User Manual
Contents
1. Graphics 6 14 10 5303 NOTE This document refers to systems containing the following Intel chipsets processors Intel R Pentium R Processor lt 1 Step 2 Click Next to continue Intel Graphics Media Accelerator Driver Intel Graphics Media Driver Welcome to the Setup Program This setup program will install the Following components Intel Graphics Media Accelerator Driver It is strongly recommended that you exit all programs before continuing Click Next to continue WSBC Q450 User Manual 47 Step 4 Read the License Agreement and click Yes to continue Intel Graphics Media Accelerator Driver Intel Graphics Media Accelerator License Agreement You must accept all of the terms of the license agreement in order to continue the setup program Do you accept the terms INTEL SOFTWARE LICENSE AGREEMENT OEM IHV ISV Distribution Single User IMPORTANT READ BEFORE COPYING INSTALLING OR USING Do not use or load this software and any associated materials collectively the Software until you have carefully read the Following terms and conditions By loading or using the Software you agree to the terms of this Agreement IF you do not wish to so agree do not install or use the Software Please Also Note TF you are an Original Equipment Manufacturer OEM Independent Hardware Vendor IHV or Independent Software Vendor 12. oe o AUDIO2 CD NR o 100 JCOM2_CF6 SATA5 SATA4 COM1 m COM3 J5VSB feral e and L JCF JSPI DV1 H 0000000000 DIMM3 P o gt gt e 4PIN DIMM1 E sua WOL SYSFAN 2 WSBC Q450 User Manual 7 MINI_PCI E WSBC Q450 User Manual JCF Compact Flash Master Slave Select Function Master Slave Default Jumper 3 3 Setting 2 2 1 1 JCMOS1 CMOS Clear Function Normal Operation Default Clear CMOS Contents Jumper Setting 3 3 2 2 1 1 JCOM2 CFG COM RS 232 RS 422 RS 485 Select 1 2 Pin No 5 6 11 13 12 14 3 4 9 11 10 12 1 2 9 11 10 12 1
3. DVMT Mode DVMT Dynamic Video Memory Technology allowing the system to dynamically allocate memory resources according to the demands of the system at any point in time that improve efficiency of the memory allocated to either system or graphics processor Total GFX Memory Select Total GFX Memory 128MB 256MB or MAX For Win XP the MAX Value is base on system memory size 512MB for 1GB DRAM 768MB for 1 5GB to 2GB 1GB fro above 2GB WSBC Q450 User Manual 23 2 5 Integrated Peripherals Phoenix AwardBIOS CMOS Setup Ulility Integrated Peripherals OnChip IDE Device Press Enter Item Help Onboard Device Press Enter Super IO Device Press Enter Menu Leve SecondlO Device Press Enter USB Device Setting Press Enter N lt Move EnterSelect PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults WSBC Q450 User Manual 24 OnChip IDE Device Press lt Enter gt to set IDE and SATA device configuration Phoenix AwardBIOS CMOS Setup Utility OnChip IDE Device IDE HDD Block Mode IDE DMA transfer access IDE Primary Master PIO IDE Primary Slave PIO IDE Primary Master UDMA IDE Primary Slave UDMA On chip Secondary PCI IDE IDE Secondary Master PIO IDE Secondary Slave PIO IDE Secondary Master UDMA IDE Secondary Slave UDMA SATA Mode LEGACY Mode Support i Move Enter Select IPU PD Value F6 Fail Safe Default
4. respective GPIO port is programmed as an output port Value of Output Data Input Data If a port is assigned to be an output port then its respective bit can be read written If a port is assigned to be an input port then its respective bit can be read only Note DIO INO DIO IN1 DIO IN2 DIO IN3 are programmed as Inputs by BIOS default Parameter Conditions VinH min 1 857V VinL max 0 525V Rated Vin 8V 12V NC Status High by Default Attention If DIO INO DIO IN1 DIO IN2 DIO INS are programmed as Output signal they can only offer a normal signal transfer NOT amplified signals Parameter Conditions VoutH 3 3V thru 10k VoutL OV thru 1k DIO OUTO DIO OUT1 DIO OUT2 DIO OUT3 are fixed as Outputs by BIOS Parameter Conditions Open drain buffer Power on default Open Driving Capacity max 100mA continue WSBC Q450 User Manual 58
5. Time hh mm ss 11 28 10 Menu Level IDE Channel 0 Master None IDE Channel 0 Slave None IDE Channel 2 Master None IDE Channel 2 Slave None IDE Channel 3 Master None Video VGA Halt On All But Keyboard Base Memory 639K Extended Memory 1011712K Total Memory 1012736K N gt lt Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Date IDE Channel 3 Master Set system date Press lt Enter gt for IDE device automatic detection Time Set system time Video Select Video device type IDE Channel 0 Master Slave Press lt Enter gt for IDE device automatic Halt on detection Select stop procedure or ignore when error detected during POST Power On IDE Channel 2 Master Slave Self Test Press lt Enter gt for IDE device automatic detection WSBC Q450 User Manual 20 2 3 Advanced BIOS Features Phoenix AwardBIOS CMOS Setup Ulility Advanced BIOS Features CPU Feature gt Hard Disk Boot Priority Virus Warning CPU L3 Cache Quick Power On Self Test First Boot Device Second Boot Device Third Boot Device Boot Other Device Boot Up NumLock Status Gate A20 Option Typematic Rate Setting Security Option MPS Version Control For OS Os Select For DRAM 64MB Report No FDD For WIN 95 Small Logo EPA Show Enter Select M gt lt Move F5 Previous Valu
6. Pin121 128 to be GPIO port outp 0x002E 0x29 outp 0x002F inp 0x002F 0x01 WSBC Q450 User Manual 56 Select Logic Device 7 outp 0x002E 0x07 outp 0x002F 0x07 Active Logic Device 7 outp 0x002E 0x30 outp Ox002F 0x01 Select Inversion Mode outp 0x002E OxF2 outp 0x002F inp 0x002F amp 0 3 Inversion Register amp 0xC3 Select I O Mode outp 0x002E 0760 outp 0x002F inp 0x002F amp 0 3 I O Selection Register amp 0xC3 Access GPIO ports outp 0x002E OxF1 outp 0x002F inp 0x002F amp 0x3C Output Data amp 0xC3 or Input Data inp 0x002F Exit Extended Function Mode outp 0x002E OxAA Definitions of Variables Each bit in the lower nibble of each Register represents the setting of a GPIO port Super IO Pin Bit GPIO DIO 128 0 GPIO DIO Out0 127 1 GPIO DIO Out1 126 2 GPIO DIO In0 125 3 GPIO DIO In1 124 4 GPIO DIO In2 123 5 GPIO DIO In3 122 6 GPIO DIO Out2 121 7 GPIO DIO Out3 WSBC Q450 User Manual 57 Value of Inversion Register When set to a 1 the incoming outgoing port value is inverted When set to a 0 the incoming outgoing port value is the same as in Data Register Value of I O Selection Register When set to a 1 respective GPIO port is programmed as an input port When set to a 0
7. Setting Press lt Enter gt to select USB device configuration Phoenix AwardBIOS CMOS Setup Ulility USB Device Setting USB 1 0 Controller Enabled Item Help USB 2 0 Controller Enabled USB Operation Mode High Speed USB Keyboard Function Enabled USB Mouse Function Enabled USB Storage Function Enabled USB Mass Storage Device Boot Setting N lt Move EnterSelect PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults WSBC Q450 User Manual 31 2 6 Power Management Setup Phoenix AwardBIOS CMOS Setup Ulility Power Management Setup ACPI Function Enabled DEBET ACPI Suspend Type S1 POS LAOUER Soft Off by PWR BTTN Instant Off EU Wake Up by PCI card Disabled Power On by Ring Disabled Resume by Alarm Disabled X Date of Month Alarm 0 X Time hh mm ss Alarm O gt PCI Express PM Function Press Enter N gt lt Move EnterSelect PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults ACPI Function Select Advanced Configuration and Power Management Enabled Disabled ACPI Suspend Type Select S1 POS type Soft Off by PER BTTN Select power button function Instant off Press power button will power off instantly Delay 4 Sec Press power button 4 second to power off C Wake Up by
8. this computer later Click Finish then remove any installation media From the drives WSBC Q450 User Manual 45 3 2 Net Framework Step 1 Click Install to continue Microsoft NET Framework 3 0 Setup Microsoft welcome to Setup net Fra mewo rk Accept the terms of the License Agreement to continue Microsoft NET Framework 3 0 End User License Agreement sure to carefully read and understand all of the rights and restrictions described in the ei 1 OIDO NOT ACCEPT the terms of the License Agreement Send anonymous information about my setup experiences to Microsoft Corporation For more information click Data Collection Policy A Note system reboot may be necessary during installation Step 2 Click Exit to complete setup Microsoft Framework 3 0 Setup Setup Complete net Fra mewo rk Microsoft NET Framework 3 0 has been installed successfully It is highly recommended that you download and install the latest service packs and security updates for this product For more information see Windows Update WSBC Q450 User Manual 46 3 3 Intel Graphic Media Accelerator Driver Step 1 Click Next to continue lt Intel R Chipset Graphics Driver Software InstallShield Wizard A Production Version Releases Microsoft Windows xP Package 107289 Display Audio Driver 5 12 0 3069 Legacy Audio 5 10 0 1049 October 06 2010
9. 5 this complete LICENSE AGREEMENT applies If you are an End User then only Exhibit 4 the INTEL SOFTWARE LICENSE AGREEMENT Yes tallation Frameiworl Step 5 Click Next to continue Intel Graphics Media Accelerator Driver Intel Graphics Media Driver Readme File Information Production Version Releases Microsoft Windows Package 107289 Graphics 6 14 10 5303 Display Audio Driver 5 12 0 3069 Legacy Audio 5 10 0 1049 v Cancel tallation Frameworl WSBC Q450 User Manual 48 Step 6 Click Next to continue Intel Graphics Media Accelerator Driver Intel Graphics Media Accelerator Setup Progress Please wait while the Following setup operations are performed Copying File C Program Files Intel Intel R Graphics Media Accelerator Driver uninstall th TH Copying File C Program Files Intel Intel R Graphics Media Accelerator Driverjuninstall tr TRi Copying File C Program Files Intel Intel R Graphics Media Accelerator DriverYuninstallltr TR Copying File C Program Files Intel Intel R Graphics Media Accelerator Driver uninstall zh Ch Copying File C Program Files Intel Intel R Graphics Media Accelerator Driver uninstall zh ch Copying File C Program Files InteliIntel R Graphics Media Accelerator Driver uninstall zh Ty Copying File C Program Files Intel Intel R Graphics Media Accelerator Driver uninstall zh T Copying File C WINDOWS system32 diFxa
10. 9 21 20 22 17 19 18 20 23 24 Function RS 232 Default RS 422 RS 485 i aud 24 nu 24 23 Setting 210011 2 1 L WSBC Q450 User Manual 9 JCOM2 CFG COM2 RS 232 RS 422 RS 485 Select 2 2 Pin No 7 8 15 16 7 8 Not recommended Function RS422 TXD Pair RS422 RXD Pair RS485 Data Pair 100Ohm Termination 100Ohm Termination 100Ohm Termination dumper 24 23 23 24 23 Setting EH E E El m EN E EN El EN E El El rm m 2 1 2 1 2 E E 1 Function Jumper Setting AT SEL AT ATX Mode Select ATX Mode Default AT Mode 3 2 1 3 2 1 J5VSB 5V connector to 5VSB Select 1 Function 5V connect to 5VSB 5V not connect to 5VSB Default Jumper Setting 3 3 2 2 1 WSBC Q450 User Manual 10 JIDE IDE ATA Mode Select Pin No 1 2 2 3 All Open Function Max UDMA Mode 1 Auto Detect UDMA Min UDMA Mode 2 83MHz Mode Default 66MHz Jumper 3 3 3 Setting 2 2 2 1 1 1 WSBC Q450 User Manual 11 Connector Function ATX_4Pin 5VSB PSON GND signal connect to BP Line In MIC In Line Out Connectors Audio2 Surround Out Center Out Connectors CPUFAN CPU Fan 4Pin Connector DO Digan Connector Digital Video Interface Connector wirh e JFRONT Front Pane
11. D Value F6 Fail Safe Defaults Item Help Auto ESCD Press Enter Press Enter ESC Exit F7 Optimized Defaults F10 Save F1 General Help LCI Resources Controlled By BIOS can automatically configure all the boot and Plug and Play compatible devices If you choose Auto you cannot select IRQ DMA and memory base address fields since BIOS automatically assigns them PCI VGA Palette Snoop Select PCIAVGA Palette Snoop Enabled Disabled 1 Maximum Payload Size Set maximum TLP payload size for the PCI Express devices The unit is byte 2 8 PC Health Status Phoenix AwardBIOS CMOS Setup Ulility PC Health Status Shutdown Temperature Disabled Item Help CPU Warning Temperature Disabled Current CPU Temperature 40 C 104 F Current SYSTEM Temperature 47 C 116 F CPU Fan Speed 2109 RPM System Fan Speed 0 RPM Vcore 1 24 V 12V 12 09 V 1 5 V 1 47 V 1 5 V DRAM 1 46 V 45 V 5 00 V 3 3 V 3 34 V VBAT V 3 04 V 3 3VSB V 3 34 V Smart FAN Setting CPU Smart Fan Temp Disabled System Smart Fan Temp Disabled N gt lt Move EnterSelect PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults 1 Shutdown Temperature If CPU temperature reaches the setting value will automatic shutdown system CPU Warning Temperature If CPU temperature reaches the setting value will beep in DOS mode CPU Smart Fan Temperature S
12. O The System Board provides 4 dedicated output ports and 4 programmable I O ports that can be individually configured to perform a simple I O function Users can configure 4 programmable I O ports to become an input or output port by programming register bit of I O Selection invert port value the setting of Inversion Register has to be made ote Port values can be set to read or write through Data Register Note Only 4 programmable I O ports support Additionally 4 Digital Output ports amplified signals from GPIO ports There are open drain buffers which can offer greater driving capacity up to 100mA For more information about GPIO please refer to Winbond W83627EHF data sheet The related Control Registers of GPIO are all included in the following sample program that is written in C language To ensure a successful accessing to the content of desired Control Register the sequence of following program codes should be step by step run again when each register is accessed There are two PnP I O port addresses that can be used to configure GPIO ports 1 Ox2E EFER Extended Function Enable Register for entering Extended Function Mode EFIR Extended Function Index Register for identifying CR index number 2 Ox2F EFDR Extended Function Data Register for accessing desired CR Below are some example codes which demonstrate the use of GPIOs Enter Extended Function Mode outp 0x002E 0x87 outp 0x002E 0x87 Assign
13. PCI card Select Wake UP by PCI device Enabled Disabled Power On by Ring Select Power on by Ring Indicator signal from Modem WSBC Q450 User Manual 32 Resume by Alarm Set date and time to power on system from soft off state PCI Express PM Function Press Enter to select Wake up by LAN Enabled Disabled Phoenix AwardBIOS CMOS Setup Utility PCI Express PM Function Wake up by Lan Item Help Menu Level N lt Move EnterSelect PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Wake up by Lan Select wake up by Lan Enabled Disabled WSBC Q450 User Manual 33 2 7 PnP PCI Configurations Phoenix AwardBIOS CMOS Setup Ulility PnP PCI Configurations PNP OS Installed No Init Display First Reset Configuration Data Resources Controlled By IRQ Resources DMA Resources PCI VGA Palette Snoop 128 PCI Express relative items Maximum Payload Size l Move Enter Select F5 Previous Values Init Display First Select initial display by PCI or Onboard device Reset Configuration Data Select Enabled to reset Extended System Configuration Data ESCD when you exit BIOS setup utility if you have installed new add on card and the system reconfiguration has caused such a serious conflict that the OS cannot boot WSBC Q450 User Manual PCI Slot Disabled Disabled PU P
14. S setup utility MPS Version Control For OS Select MPS Multiprocessor Specification Version 1 4 to added extended configuration tables to improve support for multiple PCI bus configurations and improve future expandability It is also required for a secondary PCI bus to work without the need for a bridge Select Version 1 1 for older Operating Systems WSBC Q450 User Manual OS Select For DRAM gt 64M Select OS2 only if you are running older version of IBM OS 2 Operating System with greater than 64MB of RAM on the system Otherwise select Non OS 2 setting Report No FDD For WIN 95 If running Windows 95 98 without floppy diskdrive select Enabled to release IRQ6 This is required to pass Windows 95 98 s SCT test If select Disabled BIOS will not report missing floppy drive to Win95 98 1 Small Logo EPA Show Select EPA Environmental Protection Agency Energy Star logo appears during the system boot up process 2 4 Advanced Chipset Features Phoenix AwardBIOS CMOS Setup Ulility Advanced Chipset Features gt PCI Express Root Func Press Enter Item Help Port 80h to PCI On Chip Frame Buffer Size 32MB DVMT Mode Enabled Total GFX Memory 128MB N gt lt EnterSelect PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults On Chip Frame Buffer Size Select share system memory 1MB or 8MB
15. WSBC Q450 PICMG1 0 Full Size SBC User Manual Rev 01 Jul 2011 All rights reserved No part of this publication may be reproduced in any form or by any means without prior written permission of the publisher All trademarks are the properties of the respective owners All product specifications are subject to change without prior notice WSBC Q450 Driver CD Include user s manual 1 x PS2 Y Cable KB and Mouse 1 x LPT Cable with Bracket 1 x 2 Port COM Cable with Bracket 1 x 2 Port USB Cable with Bracket 1 x SATA Cable WSBC Q450 User Manual 2 Contents Chapter 1 Product Information teret tet p 4 1 1 gt eec REP 4 1 2 Feat r S 5 AY T IEEE 7 1 4 dumper uu u 9 1 5 Connector Function Lislt cerent tent 12 1 6 Internal Connector Pin Define sse 13 Chapter 2 BIOS 19 2 1 Men jean capes ccd VS RU 19 2 2 Standard CMOS Features 20 2 3 Advanced BIOS Features 21 2 4 Advanced Chipset Features sees 23 2 5 Integr
16. actory default setting for optimized system operation WSBC Q450 User Manual 38 2 12 Set Supervisor Password Phoenix AwardBIOS CMOS Setup Ulility Standard CMOS Features gt Frequency Voltage Control Advanced BIOS Features Load Fail Safe Defaults Advanced Chipset Features Load Optimized Defaults Integrated Peripherals _ Set Supervisor Password Power Management Setup Set User Password PnP PCI Configura PC Health Status Esc Quit lt gt Select Item F10 Save amp Exit Setup Change Set Disabled Password If set supervisor password it will request typing password to enter BIOS setup utility WSBC Q450 User Manual 39 2 13 Set User Password Phoenix AwardBIOS CMOS Setup Ulility Standard CMOS Features gt Frequency Voltage Control Advanced BIOS Features Load Fail Safe Defaults Advanced Chipset Features Load Optimized Defaults Integrated Peripherals Set Supervisor Password Power Management Setup PnP PCI Configura PC Health Status Esc Quit lt Select Item F10 Save amp Exit Setup Change Set Disabled Password If set user password will request typing password to enter BIOS setup utility and does not allow modifying configuration WSBC Q450 User Manual 40 2 14 Save amp Exit Setup Phoenix AwardBIOS CMOS Setup Ulility Standard CMOS Features gt Frequency Voltage Control Advanced BIOS Features Load Fail Safe Defaults Advanced Chipset Features Load Optimized Def
17. and the ATA bus to allow DMA commands to transfer data at a maximum burst rate of 33 MB s When you select Auto in the four IDE UDMA fields for each of up to four IDE devices that the internal PCI IDE interface supports the system automatically determines the optimal data transfer rate for each IDE device SATA Mode There have three selections in SATA mode B IDE Default B RAID Enable SATA RAID function B AHCI Set this item to enable SATA AHCI function for WinXP SPI IAA driver support AHCI mode LEGACY Mode Support Certain os is not supported under Native mode WSBC Q450 User Manual 26 Onboard Device Phoenix AwardBIOS CMOS Setup Utility Onboard Device Onboard Lan Boot ROM Disabled Item Help ADO Control Enabled N lt Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Onboard Lan Boot ROM Decide whether to invoke the boot ROM of the onboard LAN chip ADO Control Enable Disable Audio control WSBC Q450 User Manual 27 Super IO Device Press lt Enter gt to select Serial Parallel and configuration Phoenix AwardBIOS CMOS Setup Utility Super IO Device Onboard Serial Port 1 Onboard Serial Port 2 UART Mode Select x RxD TxD Active x IR Transmission Delay x UR2 Duplex Mode x Use IR Pins Onboard Parallel Port Parallel Port Mode x EPP Mode Select x EPC Mo
18. ated Peripherals en ma u cea UA pA PU ER NUR 24 2 6 Power Management Setup sse 32 2 7 PnP PCI COhfIQUEatiOns 34 2 8 PC Health oot Mte ER CU 35 2 9 Frequency Voltage Control 36 2 10 Load Fail Safe 06 37 2 11 Load Optimized Defaults sese 38 2 12 Set Supervisor Password sees 39 2 13 Set User PasSWOEQ a too A 40 2 14 Save amp 41 2 15 ExIttWIIROUUSAVIBQ su nero Cutie Pot teet fopra tota tia tud tits 42 Chapter 3 Drivers Installation 2 22 2 4 43 3 1 Intel Chipset Device Software 43 3 2 Net FramewWOEK ooo oet etnies C eee a 46 3 3 Intel Graphic Media Accelerator Driver 47 SAP LAN sci cons 53 3 5 A dio ose 53 Appendix A ree oett Ide too o ER n ses Gere NES 54 Appendpc B dos acc te tdi Sd qd 56 WSBC Q450 User Manual 3 Chapter 1 Product Info
19. aults Integrated Peripherals Set Supervisor Password Power Managem PnP PCI Configu PC Health Status Esc Quit lt gt Select Item F10 Save amp Exit Setup Save Data to CMOS This item confirm save configuration or not before exit BIOS setup utility Press lt Y gt and lt Enter gt to save configuration then reboot system Press N and Enter will back to BIOS setup utility WSBC Q450 User Manual 41 2 15 Exit Without Saving Phoenix AwardBIOS CMOS Setup Ulility Standard CMOS Features gt Frequency Voltage Control Advanced BIOS Features Load Fail Safe Defaults Advanced Chipset Features Load Optimized Defaults Integrated Peripherals Set Supervisor Password Power Managem PnP PCI Configu PC Health Status Esc Quit lt gt Select Item F10 Save amp Exit Setup Abandon all Data This item confirm save configuration or not before quit BIOS setup utility Press lt Y gt and lt Enter gt will not save configuration then reboot system Press lt N gt and lt Enter gt will back to BIOS setup utility WSBC Q450 User Manual 42 Chapter 3 Drivers Installation This chapter introduces driver installation information Please insert the utility CD to CD ROM drive the install menu will appear automatically if the install menu did not list suitable driver of Operate System or did not appear automatically please select corresponding driver of utility CD to install The Windows XP d
20. de Use DMA Watchdog Timer Select 14 lt Enter Select F5 Previous Values Onboard Serial Port 1 Item Help Menu Level 3F8 IRQ4 2F8 IRQ3 Normal Hi Lo Enabled Half IR Rx2Tx2 378 IRQ7 SPP 3 Disabled PU PD Value F10 Save ESC Exit F1 General Help F6 Fail Safe Defaults F7 Optimized Defaults Select serial port 1 address Disabled 3F8 IRQ4 2F8 IRQ3 3E8 IRQ4 2E8 IRQ3 or Auto Onboard Serial Port 2 Select serial port 2 address Disabled 3F8 IRQ4 2F8 IRQ3 3E8 IRQ4 2E8 IRQ3 or Auto UART Mode Select Select UART Mode IrDA ASKIR or Normal Onboard Parallel Port Select onboard parallel port Disabled 378 IRQ7 278 IRQ5 or 3BC IRQ7 WSBC Q450 User Manual 28 Parallel Port Mode Select Parellel Port Mode SPP EPP ECP ECP EPP or Normal Watchdog Timer Select Select Watch dog Disabled or set timer value 10sec 20sec 30sec 40sec 1 min 2min or 4min WSBC Q450 User Manual 29 Second IO Device Phoenix AwardBIOS CMOS Setup Utility Second IO Device Onboard Serial Port 3 3E8h Item Help Onboard Serial Port 4 2E8h Menu Leve N lt Move EnterSelect PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Onboard Serial Port 3 4 Select serial port address WSBC Q450 User Manual 30 USB Device
21. do not wish to so agree do not install or use the Software LICENSES Please Note O1 do not accept the terms in the license agreement Install5rield WSBC Q450 User Manual 50 Step 3 Click Next to continue Intel R Network Connections Setup Options Select the program Features you want installed Install Intel R PROSet For Windows Device Manager Advanced Network Services Intel R Network Connections SNMP Agent Feature Description Drivers For all wired Intel Network Connections Step 4 Click Install to continue 15 Intel R Network Connections InstallShield Wizard Ready to Install the Program The wizard is ready to begin installation Click Install to begin the installation you want to review or change any of your installation settings click Back Click Cancel to exit the wizard WSBC Q450 User Manual 51 Step 5 Click Finish to complete setup ie Intel R Network Connections InstallShield Wizard WSBC Q450 User Manual 52 3 5 Audio Driver Step 1 Click Next to continue Welcome to the InstallShield Wizard for Realtek High Definition Audio Driver saltek High Definition Audio Driver on your computer To Step 2 Click Finish to complete setup P or Audio Driver Realtek efinitic dio Driver Se InstallShield Wizard Complete led Realtek High Definition Audio Driver Before start your compu
22. es CPU Feature Press Enter to select CPU parameter Hard Disk Boot Priority PU PD Value F6 Fail Safe Defaults Press Enter Disabled Enabled Enabled USB CDROM Hard Disk USB FDD Enabled Fast Disabled Setup 1 4 Non OS2 No Disabled F10 Save ESC Exit F7 Optimized Defaults F1 General Help C Quick Power On Self Test Select Quick Power On Self Test Enabled Disabled Press Enter to select Hard Disk boot device priority 1 Virus Warning Select Virus Warning Enabled Disabled CPU L3 Cache Select CPU L3 Cache Enabled Disabled WSBC Q450 User Manual First Second Third Boot Device Select boot device priority Boot Other Device Select Boot Other Enabled Disabled Device 21 Boot NumLock Status Select lt NumLock gt key ON Off when system boot up 1 Gate A20 Option Select Gate A20 controlled by Keyboard controller Normal or Port 92 Fast Typematic Rate Setting Select Typematic Rate Setting Enabled to set Typematic Rate Chars Sec Number of characters repeated in one second Typematic Delay Msec When holding one key set the time between the first and second character displayed Security Option Select security mode Setup Require password to permit BIOS setup utility System Require password to permit boot up and BIO
23. etup CPU Smart FAN temperature System Smart Fan Temp Setup System Smart FAN temperature 2 9 Frequency Voltage Control Phoenix AwardBIOS CMOS Setup Ulility Frequency Voltage Control Spread Spectrum Item Help Menu Level N lt Move EnterSelect PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults L Spread Spectrum Select Spread Spectrum Enabled Disabled WSBC Q450 User Manual 36 2 10 Load Fail Safe Defaults Phoenix AwardBIOS CMOS Setup Ulility Standard CMOS Features gt Frequency Voltage Control Advanced BIOS Features 1080 Fail Safe Defaults Advanced Chipset Features Load Optimized Defaults Integrated Peripherals Set Supervisor Password Power Managem PnP PCI Configu PC Health Status Esc Quit lt Select Item F10 Save amp Exit Setup Load Fail Safe Defaults This item will set configuration for non optimized system operation WSBC Q450 User Manual 37 2 11 Load Optimized Defaults Phoenix AwardBIOS CMOS Setup Ulility Standard CMOS Features gt Frequency Voltage Control Advanced BIOS Features Load Fail Safe Defaults Advanced Chipset Features 1080 Optimized Defaults Integrated Peripherals Set Supervisor Password Power Managem PnP PCI Configu PC Health Status Esc Quit lt gt Select Item F10 Save amp Exit Setup Load Optimized Defaults This item will restore f
24. in No Signal nomo HDMI Ground 1 WSBC Q450 User Manual 14 CD IN CD IN Connector with Wafer header 2 5mm JFRONT Front Panel Connector with Pin header 2 54mm Signal Pin No Signal 2 5V 470 Ohm 4 HDD LED 5VSB 470 Ohm Ground Speaker NC NC Power Switch NC Ground 5V JSPI Serial Peripheral Interface Connector 2 0mm Signal Pin No Signal WSBC Q450 User Manual 15 LPT Parallel Port Connector with Box header 2 54mm Pin No Signal Pin No Signal 6 oom S ps on om 10 Acknowledge Ground Ce i2 PaperEmpty Empty 2 Ground External Keyboard Connector with Wafer header 2 5 KBCLK KBDATA KB MS PS2 Keyboard amp Mouse with Mini DIN Connector Pin No Signal Pin No Signal Gum lt s S SNS WOL PCI card wake on LAN signal 2 0mm Pin No Signal WSBC Q450 User Manual 16 PWR ATX 2x2 Power Connector 4 2mm Pin No Signal 12V 5V In ut Power input for Single Board function 4 2mm 2 Ground 3 Ground USB1 USB1 for IO connector Pin No Signal USB Power 5V USB DATAO USB 04140 USB Ground USB2 3 4 USB2 3 4 Port Connector with Wafer heade
25. installation information Press the Page Down key to view the rest of the File I A NON NN ON UN NN NN NS S NN OS NN ON NN ON S NN S NN S A Product Intel R Chipset Device Software E Release Production Version Version 9 1 1 1025 Target Chipset Intel R 5 Series 3400 Series Chipse Date December 14 2009 ntn ss gt 3 ies WSBC Q450 User Manual 44 Step 4 Click Next to continue Intel amp Chipset Device Software Intel amp Chipset Device Software Setup Progress Please wait while the following setup operations are performed Installing Driver Intel R ICH10 Family USB Universal Host Controller 3467 Version 9 0 0 1005 Installing Driver Intel R ICH10 Family USB Universal Host Controller 3468 Version 9 0 0 1005 Installing Driver Intel R ICH10 Family USB Universal Host Controller 3469 Version 9 0 0 1005 Installing Driver Intel R ICH10 Family USB Enhanced Host Controller 3464 Version 9 0 0 1005 Installing Driver Intel R ICH10 Family USB Enhanced Host Controller 346C Version 9 0 0 1005 Click Next to continue Step 5 Click Finish to complete setup Intel amp Chipset Device Software Intel Chipset Device Software Setup Is Complete You must restart this computer For the changes to take effect Would you like to restart the computer now Yes I want to restart this computer now C I will restart
26. l Connector SPI BIOS tool reflash function LAN1 2 RJ45 LAN Connector L Reserved for debug K Parallel Port Connectors KB External Keyboard Connector KB MS DVI PC PT B PWR4P Power input for Single Board function SATA1 2 3 4 5 6 SATA Connector DIMM1 2 DDR3 DIMM connector USB1 USB1 Port Connectors USB2 3 4 USB2 3 4 Port pin header WSBC Q450 User Manual 12 ATX 4Pin ATX 4 Connector with Wafer header 2 5mm 1 Signal 1 ATX Power OK Pin No Signal Pin No Signal Line In Jack Detect MIC In Jack Detect Line Out Jack Detect 9 Line Out L Audio Ground 11 Line Out R NC AUDIO2 Surround Out Center Out Connectors with Pin header 2 54mm Pin No Signal Pin No Signal SURR Out L 2 SURR Out Jack Detect SURR Out R 4 CEN Out Jack Detect CEN Out 6 Audio Ground LEF Out 8 Audio Ground 9 SPDIF Out 0 Ground 11 5V 2 NC CPUFAN 4Pin FAN Connector Signal Ground Fan Power 12V Speed Sense WSBC Q450 User Manual 13 SYSFAN System FAN connector 3 Pin No Signal Signal DCD RXD TXD DTR RI 5V 12V s Ground NC Pin No Signal Pin No Signal 9 12V 5V 11 Ground NC DVI Digital Video Interface with Box header 1 0 mm 20 PT Pin No Signal P
27. pi dll Deleting Registry Key HKLM SOFTWARE Microsoft Windows CurrentVersion Uninstall HDMI Deleting Registry Key HKLM SOFTWARE Intel IGDI Click Next to continue Step 7 Click Finish to complete setup Intel Graphics Media Accelerator Driver Setup Is Complete You must restart this computer for the changes to take effect Would you like to restart the computer now CO No I will restart this computer later Click Finish then remove any installation media from the drives tallat WSBC Q450 User Manual 49 3 4 LAN Driver Step 1 Click Next to continue T Intel R Network Connections InstallShield Wizard Welcome to the InstallShield Wizard for Intel R Network Connections Installs drivers Intel R PROSet For Windows Device Manager and Advanced Networking Services WARNING This program is protected by copyright law and international treaties Cancel Step 2 Click Next to continue im Intel R Network Connections InstallShield Wizard License Agreement Please read the Following license agreement carefully INTEL SOFTWARE LICENSE AGREEMENT Final License IMPORTANT READ BEFORE COPYING INSTALLING OR USING Do not use or load this software and any associated materials collectively the Software until you have carefully read the following terms and conditions By loading or using the Software you agree to the terms of this Agreement If you
28. r 2 5mm Pin No Signal Pin No Signal S 1 Case Ground ATX 4Pin ATX 4Pin Connector with Wafer header 2 5mm Signal WSBC Q450 User Manual 17 IR IR Connector with Wafer header 2 5mm LPC LPC Connector with Wafer header 2 0mm Pin No Signal 1 LADO 2 PLTRST 6 Gond WSBC Q450 User Manual 18 Chapter 2 BIOS Setup This chapter introduces BIOS setup information Power on or reboot the system board when screen appears message as Press DEL to enter SETUP Press DEL key to run BIOS SETUP Utility Note The BIOS configuration for reference only it may subject to change without prior notice 2 1 Main Menu Please use arrow keys to select item then press Enter key to accept or enter the sub menu Phoenix AwardBIOS CMOS Setup Utility gt Standard CMOS Features gt Frequency Voltage Control Advanced BIOS Features Load Fail Safe Defaults Advanced Chipset Features Load Optimized Defaults Integrated Peripherals Set Supervisor Password Power Management Setup Set User Password PnP PCI Configurations Save amp Exit Setup PC Health Status Exit Without Saving Esc Quit lt gt Select Item F10 Save amp Exit Setup Time Date Hard Disk Type WSBC Q450 User Manual 19 2 2 Standard CMOS Features Phoenix AwardBIOS CMOS Setup Ulility Standard CMOS Features Date mm dd yy 11 2011 Item Help
29. river installation steps are as below 3 1 Intel Chipset Device Software Step 1 Click Next to continue Intel amp Chipset Device Software Intel Chipset Device Software Welcome to the Setup Program This setup program will install the Intel Chipset Device Software onto this computer It is strongly recommended that you exit all programs before continuing E ined WSBC Q450 User Manual 43 Step 2 Read the License Agreement and click Yes to continue Intel Chipset Device Software Intel Chipset Device Software License Agreement You must accept all of the terms of the license agreement in order to continue the setup program Do you accept the terms INTEL SOFTWARE LICENSE AGREEMENT IHV ISV Distribution amp Single User IMPORTANT READ BEFORE COPYING INSTALLING OR LISING Do not use or load this software and any associated materials collectively the Software until you have carefully read the Following terms and conditions By loading or using the Software you agree to the terms of this Agreement IF you do not wish to so agree do not install or use the Software Please Also Note If you are an Original Equipment Manufacturer OEM Independent Hardware Vendor IHY or Independent Software Vendor 15 this complete LICENSE AGREEMENT applies Intel Chipset Device Software Readme File Information Refer to the Readme file below to view the system requirements and
30. rmation This chapter introduces the product features jumper and connector information 1 1 Block Diagram Processor LGA775 FSB 800 1066 1333 MHz 0083 800 1066 MHz VGA Intel DDR3 240 Pin Q45 EagleLake Channel B DDR3 240 Pin DDR3 800 1066 MHz Controller Link GLCI SATA x6 Intel LANI Intel_82567LM PCI E LAN2 Intel 82574L Jmicron_JMB368 ICH10DO CODEC 4 6662 ALC888 Pcre USB reae 10 1 Pin Headerx6 USB x7 m PICMG Golden Finge DVI D ASM1442T TMDS C Pin Header S IO F81216D W83627EHG KB MS COM2 RS232 422 485 oa 4In 4 Out WSBC Q450 User Manual 4 SystemProcessor Chipsets Ethernet Expansion Slot Onboard Pin Header WSBC Q450 User Manual Up to 8GB DDR3 DRAM 2 x 240Pin DIMM Intel Q45 GMCH integrated graphic device GMA4500 4 8xRS 232 1x RS 232 422 485 1 1 Lin In Lin out Mic In 1 K B and Mouse 1 2x RJ45 Power Watchdog Timer System reset Lin In Li in 4 out 5 60 C 23 F 140 Environment Note1 eae ee 95 non condensing PICMG 1 0 Full Size SBC 338mm x 122mm Form F 13 31 x 4 8 WSBC Q450 User Manual 6 Usei MS LAN2 Law T d se caen lc
31. s F5 Previous Values IDE HDD Block Mode Enabled Enabled Auto Auto Auto Auto Enabled Auto Auto Auto Auto IDE Enabled Item Help F10 Save ESC Exit F1 General Help F7 Optimized Defaults Block mode is also called block transfer multiple commands or multiple sector read write IDE transfer access UDMA Ultra DMA is a DMA data transfer protocol that utilizes ATA commands and the ATA bus to allow DMA commands to transfer data at a maximum burst rate of 33 MB s On Chip Secondary PCI IDE The chipset contains a PCI IDE interface with support for two IDE channels Select Enabled to activate the IDE interface Select Disabled to deactivate this interface if you install a primary and or secondary add in IDE interface WSBC Q450 User Manual 25 IDE Primary Master PIO IDE Primary Slave PIO LC Secondary Master PIO Secondary Slave PIO The four IDE PIO Programmed Input Output fields let you set a PlOmode 0 4 for each of the four IDE devices that the onboard IDE interface supports Modes 0 through 4 provide successively increased performance In Auto mode the system automatically determines the best mode for each device IDE Primary Master UDMA C IDE Primary Slave UDMA C IDE Secondary Master UDMA IDE Secondary Slave UDMA UDMA Ultra DMA is a DMA data transfer protocol that utilizes ATA commands
32. tep by step run again when each register is accessed For more information about WDT please refer to Winbond W83627EHF data sheet There are two PnP I O port addresses that can be used to configure WDT 1 Ox2E EFIR Extended Function Index Register for identifying CR index number 2 Ox2F EFDR Extended Function Data Register for accessing desired CR Below are some example codes which demonstrate the use of WDT WSBC Q450 User Manual 54 Enter Extended Function Mode outp 0x002E 0x87 outp 0x002E 0x87 Assign Pin 77 to be a WDTO Signal outp 0x002E 0x2D outp 0x002F inp 0x002F amp 0xFE Select Logic Device 8 outp 0x002E 0x07 outp 0x002F 0x08 Active Logic Device 8 outp 0x002E 0x30 outp 0x002F 0x01 Clear WDTO Status outp 0x002E OxF7 outp 0x002F inp Ox2F amp OxEF Select Count Mode Second Minute outp 0x002E OxF5 outp 0x002F inp 0x002F amp OxF7 Count mode Register amp 0x08 Set Time out Value outp 0x002E OxF6 outp 0x002F Time out Value Register Exit Extended Function Mode outp 0x002E OxAA Definitions of Variables Value of Count mode Register 1 0x00 Count down in seconds Bit3 0 2 0x08 Count down in minutes Bit3 1 Value of Time out Value Register 1 0x00 Time out Disable 2 0x01 0xFF Value for counting down WSBC Q450 User Manual 55 Appendix B GPI
33. ter Yes want to restart my computer now No will restart my computer later Remove any from their drives and then click Finish to complete setup 44 WSBC Q450 User Manual 53 Appendix A Watchdog The working algorithm of the WD T function be simply described as a counting process The Time Out Interval can be set through software programming The availability of the time out interval settings by software The System Board allows users control WDT through dynamic software programming The WDT starts counting when it is activated It sends out a signal to system reset when time out interval ends To prevent the time out interval from running out a re trigger signal will need to be sent before the counting reaches its end This action will restart the counting process WDT program should keep the counting process running under normal condition WDT should never generate a system reset unless the system runs into troubles The related Control Registers of WDT are all included in the following sample program that is written in C language User can fill a non zero value into the Time out Value Register to enable refresh WDT System will be reset after the Time out Value to be counted down to zero Or user can directly fill a zero value into Time out Value Register to disable WDT immediately To ensure a successful accessing to the content of desired Control Register the sequence of following program codes should be s
Download Pdf Manuals
Related Search