ZvSync - EU
Contents
1. Power is available but the unit is DEACTIVATED GREEN The unit is powered up and ACTIVATED Infrared Jack Input for the installation of the remote infrared sensor G USB Input for installation of USB storage device used for firmware upgrade or activation of the advanced media functions Use is strictly optional Z9 Page 6 ZvSync EU User s Manual www zeevee com 1 2 REAR PANEL Q Aerial Cable RF Input Connect to the antenna for over the air reception or to a cable feed for DVB T reception HD Video Output The video output most commonly used from the receiver unit Connect to the HDMI digital input of the display device typically a television Both high definition video and digital audio are carried G CVBS Video Output For composite video output connect the CVBS Video output to the appropriate composite video input of the display device typically a television or monitor Right Audio Output For analog audio connect to the appropriate Right analog audio input on the display device typically a television or amplifier Left Audio Output For analog audio connect to the appropriate Left analog audio input on the display device typically a television or amplifier Power Connector Connect to the plug on the supplied wall mount power supply ZvSync EU User s Manual Page 7 1 3 REMOTE CONTROL LED Indicator c MG TV fear 6a O Learning ph KI NA KA2. Parameter 48 862MHz RF Input Level 20 to 82dBm IF Bandwidth 6 7 and 8MHz Modulation QPSK 16QAM 640AM 2560AM DVB T DVB T2 Video Decoder Format MPEG4 AVC H 264 HP 14 MPEG2 MP ML HL Output Format 480i 480p 576i 576p 720p 1080i 1080p60Hz Aspect Ratio 4 3 16 9 Auto Output Port HDMI v1 3C CVBS Audio Decoder Format MPEG 1 layer 1 amp 2 amp 3 WMA AC 3 Audio Output Digital Audio over HDMI RCAx2 L R USB2 0 Supported Capacity Unlimited Supported Media MP3 WMA JPEG BMP AVI Power Supply Voltage wall 100 240VAC 50 60Hz Supply Voltage 5VDC ZvSync unit Maximum Power 10W Consumption Standby Power lt 0 8W Consumption Nominal Power 5W Consumption Z9 Page 32 ZvSync EU User s Manual www zeevee com 7 Declaration of Conformity The Original Equipment Manufacturer herewith declares the conformity of the product with the following directives and standards Low Voltage Directive 2006 95 EC EN 60065 2002 A1 2006 EMC Directive 2004 108 EC EN 55 013 2001 A1 2003 A2 2006 EN 55 020 2007 EN 61 000 3 2 2006 EN 61 000 3 3 2008 FCC CE C Tick This symbol on the product or in the Dispose instructions means that your electrical and electronic equipment should be disposed of of at the end otf its life separately from Properly normal household waste There are separate collection systems for proper recycling of the constituent
3. The AC wall mount power supply has a number of adapter plates for use in a variety of locations with different provisions for connections to the AC mains Before deployment select the appropriate adapter and install it securely on the supply body Z9 Page 16 ZvSync EU User s Manual www zeevee com As supplied the power supply will likely be delivered with no adapter plate installed Several different plates are provided for a variety of different AC mains plug types Select the one appropriate for your AC mains supply outlet UK shown Insert the plug into the wall mount supply body Turn the plate clockwise about 10 degrees until it clicks into place Insure that the plate is secure before any attempt is made to plug in to the AC mains A different type of adapter plate may be installed later on To install a new plate Press the release button While holding the button rotate the installed plate approx 10 degrees counterclockwise Remove the currently installed plate ZvSync EU User s Manual Page 17 Connecting Power Supply to ZvSync The wall mount power supply included provides power for the ZvSync receiver Other methods of powering the ZvSync may void the warranty The DC input is rated at 5VDC at a maximum peak consumption of 10W nominal consumption of 6W during operation and a standby power draw of 0 8W Included AC to 5VDC Wall Mount Power Supply A R A Z9 Page 18 ZvSync EU User
4. option gt Use the RIGHT arrow key to activate a channel search A scanning status screen showing the progress of the initial channel scan will appear Channel Search 63 0MHz 6MHzZ DTV 000 Radio 000 Progress oa EXIT ZET Skip Allow the scanning process to run to completion several minutes Once the initial scan is complete OTA or Cable ZvSync may be used to start watching television programs ZvSync EU User s Manual Page 21 4 Basic Operation To access the general setup menu press the Menu button The user will see with this top level navigation screen Major categories may be selected by navigating left and right using the arrow keys Once a category is selected the options may be explored by navigating down into the page and selecting the appropriate page item After selecting a page item stepping into it by navigating to the RIGHT presents the unique options for that particular item 4 1 PROGRAM MANAGEMENT se 4 Program Program Edit EPG Sort LCN fox Metra Program Edit To edit your program preferences lock skip favorite move or delete you will need to enter the Program Edit Menu item This menu requires a password to access The default password is 000000 while the master unlock password is 888888 Page 22 ZvSync EU User s Manual www zeevee com Program Edit 4 gt 66 1 WUTF DT 66 2 WUTF DT Favorite Type 66 3 WUTF DT Disable imi Movie
5. encouraged This set of features is not actively supported by ZeeVee and support is not available for the time shifting media playing or PVR functions Media types of AVI MP3 WMA JPEG BMP etc are supported z Page 30 ZvSync EU User s Manual www zeevee com Problem No picture Screen shows No Signal Potential Reason Power is not connected Possible Action Connect power supply Check wall source The power is switched off Switch on power to ZvSync Cable feed is not connected Check Connect power cable Aerial cable is faulty Check aerial and connections No sound from speaker Incorrect or faulty connection with audio cable Correctly connect the audio cables Sound on mute Select the mute unmute on the remote Only sound no image on screen Incorrect A V cable connection Program is a radio program Check cable connections The program being tuned may be audio only Incorrect setting in digital audio Set a different audio type in World Options Remote control is not working The picture is breaking up The battery is exhausted Remote control is not facing or visible to ZvSync sense window The input signal is too weak Replace the remote control s batteries Reorient ZvSync sense window and remote control Check aerial cable and connections ZvSync EU User s Manual Page 31 29 Item Sub Item Input Frequency
6. l E s Paa Buttons nai GO a He SLEEP Active nge Definitions m c MW PAUSE HH CH LE a ia i JA OK pv Fi a Y Pa Lat Ei INI oO REPE i O E Color Buttons Z9 Page 8 ZvSync EU User s Manual The ZvSync receiver decoder is supplied with a partial learning remote control device Buttons P1 P5 can be programmed to mimic the functions of a select set of buttons from another remote control unit The intention is that the TV viewing experience can be controlled from a single handset to include power and volume control of the television set and all other functions directed at controlling the Zvsync receiver decoder As the design of the remote control device is used in multiple applications some buttons have multiple legends or marks In general for the ZvSync application the markings shown on the silkscreen white marks above or beside buttons are the active definitions of the key function www zeevee com Button Definitions Key Definition Power Pressing once turns on ZvSync Again turns it off Mute Disables Enables audio Reverses playback while in PVR mode Fast Forwards playback while in PVR mode Starts Playback when using PVR mode Back up to division in PVR mode Pauses playback in PVR mode Advances to division when using PVR mode EPG sLEEp Displays Electronic Program Guide information Quick channel up and down buttons when watching t
7. RECEIVER The ZvSync EU receiver decoder is supplied with an external IR receiver This is in the form of a cable with an IR receiver at the end The pigtail MUST be installed for the ZvSync to receive commands from the remote and is required for proper operation By separating the infrared receiver from the base unit the main body of the ZvSync receiver decoder can be installed in an unobtrusive location with only the IR sensor showing IR Sensor cS ieee ee ua 1 Meter 10erm i gt Connecting to ZvSync The 3 5mm plug on the infrared pigtail must be plugged in to the front IR port on the ZvSync main unit for proper operation ja T ng o ZVSync ox DVB T Tuner Decoder ZvSync EU User s Manual Page 15 29 Usable Angles The remote control must have a relatively unobstructed line of sight to the infrared sensor The usable angles are quite flexible yielding many possible mounting options Common is to use the included double sided tape to mount the IR sensor to bottom or side bezel of the attached television At the user s discretion the main body of the ZvSync EU receiver decoder may be placed out of sight providing the proper ventilation considerations are observed 2 5 CONNECTING TO THE POWER SUPPLY The wall mount power supply included provides the power for the ZvSync receiver Any other method of powering the ZvSync may void the warranty Configuring the Power Supply
8. ngpa wa haaa ha RAW 12 2 2 CONNECTING TOA CABLE FEED 0 0 12 2 3 CONNECTING TO THE TELEVISION 17 a a acc Hapee aes ees 13 14 IOWA AA Bee oe Cee eee eee 13 RCA CableS APP APA 14 2 4 INFRARED REMOTE CONTROL RECEIVER 15 16 Connecting to NS NG oonu aana 15 Weable ANGIGS 2244544 ka be Dh wa ec KGG ener AK 16 2 5 CONNECTING TO POWER SUPPLY oi x3 awkagsa magat 16 18 Configuring the Power Supply 16 17 Connecting the Power Supply to ZvSync 18 3 Installation Wizard aaa Kanaa map nka BGY BED Ah LhEDA 19 21 4 Basic Operation 000 0 0 00000 eee 22 4 1 PROGRAM MANAGEMENT 0000 00 ee 22 24 4 2 PICTURE SETTINGS 45 44sneldde pe eeos cee eens onesies 25 4 3 CHANNEL SEARCH 0 0 0 00 ccc eee eee 26 4 4 TIME SETTING cartes oe hee oo SS ee AA AA 27 4 5 WORLD OPTION SETTINGS maang ma a KAN kA Kaka Kna dak 28 4 6 SYSTEM SETTINGS oonan anaana aaae 29 4 7 USB amp MULTIMEDIA wees was o os 44 Shes Bak eS 30 MOUDICSNOOUN Gs acnec244syeteceetaecos eurnsesaseenes 31 6 Technical Specifications 0 0 0 a 32 7 Declaration of Conformity 0 00 0 0 aaa naaraana 33 ZvSync EU User s Manual Page 5 29 1 Before Using the Product This section provides detailed descriptions of the product and included accessories 1 1 FRONT PANEL O ZvSync Ox DVB T Tuner Decoder LED Status Indicator Indicates state of unit RED
9. s Manual www zeevee com 3 Installation Wizard If you are using the receiver for the first time or have restored it to factory defaults the installation guide menu will appear on your screen Installation Guide OSD Language English Country Austria Channel Search OK Confirm gt Select the desired language for the On Screen Display interface gt Select the country or closest match to the country in which you will be operating the ZvSync EU device e This is important for properly find the broadcast channels 5 Navigate to the Channel Search option and the press OK e The ZvSync unit will then begin searching for channels Allow it to run to completion This can take several minutes e On completion the ZvSync should be ready for use viewing programs ZvSync EU User s Manual Page 19 After exiting the Installation Guide screen the following screen will appear e aO G Program Program Edit EPG Sort LCN oe Return Eg Confirm gt Use the RIGHT arrow key to navigate to the Channel Search page gt Use the DOWN arrow key to navigate to Signal Type gt Use the RIGHT arrow key bring up the Air option o Channel Search Auto Search Manual Search Country Antenna Power Signal Type Cable Ea Confirm Page 20 ZvSync EU User s Manual www zeevee com With the Air option highlighted gt Use the UP arrow to navigate to the Auto Search
10. News Sport Music 12 00 14 00 The a No Good Confidant E Move EB skip bel Lock O Delete as FAV rename Set Favorite Channels You can create a short list of favorite programs channels that you can easily access Set Favorite TV Program 1 Select your desired channel then press the FAV button A symbol will appear and the channel is marked as a favorite 2 Repeat the previous step to select more favorite channels 3 Confirm and exit the menu by pressing the EXIT key Disable Favorite TV Program Select the Favorite channel and press the FAV button on the remote to bring up the menu that allows cancelling of a favorite View Favorite Channel 1 While in normal viewing mode press the FAV button and the favorite program menu will appear 2 Press the up and down arrows to browse to a selection 3 Press the OK button to select that program ZvSync EU User s Manual Page 23 z4 Delete a TV Program 1 Select the program and then press the BLUE button A warning message will appear 2 Press OK to delete the channel 3 Repeat the process if more channels need to be deleted 4 Hit EXIT to complete Lock Program You can lock certain channels for restricted viewing using ZvSync 1 Select a particular channel and then press the YELLOW button A lock shaped symbol is displayed The channel is now locked from selection 2 Repeat the process as needed for all desired channels 3 To confirm your select
11. User s Manual ZY ZvSync EU HD Digital Tuner Decoder DVB T DVB T2 Warnings Cautions and Notes Throughout the entire user s manual pay special attention to the following marks that Indicate hazardous situations Warning Indicates a hazardous situation which could result in serious injury Caution Indicates a situation which could damage the equipment or other apparatus Note Indicates additional information to make the user aware of possible problems and important information to help understand use and maintain the installation Important Symbols Cy Pern CAUTION To reduce risk of electric shock do not open unit or breach power supply enclosure There are no user serviceable parts inside Contact ZeeVee support at 1 877 493 3833 DANGEROUS VOLTAGE This symbol indicates dangerous voltage inside the receiver that presents a risk of electric shock or personal injury This symbol indicates important instructions accompanying the receiver l IMPORTANT INSTRUCTIONS Z9 Page 2 ZvSync EU User s Manual www zeevee com Safety Instructions and Precautions This receiver has been manufactured to comply with international safety standards Please read the safety precautions carefully 1 Main Supply 100 240V 50 60Hz AC e Operate this product only from the type of power source indicated on the marking label If you are not sure of the type of power supplied to the location where the receiver is to
12. be used consult your local power company Disconnect the product from the main power source before you start any maintenance or installation procedures 2 Connection to the Cable Feed or Aerial e Disconnect the product from the AC mains before connecting or disconnecting the cable from the aerial jack 3 Connection to the Television e Disconnect the product from the AC mains before connecting or disconnecting a cable from the receiver to the attached television Failure to do so can damage the television 4 Overloading e Do not overload a wall outlet extension cord or adapter as this may result in electric fire or shock hazard 5 Liquids e This product should not be exposed to liquid of any kind In addition no objects filled with liquid should be placed on the apparatus 6 Cleaning e Disconnect the product from the wall outlet prior to cleaning e Use a light damp cloth no solvents to dust or clean the product ZvSync EU User s Manual Page 3 zo 7 Ventilation e The slots and openings on the case of the product must be left uncovered to allow for air to pass in and out for proper cooling e Do not operate the product on soft furnishings or carpet e Do not stack anything on top of the product 8 Attachments e Do not use unsupported attachments as these may be hazardous or cause damage to the product 9 Extraneous Objects e Do not insert anything into the openings of the unit 10 Location e Pla
13. ce the product indoors and avoid exposing it to lightning rain or direct sunlight e Do not place the product near a radiator or heat register e Try to place the unit at least 2 inches 10cm from any appliance susceptible to electromagnetic influences such as a television or radio e Insure the ventilation considerations are followed when the unit is in service e Do not place the product on an unstable cart stand tripod or bracket where it can fall A falling object can cause injury and may cause serious damage to the product 11 Lightning Storm or Not in Service e Unplug the product from the wall outlet and disconnect the aerial during a thunderstorm or when left unattended and unused for long periods of time This will prevent damage due to lightning or power surges 12 Replacement Parts e Replacement parts should be purchased through an authorized ZeeVee distributor and approved by the manufacturer Unauthorized parts may result in damage to the units and will void any warranty z Page 4 ZvSync EU User s Manual www zeevee com 1 Before Using the Produet 0000 000 a aaaea 6 1 1 FRONT PANE eh oat ook Ye ANA NA oS goin NeW eee AA Mana 6 1 2 REAR PANEL Uwak eee en wees a od dows PAL ee KAYA 7 1 3 REMOTE CONTROL 224 5 5 DD ha sodden haba eeeeeeaees 8 Button Definitions 2455s oes eee tee eee 9 Programmable BULIONS 2 lt 06655 04000 e46heeu8wn 10 11 dko Ci AAP 12 2 1 CONNECTING TO AN AERIAL Ja nas
14. elements For more information please contact your local environmental authority or the retailer where you purchased the product ZvSync EU User s Manual Page 33 Z9 Contact ZeeVee Support Contact us for installation and technical support repairs and warranty service 1 877 4ZEEVEE 1 877 493 3833 support zeevee com Representatives are available from 9 00 AM to 6 00 PM Monday through Friday Eastern Time Sales North America 1 347 851 7364 Phone sales zeevee com EMEA 44 1494 956677 Phone EMEAsales zeevee com 29 Page 34 ZvSync EU User s Manual www zeevee com ZvSync EU User s Manual Page 35 ZvSync EU_70 00042 00 RevA
15. elevision programs Stops playback when using PVR mode Causes PVR mode to be entered during normal playback Enables disables Closed Captioning EX Cancels Exits menu levels when navigating interface Activates PVR mode Displays options Displays current playback information Causes repeat mode to be entered when playing stored media JJ 4 Color buttons Program specific meaning Dash button for entering digital channel numbers ie 23 1 RECALL Recall last channel being played ae Numeric digits for entering channel numbers A gt Navigation buttons when driving configuration interface KONE During normal playback Up Down sets channels O Left Right sets volume and OK displays channel list ZvSync EU User s Manual Page 9 Programmable Buttons O LED The upper left portion of the remote houses a set of programmable keys The intent is to allow for common television functions to be programmed so the user only needs to use a single remote control device to manage their television experience when using the ZvSync receiver decoder Keys P1 though P5 can be set to any function the user desires The labeling is present only to provide visual cues the user may use to help remember which key has been programmed to which function The SET key has a fixed function that is not programmable It initiates the programming process for setting the P1 P5 key functi
16. ions and actions press the EXIT button 4 Press the YELLOW button to disable the locked channels function 5 To view the locked channels you will be required to enter your password The password can be a user set password The default of 000000 The master unlock password is 888888 EPG Electronic Program Guide The Electronic Program Guide is an on screen TV guide that shows scheduled programs for every tuned channel Press the EPG button to access the information You can use the arrow buttons to select a preferred program If there is more than one page of information on the program use the BLUE and YELLOW buttons for page up and page down respectively Sort Sort your channels using the following options LCN sorts by Logical Channel Number in ascending order Service Name Sort in alphabetical order Service ID Ascending Order according to the station ID ONID Sorts by ascending order by the Original Network Identifier z Page 24 ZvSync EU User s Manual www zeevee com 4 2 PICTURE SETTINGS Picture Aspect Ralio 16 9 Wide Screen Resolution 1080 TV Format PAL Video Output YPbPr The allowed output video settings can be adjusted at the Picture top level settings page When the HDTV port is connected via HDMI to the display television all the settings are honored If component video CVBS or RF modulation are being used to send the video to the display device the only supported resolutio
17. n is 576i regardless of the setting on the resolution item ZvSync EU User s Manual Page 25 4 3 CHANNEL SEARCH The Channel Search top level navigation page allows the ZvSync tuner decoder to rescan for channels and change settings relevant to the attached reception method ma o PU R ee Channel Search Auto Search Manual Search Country Austria Antenna Power Off Auto Search Automatically searches for channels and saves them once the scan is complete All previous entries will be deleted gt Select Auto Search and press OK or RIGHT arrow to start 5 To cancel press EXIT Only found channels will be saved Manual Search Allows for the addition of individual channels without deleting the previously saved channels and settings User must know the exact center frequency of the channel of interest Antenna Power Disable if an external powered antenna is employed Signal Type Select AIR if receiving from an Antenna Select Cable if receiving from a Cable Provider or ZeeVee encoder modulator product z Page 26 ZvSync EU User s Manual www zeevee com 44 TIME SETTING NW KK Time Time Offset Auto Country Region Eastern Time Zorii Sleep Off Power On Off Ci Return ET Centi Time Offset Automatic or manual GMT time offset adjustments Country Region Select country of interest for use with Auto Time Offset adjustments Time Zone Time zone when Time Offset is set to man
18. ons Programming P1 P5 Buttons The ZvSync remote has been tested to be compatible with a large number of remotes However some manufacturers use infrared codes that are obscure and cannot be copied into the programmable keys of the ZvSync remote User Remote ZvSync Remote to be copied 2 inches or 5cm Z9 Page 10 ZvSync EU User s Manual www zeevee com To program a key the following sequence shall be executed Step1 Press and hold the SET button for three seconds gt The RED LED lights immediately when the button is pressed gt After 3 seconds the LED changes to a very bright state Step 2 Press the key you wish to program P1 P5 gt The RED LED changes to a slow flash 1 second Step 3 Press the key on the remote that you are copying gt The RED LED performs three quick flashes to acknowledge gt RED LED turns on solid again gt Repeat steps 2 and 3 or simply wait for light to extinguish Step 4 Test Programmed key on television or device to be controlled If command is not executing properly repeat steps 1 3 ZvSync EU User s Manual Page 11 2 Setup This chapter describes how to connect your ZvSync Receiver to the television and receiving apparatus appropriately The receiver has various options and interface for connectivity Select the method appropriate to your application 2 1 CONNECTING TO AN AERIAL Connect your antenna to the ZvSync receiver s RF IN jack for over the air recep
19. tion as follows Connect ANT jack on ZvSync to Aerial for O T A content or Cable feed from wall jack LWES Sh ful O XU Aa 2 2 CONNECTING TO A CABLE FEED To receive a cable signal or a channel generated by ZeeVee s encoder modulator products connect to the RF IN jack on the rear face with a cable to the source feed Z9 Page 12 ZvSync EU User s Manual www zeevee com 2 3 CONNECTING TO THE TELEVISION HDMI Cable A connection to the HDMI input of a television if so equipped is the recommended method to get visual content on to the television display Both visual content and audio content are carried over the single cable from the ZvSync to the television display The digital connection presents the highest resolution sharpest picture possible from the ZvSync receiver HD Television ZvSync EU User s Manual Page 13 zo RCA Cables Certain televisions or applications do not have digital video inputs The ZvSync will output standard definition representations of the programming over the CVBS port Both the CVBS output and the HDTV digital output are active simultaneously All content will be scaled down to 576i regardless of the incoming resolution prior to being sent out the CVBS port ANT CVAS Supplied CVBS Audio RCA Cable SD Television O ba O NG IN O CVBS RT LT Z9 Page 14 ZvSync EU User s Manual www zeevee com 2 4 INFRARED REMOTE CONTROL
20. ual Sleep Allows setting of an interval after that the ZvSync will automatically shut off Power On Off Allows setting a schedule for time of day activation and shutdown of the ZvSync device ZvSync EU User s Manual Page 27 29 4 5 WORLD OPTION SETTINGS Option OSD Language English Audio Language English Digital Audio PCM CO Return ox Confirm The Option screen allows for setting the On Screen Display language and the audio language to be played if the incoming program allows for those options Digital Audio Allows setting various types of audio to be output over the HDTV port Page 28 ZvSync EU User s Manual www zeevee com 4 6 SYSTEM SETTINGS amp Parental Guidance Set Password Restore Factory Default Information Software Update Ea Con lin Various System Parameters Default user password is 000000 Master unlock password is 888888 ZvSync EU User s Manual Page 29 4 7 USB amp MULTIMEDIA E al Multimedia Photo Configure Movie Configure PVR Configure The ZvSync device supports a rich set of features enabled through the use of a USB In order to support the PVR functions of time shifting and recording a storage device must be present It is recommended that a high performance USB storage device be used if these functions are to be utilized The format must be FAT32 NTFS is not supported Use of the PVR and media storage functions is freely available and
Download Pdf Manuals
Related Search