all the features of the 104 key enhanced keyboard Since the keyboard is smaller and has fewer keys some of the enhanced keyboard functions must be simulated using two keys instead of one on the larger keyboard The FN key can be combined with the following keys to simulate functions similar to those of keys on the 104 105 key enhanced keyboa
82. d this computer in accordance with applicable laws and regulations For further information contact your local government m This computer contains rechargeable batteries After repeated use the batteries will finally lose their ability to hold a charge and you will need to replace them Under certain applicable laws and regulation it may be illegal to dispose of old batteries by placing them in the trash m Please be kind to our shared environment Check with your local government authority for details regarding where to recycle old batteries or how to dispose of them properly REACH Compliance Statement User s Manual The new European Union EU chemical regulation REACH Registration Evaluation Authorization and Restriction of Chemicals entered into force on 1 June 2007 TOSHIBA will meet all REACH requirements and is committed to provide our customers with information about the chemical substances in our products according to REACH regulation Please consult the following website www toshiba europe com computers info reach for information about the presence in our articles of substances included on the candidate list according to article 59 1 of Regulation EC No 1907 2006 REACH in a concentration above 0 1 weight by weight xvi Following information is only for Turkey Compliant with EEE Regulations TOSHIBA meets all requirements of Turkish regulation 26891 Restriction of the use of certain hazardous
83. de If you have to interrupt your work you can use this feature to allow you to turn off power to the computer without exiting from your software Data is maintained in the computer s main memory so that when you next turn on the power you can continue working right where you left off USB Wakeup function This function restores the computer from Sleep Mode depending on the external devices connected to the USB ports For example if a mouse or USB keyboard is connected to a USB port clicking the mouse button or pressing the keyboard will wakeup the computer TOSHIBA PC Health The TOSHIBA PC Health Monitor application Monitor proactively monitors a number of system functions such as power consumption battery health and system cooling informing you of significant system conditions This application recognizes the system and individual component serial numbers and will track specific activities related to their usage Using the TOSHIBA Sleep Utility This utility displays whether the Sleep and Charge function is enabled or disabled and shows the positions of USB ports that support the Sleep and Charge function It also displays the remaining battery capacity User s Manual 4 9 Sleep and Charge User s Manual Your computer can supply USB bus power DC5V to the USB port even when the power of the computer is turned OFF Power OFF includes Sleep Mode Hibernation Mode or shutdown state This function can be used for ports t
84. dicator glows the keypad overlay allows you to use cursor functions m When the Numeric Mode indicator glows the keypad overlay allows you to enter numbers Figure 3 2 CAPS LOCK indicator 1 CAPS LOCK indicator CAPS LOCK This indicator glows green when letter keys are locked into their uppercase format Figure 3 3 Keypad overlay indicators F8 P el F10 7 F11 e F12 a PRISE D a amp EEE EE i P P P J 1 Arrow mode indicator 2 Numeric mode indicator User s Manual 3 2 Arrow mode When the Arrow mode indicator lights green e gt you can use the gray labeled keys on the keypad overlay as cursor keys Please refer to the Keypad overlay for A4 size keyboard section for more information Numeric mode When the Numeric mode indicator lights green you can use the gray labeled keys on the keypad overlay for number entry Please refer to the Keypad overlay for A4 size keyboard section for more information Full size keyboard The following figures show the positions of the CAPS LOCK indicator and the NUM LOCK indicators which show the following conditions m When the CAPS LOCK indicator glows the keyboard will produce capitals when any letter is typed m When the NUM LOCK indicator glows the ten key allows you to enter numbers Figure 3 4 Keypad indicators 1 CAPS LOCK indicator 2 NUM LOCK indicator CAPS LOCK This indicator glows green when letter keys are locke
85. e Try adjusting the contrast and brightness controls on the external monitor Press the FN F5 hot key in order to change the display priority and ensure that it is not set for the internal display only Check to see if the external monitor is connected When the external monitor is set as the primary display device in extended desktop mode it will not display when the computer wakes up from Sleep Mode if the external monitor has been disconnected while in Sleep Mode To keep this from happening do not disconnect the external monitor while the computer is in Sleep or Hibernation Mode Remember to turn off the computer before disconnecting the external monitor When the display panel and an external monitor are set to clone mode and they are turned off by the timer the display panel or the external monitor may not display when turned on again If this occurs press FN F5 to re set the display panel and external monitor to clone mode Check that the cable connecting the external monitor to the computer is firmly attached If you are still unable to resolve the problem contact TOSHIBA Support This information is applicable to the models equipped with a built in modem Problem Communication software can t initialize modem You can hear a dial tone but can t make a call Procedure Make sure the computer s internal modem settings are correct please refer to the Phone and Modem Options link within the
86. e 3 9 Connecting the internal modem 1 Modem jack 3 Telephone jack 2 Modular cable Do not pull on the cable or move the computer while the cable is connected User s Manual 3 26 7 If you use a storage device such as an optical disc drive or hard disk drive d connected to a 16 bit PC Card you might experience the following problems with the operation of the modem E The modem speed is slow or communication is periodically interrupted E Skips or jumps may be noted in sound Disconnecting the modular cable To disconnect the modular cable follow the steps as detailed below 1 Pinch the lever on the plug in the telephone jack and pull it out from within the connector 2 Pinch the lever on the plug in the computer s modem jack and pull it out from within the computer Wireless communications The computer s wireless communication function supports some wireless communication devices Only some models are equipped with both Wireless LAN and Bluetooth functions A m Do not use the Wireless LAN Wi Fi or Bluetooth functionalities near a microwave oven or in areas subject to radio interference or magnetic fields Interference from a microwave oven or other source can disrupt Wi Fi or Bluetooth operation BR Turn all wireless functionalities off when near a person who may have a cardiac pacemaker implant or other medical electric device Radio waves may affect pacemaker or medical device operation possibly resulting i
87. e Boot Authentication and Single Sign on feature becomes effective the next time the system is booted up Optical disc drives The computer may be installed with an Optical Disc Drive When the computer is accessing an optical disc an indicator on the drive glows Some models are equipped with an optical disc drive Formats T User s Manual The drives support the following formats DVD Super Multi drive Double Layer The drive supports the following formats CD ROM DVD ROM DVD Video CD DA CD Text Photo CD single multi session CD ROM Mode 1 Mode 2 CD ROM XA Mode 2 Form1 Form2 Enhanced CD CD EXTRA Addressing Method 2 DVD R DVD RW DVD R DVD RW DVD RAM DVD R DL Format1 DVD R DL Some types and formats of DVD R DL and DVD R DL discs may be unreadable Using optical disc drives T User s Manual The full size drive provides high performance execution of disc based programs You can run either 12 cm 4 72 or 8 cm 3 15 discs without an adaptor Use the DVD playback application to view DVD Video discs If you have an Optical disc drive refer also to the Writing discs section for precautions on writing to discs To load discs follow the steps as detailed below 1 When the computer s power is on press the eject button to open the disc tray slightly 2 Grasp the disc tray gently and pull until it is fully opened Figure 3 6 Pressing the eject button and pulling the disc tray open
88. e battery lock to release the battery pack ready for removal 2 Battery release latch Slide and hold this latch into its Unlock position D User s Manual Battery pack in order to release the battery pack for removal For more detailed information on removing the battery pack please refer to Chapter 5 Power and Power Up Modes The rechargeable lithium ion battery pack provides power to the computer when the AC adaptor is not connected For more detailed information on the use and operation of the battery pack please refer to Chapter 5 Power and Power Up Modes Legal Footnote Battery Life For more information regarding Battery Life please refer to the Legal Footnotes section in Appendix C Memory module slot The memory module slot allows the installation replacement and removal of additional memory module The size of the memory modules varies depending on the model The actual amount of useable system memory may be less than the installed memory modules Refer to the Additional memory module section in Chapter 3 Operating Basics Legal Footnote Memory Main System For more information regarding Memory Main System please refer to the Legal Footnotes section in Appendix C Front with the display open This section shows the computer with the display panel open In order to open the display lift the display panel up and position it at a comfortable viewing angle for you Figure 2 6 The front of
89. e computer s default settings could cause a malfunction in LAN operation Check with your LAN administrator regarding set up procedures If you are using Gigabit Ethernet LAN 1000 megabits per second 1000BASE T be sure to connect with a CAT5e cable or higher You cannot use a CAT3 or CAT5 cable If you are using Fast Ethernet LAN 100 megabits per second 100BASE TX be sure to connect with a CAT5 cable or higher You cannot use a CAT3 cable If you are using Ethernet LAN 10 megabits per second 10BASE T you can connect with a CAT3 or higher cable Connecting the LAN cable A User s Manual To connect the LAN cable follow the steps as detailed below E Connect the AC adaptor before connecting the LAN cable The AC adaptor must remain connected during LAN use If you disconnect the AC Adaptor while the computer is accessing a LAN the system may hang up BR Do not connect any other cable to the LAN jack except the LAN cable Otherwise malfunctions or damage may occur 3 31 D Do not connect any power supplying device to the LAN cable that is connected to the LAN jack Otherwise malfunctions or damage may occur 1 Turn off the power to all external devices connected to the computer 2 Plug one end of the cable into the LAN jack Press gently until you hear the latch click into place Figure 3 10 Connecting the LAN cable 1 LAN jack 2 LAN cable 3 Plug the other end of the cable into a LAN hub connector or rou
90. e displayed Select Start face recognition H Please face the camera will be displayed Verification will be performed If the authentication is successful the image data taken in step 4 will be faded in and placed over one another IRN If an error occurs during authentication you will be returned to the Select Tiles screen 6 The Windows Welcome screen will be displayed and will be logged in automatically to Windows 1 1 Mode Login screen Turn on the computer The Select Tiles screen will be displayed Select Start face recognition H The Select Account screen will be displayed Select the account and click the arrow button Please face the camera will be displayed Verification will be performed If the authentication is successful the image data taken in step 6 will be faded in and placed over one another NOaRWN gt If an error occurs during authentication you will be returned to the Select Tiles screen 8 The Windows Welcome screen will be displayed and will be logged in automatically to Windows If authentication was successful but an authentication error subsequently occurred during the login to Windows you will be asked to provide your account information TOSHIBA Password Utility T The TOSHIBA Password Utility provides two levels of password security User and Supervisor Passwords set by the TOSHIBA Password Utility function are different from the Windows password User Passw
91. e ee eeeeeeeeeeeeeeeeeennseeeeeneeneneeees 3 39 Eeterpalteultgt tee eege eebe 3 43 Mini DisplayPort eSATA External Serial ATA device ccccccceeeeseeneeeseeneneseeeneseeees 3 45 Serial Port 0 eceeceseeceseeeeeeeeeeeeeeeeeeseeeeseseeeeseseeseseseesnsseeesaseeseeeseesnnsoneeeas 3 46 Security Iock ceeceeeeeeceeeeeneeeeeeeseeeeseeeeseseeeeeaseeseseeeesesaeeeseseeseseseesnnsneeenes 3 46 Optional TOSHIBA Accessories een 3 47 SOUNG System EE 3 47 Vide OU TEE 3 49 Computer Handling cceeceseeeeseeeeeeseeeeeesenseeeeeeseseeeeseseeseeeseesnnaneeenes 3 49 Heat dispersal vrisnes iaai andina daaa ee NE ENNEN 3 50 Utilities amp Advanced Usage Utilities and Applications 0 0 ceeeeecete esses ee eeeeeeesceneeeseesensneeeeeeeneeeeees 4 1 Special features ceecceseeeeeseeeseeeeeeseeeeeeeeeseseeeeseseneeeeseesensneesessoneeeees 4 7 Using the TOSHIBA Sleep Utility 20 0 ces seeeeeeseeeeeeeeeeneeeeeesenenneneeens 4 9 Using the TOSHIBA Face Recognition cccccseeeeeeeeseeeeeeeeeneneees 4 12 TOSHIBA Password Unit cececeseseeeeeseeeeseeeeseeeeeesseneeeseeneneneeees 4 15 HW Setup ocres naaien eeceeeeeeeeeeeeeesaasaeeeeseeeenseeeesasensesneeeeneeeeeessonenenees 4 18 TOSHIBA PC Health Monitor ccscceccecceseeceeeeeseneeseeeeeeenseeeeeeeeeenes 4 23 Using the Hard Disk Drive HDD Protection ccecsseeeeeseeeeeees 4 26 TOSHIBA HDD Protection Properties ccceseeeseeeeeeseneeeeeeeeseeeees 4 26 System RECO
92. e issues getting an image displayed on the correct monitor you should consider using the FN F5 hot key to change the display settings if you then disconnect the external monitor before you turn the computer s power off be sure to press FN F5 hot key again to switch to the internal display Please refer to the The Keyboard section for further details on using hot keys to change the display setting When displaying desktop at external analog monitor desktop is sometimes displayed on the center of the monitor with black bars around desktop with small size At that time please read the manual of the monitor and set the display mode which is supporting at the monitor Then it will be displayed with suitable size with correct aspect ratio Mini DisplayPort With a suitable adapter such as the Mini DisplayPort to HDMI adapter or Mini DisplayPort to DVI adapter this port enables you to connect an external monitor Connecting the Mini DisplayPort 1 Plug the Mini DisplayPort connector of the adapter into the Mini DisplayPort on your computer Figure 3 20 Connecting the Mini DisplayPort 1 Mini DisplayPort 2 Mini DisplayPort Connector User s Manual 3 44 2 a P Connect one end of the monitor cable to the HDMI or DVI port on your external monitor and connect the other end to the suitable port of the adapter Mini DisplayPort to HDMI adapter or Mini DisplayPort to DVI adapter is not supplied with your computer Thi
93. e memory media you may lose data or damage the media Do not remove the memory media while the computer is in Sleep or Hibernation Mode The computer could become unstable or data in the memory media could be lost Do not remove only the Memory Stick Duo Memory Stick PRO Duo Memory Stick Micro miniSD microSD Card while leaving the adaptor in the memory media slot User s Manual 3 38 Additional memory module You can install additional memory into the computer in order to increase the amount of system memory that is available This section describes how to install and remove optional memory modules T z You should place a mat beneath the computer in order to prevent the computer s lid from becoming scratched or damaged when you are installing replacing the memory module In this instance you should avoid mats that are made of materials that hold or generate static electricity When installing or removing a memory module you must ensure that you do not touch any other internal areas of the computer Insert the two memory modules into Slot A and Slot B respectively The computer will operate in dual channel mode You can access the inserted memory modules efficiently in dual channel Use only memory modules approved by TOSHIBA Do not try to install or remove a memory module under the following conditions a The computer is turned on b The computer was shut down in either Sleep or Hibernation Mode c Wake up on LAN is
94. e sure to connect the AC adaptor when you create Recovery Media Be sure to close all other software programs except the Recovery Media Creator Do not run software such as screen savers which can put a heavy load on the CPU Operate the computer at full power Do not use power saving features Do not write to the media when the virus check software is running Wait for it to finish then disable virus detection programs including any software that checks files automatically in the background Do not use utilities including those intended to enhance hard disk drive access speed They may cause unstable operation and damage data Do not shut down log off or Sleep Hibernate while writing or rewriting the media Set the computer on a level surface and avoid places subjected to vibrations such as airplanes trains or cars Do not use on an unstable surface such as a stand A recovery image of the software on your computer is stored on the hard disk drive and can be copied to either DVD or USB Flash Memory by using the following steps 1 Select either blank disc or USB Flash Memory The application will allow you to choose from a variety of different media onto which the recovery image can be copied including disc media and USB Flash Memory Please note that some of the above media may not be compatible with the optical disc drive You should therefore verify the optical disc drive supports the blank media you have chosen be
95. ear on the screen Click OK Click Close 8 Are you sure you want to quit is displayed Click OK It will be returned to the TOSHIBA Fingerprint Utility main menu akon D N Windows Logon via Fingerprint Authentication T User s Manual In place of the usual Windows logon by ID and password fingerprint authentication also allows logon to Windows This is useful especially when many users are using the PCs as user selection can be skipped Fingerprint Authentication Procedure 1 Start up the computer 2 The Logon Authorization screen is displayed Choose any of the enrolled fingers and swipe the fingerprint on the sensor If authentication is successful the user will be logged on to Windows m f the fingerprint authentication fails please logon using the Windows logon password E A warning message will be displayed when authentication is abnormal or authentication is not successful within a fixed duration Fingerprint Pre Boot Authentication and Single Sign on feature T User s Manual Overview about Fingerprint Pre Boot Authentication The fingerprint authentication system can be used to replace the keyboard based User Password authentication system when booting up If you do not want to use the fingerprint authentication system for password authentication when booting up but prefer to use the keyboard based system instead click the user s tile when the Fingerprint System Authentication screen is d
96. ecome very warm While the temperature will not feel hot to the touch if you maintain physical contact with the computer for a long time for example if you rest the computer on your lap or if you keep your hands on the palm rest your skin might suffer a low heat injury E Ifthe computer has been used for a long time avoid direct contact with the metal plate supporting the various interface ports as this can become hot m The surface of the AC adaptor can become hot when in use but this condition does not indicate a malfunction If you need to transport the AC adaptor you should disconnect it and let it cool before moving it BR Do not lay the AC adaptor on a material that is sensitive to heat as the material could become damaged Pressure or impact damage Do not apply heavy pressure to the computer or subject it to any form of strong impact as this can damage the computer s components or otherwise cause it to malfunction PC Card ExpressCard overheating Some PC Cards ExpressCards can become hot during prolonged use which may result in errors or instability in the operation of the device in question In addition you should also be careful when you remove a PC Card ExpressCard that has been used for a long time Mobile phones Please be aware that the use of mobile phones can interfere with the audio system The operation of the computer will not be impaired in any way but it is recommended that a minimum distance of 30cm is main
97. elTime TOSHIBA HWSetup Utility TOSHIBA Web Camera Application TOSHIBA Face Recognition TOSHIBA HDD Protection TOSHIBA Service Station TOSHIBA PC Health Monitor TOSHIBA Sleep Utility TOSHIBA Fingerprint Utility User s Manual this manual You may not have all the softwares listed above depending on the model you purchased Getting Started i T User s Manual All users should be sure to read the section Starting up for the first time Be sure to read the enclosed Instruction Manual for Safety and Comfort for information on the safe and proper use of this computer It is intended to help you be more comfortable and productive while using a notebook computer By following the recommendations in it you may reduce your chance of developing a painful or disabling injury to your hand arms shoulders or neck This section provides basic information to start using your computer It covers the following topics Connecting the AC adaptor Opening the display Turning on the power Starting up for the first time Turning off the power Restarting the computer Use a virus check program and make sure it is updated regularly Never format storage media without checking its content formatting destroys all stored data It is a good idea to periodically back up the internal hard disk drive or other main storage device to external media General storage media is not durable or stable over long periods of time and under certain conditio
98. elephone number of the sending machine or such business other entity or individual In order to program this information into your fax modem you should complete the setup of your fax software before sending messages AN Use only No 26AWG or larger modular cable Instructions for IC CS 03 certified equipment 1 The Industry Canada label identifies certified equipment This certification means that the equipment meets certain telecommunications network protective operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document s The Department does not guarantee the equipment will operate to the user s satisfaction Before installing this equipment users should ensure that it is permissible to be connected to the facilities of the local telecommunications company The equipment must also be installed using an acceptable method of connection The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations Repairs to certified equipment should be coordinated by a representative designated by the supplier Any repairs or alterations made by the user to this equipment or equipment malfunctions may give the telecommunications company cause to request the user to disconnect the equipment Users should ensure for their own protection that the electrical ground connections of the power utility telephone lines and intern
99. elete the Face Recognition Data follow the steps as described below 1 To launch this utility click Start gt All Programs gt TOSHIBA gt Tools amp Utilities gt Face Recognition The Management screen is displayed 2 Select a user which is displayed in the Management screen 3 Click the Delete button You are about to delete the user data Would you like to continue will be displayed on the screen BH wou do not want the data to be deleted click the No button and you will then be returned to the Management screen H Clicking on the Yes button will remove the selected user from the Management screen How to launch the help file For further information on this utility please refer to help file To launch the help file click on the Help button in the Management screen Windows Logon via TOSHIBA Face Recognition User s Manual This section explains how to login to Windows with TOSHIBA Face Recognition Two authentication modes are provided BH 1 N Mode Login screen If the face authentication tile is selected by default you can log in without using the keyboard or mouse BR 1 1 Mode Login screen This mode is essentially the same as AUTO mode but the Select Account screen will appear before the Display Captured Image screen and you will need to select the user account to be authenticated in order to start the authentication process N Mode Login screen Turn on the computer The Select Tiles screen will b
100. emoving a hot PC Card Inserting a PC Card The Windows hot install feature allows you to insert PC Cards while the computer is turned on 7 Do not insert a PC Card while the computer is in Sleep Mode or J Hibernation Mode as you may find that some cards do not work properly To insert a PC Card follow the steps as detailed below 1 Insert the PC Card into the PC Card slot on the left side of the computer 2 Press the PC Card gently to ensure a firm connection is made Figure 3 12 Inserting the PC Card 1 PC Card slot 2 PC Card 3 After inserting the PC Card you should refer to its documentation and also check the configuration in Windows in order to ensure that it is correct Removing a PC Card To remove a PC Card follow the steps as detailed below 1 Open the Safely Remove Hardware and Eject Media icon on the Windows Taskbar 2 Point to PC Card and click the left Touch Pad control button User s Manual 3 34 A 3 Press the PC Card eject button to partially extend it out of the computer If the PC Card is not inserted all the way into the computer the eject button may not cause it to pop out sufficiently to allows it to be grasped In this instance simply push the PC Card firmly back into the computer and then press the eject button again 4 Press the extended PC Card eject button in order to eject the PC Card partially out of the computer 5 Grasp the PC Card and remove it Memory media A User s Ma
101. enabled d The wireless communication function is on e Sleep and Charge function is enabled Be careful not to let screws or other foreign matter fall into the computer It could cause malfunction or electric shock Additional memory module is a precision electronic component that may be fatally damaged by static electricity Since the human body can carry static electricity it is important that you discharge yourself before touching or installing any additional memory modules To discharge your body s static electricity simply touch any metal close to you with bare hands 7 Use a point size 0 Phillips screwdriver to remove and fasten the screws d the use of an incorrect screwdriver can damage the screw heads Installing a memory module To install a memory module follow the steps as detailed below 1 User s Manual Shut down the computer make sure the Power indicator is off refer to the Turning off the power section in Chapter 1 Getting Started if required 3 39 2 Remove the AC adaptor and all cables and peripherals connected to the computer Close the display panel 4 Turn the computer upside down and remove the battery pack refer to Replacing the battery pack section in Chapter 5 Power and Power Up Modes if required 5 Loosen the screw s securing the memory module cover in place please note that the screw s are attached to the cover in order to prevent them from being lost 6 Slide your fing
102. eneral This window displays the BIOS EC version and contains two buttons Default and About Default Return all HW Setup values to the factory settings About Display the HW Setup version Setup This field displays the installed BIOS Version EC Version and date User s Manual Display This tab lets you customize your computer s display settings for either the internal display or an external monitor Power On Display This option allows you to select the display to be used when the computer is started Please note that this setting is only available on standard VGA mode and is not available as part of the Windows Desktop properties Auto Selected Selects an external monitor if one is connected and the display panel is closed otherwise it selects the internal display Default System LCD Only Selects the internal LCD even if an external monitor is connected CPU This function allows you to set the processor s operating mode Dynamic CPU Frequency Mode This option allows you to configure the power saving modes associated with the processor the following settings are available Dynamically The processor s automatic clock speed switching Switchable function is enabled in use the processor s operation is automatically switched when necessary default Always High The processor s automatic clock speed switching function is disabled in use the processor will always run at its highest level of power consu
103. eo mode 3 49 Video RAM 2 12 Web Camera 2 9 Wireless communication indicator 2 2 Wireless LAN problems 6 18 Index 4 Glossary User s Manual The terms in this glossary cover topics related to this manual Alternate naming is included for reference Abbreviations AC Alternating current ANSI American National Standards Institute AMT Intel Active Management Technology ASCII American Standard Code for Information Interchange BIOS basic input output system bps bits per second CD compact disc CD ROM Compact Disc Read Only Memory CD RW Compact Disc ReWritable CMOS complementary metal oxide semiconductor CPU central processing unit CRT cathode ray tube DC direct current DDR double data rate DIMM dual inline memory module DVD digital versatile disc DVD R Digital Versatile Disc Recordable DVD RAM Digital Versatile Disc Random Access Memory DVD R DL Digital Versatile Disc Recordable Dual Layer DVD ROM Digital Versatile Disc Read Only Memory DVD RW Digital Versatile Disc ReWritable DVD R DL Digital Versatile Disc Recordable Double Layer eSATA external Serial ATA FDD floppy diskette drive FIR fast infrared GB gigabyte HDD hard disk drive HDMI High Definition Multimedia Interface IDE integrated drive electronics IEEE Institute of Electrical and Electronics Engineers I O input output IRQ interrupt request Glossary 1 KB kilobyte LAN local area network LCD liquid cr
104. ep Mode within the Power Options to access it Start gt Control Panel gt System and Security gt Power Options BH Touse the Hybrid Sleep function configure it in the Power Options Benefits of Sleep Mode The Sleep Mode feature provides the following benefits Restores the previous working environment more rapidly than does the Hibernation Mode feature E Saves power by shutting down the system when the computer receives no input or hardware access for the time period set by the System Sleep Mode feature BR Allows the use of the panel power off feature Executing Sleep Mode k T You can also enable Sleep Mode by pressing FN F3 please refer to the d Hot key functions section in Chapter 3 Operating Basics for further details You can enter Sleep Mode in one of three ways BR Click Start point to the arrow icon Es and then select Sleep from the menu BH Close the display panel Please note that this feature must be enabled within the Power Options to access it click Start gt Control Panel gt System and Security gt Power Options m Press the power button Please note that this feature must be enabled within the Power Options to access it click Start gt Control Panel gt System and Security gt Power Options When you turn the power back on you can continue where you left when you shut down the computer 7 RB When the computer is in Sleep Mode the power indicator will blink I orange
105. er even when the system is off Leave the AC adaptor connected while using this feature E Regarding Wake up on LAN from sleep or hibernation you must check the Allow the device to wake the computer check box within the LAN Device properties This feature does not effect the Wake up on LAN from sleep or hibernation Power will be automatically turned on when a signal is received from an administrator s computer which is connected via a network The following settings can be changed when the Built in LAN is Enabled Connect the AC adaptor when using the Wake up on LAN function The battery retention time will be shorter than the times listed in this manual when this function is enabled Refer to the Batteries exhausted time section in chapter 5 Power and Power Up Modes Enabled Enables Wake up on LAN from sleep mode Disabled Disables Wake up on LAN from sleep mode Default Built in LAN This feature enables or disables the Built in LAN Enabled Enables Built in LAN functions Default Disabled Disables Built in LAN functions 4 21 User s Manual USB Legacy USB Support Use this option to enable or disable USB Legacy Emulation If your operating system does not support USB you can still use a USB mouse and keyboard by setting the Legacy USB Support item to enabled Enabled Enables the USB Legacy Emulation Default Disabled Disables the USB Legacy Emulation Internal USB 3 0 controller Use this option to enable
106. erica Information Systems Inc 9740 Irvine Boulevard Irvine California 92618 1697 Telephone 949 583 3000 EU Declaration of Conformity User s Manual This product is carrying the CE Mark in accordance with the related European Directives Responsible for CE Marking is TOSHIBA Europe GmbH Hammfelddamm 8 41460 Neuss Germany The complete and official EU Declaration of Conformity can be found on TOSHIBA s web site http epps toshiba teg com on the Internet CE compliance This product is labelled with the CE Mark in accordance with the related European Directives notably Electromagnetic Compatibility Directive 2004 108 EC for the notebook and the electronic accessories including the supplied power adapter the Radio Equipment and Telecommunications Terminal Equipment Directive 1999 5 EC in case of implemented telecommunication accessories and the Low Voltage Directive 2006 95 EC for the supplied power adapter Furthermore the product complies with the Ecodesign Directive 2009 125 EC ErP and its related implementing measures This product and the original options are designed to observe the related EMC Electromagnetic Compatibility and safety standards However TOSHIBA cannot guarantee that this product still observes these EMC standards if options or cables not produced by TOSHIBA are connected or implemented In this case the persons who have connected implemented those options cables have to provide assurance that the sy
107. ernail or a thin object under the cover and lift it off Figure 3 15 Removing the memory module cover Vo si 1 Screw 2 Memory module cover User s Manual 3 40 7 Align the notch of the memory module with that of the memory slot and gently insert the module into the slot at about a 30 degree angle before holding it down until the latches on either side snap into place Figure 3 16 Seating the memory module 1 Slot A 3 Notch 2 Slot B A m Never allow metal objects such as screws staples and paper clips to enter the computer Foreign metal objects can create a short circuit which can cause computer damage and fire possibly resulting in serious injury Do not touch the connectors on the memory module or on the computer Debris on the connectors may cause memory access problems 7 BR The slot A is reserved for the first memory module Use the slot B for J expanded memory If only one module is installed use the slot A E Align the grooves along the edges of the memory module with the locking tabs on the connector and insert the module into the connector firmly if you find it difficult to install the memory module gently prise the locking tabs outwards using the tip of your finger BH Please also ensure that you hold the memory module along its lef
108. ert you to the computer s operating capability and battery charge status Battery indicator Check the Battery indicator to determine the status of the battery pack The following indicator lights indicate the battery status Flashing orange Orange Green No light The battery charge is low the AC adaptor must be connected in order to recharge the battery Indicates the AC adaptor is connected and the battery is charging Indicates the AC adaptor is connected and the battery is fully charged Under any other conditions the indicator does not light User s Manual T If the battery pack becomes too hot while it is being charged the charge will stop and the Battery indicator will go out When the battery pack s temperature falls to a normal range charging will resume this process will occur regardless of whether the computer s power is on or off DC IN indicator Check the DC IN indicator to determine the power status with the AC adaptor connected the following indicator conditions should be noted Green Indicates the AC adaptor is connected and is correctly supplying power to the computer Flashing orange Indicates a problem with the power supply You should initially try plugging the AC adaptor into another power outlet if it still does not operate properly you should contact TOSHIBA Support No light Under any other conditions the indicator does not light Power indicator Battery Check the
109. ery Media into the ODD or insert the recovery USB Flash Memory into one available USB port 2 Turn off the computer s power 3 While holding down F12 key on the keyboard turn on your computer when the TOSHIBA Leading Innovation gt gt gt logo screen appears release the F12 key 4 Use the up and down cursor key to select the appropriate option from the menu according to your actual recovery media Please refer to the Boot Setting section for further information 5 Amenu will be displayed from which you should follow the on screen instructions When drivers utilities are installed you can setup the respective drivers utilities from the following place To open the setup files Click Start gt All Programs gt TOSHIBA gt Support amp Recovery gt Applications and Drivers If you have previously chosen to remove the recovery partition and are trying to create Recovery Media you will see the following message The Recovery Media Creator can not be launched because there is no recovery partition When there is no recovery partition the Recovery Media Creator cannot make Recovery Media However if you have already created a Recovery Media you can use it to restore the recovery partition If you have not created Recovery Media please contact TOSHIBA support for assistance 4 30 Restoring the pre installed software from the Recovery hard disk drive T A portion of the total hard disk drive space is c
110. etooth Special Interest Group BR Logo certification with Bluetooth wireless technology as defined by the Bluetooth Special interest Group Please note that it is not possible to confirm the operation of all functions of all Bluetooth devices that are available In view of this it may be noted that some functions associated with a specific device might not operate properly CAUTION about Wireless Devices A User s Manual The wireless devices have not completed verification of connection and operation with all devices which are using the Wireless LAN or Bluetooth radio technology Bluetooth and Wireless LAN devices operate within the same radio frequency range and may interfere with one another If you use Bluetooth and Wireless LAN devices simultaneously you may occasionally experience a less than optimal network performance or even lose your network connection If you should experience any such problem immediately turn off either one of your Bluetooth or Wireless LAN Please visit http Avww pc support global toshiba com if you have any questions about using Wireless LAN or Bluetooth Card from TOSHIBA In Europe visit http Avww toshiba europe com computers tnt bluetooth htm Your Bluetooth product is not compatible with devices using Bluetooth Version 1 0B specifications Wireless Devices and your health Wireless products like other radio devices emit radio frequency electromagnetic energy The level of energy emitted
111. fore moving the computer BH Close the display panel Do not pick up the computer by its display panel RH Before carrying your computer shut it down disconnect the AC adaptor and allow it to cool down a failure to follow this instruction may result in minor heat injury BH Be careful not to subject the computer to impact or shock a failure to follow this instruction could result in damage to computer computer failure or loss of data Never transport your computer with any cards installed this may cause damage to either the computer and or the card resulting in product failure BR Always use a suitable carry case when transporting the computer m When carrying your computer be sure to hold it securely so that it does not fall or hit anything 8 Do not carry your computer by holding any of its protruding elements Heat dispersal User s Manual To protect against overheating the processor is equipped with an internal temperature sensor which activates a cooling fan or lowers the processing speed if the computer s internal temperature rises to a certain level You are able to select whether to control this temperature by either turning on the fan first then if necessary lowering the processor speed or by lowering the processor speed first then if necessary turning on the fan Both of these functions are controlled through the Power Options 3 50 T User s Manual When the processor s temperature falls within n
112. fore proceeding USB Flash Memory will be formatted and all the data in the USB Flash Memory will be lost when proceeding Turn on your computer and allow it to load the Windows 7 operating system from the hard disk drive as normal Insert the first blank disc into the optical disc drive tray or insert the USB Flash Memory into one available USB port Double click the Recovery Media Creator icon on the Windows 7 desktop or select the application from Start Menu After Recovery Media Creator starts select the type of media and the title you wish to copy and then click the Create button 4 29 Restoring the pre installed software from your created Recovery Media User s Manual If the pre installed files are damaged you are able to either use the Recovery Media you have created or the hard disk drive recovery process to restore the computer to the state it was in when you originally received it To perform this restoration follow the steps below When the sound mute feature has been activated by pressing the FN ESC key be sure to disable this to allow sounds to be heard before starting the restore process Please refer to The Keyboard in Chapter 3 Operating Basics for further details You can not use System Recovery Options if restoring the pre installed software without System Recovery Options When you reinstall the Windows operating system the hard disk will be reformatted and all data will be lost 1 Load the Recov
113. gerprint information Delete the fingerprint data for the currently logged in user Click Start gt All Programs gt TOSHIBA gt Tools amp Utilities gt Fingerprint Utility or double click the utility icon in the Taskbar Swipe your finger across the fingerprint sensor 3 The TOSHIBA Fingerprint Utility main menu is displayed Select Enroll in the main menu 4 Inthe Enroll window it enables you to delete the fingerprint data for the currently logged in user Click an enrolled finger you want to delete Are you sure you want to delete this fingerprint template message box will appear on the screen and then click OK If you want to delete other fingerprints repeat this step If only one fingerprint is registered the message Sorry At least one fingerprint is required will appear after clicking OK You are not allowed to delete a unique fingerprint Click Close 6 Are you sure you want to quit is displayed Click OK It will be returned to the TOSHIBA Fingerprint Utility main menu a Delete all users fingerprints 1 Inthe TOSHIBA Fingerprint Utility main menu click Run as administrator in the lower left User Account Control window is displayed Click Yes Swipe your enrolled finger Select Fingerprint Control option A list of fingerprint information for all users is shown in the screen Click Delete All in the lower right Are you sure you want to delete all fingerprints message box will app
114. hange the TPM setting when the Hide TPM setting is currently set to Yes switch the Hide TPM setting from Yes to No Open TOSHIBA Security Assist Start gt All Programs gt TOSHIBA gt Tools amp Utilities gt Security Assist and select TPM Settings By enabling TPM the required software gets installed You may not have all the softwares listed above depending on the model you purchased Special features User s Manual The following features are either unique to TOSHIBA computers or are advanced features which make the computer more convenient to use Access each function using the following procedures 1 To access the Power Options click Start gt Control Panel gt System and Security gt Power Options eco button Press this button to launch the TOSHIBA eco Utility This button changes On and Off of eco Mode TOSHIBA The TOSHIBA Presentation button has the same Presentation button functionality as the Connect display button in the Mobility Center Hot keys Hot keys are specific key combinations that let you quickly change the system configuration directly from the keyboard without running a system program Display automatic This feature automatically cuts off power to the power off computer s display panel when there is no keyboard input for a specified time with power being restored the next time a key is pressed This can be specified in the Power Options HDD automatic power This feature automa
115. hat support the Sleep and Charge function hereinafter called compatible ports Compatible ports are USB ports that have the symbol icon You can use the Sleep and Charge function to charge certain USB compatible external devices such as mobile phones or portable digital music players However the Sleep and Charge function may not work with certain external devices even if they are compliant with the USB specification In those cases turn the power of the computer ON to charge the device m When Sleep and Charge function is enabled USB bus power DC5V will be supplied to compatible ports even when the power of the computer is turned OFF USB bus power DC5V is similarly supplied to the external devices which are connected to the compatible ports However some external devices cannot be charged solely by supplying USB bus power DC5V As for the specifications of the external devices please contact the device manufacturer or check the specifications of the external devices thoroughly before use m Using the sleep and charge function to charge external devices will take longer than charging the devices with their own chargers m If Sleep and Charge function is enabled the computer s battery will discharge during hibernation or when the computer is turned off It is recommended that you connect the AC adaptor to the computer when enabling the Sleep and Charge function D External devices connected to the USB bus power D
116. he Battery indicator glows green Repeat these steps two or three times until the battery recovers normal capacity Monitoring battery capacity Remaining battery power can be monitored using the following methods BR Clicking the battery icon on the Taskbar BR Via the Battery Status in the Windows Mobility Center window You should wait at least 16 seconds after turning on the computer before trying to monitor the remaining operating time This is because the computer needs this time to check the battery s remaining capacity and then calculate the remaining operating time based on this together with the current power consumption m Please be aware that the actual remaining operating time may differ slightly from the calculated time With repeated discharges and recharges the battery s capacity will gradually decrease In view of this it will be noted that an often used older battery will not operate for as long as a new battery even when both are fully charged Maximizing battery operating time User s Manual A battery s usefulness depends on how long it can supply power on a single charge while how long the charge lasts in a battery depends on m Processor speed Screen brightness System Sleep Mode System Hibernation Mode Display power off period Hard disk drive power off period How often and for how long you use the hard disk drive and external disk c drives for example optical disc and floppy diskette drive
117. he Control window s Top Menu or Menu buttons touch pad and mouse menu operations may not be able to be used Open TOSHIBA VIDEO PLAYER Manual Modem i TOSHIBA VIDEO PLAYER features and instructions are explained in details in TOSHIBA VIDEO PLAYER Manual Use the following procedure to open TOSHIBA VIDEO PLAYER Manual Press the F1 key when TOSHIBA VIDEO PLAYER is launched and click the Help button This section describes how to connect and disconnect the internal modem to and from a telephone jack Modem functions cannot be used in models which are not equipped with a modem Region selection A User s Manual Telecommunication regulations vary from one region to another so you will need to make sure the internal modem s settings are correct for the region in which it will be used The built in modem can be used only in specified countries and regions Using the modem in an area not specified for use may cause a system failure Check the specified areas carefully before using it To select a region follow the steps as detailed below 1 Click Start gt All Programs gt TOSHIBA gt Network amp Connectivity gt Modem Region Select 3 24 If it is available do not use the Country Region Select function included as part of the modem setup utility within the Control Panel if you change the country region setting this way you may find that the change does not take effect 2 The Region Selection icon wil
118. he computer 2 Ensure that the battery pack is securely in place and the battery lock is in its locked position 3 Turn your computer over Power up modes The computer has three different power up modes as follows BR Shut Down Mode The computer will shut down without saving data in view of this you must always save your work before you turn the computer off BR Hibernation Mode Data in memory will be saved to the hard disk drive m Sleep Mode Data will be maintained in the computer s memory 1 Please refer to the sections Turning on the power and Turning off the J power in Chapter 1 Getting Started for further information Windows utilities You can configure various settings associated with both Sleep Mode and Hibernation Mode within the Power Options to access it Start gt Control Panel gt System and Security gt Power Options Hot keys You can use the FN F3 hot key to enter Sleep Mode or FN F4 to enter Hibernation Mode User s Manual 5 9 Panel power on off You can set up your computer so that power is turned off automatically when you close the display panel and turned on again when you open it Please note that this function is only available for Sleep Mode or Hibernation Mode not for Shut Down Mode T If the panel power off function is enabled and you manually shut down Windows do not close the display panel until the shut down process has been completed System automatic Sleep Hiberna
119. he enrolled fingers cannot be read you should instead log into the computer by using the keyboard to input the password If you are still unable to resolve the problem contact TOSHIBA Support In addition to the information in this section please also refer to the documentation supplied with your USB device User s Manual Problem USB device does not work Procedure Remove the USB device from the computer and then reconnect it to a free port in order to ensure it is firmly attached Ensure that any required USB device drivers are properly installed to achieve this you should refer to both the device documentation and the operating system documentation Sleep and Charge function For more information and settings please refer to the Using the TOSHIBA Sleep Utility section in Chapter 4 Utilities amp Advanced Usage Problem cannot use the Sleep and Charge function Procedure Sleep and Charge function may be disabled Select the Enable Sleep and Charge check box in the TOSHIBA Sleep utility to enable this function When there is a current overflow of the external device connected to the compatible port USB bus power DC5V supply may be stopped for safety reasons When this happens disconnect an external device if some external devices are connected After that turn the power of the computer ON OFF to restore the function If this function can not be still used even if only one external device is
120. her Radio Stations 1 Before using this equipment ensure that it does not interfere with any of the equipment listed above 2 If this equipment causes RF interference to other radio stations promptly change the frequency being used change the location of use or turn off the source of emissions 3 Contact an authorized TOSHIBA service provider if you have problems with interference caused by this product to Other Radio Stations 2 Indication for Wireless LAN The indication shown below appears on this equipment DOOM LC 2 ADS OF 4 LGE Ee 1 2 4 This equipment uses a frequency of 2 4GHz 2 DS This equipment uses DS SS modulation Vo OF This equipment uses OFDM modulation 4 The interference range of this equipment is less than 40m 5 mmm This equipment uses a frequency bandwidth from 2 400MHz to 2 483 5MHz It is possible to avoid the band of mobile object identification systems gt 3 Indication for Bluetooth The indication shown below appears on this equipment SESCH De 2 4 This equipment uses a frequency of 2 4 GHz FH This equipment uses FH SS modulation 1 The interference range of this equipment is less than 10 m EE This equipment uses a frequency bandwidth from 2 400 MHz to 2 483 5 MHz It is impossible to avoid the band of mobile object identification systems pa COS 4 About the JEITA 5GHz Wireless LAN supports W52 W53 W56 Channel IEEE802
121. here are some limitations on the settings at BIOS Setup lf it is required to use BIOS Setup please do not use Hi Speed Start Mode Please execute BIOS Setup after Windows shut down BH Before using Hi Speed Start Mode please finish all the running programs RB fyou set the boot up certification single sign on on the model featured with a fingerprint authentication a fingerprint or password is required again at the login phase User s Manual TOSHIBA Peak Shift Control TOSHIBA Button Support TOSHIBA PC Diagnostic Tool TOSHIBA Password Utility TOSHIBA Flash Cards HW Setup TOSHIBA Accessibility TOSHIBA Peak Shift Control is a function that can help reduce power usage during periods of peak demand by shifting some power consumption to periods when demand is lower For instance in peak hours of power consumption such as in the daytime in the summer the power consumed from the AC power source is automatically stopped and the battery is used for PC operation The AC power can then be used to charge the battery during periods where power demand is reduced such as at night thereby reducing the load during peak periods To access the utility click Start gt All Programs gt TOSHIBA gt Tools amp Utilities gt Peak Shift Control For more information please refer to the help file This utility controls the following computer button functions E Eco button m TOSHIBA Presentation button
122. here is no recovery partition TOSHIBA support If you require any additional help using your computer or if you are having problems operating the computer you may need to contact TOSHIBA for additional technical assistance Before you call User s Manual Procedure You will see this message if you have previously chosen to remove the partition and are trying to create Recovery Media When there is no recovery partition the Recovery Media Creator cannot make Recovery Media However if you have already created a Recovery Media you can use it to restore the recovery partition Simply follow the instructions in Restoring the pre installed software from your created Restoring the pre installed software from your created Recovery Media section in chapter 4 Utilities amp Advanced Usage You will be directed to select Restore Original Factory Image from the drop down menu If you have not created Recovery Media please contact TOSHIBA support for assistance Some problems you experience may be related to software or the operating system so it is important that you investigate other sources of assistance first Before contacting TOSHIBA try the following D Review troubleshooting sections in the documentation supplied with your software and or peripheral devices BR fa problem occurs when you are running software applications consult the software documentation for troubleshooting suggestions and consider cal
123. ice Station This utility is able to either enable or disable the Sleep and Charge function Sleep and Charge By connecting to the USB port devices such as digital audio players are able to charge even when the computer is in Sleep Mode Hibernation Mode or shutdown state To access this utility click Start gt All Programs gt TOSHIBA gt Tools amp Utilities gt Sleep Utility Bulletin Board is a convenient place to pin things to visually organize in a fun and creative way Simply drag and drop your favorite pictures files or notes to pin them on the Board You can use it to create thumbnail shortcuts reminders to do list and so on according to your personal style To access this utility click Start gt All Programs gt TOSHIBA gt Tools amp Utilities gt Bulletin Board User s Manual TOSHIBA ReelTime TOSHIBA Wireless LAN Indicator TOSHIBA Media Controller TOSHIBA Resolution Plug in for Windows Media Player Trusted Platform Module TPM This application is a graphical history indexing tool that enables you to view recently accessed files in a fun and easy to use format View and scroll through your history of opened or imported files via thumbnails in an intuitive user interface To access this utility click Start gt All Programs gt TOSHIBA gt Tools amp Utilities gt ReelTime TOSHIBA Wireless LAN Indicator utility displays the system s Wireless LAN connection stat
124. ick on the Skip button in the Registration screen 3 Click the Next button to start the guide Please follow the guide to practice Click the Back button to practice the guide once more 4 Click the Next button to start image capturing process Adjust the position of your face so that it fits within the face shaped frame 5 Once your face has been positioned properly the recording will commence Start moving your neck very slightly to the left and right and then move your neck up and down 6 Registration will end after you have repeatedly moved your neck left right up and down When the register succeeds below message will be displayed on the screen Registration successful Now we ll do the verification test Click the Next button Click the Next button to perform the verification test 7 Perform the verification test Face the screen as you do when you register If verification fails click the Back button and re register Please refer to step 6 from step 4 8 If verification is successful click the Next button and register an account 9 Register the account Fill in all the fields User s Manual 4 13 10 The Management screen is displayed The registered account name will be displayed Clicking on it will cause the captured image of your face to be displayed on the left How to Delete the Face Recognition Data Delete image data account information and personal record data created during registration To d
125. ime in the System Time field Your computer will 4 Press F10 a confirmation message will be automatically power displayed off after 1 minute 5 Press the ENTER key the BIOS setup and the same application will end and the computer will message will appear restart again the next time when it is turned on Keyboard Keyboard problems can be caused by the setup and configuration of the computer please refer to the section The Keyboard in Chapter 3 Operating Basics for further information Problem Procedure Some letter keys Check that the numeric keypad overlay is not produce numbers activated press the FN F11 hot key and try typing again Output to screenis Please refer to your software s documentation to garbled ensure that it is not remapping the keyboard in any way remapping involves changing or reassigning the function of each key If you are still unable to use the keyboard you should contact TOSHIBA Support Internal display panel Apparent computer s display panel problems may be related to the computer s setup and configuration please refer to the HW Setup section in Chapter 4 Utilities amp Advanced Usage for further information User s Manual 6 7 Problem Procedure No display Press the FN F5 hot keys to adjust the display priority and to make sure it is not set for output to an external monitor Markings appear on These marks may have come from contact with the the computer s keyboard
126. int the hotkeys FN F1 to F12 do not work They will function after you enter the password 2 Enter the Password 3 Press ENTER A If you enter the password incorrectly three times in a row or if you dont enter the password within 1 minute the computer shuts off In this case some features that can power on the computer automatically Wake up on LAN Task Scheduler etc may not work You must turn the computer back on to retry password entry HW Setup T This section explains how to use the TOSHIBA HW Setup program to configure your computer and provides information on settings for various functions After you changed the settings of HW Setup a dialog box may appear to prompt you that the changes will take effect after the computer is restarted Make sure to restart your computer immediately to apply these changes Accessing HW Setup To run the HW Setup program click Start gt All Programs gt TOSHIBA gt Tools amp Utilities gt HWSetup HW Setup window User s Manual The HW Setup window contains a number of tabs General Display CPU Boot Setting Keyboard LAN SATA USB and Advanced to allow specific functions of the computer to be configured In addition there are also three buttons OK Cancel and Apply OK Accepts your changes and closes the HW Setup window Cancel Closes the window without accepting your changes Apply Accepts all your changes without closing the HW Setup window G
127. inting device User s Manual Procedure Remove the PC Card from the computer and then reinsert it in order to ensure it is firmly connected In the event that the PC Card is attached to an external peripheral device ensure that this connection is properly made If the problem persists then you should refer to the documentation supplied with your PC Card for further information If you are still unable to resolve the problem contact your reseller dealer or service provider If you are using a USB mouse you should also refer to both the USB mouse section in this chapter and the documentation supplied with your mouse Touch Pad Problem The Touch Pad does not work On screen pointer does not respond to pointing device operation Double tapping does not work Procedure Check the Device Select settings Click Start gt Control Panel gt Hardware and Sound gt Mouse Pressing FN F9 to enables In this instance the system might be busy Try moving the mouse again after waiting a short while In this instance you should initially try changing the double click speed setting within the Mouse Control utility 1 To access this utility click Start gt Control Panel gt Hardware and Sound gt Mouse 2 Within the Mouse Properties window click the Buttons tab 3 Set the double click speed as required and click OK User s Manual Problem The on screen pointer moves too fast or t
128. isplayed This will switch the password input screen across to the keyboard based one m You must ensure that you use the TOSHIBA Password Utility to register a User Password before using the Fingerprint Pre Boot Authentication and its extended function to allow fingerprints to be used to access the computer when it is turned on BR When swiping your finger please ensure that you do it slowly and at a constant speed If you find that this does not improve the authentication rate you should try to adjust the speed at which the finger is swiped m f there are any changes in the environment or settings related to authorization you will be required to provide authorization information such as a User Password and if applicable the HDD Hard Disk Drive password Overview about Fingerprint Single Sign on feature This is a feature that allows the user to complete the authentication for both the User BIOS Password and if applicable the HDD Hard Disk Drive Password and logging onto Windows using only one fingerprint authentication when booting up It is necessary to register the User BIOS Password and Windows Logon Password before using the Fingerprint Pre Boot Authentication and this Fingerprint Single Sign On Feature Please use the TOSHIBA Password Utility to register your User BIOS Password If Windows Logon is not the default for your system see Manual to register your Windows Logon Password Only one fingerprint authenticatio
129. itor or an optical digital device m Use the audio video control button to reproduce music or voice Open the optical disc drive RH Do not use shut down log off Sleep Mode or Hibernation Mode functions while writing or rewriting E Make sure that the writing rewriting operation is completed before going into either Sleep Mode or Hibernation Mode You can remove an optical media on the optical disc drive after writing is completed fthe media is of poor quality or is dirty or damaged writing or rewriting errors may occur BH Set the computer on a level surface and avoid places subject to vibration such as airplanes trains or cars In addition do not use the computer on an unstable surface such as a stand E Keep mobile phones and other wireless communication devices away from the computer TOSHIBA Disc Creator User s Manual Please be aware of the following limitations when you use the TOSHIBA Disc Creator BH DVD Video cannot be created using TOSHIBA Disc Creator m DVD Audio cannot be created using TOSHIBA Disc Creator m You cannot use TOSHIBA Disc Creator s Audio CD function to record music to DVD R DVD R DL DVD RW DVD R DVD R DL or DVD RW media RH Do not use the Disc Backup function of TOSHIBA Disc Creator in order to copy DVD Video or DVD ROM material that has copyright protection BH DVD RAM discs cannot be backed up using the Disc Backup function of TOSHIBA Disc Creator 3 20 You cannot bac
130. k up CD ROM CD R or CD RW media to DVD R DVD R DL or DVD RW media using the Disc Backup function of TOSHIBA Disc Creator You cannot back up CD ROM CD R or CD RW media to DVD R DVD R DL or DVD RW media using the Disc Backup function of TOSHIBA Disc Creator You cannot back up DVD ROM DVD Video DVD R DVD R DL DVD RW DVD R DVD R DL or DVD RW to CD R or CD RW media using the Disc Backup function of TOSHIBA Disc Creator TOSHIBA Disc Creator cannot record in packet format You might not be able to use the Disc Backup function of TOSHIBA Disc Creator to back up a DVD R DVD R DL DVD RW DVD R DVD R DL or DVD RW disc that was made with other software on a different optical media recorder If you add data to a DVD R DVD R DL DVD R or DVD R DL disc that you have already recorded to you might not be able to read the added data under some circumstances For example it cannot be read under 16 bit operating systems such as Windows 98SE and Windows Me while in Windows NT4 you will need Service Pack 6 or later and in Windows 2000 you will need Service Pack 2 In addition to this some DVD ROM and DVD ROM CD R RW drives cannot read this added data regardless of the operating system TOSHIBA Disc Creator does not support recording to DVD RAM discs to achieve this you should use Windows Explorer or another similar utility When you back up a DVD disc be sure that the source drive supports recording to DVD R DVD R DL DVD RW DVD
131. key combination uses AC adaptor battery LCD fan HDD sound volume wireless communication functionalities TOSHIBA Express Port Replicator and USB information date of initial system use and also computer and device usage i e power settings battery temperature and recharging CPU memory backlight illumination time and temperatures for various devices The stored data uses a very small portion of the total hard disk capacity approximately 10MB or less per year This information is used to identify and provide a notification of system conditions which may effect the performance of your TOSHIBA computer It 4 23 may also be used to help diagnose problems should the computer require service by TOSHIBA or TOSHIBA s authorized service providers Additionally TOSHIBA may also use this information for quality assurance analysis Subject to the use restrictions above the HDD data logged may be transferred to entities located outside of your country or region of residence e g European Union Those countries may or may not have the same data protection laws or data protection levels as required by your home country or region Once enabled you may disable the TOSHIBA PC Health Monitor at any time by uninstalling the software via Uninstall a program in the Control Panel Doing so will automatically delete all collected information from the HDD The TOSHIBA PC Health Monitor software does not extend or modify TOSHIBA s obligations u
132. l appear in the Windows Taskbar 3 Click the icon with the primary left mouse button to display a list of regions that the modem supports together with a sub menu which details telephony location information a check mark will appear next to the currently selected region and telephony location 4 Select either a region from the region menu or a telephony location from the sub menu m When you click a region it becomes the modem s default selection for any new dialling locations that are created within the Windows Control Panel Phone and Modem Options m When you select a telephony location the corresponding region is automatically selected and becomes the modem s default setting Properties menu Click the icon with the secondary right mouse button in order to display a Properties menu on the screen Setting User s Manual Within the Properties menu you are able to either enable or disable the following settings AutoRun Mode Allows you to configure whether the Modem Region Select utility starts automatically whenever you start up the operating system Open the Dialing Properties dialog box after selecting region Allows you to configure whether the dialing properties dialog box will be displayed automatically after you have selected a region Location list for region selection Displays a sub menu appears which details location information Open dialog box if the modem and Telephony Current Location region
133. leep Mode Data is stored in RAM so if the computer loses power it could be lost E In Hibernation Mode data will be lost if you remove the battery pack or disconnect the AC adaptor before the save is completed Wait for the Hard Disk Drive Optical Disc Drive eSATA indicator to go out Do not touch the battery release latch while holding the computer or the battery pack might fall out due to the unintentional release of the battery release latch and cause injuries Removing the battery pack To remove a discharged battery follow the steps as detailed below 1 Save your work 2 Turn the computer s power off ensure that the Power indicator is off 3 Remove all cables and peripherals that are connected to the computer 4 Close the display panel and turn the computer upside down Slide the battery lock into its unlocked e position 6 Slide and hold the battery release latch to disengage the battery pack and then remove it from the computer a User s Manual 5 8 Figure 5 1 Releasing the battery pack 1 Battery lock 3 Battery pack 2 Battery release latch Installing the battery pack To install a battery pack follow the steps as detailed below Do not touch the battery release latch while holding the computer or the battery pack might fall out due to the unintentional release of the battery release latch and cause injuries 1 Insert the battery pack as far as it will go into t
134. left side of the computer el Te te Le 1 Universal Serial Bus USB 3 0 port 4 Mini DisplayPort 2 eSATA USB combo port 5 ExpressCard slot or PC Card slot 3 Cooling vents 6 PC Card eject button Provided with some models Product appearance depends on the model you purchased oe Universal Serial Bus One Universal Serial Bus port which complies to USB 3 0 port the USB 3 0 standard is provided on the left side of the computer The USB 3 0 port is compliant with USB 3 0 standard and backward compatible with USB 2 0 devices estas 4 eSATA USB combo One eSATA USB combo port which complies to port the USB 2 0 standard is provided on the left side of the computer This port with the icon 4 supports the following functions BR USB Sleep and Charge function m System ON CDP Charge Mode Cooling vents The cooling vents help the processor to avoid overheating Do not block the cooling vents Keep foreign metal objects such as screws staples and paper clips out of the cooling vents Foreign metal User s Manual 2 3 objects can create a short circuit which can cause damage and fire possibly resulting in serious injury Mini DisplayPort ExpressCard slot PC Card slot PC Card eject button Right side The following figure shows the computer s right side User s Manual This port is capable of driving resolutions up to 2560x1600 With a suitable adapter Mini DisplayPort may be u
135. ling the software company s technical support department for assistance BR Consult the reseller or dealer from where you purchased your computer and or software they are your best resource for current information and support 6 20 TOSHIBA technical support If you are still unable to solve the problem and suspect that it is hardware related visit TOSHIBA technical support website http www toshiba co jp worldwide User s Manual 6 21 Appendix A Specifications This appendix summarizes the Computere technical specifications Physical Dimensions Physical Dimensions shown below do not include parts that extend beyond the main body Size 374 w x 250 5 d x 33 4 37 6 h millimeters not including parts that extend beyond the main body Environmental Requirements Conditions Ambient temperature Relative humidity Operating 5 C 41 F to 35 C 20 to 80 95 F noncondensing Non operating 20 C 4 F to 60 C 10 to 90 140 F noncondensing Wet bulb temperature 29 C maximum Conditions Altitude from sea level Operating 60 to 3 000 meters Non operating 60 to 10 000 meters maximum Power Requirements AC adaptor 100 240V AC 50 or 60 Hz cycles per second Computer 15V DC User s Manual A 1 Built in Modem 7 This information is applicable to the models equipped with a built in J modem Network control unit NCU Type of NCU AA Type of line Telephone line analog only Type of dialing Pul
136. low orange while the battery is being charged Use only the computer connected to an AC power source or optional TOSHIBA Battery charger to charge the battery pack Never attempt to charge the battery pack with any other charger Time Refer to User Information Guide about Charging time Battery charging notice The battery may not begin charging immediately under the following conditions BR The battery is extremely hot or cold if the battery is extremely hot it might not charge at all To ensure the battery charges to its full capacity you should charge it at room temperature of between 5 C to 35 C 41 F to 95 F BH The battery is nearly completely discharged In this instance you should leave the AC adaptor connected for a few minutes and the battery should begin charging The Battery indicator may show a rapid decrease in battery operating time when you try to charge a battery under the following conditions BH The battery has not been used for a long time E The battery has completely discharged and been left in the computer for a long time A cool battery is installed in a warm computer In such cases you should follow the steps as detailed below 1 Fully discharge the battery by leaving it in the computer with the power on until the system automatically turns itself off 2 Connect the AC adaptor to the DC IN 15V jack of the computer and to a wall outlet that is supplying power 3 Charge the battery until t
137. lt device click the Set Default Device button under the chosen device tab Information Click the Information button to view hardware information software information and language setting 3 48 Power Management The audio controller in your computer can be turned off when the audio function is not used To adjust the configuration of audio power management click the Power Management button m When audio power management is enabled the circle button at the upper left of the Power Management is blue and convex m When audio power management is disabled the button is black and concave Speaker Configuration Click the Auto Test button to confirm the internal speakers or the headphone sound is coming from the right direction Default Format You can change the sample rate and bit depth of sound Video mode T Video mode settings are configured via the Screen Resolution dialog To open the Screen Resolution dialog click Start gt Control Panel gt Appearance and Personalization gt Display gt Change display settings If you are running some applications for example a 3D application or video playback and so on you may see some disturbance flickering or frame dropping on your screen If that occurs adjust the resolution of display lowering it until the screen is displayed properly Disabling Windows Aero may also help correct this issue Computer Handling This section explains computer
138. mmunications DOC regulations provide that changes or modifications not expressly approved by TOSHIBA Corporation could void your authority to operate this equipment This Class B digital apparatus meets all requirements of the Canadian Interference Causng Equipment Regulations Cet appareil num rique de la class B respecte toutes les exgences du R glement sur le mat riel brouileur du Canada Modem warning notice T User s Manual This information is applicable to the models equipped with a built in modem Conformity Statement The equipment has been approved to Commission Decision CTR21 for pan European single terminal connection to the Public Switched Telephone Network PSTN However due to differences between the individual PSTNs provided in different countries regions the approval does not of itself give an unconditional assurance of successful operation on every PSTN network termination point In the event of problems you should contact your equipment supplier in the first instance Network Compatibility Statement This product is designed to work with and is compatible with the following networks It has been tested to and found to conform with the additional requirements conditional in EG 201 121 Germany ATAAB ANO05 AN006 AN007 AN009 AN010 and DE03 04 05 08 09 12 14 17 Greece ATAAB ANO05 ANO006 and GRO1 02 03 04 Portugal ATAAB ANO01 005 006 007 011 and P03 04 08 10 Spain ATAAB ANO05 007 012 and ESO
139. mption and its highest speed Always Low The processor s automatic clock speed switching function is disabled in use the processor will always run at a lower level of power consumption and a low speed Boot Setting This function allows you to modify the boot settings Boot Priority Options This tab allows you to set the priority for booting the computer The Boot Priority Options setting window will be displayed Click the up and down arrow buttons to adjust the priority To change the boot drive follow the steps below T User s Manual 1 Hold down F12 and boot the computer when the TOSHIBA Leading Innovation gt gt gt screen appears release the F12 key 2 Use the up and down cursor keys to select the boot device you want and press ENTER If a Supervisor Password has been set manual boot device selection functions may be restricted The boot device selection methods described above will not change the boot priority settings that have been configured in HWSetup In addition if you press a key other than one of those listed or if the selected device is not installed the system will continue to boot according to the current and available settings in HW Setup USB Memory BIOS Support Type This option allows you to set the type of the USB memory to be used as a startup device HDD Sets the USB memory to be the equivalent of a hard disk drive default With this setting the USB memory device can be used to st
140. n is required to replace the User BIOS Password and if applicable the HDD Hard Disk Drive Password and the Windows Logon Password How to Enable Fingerprint Pre Boot Authentication and Single Sign On feature It is necessary to first enroll your fingerprint with the TOSHIBA Fingerprint Utility prior to enabling and configuring the Pre Boot Authentication and Single Sign On feature You should check that your fingerprint is enrolled before configuring the settings 1 Logon as Administrator means a user has administrator privileges 2 Click Start gt All Programs gt TOSHIBA gt Tools amp Utilities gt Fingerprint Utility 3 Swipe your finger across the fingerprint sensor A The TOSHIBA Fingerprint Utility main menu is displayed Click Run As Administrator in lower left User Account Control window is displayed Click Yes Swipe your finger across the fingerprint sensor 7 Select Setting in the main menu to open the Setting window you can an Select Pre Boot Authentication check box if you want to use the fingerprint Pre Boot Authentication feature Select Pre Boot Authentication and Single sign on check boxes if you want to use the Single Sign on feature 8 Click Apply 9 Save succeeded is displayed Click OK 10 Click Close 11 Are you sure you want to quit is displayed Click OK It will be returned to the TOSHIBA Fingerprint Utility main menu This modified configuration for fingerprint Pr
141. n serious injury Follow the instruction of your medical device when using any wireless functionality D Always turn off wireless functionality if the computer is near automatic control equipment or appliances such as automatic doors or fire detectors Radio waves can cause malfunction of such equipment possibly resulting in serious injury m t may not be possible to make a network connection to a specified network name using the ad hoc network function If this occurs the new network will have to be configured for all computers connected to the same network in order to re enable network connections Please be sure to use new network name Wireless LAN The Wireless LAN is compatible with other LAN systems based on Direct Sequence Spread Spectrum Orthogonal Frequency Division Multiplexing User s Manual 3 27 T User s Manual radio technology that complies with the IEEE802 11 Wireless LAN standard E Frequency Channel Selection of 5GHz for IEEE 802 11a or and IEEE802 11n E Frequency Channel Selection of 2 4GHz for IEEE 802 11b g or and IEEE802 11n E Roaming over multiple channels m Card power management BR Wired Equivalent Privacy WEP data encryption based on an 128 bit encryption algorithm m Wi Fi Protected Access WPA The transmission speed over the wireless LAN and the distance over which the wireless LAN can reach may vary depending on surrounding electromagnetic environment obstacles access point de
142. nc Wi Fi is a registered trademark of the Wi Fi Alliance Secure Digital and SD are trademarks of SD Card Association Memory Stick Memory Stick Duo Memory Stick PRO Memory Stick PRO Duo and Memory Stick Micro are trademarks or registered trademarks of Sony Corporation xD Picture Card is a trademark of FUJIFILM Corporation ExpressCard is a trademark of PCMCIA MultiMediaCard and MMC are trademarks of MultiMediaCard Association FCC User s Manual QUALCOMM is a trademark of Qualcomm Incorporated registered in the United States and other countries ATHEROS is a trademark of Qualcomm Atheros Inc registered in the United States and other countries Realtek is a registered trademark of Realtek Semiconductor Corporation Other trademarks and registered trademarks not listed above may be used in this manual information FCC notice Declaration of Conformity Information This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cau
143. nder its standard limited warranty in any way TOSHIBA s standard limited warranty terms and limitations apply Starting the TOSHIBA PC Health Monitor The TOSHIBA PC Health Monitor can be started using the following methods BH Click Start gt All Programs gt TOSHIBA gt Support amp Recovery gt PC Health Monitor BR Click the icon in the notification area then click the Enable PC Health Monitor message the first time you run the application and Run PC Health Monitor every time thereafter No matter which method is used the TOSHIBA PC Health Monitor explanation screen will be displayed Clicking Next will display the PC Health Monitor Software Notice amp Acceptance screen Please carefully read the information displayed Selecting ACCEPT and clicking OK will enable the program By enabling the TOSHIBA PC Health Monitor software you agree with these terms and conditions and to the use and sharing of the collected information Once the program is enabled the TOSHIBA PC Health Monitor screen is displayed and the program will begin monitoring system functions and collecting information If a TOSHIBA PC Health Monitor message is displayed A message will be displayed if any changes which may interfere with the operation of the program are detected Follow the instructions displayed on screen in the message Cleaning the cooling module This section explains how to clean the cooling module User s M
144. nments before use In the case of automobiles or aircraft the manufacturer or airline respectively should be asked for permission before use of this product Furthermore for general safety reasons the use of this product in environments with explosive atmospheres is not permitted VCCI Class B Information CORBIS PIZABFRARMRE CT COREIA KERK TCE Bd LS BW ECLCWETA CORBMNISAPTLE VAL EE CRA SNSL SESS SSROFCEMBVET Bus SEI ACEL LN RY RWSL TEAL VCCI B Video Standard Notice User s Manual THIS PRODUCT IS LICENSED UNDER THE AVC THE VC 1 AND MPEG 4 VISUAL PATENT PORTFOLIO LICENSE FOR THE PERSONAL AND NON COMMERCIAL USE OF A CONSUMER FOR I ENCODING VIDEO IN COMPLIANCE WITH THE ABOVE STANDARDS VIDEO AND OR II DECODING AVC VC 1 AND MPEG 4 VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONAL AND NON COMMERCIAL ACTIVITY AND OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED BY MPEG LA TO PROVIDE SUCH VIDEO NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER USE ADDITIONAL INFORMATION INCLUDING THAT RELATING TO PROMOTIONAL INTERNAL AND COMMERCIAL USES AND LICENSING MAY BE OBTAINED FROM MPEG LA L L C SEE HTTP WWW MPEGLA COM vii Canadian regulatory information Canada only This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the Radio Interference Regulation of the Canadian Department of Communications Note that Canadian Department of Co
145. ns may result in data loss Before you install a device or application save any data in memory to the hard disk drive or other storage media Failure to do so may result in the loss of data Connecting the AC adaptor JN User s Manual Attach the AC adaptor when you need to charge the battery or you want to operate from AC power It is also the fastest way to get started because the battery pack will need to be charged before you can operate from battery power The AC adaptor can automatically adjust to any voltage ranging from 100 to 240V and to a frequency of either 50 or 60 Hz enabling you to use this computer in almost any country region The adaptor converts AC power to DC power and reduces the voltage supplied to this computer Always use the TOSHIBA AC adaptor that was included with your computer or use AC adaptors specified by TOSHIBA to avoid any risk of fire or other damage to the computer Use of an incompatible AC adaptor could cause fire or damage to the computer possibly resulting in serious injury TOSHIBA assumes no liability for any damage caused by use of an incompatible adaptor Never plug the AC adaptor into a power source that does not correspond to both the voltage and the frequency specified on the regulatory label of the unit Failure to do so could result in a fire or electric shock possibly resulting in serious injury Always use or purchase power cables that comply with the legal voltage and frequency
146. nsert a memory media follow the steps as detailed below 1 Turn the memory media so that the contacts metal areas are face down User s Manual 3 37 2 Insert the memory media into the memory media slot on the front of the computer 3 Press the memory media gently until you hear a click Figure 3 14 Inserting a memory media 1 Memory media slot 2 Memory media m Make sure memory media is oriented properly before you insert it If you insert the media in wrong direction you may not be able to remove it E When inserting memory media do not touch the metal contacts You could expose the storage area to static electricity which can destroy data BR Do not turn the computer off or switch to Sleep Mode or Hibernation Mode while files are being copied doing so may cause data to be lost Removing a memory media The following instructions apply to all types of supported media devices To remove a memory media follow the steps as detailed below 1 E AVN Open the Safely Remove Hardware and Eject Media icon on the Windows Taskbar Point to memory media and click the left Touch Pad control button Press the memory media to partially extend it out of the computer Grasp the media and remove it Make sure the Memory Media slot indicator is out before you remove the memory media or turn off the computer s power If you remove the memory media or turn off the power while the computer is accessing th
147. nual The computer is equipped with a memory media slot that can accommodate some kinds of memory media with various memory capacities so that you can easily transfer data from devices such as digital cameras and Personal Digital Assistants Keep foreign objects out of the memory media slot Never allow metal objects such as screws staples and paper clips to enter the computer or Keyboard Foreign metal objects can create a short circuit which can cause computer damage and fire possibly resulting in serious injury E Please note that an adaptor is required to use miniSD microSD Card Memory Stick Duo Memory Stick PRO Duo and Memory Stick Micro m Please note that not all memory media have been tested and verified to work correctly Therefore it is not possible to guarantee that all memory media will operate properly BR The slot for some models does not support Magic Gate functions Figure 3 13 Examples of memory media e RN Z amp lg D ZB HF a Q Ka Secure Digital SD microSD card adaptor MultiMediaCard Card and microSD card MMC Memory Stick xD picture card 3 35 Memory media T User s Manual This section provides the important safety precautions in order to handle your memory media Points to note about the memory media card SD SDHC SDXC memory cards comply with SDMI Secure Digital Music Initiative which is a technology adopted to prevent unlawful copy or playback of digital music For this reason
148. oard on an aircraft or in places where electronic devices are regulated or controlled always power off your computer BR When Intel Rapid Start Technology is enabled Wake up on LAN Wake up on USB or Wake up from Sleep Mode automatically functions are not available when the computer has been switched from Sleep Mode to Hibernation Mode The Windows cannot be restored normally if the battery is exhausted when the computer is moving from Sleep Mode to Hibernation Mode E The partition allocation on the Hard Disk Drive for the Intel Rapid Start Technology cannot be deleted even if Intel Rapid Start Technology is disabled E ntel Rapid Start Technology can be used only for Windows 7 E Intel Rapid Start Technology cannot be used in models that do not equipped with a Solid State Drive m The Windows restore time from Hibernation Mode depends on the amount of system memory used in the computer E After an additional memory module is installed the computer may not switch to Hibernation Mode normally by using Intel Rapid Start Technology In this case you can restore the system to factory default to re enable Intel Rapid Start Technology User s Manual Chapter 3 Operating Basics This chapter describes the basic operations of your computer highlights the precautions that should be taken when using it Using the Touch Pad To use the Touch Pad simply touch and move your fingertip across it in the direction you want
149. of the computer When the TOSHIBA HDD Protection detects computer vibration the Hard Disk Drive head is parked and the 3D object disk rotation will stop When the head is un parked the disk will begin to rotate again The 3D Viewer can be started from the icon in the task tray BR This 3D object virtually represents the Computer s internal Hard Disk Drive This representation may vary from the actual number of disks disk rotation head movement part size shape and direction m This feature may use a large amount of CPU and memory on some models The computer may become slow or sluggish when attempting to run other applications while the 3D Viewer is displayed m Intensely shaking the computer or other subjecting it to strong impacts may cause damage to the computer Details User s Manual To open the Details window click the Setup Detail button in the TOSHIBA HDD Protection Properties window Detection Level Amplification When the AC adaptor is disconnected or the lid is closed HDD Detection assumes that the computer will be carried and sets the detection level to the maximum for 10 seconds 4 27 HDD Protection Message Specify whether to display a message when TOSHIBA HDD Protection is active se This function does not work when the computer is booting in Sleep Mode T in Hibernation Mode in transition to Hibernation Mode recovering from Hibernation Mode or powered off Do not subject the computer to vibration o
150. omputer Press the ExpressCard gently to ensure a firm connection is made Figure 3 11 Inserting the ExpressCard iw Fw es 1 ExpressCard slot 2 ExpressCard After inserting the ExpressCard you should refer to its documentation and also check the configuration in Windows in order to ensure that it is correct Removing an ExpressCard To remove an ExpressCard follow the steps as detailed below 1 2 3 4 5 Open the Safely Remove Hardware and Eject Media icon on the Windows Taskbar Point to ExpressCard and click the left Touch Pad control button Press the ExpressCard in order to eject the ExpressCard partially out of the computer Grasp the ExpressCard and remove it Insert the Dummy card into the ExpressCard slot When you do not use an ExpressCard please be sure to insert a Dummy T card PC Card The computer may be equipped with a single PC Card slot that can accommodate a Type II format card Any PC Card that meets industry User s Manual 3 33 standards either manufactured by TOSHIBA or another vendor can be installed as the slot supports 16 bit PC Cards and 32 bit CardBus cards For reference CardBus supports the newer standard of 32 bit PC Cards and provides superior performance for the greater demands of applications such as multimedia data transmission PC Cards can sometimes become hot during computer operation Before you remove a PC Card always wait for it to cool You could get burned r
151. onfigured as a hidden recovery partition This partition stores files which can be used to restore pre installed software in the event of a problem If you subsequently set up your hard disk drive again do not change delete or add partitions in a manner other than specified in the manual otherwise you may find that space for the required software is not available In addition if you use a third party partitioning program to reconfigure the partitions on your hard disk drive you may find that it becomes impossible to setup your computer When the sound mute feature has been activated by pressing the FN ESC key be sure to disable this to allow sounds to be heard before starting the restore process Please refer to The Keyboard in Chapter 3 Operating Basics for further details You can not use System Recovery Options if restoring the pre installed software without System Recovery Options When you reinstall the Windows operating system the hard disk will be reformatted and all data will be lost Turn off your computer 2 While holding down 0 zero key on the keyboard turn on your computer 3 A menu will be displayed from which you should follow the on screen instructions User s Manual 4 31 Chapter 5 Power and Power Up Modes The computer s power resources include the AC adaptor battery pack and any internal batteries This chapter provides details on making the most effective use of these resources and in
152. oo slow The reaction of Touch pad is either too sensitive or not sensitive enough USB mouse Problem On screen pointer does not respond to mouse operation Double clicking does not work The on screen pointer moves too fast or too slow Procedure In this instance you should initially try changing the speed setting within the Mouse Control utility 1 To access this utility click Start gt Control Panel gt Hardware and Sound gt Mouse 2 Within the Mouse Properties window click the Pointer Options tab 3 Set the pointer speed as required and click OK Adjust the touch Sensitivity To access it click Start gt Control Panel gt Hardware and Sound gt Mouse If you are still unable to resolve the problem contact TOSHIBA Support Procedure In this instance the system might be busy Try moving the mouse again after waiting a short while Remove the mouse from the computer and then reconnect it to a free USB port in order to ensure it is firmly attached In this instance you should initially try changing the double click speed setting within the Mouse Control utility 1 To access this utility click Start gt Control Panel gt Hardware and Sound gt Mouse 2 Within the Mouse Properties window click the Buttons tab 3 Set the double click speed as required and click OK In this instance you should initially try changing the speed setting within the Mouse Control utili
153. or User s Manual Please be aware of the following considerations when using the fingerprint sensor A failure to follow these guidelines might result in damage to the sensor sensor failure fingerprint recognition problems or a lower fingerprint recognition success rate Do not scratch or poke the sensor with your nails or any hard or sharp objects Do not press the sensor strongly Do not touch the sensor with a wet finger or any wet objects keep the sensor surface dry and free from water vapor Do not touch the sensor with a soiled or dirty finger as minute foreign particles of dust and dirt may scratch it Do not paste stickers or write on the sensor Do not touch the sensor with a finger or any other object which may have a build up of static electricity on it Observe the following before you place your finger on the sensor whether for fingerprint enrollment registration or recognition Wash and dry your hands thoroughly Remove static electricity from your fingers by touching any metal surface Static electricity is a common cause of sensor failures especially when the weather is dry Clean the sensor with a lint free cloth do not use detergent or any other chemicals to clean the sensor Avoid the following finger conditions for enrollment or recognition as they may result in fingerprint enrollment errors or a drop in the fingerprint recognition success rate BH Soaked or swollen finger for example as may occur after t
154. ord User s Manual To start the utility point to or click the following items Start gt All Programs gt TOSHIBA gt Tools amp Utilities gt Password Utility User authentication may be required to validate user rights when using TOSHIBA Password Utility to delete or change passwords etc BR Set button Click this button to register a password After a password is set you will be prompted to enter it when you start the computer Check Set the same string simultaneously as the HDD User Password when setting the HDD User Password After you set the password a dialog box will be displayed asking whether you want to save it to a floppy diskette or other media If you forget the password you can open the password file on another computer Be sure to keep the media in a safe place When entering the character string to register the password enter from the keyboard character by character and do not enter as ASCII code or copy and paste the character string In addition ensure that the registered password is correct by outputting the character string to the password file When entering a password do not enter any characters for example TI or produced by pressing the SHIFT or ALT keys and so on Delete button Click this button to delete a registered password Before you can delete a password you must first enter the current password correctly Please use BIOS Setup to change or delete the HDD Passwords or to set
155. ormal range the fan will be turned off and the processor operation returned to its standard speed If the processor s temperature reaches an unacceptably high level with either setting the computer automatically shuts down to prevent any damage In this instance all unsaved data in memory will be lost 3 51 Chapter 4 Utilities amp Advanced Usage This chapter describes the utilities and special features of this computer and the advanced usage of some utilities Utilities and Applications T User s Manual This section describes the pre installed utilities that come with the computer and details how to start them For further information on their operation you may refer to each utility s online manual help files or README TXT file if applicable TOSHIBA Hi Speed Hi Speed Start Mode can make the computer Start start up faster than it would start up after a system shutdown E The efficient performance might not be expected with multiple user accounts registered E When system needs to be restarted because of Windows update drivers update or applications installation please Shut down or Only startup from built in HDD SSD supports Hi Speed Start Mode Restart accordingly If not those changes will not be reflected to the system properly with Hi Speed Start Mode E When setting password e g user password HDD password please enter it using keyboard E When the system is booting in Hi Speed Start Mode t
156. ort without USB Sleep and Charge function or disable both System ON CDP Charge Mode and USB Sleep and Charge function 4 22 F SATA This feature allows you to set conditions for SATA eSATA This feature allows you to enable disable the eSATA port Enabled Enables the eSATA port Default Disabled Disables the eSATA port in order to save power SATA Interface setting This feature allows you to set SATA interface setting Performance Let HDD work with maximum performance Default Battery life Let HDD work with battery life mode If this setting is selected this caused performance down Advanced This tab allows you to set the conditions for each device or function You can enable or disable the device or function you selected for power management Disabled mode consumes less power If you disable a device or function you must re enable it before you can use it again TOSHIBA PC Health Monitor User s Manual The TOSHIBA PC Health Monitor application proactively monitors a number of system functions such as power consumption battery health and the system cooling informing you of significant system conditions This application recognizes the system and individual component serial numbers and will track specific activities related to the computer and their usage The collected information includes device operation time and number of actuations or status changes i e number of power button and FN
157. ose to this switch as they may cause the computer to automatically enter Hibernation Mode and shut down even if the Panel Power Off feature is disabled Display hinges Power button TOSHIBA eco button TOSHIBA Presentation button volume down button volume up button Keyboard The display hinges allow the display panel to be positioned at a variety of easy to view angles Press this button to turn the computer s power on or off Press this button to launch the TOSHIBA eco Utility TOSHIBA eco Utility can be used only in Windows 7 The TOSHIBA Presentation button has the same functionality as the Connect display button in the Mobility Center Press this button to decrease the volume Press this button to increase the volume Your computer may intergrated with two kinds of keyboards A4 size keyboard which provides the embedded numeric overlay keys dedicated cursor control overlay keys amp and Keys full size keyboard which provides dedicated numeric keys dedicated cursor control keys amp and E Keys Refer to the The Keyboard section in Chapter 3 Operating Basics for details Touch Pad The Touch Pad located in the palm rest is used to control the movement of the on screen pointer For more information please refer to the Using the Touch Pad in Chapter 3 Operating Basics Touch Pad control The control buttons located below the Touch Pad buttons allow you to select menu items or manipulate text and
158. otes section in Appendix C P Please handle your computer carefully to avoid scratching or damaging the surface Front with the display closed The following figure shows the Computers front with its display panel in the closed position Figure 2 1 Front of the computer with display panel closed Co O0 Oo Oa Os 1 DC IN indicator 6 Memory media slot 2 Power indicator 7 Wireless communication indicator 3 Battery indicator 8 Wireless WAN indicator 4 Hard Disk Drive Optical Disc Drive 9 Microphone eSATA indicator 5 Memory media slot indicator 10 Stereo speakers Provided with some models Product appearance depends on the model you purchased User s Manual 2 1 s SE Y User s Manual DC IN indicator Power indicator Battery indicator Hard Disk Drive Optical Disc Drive eSATA indicator Memory media slot indicator Memory media slot Wireless communication indicator Wireless WAN indicator The DC IN indicator normally glows green when power is being correctly supplied from the AC power adaptor However if the output voltage from the adaptor is abnormal or if the computer s power supply malfunctions this indicator will flash orange The Power indicator normally glows green when the computer is turned on However if you turn the computer off into Sleep Mode this indicator will flash orange approximately two seconds on two seconds off The Batter
159. p at an angle 3 42 8 Grasp the module by its edges and remove it from the computer A m fyou use the computer for a long time the memory modules and the circuits locating close to the memory modules will become hot In this case let them cool to room temperature before you replace them Or you will get burnt if you touch any of them E Do not touch the connectors on the memory module or on the computer Debris on the connectors may cause memory access problems Figure 3 18 Removing the memory module 1 Latches 9 Seat the memory module cover in place and secure it with the screw s P Take care to ensure that the memory module cover is firmly closed 10 Install the battery pack 11 Turn your computer over External monitor An external analog monitor can be connected to the External RGB monitor port on the computer To connect a monitor follow the steps as detailed below Connecting the monitor cable 1 Connect the monitor cable to the External RGB monitor port User s Manual 3 43 Figure 3 19 Connecting the monitor cable to the External RGB monitor port 1 External RGB monitor port 2 Monitor cable 2 Turn the external monitor s power on When you turn on the power the computer will automatically recognize the monitor and determine whether it is a color or monochrome device In the event that you find that there ar
160. power on 4 8 Starting the computer by password 4 17 Supervisor 4 17 user 4 15 PC Card inserting 3 34 problems 6 10 removing 3 34 Pointing Device Touch Pad 2 11 6 10 Power conditions 5 1 Hibernation Mode 1 9 panel on off 4 8 5 10 Shut Down mode Boot Mode 1 6 Sleep Mode 1 7 System Auto Off 5 10 turning off 1 6 turning on 1 5 Problems AC power 6 5 Additional memory module 6 15 Analyzing the problem 6 2 Battery 6 5 Bluetooth 6 19 eSATA device 6 14 External monitor 6 16 Fingerprint Sensor 6 12 Hard disc drive 6 8 6 9 Hardware and system checklist 6 4 Internal display panel 6 7 Keyboard 6 7 LAN 6 18 Memory Media Card 6 9 Optical Disc Drive 6 8 Overheating power down 6 4 PC Card 6 9 Pointing device 6 10 Power 6 4 Real Time Clock 6 7 Recovery Media 6 20 Sound system 6 15 TOSHIBA support 6 20 Touch Pad 6 10 Index 3 User s Manual USB device 6 12 USB mouse 6 11 Wireless LAN 6 18 Recovery hard disk drive 4 31 Recovery Media problems 6 20 Restarting the computer 1 10 SD SDHC SDXC Card formatting 3 36 note 3 36 Security lock 3 46 Serial port 3 46 Sleep Mode setting 1 7 System automatic 4 8 Soft keys ENTER 3 4 ScrLock 3 4 Sound system problems 6 15 TOSHIBA Assist 4 4 TOSHIBA ConfigFree 4 4 TOSHIBA Disc Creator 3 20 4 4 U TOSHIBA DVD RAM Utility 4 5 TOSHIBA HDD SSD Alert Utility 4 5 TOSHIBA PC Diagnostic Tool 4 2 USB device problems 6 12 Vid
161. ption function of this software You can back up the fingerprint data or the information registered to Automatic password input in IE Please use Import Export on TOSHIBA Fingerprint Utility main menu Please also refer to the fingerprint utility Help file for more information You can start it using the following method Click Start gt All Programs gt TOSHIBA gt Tools amp Utilities gt Fingerprint Utility The main screen is displayed Click in the lower left corner of the screen Fingerprint utility limitations TOSHIBA does not guarantee that the fingerprint utility technology will be completely secure or error free or that it will accurately screen out unauthorized users at all times TOSHIBA is not liable for any failure or damage that might arise out of the use of the fingerprint software Setup Fingerprint Registration Please use the following procedure when first using fingerprint authentication User s Manual T i In use the fingerprint authentication system will use the same username and password as defined within the Windows operating system If no Windows password has been configured you must do this before starting the fingerprint registration process This sensor has the memory space for at least twenty fingerprint patterns You might be able to register more fingerprint patterns depending on the sensor memory usage Click Start gt All Programs gt TOSHIBA gt Tools amp Utilities gt
162. r impact while the function is disabled System Recovery There is a hidden partition allocated on the hard disk drive for the System Recovery Options in the event of a problem You can also create recovery media and restore the system The following items will be described in this section m System Recovery Options BR Creating Recovery Media E Restoring the pre installed software from your created Recovery Media BH Restoring the pre installed software from the Recovery hard disk drive System Recovery Options The System Recovery Options feature is installed on the hard disk when shipped from the factory The System Recovery Options menu includes tools to repair startup problems run diagnostics or restore the system See the Windows Help and Support content for more information about Startup Repair The System Recovery Options can also be run manually to repair problems The procedure is as follows Follow the instructions shown on the on screen menu 1 Turn off the computer 2 While holding the F8 key turn on the computer 3 The Advanced Boot Options menu will be displayed Use the arrow keys to select Repair Your Computer and press ENTER 4 Follow the on screen instructions a Check your Windows manual for more information on backing up your system including the system image backup feature Creating Recovery Media This section describes how to create Recovery Media User s Manual 4 28 User s Manual B
163. r programs databases and other intellectual property covered by copyright laws belongs to the author or to the copyright owner Copyrighted material can be reproduced only for personal use or use within the home Any other use beyond that stipulated above including conversion to digital format alteration transfer of copied material and distribution on a network without the permission of the copyright owner is a violation of copyright or author s rights and is subject to civil damages or criminal action Please comply with copyright laws in making any reproduction from this manual Disclaimer This manual has been validated and reviewed for accuracy The instructions and descriptions it contains are accurate for your computer at the time of this manual s production However succeeding computers and manuals are subject to change without notice TOSHIBA assumes no liability for damages incurred directly or indirectly from errors omissions or discrepancies between the computer and the manual Trademarks User s Manual Intel Intel SpeedStep Intel Core and Centrino are trademarks or registered trademarks of Intel Corporation Windows Microsoft and Windows logo are registered trademarks of Microsoft Corporation Bluetooth is a trademark owned by its proprietor and used by TOSHIBA under license Photo CD is a trademark of Eastman Kodak Company ConfigFree is a trademark of TOSHIBA Corporation TouchPad is a trademark of Synaptics I
164. ration Temporarily changing modes If the computer is in Numeric Mode you can switch temporarily to Arrow Mode by pressing a SHIFT key while if it is in Arrow Mode you can switch temporarily to Numeric Mode by also pressing a SHIFT key Generating ASCII characters User s Manual Not all ASCII characters can be generated using normal keyboard operation but you are able to generate these characters using their specific ASCII codes Full size keyboard 1 Hold down ALT key 2 Using the numeric keypad type the ASCII code of the character you require 3 Release ALT the ASCII character will appear on the display screen 3 7 A4 size keyboard 1 Hold down ALT with the overlay on or ALT FN with overlay off 2 Using the overlay keys type the ASCII code of the character you require 3 Release ALT or ALT FN the ASCII character will appear on the display screen Using the Fingerprint Sensor T This product has a fingerprint utility installed for the purpose of enrolling and recognizing fingerprints By enrolling the ID and password onto the fingerprint authentication feature it is no longer necessary to input the password from the keyboard Fingerprint feature enables you to Logon to Windows and access a security enabled homepage through Internet Explorer E Files and folders can be encrypted decrypted and third party access to them prevented BR Unlock the password protected screen saver BR Authentic
165. rd which are not on this computer s keyboard For A4 size keyboard m Press FN F10 or FN F11 to access the computer s integrated keypad When activated the keys with grey markings on their bottom edge become either numeric keypad keys FN F11 or cursor control keys FN F10 BH Press FN F12 ScrLock to lock the cursor on a specific line The power on default is off BH Press FN ENTER to simulate ENTER on the enhanced keyboard s numeric keypad Hot key functions User s Manual Hot key functions let you enable or disable certain features of the computer The Hot key functions can be performed using either the Hot Key Cards or by pressing the associated Hot keys pressing FN a function or ESC key Hot Key Cards The Hot Key Cards are normally hidden from view The Cards appear when you press the FN key To use the Hot Key Cards 1 Press and hold the FN key The TOSHIBA Flash Cards appear along the top of the screen T User s Manual 3 Select the desired option The selected Card is displayed full size with its available options below it All other Cards are again hidden from view Click the desired option To use a Hot Key Card using a hot key 1 2 Press and hold the FN key Press the hot key associated with the desired function The associated hot key card appears at the top of the screen with its available options below it To cycle through the displayed options hold down FN and pres
166. related to the Bluetooth Stack for Windows by TOSHIBA 1 Fax application software Please be aware that there is some fax application software that you cannot use on this Bluetooth Stack 2 Multi user considerations The use of Bluetooth is not supported in a multi user environment This means that when you use Bluetooth other users that are logged into the same computer will not be able to use this type of functionality Product Support The latest information regarding operating system support language support or available upgrades can be found on our web site http www toshiba europe com computers tnt bluetooth htm in Europe or www pcsupport toshiba com in the United States 3 30 LAN LAN The computer has built in support for Ethernet LAN 10 megabits per second 10BASE T Fast Ethernet LAN 100 megabits per second 100BASE TX or Gigabit Ethernet LAN 1000 megabits per second 1000BASE T This section describes how to connect disconnect to a LAN Do not install or remove a memory module while Wake up on LAN is enabled BR The Wake up on LAN function consumes power even when the system is off Leave the AC adaptor connected while using this feature BH The Link speed 10 100 1000 megabits per second changes automatically depending on the network conditions connected device cable or noise and so on cable types The computer must be configured properly before connecting to a LAN Logging onto a LAN using th
167. ricted to indoor use due to its operation in the 5 15 to 5 25GHz frequency range Taiwan Article 12 Without permission granted by the NCC any company enterprise or user is not allowed to change frequency enhance transmitting power or alter original characteristic as well as performance to an approved low power radio frequency devices Article 14 The low power radio frequency devices shall not influence aircraft security and interfere legal communications If found the user shall cease operating immediately until no interference is achieved The said legal communications means radio communications is operated in compliance with the Telecommunications Act The low power radio frequency devices must be susceptible with the interference from legal communications or ISM radio wave radiated devices Using this equipment in Japan User s Manual In Japan the frequency bandwidth of 2 400MHz to 2 483 5MHz for second generation low power data communication systems such as this equipment overlaps that of mobile object identification systems premises radio station and specified low power radio station 1 Important notice The frequency bandwidth of this equipment may operate within the same range as industrial devices scientific devices medical devices microwave ovens licensed radio stations and non licensed specified low power radio stations for mobile object identification systems RFID used in factory production lines Ot
168. ries regions in the following table Do not use this equipment in the countries regions which are not listed in the table below As of April 2012 User s Manual Austria Belgium Bulgaria Canada Cyprus Czech Rep Denmark Estonia Finland France Germany Greece Hong Kong Hungary Iceland India Indonesia Ireland Italy Japan Korea Latvia Liechtenstein Lithuania Luxemburg Malta Monaco Netherlands Norway Philippines Poland Portugal Romania Slovak Republic Slovenia Spain Sweden Switzerland UK USA User s Manual D 9 Index User s Manual AC adaptor additional 3 47 connecting 1 3 DC IN 15V jack 2 6 ASCII characters 3 7 Battery extending life 5 7 monitoring capacity 5 6 real time clock 2 12 5 4 save mode 4 8 types 5 3 Battery indicator Battery pack additional 5 1 replacing 5 8 Bluetooth Bluetooth Stack for Windows by Toshiba 4 3 problems 6 19 Boot Priority 4 19 Cleaning the computer 3 49 Cooling vents 2 3 DC IN indicator 2 2 DC IN indicator 5 3 Display automatic power off 4 7 hinges 2 10 opening 1 4 screen 2 9 Display controller 2 12 Documentation list 1 1 Dual Pointing Device Touch Pad control buttons 3 1 Equipment checklist 1 1 eSATA device problems ExpressCard inserting 3 33 removing 3 33 External monitor problems 6 16 Fingerprint Sensor problems 6 12 using 3 8 FN 1 reduce 3 6 Index 1 User s Manual FN 2 enlarge 3 6 FN ENTER 3 4 FN ESC Mute
169. rogress detect When used in the Auto Answer mode the SO register must be set with a value of 3 or 4 This ensures xiii User s Manual A person calling your modem will hear a short burst of ringing before the modem answers This confirms that the call has been successfully switched through the network Caller identification information which occurs between the first and second ring cadences is not destroyed The preferred method of dialing is to use DTMF tones ATDT as this is faster and more reliable than pulse decadic dialing If for some reason you must use decadic dialing your communications program must be set up to record numbers using the following translation table as this modem does not implement the New Zealand Reverse Dialing standard Number to be dialed 0123456789 Number to program into computer 098765432 1 Note that where DTMF dialing is used the numbers should be entered normally The transmit level from this device is set at a fixed level and because of this there may be circumstances where the performance is less than optimal Before reporting such occurrences as faults please check the line with a standard Telepermitted telephone and only report a fault if the phone performance is impaired It is recommended that this equipment be disconnected from the Telecom line during electrical storms When relocating the equipment always disconnect the Telecom line connection before the power connection
170. s can be specified in the Power Options This feature automatically turns power to the computer off when the display panel is closed and turns it back on when the display panel is opened This can be specified in the Power Options When battery power is exhausted to the point that computer operation cannot be continued the system automatically enters Hibernation Mode and shuts itself down This can be specified in the Power Options To protect against overheating the processor has an internal temperature sensor so that if the computer s internal temperature rises to a certain level the cooling fan is turned on or the processing speed is lowered This can be specified in the Power Options TOSHIBA HDD This feature uses the acceleration sensor built in Protection the computer to detect vibration and shocks and automatically moves the hard disk drive s read write head to a safe position in order to reduce the risk of damage that could be caused by head to disk contact Refer to the Using the Hard Disk Drive HDD Protection section for more details Hibernation Mode This feature lets you turn off the power to the computer without exiting from your software The contents of main memory are automatically saved to the hard disk drive so that when you next turn the power on again you can continue working right where you left off Refer to the Turning off the power section in Chapter 1 Getting Started for more details Sleep Mo
171. s device must accept any interference including interference that may cause undesired operation of this device The term IC before the equipment certification number only signifies that the Industry Canada technical specifications were met USA Federal Communications Commission FCC This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation Refer to the FCC information section for the detailed information Caution Exposure to Radio Frequency Radiation The radiated output power of the Wireless device is far below the FCC radio frequency exposure limits Nevertheless the Wireless device shall be used in such a manner that the potential for human contact during normal operation is minimized In the usual operating configuration the distance between the antenna and the user should not be less than 20cm Please refer to the computer user s manual for the details regarding antenna location The installer of this radio equipment must ensure that the antenna is located or pointed such that it does not emit RF field in excess of Health Canada limits for the general population consult Safety Code 6 obtainable from Health Canada s website www hc sc gc ca Caution Radio Frequency Interference Requirements User s Manual This device is rest
172. s local networks on board aircraft during a flight at the altitude not less than 3000m Restrictions for Use of 5470 5725MHz Frequencies in Europe Italy Luxembourg Implemented Russian Limited Federation For private use a general authorization is required if WAS RLAN s are used outside own premises General authorization required for network and service supply e i r p 100mW Permitted to use only for indoor applications closed industrial and warehouse areas and on board aircraft 1 Permitted to use for local networks of aircraft crew service communications on board aircraft in area of the airport and at all stages of flight 2 Permitted to use for public wireless access local networks on board aircraft during a flight at the altitude not less than 3000m To remain in conformance with European spectrum usage laws for Wireless LAN operation the above 2 4GHz and 5GHz channel limitations apply for outdoor usage The user should use the wireless LAN utility to User s Manual check the current channel of operation If operation is occurring outside of the allowable frequencies for outdoor use as listed above the user must contact the applicable national spectrum regulator to request a license for outdoor operation Canada Industry Canada IC This device complies with RSS 210 of Industry Canada Operation is subject to the following two conditions 1 this device may not cause interference and 2 thi
173. s product may be purchased from the retailer As the port operation has not been confirmed some monitors may not function properly eSATA External Serial ATA device An device corresponding to eSATA function can be connected to the eSATA USB combo port on the computer Connecting the eSATA device To connect an eSATA device follow the steps as detailed below 1 Connect an eSATA cable to the eSATA USB combo port AN Make sure the connector is properly aligned with the socket Do not try to force the connection doing so can damage the connecting pins Figure 3 21 Connecting an eSATA cable to the eSATA USB combo port 1 eSATA USB combo port 2 eSATA cable T User s Manual A connected eSATA device may not be recognized if it is connected to the computer s eSATA USB combo port while the computer is in Sleep Mode or Hibernation Mode If this occurs disconnect the eSATA device and then reconnect the device while the computer is turned on If you connect an eSATA device after the computer has already been turned on it will take about ten seconds for it to be recognized by the computer Do not attempt to disconnect and reconnect the drive before this period has elapsed 3 45 Disconnecting an eSATA device When you have finished using an eSATA device you can follow the procedures below in order to disconnect it 1 Wait for the indicator light of an eSATA device to go out to make sure all activity has stopped
174. s the hot key repeatedly Release the FN key when the desired option is selected For more information please refer to the TOSHIBA Flash Cards Help file To access this help click Start gt All Programs gt TOSHIBA gt Tools amp Utilities gt Flash Cards In the Settings for Flash Cards window click the Help button Hot keys This section describes the associated functions of the hot keys E Mute Pressing FN ESC turns the volume on and off E Lock Pressing FN F1 enters Lock computer mode To restore your desktop you need to log on again E Power Plan Pressing FN F2 changes the power settings E Sleep Pressing FN F3 switches the system to Sleep Mode m Hibernate Pressing FN F4 switches the system to Hibernation Mode E Output Pressing FN F5 changes the active display device To use a simultaneous mode you must set the resolution of the internal display panel to match the resolution of the external display device Brightness Down Pressing FN F6 decreases the computer s display panel brightness in individual steps Brightness Up Pressing FN F7 increases the computer s display panel brightness in individual steps Wireless Pressing FN F8 switches the active wireless devices If no wireless communication device is installed no dialog box will appear Touch Pad Pressing FN F9 enables or disables the Touch Pad function BH Zoom Display resolution Pressing FN Space changes the displ
175. safety standards User s Manual D 2 Europe Restrictions for Use of 2400 0 2483 5MHz Frequencies in Europe France Italy Luxembourg Norway Russian Federation Outdoor use limited to 10mW e i r p within the band 2454 2483 5MHz Implemented Implemented Military Radiolocation use Refarming of the 2 4GHz band has been ongoing in recent years to allow current relaxed regulation Full implementation planned 2012 For private use a general authorization is required if WAS RLAN s are used outside own premises For public use a general authorization is required General authorization required for network and service supply This subsection does not apply for the geographical area within a radius of 20 km from the centre of Ny Alesund Only for indoor applications Restrictions for Use of 5150 5350MHz Frequencies in Europe Italy Luxembourg User s Manual Implemented For private use a general authorization is required if WAS RLAN s are used outside own premises General authorization required for network and service supply Russian Limited Federation e i r p 100mW Permitted to use only for indoor applications closed industrial and warehouse areas and on board aircraft 1 Permitted to use for local networks of aircraft crew service communications on board aircraft in area of the airport and at all stages of flight 2 Permitted to use for public wireless acces
176. se Tone Control command AT commands EIA 578 commands Monitor function Computers Speaker Communication specifications Communication system Data Communication protocol User s Manual Fax Data ITU T Rec Former CCITT Bell Fax ITU T Rec Former CCITT Full duplex Half duplex V 21N 22 V 22bis V 32 V 32bis V 34 V 90 103 212A V 17N 29 V 27ter V 21 ch2 User s Manual Network control unit NCU Communication speed Transmitting level Receiving level Input output impedance Error correcting Data compression Power supply Data transmission and reception 300 1200 2400 4800 7200 9600 12000 14400 16800 19200 21600 24000 26400 28800 312 00 336003223 3233 and 3220 bps Data reception only with V 90 28000 29333 30666 32000 33333 34666 360 00 37333 38666 40000 41333 42666 44000 4 5333 46666 48000 49333 50666 52000 5333 3 54666 560003223 3233 and 3220 bps Fax 2400 4800 7200 9600 12000 14400 bps 10 dBm 10 to 40 dBm 600 ohms 30 MNP class 4 and ITU T V 42 MNP class 5 and ITU T V 42bis 3 3V supplied by computer Appendix B AC Power Cord and Connectors The power cord s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country region in which it is used All cords must meet the following specifications Wire size Minimum 0 75 mm Current rating Minimum 2 5 amperes Certification agencies
177. se harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures BH Reorient or relocate the receiving antenna BH Increase the separation between the equipment and receiver BH Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Only peripherals complying with the FCC class B limits may be attached to this equipment Operation with non compliant peripherals or peripherals not recommended by TOSHIBA is likely to result in interference to radio and TV reception Shielded cables must be used between the external devices and the computer s External RGB monitor port Universal Serial Bus USB 2 0 and 3 0 ports eSATA USB combo port Mini DisplayPort serial port and microphone jack Changes or modifications made to this equipment not expressly approved by TOSHIBA or parties authorized by TOSHIBA could void the user s authority to operate the equipment FCC conditions This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation Contact Address TOSHIBA Am
178. security lock In order to connect a security cable to the computer follow the steps as detailed below 1 Turn the computer so its back side faces you 2 Align the security cable with the lock slot and secure it in place Figure 3 23 Security lock 1 Security lock slot 2 Security lock Optional TOSHIBA Accessories You are able to add a number of options and accessories in order to make your computer even more powerful and convenient to use For reference the following list details some of the items that are available from your reseller or TOSHIBA dealer Memory Kit DDR3 1600 memory modules can easily be installed in the computer The available option memory depends on TOSHIBA authorization Universal AC Adaptor If you frequently use your computer at more than one site it may be convenient to purchase an additional AC adaptor to be kept at each site in order to remove the need to always carry the adaptor with you Battery Pack An additional battery pack can be purchased for use as either a spare or replacement Please refer to Chapter 5 Power and Power Up Modes for further information Sound System This section describes some of the audio control functions User s Manual 3 47 Volume Mixer The Volume Mixer utility lets you control the audio volume for playback of devices and applications under Windows BR To launch the Volume Mixer utility right click on the speaker icon on the Taskbar and select Open Vol
179. sed to drive displays with a HDMI or DVI interface Some models are equipped with a Mini DisplayPort This slot allows you to install a single ExpressCard device This slot can accommodate a single Type Il 16 bit or 32 bit CardBus PC Card device This button is used in order to remove a PC Card from within the computer Figure 2 3 The right side of the computer GO 1 Headphone jack 2 Microphone jack 4 Universal Serial Bus USB 2 0 port 5 Optical disc drive 3 Universal Serial Bus USB 2 0 port Provided with some models Product appearance depends on the model you purchased Headphone jack Microphone jack Universal Serial Bus USB 2 0 ports Optical disc drive A 3 5 mm mini headphone jack enables connection of stereo headphones A 3 5 mm mini microphone jack enables connection of a three conductor mini jack for monaural microphone input Two Universal Serial Bus ports which comply to the USB 2 0 standard are provided on the right side of the computer The computer may be configured with an optical disc drive T A 2 6GB and 5 2GB DVD RAM media cannot be read from or written to Please note that it is not possible to confirm the operation of all functions of all USB devices that are available In view of this it may be noted that some functions associated with a specific device might not operate properly USB 3 0 port s may work as USB 2 0 port s when operating in
180. ser s Manual You should always consider the simplest solution first the items detailed in this checklist are easy to fix and yet can cause what appears to be a serious problem RB Make sure you turn on all peripheral devices before you turn on the computer this includes your printer and any other external device you are using BH Before you attach an external device you should first turn the computer off then when you turn the computer back on again it will recognize the new device m Make sure all optional accessories are configured properly in the computer s setup program and that all required driver software has been loaded please refer to the documentation included with the optional accessories for further information on its installation and configuration Check all cables to ensure they are correctly and firmly attached to the computer loose cables can cause signal errors Inspect all connecting cables for loose wires and all connectors for loose pins Check that your disc media is correctly loaded Always try to make detailed notes of your observations and keep them ina permanent error log this will help you to describe your problems to TOSHIBA Support In addition if a problem recurs the log you have made will help to identify the problem faster Analyzing the problem User s Manual Sometimes the computer will give you clues that can help you identify why it is malfunctioning In view of this you should keep the
181. sign and configuration client design and software hardware configurations The transmission rate described is the theoretical maximum speed as specified under the appropriate standard the actual transmission speed will be lower than the theoretical maximum speed Setting 1 Please make sure that the Wireless Communication function is on 2 Click Start gt Control Panel gt Network and Internet gt Network and Sharing Center 3 Click Set up a new connection or network 4 Follow the wizard You will need the name of the wireless network together with security settings Consult the documentation accompanied with your router or ask your wireless network administrator for the settings Security BR TOSHIBA strongly recommend that you enable encryption functionality otherwise your computer will be open to illegal access by an outsider using a wireless connection If this occurs the outsider may illegally access your system eavesdrop or cause the loss or destruction of stored data RH TOSHIBA is not liable for the loss of data due to eavesdropping or illegal access through the wireless LAN and the damage thereof Card Specifications Form Factor PCI Express Mini Card 3 28 Compatibility m IEEE 802 11 Standard for Wireless LANs BR Wi Fi Wireless Fidelity certified by the Wi Fi Alliance The Wi Fi CERTIFIED logo is a certification mark of the Wi Fi Alliance Network Operating BR Microsoft Windows Networking System
182. so may reduce image quality Use an eyeglass cleaner cleaner cloth or other soft cloth to clean the lens if it becomes dirty E When recording in dimly lit environments select Night Mode which allows for brighter images with less noise Display screen 39 6cm 15 6 LCD screen 16 million colors configured with the following resolution m HD 1600 horizontal x 900 vertical pixels m HD 1366 horizontal x 768 vertical pixels Please be aware that when the computer is operating on the AC adaptor the image displayed on the internal screen will be somewhat brighter than when it operates on battery power This difference in brightness levels is intended to save power when operating on batteries Legal Footnote LCD For more information regarding LCD please refer to the Legal Footnotes section in Appendix C User s Manual 2 9 T el H User s Manual LCD Sensor switch This switch senses when the display panel is either closed or opened and activates the Panel Power Off On feature as appropriate For example when you close the display panel the computer enters Hibernation Mode and shuts itself down and then when you next open the display the computer will automatically start up and return you to the application you were previously working on You can specify within the Power Options To access it click Start gt Control Panel gt System and Security gt Power Options Do not put any magnetic objects cl
183. splay automatic power off function to run while the TOSHIBA VIDEO PLAYER is running 3 22 Do not switch to Hibernation or Sleep Mode when running the TOSHIBA VIDEO PLAYER Do not lock the computer using the Windows logo s L keys when running the TOSHIBA VIDEO PLAYER The TOSHIBA VIDEO PLAYER does not have a parental control function In order to protect copyrights the Windows Print Screen function is disabled when TOSHIBA VIDEO PLAYER is running Print Screen functions are disabled even when running other applications besides TOSHIBA VIDEO PLAYER and when TOSHIBA VIDEO PLAYER is minimized Please close the TOSHIBA VIDEO PLAYER to use the Print Screen function Carry out the installation uninstallation of the TOSHIBA VIDEO PLAYER under a user account with administrator rights Do not change Windows Users while TOSHIBA VIDEO PLAYER is running For some DVD Video discs using the control window to change the audio track will also change the subtitle track This software can playback MPEG2 MP4 and WTV files created by Corel Digital Studio for TOSHIBA Playback may not function properly if you use the files other than these types Display Devices amp Audio TOSHIBA VIDEO PLAYER will only run when Colors is set to True Color 32 bit Click Start gt Control Panel gt Appearance and Personalization gt Display gt Adjust resolution click Advanced settings select Monitor tab set colors to True color 32
184. ss LAN User s Manual The transmission speed over the wireless LAN and the distance over which wireless LAN can reach may vary depending on surrounding electromagnetic environment obstacles access point design and configuration and client design and software hardware configurations The actual transmission speed will be lower than the theoretical maximum speed Copy Protection Applicable copy protection standards included in certain media may prevent or limit recording or viewing of the media User s Manual Appendix D Information for Wireless Devices Wireless LAN Interoperability The Wireless LAN is compatible with other LAN systems Direct Sequence Spread Spectrum DSSS Orthogonal Frequency Division Multiplexing OFDM radio technology and is compliant to E The IEEE 802 11 Standard on Wireless LANs Revision a b g n or b g n as defined and approved by the Institute of Electrical and Electronics Engineers BR The Wireless Fidelity Wi Fi certification as defined by the Wi Fi Alliance The Wi Fi CERTIFIED logo is a certification mark of the Wi Fi Alliance Bluetooth wireless technology Interoperability T Bluetooth Cards are designed to be interoperable with the product with Bluetooth wireless technology that is based on Frequency Hopping Spread Spectrum FHSS radio technology and is compliant to E Bluetooth Specification depending on the model you purchased as defined and approved by the Blu
185. stem PC plus options cables still fulfils the required standards To avoid general EMC problems the following guidance should be noted BR Only CE marked options should be connected implemented m Only best shielded cables should be connected Working environment This product was designed to fulfil the EMC Electromagnetic Compatibility requirements to be observed for so called Residential commercial and light industry environments TOSHIBA do not approve the use of this product in working environments other than the above mentioned Residential commercial and light industry environments For example the following environments are not approved vi E Industrial Environments e g environments where a mains voltage of 380 V three phase is used Medical Environments E Automotive Environments E Aircraft Environments Any consequences resulting from the use of this product in working environments that are not approved are not the responsibility of TOSHIBA The consequences of the use of this product in non approved working environments may be BH Interference with other devices or machines in the near surrounding area BR Malfunction of or data loss from this product caused by disturbances generated by other devices or machines in the near surrounding area Therefore TOSHIBA strongly recommend that the electromagnetic compatibility of this product should be suitably tested in all non approved working enviro
186. substances in electrical and electronic equipment The number of possible pixel failures of your display is defined according to ISO 9241 307 standards If the number of pixel failures is less than this standard they will not be counted as defect or failure Battery is a consumption product since the battery time depends on the usage of your computer If the battery can not be charged at all then it is a defect or failure The changes in battery time is not a defect or failure ENERGY STAR Program User s Manual Ban Your Computer model may be ENERGY STAR ad compliant If the model you purchased is compliant it is labeled with the ENERGY STAR logo on the computer and the following information applies TOSHIBA is a partner in the ENERGY STAR Program and has designed this computer to meet the latest ENERGY STAR guidelines for energy efficiency Your computer ships with the power management options preset to a configuration that will provide the most stable operating environment and optimum system performance for both AC power and battery modes To conserve energy your computer is set to enter the low power Sleep Mode which shuts down the system and display within 15 minutes of inactivity in AC power mode TOSHIBA recommends that you leave this and other energy saving features active so that your computer will operate at its maximum energy efficiency You can wake the computer from Sleep Mode by pressing the power button
187. t the telephone company will give you notice in writing to allow you to make any changes necessary to maintain uninterrupted service If problems arise If any of your telephone equipment is not operating properly you should immediately remove it from your telephone line as it may cause harm to the telephone network If the telephone company notes a problem they may temporarily discontinue service When practical they will notify you in advance of this disconnection If advance notice is not feasible you will be notified as soon as possible When you are notified you will be given the opportunity to correct the problem and informed of your right to file a complaint with the FCC In the event repairs are ever needed on your modem they should be performed by TOSHIBA Corporation or an authorized representative of TOSHIBA Corporation Disconnection If you should ever decide to permanently disconnect your modem from its present line please call the telephone company and let them know of this change Fax branding The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device to send any message via a telephone fax machine unless such message Clearly contains in a margin at the top or bottom of each transmitted page or on the first page of the transmission the date and time it is sent and an identification of the business other entity or individual sending the message and the t
188. t 68 When you are ready to install or use the modem call your local telephone company and give them the following information User s Manual ix User s Manual E The telephone number of the line to which you will connect the modem BH The registration number that is located on the device The FCC registration number of the modem will be found on either the device which is to be installed or if already installed on the bottom of the computer outside of the main system label m The Ringer Equivalence Number REN of the modem which can vary For the REN of your modem refer to your modem s label The modem connects to the telephone line by means of a standard jack called the USOC RJ11C Type of service Your modem is designed to be used on standard device telephone lines Connection to telephone company provided coin service central office implemented systems is prohibited Connection to party lines service is subject to state tariffs If you have any questions about your telephone line such as how many pieces of equipment you can connect to it the telephone company will provide this information upon request Telephone company procedures The goal of the telephone company is to provide you with the best service it can In order to do this it may occasionally be necessary for them to make changes in their equipment operations or procedures If these changes might affect your service or the operation of your equipmen
189. t and right hand edges the edges with the grooves in User s Manual 3 41 8 Seat the memory module cover in place and secure it with the screw s T Take care to ensure that the memory module cover is firmly closed 10 11 Figure 3 17 Seating the memory module cover 1 Memory module cover 2 Screw Install the battery pack refer to Replacing the battery pack section in Chapter 5 Power and Power Up Modes if required Turn your computer over Turn the computer on and make sure the added memory is recognized to confirmed it Start gt Control Panel gt System and Security gt System icon Removing a memory module To remove the memory module follow the steps as detailed below 1 B E User s Manual Shut down the computer make sure the Power indicator is off refer to the Turning off the power section in Chapter 1 Getting Started if required Remove the AC adaptor and all cables and peripherals connected to the computer Close the display panel Turn the computer upside down and remove the battery pack Loosen the screw s securing the memory module cover in place please note that the screws are attached to the cover in order to prevent them from being lost Slide your fingernail or a thin object under the cover and lift it off Push the latches away from the module in order to release it a spring will force one end of the module u
190. tained between the computer and a mobile phone that is in use Instruction Manual for Safety and Comfort All important information on the safe and proper use of this computer is described in the enclosed Instruction Manual for Safety and Comfort Be sure to read it before using the computer User s Manual xxiii Chapter 1 Getting Started A This chapter provides an equipment checklist and basic information to start using your computer Some of the features described in this manual may not function properly if you use an operating system that was not pre installed by TOSHIBA Equipment checklist Carefully unpack your computer taking care to save the box and packaging materials for future use Hardware Check to make sure you have all the following items H TOSHIBA Portable Personal Computer BR AC adaptor and power cord 2 pin plug or 3 pin plug RH Battery pack Is preinstalled in some computers Documentation BR User Information Guide BR Instruction Manual for Safety and Comfort If any of the items are missing or damaged contact your dealer immediately Software User s Manual The following Windows operating system and utility software are pre installed Windows 7 TOSHIBA Recovery Media Creator TOSHIBA Assist TOSHIBA ConfigFree TOSHIBA Flash Cards TOSHIBA Disc Creator TOSHIBA Resolution Plug in For Windows Media Player TOSHIBA eco Utility TOSHIBA Bulletin Board 1 1 i TOSHIBA Re
191. ter Check with your LAN administrator and hardware or software vendor before using or configuring a network connection Optional devices Optional devices can expand the computer s capabilities and its versatility This section describes the connection or installation of the following devices Cards memory H ExpressCard PC Card E Memory media BR Additional memory module Peripheral devices E External monitor E Serial port BR Mini DisplayPort E eSATA device Other BH Security lock Optional TOSHIBA accessories ExpressCard Some models are equipped with a single ExpressCard slot into which any ExpressCard device that meets industry standards either manufactured by TOSHIBA or another vendor can be installed The slot supports hot plug User s Manual 3 32 connection and utilizes the PCI Express interface that supports the reading and writing of data at a theoretical maximum rate of 2 5Gbps Inserting an ExpressCard The Windows hot install feature allows you to insert ExpressCards while the computer is turned on Do not insert an ExpressCard while the computer is in Sleep Mode or J Hibernation Mode as you may find that some cards do not work properly To insert an ExpressCard follow the steps as detailed below 1 Press the Dummy card in order to eject the Dummy card partially out of the computer Grasp the Dummy card and draw it Insert the ExpressCard into the ExpressCard slot on the left side of the c
192. ter in this way could allow the operating system to reactivate and run pre programmed tasks or preserve unsaved data which could interfere with aviation or other systems possibly causing serious injury Before entering Sleep Mode be sure to save your data BR Do not install or remove a memory module while the computer is in Sleep Mode The computer or the memory module could be damaged BR Do not remove the battery pack while the computer is in Sleep Mode unless the computer is connected to an AC power source Data in memory could be lost BR Do not switch to Sleep Mode while transferring data to external media such as USB devices memory media or other external memory devices Data will be lost m When the AC adaptor is connected the computer will go into Sleep Mode according to the settings in the Power Options to access it Start gt Control Panel gt System and Security gt Power Options BR 7o restore the operation of the computer from Sleep Mode press and hold the power button or any key on the keyboard for a short amount of time Please note that keyboard keys can only be used if the Wake up on Keyboard option is enabled within the HWSetup utility m If the computer enters Sleep Mode while a network application is active the application might not be restored when the computer is next turned on and the system returns from Sleep Mode To prevent the computer from automatically entering Sleep Mode disable Sle
193. tery condition go to Step 4 4 Connect the AC adaptor to the DC IN 15V jack of the computer and to a wall outlet that is supplying power The DC IN indicator should glow green and the Battery indicator should glow orange to indicate that the battery pack is being charged however in the event that DC IN indicator does not glow this indicates that power is not being supplied check the connections for the AC adaptor and the power cord 5 Charge the battery pack until the Battery indicator glows green If you have extra battery packs rotate their use BH f you will not be using the system for an extended period for example for more than one month remove the battery pack from the computer BH Store spare battery packs in a cool dry place out of direct sunlight Replacing the battery pack Please be aware that the battery pack is classified as a consumable item The operating life of the battery pack will gradually reduce through repeated charging and discharging and will need to be replaced when it reaches the end of its operating life In addition to this you might also replace a discharged battery pack with a charged spare when you are operating your computer away from an AC power source for an extended period of time This section explains how to remove and install the battery pack and begins with the removal process which is detailed through the following steps m Do not remove the battery pack while the computer is in S
194. the HDD Master Password 7 To start BIOS Setup Press and hold the F2 key and then turn on the d computer the BIOS setup utility will load To end the BIOS Setup Press F10 and then press Y to accept the changes The computer will restart User s Manual Change button Click this button to change a registered password Before you can change a password you must first enter the current password correctly Please use BIOS Setup to change or delete the HDD Passwords or to set the HDD Master Password Owner String text box You can use this box to associate text with the password After you enter text click Apply or OK When the computer is started this text will be displayed together with the prompt asking you to enter a password If you forget your HDD User Password TOSHIBA will NOT be able to assist you and your HDD will be rendered COMPLETELY and PERMANENTLY INOPERABLE TOSHIBA will NOT be held responsible for any loss of any data any loss of use or access to your HDD or for any other losses to you or any other person or organization that result from the loss of access to your HDD If you can t accept this risk don t register the HDD User Password m When saving the HDD User Password shut down or restart the computer If the computer is not shut down or restarted the saved data may not be correctly reflected For more information on shutting down or restarting the computer refer to Turning on the power in Chapter 1
195. the computer with the display panel open 1 Wireless communication antennas 9 TOSHIBA Presentation button not shown 2 Web Camera LED 10 Volume down button 3 Web Camera 11 Volume up button 4 Display screen 12 Keyboard 5 LCD Sensor switch not shown 13 Touch Pad 6 Display hinges 14 Touch Pad control buttons 7 Power button 15 Fingerprint Sensor 8 TOSHIBA eco button Provided with some models Product appearance depends on the model you purchased Wireless Some computers in this series are equipped with communication the Wireless LAN Bluetooth antennas antennas Legal Footnote Wireless LAN For more information regarding Wireless LAN please refer to the Legal Footnotes section in Appendix C User s Manual 2 8 Web Camera LED The Web Camera LED glows when the Web Camera is operating Web Camera Web Camera is a device that allows you to record video or take photographs with your computer You can use it for video chatting or video conferences using a communication tool such as Windows Live Messenger TOSHIBA Web Camera Application will help you to add various video effects to your video or photograph Enables the transmission of video and use of video chat via the internet using specialized applications Please refer to the Web Camera Application Online Help for details ie BR Do not point the web camera directly at the sun d Do not touch or press strongly on the web camera lens Doing
196. the internal real time clock and calendar function and also maintains the system configuration while the computer is turned off If the RTC battery becomes completely discharged the system will lose this information and the real time clock and calendar will stop working You can change the Real Time Clock settings in the BIOS setup utility To access it press and hold the F2 key and then turn on the computer the BIOS setup utility will load Please refer to Chapter 6 Troubleshooting for further information The RTC battery does not charge while the computer is turned off even if the AC adaptor is attached Care and use of the battery pack A User s Manual This section provides the important safety precautions in order to handle your battery pack properly Refer to the enclosed Instruction Manual for Safety and Comfort for detailed precautions and handling instructions E Make sure the battery is securely installed in the computer before attempting to charge the battery pack Improper installation could generate smoke or fire or cause the battery pack to rupture m Keep the battery pack out of reach of infants and children It can cause injury D The lithium ion battery pack can explode if not replaced used handled or disposed of properly Dispose of the battery as required by local ordinances or regulations Use only batteries recommended by TOSHIBA as replacements The computer s RTC battery is a Ni MH battery
197. tically cuts off power to the off hard disk drive when it is not accessed for a specified time with power being restored when the hard disk drive is next accessed This can be specified in the Power Options User s Manual System automatic Sleep Hibernation Mode Keypad overlay Power on password Instant security Intelligent power supply Battery save mode Panel power on off Low battery automatic Hibernation Mode Heat dispersal This feature automatically shuts down the system into either Sleep Mode or Hibernation Mode when there is no input or hardware access for a specified time This can be specified in the Power Options A ten key numeric keypad is integrated into the A4 size keyboard Please refer to the Keypad overlay for A4 size keyboard section in Chapter 3 Operating Basics for information on using this feature Two levels of password security supervisor and user are available to prevent unauthorized access to your computer A specific hot key function automatically locks the system providing data security A microprocessor in the computer s intelligent power supply detects the battery s charge automatically calculates the remaining battery capacity and protects electronic components from abnormal conditions such as a voltage overload from the AC adaptor This can be specified in the Power Options This feature lets you configure the computer in order to save battery power Thi
198. tion This feature automatically turns off the system in Sleep or Hibernation Mode if the computer is not used for a set duration Refer to Special features in Chapter 4 for an explanation of how to set the duration User s Manual Chapter 6 Troubleshooting TOSHIBA have designed this computer for durability however should problems occur you are able to use the procedures detailed in this chapter to help determine the cause All users should become familiar with this chapter as knowing what might go wrong can help prevent problems from occurring in the first place Problem solving process Resolving problems will be much easier if you observe the following guidelines H Stop immediately when you recognize a problem exists as taking further action may result in data loss or damage or you may destroy valuable problem related information that can help solve the problem m Observe what is happening write down what the system is doing and what actions you performed immediately before the problem occurred Make a screenshot of the current display Please also be aware that the questions and procedures described in this chapter are meant only as a guide they are not definitive problem solving techniques In reality many problems can be solved simply but a few may require help from TOSHIBA Support if you find you need to consult others be prepared to describe the problem in as much detail as possible Preliminary checklist U
199. ts that support the Sleep and Charge function In that case use an USB port that does not have the USB Sleep and Charge function compatible icon 4 or change to disable both System ON CDP Charge Mode and USB Sleep and Charge function eSATA device In addition to the information in this section please also refer to the documentation supplied with your eSATA device User s Manual 6 14 Problem Procedure eSATA device does Remove the eSATA device from the computer and not work then reconnect it to a free port it in order to ensure it is firmly attached A connected eSATA device may not be recognized if it is connected to the computer s eSATA USB combo port while the computer is in Sleep Mode or Hibernation Mode If this occurs disconnect the eSATA device and then reconnect the device while the computer is turned on Ensure that any required eSATA device drivers are properly installed to achieve this you should refer to both the device documentation and the operating system documentation If you are still unable to resolve the problem contact TOSHIBA Support Additional memory module Please also refer to Chapter 3 Operating Basics for further information on installing and removing memory modules Problem Procedure An error will occur if Remove the memory module from Slot B and a memory module is insert it into Slot A inserted into Slot B while no memory module is inserted in Slot A Sound system
200. ty 1 To access this utility click Start gt Control Panel gt Hardware and Sound gt Mouse 2 Within the Mouse Properties window click the Pointer Options tab 3 Set the pointer speed as required and click OK Problem The on screen pointer moves erratically Fingerprint Sensor Problem Reading of the fingerprint was not successful The fingerprint cannot be read due to injuries to the finger USB device Procedure The elements of the mouse responsible for detecting movement might be dirty please refer to the documentation supplied with the mouse for instructions on how to clean it If you are still unable to resolve the problem contact TOSHIBA Support Procedure In this instance you should try the fingerprint reading operation again using the correct finger position please refer to Using the Fingerprint Sensor in Chapter 3 Operating Basics for further information Alternatively you should try the recognition process again using another enrolled finger The fingerprint sensor compares and analyzes the unique characteristics in a fingerprint However there may be instances where certain users are unable to register their fingerprints due to insufficient unique characteristics in their fingerprints The recognition success rate may differ from user to user In this instance you should try the recognition process again using another enrolled finger However if fingerprints from all t
201. ume Mixer from the sub menu BH To adjust the volume level of speakers or headphones move the Speakers slider BH To adjust the volume level of an application that you are using move the slider for the corresponding application Microphone Level Follow the steps below to change the microphone recording level 1 Right click on the speaker icon on the Taskbar and select Recording devices from the sub menu 2 Select Microphone and click Properties 3 On the Levels tab move the Microphone slider to increase or decrease the microphone volume level If you feel the microphone volume level is inadequate move the Microphone Boost slider to a higher level Audio Enhancements In order to apply the sound effects for your current speaker follow the steps below 1 Right click on the Speakers icon on the Taskbar and select Playback devices from the sub menu 2 Select Speakers and click Properties 3 On the Enhancements tab select the sound effects you would like and click Apply Realtek HD Audio Manager User s Manual You can confirm and change the audio configuration using the Realtek HD Audio Manager To launch the Realtek HD Audio Manager click Start gt Control Panel select Large icons from View by then click Realtek HD Audio Manager When you first launch the Realtek HD Audio Manager you will see two device tabs Speakers is the default output device Microphone is the default input device To change the defau
202. urity enabled homepage through Internet Explorer m Files and folders can be encrypted decrypted and third party access to them is prevented BR Unlock the password protected screen saver BR Authentication of the User Password and if applicable the HDD Hard Disk Drive Password when booting up the computer Power on Security RH Single Sign on feature Fingerprint security cannot be used in models that do not have a fingerprint module installed TOSHIBA Face Recognition uses a face verification library to verify the face data of users when they log in to Windows If the verification is successful the user will be logged into Windows automatically The user can thus avoid having to enter a password or the like which makes the login process easier For more information please refer to the Using the TOSHIBA Face Recognition section This software is provided for playback of Video It has an on screen interface and functions Click Start gt All Programs gt TOSHIBA gt Media amp Entertainment gt TOSHIBA VIDEO PLAYER For details on how to use TOSHIBA VIDEO PLAYER see the help file This software enables communication between the computer and external Bluetooth devices such as printers and mobile phones Bluetooth functions cannot be used in models that do not have a Bluetooth module installed User s Manual TOSHIBA Assist TOSHIBA ConfigFree TOSHIBA eco Utility TOSHIBA Disc Creator TOS
203. us on the logon screen You can quickly check the current Wireless LAN connection status before logging into Windows To change the settings of this utility click Start gt All Programs gt TOSHIBA gt Network amp Connectivity gt Wireless LAN Indicator Settings This application allows you to control your music pictures and videos by streaming content to any compatible device in your home To access this utility click Start gt All Programs gt TOSHIBA gt Media amp Entertainment gt TOSHIBA Media Controller For more information please refer to the TOSHIBA Media Controller Help The plug in lets you upconverts wmv and mp4 videos on Windows Media Player For more information please refer to the TOSHIBA Resolution Plug in for Windows Media Player Help To access it click Start gt All Programs gt TOSHIBA gt Media amp Entertainment gt TOSHIBA Resolution Plug in for Windows Media Player Help The TPM Trusted Platform Module is a security encryption device for the hard disk drive BIOS setup and Infineon TPM Software Professional Package must be installed and configured in order to use TPM To enable TPM through the BIOS setup 1 Press and hold the F2 key and then turn on the computer the BIOS setup utility will load i 2 Set the TPM in the Security tab to Enabled 3 Press the F10 key 4 Press the Y key to accept the changes The computer will restart In order to c
204. ut or cursor and page control User s Manual Arrow Mode To turn on Arrow Mode press FN F10 the Arrow Mode indicator lights and you are able to access cursor and page control functions by using the keys You are able to press FN F10 again to turn off this overlay function Numeric Mode To turn on Numeric Mode press FN F11 the Numeric Mode indicator lights and you are able to access numeric characters by using the keys You are able to press FN F11 again to turn off this overlay function Temporarily using normal keyboard overlay on While using the overlay you can temporarily access the normal keyboard functions without having to turn the overlay off 1 Hold down FN key and press any other key this key will operate as if the overlay were off 2 Type upper case characters by holding down FN SHIFT and pressing a character key 3 Release FN key to continue using the selected overlay function Temporarily using overlay overlay off While using the normal keyboard function you can temporarily use the keypad overlay without having to turn it on 1 Hold down FN key 2 Check the keyboard indicators as pressing the FN key will turn on the most recently used overlay function if the Numeric Mode indicator lights you can use the overlay for numeric entry while if the Arrow Mode indicator lights you can use the overlay for cursor and page control function 3 Release FN key to return to normal keyboard ope
205. window To open the window click Start gt All Programs gt TOSHIBA gt Tools amp Utilities gt HDD Protection The window can also be started from the icon on the Taskbar or from the Control Panel HDD Protection You can choose whether to enable or disable TOSHIBA HDD Protection User s Manual 4 26 Detection Level This function can be set to four levels The sensitivity levels in which vibrations impacts and their similar signs are detected can be set to OFF 1 2 and 3 in ascending order Level 3 is recommended for better protection of the computer However when the computer is used in a mobile environment or in other unstable conditions setting the detection level to 3 could result in frequent execution of TOSHIBA HDD Protection which will slow Hard Disk Drive reading and writing Set a lower detection level when the speed of Hard Disk Drive reading and writing is a priority Different detection levels can be set depending on whether the computer is used as handheld or mobile usages or whether it is used in a stable environment such as on a table in the workplace or at home By setting different detection levels for the computer depending on whether it runs with the AC power desktop or with batteries handheld or mobile usage the detection level automatically switches according to the power connection mode 3D Viewer This feature displays a 3D object on the screen which moves in according to tilting or vibration
206. y indicator shows the condition of the battery s charge green indicates the battery is fully charged orange indicates the battery is charging and flashing orange indicates a low battery condition Please refer to Chapter 5 Power and Power Up Modes for more information on this feature The Hard Disk Drive Optical Disc Drive eSATA indicator blinks green whenever the computer is accessing the built in hard disk drive optical disc drive or eSATA device The Memory media slot indicator blinks green when the computer is accessing the memory media slot This slot lets you insert an SD SDHC SDXC memory card minisD microSD Card Memory Stick PRO Duo PRO Duo Micro xD Picture Card and MultiMediaCard Refer to the Optional devices section in Chapter 3 Operating Basics for more information The Wireless communication indicator glows orange when the Wireless functions are turned on Some models are equipped with Wireless functions This indicator always show off with no effect Microphone A built in microphone allows you to import and record sounds for your application please refer to the Sound System section in Chapter 3 Operating Basics for more information Stereo speakers The speakers emit sound generated by your software as well as audio alarms such as low battery condition generated by the system Left side The following figure shows the computer s left side Figure 2 2 The
207. you cannot copy or playback protected material on another computer or other device and you may not reproduce any copyrighted material except for your personal enjoyment Below is a simple explanation for distinguishing SD memory cards from SDHC memory cards and SDXC memory cards E SD SDHC and SDXC memory cards appear the same externally However the logo on memory cards is different so pay careful attention to the logo when purchasing The SD memory card logo is sw The SDHC memory card logo is 2 E The SDXC memory card logo is sel E The maximum capacity of SD memory cards is 2GB The maximum capacity of SDHC memory cards is 32GB The maximum capacity of SDXC memory cards is 64GB Card Type Capacities SD 8MB 16MB 32MB 64MB 128MB 256MB 512MB 1GB 2GB SDHC 4GB 8GB 16GB 32GB SDXC 64GB Memory media format New media cards are formatted according to specific standards If you wish to reformat a media card be sure to do so with a device that uses media cards Formatting a memory media card Memory media cards are sold already formatted in conformity to specific standards If you reformat a memory card be sure to reformat it with a device such as digital camera or digital audio player that uses the memory cards not with the format command provided within Windows 3 36 7 Should you need to format all areas of the memory card including the J protected area you will need to obtain an appropriate application
208. ystal display LED light emitting diode MB megabyte MMC multi media card OCR optical character recognition reader PC personal computer PCI peripheral component interconnect RAM random access memory RGB red green and blue ROM read only memory RTC real time clock S P DIF Sony Philips Digital Interface Format SD Secure Digital SDHC Secure Digital High Capacity SDXC Secure Digital Extended Capacity SDRAM synchronous dynamic random access memory SLI Scalable Link Interface SSD Solid state drive TFT thin film transistor USB Universal Serial Bus UXGA ultra extended graphics array VGA video graphics array WAN wide area network WSXGA wide super extended graphics array WSXGA wide super extended graphics array plus WUXGA Wide Ultra Extended Graphics Array WXGA wide extended graphics array WXGA wide extended graphics array plus XGA extended graphics array User s Manual Glossary 2

Satellite Pro S850 User`s Manual

Contents

Download Pdf Manuals

Related Search

Related Contents