User Guide - Nightingale Care Beds Ltd
Contents
1. Total bed lockout feature Includes Trendelenburg Reverse Trendelenburg Chair Positioning CPR and Auto Contour functions Head section and bed frame angle monitor MOULDED QUAD RAILS Pass all new FDA guidelines for bedrail entrapment IEC 60601 2 52 Provide assistance freedom and protection for patients SAFETY FEATURES Ultra low height of 8 25 200mm prevents patient falls Passes all new 2006 FDA Bedrail Entrapment Guidelines Fasy access to Central Lock and Steer pedal at head end and foot end Patient control positioning One button chair positioning Secure caster locking system Detachable mattress deck facilitates infection control CENTRAL LOCK AND STEER SYSTEM Colour coded foot pedal has three functions complete caster lockout neutral total swivel and steer mode for single attendant bed transport BED EXIT ALARMS OPTIONAL Alarm sounds in patients room when patient gets out of bed PATIENT CONTROLS AND LOCK OUT Can add optional 6 function electric Hand Pendant Patient access can be locked out from each or alll patient controls Bed can be extended by 4 100mm Built in emergency battery back up systems Battery monitor Instant CPR release button Total bed lock out feature Bed Exit Alarm system optional Removable headboard and footboard Easy to read angle indicators for degree of Head amp Trendelenburg Ergonomically designed quad rails SPIRIT can be used with a wid2. LOCK position ACTIVATE CHAIR MODE Press and hold the CHAIR button on the staff control pad DIA 28 Release the button once the chair configuration is reached bed will stop automatically See DAI 29 The green Chair light will illuminate once the proper Reverse Trendelenburg angle has been achieved To deactivate the Chair Mode press and hold the CHAIR button until the bed is flat The bed will stop automatically CPR CARDIOPULMONARY RESUSCITATION MODE Improper use of CPR mode may cause patient injury A Once activated CPR function will lower head and knee sections to flat position automatically To interrupt CPR function touch any other button on the keypad Activation of the CPR control allows one touch flattening of all bed surfaces ACTIVATE CPR MODE Press the CPR button on the staff control pad one time The head section and knee section will lower to flat position See DIA 30 and 31 The CPR mode does not need deactivation Simply resume head and knee foot operation once the CPR action is complete To Interrupt the CPR mode touch any other function on the keypad SPIRIT USER MANUAL VERSION 01 2013 PAGE 7 20 MONTCALM International PATIENT LOCKOUTS ACTIVATE INDIVIDUAL FUNCTION LOCKOUTS m Patient Lock out restricts the patient from activating various bed features via the quad rail control pad The degree of restriction depends on the lock out option selected
3. See DIA 13 HEAD ELEVATION HEAD MOTOR FUNCTION To raise the head section of the bed press the HEAD UP arrow on the staff control pad See DIA 14 Release the button when the desired level is reached See DIA 15 To lower the head section of the bed press the HEAD DOWN arrow on the staff control pad See DIA 16 Release the button when the desired level is reached See DIA 17 KNEE ELEVATION FOOT MOTOR FUNCTION To raise the Knee section of the bed press the KNEE UP arrow on the staff control pad See DIA 18 Release the button when the desired level is reached See DIA 19 To lower the Knee section of the bed press the KNEE DOWN arrow on the staff control pad See DIA 20 Release the button when the desired level is reached See DIA 21 SPIRIT USER MANUAL VERSION 01 2013 SPIRIT the low bed DIA 15 DIA 17 DIA 19 DIA 21 PAGE 5 20 x MONTCALM International AUTO CONTOUR ACTIVATE AUTO CONTOUR In order to prevent patients from sliding towards the footboard as the head section is elevated it may be beneficial to use the auto contour function This function will automatically raise lower the knee section whenever the head section is raised or lowered DIA 22 To activate auto contour simply press the CONTOUR button at the bottom right corner of the staff control pad DIA 23 When the green light is illuminated the auto contour
4. See DIA 39 PAGE 14 20 SPIRIT USER MANUAL VERSION 01 2013 SPIRIT the low bed OPTIONAL EASY BED EXTENSION RETRACTION SYSTEM To accommodate the physical needs of taller patients while maintaining the easy of frequent bed movement about space Can ned a ee facilities Carroll Hospital Group offers an optional Easy Bed extension system that allows for easy and rapid extension retraction of the mattress deck by 4 inches 102 mm from 80 2032 mm to 84 2134 mm No tools are required to perform bed Easy Bed extension retraction operations If your Spirit bed has been equipped with the optional Easy Bed Extension system the bed will be outfitted with two clamping knobs and an extendable foot deck section of the mattress deck as shown below 2 Grasp footboard bracket by the corners as shownabove Gently and smoothly pull away from the headof the bed until the footboard bracket slidemechanism contacts its mechanical stops 1 Elevate bed to comfortable working height Unclamp the footboard bracket slide mechanism by turning both knobs counter clockwise until they come to stop on their retention brackets we PN p ji Knob clamped Knob unclamped and contacting retention bracket 3 Clamp the footboard bracket slide mechanism by turning both retention knobs clockwise until hand tight IMPORTANT Ensure that the clamping knob fastener extends through the retention hole located in t
5. USER MANUAL VERSION 01 2013 PAGE 13 20 MONTCALM International p T HE E g ww g EE b l A ht y A f b A IN JVC FA IX i PIN V YN SALOTE Is FA Y gir Y i d Pagi i amp Y aE ceu 4 The bed is mobile in either the NEUTRAL or STEER modes Use either of these modes depending on the situation when bed mobility is needed ACTIVATE STEER MODE 1 Fully depress the right side of the central lock amp Steer pedal at either end of the bed See DIA 36 2 Slide the bed sideways in a back and fourth motion at the foot end of the bed until the steering casters are engaged See DIA 37 NOTE When the NEUTRAL mode is activated properly the bed should move freely without any unusual noises If any clicking noises are present in the neutral mode stop and check that the pedal is level Adjust if necessary ACTIVATE NEUTRAL MODE l Press or lift the pedal with your foot until the pedal is level 32955 E i A TE a g m zy mm g 5 559 h A m mpm n b LN ZN J J TAN 3 FN um ZX KA n ZX Wu Y Ls P E J LAN a pi J fn J X JF NI d q Ea B Ram 8 AJ WE EB few Y The bed is stable in the LOCK mode Use this mode whenever the bed is left unattended or when the bed needs to remain stable DIA 39 ACTIVATE LOCK MODE 1 Fully depress the left side of the Central Lock amp Steer pedal at either end of the bed
6. damage CAUTION Information appearing under the CAUTION caption concerns the protection of personnel from potential hazards that can result in minor personal injury or equipment damage WARNING Information appearing under the WARNING caption concerns the protection of IMPORTANT ELECTRICAL SAFEGUARDS Plug the three prong electrical cord ONLY into a properly grounded 230 VAC 50 cycle outlet DO NOT use an extension cord DO NOT permit the cord wall outlet to become wet DO NOT operate the bed if the cord or outlet is damaged DO NOT operate the bed if any motor has malfunctioned or is damaged in any manner During routine bed cleaning always unplug the three prong plug from grounded outlet DO NOT roll the bed over the power cord DO NOT entangle the cord on other objects A pinched electric cord is dangerous and can become damaged Be aware of the power cord location especially when moving the bed AUXILIARY BATTERY NOTE The battery is continuously charged as long as the bed s power supply is plugged into a 230 VAC wall outlet gt PR gt PAGE 2 20 SPIRIT USER MANUAL VERSION 01 2013 SPIRIT the low bed IMPORTANT MECHANICAL SAFEGUARDS DO NOT stand on the bed or concentrate weight on a single fiberglass deck panel DO NOT use the bed without a mattress at least 4 100mm thick and of recommended dimensions MATTRESS SPECIFICATIONS A mattress is not included with this bed It is highly re
7. faulty connection or component CBO9 control box CB10 control box battery and or connection cable Confirm all connections and begin troubleshooting potentially faulty components OR The bed has been disconnected from an AC power outlet and the battery has been automatically disengaged from the Daey circuit because the voltage has dropped below 18VDC Reconnect bed to an AC power outlet and allow battery to charge for 24hr In house testing has demonstrated that a new back up battery when fully charged has sufficient power to deliver the equivalent of approximately 5 CPR cycles with a patient weight of 20 Stone 1 20kgs Battery power discharge rate depends upon factors such as patient weight age of battery ambient temperature and humidity and the number of charge discharge cycles the battery has been subjected to For example the heavier the patient the faster battery power will be exhausted during battery powered bed operation Conversely the lighter the patient battery power may offer a longer duration of battery powered bed operation PAGE 9 20 MONTCALM International PATIENT QUAD HEAD ELEVATION FUNCTION To raise the head section of the bed press the HEAD UP arrow release the button when the desired level is reached To lower the head section of the bed press the HEAD DOWN arrow release button when the desired level is reached KNEE ELEVATION FUNCTION To raise the knee section of
8. function is active STAFF AND EMERGENCY FUNCTIONS TRENDELENBURG AND REVERSE TRENDELENBURG OPERATION Patient discomfort may result from normal operation of the Trendelenburg or Reverse Trendelenburg function Trendelenburg and Reverse Trendelenburg modes should only be used on the advice of a medical practitioner The Spirit bed may shift during Trendelenburg or Reverse Trendelenburg activation Tredelenburg or Reverse Trendelenburg must be operated ONLY after the bed has been stabilized in the Central Lock amp Steer LOCK position ACTIVATE TRENDELENBURC MODE 1 Press and hold the TREND button on the staff control pad Release the button once the desired bed angle between O and 15 is reached See DIA 24 and 25 2 To return the bed to level press and hold the REV TREND button until the bed automatically stops ACTIVATE REVERSE TRENDELENBURG MODE 1 Press and hold the rev TREND button on the staff control pad Release the button once the desired bed angle between O and 13 is reached See DIA 26 and 27 2 To return the bed to level press and hold the TREND button until the bed automatically stops DIA 26 DIA 27 DIA 25 PAGE 6 20 SPIRIT USER MANUAL VERSION 01 2013 SPIRIT the low bed CHAIR MODE The Chair function allows patients to be placed in an upright postion fi Chair mode must be operated only after the Central Lock amp Steer pedal has been put in the
9. MONTCALM International the low bed specialist The SPIRIT Ultra Low Bed USER MANUAL It is the duty of all staff who handle the SPIRIT bed to read these GUIDANCE NOTES FOR SAFE USE CALL OUR HELP LINE ON 01865 409926 IF YOU NEED ADVICE OR FURTHER INSTRUCTION SPIRIT USER MANUAL VERSION 01 2013 PAGE 1 20 MONTCALM International INTENDED USE The Spirit Bed is intended for low to moderately acute patients in the medical and or surgical area of the hospital The Spirit Bed is also intended for use as a general purpose variable height hospital bed for general care post operative and general medicine wards STANDARD CONVENTIONS USED IN THIS MANUAL This manual includes information essential to the safety of the patient personnel and equipment during the normal operation of the Spirit Bed Before operating the Spirit Bed be sure you read and understood the contents of this manual It is important that you use this equipment in accordance with the procedures outlined in this manual As you read through this manual be alert to the three signal words DANGER Information appearing under the DANGER caption concerns the protection of personnel from the immediate and imminent hazards that if not avoided will result in immediate serious personal injury or loss of life in addition to equipment damage personnel from potential hazards that can result in personal injury or loss of life in addition to equipment
10. Staff may choose to lock patients access to one two or all three bed functions To restrict a function press the PATIENT LOCK button under that particular function see DIA 32 The lock icon will illuminate when the function is locked out for the patient To unlock press the same button again When the light is not illuminated the patient has access to that function NOTE When patient functions have been locked the staff footboard control pad remains active ACTIVATE TOTAL LOCK OUT To completely restrict access to all bed functions from all control points staff and patient controls use the total lock out function Press and hold all three lock out buttons at the same time DIA 33 All functions on the staff footboard control pad and all patient controls are unavailable Total lock out is active when all three lock out buttons flash sequentially To deactivate the total lock out feature repeat the process by pressing and holding all three lock out buttons at the same time fux When left unattended the bed should be lowered to its lowest position with the Bed Elevation function locked out in order to reduce the risk of patient injury PAGE 8 20 SPIRIT USER MANUAL VERSION 01 2013 SPIRIT POWER STATUS INDICATOR The enhanced footboard staff control on the Spirit Select is equipped with an integrated power status indicator This cluster of 3 discrete icons indicate the realtime status of power a
11. TOR LED IS SOLID RED Bed is disconnected from an AC power outlet and is operating on battery power The battery is connected to the CB10 control box and has not yet exhausted the available battery power Bed is OK to operate on battery power but it should be connected to an AC power outlet as soon as is possible to recharge the battery IMPORTANT Exercise caution when operating the bed on battery power Ensure that only vital and SPIRIT M USER MANUAL VERSION 01 2013 SPIRIT the low bed Uo Mn o AC DC ATTN are performed to exten battery ie as long 7 as possible and ensure emergency functions BATTERY remain available when needed INDICATOR LED IS FLASHING RED Bed is disconnected from an AC power outlet and has been operating on battery power Although the battery is connected to the CB10 control box it has exhausted its battery power Reconnect bed to an AC power outlet as soon as possible and allow battery to charge for 24hr IMPORTANT At this point reliable bed operation cannot be guaranteed although some bed functionality may still be available Exercise caution operating the bed as the bed will cease operation without warning NO INDICATOR LED ILLUMINATION IMPORTANT Bed may NOT operate The bed has been disconnected from an AC power outlet and the battery is disconnected from the CB10 control box Reconnect bed to an AC power outlet and allow battery to charge for 24hr OR The bed has a
12. aised and lowered if the bed is in Trend Reverse Trend it will not lower past its Trendelenburg limit of 15 deck height If the bed is angled level bed by pressing opposite Trend function bed will automatically stop at level position Hint A slight Trendelenburg or Reverse Trendelenburg angle may not be easily visible If the bed appears stuck at approximately 15 briefly press and hold the Trend button to achieve a slight bed angle then hold the rev Trend button until the bed automatically stops at level Then lower the bed To reset spirit ultra low bed 1 Make sure that the bed is plugged in and switched on 2 Check that there are no lock out lights showing on the footboard control panel 3 On the side rail control press the BED DOWN button and keep pressing for about 30 seconds or as long as it takes for the bed to go down to it s lowest position 4 When the bed has gone down to it s lowest position keep pressing for a further 30 seconds 5 The bed should now work normally PAGE 17 20 MONTCALM International INFECTION CONTROL Spirit Ultra Low Bed quad side rails headboard and footboard have been treated to kill bacteria that come in contact with these bed surfaces This treatment lasts throughout the life of the bed and is effective against numerous bacteria including MRSA and e coli In addition the detachable mattress deck provides easy and thorough cleaning of the entire surface while t
13. commended that you use a 35 5 900mm wide mattress that is designed to conform to the bed length of 80 2032mm gt D Possible patient ENTRAPMENT Hazard if using non specified mattress patient entrapment may result in an injury Use only a mattress of recommended specifications with this bed e DO NOT use without a special mattress specifically designed to bend and conform to the shape of the bed e DO NOT use a water filled or gel filled mattress on this bed gt GENERAL PRECAUTIONS e Do not use headboards or footboards from other manufacturers e Ensure all deck hinges are properly aligned before raising head or knee sections e Ensure that the headboard and footboard are properly attached to the frame gt This bed is rated to 35 stone 227kg DO NOT overload the bed The combined weigh of patients visitors mattress and bedding must NOT exceed 35 stone 227kg The maximum load on either side rail is 12 stone 77kg gt AT THE INSTALLATION The person supplying and setting up the bed will show staff how it operates All staff that may come into contact with the bed whether nurses cleaners or porters will need to understand how the bed operates A further training session may be required for the above standard to be met and in order to consolidate staff competence REMEMBER TRAINING IN THE USE OF EQUIPMENT IS A LEGAL REQUIREMENT The prerequisites for using the Spirit Ultra Low bed are that it has b
14. e UP position IMPORTANT An audible click should be heard when the head siderail has been completely raised to the UP position as the locking mechanism engages RAISING THE HEAD SIDERAILS Depress the green push button then gently push down on the head siderail The head siderail will first arc towards the head end of the bed then back towards the foot end of the bed as it rotates to the DOWN position IMPORTANT The head siderails will not lock in the DOWN position BED OPERATION CENTRAL LOCK AND STEER SYSTEM Unintended bed movement may occur if bed is left in either of the mobilized positions STEER fa or NEUTRAL Never leave the bed unattended in either the STEER or NEUTRAL positions Do not move the bed until the mobilization system has been activated MODE FUNCTION PEDAL POSITION LOCK a Typical mode used to stabilize the Casters DO NOT lt t bed from shifting This mode swivel or roll a prevents the bed from moving C forward backward or sideways STEER Mode used when attempting to Two head end casters swivel steer the bed in a desired direction Two foot end casters c All caster wheels can still rotate DO NOT swivel lt enabling the bed to move forward All casters roll E or backward NEUTRAL Mode used only to manoeuvre the All casters swivel and roll o bed in a tight area This mode d allows the bed to move forward O backward or sideways SPIRIT
15. e bed Bed retraction procedure is the same as the above except that the footboard bracket and the foot deck extension pan are pushed towards the head end of the bed until contact is made with their respective mechanical stops PAGE 16 20 SPIRIT USER MANUAL VERSION 01 2013 SPIRIT the low bed SPIRIT BED TROUBLESHOOTING GUIDE NOTICE Perform a brief function test on the bed Check all functions on both the staff control pads and the patient control pads PROBLEM FAILURE No functions working on the bed Patients control pad working properly Footboard staff control pad not working Footboard staff control pad is working properly but quad rail control pad not working Bed will not lower all the way Bed Up down Function not working SPIRIT USER MANUAL VERSION 01 2013 RECOMMENDED ACTION 1 Check to ensure bed is plugged in 2 Check wall outlet for power 3 Check mains cable for any damage Check cable connection under lower left side of footboard Lift up footboard and check connection is not damaged Check lockout buttons on footboard pad orange light on lock button prevents the patient control from being used 1 Check to see if the Bed Up Down function is locked out on the footboard 2 Check to see if the bed is in Trendelenburg or Reverse Trendelenburg angle For patient safety bed maintains whatever angle is established by staff as the bed is r
16. e range of mattresses and therapeutic support surfaces to meet the specific needs of your patient see recommended mattress dimensions above SPIRIT USER MANUAL VERSION 01 2013 PAGE 19 20 MONTCALM International the low bed specialist The SPIRIT Ultra Low Bed USER MANUAL GUIDANCE NOTES FOR SAFE USE CE CLASS 1 MEDICAL DEVICE T 01865 409926 F 01865 409948 info montcalmcare co uk www montcalmcare co uk
17. een electrically tested and that the person operating it has had instruction in its use The bed must also have an up to date hospital inspection record SPIRIT USER MANUAL VERSION 01 2013 PAGE 3 20 MONTCALM International gt gt PPP BRB PAGE 4 20 Familiarise yourself with the various functions Care should be taken that there is no wall mounted obstruction to prevent the bed moving vertically Ensure that nothing can get trapped underneath the bed when it is lowered Examples slippers pillows walking sticks etc It is essential that the power cable does not get trapped between moving parts Check before lowering the bed DO NOT allow patients to fall on the bed DO NOT Jump on the bed Each of the preceding impacts can permanently damage either Hi Lo motor resulting in an inoperable bed In the case of an inoperable bed due to a damaged Hi Lo motor remove the bed from service and replace the Hi Lo motor immediately If left unattended a damaged Hi Lo motor could result in patient injury ONLY use original manufacturers replacement parts SPIRIT USER MANUAL VERSION 01 2013 BED POSITIONING BED ELEVATION HI LO FUNCTION To raise the bed press the BED UP arrow on the staff control pad See DIA 10 Release the button when the desired level is reached See DIA 11 To lower the bed press BED DOWN arrow on the staff control pad See DIA 12 Release the button when the desired level is reached
18. he footboard bracket channel Typical both sides SPIRIT USER MANUAL VERSION 01 2013 4 Unlock foot deck extension pan by grasping the chrome handle and sliding the locking mechanism towards the patient left side of the bed to theunlocked position green unlocked icon PAGE 15 20 MONTCAL International 5 Grasp the chrome handle as shown at right Gently 6 Lock foot deck extension pan by grasping the and smoothly pull away from the head end of the bed chrome handle and sliding the locking until the foot deck extension pan contacts its mechanism towards the patient right side of mechanical stops the bed to the locked position red locked icon Possible PATIENT ENTRAPMENT Hazard could occur if the mattress is not securely located fax and retained on the mattress deck by the four corner mattress keepers NEVER perform a bed extension retraction with a patient on the bed NEVER place a patient on the bed if the mattress is not properly located and retained on the mattress deck by the four corner mattress keepers Possible UNEXPECTED MOTION could occur if the slide lock is not in the lock position fax and the mattress deck is articulated from the horizontal position When the bed is in either the extended or retracted position the clamping knob fasteners MUST be fully engaged and the slide lock MUST be in the lock position prior to placing a patient on the bed and or allowing a patient to return to th
19. he fiber composite material reduces moisture build up CLEANING ADVICE The SPIRT bed is manufactured to IPX4 this is moderate resistance to ingress of liquids and dust The bed can be washed in a low pressure spray booth All normal hospital cleaners can be used e g 1 10 000 chlorine DO NOT USE PHENOL BASED CLEANERS ALWAYS DISCONNECT THE POWER BEFORE CLEANING If you require any further advice please call Montcalm International on 01865 409926 PAGE 18 20 SPIRIT USER MANUAL VERSION 01 2013 SPECIFICATIONS e Sleep surface deck length 80 2030mm Sleep surface deck to floor high position 34 865mm Sleep surface deck to floor low position 8 25 200mm e Overall sleep surface width with mattress 36 9 15mm SPIRIT the low bed Recommended weight capacity 35 stone 227kgs e Recommended mattress thickness 6 152mm e Recommended mattress size 900mm x 2032mm e Overall length 93 5 2375mm e Overall sleep surface width without mattress 35 5 200mm Overall width with quad rails 40 1020mm FEATURES LOW BED HEIGHT Prevents patient falls and related injuries Help risk free manual handling DETACHABLE MATTRESS DECK Fibre composite deck completely detaches for thorough sanitization e Standard 5 year warranty FOOTBOARD STAFF CONTROL PANEL e 5 function panel is located on the footboard for staff access e Includes lockout buttons for each and all patient controls
20. t from the potential of falling from the bed IMPORTANT An audible click should be heard when each siderail assembly has been completely rotated into the UP position as the locking mechanism engages The DOWN position the Quad siderails fully rotate out of the way to provide unimpeded and unassisted patient ingress to and egress from the bed and also enables patient transfer by staff IMPORTANT The siderails will not lock in the DOWN position RAISING THE FOOT SIDERAILS Gently rotate the foot siderail to the UP position The foot siderail will first arc toward the foot end of the bed then back towards the head end of the bed as it rotates to the UP position IMPORTANT An audible click should be heard when the foot siderail has been completely raised to the UP position as the locking mechanism engages LOWERING THE FOOT SIDERAILS Depress the green push button then gently push down on the foot siderail The foot siderail will first arc towards the foot end of the bed then back towards the head end of the bed as it rotates to the DOWN position IMPORTANT The foot siderails will not lock in the DOWN position PAGE 12 20 SPIRIT USER MANUAL VERSION 01 2013 SPIRIT the low bed RAISING THE HEAD SIDERAILS Gently rotate the head siderail to the UP position The head siderail will first arc toward the head end of the bed then back F towards the foot end of the bed as it rotates to th
21. the bed press the KNEE UP arrow release button when the desired level is reached To lower the knee section of the bed press the KNEE DOWN arrow release button when the desire level is reached It is recommended that you de activate auto contour on the staff control pad when patient has full control of head and foot profile functions PAGE 10 20 SPIRITTM USER MANUAL VERSION 01 2013 SPIRIT the low bed QUAD RAIL STAFF CONTROL PAD HEAD PROFILE ELEVATION FUNCTION To raise the head section of the bed press the HEAD UP arrow release the button when the desired level is reached To lower the head section of the bed press the HEAD DOWN arrow release button when the desired level is reached KNEE PROFILE ELEVATION FUNCTION To raise the knee section of the bed press the KNEE UP arrow release button when the desired level is reached To lower the knee section of the bed press the KNEE DOWN arrow release button when the desired level is reached BED HIGH LOW ELEVATION FUNCTION To raise the bed press the BED UP arrow release button when the desired level is reached To lower the bed press BED DOWN arrow release button when the desire level is reached SPIRIT USER MANUAL VERSION 01 2013 PAGE 11 20 SSs MONTCALM International OPERATION OF THE QUAD SIDERAILS In the UP position the Quad siderails provide positive patient location and support helping to protect the patien
22. vailable to operate the bed The icons will illuminate respective of the source of power the operation of the ires charging circuit and the level of battery power The battery is continuously charged when connected to the CB10 control box and the bed is plugged into an AC power outlet If the battery voltage drops below 18VDC battery power will b cea disrupted to prevent further discharge which could impact the battery s ability to fully recharge When the bed is plugged back into an AC power outlet battery power will be automatically restored INDICATOR LED IS SOLID GREEN Bed is connected to an AC power outlet and operating on AC power The battery is connected to the CB10 control box and is fully charged Bed is ready to operate on battery power if required This is the optimum operating condition for the bed INDICATOR LED IS FLASHING GREEN Bed is connected to an AC power outlet and operating on AC power The battery is connected to the CB10 control box but is currently recharging INDICATOR LED IS ALTERNATING FLASHING GREEN AND RED IMPORTANT Bed may not reliably operate on battery power if required Bed is connected to an AC power outlet and operating on AC power The battery is connected to the CB10 control ies but not holding proper charge Service bed and or replace battery immediately OR The battery is not connected to the CB10 control box Connect battery to CB10 and allow battery to charge for 24hr INDICA
Download Pdf Manuals
Related Search