Angle Grinder - Makita New Zealand
Contents
1. 2 Tua kite Angle Grinder 100 mm 9540 115mm 9541 125 mm 9542 DOUBLE INSULATION SPECIFICATIONS Model 9540 9541 9542 Depressed center wheel diameter s0s ssemmi 100 mm 115 mm 125 mm Spindle thread ou eee M10 M14 M14 No load speed min 10 000 10 000 10 000 Overall length 305 mm 305 mm 305 mm Net Weight warnen taa at antes 1 7 kg 1 7 kg 1 7 kg Due to our continuing program of research and development the specifications herein are subject to change without notice Note Specifications may differ from country to country Power supply The tool should be connected only to a power supply of the same voltage as indicated on the nameplate and can only be operated on single phase AC supply They are double insulated in accordance with European Standard and can therefore also be used from sockets without earth wire Safety hints For your own safety please refer to the enclosed safety instructions For European countries only Noise and Vibration of Model 9541 The typical A weighted noise levels are sound pressure level 88 dB A sound power level 101 dB A Wear ear protection The typical weighted root mean square acceleration value is not more than 2 5 m s Noise and Vibration of Model 9542 The typical A weighted noise levels are sound pressure level 88 dB A sound power level 101 dB A Wear ear protection The typical weighted root m2. that the wheel continues to rotate after the tool is switched off Do not touch the workpiece immediately after Operation it may be extremely hot and could burn your skin Position the tool so that the power cord always stays behind the tool during operation If working place is extremely hot and humid or badly polluted by conductive dust use a short circuit breaker 30 mA to assure opera tor safety Do not use the tool on any materials contain ing asbestos 24 Do not use water or grinding lubricant SAVE THESE INSTRUCTIONS OPERATING INSTRUCTIONS Installing the wheel guard Fig 1 amp 2 Mount the wheel guard with the tab on the wheel guard band aligned with the notch on the bearing box Then rotate the wheel guard 180 clockwise for 9526NB or counterclockwise for 9527NB and 9528NB Be sure to tighten the screws securely Installing side grip auxiliary handle Fig 3 For 9527NB and 9528NB only Screw the side grip on the tool securely The side grip can be installed on either side of the tool whichever is convenient Installing or removing depressed center wheel CAUTION Always be sure that the tool is switched off and unplugged before installing or removing the wheel Mount the inner flange onto the spindle Fit the wheel on over the inner flange and screw the lock nut onto the spindle Fig 4 To tighten the lock nut press the shaft lock firmly so that the spindle cannot revolve then use the loc
3. 1 2 10 11 12 Keep work area clean Cluttered areas and benches invite injuries Consider work area environment Don t expose power tools to rain Don t use power tools in damp or wet locations Keep work area well lit Don t use power tools in presence of flammable liquids or gases Guard against electric shock Prevent body contact with grounded surfaces e g pipes radiators ranges refrigerators Keep children away Do not let visitors contact tool or extension cord All visitors should be kept away from work area Store idle tools When not in use tools should be stored in dry high or locked up place out of the reach of children Don t force tool It will do the job better and safer at the rate for which it was intended Use right tool Don t force small tools or attachments to do the job of a heavy duty tool Don t use tools for purposes not intended for example don t use circular saw for cutting tree limbs or logs Dress properly Do not wear loose clothing or jewelry They can be caught in moving parts Rubber gloves and non skid footwear are recommended when working outdoors Wear protective hair covering to contain long hair Use safety glasses and hearing protection Also use face or dust mask if cutting operation is dusty Connect dust extraction equipment If devices are provided for the connection of dust extraction and collection facilities ensure these are connected and prope
4. ean square acceleration value is not more than 2 5 m s EC DECLARATION OF CONFORMITY The undersigned Yasuhiko Kanzaki authorized by Makita Corporation 3 11 8 Sumiyoshi Cho Anjo Aichi 446 8502 Japan declares that this product Serial No series production manufactured by Makita Corporation in Japan is in compliance with the following standards or standard ized documents HD400 EN50144 EN55014 EN61000 in accordance with Council Directives 73 23 EEC 89 336 EEC and 98 37 EC Yasuhiko Kanzaki CE 94 Director MAKITA INTERNATIONAL EUROPE LTD Michigan Drive Tongwell Milton Keynes Bucks MK15 8JD ENGLAND gt N ASF 4 Nu Symbols The following show the symbols used for the tool Be sure that you understand their meaning before use BA Read instruction manual a DOUBLE INSULATION Wear safety glasses RON Explanation of general view Wheel guard 5 Depressed center wheel Bearing box 6 Inner flange Screw 7 Spindle Lock nut 8 Lock nut wrench 9 Shaft lock 10 Switch lever 11 Brush holder cap 12 Screwdriver SAFETY INSTRUCTIONS Warning When using electric tools basic safety precautions should always be followed to reduce the risk of fire electric shock and personal injury including the following Read all these instructions before attempting to operate this product and save these instructions For safe operation
5. er wheels be sure to use oniv fiberglass reinforced wheels Check the wheel carefuliv for cracks or dam age before operation Replace cracked or damaged wheel immediatelv Observe the instructions of the manufacturer for correct mounting and use of wheels Handle and store wheels with care Do not use separate reducing bushings or adaptors to adapt large hole abrasive wheels Use only flanges specified for this tool Do not damage the spindle the flange espe cially the installing surface or the lock nut Damage to these parts could result in wheel breakage For tools intended to be fitted with threaded hole wheel ensure that the thread in the wheel is long enough to accept the spindle length Before using the tool on an actual workpiece test run the tool at the highest no load speed for at least 30 seconds in a safe position Stop immediately if there is any vibration or wob bling that could indicate poor installation or a poorly balanced wheel Check the tool to determine the cause Check that the workpiece is properly sup ported Hold the tool firmly Keep hands away from rotating parts Make sure the wheel is not contacting the workpiece before the switch is turned on Use the specified surface of the wheel to perform the grinding Do not use cutting off wheel for side grinding Watch out for flying sparks Hold the tool so that sparks fly away from you and other per sons or flammable materials Pay attention
6. h connection is required CAUTION The tool must be connected to a plug having a rated current greater than that of tool The rated voltage and current appear on the name plate IMPORTANT The wires in the mains lead are coloured in accordance with the following code NOTE CAUTION BLUE NEUTRAL BROWN LIVE As the colours of the mains lead of the tool may not correspond with the coloured markings identifying the terminals in your plug proceed as follows THE WIRE WHICH IS COLOURED BLUE MUST BE CONNECTED TO THE TERMINAL WHICH IS MARKED WITH THE LETTER N OR COLOURED BLACK THE WIRE WHICH IS COLOURED BROWN MUST BE CONNECTED TO THE TERMINAL WHICH IS MARKED WITH THE LETTER L OR COLOURED RED Neither wire is to be connected to earth terminal which is marked with the letter E or symbol on FOR 110 VOLT TOOL USE PLUGS TO BS4343 Makita Corporation Anjo Aichi Japan Made in Japan 883877A6
7. k nut wrench and securely tighten clockwise Fig 5 WARNING Only actuate the shaft lock when the spindle is not moving Switch action Fig 6 CAUTION Before plugging in the tool always check to see that the switch actuates properly and returns to the OFF position when the rear of the switch lever is depressed To switch on depress the rear of the switch lever and push it forward Then depress the front of the switch lever to lock it To switch off depress the rear of the switch lever Operation Fig 7 Hold the tool firmly with both hands Turn the tool on and then apply the wheel or disc to the workpiece In general keep the edge of the wheel or disc at an angle of about 15 30 to the workpiece surface During the break in period with a new wheel do not work the griader in the B direction or it will cut into the workpiece Once the edge of the wheel has been rounded off by use the wheel may be worked in both A and B directions WARNING lt should never be necessary to force the tool The weight of the tool applies adequate pressure Forc ing and excessive pressure could cause dangerous wheel breakage Continued use of a worn out wheel may result in wheel explosion and serious personal injury Depressed center wheel should not be used after it has been worn down to 75 mm 3 in diameter for Model 9526NB or 90mm 3 1 2 for Models 9527NB and 9528NB in diameter Use of the wheel after this poi
8. nt is unsafe and it should be removed from service and rendered unusable by intentional destruction ACCESSORIES CAUTION MAINTENANCE CAUTION Always be sure that the tool is switched off and unplugged before carrying out any work on the tool Replacing carbon brushes Fig 8 Remove and check the carbon brushes regularly Replace when they wear down to the limit mark Keep the carbon brushes clean and free to slip in the holders Both carbon brushes should be replaced at the same time Use only identical carbon brushes Use a screwdriver to remove the brush holder caps Take out the worn carbon brushes insert the new ones and secure the brush holder caps To maintain product safety and reliability repairs maintenance or adjustment should be carried out by a Makita Authorized Service Center These accessories or attachments are recommended for use with your Makita tool specified in this manual The use of any other accessories or attachments might present a risk of injury to persons The accessories or attachments should be used only in the proper and intended manner Wheel cover Inner flange Depressed center wheels Lock nut Rubber pad Abrasive discs O Lock nut 10 30 For abrasive disc Wire cup brush 75 br Wire bevel brush 85 UK only a DOUBLE INSULATION THE ADDITIONAL COMMENT OF ELECTRICAL CONNECTION The tool is double insulated for safety no eart
9. rly used Don t abuse cord Never carry tool by cord or yank it to disconnect it from receptacle Keep cord from heat oil and sharp edges Secure work Use clamps or a vise to hold work It s safer than using your hand and it frees both hands to operate tool 13 14 15 16 17 18 19 20 21 22 Don t overreach Keep proper footing and balance at all times Maintain tools with care Keep tools sharp and clean for better and safer performance Follow instructions for lubricating and changing accessories Inspect tool cords periodically and if damaged have repaired by authorized service facility Inspect extension cords periodically and replace if damaged Keep handles dry clean and free from oil and grease Disconnect tools When not in use before servicing and when changing accessories such as blades bits and cutters Remove adjusting keys and wrenches Form the habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on Avoid unintentional starting Don t carry plugged in tool with finger on switch Be sure switch is off when plugging in Outdoor use extension cords When tool is used outdoors use only extension cords intended for use outdoors and so marked Stay alert Watch what you are doing Use common sense Do not operate tool when you are tired Check damaged parts Before further use of the tool a guard or other part that is damaged
10. should be carefully checked to determine that it will operate properly and perform its intended function Check for alignment of mov ing parts binding of moving parts breakage of parts mounting and any other conditions that may affect its operation A guard or other part that is damaged should be properly repaired or replaced by an authorized service center unless otherwise indicated elsewhere in this instruction manual Have defective switches replaced by and authorized service center Do not use tool if switch does not turn it on and off Warning The use of any other accessory or attachment other than recommended in this operating instruc tion or the catalog may present a risk of personal injury Have your tool repaired by an expert This electric appliance is in accordance with the relevant safety rules Repairing of electric appli ances may be carried out only by experts other wise it may cause considerable danger for the user ADDITIONAL SAFETY RULES 1 2 10 11 12 13 14 15 16 18 19 20 21 22 23 ENBO31 3 Alwavs wear safetv goggles and ear protec tors during operation Alwavs be sure that the tool is switched off and unplugged before carrving out anv work on the tool Keep guards in place Use only wheels with correct size and wheels having a maximum operating speed at least as high as the highest No Load Speed marked on the tool s nameplate When using depressed cent
Download Pdf Manuals
Related Search