10/100/1000Mbps PCI Gigabit Ethernet Adapter
Contents
1. installation and usage of this adapter for network installers and users The Gigabit network adapter complies to 64 32 bit for 64 bit model or 32 bit for 32 bit model PCI specification and supports half full duplex feature which can double network speed This adapter supports 1000Mbps Gigabit 100Mbps and 10Mbps network speed 1000BaseT operates on all four pairs of category 5 UTP cable 100BaseTX operates on two pairs of category 5 UTP cable and 10BaseT operates on Category 3 4 or 5 UTP cable With the Auto Negotiation technology network speed is auto detected When you connect the adapter to Gigabit Switch or another Gigabit NIC the speed will be doubled to 2000Mbps 1000Mbps Transmit and 1000Mbps Receive If you connect the adapter to 100BaseTX hub the network speed is 100Mbps Similarly if the hub is a switching hub which supports full duplex function then the speed will be doubled to 200Mbps This adapter supplies many drivers including Microsoft Windows 98SE Me NT 2000 XP Netware Server 5 x 6 x Netware ODI for DOS Linux Unix and MAC Whatever your requirements are ease of installation superior performance or responsive support backed up by unlimited technical support this adapter is the superior choice 1 Features amp Benefits Supports 64 32 bit for 64 bit model or 32 bit for 32 bit model 66 33MHz PCI Local Bus Master Version 2 2 2 1 Comply with the IEEE 802 3 IEEE 802 3u IEEE 802 3ab2. 10 100 1000Mbps PCI Gigabit Ethernet Adapter 64 bit Model 64 32 bit 66 33MHz PCI 32 bit Model 32 bit 66 33MHz PCI User s Manual This equipment has been tested and found to comply with the limits of a Class B computing devices pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications If you suspect this product is causing interference turn your computer on and off while your radio or TV is showing interference If the interference disappears then when you turn the computer off and reappears then you turn the computer on something in the computer is causing interference You can try to correct the interference by one or more of the following measures he Reorient Relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit difference from that to which the receiver is connected 4 Ensure that all expansion slots on the back or side of the computer are covered Also ensure that all metal retaining brackets are tightly attached to the computer D Ww Thank you for purchasing our Gigabit Ethernet Adapter This guide is to provide the
3. IEEE 802 3x Supports IEEE 802 3x full duplex flow control Supports IEEE 802 1Q VLAN tagging Supports Wake On LAN power management function e Plug and Play installation auto setup IRQ and I O address e Auto Negotiation full half duplex Topology e Connector Standard e Transmission Rate Hardware Required e IRQ Line I O Address e Drivers LEDs Dimension e Temperature e Humidity e Certification Star RJ 45 IEEE 802 3 10BaseT IEEE 802 3u 100BaseTX IEEE 802 3ab 1000BaseT 10Mbps 20Mbps 100Mbps 200Mbps 1000Mbps 2000Mbps IBM compatible PC with available PCI slot PCI 2 2 2 1 64 32 bit 66 33MHz Assigned by system Assigned by system Windows 98SE Me NT 2000 XP Netware Server 5 x 6 x Netware ODI for DOS Linux Unix MAC Speed Link Activity for 64 bit Model Link Activity for 32 bit Model 163 x 45 mm for 64 bit Model 120 x 45 mm for 32 bit Model 32 131 F 0 55 C 10 to 95 Non condensing FCC Class B CE Mark C tick 1 Hardware Installation To insert the network adapter into your PC follow the steps as below 1 Turn off the computer and remove its cover 2 Insert the adapter into a PCI slot 3 Secure this adapter to the rear of the computer chassis and put back the computer cover 4 Connect the adapter to the network using twisted pair cable 2 Driver Installation Use the drivers sup
4. itten consent of the manufacturer All brand and product names are trademarks and or registered trademarks of their respective companies
5. plied by the diskette included in this product For detail description please execute the readme exe in the root directory of the diskette provided by this product If you experience any problems with the adapter please make sure the appropriate driver is loaded the proper cable is connected to the adapter port and the hub switch complies with the adapter specification such as 10Mbps 10BaseT 100Mbps 100BaseTX and 1000Mbps 1000BaseT then check the LED The adapter provides LEDs to indicate network status E Speed The LED indicates the adapter is connected to 10BaseT 100BaseTX or 1000BaseT network When the light is OFF it indicates that the adapter is connected to 10BaseT network When the light is ON in amber color it indicates that the adapter is connected to 100BaseTX network When the light is ON in green color it indicates that the adapter is connected to 1000BaseT network E Link Activity The LED indicates if the UTP has been LINK ok or not When the light is OFF it indicates that the UTP port has not been connected or LINK not ok When the light is ON it indicates that the UTP port LINK ok When the light is BLINKING it indicates that there is traffic flow on the network which the adapter is connected to Copyright 2003 2004 by the manufacturer of this product No part of this manual may be reproduced transcribed stored in a retrieval system translated into any language or computer language without the prior wr
Download Pdf Manuals
Related Search