User Manual
Contents
1. Connecting the COz assembly cont 4 Place a new CO Cartridge into the cartridge holder and screw it firmly to the regu lator adaptor you may hear a sound once the cartridge is pierced Once attached do not unscrew the cartridge until all the pressure has been released see Removal and Cleaning on page 10 5 At this point the system should be completely connected you should now slowly turn the regulator clockwise to pressurize the system The dial on the gauge will rise gradually stop when it reaches 0 5 bar 6 With the pressure correctly set you can now place the whole CO assembly on the assembly stand and put it in the dispenser with the gauge facing the clear window 7 Slide the COz compartment door into place and now you will be ready to enjoy your beer Operation Always use clean glasses rinsed with very cold water at the time of serving Impu rities prevent the foam from forming on the glass Hold the glass under the dispensing tap making sure that the nozzle is not in con tact with the glass Pull the dispensing tap handle towards you while holding the glass at an angle The quantity of foam depends on the glass angle Set the glass upright as the beer level goes up Push the tap handle forward when the foam reaches the glass brim This will stop the beer from flowing Setting the temperature Use the up and down arrow buttons to set the desired temperature Note The dispenser has2. DC Power Cord AC Power Cord What comes with your beer dispenser 1 CO Regulator Installation 1 Carefully remove the unit from its packaging and check to see that no parts are missing or damaged keeping small plastic parts away from children at all times Place the dispenser on a steady flat surface leaving at least 4 on either side for proper ventilation Place the drip tray in the notch provided on the front of the unit Screw the Tap Handle into the tap and tighten Plug the appliance into a 110V AC or 12V DC electrical outlet using the proper cord Note Unit is not intended for use with 50 Hz outlets European Standard Preparing the keg First you must determine which type of keg you are using There are two basic types Pressurized with CO built in and Standard Before installation make sure that the keg has rested long enough to avoid foam coming out through the ventilation opening also cold beer will produce less foam than warm beer so pre chilling the beer in refrigerator for 6 12 hours is advised Your beer dispenser can cool a 5 Litre keg from 77 F to 41 F in 9 hours Warning Never put a keg into the freezer The beer might be damaged and the keg might burst Pressurized Kegs rer 1 Open the door and locate the two tubes that come You will not need any of the parts that come with the keg Tap and nozzle Instead of those parts you will be
3. GROUNDING TYPE WALL RECEPTACLE DO NOT UNDER ANY CIRCUMSTANCES REMOVE THE POWER CORD GROUNDING PRONG A separate adequately fused and grounded circuit should be available for this appliance Do not remove any grounding wires from individual components while servicing unless the component is to be removed and replaced tis extremely important to replace all grounding wires when rea Gefeiert components are replaced GROUNDING PLUG A WARNING ELECTRIC SHOCK HAZARD Disconnect electric supply from appliance before servicing Replace ail panels before operating Failure to do so could result in death or electrical shock e DO NOT USE A GROUND FAULT INTERRUPTER GFI A DEDICATED 15 AMP CIRCUIT IS HIGHLY RECOMMENDED 3 D Read the following instructions prior to operating this appliance Do not use the appliance if the power supply cord is damaged Should this be the case it must be replaced by a qualified person so that any potential shock hazard is avoided Prior to any connection check that the indicated operating voltage corro sponds to the voltage at the outlet This appliance is not designed for children Never allow unattended chil dren to use this appliance Prior to any cleaning and in general when the appliance is not in use make sure that it is not plugged in Make sure that your beer dispenser is set on a flat surface protected from the sun and avoid any other heat source The
4. a range between 38 F and 54 F the third button allows you to turn on an off the display to conserve energy when it is not being used Removal and Cleaning When the keg is empty it is advisable to thoroughly clean the beer dispenser before loading another keg de Empty the remaining gas using the pressure release Attach both hoses to the standard keg adapter and insert Open the cartridge chamber and turn the valve on the regulator counterclockwise to shut it off if you are using a standard keg Place a container under the dispensing tap and drain by pulling the handle towards you until nothing more flows out Open the keg compartment door and disconnect the hose s from the keg adaptor The connectors are released by pushing in the white button while pulling on the connector not the hose tool as indicated in Figure 8 Figure 8 Remove the keg adapter by pushing in the catch standard keg or squeezing the release tabs pressurized keg and pulling up until the adapter has cleared the keg To clean the keg first fill the cleaning bottle halfway with lukewarm water and a small amount of detergent into the bottle Note if you are using a pressurized keg the pressurized keg adapter will have to be washed separately Open the regulator valve and run the cleaning solution through the system for 5 seconds then repeat steps 6 8 using only water with no detergent Replacing the c
5. with in 12 twelve months from date of sale Since the natural variation in texture density grain color tone and shade of wood is unavoidable Seller does not guarantee the texture color tone or shade of the wood nor does seller guarantee the colorfastness of wood or against peeling chipping cracking or scratching Note Unfinished wood is subject to warping all wood surfaces must be sealed before placing cellar into service Improper placement of the unit will void the warranty This lim ited warranty does not cover damage due to such things as accident misuse abuse mishan dling neglect acts of God fires earthquakes floods high winds government war riot or labor trouble strikes lockouts delay of carrier unauthorized repair or any other cause beyond the control of the Seller whether similar or dissimilar to the foregoing Seller is not responsible for any damages caused to Seller s property resulting from the good This limited warranty applies only inside the Continental US Alaska Puerto Rico and Hawaii are not warranted Purchaser understands and acknowledges that the goods sold here are wine cellars cigar humi dors and or other similar units which house wine or cigars Purchaser assumes all risk of using these units including risk of spoilage humidity variations temperature variations leaks fire water damage mold mildew dryness and similar and any other perils that might occur Seller is not responsible f
6. appliance should be operated at room temperature between 54 F and 80 F Do not attempt to move the appliance while it is full so as to protect it from falling over When unplugging the unit always pull the plug and never the cord Never lift the appliance by the power supply cord or the dispensing tap Keep the power supply cord away from heat sources not intended for use in the garage Do not try to repair adjust or replace this appliances components by yourself Should it not operate correctly contact your dealer s customer support This appliance is designed for household use only and not for profes sional use Do not use for purposes other than that which it was de signed for Do not immerse the appliance or its power supply cord in water or any other liquid Do not cover the appliance or place anything on it Do not insert any object into the ventilation spaces Only use the CO Cartridges provided for this appliance Cartridges contain pressurized CO2 Keep them away from heat in a dry and cool place Do not throw away empty CO Cartridges into a fire Prior to operating the beer dispenser clean it using the instructions in this manual oo N 9 7 Oo P N Beer Dispenser Tap Handle Drip Tray Pressurized Keg Adapter Standard Keg Adapter Keg Seals 2 peices Pressure Release Tool Cleaning Bottle Regulator Adaptor CO Cartridge 3 peices Cartridge Holder CO Assembly Stand
7. artridge Three 16 gram cartridges are provided for approximately three 5 Litre kegs When the cartridge is empty replace it as follows d 2 3 Shut the pressure gauge valve turn it counterclockwise Unscrew the cartridge holder and replace the cartridge with a new one Open the pressure gauge valve and set it to the required temperature 10 Vinotemp International Seller and the person or entity that acquires these goods from Seller Purchaser hereby fully agree to the following terms and conditions of the sale Shipping fees are the responsibility of the Purchaser whether freight prepaid or freight collect Seller assumes no responsibility for the goods sold to the Purchaser once the goods have left the Seller s prem ises including but not limited to late delivery by the moving carrier or for events caused by any difficulty carrier incurs in attempting to fit the goods into the Purchaser s place of business or resi dence due to the size of the goods or otherwise Purchaser assumes all responsibility for delivery payment of freight access measurement installation hook up wiring moving and storage of the goods The transportation of all goods is subject to the terms and conditions which the moving carrier imposes on Purchaser including but not limited to additional charges imposed per flight of stairs and or additional charges resulting from the Carriere inability to safely and or adequately use the building elev
8. ator to lift the goods to an upper floor Any claim for damages incurred during shipment by the carrier of the goods are insured and handled directly with the carrier Any dam ages due to manufacture defects will be handled directly with Vinotemp International subject to the limited warranty All sales are final and unless authorized in writing by the Seller Purchaser may not return the goods under any circumstance If Purchaser refuses to accept the goods under any circum stance the Purchaser is liable for the return and cost of freight both ways and if Seller does take back the goods there will be a restocking charge that is 35 of the purchase price of the goods Custom Cabinet and Racking are non returnable Purchaser must notify Seller of non conform ing goods within four days of delivery after which time all goods are deemed accepted If an order has been placed and production has started cancellation of your order will be a 15 charge If Purchaser tenders payment with a check that has insufficient funds NSF or stops payment on a check or credit card for any reason Purchaser agrees to pay for all costs associated with the Seller s connection or litigation of such a claim including without limitation extra damages court costs and attorneys fees Finance charges begin the date of invoice Collection fees plus NSF fee of 50 will be added to your invoice which you agree to promptly pay Title to the goods does not pass until pa
9. eg NO INTERNATIONAL LOS ANGELES CALIFORNIA SUSA Thermoelectric Beer Dispenser VT BD User Manual Table of Contents 3 Important safety information 4 Instructions prior to operation 5 What comes in the box parts list 6 Installation instuctions pressurized keg 7 Installation instructions standard keg 8 Connecting the CO assembly 9 Operation Setting the Temperature 10 Removal and Cleanng 11 12 Terms and Conditions Warranty Replacement Cartridges This appliance is delivered to you with three 16 gram CO2 Car tridges which will enable you to use approximately 3 of the 5 Liter size beer kegs To order new cartridges which can be mailed directly to your home please call 800 777 8466 WARNING CO Cartridges contain compressed gas Do not puncture squeeze or modify the cartridge in any way Keep away from sources of heat and children Failure to use this product as it was originally intended could result in bodily injury and or death Important Safety Information AA WARNING To avoid the risk of electrical shock property damage personal injury or death The power cord must be plugged into a 3 prong grounding type wall receptacle grounded in accordance with the National Electrical Code ANSI NFPA 70 latest edition and local codes and ordinances it is the personal responsibility of the consumer to have a proper 3 prong wall receptacle installed by a qualified electrician
10. or incidental or consequential damages and there no warranties ex pressed or implied which extend beyond the Limited Warranty described above The implied warranties of merchantability and of fitness for a particular purpose are hereby expressly dis claimed Some states do not allow the exclusion of incidental or consequential damages or a waiver of the implied warranties of fitness and or merchantability so the above limitations may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state In the event of any dispute between Seller and Purchaser arising out of or relating to these terms and conditions or to the goods sold generally Purchaser must first file a written claim with Seller within ten days of the occurrence giving rise to the claim and wait an additional thirty days for a re sponse before initiating any legal action The sale and all terms are subject to California law Any legal proceeding arising out of or relating to these terms and conditions or to the goods sold gen erally shall be brought solely and exclusively in the County of Los Angeles In no event may Pur chaser initiate any legal proceeding more than six months after the occurrence of the event giving rise to the dispute The above terms and conditions are the only ones governing this transaction and Seller makes no oral representations of any kind These Terms and Conditions can only be modified in
11. using the Pressurized Keg Adapter as shown in figure 1 Figure 1 from the front of the dispenser For pressurized kegs you will only need the tube that connects directly to the tap It has the male connector the female connector has a white button on it Connects to Tap Figure 2 6 Pressurized Kegs cont 3 Press the Tap Hose connector into the pressur ized keg adaptor until it locks Pull lightly on connector to ensure that you have a tight fit Figure 3 4 You can now place the keg inside the dispenser Turn the keg so that the tube is not folded and proper flow is not obstructed as is shown in Figure 4 the other hose will hang freely on the side Figure 4 You are now ready to enjoy your beer for proper pouring instructions read the section called Operation on page 9 Standard Kegs 1 For all non pressurized kegs you will first want to follow the instructions that came with the keg for releasing excess gas Then you will want to determine which type of plug your keg has the types are listed below Note Combined Plugs and Vent Plugs Look identical from the top Rubber Plug Combined or Vent Plug 2 a Rubber Plug You will simply push the plug into the keg until it falls in you can use the tube end of the Standard Keg Adapter to push it through b Combined or Vent plug You will want to remo
12. ve the entire plug and replace it with one of the keg seals included with your dispenser Depending on which type of plug you have you may need to use pliers to remove it you will want to take caution not to bend the metal around the plug as this could cause an air leak It is common for part or all of the plug to fall into the keg during this step this is normal and it will not affect the flavor of your beer 7 Standard Kegs cont 3 Connecting the CO assembly 1 Locate the the two tubes comming from the front of Place the keg into the dispenser taking care not to Connect the regulator adapter to the bottom of the Open the compartment on the side of the dispenser Insert the standard keg adapter into the keg and lock it in place as shown in figure 5 and 6 Figure 5 1 the unit Connect both of them to their corrosponding g adapter they will only go in one way Push them in j until they click to ensure a proper seal fold the tubing or restrict proper flow of the beer You j are now ready to connect the CO assembly Locate the CO regulator and turn the valve counterclockwise until it stops to ensure tht the valve is shut ee regulator as shown in figure 7 Figure 7 to reveal the gas cartridge chamber and locate the unconnected tube coming from the beer keg Push this tube into the open hole on the regulator to dis connect push in the ring on the end while pulling the tube
13. writing signed by both Purchaser and Seller 04 07 Vinotemp International 17621 S Susana Rd Rancho Dominguez Ca 90221 www vinotemp com teste LISTED 12
14. yment is received in full by Seller and Seller retains a security interest in the goods until they are paid for in full LIMITED WARRANTY Seller warrants that the goods will be free of defects in materials and workmanship as follows Furniture style wood wine units all cooling unit parts for a period of 5 five years cabinetry and labor uninstalled for a period of 12 twelve months from date of sale removal and re installation of unit is not included in warranted labor For the metal cabinet wine units parts and labor for cooling system and cabinetry for a period of 12 twelve months from date of sale removal and re installation of unit is not included in warranted labor For a scratch and dent or refurbished unit warranty is 3 months from your dated invoice parts for function only not cosmetic Thermoelectric Units 90 ninety days from the date of sale This includes Wine Coolers Beer Dispensers and Refrigerators Cigar Humidors and Racking Systems are not war ranted Split Systems and installed products are parts only for 1 year no labor There is no war ranty on parts purchased separately Purchaser s exclusive remedy is limited at Seller s option to repair or replace defective part s with either new or factory reconditioned part s Purchaser is 11 responsible for shipping the unit pre paid to designated facility and Seller will pay return shipping charges in the continental United States for items repaired under warranty
Download Pdf Manuals
Related Search