CHAPTER 1 - INTRODUCTION
Contents
1. bar 1x230 Vac 10 3x230 400 Vac 10 50 Hz 3 5 mt with standing valve recommended CHAPTER 3 INSTALLATION The installation operations must be performed by expert qualified personnel A DANGER Use specific guards and equipment as per safety standards Fully comply with safety and accident prevention standards in force DANGER Warns that the failure to follow the directions given may cause Electric shock risk electric shock 3 1 HYDRAULIC CONNECTION The system can be used with a direct connection to the aqueduct or suction from a first tank For connection to the aqueduct pay full attention to local standards in force A DANGER Check the sum of the intake pressure and the maximum pressure of the motor pump do not exceed the maximum values allowed by the system SSCX series electropumps are not self priming It is advisable to install it under the level of the water If the electropump is to be installed above the water level then a suction pipe should be used with a diameter equal to that of the suction duct for electropump If the height between the pump axis and the minimum basin level is over 4 meters use a tube with a larger diameter The suction line should be perfectly airtight No elbows and or slopes should be present to prevent the formation of air locks that could affect the electropump efficiency A standing valve with filter should be fitted at about half a me2. tubing 3 2 ELECTRICAL CONNECTIONS Verify that the voltage and frequency of the electropump shown on WARNING the nameplate correspond to those available on the mains DANGER The installer must make sure that the electric system is grounded in Electric shock risk accordance with the law in force DANGER Make sure that the electric system has a high sensitivity circuit Electric shock risk breaker D 30 mA DIN VDE 0100T739 gt gt gt Single phase motors have a permanently inserted condenser and a thermal protection fitted on the motor winding Customers will be responsible for protections of three phase motors Electric connections should be performed using cables HO7RN F for external connections HO5RN F or HO7RN F for internal connections CHAPTER 4 STARTING THE UNIT A WARNING Use the electropump for the applications listed on the nameplate a WARNING Do not operate the electropump without fluids A WARNING Do not operate the electropump when the interception valve on the delivery side is completely closet Before starting the electropump fill the electropump body as indicated at item 3 2 Priming check that it rotates clockwise when looking at the electropump from the side of the motor fan On the three phase electropumps it is possible to invert the rotation by changing the order of two phases It is advisable to empty the electropump and repeat the above describ
3. tubing can exit the outlet tubing 6 4 ELECTRICAL CONNECTION BOARD MONO SINGLE PHASE _THREE PHASE Sy 400 V We Us va CHAPTER 8 GUARANTEE This device is covered by legal guarantee based on the current standards in force for the country of purchase relating to manufacturing malfunctions and defects and or those of the material used The guarantee is limited to repairs or replacements in the assistance centres authorised by Pentair PENTAIR WATER ITALY Sri for the pump or parts deemed malfunctioning or faulty The components subject to wear for example the mechanical seal and counter face rings and seals rotors and hydraulic parts and membrane and electric cables are guaranteed for a period not exceeding their useful life For the correct use and duration of the product as well as to avail of your right to guarantee it is necessary to have parts serviced based on their use by authorised assistance centres as well as their possible replacement To exercise your right to guarantee in the case of malfunctioning directly contact the authorised dealer and or the assistance centre Possible notification of the faulty product must be sent immediately after finding the anomaly and within and not after the terms specified by law The right to guarantee runs from the date of purchase and must be proven by the purchaser by presenting the proof of purchase document receipt invoice or delivery docume
4. CHAPTER 1 INTRODUCTION 2 2 ee sa ehe 9 11 GENERAL SAFETY 7 9 12 GENERAL 9 1 3 PRELIMINARY CHECKS arisoona Raai a 9 CHAPTER 2 TECHNICAL FEATURES u ee 9 2 1 lt EIMITATIONSt a Ener eed an ant Need 9 CHARTER 3 INSTALLATION 2 22 a iaa 10 3 1 HYDRAULIC 707 aaa TE ANE EA 10 222 PRIMING ica 10 3 21 NEGATIVE SUCTION HEAD al 10 3 22 POSITIVE SUCTION HEAD iiaia ida debas 11 3 2 ELECTRICAL CONNEC TIONS ciiise o ardre aeaa ea aa e ieai Ea Eat Aa Ea aE EE 11 CHAPTER 4 STARTING THE UNIT coi ee 11 CHAPTER 5 MAINTENANCE AND TROUBLESHOOTING 11 CHAPTER 6 TABLES AND DESIGNS 32 4 do 12 61 DATA PLATE corvina dia 12 6 2 POSITIVE SUCTION HEAD 5 0 14 6 3 NEGATIVE SUCTION HEAD 14 6 4 ELECTRICAL CONNECTION 15 CHAPTER 7 GUARANTEE 0 15 CHAPTER 1 INTRODUCTION 1 1 GENERAL SAFETY INSTRUCTIONS Warnings for the safety of individuals and objects Carefully follow the instructions marked with the following symbols DANGER Warns that the failure to follow the directions given could cause serious risk to individuals or objects DANGER Electric shock risk Warns that the
5. ction 2 Reset the direction of rotation CHAPTER 6 TABLES AND DESIGNS 6 1 DATA PLATE PENTAIR WATER ITALY Srl gt Masaccio 13 56010 Lugnano PI Pentair Water ITALY SSCX 200 18 M Qmax 200 1 1 Hmax 18 m 1 Ph 230 V 50 Hz 2850 rpm CLF P1 0 9 kW 1 2 HP AA 16 wE_Ve 450 iquid temp 90 C max Nr GOG22 2006 MADE IN ITALY CONTINUOUS DUTY THERMALLY PROTECTED 91007040 66068000 1 Type of motor pump 7 Maximum head in metres 2 Maximum flow rate 8 Frequency 3 Number of phases Power voltage 9 Rotating speed 4 Absorbed power Kw Hp 10 Condenser voltage 5 Maximum temperature of liquid 11 Condenser capacity ver 1 230V 12 Insulation class and level of protection 6 Date and year of production 13 Absorbed current 12 6 2 POSITIVE SUCTION HEAD INSTALLATION 6 3 AUN Basin or tank Filter Shut off valve Non return valve 5 Motor pump 6 Gauge 7 Outlet tubing NEGATIVE SUCTION HEAD INSTALLATION Basin or tank Filter Shut off valve Non return valve 5 Motor pump 6 Gauge 7 Outlet tubing For the installation of the positive suction head ensure the correct inclination of the suction piping until the air present in the
6. ed operations if the electropump is not used for long intervals of time CHAPTER 5 MAINTENANCE AND TROUBLESHOOTING WARNING Make sure the machine is disconnected from electric power supply DANGER before performing servicing operation Electric shock risk 11 Under normal conditions SSCX electropumps do not need any type of maintenance In order to avoid possible failures it is advisable to periodically check the pressure supplied and current absorption A decrease in pressure is a symptom of wear An increase in current absorption is a sign of abnormal mechanical friction in the pump and or motor If the electropump is not going to be used for long periods of time it should be emptied completely rinsed with clean water and put in a dry place PROBLEM POSSIBLE CAUSE REMEDY 1 Verify the presence of voltage The electropump does 1 No power 2 Verify the cause and reset the switch If the not pump water the 2 Motor protection tripped thermal circuit breaker has tripped wait for the motor does not run 3 Defective condenser system to cool down l 4 Shaft blocked 3 Replace the defective condenser 4 Verify the cause and unblock the electropump 1 The pump is sucking air 1 a Make sure that the joints are The motor runs but the airtight b Check that the level of liquid has electropump does not not lowered c Check that the foot valve is pump liquid airtight and is not blocked 2 Wrong rotation dire
7. failure to follow the directions given may cause electric shock WARNING Pb Warns that the failure to follow the directions given could damage the electropumps WARNING Read this manual carefully before installing this pump Any damage caused by failure to observe the directions contained in this manual will not be covered by warranty 1 2 GENERAL INFORMATION Series SSCX comprises single bloc centrifugal electropumps without self priming device with front suction radial delivery and with 1 stage Every electropump is carefully tested and packed during its assembly 1 3 PRELIMINARY CHECKS A WARNING Always keep the original packaging for possible future transport of the machine Check the packaging is intact Open the packaging and remove the machine Check the machine corresponds to that ordered Check the machine is not damaged If you receive an incorrect or damaged machine notify PENTAIR PUMPS or the authorised dealer within and not after 10 ten days from date of purchase CHAPTER 2 TECHNICAL FEATURES A DANGER Do not use the product in environments with acid corrosive and or inflammable gas Do not use the motor pump with dangerous liquids 2 1 LIMITATIONS Ambient temperature Maximum temperature of liquid Level of protection Maximum operating pressure Power voltage Inbound frequency Maximum suction height 0 C to 40 C 90 C IP55 8
8. nt The guarantee is forfeited if the fault is caused by incorrect treatment or operations or incorrect implementation or storage incorrect electrical or hydraulic connections or no or inadequate protection or if the system or installation of the device was not carried out correctly if the fault is due to acts of God or other external or uncontrollable factors if the product is used with abrasive or corrosive liquids or different from those authorised or are incompatible with the materials used in the construction of the pumps in relation to product use those beyond the plaque limits or conditions not allowed and intervention by the purchaser or unauthorised personnel to fully or partially dismantle the product as well as changes made or tampering if the materials are damaged due to normal wear and any use different from those indicated in the use and maintenance manual is not guaranteed if not expressly indicated in writing by the manufacturer We recommend you carefully read the instructions booklet in advance Warning If your device doesn t work check the fault is not caused for other reasons for example a power supply cut to the control or command device or mishandling Remember to attach the following documentation to the faulty device receipt of purchase invoice receipt and a detailed description of the fault 15
9. tre below the fluid that has to be pumped on one end of the line Load losses can be reduced using delivery piping with a diameter equivalent or greater than the electropump mouth It is advisable to install a check valve directly on the delivery line to prevent the electropump being damaged by water hammer A cut off valve should also be installed downstream from the check valve to facilitate servicing operations Piping should be fitted so that vibrations when existing tension and weight do not affect the pump Piping should be routed along the shortest and straighter track avoiding an excessive number of bends 3 2 PRIMING A DANGER Never start the machine if it is not completely filled with water 3 2 1 NEGATIVE SUCTION HEAD For negative suction head filling of a machine proceed as follows Close the gate on the delivery tubing Open the priming plug Slowly open the gate on the suction tubing When the liquid flows out of the priming plug continuously tighten the plug Fully open the gate on the delivery and suction tubing 10 3 2 2 POSITIVE SUCTION HEAD For positive suction head filling of a machine proceed as follows e Open the gate on the suction tubing e Close the gate on the delivery tubing e Open and remove the priming plug e Pour the liquid into the machine through the priming plug hole until the liquid starts overflowing Close the priming plug e Start the machine e Open the gate on the delivery
Download Pdf Manuals
Related Search