Shogun DJ G-100
Contents
1. ET ee ETS fae eo Dip Switch Position DMX Address 11 DMX Channels Channel 1 Mode Laser Off 11 120 Dynamic Patterns 121 250 Static Patterns 251 255 Reset Channel 2 Pattern Selection 0 255 Num n Static Dynamic Channel 3 X Position 0 255 Adjust X Position Channel 4 Y Position 0 255 Adjust Y Position Channel 5 Scanning Speed 0 255 From Fast 0 to Slow 255 Channel 6 Dynamic Pattern Play Speed 0 255 From Fast 0 to Slow 255 Channel 7 Static Patterns Pattern Size 0 255 From Fast 0 to Slow 255 12 Always use a new Q tip or cotton swab for each pass Use only Reagent grade acetone or 90 isopropyl alcohol Do not use too much force otherwise the mirror may break Always turn the power off before cleaning Let mirror dry before using the laser again Direction of Dirt on mirrors cleaning Rotate the cotton Q tip Maintenance The Showtec Shogun DJ G 100 requires almost no maintenance However you should keep the unit clean Otherwise the fixture s light output will be significantly reduced Disconnect the mains power supply and then wipe the cover with a damp cloth Do not immerse in liquid Carefully wipe both mirrors clean with glass cleaner and a soft cloth Do not use alcohol or solvents The m2. Empey Shogun DJ G 100 ORDERCODE 32001 SHOWELECTRONICS FOR PROFESSIONALS Congratulations You have bought a great innovative product from Showtec The Showtec Shogun DJ G 100 brings excitement to any venue Whether you want simple plug amp play action or a sophisticated DMX show this product provides the effect you need You can rely on Showtec for more excellent lighting products We design and manufacture professional light equipment for the entertainment industry New products are being launched regularly We work hard to keep you our customer satisfied For more information iwant showtec info You can get some of the best quality best priced products on the market from Showtec So next time turn to Showtec for more great lighting equipment Always get the best with Showtec Thank you Showtec Showtec Shogun DJ G 100 Product Guide Warning __ _____ __ _ _ _ _________ _____ _ __ __ Safety instructions Operating Determinations Description e Features and Overview e e EOS o E AC 17 Set Up and Operation 5 One Shogun G 100 Stand alone mode One Shogun G 100 Sound Active One Shogun G 100 Auto MODE den ee dense ame mn sas Multiple Shoguns G 100 Master Slave Multiple Shoguns G 100 DMX Control DMX D DSC RES R EEE ro roo cies DMX Quick Reference Chart DMX Channels Maintenance
3. Replacing the Fuse Troubleshooting No Light No Response to DMX Proquct gt DOC AU OMA S gt a O gt ON 11 12 13 13 14 14 15 WARNING LASER y TS da riu CAUTION EYEDAMAGES AN NEVER LOOK DIRECTLY INTO THE LIGHTSOURCE NEVER PROJECT A SINGLE LASER POINT CAUTION Keep this device away from rain and moisture Unplug mains lead before opening the housing FOR YOUR OWN SAFETY PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOUR INITIAL START UP SAFETY INSTRUCTIONS Every person involved with the installation operation and maintenance of this device has to be qualified follow the instructions of this manual CAUTION Be careful with your operations With a dangerous voltage you can suffer a dangerous electric shock when touching the wires Before your initial start up please make sure that there is no damage caused by transportation Should there be any consult your dealer and do not use the device To maintain perfect condition and to ensure a safe operation it is absolutely necessary for the user to follow the safety instructions and warning notes written in this manual Please consider that damages caused by manual modifications to the device are not subject to warranty This device contains no user serviceable parts Refer servicing to qualified technicians only IMPORTANT The manufacturer will
4. The pins 1 Earth 2 Signal 3 Signal 3 Link the units as shown in figure 4 Connect a DMX signal cable from the first unit s DMX out socket to the second unit s in socket Repeat this process to link the second third and fourth units 4 Set DMX dip switches as follows See Dip Switch setting page 10 Shogun DJ G 100 DMX Dip Switches ON Unit 1 Master Either Sound Active All dipswitches OFF or Auto Mode Dipswitch 12 ON Unit 2 Slave Dipswitch 10 ON Unit 3 Slave Dipswitch 10 ON Unit 4 Slave Dipswitch 10 ON 5 Supply electric power Plug the end of the mains power cord into proper electric power supply sockets Multiple Shoguns DJ G 100 DMX Control 1 Fasten the effect light onto firm trussing Use a 30 kg rated or stronger C clamp bolted onto the Showtec Shogun bracket Leave at least 0 5 meter on all sides for air circulation 2 Use a 3 p XLR cable to connect the Shoguns and other devices The pins 1 Earth 2 Signal 3 Signal 3 Link the units as shown in figure 4 Connect a DMX signal cable from the first unit s DMX out socket to the second unit s in socket Repeat this process to link the second third and fourth units 4 Set DMX dip switches as follows See Dip Switch setting page 10 Shogun DJ G 100 Address Value DMX Dip Switches ON Unit 1 1 1 and for DMX 10 and 12 Unit 2 8 4 and for DMX 10 and 12 Unit 3 15 1 2 3 4 and for DMX 10 and 12 Unit
5. Remote Interlock Connector 11 DMX signal connector OUT 8 Sound Sensitivity control 12 IEC Power Connector Fuse 2A 250V 9 Key System 13 DMX signal connector IN Remote Interlock Connector Use a DB9 connector to connect to the Remote Interlock which stops the beam being emitted once the connection loop has been opened Key System When the key is locked the unit stops emitting the laserbeam but keeps the power on and the steppers keep working Only when the key is turned after 15 seconds the projector starts emitting the laserbeam 5 seconds before emitting there is a rattling sound Set Up and Operation Follow the directions below as they pertain to your preferred operation mode Remove the protection cover from the front of the laser When the laser is not in use please replace the cover to protect the laser Before plugging the unit in always make sure that the power supply matches the product specification voltage Do not attempt to operate a 120V specification product on 230V power or vice versa The laser will only work between 15 35 C After 3 hours working you must shut off the laser and let the laser diode cool off for 30 minutes otherwise the laser could be damaged and the warranty becomes void Always disconnect from electric mains power supply before cleaning or servicing Damages caused by non observance are not subject to warranty One Shogun DJ G 100 Stand alone There are 4 possibilities Stand Alon
6. 4 22 1 4 5 and for DMX 10 and 12 5 Supply electric power Plug the end of the mains power cord into proper electric power supply sockets Do so for all units and the controller You can control up to 32 Shogun devices in Master Slave Mode DMX 512 DMX Set up Master Slave Set up Fig 4 Note Link all DMX cables and set dip switches before connecting electric power 6 Do not supply power before the whole system is set up and connected properly Design your show according to your DMX controller functions After every new dipswitch setting you have to disconnect the power and then turn the power on to activate the new dipswitch setting DMX Dip Switch Setting DMX products must have their own address to receive DMX signals Addresses on the Showtec Shogun DJ G 100 are set by flipping the appropriate DMX dip switches A standard DMX address for a Showtec Shogun DJ G 100 which has 7 channels is as follow Shogun DJ G 100 Address Value DMX Dip Switches ON Unit 1 1 1 and for DMX 10 and 12 Unit 2 8 4 and for DMX 10 and 12 Unit 3 15 1 2 3 4 and for DMX 10 and 12 Unit 4 22 1 4 5 and for DMX 10 and 12 Explanation Since each unit has 7 channels each address advances 7 values See Address Value above Once address values are determined set the appropriate DMX dip switches on each unit Example 1 If you want to give a Shogun DMX address133 you first have to find the number 133
7. cord e Make sure that the device is not exposed to extreme heat moisture or dust e sure that the available voltage is not higher than stated on the rear panel e Make sure that the power cord is never crimped or damaged Check the device and the power cord from time to time e If device is dropped or struck disconnect mains power supply immediately Have a qualified engineer inspect for safety before operating e If the device has been exposed to drastic temperature fluctuation e g after transportation do not switch it on immediately The arising condensation water might damage your device Leave the device switched off until it has reached room temperature e If your Showtec device fails to work properly discontinue use immediately Pack the unit securely preferably in the original packing material and return it to your Showtec dealer for service e For adult use only Lighteffect must be installed out of the reach of children Never leave the unit running unattended e For replacement use fuses of same type and rating only e The user is responsible for correct positioning and operating of the laser The manufacturer will not accept liability for damages caused by the misuse or incorrect installation of this laser e This device falls under protection class Therefore it is essential to connect the yellow green conductor to earth The laser will only work between 15 35 C After 3 hours working you must shut o
8. meant to help solve simple problems If a problem occurs carry out the steps below in sequence until a solution is found Once the unit operates properly do not carry out following steps If the light effect does not operate properly refer servicing to a technician Response Suspect three potential problem areas the power supply the laser the fuse 1 Power supply Check that the unit is plugged into an appropriate power supply 2 The laser Return the device to your Showtec dealer 3 The fuse See page 13 for replacing the fuse No Response to DMX Response Suspect the DMX cable or connectors a controller malfunction a light effect DMX card malfunction 1 Check the DMX cable Unplug the unit change the DMX cable then reconnect to electrical power Try your DMX control again 2 Determine whether the controller or laser effect is at fault Does the controller operate properly with other DMX products If not take the controller in for repair If so take the DMX cable and the light effect to a qualified technician 14 Product Specification Model Showtec Shogun DJ G 100 Voltage 240V 50Hz CE Fuse 2A 250V Dimensions 390x285x135mm LxWxH Weight 5 kg Operation and Programming DMX Channels 7 Signal input 3 pin XLR male Signal output 3 pin XLR female DMX control via standard DMX controller Laser 100 mW green Laser 532nm Minimum distance Minimum distance from flammable surfaces 0 5m Minimum dist
9. ance to lighted object 0 8m Design and product specifications are subject to change without prior notice 15 2006 Showtec
10. e Sound active mode Master Auto Mode Master DMX 1 Fasten the Shogun onto firm trussing Leave at least 0 5 meter on all sides for air circulation 2 Plug the cord into a proper electric power supply socket 0 o 1 2 34 5 6 7 10111 12 Sound Active _ Auto Mode _ Master Sound JON Master Auto ON TON ee eje e ON eee DMX Mode Set DMX ADDRESS ON Mode __ 1 17 1 _ Turn on the music If Dip switches are all to 0 then the fixture will react to the beat of the music See page 10 for Dipswitch settings After every new dipswitch setting you have to disconnect the power and then turn the power on to activate the new dipswitch setting You can use the Audio sensitivity knob on the back of the Shogun to adjust the sensitivity reaction to the music Auto Mode If Dip switches are set to 1000000000 then the fixture will play all pre programmed patterns Multiple Shoguns DJ G 100 Master Slave 1 Fasten the effect light onto firm trussing Use a 30 kg rated or stronger C clamp fastened onto the Shogun Leave at least 1 meter on all sides for air circulation 2 Use a 3 p XLR cable to connect the Shoguns and other devices
11. e Product Model Number Serial Number Date of Manufacturing Laser Light Warning Label Warranty Void Label and Interlocked Housing Label Model Serial Number Date of Manulacure user soraceable carts inside EE Ls his Bodine conto wiih FOA 21 100 1040 and subsequent aser Notices OPERATING DETERMINATIONS This device is not designed for permanent operation Consistent operation breaks will ensure that the device will serve you for a long time without defects The minimum distance between light output and the illuminated surface must be more than 0 8 meter The maximum ambient temperature ta must never be exceeded If this device is operated in any other way than the one described in this manual the product may suffer damages and the warranty becomes void Any other operation may lead to dangers like short circuit burns electric shock lamp explosion crash etc You endanger your own safety and the safety of others Rigging Please follow the European and national guidelines concerning rigging trussing and all other safety issues Do not attempt the installation yourself Always let the installation be carried out by an authorized dealer Procedure e If the laser is lowered from the ceiling or high joists professional trussing systems have to be used Use a clamp to mount the laser with the mounting bracket to the trussing system e The laser must never be fixed swinging freely in the r
12. ff the laser and let the laser diode cool off for 30 minutes otherwise the laser could be damaged and the warranty becomes void e Repairs servicing and electric connection must be carried out by a qualified technician e WARRANTY Till one year after date of purchase CAUTION AVOID EXPOSURE TO BEAM Avoid direct eye contact with laser light Never intentionally expose your eyes or others to direct laser radiation Compliance Statement Your Shogun Laser has been designed to comply with FDA and IEC Standards for it classification The Shogun is a Class IIIB laser product Laser Safety and Compliance Information The Shogun is manufactured to comply with the IEC 60825 1 and in accordance with U S Food and Drug Administrations FDA Standards Listed under FDA Document 21 CFR 1040 and subsequent laser notices Product Classification and Manufacturing Label Identification Laser Classification Class IIIB Laser medium wavelength 532 nm Green Output 100mW Cooling TE Cooling CAUTION The use of corrective eye wear or optics for viewing at distances such as telescopes or binoculars within a distance of 100mm may pose an eye hazard This laser product is a Class IIIB laser and has an Interlocked housing There are no user serviceable parts inside Tampering or WARRANTY VOID removing warranty seals will void your products limited seal is broken or has been tampered with wa rranty Manufactured for Combo label with th
13. in the DMX Chart 2 Then look at the left side Dip Switches 1 5 horizontally from 133 In the Table you ll see 1 ON 2 OFF 3 ON 4 OFF 5 OFF 3 Finally look at the upper side of the table Dip Switches 6 9 vertically from 133 In the Table you ll see 6 OFF 7 OFF 8 ON 9 OFF DMX Address Quick Reference Chart Pa Pee Poe Ps Po De 10 DMX Address Quick Reference Chart Dip Switch Position e o Jo ll mor 1 Te a To iw om ase oe Po oe paper 2 Pann on ost 22 Pe ase on Ps Par 2 or EN EEE ES Pa 2 06 o a e TE Y e o DEN EN EE EN EN a as an oe an EN
14. irrors will require regular cleaning as smoke fluid tends to build up residues reducing the light output quickly Keep connections clean Disconnect electric power and then wipe the DMX and audio connections with a damp cloth Make sure connections are thoroughly dry before linking equipment or supplying electric power The following points have to be considered during the inspection 1 All screws used for installing the device or parts of the device have to be tightly connected and must not be corroded 2 There may not be any deformations on housings fixations and installation spots 3 The electric power supply cables must not show any damages or material fatigue Replacing the Fuse Power surges short circuit or inappropriate electrical power supply may cause a fuse to burn out If the fuse burns out the product will not function whatsoever If this happens follow the directions below to do so 1 Unplug the unit from electric power source 2 Insert a screwdriver into the slot in the fuse cover Turn the screwdriver to the left at the same time gently push a bit Turn and Push The fuse will come out 3 Remove the used fuse If brown or unclear it is burned out 4 Insert the replacement fuse into the holder where the old fuse was Reinsert the fuse cover Be sure to use a fuse of the same type and specification See the product specification label for details 13 Troubleshooting No Light This troubleshooting guide is
15. not accept liability for any resulting damages caused by the non observance of this manual or any unauthorized modification to the device e Never unscrew the housing e Never aim the laser beam at people or animals e Never let the power cord come into contact with other cables Handle the power cord and all connections with the mains with particular caution e Never remove warning or informative labels from the unit e Never use anything to cover the ground contact e Never look directly into the light source 2 Never leave any cables lying around Do not insert objects into air vents Do not connect this device to a dimmerpack Do not switch the device on and off in short intervals as this would reduce the lamp s life Do not shake the device Avoid brute force when installing or operating the device Only use device indoor avoid contact with water or other liquids Only operate the device after having familiarized with its functions Avoid flames and do not put close to flammable liquids or gases Always check the regulations when using a class IIIB laser product Always check and position the laser before anybody enters the room when the laser is facing an area with people Always allow free air space of at least 50 cm around the unit for ventilation Always disconnect power from the mains when device is not used before cleaning Only handle the power cord by the plug Never pull out the plug by tugging the power
16. oom e The installation must always be secured with a safety attachment e g an appropriate safety net or safety cable e When rigging derigging or servicing the laser always make sure that the area below the installation place is blocked and staying in the area is forbidden Improper installation can cause serious damage to people and property Proper Usage Safety and Compliance Information According to FDA Regulations you should operate this product as stated on the left 2 5meter Connection with the mains Connect the device to the mains with the power plug Always pay attention that the right color cable is connected to the right place Cable Pin internationai BROWN FASE BLUE YELLOW GREEN EARTH Make sure that the device is always connected properly to the earth Description of the device Features The Showtec Shogun DJ G 100 is a laser effect with a high output and great effects 100 mW green laser DMX control via standard DMX controller 200 pre programmed effects 7 DMX control channels required Sound controlled built in microphone e Fuse 2A 250V Overview Frontside Fig 2 1 Power LED 2 Laser indicator LED 3 Microphone 4 Sound Active LED 5 DMX indicator LED Backside Fes ma gt Sound T gt i men 1 678 9101112 13 Fig 3 6 Dip Switches 10 Power ON OFF 7
Download Pdf Manuals
Related Search