FOUR-PORT ADSL ROUTER
Contents
1. access the Internet First check whether PC can ping the interface Ethernet IP address of this product successfully default value is 192 168 1 1 by using ping application If ping application fails please check the connection of Ethernet cable and check whether the states of LEDs are in gear If the PC uses private IP address that is set manually non registered legal IP address please check 1 Whether IP address of the PC gateway is legal IP address Otherwise please use the right gateway or set the PC to Obtain an IP address automatically 2 Please confirm the validity of DNS server appointed to the PC with ADSL operator Otherwise please use the right DNS or set the PC to Obtain an IP address automatically 3 Please make sure you have set the NAT rules and convert private IP address to legal IP address IP address range of the PC that you specify should meet the setting range in NAT rules Central Office equipment may have problem PC cannot browse Internet web page Please make sure DNS server appointed to the PC is correct You can use ping application program to test whether the PC can connect to the DNS server of the ADSL operator Initialization of the PVC connection failed Be sure that cable is connected properly from the DSL port to the wall jack The DSL LED on the front panel of the ADSL router should be on Check that your VPI VCI type of 14 ADSL ROUTER USER MANUAL encapsulation and type of multiplexing setti2. KD318RI ADSL Router ADSL ROUTER USER MANUAL NOTICE This document contains proprietary information protected by copyright and this Manual and all the accompanying hardware software and documentation are copyrighted All rights are reserved No part of this document may be photocopied or reproduced by mechanical electronic or other means in any form The manufacturer does not warrant that the hardware will work properly in all environments and applications and makes no warranty or representation either expressed or implied with respect to the quality performance merchantability or fitness for a particular purpose of the software or documentation The manufacturer reserves the right to make changes to the hardware software and documentation without obligation to notify any person or organization of the revision or change All brand and product names are the trademarks of their respective owners Copyright 2004 All rights reserved Content Di COW ON VIC W A TAN 1 1 Ie tic NN 2 1 2 Packet Contents nece ert ces ere er rere ere a Ferrer eer dsp Ses rere A Pa deb degrees dnd 3 1 3 System Requirements ua ia ee e se e rr e RD eios 4 1 4 Factory Defaults 32 tete Ctt rt tee tree edet tert 4 1 5 Warnings and Cautions uie eee ep re Ronde ter m RI ar eR Tees 4 Hardware D scriptl n iiic ia Hardware Installation nA Software Installation Ed PC Configuration Guide eire s oris ern Paten ae deos epe eed Serre eH ade
3. and check whether there is VPI VCI value provided by operator If not please operate according to steps 5 3 Editing PVC till the instructions shown in the figure display Connection Type Select the type of network protocol and encapsulation mode over the ATM PVC that your ISP has instructed you to use C PPP over ATM PPPOA PP over Ethernet PPPoE MAC Encapsulation Routing MER IP over ATM IPoA Bridging Encapsulation Mode LLC SNAP BRIDG ING y Select PPP over Ethernet PPPoE in Connection Type and LLC SNAP BRIDGING 11 ADSL ROUTER USER MANUAL in Encapsulation Mode and then click Next Enter user name and password provided by operator then click Next PPP Username and Password PPP usually requires that you have a user name and password to establish your connection In the boxes below enter the user name and password that your ISP has provided to you PPP Username PPP Pa rd PPPoE ce Name Authentication Method AUTO X Click Next in the following page Enable IGMP Multicast and WAN Service Enable WAN Service M Q D a D a m Click the Save button in the summarize page to save the settings Select from Management Save Reboot and then click the Reboot button to restart the ROUTER If factory default settings of ROUTER includes VPI VCI provided by operator please select from Advanced Setup gt WAN and fi
4. are driving program Choose the soft driver in the assigned position and press next the system will automatically install the driving program recorded on the soft disk into the system ADSL ROUTER USER MANUAL 5 PC Configuration Guide 5 1 5 1 1 1 Local PC Configuration Windows 95 98 ME XP In the Windows task bar click the Start button point to Settings and then click Control Panel Double click the Network icon On the Configuration tab select the TCP IP network associated with your network card and then click Properties In the TCP IP Properties dialog box click the IP Address tab Set the IP address as 192 168 1 x x can be a decimal number from 2 to 254 like 192 168 1 2 and the subnet mask as 255 255 255 0 On the Gateway tab set a new gateway as 192 168 1 1 and then click Add Configure the DNS tab if necessary For information on the IP address of the DNS server please consult with your ISP Click OK twice to confirm and save your changes You will be prompted to restart Windows Click Yes 5 1 2 Windows 2000 1 In the Windows task bar click the Start button point to Settings and then click Control Panel Double click the Network and Dial up Connections icon In the Network and Dial up Connections window right click the Local Area Connection icon and then select Prop
5. condary DNS Server 192 168 1 1 5 3 Edit PVC l Click Device info WAN to check whether the pre defined PVC values contain the value you need WAN Info VPI VCI Con ID Category Service Interface Protocol Igmp QoS State Status IP Address 0 35 1 UBR br 0 35 nas 0 35 Bridge N A Disabled Enabled ADSL Link Down 2 If not please select from Advanced Setup gt WAN and click Edit button 10 ADSL ROUTER USER MANUAL 5 4 Wide Area Network WAN Setup Choose Add Edit or Remove to configure WAN interfaces Choose Save Reboot to apply the changes and reboot the system VPI VCI Con ID Category Service Interface Protocol Igmp QoS State Remove Edit r Edit nas D 35 Bridge N Disabled Enabled Add Remove Save Reboot 0 35 1 UBR or n 35 Please enter the VPI VCI value you want and continue clicking the Next button till the confirmation page displays ATM PVC Configuration This screen allows you to configure an ATM PVC identifier VPI and VCT and select a service category ver 0 255 p ver a2 65535 BS Service Category UBR Without PCR y Click the Save button in the summarize page to save the settings Select from Management gt Save Reboot and then click the Reboot button to restart the ROUTER Routing mode setting Click Device Info gt WAN
6. d of telephone otherwise ADSL router may occur frequently off line ADSL ROUTER USER MANUAL 2 Hardware Description Front Panel Function On Power Off No power or system boot failed Strady ADSL link established and active Blinking ADSL is trying to establish a connect Blinking ADSL data activity occurs Off No ADSL data is being sent or received On LAN link established and active Blinking ADSL data activity occurs Off No LAN link Rear Panel Function Connects the device to an ADSL telephone jack or splitter using a RJ 11 telephone cable Connects the device to your PC s Ethernet port or to the uplink port on your hub switch using a RJ 45 cable System reset or reset to factory defaults Connects to the supplied power adapter Switches the unit on and off ADSL ROUTER USER MANUAL Hardware Installation This Hardware Installation describes how to connect ADSL router to your computer LAN and the Internet This Installation assumes you have subscribed to an ISP for ADSL service and only covers the basic configurations to be applied to residential or corporate networks Hardware Connection 1 Wall outlet with Splitter Es aq ASDL service Line Modemi aper Phone y Power Outlet Using a telephone line to connect the DSL port of ADSL router to the MODEM port of the splitter and using a other telephone line connect your telepho
7. eacaededeseciee D 5 1 I ocal PE Configuration tre p a aote e e dor eere eter 9 5 2 Access the program aa aeta eta RR HR tb ete n Hp man edes 10 5 3 EUA GE 10 5 4 Routing mode Setting tene e eL ede De P OH Cem ce e n ed n en 11 5 5 Reset RO ter citrato 12 Appendix Frequent Asked Questions eee eese e eene eee eee eee ense esee sees sssees sees LA n bk UT ADSL ROUTER 1 Overview USER MANUAL Thank you for using this Asymmetric Digital Subscriber Line ADSL router With the asymmetric technology this device runs over standard copper phone lines In addition ADSL allows you to have both voice and data services in use simultaneously all over one phone line It is an ideal solution for the small and medium size business environment This ADSL router provides a 10 100BaseT interface for Ethernet connection and an USB interface for USB connection at the user end Computers can simultaneously connect to the route either via its USB Switch or both ports to share its high speed Internet access You can connect to its Switch port regardless of the operating system you are using or connect to its USB port to allow easy installation to a USB equipped computer It receives adaptive rates up to 24Mbps and transmits 1Mbps upstream 1 1 Features 1 1 1 ADSL Compliance ANSITI 413 issue 2 Dying Gasp VLAN tagging Downstream Up to 24Mbps Max upstream speed 1Mbps Rate Adaptive a
8. erties Highlight Internet Protocol TCP IP and then click Properties In the Internet Protocol TCP IP Properties dialog box set the IP address as 192 168 1 x x can be a decimal number from 2 to 254 and the subnet mask as 255 255 255 0 and the default gateway as 192 168 1 1 Then click OK Configure the DNS tab if necessary For information on the IP address of the DNS server please consult with your ISP Click OK twice to confirm and save your changes ADSL ROUTER USER MANUAL 5 2 Access the program After configuring the IP Address of you computer powering on the ADSL Router and launching a web browser such as Internet Explorer use http 192 168 1 1 to log on to setting page Enter Network Password 21 xi Please type your user name and password and password adslroot Site 132 168 1 1 Realm ADSL Modem Enter username admin Save this password in your password list Attention the username and password are both lowercase All the parameters shown in this page are the factory default settings Device Info Board ID Software Version 3 00L 01 B2pBO17k di5h Bootloader CFE Version 1 0 37 0 6 This information reflects the current status of your DSL connection Line Rate Upstream Kbps Line Rate Downstream Kbps LAN IP Address 192 168 1 1 Default Gateway Primary DNS Server 192 168 1 1 Se
9. nd corresponding VPI VCI value in the page and click the Edit button Then follow the steps as specified above After routing settings are finished if you want to enable DHCP service then please set IP address of PC network card to obtain an IP address automatically If you don t want to enable DHCP service then you need to assign an IP address for your PC network card and set DNS address to the address provided by operator If operator doesn t provide the DNS address then the address is set to 192 168 1 1 that is the address of ROUTER Note If you want to cancel all modification that you do on the router please select from 5 5 Management gt Setting gt Restore Default Settings to restore factory default settings Reset Router For convenience shutdown your computer first 1 Switch the ADSL router OFF 12 ADSL ROUTER USER MANUAL 2 On the Rear Panel of the ADSL router you will find a small hole with the word reset written below it It s just big enough for a ball point tip Insert a ball point tip into this little hole actually it s a reset switch and keep the ball point tip in there 3 Switch the router ON and hold the ball point tip in the little hole You can release the ball point after about 10 seconds You have then completed the full reset Your ADSL router will now have its factory default settings IP address will be 192 168 1 1 and the subnet mask will be 255 255 255 0 Now you can reboot y
10. ne to the PHONE port of the splitter then connect the wall phone jack to the LINE port of the splitter The splitter comes with three connectors as below LINE Connects to a wall phone jack RJ 11 jack MODEM Connects to the DSL jack of ADSL router PHONE Connects to a telephone set Using an Ethernet Cable to connect the LAN port of the ADSL router to your LAN or a PC with network card installed Connect the power cable to the PWR connector on ADSL router then plug in the AC power adapter to the AC power outlet and then press the on off button POWER RESET ON e a 4 OFF A Notes Without the splitter and certain situation transient noise from telephone can interfere with the operation of the ADSL router and the ADSL router may introduce noise to the telephone line To prevent this from happening a small external splitter must be connected to each telephone ADSL ROUTER USER MANUAL 4 Software Installation This chapter shows you how to install the router s USB drivers when PC connects to the router via its USB port 1 Insert the rectangular end of a USB cable into the USB port of your PC 2 Insert the square end of the USB cable into the USB port of the Router 3 Power on the router and then a dialog box of A new hardware is found is displayed on the screen 4 Press Next button the system then search for hardw
11. ng are the same as what you collected from your service provider Re configure ADSL router and reboot it If you still can not work it out you may need to verify these variables with the service provider If the cause is not above given please contact your local service provider 15
12. our PC again 13 ADSL ROUTER USER MANUAL Appendix Frequent Asked Questions Q A gt gt Q PO Q gt Q None of the LEDs are on when you power on the ADSL router Please make sure what you use is the power adaptor attached with the ADSL router package and check the connection between the AC power and ADSL router DSL LED does not turn on after connect telephone line Please make sure what you use is the standard telephone line as attached with the package make sure the line is connected correctly and check whether there is poor contact at each interface Wait for 30 seconds to allow the ADSL router establishes connection with you ADSL operator DSL LED is in the circulation of slow flashing and fast flashing after connect telephone line This situation means the ADSL router is in the status of failing to establish connection with Central Office Please check carefully and confirm whether the ADSL router has been installed correctly LAN LED does not turn on after connect Ethernet cable Please make sure Ethernet cable is connected hub PC and ADSL router correctly Then please make sure the PC hub have been power on Please make sure that you use parallel network cable to connect UpLink port of hub or use parallel network cable to connect PC If connect normal port of hub not UpLink port you must use cross cable Please make sure that your network cables meet the networking requirements above PC cannot
13. t 32 Kbps steps Interoperable with all major DSLAM equipment TR 068 TR 069 1 1 2 Standards amp Protocols Conformance ITU G994 G 992 1 G DMT G 992 2 G LITE G 992 3 ITU G992 3 GDMT BIS ITU G 992 5 T1413 PPPoE PPPoA IPoA 1 1 3 Operating System Support WINDOWS 98 WINDOWS 98 SE ADSL ROUTER USER MANUAL 1 2 WINDOWS ME WINDOWS 2000 WINDOWS XP Macintosh LINUX ATM Capabilities ATM Connection VPI Range 0 255 VCI Range 32 65535 Auto search PVC AESA E 164 DCC ICD SVC amp PVC Support UNI 3 0 amp 3 1 Signaling Support AAL 5 Management Support Web Based GUI Upgrade or update via FTP HTTP Command Line Interface via Telnet Diagnostic Test Firmware upgrade able for future feature enhancement Environmental Operating humidity 1096 9096 non condensing Non operating storage humidity 596 9596 non condensing Packet Contents The packet contents are as the following ADSL Router x1 External Splitter x1 AC adapter x1 Telephone Line x2 Ethernet Cable x User Manual x1 USB Cable x1 CD x1 ADSL ROUTER 1 3 1 4 1 5 USER MANUAL System Requirements Before using this ADSL router verify that you meet the following requirements Subscription for ADSL service Your ADSL service provider should provide you with at least one valid IP address static assignment or dynamic assignment via dial up connection One or more computers each contains an E
14. thernet 10 100M Base T network interface card NIC A hub or switch if you are connecting the device to more than four computers For system configuration using the supplied web based program A web browser such as Internet Explorer v5 0 or later or Netscape v4 7 or later Factory Defaults The device is configured with the following factory defaults IP Address 192 168 1 1 Subnet Mask 255 255 255 0 Encapsulation RFC 2516 LLC VPI VCI According to local information Warnings and Cautions Never install telephone wiring during storm Avoid using a telephone during an electrical storm There might be a risk of electric shock from lightening Do not install telephone jacks in wet locations and never use the product near water To prevent dangerous overloading of the power circuit be careful about the designed maximum power load ratings Not to follow the rating guideline could result in a dangerous situation Please note that telephone line on ADSL router must adopt the primary line that directly outputs from junction box Do not connect ADSL router to extension phone In addition if your house developer divides a telephone line to multi sockets inside the wall of house please only use the telephone that has connected with the splitter of ADSL router when you access the Internet Under the above condition if you also install telephone with anti cheat dial device ADSL ROUTER USER MANUAL please pull out this kin
Download Pdf Manuals
Related Search