s.p . pId tune Inp Al Out Conf CoMM accs Inp. Out l.i np AlM EHit inp
Contents
1. range 9999 Square root o OFF 1 ON Noo Linear input characterization LOC Stored Setpoint tracking NO Remote Setpoint Slope enable No Control type PID col ounput on 0Ps theatro f0 Split range split range only Setpoint type rE henson utp pe EL eansnisiniow ange fp FEA pavananision igh ange foo IL fin digital input function AL Aln alarm type A Cuan addressing oP Lc hjAln latching no fot ce JALn start up disabling ane no Disables ALn on sensor break Parameterisation Parameter Name Setpoint selection Ratio remote Setpoint Remote Setpoint Bias Code m rogram parameters consult the Installation and user manual for details pres o Integral time rm 5 Q a es lt Start Stop Adaptive tuning Input filter Input shift Sampling time Parameter Name o Yawe e Default Parameter Name utput Hysteresis ycle time Control ouput low limit Control output high limit Control output maximum speed SEOPGonsanoumutngnvane o C a e e a A a e a C a a Cool output maximum speed a poo m oo po poo Communication SLAVE address SLAVE Baud rate SLAVE Communication protocol Parity Enable MASTER MASTER Baud rate w MASTER Communication protocol JBUS2. Process controller with Modbus Master Slave 1 8 DIN 48 x 96 2 eee X5 line Quick Guide e ISTR FX5ENGO02 ASCON TECNOLOGIC viale Indipendenza 56 27029 Vigevano PV Tel 39 0381 698 71 Fax 39 0381 698 730 internet site www ascontecnologic com E mail Sales ascontecnologic com Model Code The product code indicates the specific hardware configuration of the instrument that can be modified by specialized engineers only Line Basic Accessories Model EGE ESET CEANN Power supply 100 240Vac 15 10 24Vac 25 12 or 24Vdc 15 25 i Not available with split range control mode Parameterisation menu SE a SSEL mr Al alarm selection threshold 15t stored 2nd 3rd and yth Setpoint alarm thresholds d d 2 and 3 Al hysteresis Stored Setpoint asymmetric upper Setpoint Al Le low limit a ric oe pon Ali delay high limit Slope up and 3rd and yth alarm hysreresis nd del Slope down ane Parameter list Declaration of Conformity and Manual retrieval X5 is panel mounting Class Il instrument It has been designed with compliance to the European Directives All information about the controller use can be found in the User Manual MIU_X5_EN pdf The Declaration of Conformity and the manual of the controller can be downloaded free of charge from the web site www ascontecnologic com Once connected to the web site search X5 then cl
3. ick on X5 from the result list In the lower part of the product page in any language is present the download area with links to the documents available for the controller in the available languages A Warning Whenever a failure or a malfunction of the device may cause dangerous situations for persons things or animals please remember that the plant must be equipped with additional devices which will guarantee safety We warrant that the products will be free from defects in material and workmanship for 18 months from the date of delivery Products and components that are subject to wear due to conditions of use service life and misuse are not covered by this warranty Configuration menu Configuration Operator mode P 275 0 Enter the configuration password Press GSMuntil A Setpoint Input type type inaari Stored Engineering Setpoint units Tracking If linear scales are Setpoint slope choosen set also the time units following parameters Remote Setpoint Number input of decimals Remote Slope Low range Setpoint enable High range Square root Linear inputs characterisation Manual Cool integral automatically stored in reset C time Phi Es and k d parameters Proportional Cool derivative Copy these PID values m time for back up channel Proportional Initial tune Filter time band constant Integral Continuous Measure time tune start bias o When Adaptive tune i
4. nsmitted output selection 2nd retransmission output Dead band Cool cycle time Control output ee rate limit enero Cool control Control Output output high soft start value limit PID only y Soft start Cool output A rate limit user enabled time ae Electrical connections Pin connector Fork shape AMP165004 5 5 mm 0 21in Stripped wire L5 5mm 0 21 in Z 1 4mm 0 055 in max 2 d retransmission low range 2nd retransmission high range Li digital input function Ali alarm type IL2 digital Ali output input function address IL3 digital input function ALT arcing Ali start up blocking Disables ALi on sensor break Output adressing Latching Blocking Disabling for Al2 AL3 and AL4 Consult the Installation and User manual for details Consult the Configuration menu previously described address comm s SLAVE baud rate SLAVE comm s protocol Parity MASTER enable MASTER baud rate MASTER comm s protocol The parameters pointed out with grey background are those necessary to configure the options and are NOT shown in the menus All the parameters are fully described and explained in the user manual of the controller Configuration Code we lo Default User Lim a Engineering units NONE Lo Number of decimals 0 3 o Parameter Name Low range High
5. s Sampling selected the instrument time displays Fib E 1 and tuck Error dead band PID values calculated for the process 2 Overshoot control 2 These values are not Description and dimensions Depth 10 mm 48 mm 3 Digital Inputs X5 PY control input op 1112 13 Lil ae LEDs yellow in eng units Control output VL J or program status SUAT Cr 9 Status LEDs at I SP operating Setpoint Eg green HLD 82 L D f Local Remote or Stored 4 Alarm status eee AV Control Output LEDS red CD LEDs red CaJOP1 4 ON COP2 y OFF Run Stop Timer ram Auto Man SA pIag Menu access Enter key for selection setting confirmation O Setpoint setting Panel cut out and mounting 456mm 14 7600 in Control type Main output Heat Secondary output Cool Cool output on OP5 Main output safety value Main output forcing value Split range Split Range Control action Operator mode Press until 1 08 1 J ob A KA When PID algorithm is selected set the following parameters Cycle time Control Output low limit Control Output high limit 1t retransmitted output selection 1 retransmission output 15t retransmission low range 15t retransmission high range 2d retra
Download Pdf Manuals
Related Search