BEAM 230G User Manual
Contents
1. BEAM 230G adopts powerful Osram SIRIUS HRI 230W lamp with revolutionary technology installer and any safety problems have to be removed which features high brightness and stability Please carefully unpack it when you receive the fixture CAUTION and check whether it is damaged during the transportation And please check whether the following Disconnect from mains before starting maintenance operation items are included inside the box In order to make the lights in good condition and extend the life time we suggest a regular cleaning to Moving Head One Signal Cable One the lights Omega Clamp Two Power Cable One 1 Clean the inside and outside lens each week to avoid the weakneness of the lights due to Safety Chain One User Manual One accumulation of dust 2 Clean the fan each week 3 Adetailed electric check by approved electrical engineer each three month make sure that the circuit contacts are in good condition prevent the poor contact of circuit from overheating We recommend a frequent cleaning of the device Please use a moist lint free cloth Never use alcohol or solvents There are no serviceable parts inside the device Please refer to the instructions under Installation instructions Should you need any spare parts please order genuine parts from your local dealer Dimensions 359 D x329 W x513 H mm Packing Dimensions 620 D 430 W 415 H mm Net Weight 15kg Gross W2. pin XLR output of your controller and the other side to the male 3 pin XLR input of the moving head You can chain multiple moving head together through serial linking The cable needed should be two core screened cable with XLR input and output connectors Please refer to the diagram below DMX 512 connection with DMX terminator CONTROLLER DMX Output DMX Input 3 Pin XLR Socket 3 Pin XLR Socket COMMON 1 Ground DMX512 OUT ot DMX512 IN 2 Data 8 Data SPIN XLA 3 PIN XLR For installations where the DMX cable has to run a long distance or is in an electrically noisy environment such as in a discotheque it is recommended to use a DMX terminator This helps in preventing corruption of the digital control signal by electrical noise The DMX terminator is simply an XLR plug with a 120 Q resistor connected between pins 2 and 3 which is then plugged into the output XLR socket of the last fixture in the chain Please see illustrations below 1209 N PIN 3 PIN2 Gobo 12 shake from slow to fast 200 255 Rot gobo wheel cont rotation from slow to fast rotation 128 131 Gobo rotation stop a 7 2 Dimmer 0255 0 100 Linear dimmer o e e Poze ene Rotating Pan Tilt 236 245 Blackout by all wheel changing 020 029 No function Special On Off Calibration Code Password 088 194 255 Backwards rainbow effect from slow to fast 032 039 Gobo4 048 055 Gob
3. the floor Or it might cause electronic shock to the people Make sure the installation place is in good safety condition before installing the fixture Make sure to put the safety chain and check whether the screws are screwed properly when installing the fixture Make sure the lens are in good condition It s recommended to replace the units if there are any damages or severe scratch Make sure the fixture is operated by qualified personnel who knows the fixture before using Keep the original packages if any second shipment is needed Don t try to change the fixtures without any instruction by the manufacturer or the appointed repairing agencies lt is not in warranty range if there are any malfunctions from not following the user manual to operate or any illegal operation like shock short circuit electronic shock lamp broke etc 4 Mounting and Installation Cautions For added protection mount the fixtures in areas outside walking paths seating areas or in areas were the fixture might be reached by unauthorized personnel Before mounting the fixture to any surface make sure that the installation area can hold a minimum point load of 10 times the device s weight Fixture installation must always be secured with a secondary safety attachment such as an appropriate safety cable Never stand directly below the device when mounting removing or servicing the fixture Macro function for rotatable gobo prism combina
4. 65 6 ft 82 ft Beam Diameter 2 5 Beam Angle 2 0 45m 1 45ft 2 0 67m 2 19ft 2 0 90m 2 94ft 2 1 14m 3 74ft 8 DMX Channels MERE Im 0 255 PAN Movement 054 058 058 cos e 6 BET 0 255 Fine control of Pan movement 032 035 Half Color 3 Half Color 4 059 062 Half Color 6 Half Color 7 0 255 Fine Fine control of Tilt movement of Tilt movement 0 004 Open White 005 008 Hafl White Half Color 1 014 017 Half Color 1 Half Color 2 023 026 026 Half Color 2 Half Color 3 041 044 Half Color 4 Half Color 5 Color 050 053 lt e Color 5 Half Color 6 Wheel 068 071 Half Color 7 Half Color 8 072 076 Color 8 077 080 080 Half Color 8 Half Color 9 081 085 Color 9 086 089 Half Color 9 Half Color 10 090 094 Color 10 095 098 Half Color 10 Half Color 11 099 103 Color 11 104 107 Half Color 11 Half Color 12 Q
5. CE BEAM 230G User Manual KEEP THIS MANUAL FOR FUTURE NEEDS 1 Unpacking Thank you for choosing BEAM 230G For your own safety please read this manual before 13 Maintenance and Cleaning installing the device This manual covers the important information on installation and applications The following points have to be considered during the inspection Please install and operate the fixture with following instructions Meanwhile please keep this 1 All screws for installing the devices or parts of the device have to be tightly connected and must not manual well for future needs be corroded 2 There must not be any deformations on the housing color lenses fixations and installation spots BEAM 230G is made of a new type of high temperature strength of engineering plastics and cast ceiling suspension trussing aluminum casing with nice outlook The fixture is designed and manufactured strictly following CE 3 Mechanically moved parts must not show any traces of wearing and must not rotate with standards complying with international standard DMX512 protocol It s available independently unbalances controlled and linkable with each other for operation And it is applicable for large scale live 4 The electric power supply cables must not show any damage material fatigue or sediments performances theater studio nightclubs and discos Further instructions depending on the installation spot and usage have to be adhered by a skilled
6. eight 18kg 11 Product Dimensions 2 Safety Instructions CAUTION Be careful with your operations With a dangerous voltage you can Suffer a dangerous electric shock when touching wires This device has left the factory in perfect condition In order to maintain this condition and to ensure a safe operation it is absolutely necessary for the user to follow the safety instructions and warning notes written in this user manual IS Important Damages caused by the disregard of this user manual are not subject to warranty The dealer will not accept liability for any resulting defects or problems If the device has been exposed to temperature changes due to environmental changes do not switch it on immediately The arising condensation could damage the device Leave the device switched off until it has reached room temperature This device falls under protection class Therefore it is essential that the device be earthed The electric connection must carry out by qualified person The device shall only be used with rate voltage and frequency Make sure that the available voltage is not higher than stated at the end of this manual Make sure the power cord is never crimped or damaged by sharp edges If this would be the case replacement of the cable must be done by an autho
7. hrough the center hole of the omega bracket As an added safety measure be sure to attached at least one properly rated safety cable to the fixture using on of the safety cable rigging point integrated in the base assembly O e ED O N ro tt y O ee o o 76840 Lux 15m o o Omega Bracket O o Satety Clamp 2 5 beam angle Safety Cable gt o O 1 4 Turn Quick Lock Fasteners o 8 o il 0 No need for adjustment of reflector or lamp Anti reflection lenses 1 color wheel with total 13 colors plus open s Variable direction rainbow effect with speed adjustable y 1 rotatable gobo wheels with 12 rotatable indexable and interchangeable gobos plus open e ele Variable speed gobo scrolling in both directions I u E a 12 0mm outside 8mm image diameter Gobo Size R e e e id 3 1 rotatable and indexable 8 facet prism with speed adjustable and variable direction Regardless of the rigging option you choose for your BEAM 230G always be sure to secure your fixture with a safety cable The fixture provides a built in rigging point for a safety cable on the hanging bracket as illustrated above Be sure to only use the designated rigging point for the safety cable and never secure a safety cable to a carrying handle 5 DMX 512 control connections Connect the provided XLR cable to the female 3
8. o6 064 071 Gobog 4 4 108 112 color 12 B 6 Menu Operations 113 116 Half Color 12 Half Color 13 al Function Mode DMX Address A001 AXXX 117 121 Color 13 cre Set to slave TB OOO PAN TILT Color Wheel Gobo Wheel Dimmer Focus Prism Manual Control VOS Set Signal Type Wired DMX 080 087 Gobo 10 Gobo 088 095 Wireless DMX Gobo 11 Act WDMX amp Out Edit Program Program 1 Steps 1 48 Scenes 01 Pan XXX Program8 s Scenes XX Time xx xS Mode of Channel Mode Set 16Bit Mode Wheel 096 103 Gobo 12 104 111 Gobo 1 shake from slow to fast 112 119 e OO Gobo 2 shake from slow to fast 120 127 Gobo 3 shake from slow to fast A lt 0 gt Y Cite 128 135 Gobo 4 shake from slow to fast 136 143 Gobo 5 shake from slow to fast 144 151 Gobo 6 shake from slow to fast 152 159 8Bit Mode Vector Mode Gobo 7 shake from slow to fast Design Mode 160 167 Gobo 8 shake from slow to fast Design Max Channel XX 168 175 Gobo 9 shake from slow to fast Mode Set PAN 001 176 183 Gobo 10 shake from slow to fast 184 191 Gobo 11 shake from slow to fast ll Clear Lamp On Off Time Software V1 0 V9 9 Version 7 Photometric Data Photometric Beam Angle Data 2 5 BeamAngle LUX x 0 0929 FC 10014FC 107790LUX 7139FC 76840LUX 4828FC 51970LUX 2720FC 29280LUX v_ 2 5 Beam Angle Om Oft 10m 15m 20 m 25m 32 8 ft 49 2 ft
9. rized dealer Always disconnect from the mains when the device is not in use or before cleaning it Only handle the power cord by the plug Never pull out the plug by tugging the power cord During initial start up some smoke or smell may arise This is a normal process and does not necessarily mean that the device is defective it should decrease gradually Please don t project the beam onto combustible substances Fixtures cannot be installed on combustible substances keep more than 50cm distance with wall for smooth air flow so there should be no shelter for fans and ventilation for heat radiation If the external flexible cable or cord of this luminaire is damaged it shall be exclusively replaced by the manufacturer or his service agent or a similar qualified person in order to avoid a hazard 3 Operation Instructions The moving head is for beam effect for on site decoration purpose Don t turn on the fixture if it s been through severe temperature difference like after transportation because it might damage the light due to the environment changes So make sure to operate the fixture until it is in normal temperature This light should be keep away from strong shaking during any transportation or movement Don t pull up the light by only the head or it might cause damages to the mechanical parts Don t expose the fixture in overheat moisture or environment with too much dust when installing it And dont lay any power cables on
10. s colortime 0 255 Max to min speed for color wheel from fast to slow as Gobotime 0 255 Max to min speed for gobo wheel from fast to slow 9 Key Features 3000 hour rated lamp source Osram SIRIUS HRI 230W lamp 10200lumen 7800 K 3000h included from a ceiling or set on a flat level surface see illustration below Be sure this fixture is kept at least 0 5m 1 5 ft away from any flammable materials decoration etc Always use and install the supplied safety cable as a safety measure to prevent accidental damage and or injury in the event the clamp fails Mounting points Overhead mounting requires extensive experience including amongst others calculating working load limits a fine knowledge of the installation material being used and periodic safety inspection of all installation material and the fixture If you lack these qualifications do not attempt the installation yourself Improper installation can result in bodily injury Be sure to complete all rigging and installation procedures before connecting the main power cord to the appropriate wall outlet Clamp Mounting The BEAM 230G provides two unique mounting bracket assembly that integrates the bottom of the base the included Omega Bracket and the safety cable rigging point in one unit see the illustration below When mounting this fixture to truss be sure to secure an appropriately rated clamp to the included omega bracket using a M10 screw fitted t
11. tions Variable Frost Filter Hybrid effect for Wash Dual flag mechanical dimming system Variable speed strobe effect Preset variable random strobe and dimming pulse effects Motor driven focus from near to far 540 630 PAN and 265 TILT movement Automatic Pan Tilt position correction 16 bit smooth and precise resolution for PAN TILT movement 3 phase motors for fast quiet and accurate Pan Tilt positioning and movement Vector Mode with blackout MIB function Blue LCD Display 14 DMX channels USITT DMX 512 16 bit resolution Other DMX modes available 16 DMX channels for vector mode Customizable DMX channel assignment DMX stand alone master slave sound activated mode DMX recorder and edit function integrated Software update 3 pin or 5 Pin XLR serial input output Fan cooling system Constant temperature readout management function DB rating 1M 54 18db 2 x 1 4 turn fastening Omega Clamps Electronic ballast and power supply 10 Technical Specifications Input Voltage AC90 260V 50 60Hz Light Source 1 Osram SIRIUS HRI 230W lamp Control Signal DMX512 master slave and sound activated or auto operation Control Channel 14 DMX Channels Power Consumption 392W Special Vector Mode 040 059 060 079 080 099 100 119 120 139 140 159 160 179 180 199 200 219 220 239 240 255 Internal program 4 Internal program 5 Internal program 6 Internal program 7 Internal program 8 a
Download Pdf Manuals
Related Search